- Uatp IP LLC v. Slick Slide LLCSome claims unpatentablePTAB · Oct 2, 2026 · PGR2024-00054 · APJ Brian D Range · PGR · Final written decision
Claims 22–26 are unpatentable based on obviousness; claims 1–17, 27, and 28 were not shown unpatentable. Patent Owner’s motion to terminate was denied.
RulingsFinal written decision- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed board ownDecided for patent owner
“1. Mesh Layer Petitioner contends “no formal claim construction is necessary in this” slip op. at 13
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable
“5. Analysis On this complete record, we determine that Petitioner’s arguments do” slip op. at 31
- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable
“form of nylon and some form of Teflon (and possible combinations thereof) having the specific coefficient of friction range given in limitation [1c] breaks down, because the building blocks of the obviousness argument are not sufficiently identified in Phillips alone, nor in the supporting testimony. Accordingly, we determine that Petitioner’s arguments and evidence fail to show that Phillips renders the challenged claims obvious. 6. Conclusion Based on the foregoing, we determine that Petitioner has not established by a preponderance of the evidence that claims 1–4, 6, and 7 would have been anticipated by or obvious in view of Phillips.” slip op. at 33
- Obviousness (§103) › Objective indicia / secondary considerations › NexusObjective indicia no nexusDecided for petitioner
“2. Products and Nexus We first consider the issue of whether certain evidence relied upon by” slip op. at 20
Patent outcomesUS 11,998,854 mixedClaim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · Graham · NautilusPatents in suitUS 11,998,854 - Shenzhen Tuozhu Technology Co., Ltd. v. Stratasys, Inc.All claims unpatentablePTAB · Sep 28, 2026 · IPR2025-00611 · APJ Christopher L Ogden · IPR · Final written decision
Claims 1–10, 12, 13, 19, and 20 are unpatentable under § 103 over the stated Douglas–Mark and Hamilton-based grounds.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“The parties agree that experience could substitute for a degree, and vice versa. Pet. 3; PO Resp. 10. The parties’ proposed levels of ordinary skill are substantially similar. For this decision, as in the Institution Decision, we adopt Petitioner’s proposed level, which is supported by credible testimonial evidence and is consistent with the problems addressed in the ’774 patent. See Ex. 1001, 1:16–52. Our decision would be the same, however, if we were to adopt Patent Owner’s proposal.” slip op. at 7
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Other
“Neither Petitioner nor Patent Owner argues that we need to construe any claim terms explicitly. See Pet. 2–3; PO Resp. 10. However, the parties contest two material claim-construction issues which we address below. To the extent that the parties’ positions depend on interpreting other claim language in a particular way, we discuss the relevant claim language below in the context of the parties’ arguments regarding the prior art.” slip op. at 8
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner
“We disagree with Patent Owner that a person of ordinary skill in the art would have understood that limitation 1.2 must be performed before limitations 1.3 or 1.4. See Ex. 1001, 35:21–24. See Interactive Gift Exp., Inc. v. Compuserve Inc., 256 F.3d 1323, 1342 (Fed. Cir. 2001) (“Unless the steps of a method actually recite an order, the steps are not ordinarily construed to require one.” (citing Loral Fairchild Corp. v. Sony Corp., 181 F.3d 1313, 1322 (Fed. Cir. 1999)). The evidence suggests that a “target printer” is any printer that is ultimately selected for fabricating the object, and such a printer could send its configuration information either before or after that determination is made in limitation 1.2. This interpretation does not render the word “target” meaningless. At some point, a printer must be determined to be the target printer, which is the one intended to ultimately fabricate the three-dimensional object. But the target printer still exists, and is capable of being queried, before that determination is made. We find the examples in the ’774 patent pertinent to this question. The ’774 patent states that “the target printer may include more than one printer.” Ex. 1001, 18:66–67. In discussing the step of “query target printer for properties 306” (Fig. 3A), the ’774 patent states that “[i]n one aspect, numerous queries are sent to numerous printers, e.g., for use in selecting one or more of the printers as the target printer.” Id. at 19:8–10. Alternatively, “the query is sent to a printer that is not necessarily the target printer as described herein, e.g., when the query or information received from a response to the query is used for the selection of the target printer.” Id. at 19:11–14. Importantly, the second embodiment states that the queried printer “is not necessarily the target printer,” suggesting that the queried printer could be the target printer even before it is determined to be such. Id. at 19:11–12 (emphasis added). Based on the evidence of record, a person of ordinary skill in the art would have understood that the “target printer” can be determined after the query recited in limitation 1.3 or the reception of configuration information recited in limitation 1.4. Thus, the evidence does not impose an ordering between limitations 1.2 and 1.3 or between limitations 1.2 and 1.4. The evidence also does not support Patent Owner’s argument that the two reverse-order examples in the ’774 patent are unclaimed embodiments.” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightMotivation foundDecided for petitioner
“We disagree that Petitioner’s arguments are based on impermissible hindsight, because they are based on the disclosures in Douglas and Mark, and Petitioner has articulated a persuasive reason to combine those references without referring to the ’774 patent itself, as we discuss below. See In re McLaughlin, 443 F.2d 1392, 1395 (CCPA 1971) (an obvious rationale is not improper hindsight if it “takes into account only knowledge which was within the level of ordinary skill at the time the claimed invention was made and does not include knowledge gleaned only from applicant’s disclosure”).” slip op. at 29
Patent outcomesUS 11,886,774 unpatentableClaim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,886,774 - Posco Co., Ltd. v. ArcelormittalAll claims unpatentablePTAB · Jul 16, 2026 · IPR2025-00371 · APJ Brian D Range · IPR · Final written decision
Claims 1–25 are unpatentable as obvious under § 103 over the asserted combinations of Takagi, Cornette, Suehiro, GMW14400, Laurent, and Vaissiere.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person of ordinary skill in the art (POSITA) “would have had an undergraduate degree in materials science, manufacturing engineering, mechanical engineering, or equivalent knowledge, training, or experience, with two years of experience working in metallurgy.” Pet. 6 (citing Ex. 1003 ¶ 15). Patent Owner does not challenge Petitioner’s definition of a POSITA for this proceeding. PO Resp. 8. Because the parties agree and because Petitioner’s proposal is reasonable and consistent with the ’227 patent specification and the prior art, we adopt Petitioner’s proposal. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art).” slip op. at 8
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for patent owner
“1. superficial layer The only independent claim at issue, claim 1, recites a “Superficial layer.” Ex. 1001, 15:6. Patent Owner argues that, based on plain and ordinary meaning, the term “superficial layer” refers to a “surface layer” or “top layer.” PO Resp. 8–9. Petitioner does not dispute this construction. See Pet. Reply 21–22 (arguing that the relevant layer of the Suehiro reference is a superficial layer because it is outermost and present at the surface). Because the parties are in agreement and because that agreement is consistent with plain language, claim language, and the ’227 specification, we construe “superficial layer” as referring to a surface layer or top layer.” slip op. at 10
- Claim Construction › Extrinsic evidence (dictionaries, experts)Term construed petitioner constructionDecided for petitioner
“defined stoichiometry” (Ex. 2037, 527) but the word may also be a “generic term for phases . . . which may have a narrow or extended compositional stability range” (id.). The first glossary meaning is consistent with Patent Owner’s position. The second, broader, glossary meaning is consistent with Petitioner’s position. Some of the extrinsic sources before us support the broad definition, and some support the narrow definition. See PO Sur-Reply 3–4 (arguing that Dr. Miles admitted that various treatises distinguish intermetallic compounds from alloys and solid solutions). Thus, neither Dr. Miles or Dr. Raabe is “wrong scientifically” in how they use the term “intermetallic” in this proceeding. Id. at 2 (noting that Dr. Miles agreed that Dr. Raabe’s construction is not wrong scientifically). As explained below, however, only one of these meanings is appropriate here. To decide which possible meaning applies to the ’227 patent, we focus on the patent claims and specification. Claim 1 indicates that the intermetallic layer has a “mean composition” (emphasis added). Ex. 1001, 15:1–10. This indicates, albeit weakly, that iron composition across the layer may vary rather than having ordered stoichiometry—consistent with Petitioner’s position. The specification also indicates that “intermetallic alloying” is a possibility—again, consistent with Petitioner’s position. Ex. 1001, 2:47–50. Meanwhile, nothing in the ’227 specification explicitly (or implicitly) suggests that “intermetallic layer” must be limited to elements atomically joined with defined stoichiometry in an ordered crystal structure. We also find that Dr. Miles’s testimony regarding the meaning of “intermetallic” is more credible than Dr. Rabbe’s testimony. Dr. Rabbe, in deposition, stated that Figure 2 of the challenged patent “does not show a layer that meets [his] construction of intermetallic.” Ex. 1078, 129:21–24. The ’227 patent, however, states that Figure 2 includes an “Al-rich Intermetallic layer.” Ex. 1001, Fig. 2, 3:60–64 (“FIG 2. Illustrates a coating … which does not correspond to the invention. This succession of layers (interdiffusion layer and intermetallic layer) yields inferior results in resistance spot welding.”). Also, Dr. Raabe previously referred to a layer of Takagi as having “intermetallic phase layering and structure.” Pet. Reply 4 (citing Ex. 1076 ¶ 166; Ex ¶ 1075, 17) (emphasis omitted). Thus, Dr. Raabe’s construction of “intermetallic” for this proceeding does not fully account for the ’227 patent usage of the word “intermetallic” and does not fully account for Dr. Raabe’s prior usage of the word “intermetallic.” Patent Owner argues that Petitioner’s construction “erases the meaningful distinction” between the claimed layers. PO Resp. 11. Patent Owner further argues that Petitioner’s construction renders the word “intermetallic” superfluous because allowing the intermetallic layer to be “merely a multi-element alloy erases the meaningful distinction among these layers.” Id. We disagree. The word intermetallic serves to require that the layer be composed of two or more metals or a metal and a metalloid. The word intermetallic also serves as a label to differentiate each of the four claimed layers. For example, in claim 1, the word “intermetallic” is used much like the words “interdiffusion” and “intermediate” to give each of the four layers (each having differently mean compositions) different labels.” slip op. at 16
- Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication establishedDecided for petitioner
“Because IHS was a company that created an online database with the purpose of providing (selling) standards including General Motors standards to the public, we determine that a person of ordinary skill in the art would have known to look to this database and would have been able to find GMW14400. Patent Owner presents no evidence to the contrary. Because a preponderance of the evidence supports Petitioner, we determine Petitioner establishes GMW14400 is qualifies as prior art.” slip op. at 21
Patent outcomesUS 11,326,227 unpatentableClaim construction§ 102 anticipation§ 103 obviousnesscites KSR · GrahamPatents in suitUS 11,326,227 - Posco Co., Ltd. v. ArcelormittalAll claims unpatentablePTAB · Jul 16, 2026 · IPR2025-00370 · APJ Brian D Range · IPR · Final written decision
Claims 1–30 are unpatentable as obvious under § 103 over the asserted combinations of prior art.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person of ordinary skill in the art (POSITA) “would have had an undergraduate degree in materials science, manufacturing engineering, mechanical engineering, or equivalent knowledge, training, or experience, with two years of experience working in metallurgy.” Pet. 6 (citing Ex. 1003 ¶¶ 13–16). Patent Owner does not challenge Petitioner’s definition of a POSITA for this proceeding. PO Resp. 8. Because the parties agree and because Petitioner’s proposal is reasonable and consistent with the ’602 patent specification and the prior art, we adopt Petitioner’s proposal. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art).” slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner
“1. superficial layer All independent claims at issue, claims 1, 21, and 24, recite a “superficial layer.” Ex. 1001, 15:11, 16:60, 17:21. Patent Owner argues that, based on plain and ordinary meaning, the term “superficial layer” refers to a “surface layer” or “top layer.” PO Resp. 8–9. Petitioner does not dispute this construction. See Pet. Reply 21–22 (arguing that the relevant layer of the Suehiro reference is a superficial layer because it is outermost and present at the surface). Because the parties are in agreement and because that agreement is consistent with plain language, claim language, and the ’602 specification, we construe “superficial layer” as referring to a surface layer or top layer.” slip op. at 10
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner
“defined stoichiometry” (Ex. 2037, 527) but the word may also be a “generic term for phases . . . which may have a narrow or extended compositional stability range” (id.). The first glossary meaning is consistent with Patent Owner’s position. The second, broader, glossary meaning is consistent with Petitioner’s position. Some of the sources before us support the broad definition, and some support the narrow definition. See PO Sur-Reply 3–4 (arguing that Dr. Miles admitted that various treatises distinguish intermetallic compounds from alloys and solid solutions) Thus, neither Dr. Miles or Dr. Raabe is “wrong scientifically” in how they use the term “intermetallic” in this proceeding. Id. at 2 (noting that Dr. Miles agreed that Dr. Raabe’s construction is not wrong scientifically). As explained below, however, only one of these meanings is appropriate here. To decide which possible meaning applies to the ’602 patent, we focus on the patent claims and specification. The claims indicate that the intermetallic layer has a “mean iron composition” (emphasis added). Ex. 1001, 15:6–10. This indicates, albeit weakly, that the iron composition across the layer may vary rather than having ordered stoichiometry— consistent with Petitioner’s position. The specification also indicates that “intermetallic alloying” is a possibility—again, consistent with Petitioner’s position. Id. at 2:50–54. Meanwhile, nothing in the ’602 specification explicitly (or implicitly) suggests that “intermetallic layer” must be limited to elements atomically joined with defined stoichiometry in an ordered crystal structure. We also find that Dr. Miles’s testimony regarding the meaning of “intermetallic” is more credible than Dr. Raabe’s testimony. Dr. Raabe, in deposition, stated that Figure 2 of the challenged patent “does not show a layer that meets [his] construction of intermetallic.” Ex. 1078, 129:21–24. The ’602 patent, however, states that Figure 2 includes an “Al-rich Intermetallic layer.” Ex. 1001, Fig. 2, 3:57–61 (“FIG 2. Illustrates a coating . . . which does not correspond to the invention. This succession of layers (interdiffusion layer and intermetallic layer) yields inferior results in resistance spot welding.”). Also, Dr. Raabe previously referred to a layer of Takagi as having “intermetallic phase layering and structure.” Pet. Reply 4 (citing Ex. 1076, 166; Ex. 1075, 17) (emphasis omitted). Thus, Dr. Raabe’s definition of “intermetallic” does not fully account for the ’602 patent usage of the word “intermetallic” and does not fully account for Dr. Raabe’s prior usage of the word “intermetallic.” Patent Owner argues that Petitioner’s construction “erases the meaningful distinction” between the claimed layers. PO Resp. 11. Patent Owner further argues that Petitioner’s construction renders the word “intermetallic” superfluous because allowing the intermetallic layer to be “merely a multi-element alloy erases the meaningful distinction among these layers.” Id. We disagree. The word intermetallic serves to require that the layer be composed of two or more metals or a metal and a metalloid. The word intermetallic also serves as a label to differentiate each of the four claimed layers. For example, in claim 1, the word “intermetallic” is used much like the words “interdiffusion” and “intermediate” to give each of the four layers (each having differently defined mean iron compositions) different labels.” slip op. at 16
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner
“have had reason to combine teachings of Takagi and Cornette with a reasonable expectation of success. Pet. 11–20 (citing, e.g., Ex. 1003 ¶¶ 28– 42; Ex. 1016 ¶ 35; Ex. 1014, 9; Ex. 1025, 5:17–20; Ex. 1026, 7; Ex. 1034 ¶ 13). In particular, Petitioner argues that Takagi discloses a pre-coating thickness of 10–20 µm but does not explicitly disclose a post hot-stamping coating thickness corresponding to the pre-coating thickness. Pet. 11. Cornette teaches that the hot-stamping thickness causes coating expansion from 25 µm to about 40 µm, an increase of 60%. Id. (citations omitted). Petitioner and Dr. Miles reason that, when hot stamping Takagi’s product, the thickness would be 32 µm. Id. (citing Ex. 1003 ¶ 32); see also Pet. Reply 20–21. Thus, Patent Owner argues that Cornette evidences Takagi’s finally coating thickness without requiring modification of Takagi. Petitioner further argues that Takagi and Cornette teach that post hot- stamping thickness could be varied and optimized as a result effective variable. Id. at 12–13; see also Pet. Reply 17–18. Cornette teaches, for example, that “[t]he average [pre-coating] layer thickness showing the best compromise between corrosion protection and weldability is 25 µm” and links this pre-coating thickness to a final thickness of “about 40 µm at the steel surface.” Ex. 1014, 9. Petitioner also argues that it would have been obvious to fill in other details of Takagi including, for example, selecting USIBOR 1500 steel, based on the teachings of Cornette. Pet. 14. Patent Owner argues that there is no reason to combine Takagi with the teachings of Cornette. PO Resp. 26. Patent Owner makes seven related arguments. Patent Owner first argues that the Petitioner’s position is speculative and lacks basis. Id. at 26–27. We disagree. Cornette evidences a final coating thickness for Takagi, and the references also suggest that final coating thickness is result effective. Second, Patent Owner argues that there would have been no incentive to seek a motivation to seek a thicker coating post-hot stamping. Id. at 28– 35. This argument does not undermine Petitioner’s position that Takagi, by itself, would have reached a thicker coating after stamping as evidenced by Cornette. Pet. 11–12. Petitioner takes the position, with evidence, that practice of Takagi alone would reach the recited thickness. No motivation to modify Takagi is required under this position.” slip op. at 25
Patent outcomesUS 10,961,602 unpatentableClaim construction§ 102 anticipation§ 103 obviousnesscites KSR · GrahamPatents in suitUS 10,961,602 - PTAB · Dec 3, 2025 · IPR2025-01026 · APJ Steven M Amundson · IPR · Institution
The Board instituted review of claims 1–20 on all petition challenges because the Baliarda-543 challenges met the reasonable-likelihood threshold.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“to institute an inter partes review. We may institute an inter partes review only if “the information presented in the petition filed under section 311 and any response filed under section 313 shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a) (2024). The “reasonable likelihood” standard is “a higher standard than mere notice pleading” but “lower than the ‘preponderance’ standard to prevail in a final written decision.” Hulu, LLC v. Sound View Innovations, LLC, IPR2018- 01039, Paper 29 at 13 (PTAB Dec. 20, 2019) (precedential). Based on the current record and for the reasons explained below, Petitioner has shown that there is a reasonable likelihood that it would prevail with respect to at least one of the challenged claims. Thus, we 1 Petitioner filed a confidential version of the Petition as Paper 3 and a public version of the Petition as Paper 4. We cite to the public version of the Petition. institute an inter partes review of claims 1–20 in the ’677 patent on all challenges included in the Petition.” slip op. at 2
- Skill levelSkill level petitioner adoptedOther
“Petitioner asserts that a person of ordinary skill as of the ’677 patent’s effective filing date would have had “at least a bachelor’s degree in electrical engineering, computer science, or a similar degree and at least four years of experience in applied electromagnetics with an emphasis on antennas.” Pet. 11 (quoting Ex. 1018 ¶ 32). Petitioner also asserts that “[a]lternatively, the person of ordinary skill in the art would have a master’s degree in electrical engineering (or similar discipline) and at least two years of similar experience.” Id. (quoting Ex. 1018 ¶ 32). Dr. van der Weide’s testimony supports Petitioner’s assertions. See Ex. 1007 ¶ 40. For purposes of the Preliminary Response only, Patent Owner employs Petitioner’s description of an ordinarily skilled artisan. Prelim. Resp. 17. Based on the current record and for purposes of this decision, we accept Petitioner’s description of an ordinarily skilled artisan because it comports with the technology and claims of the ’677 patent as well as the asserted references. See, e.g., Ex. 1001, 1:26–6:47, 42:47–44:61, code (57); infra §§ III.E.1–III.E.2.” slip op. at 23
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“4. DISCUSSION “[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.” Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999); see Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017). Based on the current record, we determine that no claim term, phrase, or limitation requires an explicit construction to decide whether Petitioner satisfies the “reasonable likelihood” standard for instituting trial.” slip op. at 26
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable
“Although “Dou does not require its ‘diversity antenna architecture’ to provide spatial diversity,” Dou nevertheless requires a wireless device with some type of diversity antenna architecture. See, e.g., Ex. 1013 ¶¶ 14, 17–18, 22–24, 30, 32–34, codes (54), (57), claims 1 and 16. As an example, Dou’s independent claim 1 covering a “wireless device” requires a “first diversity antenna” and a “second diversity antenna.” Id. at claim 1. As another example, Dou’s independent claim 16 covering a “wireless device” also requires a “first diversity antenna” and a “second diversity antenna.” Id. at claim 16. As yet another example, Dou’s Abstract describes a “wireless device” including a “first diversity antenna” and a “second diversity antenna.” Id. at code (57). Petitioner does not explain how the proposed combination provides anything other than spatial diversity. See Pet. 33–35; Prelim. Reply 1–3; Ex. 1007 ¶¶ 118–124. Based on the current record, we agree with Patent Owner that with Ciais-Quadband’s antenna used for Dou’s two antennas 206 and 208, the two identical quadband antennas would have:” slip op. at 46
Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · KSR · GrahamPatents in suitUS 11,031,677 - PTAB · Dec 3, 2025 · IPR2025-01027 · APJ Steven M Amundson · IPR · Institution
The Board instituted IPR of claims 1–20 on all petition challenges, finding a reasonable likelihood that Baliarda-543 anticipates or renders obvious those claims.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“to institute an inter partes review. We may institute an inter partes review only if “the information presented in the petition filed under section 311 and any response filed under section 313 shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a) (2024). The “reasonable likelihood” standard is “a higher standard than mere notice pleading” but “lower than the ‘preponderance’ standard to prevail in a final written decision.” Hulu, LLC v. Sound View Innovations, LLC, IPR2018- 01039, Paper 29 at 13 (PTAB Dec. 20, 2019) (precedential).” slip op. at 2
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable
“Regarding spatial diversity, Dou explains that a first internal antenna and a second internal antenna “may be separated by a distance (D) that is no less than the quarter wavelength (>=λ/4) of the lowest frequency.” Ex. 1013 ¶ 24; see Ex. 2010 ¶¶ 35, 44. Consistent with Dou’s preference for at least a quarter-wavelength spacing between antennas at the lowest frequency, “a commonly accepted rule of thumb is that at least a quarter-wavelength spacing between antennas is necessary to provide effective spatial diversity.” Ex. 2010 ¶¶ 33, 35, 47. Effective spatial diversity requires sufficient spacing between antennas because that technique “uses multiple antennas to improve signal reliability and performance by mitigating the effects of multipath fading and other interference.” Ex. 2010 ¶ 33. “Multipath fading occurs when a wireless signal propagates along multiple different paths of differing lengths because of interactions with obstacles, resulting in portions of the signal energy arriving at a receiver with different phases slightly offset in time.” Id. Locations insufficiently separated in terms of wavelength “tend to experience similar fading and interference characteristics.” Id. Thus, closely spaced antennas “cannot provide effective spatial diversity.” Id. By providing sufficient spacing between antennas, however, “the likelihood increases that at least one of the antennas will be positioned at a location where the multipath or other interference is relatively low, thereby improving overall signal quality and reliability.” Id. As Patent Owner contends, the proposed combination modifies Dou’s ground plane 310 to replicate Jing’s ground plane with dimensions of 36 mm × 60 mm and limits “the extent of Dou’s ground plane 310 so that it [does] not extend behind Jing’s antenna at 306, just like Dou does not extend it behind antenna 308.” See Pet. 35–36; Prelim. Resp. 20 (quoting Pet. 35); Prelim. Sur-reply 1; Ex. 1007 ¶ 120; Ex. 2010 ¶ 45. The lowest frequency of Jing’s antenna is 900 MHz. Ex. 1011, 2657–58; see Ex. 1007 ¶¶ 118, 154; Ex. 2010 ¶¶ 37, 44. The wavelength (λ) corresponding to a frequency of 900 MHz is 333.3 mm, and a quarter wavelength (λ/4) is 83.3 mm. Ex. 2010 ¶ 44. In the proposed combination, a distance of 60 mm separates the” slip op. at 49
- Disclosure Requirements (§112) › Written description (Ariad)Written description inadequateNot entitled to earlier dateDecided for petitioner
“To satisfy the written-description requirement, the inventor must have possession of the claimed invention as interpreted to encompass an allegedly infringing product. See Rivera, 857 F.3d at 1319–22; ICU Med., 558 F.3d at 1372–73, 1377–79. For purposes of the written-description requirement, the “invention” is “whatever is now claimed.” Vas-Cath, 935 F.2d at 1564 (emphasis omitted). Based on the current record, and as Petitioner asserts, LTE band 12 was not available for “use with mobile communications” or “use in any cellular communication, let alone LTE or 4G communication,” as of the ’429 application’s December 21, 2006, filing date. See Ex. 1007 ¶¶ 229, 231; Pet. 76–77. For instance, a Federal Communications Commission report adopted on July 31, 2007, notes that the 698-806 MHz spectrum “currently is occupied by television broadcasters in TV Channels 52-69.” Ex. 1045, 1, 3; see Ex. 1007 ¶ 231. The 698-806 MHz spectrum includes LTE band 12 with 698-716 MHz for uplink and 728-746 MHz for downlink. See Ex. 1026, 11 (Table 1); Ex. 1039, 498 (Table 20.1). At this stage of the proceeding, Patent Owner does not dispute that as of July 31, 2007, the 698-806 MHz spectrum was “occupied by television broadcasters in TV Channels 52-69.” See Prelim. Resp. 2–3, 23–30; Prelim. Sur-reply 5. Thus, based on the current record, Petitioner demonstrates a reasonable likelihood that as of the ’429 application’s December 21, 2006, filing date, the ’429 application did not “reasonably convey[] to those skilled in the art that the inventor had possession” of “an antenna configured to send or receive signals in the 698-806 MHz spectrum,” including LTE band 12 that Patent Owner relies on in the Geotab litigation, for “communication with any ‘4G communication standard’ because those frequencies were not usable for any mobile device communications at the time of filing.” See Pet. 78 (emphasis omitted); Ex. 1007 ¶¶ 231, 233–234, 236–237; Ex. 1045, 1, 3; Ariad, 598 F.3d at 1351. Accordingly, based on the current record, Petitioner demonstrates a” slip op. at 63
- Novelty / Anticipation (§102) › Priority / effective filing date / continuation supportReference is prior artDecided for petitioner
“To satisfy the written-description requirement, the inventor must have possession of the claimed invention as interpreted to encompass an allegedly infringing product. See Rivera, 857 F.3d at 1319–22; ICU Med., 558 F.3d at 1372–73, 1377–79. For purposes of the written-description requirement, the “invention” is “whatever is now claimed.” Vas-Cath, 935 F.2d at 1564 (emphasis omitted). Based on the current record, and as Petitioner asserts, LTE band 12 was not available for “use with mobile communications” or “use in any cellular communication, let alone LTE or 4G communication,” as of the ’429 application’s December 21, 2006, filing date. See Ex. 1007 ¶¶ 229, 231; Pet. 76–77. For instance, a Federal Communications Commission report adopted on July 31, 2007, notes that the 698-806 MHz spectrum “currently is occupied by television broadcasters in TV Channels 52-69.” Ex. 1045, 1, 3; see Ex. 1007 ¶ 231. The 698-806 MHz spectrum includes LTE band 12 with 698-716 MHz for uplink and 728-746 MHz for downlink. See Ex. 1026, 11 (Table 1); Ex. 1039, 498 (Table 20.1). At this stage of the proceeding, Patent Owner does not dispute that as of July 31, 2007, the 698-806 MHz spectrum was “occupied by television broadcasters in TV Channels 52-69.” See Prelim. Resp. 2–3, 23–30; Prelim. Sur-reply 5. Thus, based on the current record, Petitioner demonstrates a reasonable likelihood that as of the ’429 application’s December 21, 2006, filing date, the ’429 application did not “reasonably convey[] to those skilled in the art that the inventor had possession” of “an antenna configured to send or receive signals in the 698-806 MHz spectrum,” including LTE band 12 that Patent Owner relies on in the Geotab litigation, for “communication with any ‘4G communication standard’ because those frequencies were not usable for any mobile device communications at the time of filing.” See Pet. 78 (emphasis omitted); Ex. 1007 ¶¶ 231, 233–234, 236–237; Ex. 1045, 1, 3; Ariad, 598 F.3d at 1351. Accordingly, based on the current record, Petitioner demonstrates a” slip op. at 63
§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · KSR · GrahamPatents in suitUS 11,349,200 - PTAB · Oct 9, 2025 · IPR2025-00847 · APJ Brian D Range · IPR · Institution
Instituted IPR on claims 1–11 because Petitioners showed a reasonable likelihood of proving at least one challenged claim unpatentable across the asserted grounds.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“unless the information presented in the petition “shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” The following findings of fact and conclusions of law are not final, but are made for the sole purpose of determining whether Petitioners meet the threshold for initiating review. Any final decision shall be based on the full trial record, including any response timely filed by Patent Owner. Any arguments not raised by Patent Owner in a timely-filed response may be deemed waived. For the reasons stated below, we determine that Petitioner has established a reasonable likelihood that it would prevail with respect to at least one claim. We hereby institute an inter partes review as to claims 1–11 of the ’847 patent based upon Petitioners’ asserted grounds of unpatentability.” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“would have had a master’s degree in electrical engineering, physics, chemistry, materials science, or a related field and three years of work experience in semiconductor manufacturing, such as, for example, in integrated circuit device (or transistor) design and/or manufacturing,” and “[a]dditional relevant education could substitute for professional experience, and significant work experience or training could substitute for formal education.” Pet. 11 (citing Ex. 1003 ¶ 38). Patent Owner does not dispute the level of ordinary skill in the art. See generally Prelim. Resp. For purposes of this Decision, we adopt Petitioner’s proposal as reasonable and consistent with the ’847 patent specification and the prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art). slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached
“Petitioner does not propose any claim constructions, except to explain that the claim 7 limitation “the spacer further comprises an offset spacer, positioned between the gate and the spacer,” is “satisfied if one layer (an ‘offset spacer’) of the claimed ‘spacer’ lies between another layer of the ‘spacer’ and the gate.” Pet. 11. Patent Owner does not dispute Petitioner’s assertions or offer any claim constructions. See generally Prelim. Resp. Because resolution of Petitioner’s proposed construction is unnecessary to our analyses for purposes of this decision, we do not address the proposal here. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). We do not discern a need to construe any other claim language at this juncture because doing so would have no effect on our analyses below of Petitioner’s asserted grounds and will not assist in resolving the present controversy between the parties. See Realtime Data, LLC, 912 F.3d at 1375.” slip op. at 8
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Instituted
“a. Claim 1 Petitioner contends that claim 1 is anticipated by Lan or, alternatively, obvious in view of Lan. Pet. 18–26. Petitioner explains how Lan teaches or suggests each recitation of claim 1, and Petitioner’s position is supported by adequate evidence for institution. Id. (citing, e.g., Ex. 1003 ¶¶ 100–125). Petitioner, for example, persuasively compares the structure of Figure 12 of Lan to each limitation of claim 1. Id. Patent Owner does not dispute Petitioner’s contentions except to argue that Lan (and the Petition’s other asserted references) “Do Not Mention, Describe, or Concern ‘Raised Epitaxial Layers.’” Prelim. Resp. 22–24. Patent Owner does not persuasively undermine Petitioner’s position.” slip op. at 13
Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 7,745,847 - PTAB · Oct 6, 2025 · IPR2025-00611 · APJ Christopher L Ogden · IPR · Institution
The Board instituted IPR of claims 1–10, 12, 13, 19, and 20 on all petition grounds after finding a reasonable likelihood that claim 1 was obvious over Douglas and Mark.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“A claim is unpatentable under § 103 “if the differences between the claimed invention and the prior art are such that the claimed invention as a whole would have been obvious before the effective filing date of the claimed invention to a person having ordinary skill in the art to which the claimed invention pertains.” 35 U.S.C. § 103; see KSR Int’l Co. v. Teleflex Inc., 550 U.S. 398, 406 (2007). When a ground in a petition is based on a combination of references, we consider “whether there was an apparent reason to combine the known elements in the fashion claimed by the patent at issue.” KSR, 550 U.S. at 418 (citing In re Kahn, 441 F.3d 977, 988 (Fed. Cir. 2006)).” slip op. at 8
- Skill levelSkill level petitioner adoptedDecided for petitioner
“The parties agree that experience could substitute for a degree, and vice versa. Pet. 3 (citing Ex. 1003 ¶¶ 19–21); Prelim. Resp. 9. The parties’ proposed levels of ordinary skill are substantially similar. Although we discern no difference in the outcome of this decision from choosing one over the other, we adopt Petitioner’s proposal for this decision. Only Petitioner’s proposed level is supported by testimonial evidence on the preliminary record, and it appears to be consistent with the problems addressed in the ’774 patent. See Ex. 1001, 1:16–52. Therefore, we adopt Petitioner’s proposal for this decision.” slip op. at 7
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“CLAIM CONSTRUCTION B. In an IPR, we construe a patent claim “using the same claim construction standard that would be used to construe the claim in a civil action under 35 U.S.C. 282(b).” 37 C.F.R. § 42.100(b). This generally includes “construing the claim in accordance with the ordinary and customary meaning of such claim as understood by one of ordinary skill in the art and the prosecution history pertaining to the patent.” Id. The ordinary and customary meaning of a claim term “is its meaning to the ordinary artisan after reading the entire patent,” and “as of the effective filing date of the patent application.” Phillips, 415 F.3d at 1313, 1321. Neither Petitioner nor Patent Owner argues that we need to construe any claim terms explicitly. See Pet. 2–3; Prelim. Resp. 9. However, the parties’ positions depend on interpreting the claim language in a particular way, and we discuss the relevant claim language below in the context of the parties’ arguments regarding the prior art. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 7
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundInstituted
“At this stage, we find Petitioner’s arguments persuasive and disagree with Patent Owner. Patent Owner appears to equate a “fabrication profile” with a toolpath description, but nothing in the plain language of claim 1 supports that narrow interpretation. The ’774 patent describes a “fabrication profile” broadly and states that the profile can simply “include the dictionary [of configuration information],” or be “used to determine which machineready representation is available or suitable for a target printer.” Ex. 1001, 23:49–52. The preliminary evidence suggests that Douglas’s “operational parameters” would count as a “fabrication profile” because it is “the basis for generation of a machine-ready representation of the three-dimensional model that is executable on the target printer.” Id. at 23:37–39; see infra Section III.C.8. We also disagree that Petitioner’s argument is impermissible hindsight, because it is based on the disclosures in Douglas and Mark, and Petitioner has articulated a sufficiently persuasive reason to combine those references without referring to the ’774 patent itself. See In re McLaughlin, 443 F.2d 1392, 1395 (CCPA 1971) (an obvious rationale is not improper hindsight if it “takes into account only knowledge which was within the level of ordinary skill at the time the claimed invention was made and does not include knowledge gleaned only from applicant’s disclosure”). Finally, Petitioner appears to rely on Mark for providing a particular example of a fabrication profile, not to replace Douglas’s overall system in which the 3D printer can receive “operational parameters” rather than just G-code. See Pet. 8–10, 17–23; see also Ex. 1005 ¶ 41 (the print queue, which stores tool instructions, may be maintained locally on printers 204 or on print servers 208); see In re Mouttet, 686 F.3d 1322, 1332 (Fed. Cir. 2012) (“[A] determination of obviousness based on teachings from multiple references does not require an actual, physical substitution of elements.” (citing In re Etter, 756 F.2d 852, 859 (Fed. Cir. 1985) (en banc))).” slip op. at 19
Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,886,774 - AT&T Mobility LLC / AT&T Services Inc. et al. v. Daingean Technologies Ltd.No claims unpatentablePTAB · Jul 14, 2025 · IPR2024-00402 · APJ Mary C Hoffman · IPR · Final written decision
The Board granted Patent Owner’s revised non-contingent motion to amend, canceling claims 1–4 and substituting claims 7 and 8, which Petitioner did not prove unpatentable.
RulingsFinal written decision- PTAB / AIA Trials › Motions to amend / substitute claimsMotion to amend, grantedGranted
“whether the motion to amend meets the statutory and regulatory requirements set forth in 35 U.S.C. § 316(d) and 37 C.F.R. § 42.121.” See Lectrosonics, Inc. v. Zaxcom, Inc., IPR2018-01129, Paper 15 at 4 (PTAB Feb. 25, 2019) (precedential). A “patent owner bears the burden of persuasion to show, by a preponderance of the evidence, that the motion to amend complies” with the applicable statutory and regulatory requirements. 37 C.F.R. § 42.121(d)(1). Specifically, a patent owner must demonstrate the following: (1) the amendment proposes a reasonable number of substitute claims; (2) the amendment responds to a ground of unpatentability involved in the trial; (3) the amendment does not seek to enlarge the scope of the claims of the patent; and (4) the amendment does not introduce new matter. See 35 U.S.C. § 316(d); 37 C.F.R. § 42.121(a)–(b). For the reasons explained below, Patent Owner satisfies its burden of persuasion to show that the amendments comply with the applicable statutory and regulatory requirements.” slip op. at 8
- Skill levelSkill level patent owner adoptedDecided for patent owner
“Both parties rely on expert testimony for their respective positions relating to the number of years of experience needed to attain ordinary skill, but neither expert cites supporting evidence for their testimony. See Ex. 1002 ¶ 33; Ex. 2002 ¶ 15. Our decision is the same regardless of whether the length of experience is two years or three. We find Patent Owner’s proposed “wireless communications” is more consistent with the ’958 patent than Petitioner’s proposed “telecommunication,” which encompasses a variety of technologies including, e.g., landline and wireless telephones, cable, and satellite. See Ex. 1001, 1:11–62 (describing the invention in terms of wireless communications). Accordingly, we adopt a modified version of Petitioner’s proffered level of ordinary skill in the art, substituting “wireless communications” for “telecommunication.” Neither party, moreover, indicates the overall result would change based on a different definition.” slip op. at 18
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner
“We agree with Patent Owner that the recited second type SIBs exclude first type SIBs. The plain meaning of “first type” and “second type” indicates that the first type and second type are different in kind. RMTA 22 (App. A). Our interpretation is consistent with the Specification, which explains that second type SIBs exclude first type SIBs. As Patent Owner points out, the ’958 patent discloses “first type of system information (1TYP SIB) is . . . essential . . . for initial system access” and “second type of system information (2TYP SIB) is nonessential system information . . . defined as all other types of information, and thus excludes the [] information required for initial access.” Id. at 11–12 (citing Ex. 1001, 8:34– 46); see also Ex. 1001, Abstract (interchangeably using the terms second type and non-essential). Despite Petitioner’s argument that this disclosure is non-limiting and directed to a disclaimed example embodiment (Opp. 8–9), Petitioner could not identify any embodiment, among the approximately forty disclosed embodiments, describing something other than the first type SIB being essential information and the second type SIB being non-essential information. Tr. 22:18–26. Even the Petition acknowledges that “the ’958 Patent further classifies a second type of system information, the ‘non-essential’ SI, which is defined as all other types of information excluding that first type of information required for initial access.” Pet. 5. Furthermore, the prior art of record suggests that a person of ordinary skill would have understood second type SIBs exclude first type SIBs. See Ex. 1008 ¶ 48 (describing two categories of system information, “essential SI” and “Other SI”). Patent Owner’s expert also understood the recited first and second type SIBs as being mutually exclusive. See Ex. 1011, 49:10–13. For the above reasons, we do not agree with Petitioner that the recited second type SIB lacks any requirements, nor do we interpret claims 7 and 8 such that the first type SIB could be a second type SIB.” slip op. at 19
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable
“(d) Limitation 7h: Analysis We agree with Patent Owner that Petitioner’s arguments with respect to limitation 7h are insufficient because they fail to address the limitation as written and improperly incorporate previous arguments by reference. For example, Petitioner did not map the recited “group identifier” when opposing Patent Owner’s Revised Motion to Amend. See Opp. 16–17. In its Sur-reply, Petitioner contends that limitation 7h’s requirement of transmitting the group identifier was previously “set out in Patent Owner’s prior papers,” but does not refer to any specific papers or exhibits. Pet. Surreply 11–12. We decline to search for and piece together Petitioner’s arguments and evidence to develop a persuasive theory of unpatentability. See 37 C.F.R. section 42.6(a)(3). Petitioner similarly failed to address adequately where Lee discloses or suggests the recited “compressed format” and “plural parameters.” See Opp. 16–17. Aside from the above concerns, we also do not see sufficient explanation with respect to limitation 7h’s requirement that the transmitting by broadcast be based on a comparison of the value tag. Petitioner argues that, because Patent Owner does not dispute limitation 7g, “it would have been obvious to a POSITA to use the same value tag[] to determine the system information broadcast in Lee’s compressed format embodiment.” Pet. Sur-reply 12. This conclusory statement is not supported by any citations to evidence and was improperly introduced in the Sur-reply. Moreover, whether it was obvious to determine what system information is broadcast is not commensurate with the claim scope because limitation 7h requires that the broadcasting (not the broadcast content) be based on a comparison of the value tag. See supra III.B.4 and IV.B. Further, we are not persuaded that Lee’s transmitting by broadcast is” slip op. at 26
Patent outcomesUS 10,841,958 not shown unpatentableClaim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · KSR · Graham · NautilusPatents in suitUS 10,841,958 - Apple Inc. v. Geoscope Technologies Pte. Ltd.All claims unpatentablePTAB · May 7, 2025 · IPR2024-00031 · APJ Annette R Reimers · IPR · Final written decision
Claims 16–20, 24, 26, and 27 are unpatentable: claims 16, 19, 20, 24, and 27 are anticipated by Bhattacharya, and all challenged claims are obvious over Bhattacharya and Spain.
RulingsFinal written decision- Skill levelSkill level patent owner adoptedDecided for patent owner
“We agree with Patent Owner for the following reasons. First, Patent Owner’s definition is consistent with our determination in IPR2023-01210, which involved the same ’358 patent, and Petitioner does not explain sufficiently why we should adopt a different definition. See generally Pet. Reply.” slip op. at 8
- Expert testimonyPetitioner expert creditedDecided for petitioner
“Sundaresan Declaration, Dr. Sundaresan implied agreement with the POSITA definition based on its inclusion in a signed declaration.” Pet. Reply 15. We agree with Petitioner. Although Dr. Sundaresan does not state explicitly that the proposed definition of the ordinary skill in the art is his opinion, we are persuaded that the manner in which the definition is set forth in his declaration indicates that he agrees with the definition. In this case, Patent Owner attempts to make much of Dr. Sundaresan’s statement that he had been informed of the qualifications of a person of ordinary skill in the art. See PO Resp. 42–44. Dr. Sundaresan’s testimony, however, set forth this understanding of the requisite level of skill in the art (Ex. 1003 ¶ 8). In his supplemental declaration, Dr. Sundaresan further testifies that: I agreed with this POSITA definition when preparing the Declaration, and I continue to hold the opinion that the POSITA definition is both correct and appropriate based on the disclosures of the ’358 patent and the prior art analyzed in the Declaration. Ex. 1055 ¶ 17. Dr. Sundaresan further testifies that “[i]f I did not agree with the POSITA definition, then it would not have been included [] in paragraph 8 of the Declaration.” Id. ¶ 18. Dr. Sundaresan’s inclusion of the definition of the level of ordinary skill in his original declaration indicates that he” slip op. at 13
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner
“explained below, we agree with Petitioner that Patent Owner’s additional requirement of evaluating the calibration data to determine the boundaries of the area represented by a grid point should not be included in the construction of either “grid point” or “non-uniform grid point.” Instead, based on the full record, we discern no reason to alter our prior construction of “grid point” as “a point associated with representative calibration data for an area” and maintain that construction for this Final Written Decision. The construction of “grid point” we adopt is supported by the Specification of the ’358 patent. Namely, the ’358 patent discloses that “[i]n general, a non-uniform grid point (NUG) may represent the signal characteristics and/or calibration data over a given region,” and “NUGs district court identified the second quoted passage, which is identically recited in the ’104 patent (see Ex. 2018, 3:50–60) as “provid[ing] a clear indication of the meaning of ‘grid point.’” Ex. 2012, 19 (emphasis added). We agree with the district court’s analysis. Although the ’358 patent does not explain how a generic “grid point” might differ from the described “nonuniform grid point,” we do not find this distinction pertinent to construing “grid point” in this case because neither party raises this issue. Also, based on the claim wording “non-uniform grid point,” a “non-uniform grid point” is a type of grid point. See Pet. Reply 4 (explaining why that plain meaning supports Petitioner’s proposed construction). Furthermore, the district court construed “grid point” only, not “non-uniform grid point.” Ex. 2012, 18–20.” slip op. at 26
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable
“Based on the entire trial record, we agree with Petitioner’s analysis with supporting evidence and credit Dr. Sundaresan’s testimony supporting Petitioner’s position. See Pet. 20–37. Thus, we determine that Bhattacharya discloses the recitations of claim 15. b. Remaining Claims 16, 19, 20, 24, and 27 Claims 16, 19, 20, 24, and 27 depend from claim 15. Ex. 1001, 13:19–21, 12:30–36, 12:52–55; 12:63–67. Petitioner accounts for the limitations recited in each of claims 16, 19, 20, 24, and 27. Pet. 37–42. Patent Owner does not offer any arguments specifically addressing the limitations of claims 16, 19, 20, 24, and 27. See PO Resp. passim. Petitioner shows, by a preponderance of the evidence, that each element of claims 16, 19, 20, 24, and 27 is disclosed by Bhattacharya.” slip op. at 41
Patent outcomesUS 8,400,358 unpatentableClaim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 8,400,358
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.