• Guardant Health, Inc. v. University Of WashingtonNo claims unpatentable
  PTAB · Oct 14, 2026 · IPR2022-00817 · APJ Zhenyu Yang · IPR · Remand

  On remand, the Board found Travers ’075 did not enable RCR amplification followed by SMRT sequencing and held claims 1–30 not shown unpatentable under the asserted obviousness grounds.

  RulingsRemand decision

  • RemandOther

    “B. Scope on Remand On remand, we are bound by the terms of the Federal Circuit’s mandate. Intell. Pixels Ltd. v. Sony Interactive Ent. LLC, 181 F.4th 1216, 1220 (Fed. Cir. 2026) (“An administrative agency is bound by the mandate of a reviewing court much as a lower court is bound by the mandate of a higher court.”). According to the Federal Circuit, on appeal, Patent Owner “UW argues that ‘Travers ’075 does not enable the sequencing of an RCR concatemer using PacBio’s SMRT sequencing,’ and therefore because paragraph 122 is not enabled, it cannot be relied on for disclosing amplification followed by sequencing.” Paper 50, 14. Because “[t]he Board did not reach this issue,” the Federal Circuit “remand[ed] the case for consideration of this issue by the Board in the first instance.” Id. Thus, consistent with the court’s mandate, we must decide “whether Travers ’075 enabled RCR amplification followed by SMRT sequencing.” Id. at 8.” slip op. at 4

  • BurdenNot shown unpatentable

    “A prior art reference is presumed to be enabled. Amgen, Inc. v. Hoechst Marion Roussel, Inc., 314 F.3d 1313, 1355 (Fed. Cir. 2003) (holding that “a presumption arises that both the claimed and unclaimed disclosures in a prior art patent are enabled”); In re Antor Media Corp., 689 F.3d 1282, 1288 (Fed. Cir. 2012) (extending the presumption to prior art printed publications). A patent owner, however, may present persuasive evidence that the relevant disclosures of a prior art are not enabled and therefore are not pertinent prior art. Amgen, 314 F.3d at 1355; In re Antor Media, 689 F.3d at 1289 (discussing the applicant’s burden to submit rebuttal evidence of nonenablement during prosecution); Apple Inc. v. Corephotonics, Ltd., 861 Fed. App’x. 443, 450 (Fed. Cir. 2021) (“[R]egardless of the forum, prior art patents and publications enjoy a presumption of enablement, and the patentee/applicant has the burden to prove nonenablement for such prior art.”). “[T]here is no absolute requirement for a relied-upon reference to be self-enabling in the § 103 context, so long as the overall evidence of what was known at the time of invention establishes that a skilled artisan could have made and used the claimed invention.” Raytheon Techs. Corp. v. Gen. Elec. Co., 993 F.3d 1374, 1376–77 (Fed. Cir. 2021). But, “if an obviousness case is based on a non-self-enabled reference, and no other prior art reference or evidence would have enabled a skilled artisan to make the claimed invention, then the invention cannot be said to have been obvious.” Id. at 1377.” slip op. at 15

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successNot reached

    “The Federal Circuit stated that “the elements of the challenged claim are expressly taught by Travers ’075. Travers ’075 discloses performing RCR amplification followed by SMRT sequencing in a single embodiment.” Paper 50, 14. As a result, “no finding regarding a motivation to combine to arrive at those claimed elements is required.” Id. at 9. In addition, it was error to require Petitioner to show that a skilled artisan “would have had a reasonable expectation of success in performing RCR replication of SMRTbell templates followed by SMRT sequencing.” Id. at 13. “Unless remanded by [an appellate] court, all issues within the scope of the appealed judgment are deemed incorporated within the mandate and thus are precluded from further adjudication.” Engel Indus., Inc. v. Lockformer Co., 166 F.3d 1379, 1383 (Fed. Cir. 1999). Therefore, the only issue for us to decide is “whether Travers ’075 enabled RCR amplification followed by SMRT sequencing.” Paper 50, 8.” slip op. at 14

  • Expert testimonyPatent owner expert creditedDecided for patent owner

    “polymerase-template complexes in the same ZMW.” Id. (citing Ex. 1035, 39). Citing the Larrea Declaration, Petitioner contends that loading of multiple templates “is easily mitigated.” Id. at 18 (citing Ex. 1033 ¶ 19; Ex. 1035, 39). We are not persuaded by this argument either. Dr. Larrea testifies that one of the two methods to “easily mitigate[]” loading multiple templates into a single ZMW is “bioinformatically trimming the read to only the high-quality region (HQR).” Ex. 1033 ¶ 19. Dr. Larrea, however, provides no support for this testimony. In fact, he does not even explain what a “high-quality region (HQR)” is. We, thus, accord little weight to this testimony. See Xerox Corp. v. Bytemark, Inc., IPR2022-00624, Paper 9 (August 24, 2022) (precedential) (holding “conclusory and unsupported” declaration testimony is entitled to little weight).” slip op. at 26

  Patent outcomesUS 10,760,127 not shown unpatentable
  § 103 obviousness
  Patents in suitUS 10,760,127
• Uatp IP LLC v. Slick Slide LLCSome claims unpatentable
  PTAB · Oct 2, 2026 · PGR2024-00054 · APJ Brian D Range · PGR · Final written decision

  Claims 22–26 are unpatentable based on obviousness; claims 1–17, 27, and 28 were not shown unpatentable. Patent Owner’s motion to terminate was denied.

  RulingsFinal written decision

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed board ownDecided for patent owner

    “1. Mesh Layer Petitioner contends “no formal claim construction is necessary in this” slip op. at 13

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

    “5. Analysis On this complete record, we determine that Petitioner’s arguments do” slip op. at 31

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable

    “form of nylon and some form of Teflon (and possible combinations thereof) having the specific coefficient of friction range given in limitation [1c] breaks down, because the building blocks of the obviousness argument are not sufficiently identified in Phillips alone, nor in the supporting testimony. Accordingly, we determine that Petitioner’s arguments and evidence fail to show that Phillips renders the challenged claims obvious. 6. Conclusion Based on the foregoing, we determine that Petitioner has not established by a preponderance of the evidence that claims 1–4, 6, and 7 would have been anticipated by or obvious in view of Phillips.” slip op. at 33

  • Obviousness (§103) › Objective indicia / secondary considerations › NexusObjective indicia no nexusDecided for petitioner

    “2. Products and Nexus We first consider the issue of whether certain evidence relied upon by” slip op. at 20

  Patent outcomesUS 11,998,854 mixed
  Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · Graham · Nautilus
  Patents in suitUS 11,998,854
• Shenzhen Tuozhu Technology Co., Ltd. v. Stratasys, Inc.All claims unpatentable
  PTAB · Sep 28, 2026 · IPR2025-00611 · APJ Christopher L Ogden · IPR · Final written decision

  Claims 1–10, 12, 13, 19, and 20 are unpatentable under § 103 over the stated Douglas–Mark and Hamilton-based grounds.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “The parties agree that experience could substitute for a degree, and vice versa. Pet. 3; PO Resp. 10. The parties’ proposed levels of ordinary skill are substantially similar. For this decision, as in the Institution Decision, we adopt Petitioner’s proposed level, which is supported by credible testimonial evidence and is consistent with the problems addressed in the ’774 patent. See Ex. 1001, 1:16–52. Our decision would be the same, however, if we were to adopt Patent Owner’s proposal.” slip op. at 7

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Other

    “Neither Petitioner nor Patent Owner argues that we need to construe any claim terms explicitly. See Pet. 2–3; PO Resp. 10. However, the parties contest two material claim-construction issues which we address below. To the extent that the parties’ positions depend on interpreting other claim language in a particular way, we discuss the relevant claim language below in the context of the parties’ arguments regarding the prior art.” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “We disagree with Patent Owner that a person of ordinary skill in the art would have understood that limitation 1.2 must be performed before limitations 1.3 or 1.4. See Ex. 1001, 35:21–24. See Interactive Gift Exp., Inc. v. Compuserve Inc., 256 F.3d 1323, 1342 (Fed. Cir. 2001) (“Unless the steps of a method actually recite an order, the steps are not ordinarily construed to require one.” (citing Loral Fairchild Corp. v. Sony Corp., 181 F.3d 1313, 1322 (Fed. Cir. 1999)). The evidence suggests that a “target printer” is any printer that is ultimately selected for fabricating the object, and such a printer could send its configuration information either before or after that determination is made in limitation 1.2. This interpretation does not render the word “target” meaningless. At some point, a printer must be determined to be the target printer, which is the one intended to ultimately fabricate the three-dimensional object. But the target printer still exists, and is capable of being queried, before that determination is made. We find the examples in the ’774 patent pertinent to this question. The ’774 patent states that “the target printer may include more than one printer.” Ex. 1001, 18:66–67. In discussing the step of “query target printer for properties 306” (Fig. 3A), the ’774 patent states that “[i]n one aspect, numerous queries are sent to numerous printers, e.g., for use in selecting one or more of the printers as the target printer.” Id. at 19:8–10. Alternatively, “the query is sent to a printer that is not necessarily the target printer as described herein, e.g., when the query or information received from a response to the query is used for the selection of the target printer.” Id. at 19:11–14. Importantly, the second embodiment states that the queried printer “is not necessarily the target printer,” suggesting that the queried printer could be the target printer even before it is determined to be such. Id. at 19:11–12 (emphasis added). Based on the evidence of record, a person of ordinary skill in the art would have understood that the “target printer” can be determined after the query recited in limitation 1.3 or the reception of configuration information recited in limitation 1.4. Thus, the evidence does not impose an ordering between limitations 1.2 and 1.3 or between limitations 1.2 and 1.4. The evidence also does not support Patent Owner’s argument that the two reverse-order examples in the ’774 patent are unclaimed embodiments.” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightMotivation foundDecided for petitioner

    “We disagree that Petitioner’s arguments are based on impermissible hindsight, because they are based on the disclosures in Douglas and Mark, and Petitioner has articulated a persuasive reason to combine those references without referring to the ’774 patent itself, as we discuss below. See In re McLaughlin, 443 F.2d 1392, 1395 (CCPA 1971) (an obvious rationale is not improper hindsight if it “takes into account only knowledge which was within the level of ordinary skill at the time the claimed invention was made and does not include knowledge gleaned only from applicant’s disclosure”).” slip op. at 29

  Patent outcomesUS 11,886,774 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 11,886,774
• Clearwater Paper Corporation v. Graphic Packaging International LLCAll claims unpatentable
  PTAB · Sep 23, 2026 · IPR2025-00878 · APJ Carl M Defranco · IPR · Final written decision

  Claims 1–3 and 11 are unpatentable as anticipated by Cleveland and obvious over Nakagawa and over Nakagawa combined with Tanner.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “would have at least a bachelor’s degree in mechanical or chemical engineering, materials science, polymer science, or equivalent coursework, at least a year of experience developing paper-based laminates involving the application of polymer coatings to a substrate, and the appropriate industry familiarity with biodegradability standards and degradability techniques [and] . . . [l]ess work experience may be compensated by a higher level of education, such as a master’s degree, and vice versa. Pet. 16 (citing Ex. 1003 ¶ 50). Clearwater’s definition is uncontested, and we apply that definition here, as it accords with the level of skill reflected in the asserted prior art and the problems addressed in the specification of the ’126 patent. C. Claim Construction” slip op. at 6

  • Expert testimonyPetitioner expert creditedDecided for petitioner

    “We have reviewed the cited testimony of Clearwater’s expert, including their calculations for arriving at a coat weight in Nakagawa that falls within the claimed range. See Ex. 1003 ¶¶ 132–33. We find that testimony, which is unrebutted, both credible and supported by the evidence of record. Thus, in light of Clearwater’s contentions, the cited portions of Nakagawa, and the unrebutted testimony of Clearwater’s expert, we are persuaded that Nakagawa discloses or otherwise suggests each and every element of claim 1. See Pet. 45–54, 60–64. Clearwater also persuades us that Cleveland discloses the additional subject matter of dependent claims 2, 3, and 11. See Pet. 64–66. Thus, we determine that Clearwater demonstrates that claims 1–3 and 11 are unpatentable as obvious over Nakagawa. F. Ground 3—Obviousness Over Nakagawa and Tanner” slip op. at 17

  • Novelty / Anticipation (§102) › Prior-art status of a reference › Patents / published applications (effective date, provisional support)Reference is prior artDecided for petitioner

    “qualifies as prior art under 35 U.S.C. § 102(e)(1) “based on both its provisional and non-provisional filing dates.” Inst. Dec. 4 n.5. We were persuaded by Clearwater’s proof that Cleveland’s provisional (Ex. 1006) is “virtually identical” to Cleveland itself (Ex. 1005) and that the provisional provides written description support for at least claim 1 of Cleveland. See Pet. 18–21 (citing Ex. 1006, 2–6, 9). We were also persuaded by Clearwater’s showing that the provisional provides written support for the subject matter relied upon in Cleveland. Id. at 21–40 (citing Ex. 1006, 1–9). We are still persuaded by Clearwater’s showing. Thus, we see no reason to disturb our earlier finding that Cleveland is prior art to the ’126 patent.” slip op. at 7

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

    “protectant layers has “a coat weight of from 5 to 30 lbs/3000 ft2.” As noted by Clearwater, Cleveland discloses a total coat weight for layers 14 and 16 as falling within the claimed range. Pet. 32–34 (citing Ex. 1005 ¶ 32). In particular, Cleveland discloses that “the coextruded layer of copolyester (irrespective of which side of the substrate the layer is disposed) is of a total coat weight of between about 10 and about 40 lb/3000 ft2 in any combination of between about 80/20 to 20/80 parts by weight of Ecoflex to Biomax,” of which “a total coat weight of 25 lb/3000 ft2 is preferred.” Ex. 1005 ¶ 32. As disclosed, Cleveland’s total coat weight range of 10–40 lb/3000 ft2 falls almost entirely within the claimed range, and the preferred total coat weight of 25 lb/3000 ft2 falls squarely within the claimed range. Thus, Cleveland satisfies claim elements [1.3.2] and [1.5.2]. See Titanium Metals Corp. v. Banner, 778 F.2d 775, 782 (Fed. Cir. 1985) (“[W]hen, as by a recitation of ranges or otherwise, a claim covers several compositions, the claim is anticipated if one of them is in the prior art.”) (citation omitted). As such, we find that Clearwater adequately demonstrates that Cleveland discloses all the elements of claim 1. 4. Dependent Claims” slip op. at 12

  Patent outcomesUS 8,637,126 unpatentable
  § 102 anticipation§ 103 obviousnesscites Phillips
  Patents in suitUS 8,637,126
• Crowdstrike, Inc. v. Gosecure, Inc.Some claims unpatentable
  PTAB · Aug 12, 2026 · IPR2025-00070 · APJ Neil T Powell · IPR · Final written decision

  Claims 1, 3–7, and 9–21 are unpatentable as obvious; claims 2 and 8 were not shown unpatentable because the asserted art did not meet their construed limitations.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “III. ANALYSIS LEVEL OF ORDINARY SKILL A. Petitioner explains the applicable level of skill in the art as follows: As of June 24, 2010, a person of ordinary skill in the art (POSITA) would be a person having a bachelor’s degree in computer science, computer engineering, or an equivalent, as well as two years of industry experience and who would have had a working knowledge of software security analysis, and dynamic malware analysis. Additional graduate education could substitute for professional experience, or significant experience in the field could substitute for formal education. Pet. 8 (Ex. 1003 ¶¶ 30–31). Patent Owner does not dispute Petitioner’s explanation of the level of skill in the art. See Ex. 2031 ¶¶ 15–16. We adopt Petitioner’s uncontested proposed level of ordinary skill in the art, which we find consistent with the level of ordinary skill in the art reflected by the ’872 patent and the prior art of record. See Okajima v.” slip op. at 12

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “We begin with the claim language in view of the Specification, which weighs heavily against Patent Owner’s position that we should rewrite “computer system” as narrowly referring to a “computing device.” PO Resp. 24. As Petitioner notes, the ’872 patent’s Specification uses “computer system” to refer to a wide range of equipment, from a component of a computing device, to a whole computing device, to a collection of computing devices. Reply 9–10 (citing Ex. 1001, 4:5–8, 11:15–18, 16:50–55). In one example, the Specification refers to “one or more other computer systems (e.g., protected network devices 136).” Ex. 1001, 18:52–53. Thus, the Specification lists “protected network devices 136” as only an example of “other computer systems,” demonstrating that “computer systems” refers to things other than protected network devices. Although Patent Owner may be correct that this passage more than a single computing device,” we find that other disclosures in the ’872 patent do. Specifically, the Specification uses the language “distributed computer system” when referring to numerous components, including “protected network devices” and an “IDS/IPS system.” Ex. 1001, 3:26–28; Reply 10. In addition to showing that a “computer system” is not limited to a single computing device, this conveys that a “computer system” according to the ’872 patent can include an IDS/IPS.” slip op. at 14

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundDecided for petitioner

    “Based on our review of the complete record, we find Petitioner’s arguments and evidence to be more persuasive. Patent Owner does not dispute Petitioner’s argument and evidence that capturing detailed information like Goel’s activity sources, activity targets, and association was recognized as enhancing threat analysis. Pet. 44 (citing Ex. 1003 ¶ 79); see PO Resp. 55–59; Sur-Reply 15–17. Additionally, contrary to Patent Owner’s suggestion, we find that the Petition does not propose incorporating Goel’s kernel hooks into Capalik’s system. See Pet. 41–46. Patent Owner contends that the Petition’s reference to modifying Capalik by “adding lines of code” suggests implementing the code disclosed in Goel include kernel hooks. Id. Notwithstanding Patent Owner’s assertion otherwise, this is an unpersuasive bodily incorporation argument, as the Petition never says an ordinarily skilled artisan would have used the exact lines of code from Goel in Capalik. Rather, the Petition says that an ordinarily skilled artisan would have had sufficient skill to implement straightforward code modifications to identify activity sources, targets, and associations: a [person of ordinary skill in the art] would have understood that modifying Capalik’s system (e.g., Linux-based) to additionally monitor, identify, and store each individual activity of an attack including “activity sources, activity targets, and associations” would have required straightforward modifications to programs/code instructions, which would have been well-within the skillset of a [person of ordinary skill in the art]. Pet. 46. Patent Owner argues that Petitioner does not explain how an ordinarily skilled artisan would have modified Capalik without using kernel hooks. Sur-Reply 17. But Patent Owner does not cite any evidence to counter Dr. Jakobsson’s testimony that an ordinarily skilled artisan would have had the skill to apply Goel’s general teaching of identifying sources, targets, and associations to Capalik’s system. Ex. 1003 ¶ 182. On the whole, the evidence does not support Patent Owner’s position that the combination would have required substantially increased detection risk. Moreover, even if the combination would have somewhat increased detection risk, Petitioner persuades us that an ordinarily skilled artisan still would have had reason to combine the references teachings. Patent Owner’s allegations of increased detection risk do not negate the undisputed evidence that the combination would have provided the advantage of improved threat analysis. Pet. 44 (citing Ex. 1003 ¶¶ 175–182). Ultimately, Patent Owner’s that activity logging be undetectable.” PO Resp. 56 (emphasis added) (citing Ex. 1004 ¶ 6). This exaggerates Capalik’s disclosure. Although the cited paragraph suggests that certain systems unfortunately may be detectable by some users, it does not convey that it is a requirement for the system to be categorically undetectable. See Ex. 1004 ¶ 6.8 In sum, Petitioner persuades us by a preponderance of the evidence that it would have been obvious to modify Capalik “to identify and store unauthorized activities including the activity source, activity target, and association of each activity.” Pet. 41–46; PO Resp. 55–59; Reply 20–22; Sur-Reply 15–17.” slip op. at 47

  • Obviousness (§103) › Objective indicia / secondary considerations › NexusObjective indicia no nexusDecided for patent owner

    “arguments and evidence, we determine that Patent Owner fails to sufficiently show a nexus between any of its objective indicia evidence and the claimed invention. See Fox Factory, Inc. v. SRAM, LLC, 944 F.3d 1366, 1373 (Fed. Cir. 2019) (“The patentee bears the burden of showing that a nexus exists”). A showing of sufficient nexus is required to establish that the evidence relied upon traces its basis to a novel element in the claim, not to something in the prior art. Institut Pasteur & Universite Pierre Et Marie Curie v. Focarino, 738 F.3d 1337, 1347 (Fed. Cir. 2013). Objective evidence that results from something that is not “both claimed and novel in the claim” lacks a nexus to the merits of the invention. In re Kao, 639 F.3d 1057, 1068 (Fed. Cir. 2011) (emphasis omitted). Thus, establishing nexus involves a showing that novel elements in the claim, not prior-art elements, account for the objective evidence of nonobviousness. Id. As discussed above, Petitioner shows that Capalik teaches all limitations of claim 1. Petitioner persuades us that none of claim 1’s elements individually nor any combination thereof is novel over Capalik’s disclosure. Accordingly, claim 1 is not novel over Capalik, which disproves Patent Owner’s assertion of nexus. PO Resp. 73–76. Moreover, even if claim 1 were novel, Patent Owner otherwise fails to show nexus for its commercial success, praise, or copying assertions. Patent Owner’s evidence does not show that Petitioner’s commercial product embodies claim 1. For example, we agree with Petitioner that Patent Owner “failed to analyze any meaningful detail regarding” how the Falcon Platform allegedly meets limitation 1(d). Reply 28–29. In particular, Patent Owner has not sufficiently addressed limitation 1(d) with the following argument: “1[D] The Falcon Platform transmitted to other computer systems” slip op. at 37

  Patent outcomesUS 9,954,872 mixed
  Claim construction§ 103 obviousnesscites Phillips
  Patents in suitUS 9,954,872
• Samsung Display Co., Ltd. v. Pictiva Displays International Ltd.All claims unpatentable
  PTAB · Jul 22, 2026 · IPR2024-01095 · APJ Garth D Baer · IPR · Remand

  On remand, the Board maintained its finding that claims 2 and 17 are unpatentable under §103 over Diekmann and Ma, and Suzuki and Ma.

  RulingsRemand decision

  • RemandDecided for petitioner

    “that is both n-doped and comprised of 8-hydroxy-quinolinolato-lithium (Liq). The district-court defendant’s first invalidity challenge relied primarily on Clix2, which lacked an n-doped ETL. Paper 48, 2, Paper 50, 3. Thus, the asserted combination required modifying Clix2’s non-doped ETL by adding an n-dopant. Clix2’s missing n-doped ETL appeared to be a focus at trial. See Ex. 2034, 917:1–18, 920:8–14. Here, in contrast, Petitioner proposed a more modest modification to materially different primary references, Suzuki and Diekmann, which both already have n-doped ETLs. See Paper 50, 2–3; Paper 54 8–9. As we explained in our Final Written Decision, because Patent Owner did not contest that Liq acts as an n-dopant in Ma, Petitioner’s combinations were obvious because they merely “substitute one known n-dopant for another to further the same goal of improving ETL conductivity.” Paper 54, 12. That simple-substitution analysis would not be the same when n-doping Clix2’s non-doped ETL. For this reason, we agree with Petitioner that the district-court Clix2-based combination “is a different combination with a materially different motivation-to-combine analysis,” as compared to the Diekmann/Suzuki and Ma combinations that are at issue here. Paper 50, 3.” slip op. at 2

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “Dependent claims 2 and 17 require an electron transport layer (ETL) that is both n-doped and comprised of 8-hydroxy-quinolinolato-lithium (Liq). The district-court defendant’s first invalidity challenge relied primarily on Clix2, which lacked an n-doped ETL. Paper 48, 2, Paper 50, 3. Thus, the asserted combination required modifying Clix2’s non-doped ETL by adding an n-dopant. Clix2’s missing n-doped ETL appeared to be a focus at trial. See Ex. 2034, 917:1–18, 920:8–14. Here, in contrast, Petitioner proposed a more modest modification to materially different primary references, Suzuki and Diekmann, which both already have n-doped ETLs. See Paper 50, 2–3; Paper 54 8–9. As we explained in our Final Written Decision, because Patent Owner did not contest that Liq acts as an n-dopant in Ma, Petitioner’s combinations were obvious because they merely “substitute one known n-dopant for another to further the same goal of improving ETL conductivity.” Paper 54, 12. That simple-substitution analysis would not be the same when n-doping Clix2’s non-doped ETL. For this reason, we agree with Petitioner that the district-court Clix2-based combination “is a different combination with a materially different motivation-to-combine analysis,” as compared to the Diekmann/Suzuki and Ma combinations that are at issue here. Paper 50, 3.” slip op. at 2

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable

    “that is both n-doped and comprised of 8-hydroxy-quinolinolato-lithium (Liq). The district-court defendant’s first invalidity challenge relied primarily on Clix2, which lacked an n-doped ETL. Paper 48, 2, Paper 50, 3. Thus, the asserted combination required modifying Clix2’s non-doped ETL by adding an n-dopant. Clix2’s missing n-doped ETL appeared to be a focus at trial. See Ex. 2034, 917:1–18, 920:8–14. Here, in contrast, Petitioner proposed a more modest modification to materially different primary references, Suzuki and Diekmann, which both already have n-doped ETLs. See Paper 50, 2–3; Paper 54 8–9. As we explained in our Final Written Decision, because Patent Owner did not contest that Liq acts as an n-dopant in Ma, Petitioner’s combinations were obvious because they merely “substitute one known n-dopant for another to further the same goal of improving ETL conductivity.” Paper 54, 12. That simple-substitution analysis would not be the same when n-doping Clix2’s non-doped ETL. For this reason, we agree with Petitioner that the district-court Clix2-based combination “is a different combination with a materially different motivation-to-combine analysis,” as compared to the Diekmann/Suzuki and Ma combinations that are at issue here. Paper 50, 3.” slip op. at 2

  Patent outcomesUS 11,828,425 unpatentable
  § 103 obviousness
  Patents in suitUS 11,828,425
• Posco Co., Ltd. v. ArcelormittalAll claims unpatentable
  PTAB · Jul 16, 2026 · IPR2025-00371 · APJ Brian D Range · IPR · Final written decision

  Claims 1–25 are unpatentable as obvious under § 103 over the asserted combinations of Takagi, Cornette, Suehiro, GMW14400, Laurent, and Vaissiere.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art (POSITA) “would have had an undergraduate degree in materials science, manufacturing engineering, mechanical engineering, or equivalent knowledge, training, or experience, with two years of experience working in metallurgy.” Pet. 6 (citing Ex. 1003 ¶ 15). Patent Owner does not challenge Petitioner’s definition of a POSITA for this proceeding. PO Resp. 8. Because the parties agree and because Petitioner’s proposal is reasonable and consistent with the ’227 patent specification and the prior art, we adopt Petitioner’s proposal. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art).” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for patent owner

    “1. superficial layer The only independent claim at issue, claim 1, recites a “Superficial layer.” Ex. 1001, 15:6. Patent Owner argues that, based on plain and ordinary meaning, the term “superficial layer” refers to a “surface layer” or “top layer.” PO Resp. 8–9. Petitioner does not dispute this construction. See Pet. Reply 21–22 (arguing that the relevant layer of the Suehiro reference is a superficial layer because it is outermost and present at the surface). Because the parties are in agreement and because that agreement is consistent with plain language, claim language, and the ’227 specification, we construe “superficial layer” as referring to a surface layer or top layer.” slip op. at 10

  • Claim Construction › Extrinsic evidence (dictionaries, experts)Term construed petitioner constructionDecided for petitioner

    “defined stoichiometry” (Ex. 2037, 527) but the word may also be a “generic term for phases . . . which may have a narrow or extended compositional stability range” (id.). The first glossary meaning is consistent with Patent Owner’s position. The second, broader, glossary meaning is consistent with Petitioner’s position. Some of the extrinsic sources before us support the broad definition, and some support the narrow definition. See PO Sur-Reply 3–4 (arguing that Dr. Miles admitted that various treatises distinguish intermetallic compounds from alloys and solid solutions). Thus, neither Dr. Miles or Dr. Raabe is “wrong scientifically” in how they use the term “intermetallic” in this proceeding. Id. at 2 (noting that Dr. Miles agreed that Dr. Raabe’s construction is not wrong scientifically). As explained below, however, only one of these meanings is appropriate here. To decide which possible meaning applies to the ’227 patent, we focus on the patent claims and specification. Claim 1 indicates that the intermetallic layer has a “mean composition” (emphasis added). Ex. 1001, 15:1–10. This indicates, albeit weakly, that iron composition across the layer may vary rather than having ordered stoichiometry—consistent with Petitioner’s position. The specification also indicates that “intermetallic alloying” is a possibility—again, consistent with Petitioner’s position. Ex. 1001, 2:47–50. Meanwhile, nothing in the ’227 specification explicitly (or implicitly) suggests that “intermetallic layer” must be limited to elements atomically joined with defined stoichiometry in an ordered crystal structure. We also find that Dr. Miles’s testimony regarding the meaning of “intermetallic” is more credible than Dr. Rabbe’s testimony. Dr. Rabbe, in deposition, stated that Figure 2 of the challenged patent “does not show a layer that meets [his] construction of intermetallic.” Ex. 1078, 129:21–24. The ’227 patent, however, states that Figure 2 includes an “Al-rich Intermetallic layer.” Ex. 1001, Fig. 2, 3:60–64 (“FIG 2. Illustrates a coating … which does not correspond to the invention. This succession of layers (interdiffusion layer and intermetallic layer) yields inferior results in resistance spot welding.”). Also, Dr. Raabe previously referred to a layer of Takagi as having “intermetallic phase layering and structure.” Pet. Reply 4 (citing Ex. 1076 ¶ 166; Ex ¶ 1075, 17) (emphasis omitted). Thus, Dr. Raabe’s construction of “intermetallic” for this proceeding does not fully account for the ’227 patent usage of the word “intermetallic” and does not fully account for Dr. Raabe’s prior usage of the word “intermetallic.” Patent Owner argues that Petitioner’s construction “erases the meaningful distinction” between the claimed layers. PO Resp. 11. Patent Owner further argues that Petitioner’s construction renders the word “intermetallic” superfluous because allowing the intermetallic layer to be “merely a multi-element alloy erases the meaningful distinction among these layers.” Id. We disagree. The word intermetallic serves to require that the layer be composed of two or more metals or a metal and a metalloid. The word intermetallic also serves as a label to differentiate each of the four claimed layers. For example, in claim 1, the word “intermetallic” is used much like the words “interdiffusion” and “intermediate” to give each of the four layers (each having differently mean compositions) different labels.” slip op. at 16

  • Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication establishedDecided for petitioner

    “Because IHS was a company that created an online database with the purpose of providing (selling) standards including General Motors standards to the public, we determine that a person of ordinary skill in the art would have known to look to this database and would have been able to find GMW14400. Patent Owner presents no evidence to the contrary. Because a preponderance of the evidence supports Petitioner, we determine Petitioner establishes GMW14400 is qualifies as prior art.” slip op. at 21

  Patent outcomesUS 11,326,227 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,326,227
• Posco Co., Ltd. v. ArcelormittalAll claims unpatentable
  PTAB · Jul 16, 2026 · IPR2025-00370 · APJ Brian D Range · IPR · Final written decision

  Claims 1–30 are unpatentable as obvious under § 103 over the asserted combinations of prior art.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art (POSITA) “would have had an undergraduate degree in materials science, manufacturing engineering, mechanical engineering, or equivalent knowledge, training, or experience, with two years of experience working in metallurgy.” Pet. 6 (citing Ex. 1003 ¶¶ 13–16). Patent Owner does not challenge Petitioner’s definition of a POSITA for this proceeding. PO Resp. 8. Because the parties agree and because Petitioner’s proposal is reasonable and consistent with the ’602 patent specification and the prior art, we adopt Petitioner’s proposal. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art).” slip op. at 8

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

    “1. superficial layer All independent claims at issue, claims 1, 21, and 24, recite a “superficial layer.” Ex. 1001, 15:11, 16:60, 17:21. Patent Owner argues that, based on plain and ordinary meaning, the term “superficial layer” refers to a “surface layer” or “top layer.” PO Resp. 8–9. Petitioner does not dispute this construction. See Pet. Reply 21–22 (arguing that the relevant layer of the Suehiro reference is a superficial layer because it is outermost and present at the surface). Because the parties are in agreement and because that agreement is consistent with plain language, claim language, and the ’602 specification, we construe “superficial layer” as referring to a surface layer or top layer.” slip op. at 10

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “defined stoichiometry” (Ex. 2037, 527) but the word may also be a “generic term for phases . . . which may have a narrow or extended compositional stability range” (id.). The first glossary meaning is consistent with Patent Owner’s position. The second, broader, glossary meaning is consistent with Petitioner’s position. Some of the sources before us support the broad definition, and some support the narrow definition. See PO Sur-Reply 3–4 (arguing that Dr. Miles admitted that various treatises distinguish intermetallic compounds from alloys and solid solutions) Thus, neither Dr. Miles or Dr. Raabe is “wrong scientifically” in how they use the term “intermetallic” in this proceeding. Id. at 2 (noting that Dr. Miles agreed that Dr. Raabe’s construction is not wrong scientifically). As explained below, however, only one of these meanings is appropriate here. To decide which possible meaning applies to the ’602 patent, we focus on the patent claims and specification. The claims indicate that the intermetallic layer has a “mean iron composition” (emphasis added). Ex. 1001, 15:6–10. This indicates, albeit weakly, that the iron composition across the layer may vary rather than having ordered stoichiometry— consistent with Petitioner’s position. The specification also indicates that “intermetallic alloying” is a possibility—again, consistent with Petitioner’s position. Id. at 2:50–54. Meanwhile, nothing in the ’602 specification explicitly (or implicitly) suggests that “intermetallic layer” must be limited to elements atomically joined with defined stoichiometry in an ordered crystal structure. We also find that Dr. Miles’s testimony regarding the meaning of “intermetallic” is more credible than Dr. Raabe’s testimony. Dr. Raabe, in deposition, stated that Figure 2 of the challenged patent “does not show a layer that meets [his] construction of intermetallic.” Ex. 1078, 129:21–24. The ’602 patent, however, states that Figure 2 includes an “Al-rich Intermetallic layer.” Ex. 1001, Fig. 2, 3:57–61 (“FIG 2. Illustrates a coating . . . which does not correspond to the invention. This succession of layers (interdiffusion layer and intermetallic layer) yields inferior results in resistance spot welding.”). Also, Dr. Raabe previously referred to a layer of Takagi as having “intermetallic phase layering and structure.” Pet. Reply 4 (citing Ex. 1076, 166; Ex. 1075, 17) (emphasis omitted). Thus, Dr. Raabe’s definition of “intermetallic” does not fully account for the ’602 patent usage of the word “intermetallic” and does not fully account for Dr. Raabe’s prior usage of the word “intermetallic.” Patent Owner argues that Petitioner’s construction “erases the meaningful distinction” between the claimed layers. PO Resp. 11. Patent Owner further argues that Petitioner’s construction renders the word “intermetallic” superfluous because allowing the intermetallic layer to be “merely a multi-element alloy erases the meaningful distinction among these layers.” Id. We disagree. The word intermetallic serves to require that the layer be composed of two or more metals or a metal and a metalloid. The word intermetallic also serves as a label to differentiate each of the four claimed layers. For example, in claim 1, the word “intermetallic” is used much like the words “interdiffusion” and “intermediate” to give each of the four layers (each having differently defined mean iron compositions) different labels.” slip op. at 16

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner

    “have had reason to combine teachings of Takagi and Cornette with a reasonable expectation of success. Pet. 11–20 (citing, e.g., Ex. 1003 ¶¶ 28– 42; Ex. 1016 ¶ 35; Ex. 1014, 9; Ex. 1025, 5:17–20; Ex. 1026, 7; Ex. 1034 ¶ 13). In particular, Petitioner argues that Takagi discloses a pre-coating thickness of 10–20 µm but does not explicitly disclose a post hot-stamping coating thickness corresponding to the pre-coating thickness. Pet. 11. Cornette teaches that the hot-stamping thickness causes coating expansion from 25 µm to about 40 µm, an increase of 60%. Id. (citations omitted). Petitioner and Dr. Miles reason that, when hot stamping Takagi’s product, the thickness would be 32 µm. Id. (citing Ex. 1003 ¶ 32); see also Pet. Reply 20–21. Thus, Patent Owner argues that Cornette evidences Takagi’s finally coating thickness without requiring modification of Takagi. Petitioner further argues that Takagi and Cornette teach that post hot- stamping thickness could be varied and optimized as a result effective variable. Id. at 12–13; see also Pet. Reply 17–18. Cornette teaches, for example, that “[t]he average [pre-coating] layer thickness showing the best compromise between corrosion protection and weldability is 25 µm” and links this pre-coating thickness to a final thickness of “about 40 µm at the steel surface.” Ex. 1014, 9. Petitioner also argues that it would have been obvious to fill in other details of Takagi including, for example, selecting USIBOR 1500 steel, based on the teachings of Cornette. Pet. 14. Patent Owner argues that there is no reason to combine Takagi with the teachings of Cornette. PO Resp. 26. Patent Owner makes seven related arguments. Patent Owner first argues that the Petitioner’s position is speculative and lacks basis. Id. at 26–27. We disagree. Cornette evidences a final coating thickness for Takagi, and the references also suggest that final coating thickness is result effective. Second, Patent Owner argues that there would have been no incentive to seek a motivation to seek a thicker coating post-hot stamping. Id. at 28– 35. This argument does not undermine Petitioner’s position that Takagi, by itself, would have reached a thicker coating after stamping as evidenced by Cornette. Pet. 11–12. Petitioner takes the position, with evidence, that practice of Takagi alone would reach the recited thickness. No motivation to modify Takagi is required under this position.” slip op. at 25

  Patent outcomesUS 10,961,602 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 10,961,602
• Innoscience America, Inc. v. Infineon Technologies Americas Corp.No claims unpatentable
  PTAB · Jun 30, 2026 · IPR2025-00175 · APJ Jo-Anne M Kokoski · IPR · Final written decision

  Claims 1–17 were not shown unpatentable because Petitioner failed to establish that Usui’s interconnect structure or Yu’s metal gate stacks satisfy the construed “electrode stack” limitation.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “(“POSITA” or “POSA”) would have had “at least a four-year degree in electrical engineering or a closely related field, and at least two years of experience in semiconductor device design,” and “[a]dditional education could substitute for professional experience and vice versa.” Pet. 6 (citing Ex. 1002 ¶¶ 80–82). Patent Owner does not dispute Petitioner’s proposed level of ordinary skill. PO Resp. 1–76. Neither party explains why the outcome of this case would be affected by the adoption of the proffered definition of a person of ordinary skill in the art. In the Institution Decision, we adopted the assessment offered by Petitioner. Dec. 6–7. Because Petitioner’s definition of the level of skill in the art is consistent with the ’562 patent and the asserted prior art, we maintain Petitioner’s definition for purposes of this Final Written Decision. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir 2001).” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “comprises the recited metals and has the recited thickness, which forms an electrical contact for use on a semiconductor device generally or a group III- V semiconductor in particular. This is consistent with our determination that “electrode stack” is a conductor that provides a path for current entering or leaving a medium such as a semiconductor device We disagree with Patent Owner that “electrode stack” as used in the challenged claims should be limited to the specific electrodes shown in the embodiments described in the Specification. See PO Resp. 4–9. Although the Specification describes embodiments using source, drain, and Schottky gate electrodes as electrical contacts, we see no reason to construe the term “electrode stack” itself to be limited to these components as Patent Owner proposes. Claims 1 and 13 expressly recite that electrode stacks comprise the claimed “electrical contact,” without expressly including or precluding any specific type of electrode. Ex. 1001, 5:54–63, 6:37–47. The Federal Circuit advises that the Specification “is not a substitute for, nor can it be used to rewrite, the chosen claim language. ‘Specifications teach. Claims claim.’” SuperGuide, 358 F.3d at 875 (quoting SRI Int’l v. Matsushita Elec. Corp. of Am., 775 F.2d 1107, 1121 n.14 (Fed. Cir. 1985) (en banc)). The Specification does teach electrical contacts that include source, drain, and Schottky gate electrodes, but claims 1 and 13 are directed to electrical contacts that are not expressly so limited. Patent Owner’s proposed construction would effectively rewrite the claim by adding limitations, which we decline to do under the guise of claim construction. See id. (“Though understanding the claim language may be aided by the explanations contained in the written description, it is important not to import into a claim limitations that are not a part of the claim.”). In view of the foregoing, we construe the claim term “electrode stack” to mean “a conductor that provides a path for current entering or leaving a medium such as a semiconductor device.”” slip op. at 17

  • Expert testimonyPetitioner expert discountedDecided for patent owner

    “that the identified layers in Usui’s interconnect metallurgy structure form an “electrode stack including a plurality of metal layers and a capping layer formed over said plurality of metal layers” as recited in claim 1. See Pet. 11–12 (citing Ex. 1002 ¶¶ 89–91). Neither Petitioner nor Dr. Zhao, however, provide adequate explanation or evidence as to why Usui’s interconnect metallurgy structure forms an “electrode stack,” i.e., a conductor that provides a path for current entering or leaving a medium such as a semiconductor device. Dr. Zhao’s testimony merely repeats the disclosures in Usui and concludes, without further technical detail, explanation, or reference to objective evidence, that Usui’s Figure 8 discloses an electrode stack. Ex. 1002 ¶¶ 89–91. Dr. Zhao’s testimony sets forth Petitioner’s conclusory assertions as though they are facts, rather than setting forth facts and evidence in support of those assertions. Compare id. with Pet. 11–12. Absent underlying facts or evidence to support Dr. Zhao’s opinion, the cited testimony “adds little to the conclusory assertion for which it is offered to support, and is entitled to little weight.” Xerox Corp. v. Bytemark, Inc., IPR2022-00624, Paper 9 at 15 (PTAB Aug. 24, 2022) (precedential). In contrast, Patent Owner’s declarant Dr. Piner testifies, with evidentiary support, that interconnects (such as Usui’s interconnect metallurgy structure) and electrical contacts (such as that claimed in the ’562 patent) are not the same thing. See Ex. 2024 ¶¶ 63–70. For example, Dr. Piner explains: In other words, not all metals in a semiconductor device have the same purpose and could not be said to be interchangeable. By August 2009 it was well known to a POSA how to discern if a metal component in a transistor is an interconnect or serves as an electrical contact such as a gate contact or ohmic contact, based on the structure and functionality of the metal component. For example, interconnects are made up of metal strips and are deposited on insulators. EX-1011 (Mishra) at 216. Interconnects are low resistance conductors that can carry very high current densities. Id., 216, 217. Unlike Schottky contacts and ohmic contacts, interconnects do not provide non-linear IV response like Schottky contacts nor inject electrons and holes into semiconductors like ohmic contacts. Id., 218. As many of the references cited by Dr. Zhao illustrate, electrical contacts had their own highly complex design challenges. EX-1008 (Pearton), 41-59 (Pages 53-71 of 383) (discussing electrical contacts); EX-1017 (Kramer), 11-126 (Pages 18-130 of 151) (same). And while Dr. Zhao cites these as supporting a POSA’s knowledge of an electrical contact, none of these references describe electrical contacts as interconnects. Id. ¶ 71. Dr. Piner further testifies that Usui’s interconnect metallurgy structure is an interconnect, and not an electrical contact, because “Usui states that ‘[t]he structures fabricated by the process of the present invention are especially useful for forming electrical connections or wiring such as between active and/or passive devices of an integrated circuit structure.’” Id. ¶ 148 (citing Ex. 1004, 1:11–14) (alteration in original); see also id. ¶¶ 150– 151 (Dr. Piner testifying that Usui’s interconnect metallization structure is not an “electrode stack” under a broad definition of electrode). Dr. Piner’s testimony in this regard rebuts Petitioner’s and Dr. Zhao’s conclusory assertions to the contrary.” slip op. at 21

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

    “conductor that provides a path for current entering or leaving a medium such as a semiconductor device.” Thus, Petitioner must show that Usui’s layers 13–15, 18, and 19 provide a path for current entering or leaving a medium such as a semiconductor device. After reviewing the complete trial record, we are not persuaded that Petitioner has done so. Petitioner relies on the testimony of Dr. Zhao to support its contention that the identified layers in Usui’s interconnect metallurgy structure form an “electrode stack including a plurality of metal layers and a capping layer formed over said plurality of metal layers” as recited in claim 1. See Pet. 11–12 (citing Ex. 1002 ¶¶ 89–91). Neither Petitioner nor Dr. Zhao, however, provide adequate explanation or evidence as to why Usui’s interconnect metallurgy structure forms an “electrode stack,” i.e., a conductor that provides a path for current entering or leaving a medium such as a semiconductor device. Dr. Zhao’s testimony merely repeats the disclosures in Usui and concludes, without further technical detail, explanation, or reference to objective evidence, that Usui’s Figure 8 discloses an electrode stack. Ex. 1002 ¶¶ 89–91. Dr. Zhao’s testimony sets forth Petitioner’s conclusory assertions as though they are facts, rather than setting forth facts and evidence in support of those assertions. Compare id. with Pet. 11–12. Absent underlying facts or evidence to support Dr. Zhao’s opinion, the cited testimony “adds little to the conclusory assertion for which it is offered to support, and is entitled to little weight.” Xerox Corp. v. Bytemark, Inc., IPR2022-00624, Paper 9 at 15 (PTAB Aug. 24, 2022) (precedential).” slip op. at 21

  Patent outcomesUS 8,686,562 not shown unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 8,686,562
• Luxottica Of America, Inc. v. E-Vision Smart Optics, Inc.Adverse judgment
  PTAB · Jun 29, 2026 · IPR2025-01512 · APJ Arthur M Peslak · IPR · Adverse judgment

  The Board granted Patent Owner’s request for adverse judgment, cancelled claims 1–27, and terminated the proceeding.

  RulingsAdverse judgment

  • Adverse judgmentAdverse judgmentGranted

    “A party may request entry of adverse judgment against itself at any time during an inter partes review proceeding. See 37 C.F.R. § 42.73(b). Under these circumstances, entry of judgment adverse to the Patent Owner is appropriate as to claims 1–27 of the ’612 patent. Consequently, we grant Patent Owner's request for adverse judgment.” slip op. at 2

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
  None
  Patents in suitUS 11,971,612

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.