• Shenzhen Tuozhu Technology Co., Ltd. v. Stratasys, Inc.All claims unpatentable
  PTAB · Oct 5, 2026 · IPR2025-00438 · APJ Lilan Ren · IPR · Final written decision

  Claims 1–5, 7–13, and 16–20 are unpatentable; the Board found the challenged claims unpatentable on the grounds set out in its conclusions and summary table.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner’s definition of the level of ordinary skill in the art, and Petitioner’s definition appears consistent with the disclosures of the ’466 patent and the prior art of record. Accordingly, we adopt Petitioner’s definition. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001). C. Claim Construction” slip op. at 12

  • BurdenUnpatentable

    “Decision under 35 U.S.C. § 318(a) as to the patentability of the challenged claims of the ’466 patent. For the reasons discussed below, we determine Petitioner has established by a preponderance of the evidence that claims 1– 5, 7–13, and 16–20 of the ’466 patent are unpatentable.” slip op. at 2

  Patent outcomesUS 10,569,466 unpatentable
  Nonecites Phillips · KSR · Graham
  Patents in suitUS 10,569,466
• Uatp IP LLC v. Slick Slide LLCSome claims unpatentable
  PTAB · Oct 2, 2026 · PGR2024-00054 · APJ Brian D Range · PGR · Final written decision

  Claims 22–26 are unpatentable based on obviousness; claims 1–17, 27, and 28 were not shown unpatentable. Patent Owner’s motion to terminate was denied.

  RulingsFinal written decision

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed board ownDecided for patent owner

    “1. Mesh Layer Petitioner contends “no formal claim construction is necessary in this” slip op. at 13

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

    “5. Analysis On this complete record, we determine that Petitioner’s arguments do” slip op. at 31

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable

    “form of nylon and some form of Teflon (and possible combinations thereof) having the specific coefficient of friction range given in limitation [1c] breaks down, because the building blocks of the obviousness argument are not sufficiently identified in Phillips alone, nor in the supporting testimony. Accordingly, we determine that Petitioner’s arguments and evidence fail to show that Phillips renders the challenged claims obvious. 6. Conclusion Based on the foregoing, we determine that Petitioner has not established by a preponderance of the evidence that claims 1–4, 6, and 7 would have been anticipated by or obvious in view of Phillips.” slip op. at 33

  • Obviousness (§103) › Objective indicia / secondary considerations › NexusObjective indicia no nexusDecided for petitioner

    “2. Products and Nexus We first consider the issue of whether certain evidence relied upon by” slip op. at 20

  Patent outcomesUS 11,998,854 mixed
  Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · Graham · Nautilus
  Patents in suitUS 11,998,854
• Shenzhen Tuozhu Technology Co., Ltd. v. Stratasys, Inc.All claims unpatentable
  PTAB · Sep 29, 2026 · IPR2025-00532 · APJ Hyun J Jung · IPR · Final written decision

  Claims 1–16 are unpatentable under § 103 over Warren, Warren and Dunn, Calderon and RepRap20208, and Calderon, RepRap20208, and Dunn.

  RulingsFinal written decision

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable

    “of ordinary skill in the art would have made the proposed combination in the manner asserted with a reasonable expectation of success. Weighing our underlying factual determinations, a preponderance of the evidence persuades us that claim 7 of the ’381 patent is unpatentable over Calderon, RepRap20208, and Dunn. Arctic Cat, 876 F.3d at 1361.” slip op. at 108

  • Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication establishedDecided for petitioner

    “involves a case-by-case inquiry into the facts and circumstances surrounding the reference’s disclosure to members of the public.” In re Klopfenstein, 380 F.3d 1345, 1350 (Fed. Cir. 2004). Whether a document qualifies as a printed publication is a legal conclusion based on underlying factual determinations. Medtronic, Inc. v. Barry, 891 F.3d 1368, 1380 (Fed. Cir. 2018). slip op. at 69

  Patent outcomesUS 10,556,381 unpatentable
  § 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,556,381
• Shenzhen Tuozhu Technology Co., Ltd. v. Stratasys, Inc.All claims unpatentable
  PTAB · Sep 28, 2026 · IPR2025-00611 · APJ Christopher L Ogden · IPR · Final written decision

  Claims 1–10, 12, 13, 19, and 20 are unpatentable under § 103 over the stated Douglas–Mark and Hamilton-based grounds.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “The parties agree that experience could substitute for a degree, and vice versa. Pet. 3; PO Resp. 10. The parties’ proposed levels of ordinary skill are substantially similar. For this decision, as in the Institution Decision, we adopt Petitioner’s proposed level, which is supported by credible testimonial evidence and is consistent with the problems addressed in the ’774 patent. See Ex. 1001, 1:16–52. Our decision would be the same, however, if we were to adopt Patent Owner’s proposal.” slip op. at 7

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Other

    “Neither Petitioner nor Patent Owner argues that we need to construe any claim terms explicitly. See Pet. 2–3; PO Resp. 10. However, the parties contest two material claim-construction issues which we address below. To the extent that the parties’ positions depend on interpreting other claim language in a particular way, we discuss the relevant claim language below in the context of the parties’ arguments regarding the prior art.” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “We disagree with Patent Owner that a person of ordinary skill in the art would have understood that limitation 1.2 must be performed before limitations 1.3 or 1.4. See Ex. 1001, 35:21–24. See Interactive Gift Exp., Inc. v. Compuserve Inc., 256 F.3d 1323, 1342 (Fed. Cir. 2001) (“Unless the steps of a method actually recite an order, the steps are not ordinarily construed to require one.” (citing Loral Fairchild Corp. v. Sony Corp., 181 F.3d 1313, 1322 (Fed. Cir. 1999)). The evidence suggests that a “target printer” is any printer that is ultimately selected for fabricating the object, and such a printer could send its configuration information either before or after that determination is made in limitation 1.2. This interpretation does not render the word “target” meaningless. At some point, a printer must be determined to be the target printer, which is the one intended to ultimately fabricate the three-dimensional object. But the target printer still exists, and is capable of being queried, before that determination is made. We find the examples in the ’774 patent pertinent to this question. The ’774 patent states that “the target printer may include more than one printer.” Ex. 1001, 18:66–67. In discussing the step of “query target printer for properties 306” (Fig. 3A), the ’774 patent states that “[i]n one aspect, numerous queries are sent to numerous printers, e.g., for use in selecting one or more of the printers as the target printer.” Id. at 19:8–10. Alternatively, “the query is sent to a printer that is not necessarily the target printer as described herein, e.g., when the query or information received from a response to the query is used for the selection of the target printer.” Id. at 19:11–14. Importantly, the second embodiment states that the queried printer “is not necessarily the target printer,” suggesting that the queried printer could be the target printer even before it is determined to be such. Id. at 19:11–12 (emphasis added). Based on the evidence of record, a person of ordinary skill in the art would have understood that the “target printer” can be determined after the query recited in limitation 1.3 or the reception of configuration information recited in limitation 1.4. Thus, the evidence does not impose an ordering between limitations 1.2 and 1.3 or between limitations 1.2 and 1.4. The evidence also does not support Patent Owner’s argument that the two reverse-order examples in the ’774 patent are unclaimed embodiments.” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightMotivation foundDecided for petitioner

    “We disagree that Petitioner’s arguments are based on impermissible hindsight, because they are based on the disclosures in Douglas and Mark, and Petitioner has articulated a persuasive reason to combine those references without referring to the ’774 patent itself, as we discuss below. See In re McLaughlin, 443 F.2d 1392, 1395 (CCPA 1971) (an obvious rationale is not improper hindsight if it “takes into account only knowledge which was within the level of ordinary skill at the time the claimed invention was made and does not include knowledge gleaned only from applicant’s disclosure”).” slip op. at 29

  Patent outcomesUS 11,886,774 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 11,886,774
• Shenzhen Tuozhu Technology Co., Ltd. v. Stratasys, Inc.Some claims unpatentable
  PTAB · Sep 28, 2026 · IPR2025-00531 · APJ Hyun J Jung · IPR · Final written decision

  Claims 1–11 and 13–15 are unpatentable over the stated obviousness grounds; claim 12 was not shown unpatentable.

  RulingsFinal written decision

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted

    “Petitioner filed a Petition (Paper 2, “Pet.”) requesting institution of an inter partes review of claims 1–15 of the ’698 patent. Discretionary denial of institution was determined to be not appropriate in this proceeding, and the proceeding was referred to the Board. Paper 10. Pursuant to 35 U.S.C. § 314, we instituted an inter partes review of claims 1–15 of the ’698 patent on all presented challenges. Paper 11 (“Inst. Dec.”), 15.” slip op. at 2

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableNot shown unpatentableMixed

    “Decision is issued pursuant to 35 U.S.C. § 318(a) and 37 C.F.R. § 42.73 (2025). For the reasons that follow, we determine that Shenzhen Tuozhu Technology Co., Ltd. (“Petitioner”) has shown by a preponderance of the evidence that claims 1–11 and 13–15, but not claim 12, of U.S. Patent No. 9,168,698 B2 (Ex. 1001, “the ’698 patent”) are unpatentable.” slip op. at 2

  Patent outcomesUS 9,168,698 mixed
  § 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,168,698
• Shenzhen Root Technology Co., Ltd. v. Willow Blossom Holdco Limited And Willow Innovations, Inc.All claims unpatentable
  PTAB · Sep 25, 2026 · IPR2025-00554 · APJ Barry L Grossman · IPR · Final written decision

  Claims 17–19 and 21–33 are unpatentable as obvious under each asserted § 103 ground.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Factors pertinent to a determination of the level of ordinary skill in the art include: (1) educational level of the inventor; (2) type of problems encountered in the art; (3) prior art solutions to those problems; (4) rapidity with which innovations are made; (5) sophistication of the technology; and (6) educational level of workers active in the field. Env’t Designs, Ltd. v. Union Oil Co., 713 F.2d 693, 696–697 (Fed. Cir. 1983) (citing Orthopedic Equip. Co. v. All Orthopedic Appliances, Inc., 707 F.2d 1376, 1381–82 (Fed. Cir. 1983)). Not all such factors may be present in every case, and one or more of these or other factors may predominate in a particular case. Id. Moreover, these factors are not exhaustive but are merely a guide to determining the level of ordinary skill in the art. Daiichi Sankyo Co. v. Apotex, Inc., 501 F.3d 1254, 1256 (Fed. Cir. 2007). In determining a level of ordinary skill, we also may look to the prior art, which may reflect an appropriate skill level. Okajima, 261 F.3d at 1355.” slip op. at 17

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “according to the Phillips standard,” and that “no formal claim constructions are necessary for purposes of resolving controversies in this proceeding. Pet. 3. We agree. Given the lack of dispute on this record, we do not perceive the need to construe any claim limitation. Claims must be construed “only to the extent necessary to resolve the controversy.” AstraZeneca AB v. Mylan Pharms. Inc., 19 F.4th 1325, 1345 (Fed. Cir. 2021) (quoting Vivid Techs., Inc. v. American Science & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“Because we need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy,’ we need not construe the claim preambles here where the construction is not ‘material to the [obviousness] dispute.’” (citations omitted)).” slip op. at 18

  • Expert testimonyPetitioner expert creditedDecided for petitioner

    “We find Mr. Bauer’s testimonial evidence persuasive and undisputed as to why a person of ordinary skill, a degreed engineer with two years of experience designing human breast pump equipment, would modify Furrer to use a battery as a power source, and have a reasonable degree of confidence that it would work successfully.” slip op. at 26

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner

    “We find Mr. Bauer’s testimonial evidence persuasive and undisputed as to why a person of ordinary skill, a degreed engineer with two years of experience designing human breast pump equipment, would modify Furrer to use a battery as a power source, and have a reasonable degree of confidence that it would work successfully. Concerning the proposed combination of Furrer and Alvarez, Mr. Bauer testifies why a person of ordinary skill would combine Furrer and Alvarez, explaining that: a POSITA6 would have turned to the teachings of Alvarez to implement Furrer’s vacuum pump using a conventional pump controller having a portable, battery-powered pump to not only increase portability and to allow the user to move about when using the device but also to provide improved control for the system. Ex. 1003 ¶ 138. Mr. Bauer also testifies: a POSITA would have recognized that Alvarez advantageously provides details for such a conventional vacuum pump suitable for safely and controllably delivering negative pressure using a “[c]ontroller 115 [that] “houses the power source and drive mechanism for pumping device 100, and also contains hardware for various functions, such as controlling pumping device 100, milk production quantification, and communication with other devices. 6 “POSITA” is a patent law acronym for a “person of ordinary skill in the art.” Id. ¶ 139 (citing Ex. 1005 ¶ 69). Mr. Bauer further explains that Alvarez discloses that a “pump unit2100 [disclosed in Alvarez] preferably include[es] a controller and processor 2104 as well as a motor 2102 for actuating the device.” Id. (citing Ex. 1005 ¶ 115); see also id. ¶¶ 140–142 (providing “second,” “third,” and “fourth” reasons why a person of ordinary skill would have been motivated to combine Furrer and Alvarez). Mr. Bauer concludes from his analysis that “a person skilled in the art” slip op. at 26

  Patent outcomesUS 11,806,454 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 11,806,454
• Shenzhen Root Technology Co., Ltd. v. Willow Blossom Holdco LimitedAll claims unpatentable
  PTAB · Jul 30, 2026 · IPR2025-00560 · APJ Barry L Grossman · IPR · Final written decision

  Claims 1–29 are unpatentable under each asserted obviousness ground, including Chang and Fang, because Petitioner proved unpatentability by a preponderance of the evidence.

  RulingsFinal written decision

  • Expert testimonyPetitioner expert creditedDecided for petitioner

    “Additionally, we note that Patent Owner did not cross-examine Mr. Ryan Bauer, who provided a detailed, 169-page expert report providing, on behalf of Petitioner, his opinions about the issues in this proceeding. See Exhibit 1003. Mr. Bauer’s testimonial evidence in this proceeding remains unrebutted.” slip op. at 3

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner asserts that a person of ordinary skill in the art would have had “bachelor’s degree in mechanical engineering or a similar field and at least two years of experience designing human breast pump equipment. More education could substitute for experience and vice versa.” Pet. 8 (citing Ex. 1003 ¶¶ 15–18). Mr. Bauer’s Declaration testimony states he considered some of the factors listed above. Ex. 1003 ¶ 17. Mr. Bauer testifies that based on his background and experience, in his opinion, the level of ordinary skill is as stated by Petitioner. Id. at 18. Based on the prior art, the sophistication of the disclosed technology in the ’381 patent, and Mr. Bauer’s undisputed testimony, we adopt Petitioner’s definition of the level of ordinary skill.” slip op. at 17

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner asserts that the Examiner construed the term “self- contained, in-bra wearable device” to mean “complete, or having all that is needed, in itself’ and is capable of being worn in a bra.” Pet. 8 (citing Ex. 1005, 2290).14 According to Petitioner, “[Patent Owner] did not dispute this construction, and Petitioner applies it herein.” Id. Petitioner contends that all other terms “should receive their plain and ordinary meaning.” Id. We do not perceive the need to construe any claim limitation. Claims must be construed “only to the extent necessary to resolve the controversy.” AstraZeneca AB v. Mylan Pharms. Inc., 19 F.4th 1325, 1345 (Fed. Cir. 2021) (quoting Vivid Techs., Inc. v. American Science & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“Because we need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy,’ we need not construe the claim preambles here where the construction is not ‘material to the [obviousness] dispute.’” (citations omitted)).” slip op. at 17

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “(3) 1[a][1] a diaphragm configured to prevent milk from reaching an air pump by forming a seal around its outer edge; Petitioner relies on Fang for the disclosure of a diaphragm, as stated in this clause. Pet. 25–26. Petitioner asserts the proposed combination of elements suggest a breast pump device that would have used a diaphragm pump including first and second diaphragm housing components and an elastic diaphragm, “in accordance with Fang’s suggestions.” Id. at 25. As also asserted by Petitioner, Fang discloses that flexible diaphragm 7 (i.e., a membrane) is configured to prevent milk from reaching the pump. Id. at 26 (citing Ex. 1009 ¶ 19 (“The elastic diaphragm 7 is used to prevent milk from flowing into the air pump main unit 8.”). Mr. Bauer testifies: The flexible diaphragm [diaphragm 7 in Fang] forms a watertight and airtight seal around its outer edge. In doing so, the diaphragm prevents the passage of milk from reaching the air pump and facilitates generation of negative pressure during operation. Fang also explains that the elastic diaphragm 7 deforms away from the nipple tunnel when a vacuum is created on a pumping chamber, which then creates negative air pressure in the nipple tunnel when a vacuum is created on a pumping chamber.” slip op. at 28

  Patent outcomesUS 11,813,381 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 11,813,381
• Samsung Display Co., Ltd. v. Pictiva Displays International Ltd.All claims unpatentable
  PTAB · Jul 22, 2026 · IPR2024-01095 · APJ Garth D Baer · IPR · Remand

  On remand, the Board maintained its finding that claims 2 and 17 are unpatentable under §103 over Diekmann and Ma, and Suzuki and Ma.

  RulingsRemand decision

  • RemandDecided for petitioner

    “that is both n-doped and comprised of 8-hydroxy-quinolinolato-lithium (Liq). The district-court defendant’s first invalidity challenge relied primarily on Clix2, which lacked an n-doped ETL. Paper 48, 2, Paper 50, 3. Thus, the asserted combination required modifying Clix2’s non-doped ETL by adding an n-dopant. Clix2’s missing n-doped ETL appeared to be a focus at trial. See Ex. 2034, 917:1–18, 920:8–14. Here, in contrast, Petitioner proposed a more modest modification to materially different primary references, Suzuki and Diekmann, which both already have n-doped ETLs. See Paper 50, 2–3; Paper 54 8–9. As we explained in our Final Written Decision, because Patent Owner did not contest that Liq acts as an n-dopant in Ma, Petitioner’s combinations were obvious because they merely “substitute one known n-dopant for another to further the same goal of improving ETL conductivity.” Paper 54, 12. That simple-substitution analysis would not be the same when n-doping Clix2’s non-doped ETL. For this reason, we agree with Petitioner that the district-court Clix2-based combination “is a different combination with a materially different motivation-to-combine analysis,” as compared to the Diekmann/Suzuki and Ma combinations that are at issue here. Paper 50, 3.” slip op. at 2

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “Dependent claims 2 and 17 require an electron transport layer (ETL) that is both n-doped and comprised of 8-hydroxy-quinolinolato-lithium (Liq). The district-court defendant’s first invalidity challenge relied primarily on Clix2, which lacked an n-doped ETL. Paper 48, 2, Paper 50, 3. Thus, the asserted combination required modifying Clix2’s non-doped ETL by adding an n-dopant. Clix2’s missing n-doped ETL appeared to be a focus at trial. See Ex. 2034, 917:1–18, 920:8–14. Here, in contrast, Petitioner proposed a more modest modification to materially different primary references, Suzuki and Diekmann, which both already have n-doped ETLs. See Paper 50, 2–3; Paper 54 8–9. As we explained in our Final Written Decision, because Patent Owner did not contest that Liq acts as an n-dopant in Ma, Petitioner’s combinations were obvious because they merely “substitute one known n-dopant for another to further the same goal of improving ETL conductivity.” Paper 54, 12. That simple-substitution analysis would not be the same when n-doping Clix2’s non-doped ETL. For this reason, we agree with Petitioner that the district-court Clix2-based combination “is a different combination with a materially different motivation-to-combine analysis,” as compared to the Diekmann/Suzuki and Ma combinations that are at issue here. Paper 50, 3.” slip op. at 2

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable

    “that is both n-doped and comprised of 8-hydroxy-quinolinolato-lithium (Liq). The district-court defendant’s first invalidity challenge relied primarily on Clix2, which lacked an n-doped ETL. Paper 48, 2, Paper 50, 3. Thus, the asserted combination required modifying Clix2’s non-doped ETL by adding an n-dopant. Clix2’s missing n-doped ETL appeared to be a focus at trial. See Ex. 2034, 917:1–18, 920:8–14. Here, in contrast, Petitioner proposed a more modest modification to materially different primary references, Suzuki and Diekmann, which both already have n-doped ETLs. See Paper 50, 2–3; Paper 54 8–9. As we explained in our Final Written Decision, because Patent Owner did not contest that Liq acts as an n-dopant in Ma, Petitioner’s combinations were obvious because they merely “substitute one known n-dopant for another to further the same goal of improving ETL conductivity.” Paper 54, 12. That simple-substitution analysis would not be the same when n-doping Clix2’s non-doped ETL. For this reason, we agree with Petitioner that the district-court Clix2-based combination “is a different combination with a materially different motivation-to-combine analysis,” as compared to the Diekmann/Suzuki and Ma combinations that are at issue here. Paper 50, 3.” slip op. at 2

  Patent outcomesUS 11,828,425 unpatentable
  § 103 obviousness
  Patents in suitUS 11,828,425
• Posco Co., Ltd. v. ArcelormittalAll claims unpatentable
  PTAB · Jul 16, 2026 · IPR2025-00371 · APJ Brian D Range · IPR · Final written decision

  Claims 1–25 are unpatentable as obvious under § 103 over the asserted combinations of Takagi, Cornette, Suehiro, GMW14400, Laurent, and Vaissiere.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art (POSITA) “would have had an undergraduate degree in materials science, manufacturing engineering, mechanical engineering, or equivalent knowledge, training, or experience, with two years of experience working in metallurgy.” Pet. 6 (citing Ex. 1003 ¶ 15). Patent Owner does not challenge Petitioner’s definition of a POSITA for this proceeding. PO Resp. 8. Because the parties agree and because Petitioner’s proposal is reasonable and consistent with the ’227 patent specification and the prior art, we adopt Petitioner’s proposal. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art).” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for patent owner

    “1. superficial layer The only independent claim at issue, claim 1, recites a “Superficial layer.” Ex. 1001, 15:6. Patent Owner argues that, based on plain and ordinary meaning, the term “superficial layer” refers to a “surface layer” or “top layer.” PO Resp. 8–9. Petitioner does not dispute this construction. See Pet. Reply 21–22 (arguing that the relevant layer of the Suehiro reference is a superficial layer because it is outermost and present at the surface). Because the parties are in agreement and because that agreement is consistent with plain language, claim language, and the ’227 specification, we construe “superficial layer” as referring to a surface layer or top layer.” slip op. at 10

  • Claim Construction › Extrinsic evidence (dictionaries, experts)Term construed petitioner constructionDecided for petitioner

    “defined stoichiometry” (Ex. 2037, 527) but the word may also be a “generic term for phases . . . which may have a narrow or extended compositional stability range” (id.). The first glossary meaning is consistent with Patent Owner’s position. The second, broader, glossary meaning is consistent with Petitioner’s position. Some of the extrinsic sources before us support the broad definition, and some support the narrow definition. See PO Sur-Reply 3–4 (arguing that Dr. Miles admitted that various treatises distinguish intermetallic compounds from alloys and solid solutions). Thus, neither Dr. Miles or Dr. Raabe is “wrong scientifically” in how they use the term “intermetallic” in this proceeding. Id. at 2 (noting that Dr. Miles agreed that Dr. Raabe’s construction is not wrong scientifically). As explained below, however, only one of these meanings is appropriate here. To decide which possible meaning applies to the ’227 patent, we focus on the patent claims and specification. Claim 1 indicates that the intermetallic layer has a “mean composition” (emphasis added). Ex. 1001, 15:1–10. This indicates, albeit weakly, that iron composition across the layer may vary rather than having ordered stoichiometry—consistent with Petitioner’s position. The specification also indicates that “intermetallic alloying” is a possibility—again, consistent with Petitioner’s position. Ex. 1001, 2:47–50. Meanwhile, nothing in the ’227 specification explicitly (or implicitly) suggests that “intermetallic layer” must be limited to elements atomically joined with defined stoichiometry in an ordered crystal structure. We also find that Dr. Miles’s testimony regarding the meaning of “intermetallic” is more credible than Dr. Rabbe’s testimony. Dr. Rabbe, in deposition, stated that Figure 2 of the challenged patent “does not show a layer that meets [his] construction of intermetallic.” Ex. 1078, 129:21–24. The ’227 patent, however, states that Figure 2 includes an “Al-rich Intermetallic layer.” Ex. 1001, Fig. 2, 3:60–64 (“FIG 2. Illustrates a coating … which does not correspond to the invention. This succession of layers (interdiffusion layer and intermetallic layer) yields inferior results in resistance spot welding.”). Also, Dr. Raabe previously referred to a layer of Takagi as having “intermetallic phase layering and structure.” Pet. Reply 4 (citing Ex. 1076 ¶ 166; Ex ¶ 1075, 17) (emphasis omitted). Thus, Dr. Raabe’s construction of “intermetallic” for this proceeding does not fully account for the ’227 patent usage of the word “intermetallic” and does not fully account for Dr. Raabe’s prior usage of the word “intermetallic.” Patent Owner argues that Petitioner’s construction “erases the meaningful distinction” between the claimed layers. PO Resp. 11. Patent Owner further argues that Petitioner’s construction renders the word “intermetallic” superfluous because allowing the intermetallic layer to be “merely a multi-element alloy erases the meaningful distinction among these layers.” Id. We disagree. The word intermetallic serves to require that the layer be composed of two or more metals or a metal and a metalloid. The word intermetallic also serves as a label to differentiate each of the four claimed layers. For example, in claim 1, the word “intermetallic” is used much like the words “interdiffusion” and “intermediate” to give each of the four layers (each having differently mean compositions) different labels.” slip op. at 16

  • Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication establishedDecided for petitioner

    “Because IHS was a company that created an online database with the purpose of providing (selling) standards including General Motors standards to the public, we determine that a person of ordinary skill in the art would have known to look to this database and would have been able to find GMW14400. Patent Owner presents no evidence to the contrary. Because a preponderance of the evidence supports Petitioner, we determine Petitioner establishes GMW14400 is qualifies as prior art.” slip op. at 21

  Patent outcomesUS 11,326,227 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,326,227
• Posco Co., Ltd. v. ArcelormittalAll claims unpatentable
  PTAB · Jul 16, 2026 · IPR2025-00370 · APJ Brian D Range · IPR · Final written decision

  Claims 1–30 are unpatentable as obvious under § 103 over the asserted combinations of prior art.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art (POSITA) “would have had an undergraduate degree in materials science, manufacturing engineering, mechanical engineering, or equivalent knowledge, training, or experience, with two years of experience working in metallurgy.” Pet. 6 (citing Ex. 1003 ¶¶ 13–16). Patent Owner does not challenge Petitioner’s definition of a POSITA for this proceeding. PO Resp. 8. Because the parties agree and because Petitioner’s proposal is reasonable and consistent with the ’602 patent specification and the prior art, we adopt Petitioner’s proposal. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art).” slip op. at 8

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

    “1. superficial layer All independent claims at issue, claims 1, 21, and 24, recite a “superficial layer.” Ex. 1001, 15:11, 16:60, 17:21. Patent Owner argues that, based on plain and ordinary meaning, the term “superficial layer” refers to a “surface layer” or “top layer.” PO Resp. 8–9. Petitioner does not dispute this construction. See Pet. Reply 21–22 (arguing that the relevant layer of the Suehiro reference is a superficial layer because it is outermost and present at the surface). Because the parties are in agreement and because that agreement is consistent with plain language, claim language, and the ’602 specification, we construe “superficial layer” as referring to a surface layer or top layer.” slip op. at 10

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “defined stoichiometry” (Ex. 2037, 527) but the word may also be a “generic term for phases . . . which may have a narrow or extended compositional stability range” (id.). The first glossary meaning is consistent with Patent Owner’s position. The second, broader, glossary meaning is consistent with Petitioner’s position. Some of the sources before us support the broad definition, and some support the narrow definition. See PO Sur-Reply 3–4 (arguing that Dr. Miles admitted that various treatises distinguish intermetallic compounds from alloys and solid solutions) Thus, neither Dr. Miles or Dr. Raabe is “wrong scientifically” in how they use the term “intermetallic” in this proceeding. Id. at 2 (noting that Dr. Miles agreed that Dr. Raabe’s construction is not wrong scientifically). As explained below, however, only one of these meanings is appropriate here. To decide which possible meaning applies to the ’602 patent, we focus on the patent claims and specification. The claims indicate that the intermetallic layer has a “mean iron composition” (emphasis added). Ex. 1001, 15:6–10. This indicates, albeit weakly, that the iron composition across the layer may vary rather than having ordered stoichiometry— consistent with Petitioner’s position. The specification also indicates that “intermetallic alloying” is a possibility—again, consistent with Petitioner’s position. Id. at 2:50–54. Meanwhile, nothing in the ’602 specification explicitly (or implicitly) suggests that “intermetallic layer” must be limited to elements atomically joined with defined stoichiometry in an ordered crystal structure. We also find that Dr. Miles’s testimony regarding the meaning of “intermetallic” is more credible than Dr. Raabe’s testimony. Dr. Raabe, in deposition, stated that Figure 2 of the challenged patent “does not show a layer that meets [his] construction of intermetallic.” Ex. 1078, 129:21–24. The ’602 patent, however, states that Figure 2 includes an “Al-rich Intermetallic layer.” Ex. 1001, Fig. 2, 3:57–61 (“FIG 2. Illustrates a coating . . . which does not correspond to the invention. This succession of layers (interdiffusion layer and intermetallic layer) yields inferior results in resistance spot welding.”). Also, Dr. Raabe previously referred to a layer of Takagi as having “intermetallic phase layering and structure.” Pet. Reply 4 (citing Ex. 1076, 166; Ex. 1075, 17) (emphasis omitted). Thus, Dr. Raabe’s definition of “intermetallic” does not fully account for the ’602 patent usage of the word “intermetallic” and does not fully account for Dr. Raabe’s prior usage of the word “intermetallic.” Patent Owner argues that Petitioner’s construction “erases the meaningful distinction” between the claimed layers. PO Resp. 11. Patent Owner further argues that Petitioner’s construction renders the word “intermetallic” superfluous because allowing the intermetallic layer to be “merely a multi-element alloy erases the meaningful distinction among these layers.” Id. We disagree. The word intermetallic serves to require that the layer be composed of two or more metals or a metal and a metalloid. The word intermetallic also serves as a label to differentiate each of the four claimed layers. For example, in claim 1, the word “intermetallic” is used much like the words “interdiffusion” and “intermediate” to give each of the four layers (each having differently defined mean iron compositions) different labels.” slip op. at 16

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner

    “have had reason to combine teachings of Takagi and Cornette with a reasonable expectation of success. Pet. 11–20 (citing, e.g., Ex. 1003 ¶¶ 28– 42; Ex. 1016 ¶ 35; Ex. 1014, 9; Ex. 1025, 5:17–20; Ex. 1026, 7; Ex. 1034 ¶ 13). In particular, Petitioner argues that Takagi discloses a pre-coating thickness of 10–20 µm but does not explicitly disclose a post hot-stamping coating thickness corresponding to the pre-coating thickness. Pet. 11. Cornette teaches that the hot-stamping thickness causes coating expansion from 25 µm to about 40 µm, an increase of 60%. Id. (citations omitted). Petitioner and Dr. Miles reason that, when hot stamping Takagi’s product, the thickness would be 32 µm. Id. (citing Ex. 1003 ¶ 32); see also Pet. Reply 20–21. Thus, Patent Owner argues that Cornette evidences Takagi’s finally coating thickness without requiring modification of Takagi. Petitioner further argues that Takagi and Cornette teach that post hot- stamping thickness could be varied and optimized as a result effective variable. Id. at 12–13; see also Pet. Reply 17–18. Cornette teaches, for example, that “[t]he average [pre-coating] layer thickness showing the best compromise between corrosion protection and weldability is 25 µm” and links this pre-coating thickness to a final thickness of “about 40 µm at the steel surface.” Ex. 1014, 9. Petitioner also argues that it would have been obvious to fill in other details of Takagi including, for example, selecting USIBOR 1500 steel, based on the teachings of Cornette. Pet. 14. Patent Owner argues that there is no reason to combine Takagi with the teachings of Cornette. PO Resp. 26. Patent Owner makes seven related arguments. Patent Owner first argues that the Petitioner’s position is speculative and lacks basis. Id. at 26–27. We disagree. Cornette evidences a final coating thickness for Takagi, and the references also suggest that final coating thickness is result effective. Second, Patent Owner argues that there would have been no incentive to seek a motivation to seek a thicker coating post-hot stamping. Id. at 28– 35. This argument does not undermine Petitioner’s position that Takagi, by itself, would have reached a thicker coating after stamping as evidenced by Cornette. Pet. 11–12. Petitioner takes the position, with evidence, that practice of Takagi alone would reach the recited thickness. No motivation to modify Takagi is required under this position.” slip op. at 25

  Patent outcomesUS 10,961,602 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 10,961,602

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.