• Shenzhen Tuozhu Technology Co., Ltd. v. Stratasys, Inc.All claims unpatentable
  PTAB · Sep 28, 2026 · IPR2025-00611 · APJ Christopher L Ogden · IPR · Final written decision

  Claims 1–10, 12, 13, 19, and 20 are unpatentable under § 103 over the stated Douglas–Mark and Hamilton-based grounds.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “The parties agree that experience could substitute for a degree, and vice versa. Pet. 3; PO Resp. 10. The parties’ proposed levels of ordinary skill are substantially similar. For this decision, as in the Institution Decision, we adopt Petitioner’s proposed level, which is supported by credible testimonial evidence and is consistent with the problems addressed in the ’774 patent. See Ex. 1001, 1:16–52. Our decision would be the same, however, if we were to adopt Patent Owner’s proposal.” slip op. at 7

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Other

    “Neither Petitioner nor Patent Owner argues that we need to construe any claim terms explicitly. See Pet. 2–3; PO Resp. 10. However, the parties contest two material claim-construction issues which we address below. To the extent that the parties’ positions depend on interpreting other claim language in a particular way, we discuss the relevant claim language below in the context of the parties’ arguments regarding the prior art.” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “We disagree with Patent Owner that a person of ordinary skill in the art would have understood that limitation 1.2 must be performed before limitations 1.3 or 1.4. See Ex. 1001, 35:21–24. See Interactive Gift Exp., Inc. v. Compuserve Inc., 256 F.3d 1323, 1342 (Fed. Cir. 2001) (“Unless the steps of a method actually recite an order, the steps are not ordinarily construed to require one.” (citing Loral Fairchild Corp. v. Sony Corp., 181 F.3d 1313, 1322 (Fed. Cir. 1999)). The evidence suggests that a “target printer” is any printer that is ultimately selected for fabricating the object, and such a printer could send its configuration information either before or after that determination is made in limitation 1.2. This interpretation does not render the word “target” meaningless. At some point, a printer must be determined to be the target printer, which is the one intended to ultimately fabricate the three-dimensional object. But the target printer still exists, and is capable of being queried, before that determination is made. We find the examples in the ’774 patent pertinent to this question. The ’774 patent states that “the target printer may include more than one printer.” Ex. 1001, 18:66–67. In discussing the step of “query target printer for properties 306” (Fig. 3A), the ’774 patent states that “[i]n one aspect, numerous queries are sent to numerous printers, e.g., for use in selecting one or more of the printers as the target printer.” Id. at 19:8–10. Alternatively, “the query is sent to a printer that is not necessarily the target printer as described herein, e.g., when the query or information received from a response to the query is used for the selection of the target printer.” Id. at 19:11–14. Importantly, the second embodiment states that the queried printer “is not necessarily the target printer,” suggesting that the queried printer could be the target printer even before it is determined to be such. Id. at 19:11–12 (emphasis added). Based on the evidence of record, a person of ordinary skill in the art would have understood that the “target printer” can be determined after the query recited in limitation 1.3 or the reception of configuration information recited in limitation 1.4. Thus, the evidence does not impose an ordering between limitations 1.2 and 1.3 or between limitations 1.2 and 1.4. The evidence also does not support Patent Owner’s argument that the two reverse-order examples in the ’774 patent are unclaimed embodiments.” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightMotivation foundDecided for petitioner

    “We disagree that Petitioner’s arguments are based on impermissible hindsight, because they are based on the disclosures in Douglas and Mark, and Petitioner has articulated a persuasive reason to combine those references without referring to the ’774 patent itself, as we discuss below. See In re McLaughlin, 443 F.2d 1392, 1395 (CCPA 1971) (an obvious rationale is not improper hindsight if it “takes into account only knowledge which was within the level of ordinary skill at the time the claimed invention was made and does not include knowledge gleaned only from applicant’s disclosure”).” slip op. at 29

  Patent outcomesUS 11,886,774 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 11,886,774
• Intel Corporation v. Advanced Cluster Systems, Inc.All claims unpatentable
  PTAB · Sep 23, 2026 · IPR2025-00915 · APJ Arthur M Peslak · IPR · Final written decision

  Claims 1–30 are unpatentable: claims 1–3, 5–16, and 18–30 as obvious over Menon, Trefethen, RS6000, and MPIref; claims 4 and 17 over those references plus POEref.

  RulingsFinal written decision

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundTeaching away not foundDecided for petitioner

    “Ex. 1163 ¶ 37 (citing Ex. 1003 ¶ 71; Ex. 1005, 1–3). We credit Dr. Bajaj’s testimony which is unrebutted and supported by the record. We, thus, agree with Dr. Bajaj’s reasoning which is based on Menon. We further agree with Dr. Bajaj’s conclusion that Menon does not teach away from the combination with Trefethen. Id. ¶ 75. Menon’s description of building on and enhancing the teachings of Trefethen—the earlier work of the same research group at Cornell—by adding MEX routines to achieve high-performance parallel computing and extensibility for MATLAB, demonstrates a classic motivation for a POSITA to combine. RS6000 is specifically referenced in Menon-Trefethen and adds operational details of the parallel operating platform that teach a POSITA how to implement the MultiMATLAB system with a reasonable expectation of success. Considering Menon as a whole, these facts are inconsistent with Patent Owner’s teaching away arguments. For these reasons, Patent Owner’s teaching away argument is unavailing. Motivation to Combine Conclusion We have reviewed Petitioner’s evidence and contentions which we” slip op. at 42

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable

    “For the foregoing reasons, Petitioner establishes by a preponderance” slip op. at 79

  Patent outcomesUS 11,563,621 unpatentable
  § 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,563,621
• Posco Co., Ltd. v. ArcelormittalAll claims unpatentable
  PTAB · Jul 16, 2026 · IPR2025-00371 · APJ Brian D Range · IPR · Final written decision

  Claims 1–25 are unpatentable as obvious under § 103 over the asserted combinations of Takagi, Cornette, Suehiro, GMW14400, Laurent, and Vaissiere.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art (POSITA) “would have had an undergraduate degree in materials science, manufacturing engineering, mechanical engineering, or equivalent knowledge, training, or experience, with two years of experience working in metallurgy.” Pet. 6 (citing Ex. 1003 ¶ 15). Patent Owner does not challenge Petitioner’s definition of a POSITA for this proceeding. PO Resp. 8. Because the parties agree and because Petitioner’s proposal is reasonable and consistent with the ’227 patent specification and the prior art, we adopt Petitioner’s proposal. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art).” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for patent owner

    “1. superficial layer The only independent claim at issue, claim 1, recites a “Superficial layer.” Ex. 1001, 15:6. Patent Owner argues that, based on plain and ordinary meaning, the term “superficial layer” refers to a “surface layer” or “top layer.” PO Resp. 8–9. Petitioner does not dispute this construction. See Pet. Reply 21–22 (arguing that the relevant layer of the Suehiro reference is a superficial layer because it is outermost and present at the surface). Because the parties are in agreement and because that agreement is consistent with plain language, claim language, and the ’227 specification, we construe “superficial layer” as referring to a surface layer or top layer.” slip op. at 10

  • Claim Construction › Extrinsic evidence (dictionaries, experts)Term construed petitioner constructionDecided for petitioner

    “defined stoichiometry” (Ex. 2037, 527) but the word may also be a “generic term for phases . . . which may have a narrow or extended compositional stability range” (id.). The first glossary meaning is consistent with Patent Owner’s position. The second, broader, glossary meaning is consistent with Petitioner’s position. Some of the extrinsic sources before us support the broad definition, and some support the narrow definition. See PO Sur-Reply 3–4 (arguing that Dr. Miles admitted that various treatises distinguish intermetallic compounds from alloys and solid solutions). Thus, neither Dr. Miles or Dr. Raabe is “wrong scientifically” in how they use the term “intermetallic” in this proceeding. Id. at 2 (noting that Dr. Miles agreed that Dr. Raabe’s construction is not wrong scientifically). As explained below, however, only one of these meanings is appropriate here. To decide which possible meaning applies to the ’227 patent, we focus on the patent claims and specification. Claim 1 indicates that the intermetallic layer has a “mean composition” (emphasis added). Ex. 1001, 15:1–10. This indicates, albeit weakly, that iron composition across the layer may vary rather than having ordered stoichiometry—consistent with Petitioner’s position. The specification also indicates that “intermetallic alloying” is a possibility—again, consistent with Petitioner’s position. Ex. 1001, 2:47–50. Meanwhile, nothing in the ’227 specification explicitly (or implicitly) suggests that “intermetallic layer” must be limited to elements atomically joined with defined stoichiometry in an ordered crystal structure. We also find that Dr. Miles’s testimony regarding the meaning of “intermetallic” is more credible than Dr. Rabbe’s testimony. Dr. Rabbe, in deposition, stated that Figure 2 of the challenged patent “does not show a layer that meets [his] construction of intermetallic.” Ex. 1078, 129:21–24. The ’227 patent, however, states that Figure 2 includes an “Al-rich Intermetallic layer.” Ex. 1001, Fig. 2, 3:60–64 (“FIG 2. Illustrates a coating … which does not correspond to the invention. This succession of layers (interdiffusion layer and intermetallic layer) yields inferior results in resistance spot welding.”). Also, Dr. Raabe previously referred to a layer of Takagi as having “intermetallic phase layering and structure.” Pet. Reply 4 (citing Ex. 1076 ¶ 166; Ex ¶ 1075, 17) (emphasis omitted). Thus, Dr. Raabe’s construction of “intermetallic” for this proceeding does not fully account for the ’227 patent usage of the word “intermetallic” and does not fully account for Dr. Raabe’s prior usage of the word “intermetallic.” Patent Owner argues that Petitioner’s construction “erases the meaningful distinction” between the claimed layers. PO Resp. 11. Patent Owner further argues that Petitioner’s construction renders the word “intermetallic” superfluous because allowing the intermetallic layer to be “merely a multi-element alloy erases the meaningful distinction among these layers.” Id. We disagree. The word intermetallic serves to require that the layer be composed of two or more metals or a metal and a metalloid. The word intermetallic also serves as a label to differentiate each of the four claimed layers. For example, in claim 1, the word “intermetallic” is used much like the words “interdiffusion” and “intermediate” to give each of the four layers (each having differently mean compositions) different labels.” slip op. at 16

  • Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication establishedDecided for petitioner

    “Because IHS was a company that created an online database with the purpose of providing (selling) standards including General Motors standards to the public, we determine that a person of ordinary skill in the art would have known to look to this database and would have been able to find GMW14400. Patent Owner presents no evidence to the contrary. Because a preponderance of the evidence supports Petitioner, we determine Petitioner establishes GMW14400 is qualifies as prior art.” slip op. at 21

  Patent outcomesUS 11,326,227 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,326,227
• Posco Co., Ltd. v. ArcelormittalAll claims unpatentable
  PTAB · Jul 16, 2026 · IPR2025-00370 · APJ Brian D Range · IPR · Final written decision

  Claims 1–30 are unpatentable as obvious under § 103 over the asserted combinations of prior art.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art (POSITA) “would have had an undergraduate degree in materials science, manufacturing engineering, mechanical engineering, or equivalent knowledge, training, or experience, with two years of experience working in metallurgy.” Pet. 6 (citing Ex. 1003 ¶¶ 13–16). Patent Owner does not challenge Petitioner’s definition of a POSITA for this proceeding. PO Resp. 8. Because the parties agree and because Petitioner’s proposal is reasonable and consistent with the ’602 patent specification and the prior art, we adopt Petitioner’s proposal. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art).” slip op. at 8

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

    “1. superficial layer All independent claims at issue, claims 1, 21, and 24, recite a “superficial layer.” Ex. 1001, 15:11, 16:60, 17:21. Patent Owner argues that, based on plain and ordinary meaning, the term “superficial layer” refers to a “surface layer” or “top layer.” PO Resp. 8–9. Petitioner does not dispute this construction. See Pet. Reply 21–22 (arguing that the relevant layer of the Suehiro reference is a superficial layer because it is outermost and present at the surface). Because the parties are in agreement and because that agreement is consistent with plain language, claim language, and the ’602 specification, we construe “superficial layer” as referring to a surface layer or top layer.” slip op. at 10

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “defined stoichiometry” (Ex. 2037, 527) but the word may also be a “generic term for phases . . . which may have a narrow or extended compositional stability range” (id.). The first glossary meaning is consistent with Patent Owner’s position. The second, broader, glossary meaning is consistent with Petitioner’s position. Some of the sources before us support the broad definition, and some support the narrow definition. See PO Sur-Reply 3–4 (arguing that Dr. Miles admitted that various treatises distinguish intermetallic compounds from alloys and solid solutions) Thus, neither Dr. Miles or Dr. Raabe is “wrong scientifically” in how they use the term “intermetallic” in this proceeding. Id. at 2 (noting that Dr. Miles agreed that Dr. Raabe’s construction is not wrong scientifically). As explained below, however, only one of these meanings is appropriate here. To decide which possible meaning applies to the ’602 patent, we focus on the patent claims and specification. The claims indicate that the intermetallic layer has a “mean iron composition” (emphasis added). Ex. 1001, 15:6–10. This indicates, albeit weakly, that the iron composition across the layer may vary rather than having ordered stoichiometry— consistent with Petitioner’s position. The specification also indicates that “intermetallic alloying” is a possibility—again, consistent with Petitioner’s position. Id. at 2:50–54. Meanwhile, nothing in the ’602 specification explicitly (or implicitly) suggests that “intermetallic layer” must be limited to elements atomically joined with defined stoichiometry in an ordered crystal structure. We also find that Dr. Miles’s testimony regarding the meaning of “intermetallic” is more credible than Dr. Raabe’s testimony. Dr. Raabe, in deposition, stated that Figure 2 of the challenged patent “does not show a layer that meets [his] construction of intermetallic.” Ex. 1078, 129:21–24. The ’602 patent, however, states that Figure 2 includes an “Al-rich Intermetallic layer.” Ex. 1001, Fig. 2, 3:57–61 (“FIG 2. Illustrates a coating . . . which does not correspond to the invention. This succession of layers (interdiffusion layer and intermetallic layer) yields inferior results in resistance spot welding.”). Also, Dr. Raabe previously referred to a layer of Takagi as having “intermetallic phase layering and structure.” Pet. Reply 4 (citing Ex. 1076, 166; Ex. 1075, 17) (emphasis omitted). Thus, Dr. Raabe’s definition of “intermetallic” does not fully account for the ’602 patent usage of the word “intermetallic” and does not fully account for Dr. Raabe’s prior usage of the word “intermetallic.” Patent Owner argues that Petitioner’s construction “erases the meaningful distinction” between the claimed layers. PO Resp. 11. Patent Owner further argues that Petitioner’s construction renders the word “intermetallic” superfluous because allowing the intermetallic layer to be “merely a multi-element alloy erases the meaningful distinction among these layers.” Id. We disagree. The word intermetallic serves to require that the layer be composed of two or more metals or a metal and a metalloid. The word intermetallic also serves as a label to differentiate each of the four claimed layers. For example, in claim 1, the word “intermetallic” is used much like the words “interdiffusion” and “intermediate” to give each of the four layers (each having differently defined mean iron compositions) different labels.” slip op. at 16

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner

    “have had reason to combine teachings of Takagi and Cornette with a reasonable expectation of success. Pet. 11–20 (citing, e.g., Ex. 1003 ¶¶ 28– 42; Ex. 1016 ¶ 35; Ex. 1014, 9; Ex. 1025, 5:17–20; Ex. 1026, 7; Ex. 1034 ¶ 13). In particular, Petitioner argues that Takagi discloses a pre-coating thickness of 10–20 µm but does not explicitly disclose a post hot-stamping coating thickness corresponding to the pre-coating thickness. Pet. 11. Cornette teaches that the hot-stamping thickness causes coating expansion from 25 µm to about 40 µm, an increase of 60%. Id. (citations omitted). Petitioner and Dr. Miles reason that, when hot stamping Takagi’s product, the thickness would be 32 µm. Id. (citing Ex. 1003 ¶ 32); see also Pet. Reply 20–21. Thus, Patent Owner argues that Cornette evidences Takagi’s finally coating thickness without requiring modification of Takagi. Petitioner further argues that Takagi and Cornette teach that post hot- stamping thickness could be varied and optimized as a result effective variable. Id. at 12–13; see also Pet. Reply 17–18. Cornette teaches, for example, that “[t]he average [pre-coating] layer thickness showing the best compromise between corrosion protection and weldability is 25 µm” and links this pre-coating thickness to a final thickness of “about 40 µm at the steel surface.” Ex. 1014, 9. Petitioner also argues that it would have been obvious to fill in other details of Takagi including, for example, selecting USIBOR 1500 steel, based on the teachings of Cornette. Pet. 14. Patent Owner argues that there is no reason to combine Takagi with the teachings of Cornette. PO Resp. 26. Patent Owner makes seven related arguments. Patent Owner first argues that the Petitioner’s position is speculative and lacks basis. Id. at 26–27. We disagree. Cornette evidences a final coating thickness for Takagi, and the references also suggest that final coating thickness is result effective. Second, Patent Owner argues that there would have been no incentive to seek a motivation to seek a thicker coating post-hot stamping. Id. at 28– 35. This argument does not undermine Petitioner’s position that Takagi, by itself, would have reached a thicker coating after stamping as evidenced by Cornette. Pet. 11–12. Petitioner takes the position, with evidence, that practice of Takagi alone would reach the recited thickness. No motivation to modify Takagi is required under this position.” slip op. at 25

  Patent outcomesUS 10,961,602 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 10,961,602
• Google LLC / Lenovo (United States) Inc. v. Ericsson ABAll claims unpatentable
  PTAB · Mar 23, 2026 · IPR2025-00003 · APJ Norman H Beamer · IPR · Final written decision

  Claims 1–8, 10, 12, 14, and 16–20 are unpatentable under § 103; the Board denied Patent Owner’s revised motion to amend.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “[W]ould have had a bachelor’s degree in computer science, computer engineering, electrical engineering, or a related field, and 2–3 years of practical engineering experience relating to information security systems that employ cryptographic keys to encrypt/decrypt digital data. Additional education could substitute for professional experience, or significant experience in the field could substitute for formal education. Ex. 1003 ¶ 41. Patent Owner agrees with Petitioner’s expert regarding the level of ordinary skill in the art. RMTA 19. Patent Owner’s declarant, Dr. Villasenor, notes that “obviousness must be viewed from the perspective of one of ordinary skill in the field of information security using cryptographic keys for encryption and decryption of digital data, and my opinions are rendered on the basis of the definition of the ordinary artisan set forth in the Petition in view of that further clarification.” Ex. 2010 ¶ 19. Based on a review of the record, we adopt Petitioner’s proposed level of ordinary skill in the art because it is consistent with the evidence of record, including the asserted prior art and ’178 patent specification. Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 11

  • Expert testimonyOther

    “In reply, Patent Owner substantially repeats its arguments against Petitioner’s reliance on Peterka for the claim 1 content encryption key identifiers requirements. Reply RMTA 8–9 (citing Ex. 1005 ¶ 121; Ex. 2010 ¶¶ 89, 93–95); see RMTA 14–15. We are not persuaded by these arguments for the reasons discussed in Section III.D.2.e)(2) above.” slip op. at 65

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner

    “Patent Owner argues that there was no motivation to combine Peterka with Suzuki because Petitioner has argued that “Peterka can already identify content keys by using the allegedly unique sequence numbers or time stamps assigned to each message carrying a single content key.” PO Resp. 41–42 (citing Pet. 25). Patent Owner also challenges motivation to combine Suzuki because it “is not directed to a pay-by-time, pay-per-view, or subscription distribution model, in which a content key grants access to content that different clients must individually decide to purchase in discrete units or increments.” Id. at 36–37. Petitioner responds that, because Peterka disclosed alternative embodiments that did not use sequence numbers or time stamps to identify EMM/ECM messages, one of ordinary skill would have been motivated specifically assign identifications to individual keys as taught in Suzuki. Reply 22 (citing Pet. 26). Petitioner also argues that whether Suzuki was directed to unpurchased content was irrelevant, because Suzuki is cited to show multiple key responses were conventional. Id. at 19–20. Patent Owner does not otherwise specifically address the issue of motivation to combine Peterka, Suzuki, and Bocharov. See generally PO Resp. Nonetheless the burden remains on Petitioner to demonstrate unpatentability. See Dynamic Drinkware, 800 F.3d at 1378. We find, based on the record, that Petitioner has proved by a preponderance of the evidence that a person of ordinary skill in the art would have had reason to combine the teachings of Peterka, Suzuki, and Bocharov as proffered by Petitioner with a reasonable expectation of success.” slip op. at 45

  • ScopeMotion to amend, deniedDenied

    “We agree with Petitioner that the substitute claims are broadening. Because the amended wording only requires the key request to be made “in response to detecting” the boundary, rather than “ahead of” the boundary, the request can occur before or after the boundary. This is not a fanciful or unlikely possibility — such delayed requests are specifically contemplated by the ’178 patent: [I]f the packager 104 is unable to obtain a new content encryption key from the WFM 102 prior to the expiration of the current content encryption key, the packager 104 will continue to use the current content encryption key until such time as it is able to obtain a new key from the WFM 102. Ex. 1001, 6:32–37. It should be noted that the fixed period duration for key rotation may be viewed as a "target" period, as the packager 104 may not expire a key on the exact boundary. Ex. 1001, 8:9–11. The key expiration time from the WFM 102 may be viewed as a "suggested" expiration time, as the packager 104 may not be able to expire the key at the exact specified time.” slip op. at 56

  Patent outcomesUS 9,313,178 unpatentable
  § 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,313,178
• Google LLC / Lenovo (United States) Inc. v. Ericsson ABAll claims unpatentable
  PTAB · Mar 23, 2026 · IPR2025-00004 · APJ Georgianna W Braden · IPR · Final written decision

  Claims 1–7, 9, 11–17, and 19 are unpatentable under §103; the revised motion to amend proposing substitute claims 21–36 is denied.

  RulingsFinal written decision

  • PTAB / AIA Trials › Motions to amend / substitute claimsMotion to amend, deniedDenied

    “Board first must determine whether the motion to amend meets the statutory and regulatory requirements set forth in 35 U.S.C. § 316(d) and 37 C.F.R. § 42.121.” Lectrosonics, Paper 15 at 4 (PTAB Feb. 25, 2019) (precedential). Accordingly, a patent owner must provide a claim listing reproducing each proposed substitute claim, and must make an initial showing to demonstrate the following: (1) the amendment proposes a reasonable number of substitute claims; (2) the proposed claims are supported in the original disclosure (and any earlier filed disclosure for which the benefit of the earlier filing date is sought); (3) the amendment responds to a ground of unpatentability involved in the trial; and (4) the amendment does not seek to enlarge the scope of the claims of the patent or introduce new subject matter. See 35 U.S.C. § 326(d); 37 C.F.R. § 42.121.” slip op. at 60

  • Expert testimonyOther

    “Accordingly, we agree with Petitioner’s contentions regarding the” slip op. at 28

  • Skill levelOther

    “C. Level of Ordinary Skill in the Art In determining the level of ordinary skill in the art, various factors” slip op. at 14

  Patent outcomesUS 11,122,313 unpatentable
  Nonecites Phillips · KSR · Graham
  Patents in suitUS 11,122,313
• Magic Leap, Inc. v. Percept Technologies Inc.All claims unpatentable
  PTAB · Mar 11, 2026 · IPR2023-00495 · APJ Kristen L Droesch · IPR · Remand

  Claims 1–3 and 12–14 are unpatentable as obvious over Osterhout and, separately, over Mann ’526 and Vaissie.

  RulingsRemand decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “March 15, 2013 filing date, a person of ordinary skill in the art (“POSITA”) would have had a B.S. degree and a Masters degree in Computer Science, Computer Engineering, Electrical Engineering, Physics, or an equivalent field, as well as one to two years of academic or industry experience in wearable electronic devices or comparable industry experience. Pet. 8–9 (citing Ex. 1003 ¶ 21). Although the level of skill in the art was addressed in the Preliminary Response and the Decision on Institution (see Prelim. Resp. 27–30; Dec. on Inst. 6–10), Patent Owner does not address Petitioner’s definition of the level of ordinary skill in the art. See PO Resp. We adopt Petitioner’s definition of a person of ordinary skill in the art because it is consistent with the level of skill reflected by the ’113 Patent Specification and the asserted prior art.” slip op. at 7

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for petitioner

    “For all of the foregoing reasons, we decline to adopt Patent Owner’s proposed ordinary and customary meaning for “a dynamic eye tracking mechanism in communication with the lens” because it is not supported by the claim language or the ’113 Patent Specification, and is supported only by unsworn attorney argument.” slip op. at 13

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable

    “below, we agree with Petitioner. We find that Osterhout teaches the dynamic eye tracking mechanism is in optical communication with the lens, consistent with its ordinary and customary meaning, because in Osterhout the user’s eye receives optical communication in the form of light transmitted from the translucent lens, and the camera of the dynamic tracking mechanism, in turn, receives optical communication in the form of light from the user’s eye. See Ex. 1005 ¶¶ 164, 304.” slip op. at 20

  Patent outcomesUS 8,696,113 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 8,696,113
• Apple Inc. v. Resonant Systems, Inc.All claims unpatentable
  PTAB · Oct 23, 2025 · IPR2024-00983 · APJ Norman H Beamer · IPR · Final written decision

  Claims 1–6, 10, 17, 19, and 20 are unpatentable under § 103 over Alexander and Cosper; the alternative Gregorio-based grounds did not establish unpatentability.

  RulingsFinal written decision

  • Claim Construction › Functional claiming / §112(f) means-plus-function › Whether §112(f) applies (Williamson, nonce words)§112(f) appliesDecided for patent owner

    “112(f). Williamson v. Citrix Online, LLC, 792 F.3d 1339, 1348 (Fed. Cir. 2015). But if the term does not use the word “means,” then it is presumed not to be subject to Section 112(f). Id. “That presumption can be overcome, but only if the challenger demonstrates that the claim term fails to recite sufficiently definite structure or else recites function without reciting sufficient structure for performing that function.” Samsung Elecs. Am., Inc. v. Prisua Eng’g Corp., 948 F.3d 1342 (Fed. Cir. 2020). “The correct inquiry, when ‘means’ is absent from a limitation, is whether the limitation, read in light of the remaining claim language, specification, prosecution history, and relevant extrinsic evidence, has sufficiently definite structure to a person of ordinary skill in the art.” Apple Inc. v. Motorola, Inc., 757 F.3d 1286, 1298 (Fed. Cir. 2014).” slip op. at 12

  • Prior constructionPrior construction adoptedDecided for patent owner

    “both parties have asserted in the Apple Litigation that the “control component” requirement is a means-plus-function limitation subject to 35 U.S.C. §112(f), despite the fact that the control component limitation does not recite “means for.” Pet. 3 (citing Ex. 1012, 3–8; Ex. 1013, 13); PO Resp. 6–7. Indeed, the court in the Apple Litigation has concluded that the control component requirement is subject to 35 U.S.C. § 112(f), and has construed that requirement accordingly: Function: receiving control signals input to the oscillating resonant module; receiving outputs from the one or more sensors; controlling oscillation of the mass to produce a vibration response according to the received control signals by generating, using one or more of the received sensor outputs, control outputs to an actuator that drives the mass to oscillate. Structure: a microcontroller, a processor, a microprocessor, or a CPU that performs the algorithm shown in Figure 45 or the algorithm described in the corresponding text. See, e.g., 31:19–32:13, and equivalents thereof. Ex. 2001, 10; Ex. 2002, 40. Because of the Apple Litigation record, Petitioner presents its challenges in the alternative, first applying a plain meaning approach to the control component requirement, and also analyzing the requirement under the construction adopted in the Apple Litigation. Pet. 3–5. We adopt the court’s construction in the Apple Litigation. 35 U.S.C.” slip op. at 11

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner’s expert declarant contends that person of ordinary skill in the art (POSITA) “would have had a degree in mechanical engineering, electrical engineering, physics, or a related technical field, and at least 2–3 years of experience related to the design or development of vibration-generating systems; additional years of experience could substitute for the advanced-level degree.” Ex. 1003 ¶ 27. Patent Owner offers “a similar level of ordinary skill in the art.” PO Resp. 2. Based on a review of the record, we adopt Petitioner’s proposed level of ordinary skill in the art because it is consistent with the evidence of record, including the asserted prior art and ’882 patent specification.” slip op. at 9

  • Obviousness (§103) › Analogous artAnalogous artDecided for petitioner

    “(1) Analogous Art Our reviewing court has stated that “[t]wo separate tests define the scope of analogous prior art: (1) whether the art is from the same field of endeavor, regardless of the problem addressed and, (2) if the reference is not within the field of the inventor's endeavor, whether the reference still is reasonably pertinent to the particular problem with which the inventor is involved.” In re Bigio, 381 F.3d 1320, 1325 (Fed. Cir. 2004) (citations and internal quotes omitted). While these two criteria are helpful in many instances, we must not lose sight of the key question at hand: what is “prior art” as that term is used in 35 U.S.C. § 103(a)? References that are “too remote to be treated as ‘prior art’” are excluded from the obviousness analysis. In re Sovish, 769 F.2d 738, 741, 226 (Fed. Cir. 1985). The non-analogous art test provides helpful insight on the underlying question of what is “prior art” within the meaning of the statute; we should not, however, be blind to the reality of the circumstances of the case before us. In re Wood, 599 F.2d 1032, 1036 (CCPA (1979). Nor should we adhere to rigid and mandatory formulas that overly limit the inquiry. KSR Int’l Co., 550 U.S. at 419.” slip op. at 22

  Patent outcomesUS 11,152,882 unpatentable
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,152,882
• Apple Inc. v. Resonant Systems Inc., D/B/A/ RevelhmiAll claims unpatentable
  PTAB · Oct 9, 2025 · IPR2024-00698 · APJ Brian D Range · IPR · Final written decision

  Claims 1–5 are unpatentable as obvious under § 103 based on the asserted combinations of Izumi, Cosper, Rossi, Ibuki, and Aldrich.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art (POSITA) would have had a degree in mechanical engineering, electrical engineering, physics, or a related technical field, and at least 2–3 years of experience related to the design or development of systems incorporating linear actuators; additional years of experience could substitute for the degree. Pet. 4 (citing Ex. 1003 ¶ 30–31). Patent Owner contends a POSITA would have had (1) a bachelor’s degree in electrical engineering, mechanical engineering, or a comparable field of study, and (2) at least two years of professional experience with electro-mechanical control systems, or other similarly relevant industry experience. PO Resp. 2–3. Additional relevant industry experience may compensate for lack of formal education or vice versa. Id. Patent Owner further contends this is similar to Petitioner’s POSITA contention. Id. at 3. For purposes of this Decision, we adopt Petitioner’s proposal as reasonable and consistent with the ’767 patent specification and the prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art). Our reasoning herein would be the same under Patent Owner’s similar proposal.” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Preamble limiting or notPreamble limitingDecided for petitioner

    “Claim 1, Preamble. Both parties agree that the preamble of claim 1 is limiting. PO Resp. 6. We agree that claim 1’s preamble is limiting. We also note that the parties agreed that this preamble is limiting in the District Court case. Dist. Ct. Const. 10.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for petitioner

    “Because neither party asserts that construction of “driving component” or “control component” is necessary to resolve the issues before us, we decline to expressly construe these claim terms. See, e.g., Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). For clarity, because Petitioner argues that plain and ordinary meaning is appropriate and because Patent Owner does not dispute that construction, we adopt the plain and ordinary meaning of these claim terms when comparing the challenged claims to the prior art. Other claim terms. It is unnecessary for us to expressly construe other claim terms for purposes of this Decision. See, e.g., Realtime Data, LLC, 912 F.3d at 1375.” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundDecided for petitioner

    “Petitioner argues that a person having ordinary skill in the art would have combined Izumi’s module to include multiple sensors in accordance with Cosper’s teachings. Pet. 15. Petitioner argues that the sensors would monitor the moving element and generate a control signal in accordance with Izumi. Id. at 15–16. Petitioner further argues that Izumi’s controller would have been implemented using a microprocessor and memory as Cosper suggests. Id. at 16. Petitioner argues three reasons why a person having ordinary skill in the art would have combined Izumi with Cosper’s teachings. Id. at 16–19. First, Petitioner argues that a person having ordinary skill in the art would have looked to Cosper as a way to further Izumi’s objective of having a sensor that detects the and controls the movement of the moving element. Id. at 16–17. Second, Petitioner argues that the combination of Izumi and Cosper would have enhanced reliability of the feedback sensors by capturing “data specific to different operating parameters.” Id. at 17–18. Third, combining the references’ teachings would “facilitat[e] implementation of software instructions” by using a microprocessor and memory. Id. at 18–19. Patent Owner does not dispute Petitioner’s rationale to combine the references’ teachings. Based on our review and consideration of the record, we determine that a preponderance of the evidence supports that a person of ordinary skill in the art would have combined the teachings of Izumi and Cosper in the manner Petitioner argues (“the Izumi-Cosper combination”).” slip op. at 17

  Patent outcomesUS 8,093,767 unpatentable
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 8,093,767
• Apple Inc. v. Resonant Systems Inc., D/B/A/ RevelhmiAll claims unpatentable
  PTAB · Oct 9, 2025 · IPR2024-00697 · APJ Brian D Range · IPR · Final written decision

  Claims 1–5 are unpatentable under § 103 based on the combinations of prior art listed in the decision.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “physics, or a related technical field, and at least 2–3 years of experience related to the design or development of systems incorporating linear actuators; additional years of experience could substitute for the degree. Pet. 4 (citing Ex. 1003 ¶ 30–31). Patent Owner contends a POSITA would have had (1) a bachelor’s degree in electrical engineering, mechanical engineering, or a comparable field of study, and (2) at least two years of professional experience with electro-mechanical control systems, or other similarly relevant industry experience. PO Resp. 2–3. Additional relevant industry experience may compensate for lack of formal education or vice versa. Id. Patent Owner further contends this is similar to Petitioner’s POSITA contention and states that “Patent Owner does not believe that any of the arguments herein would change if the Board were to adopt Petitioner’s definition for the level of ordinary skill rather than Patent Owner’s.” Id. at 3. For purposes of this Decision, we adopt Petitioner’s proposal as reasonable and consistent with the ’767 patent specification and the prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art). Our reasoning herein would be the same under Patent Owner’s similar proposal.” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Preamble limiting or notPreamble limitingDecided for petitioner

    “Claim 1, Preamble. Both parties agree that the preamble of claim 1 is limiting. Pet. 6; PO Resp. 6. We agree that claim 1’s preamble is limiting. We also note that the parties agreed that this preamble is limiting in the District Court case. Dist. Ct. Const. 10.” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for petitioner

    “Because neither party asserts that construction of “driving component” or “control component” is necessary to resolve the issues before us, we decline to expressly construe these claim terms. See, e.g., Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). For clarity, because Petitioner argues that plain and ordinary meaning is appropriate and because Patent Owner does not dispute that construction, we adopt the plain and ordinary meaning of these claim terms when comparing the challenged claims to the prior art. Other claim terms. It is unnecessary for us to expressly construe other claim terms for purposes of this Decision. See, e.g., Realtime Data, LLC, 912 F.3d at 1375.” slip op. at 10

  • Obviousness (§103) › Analogous artAnalogous artDecided for petitioner

    “Our reviewing court has stated that “[t]wo separate tests define the scope of analogous prior art: (1) whether the art is from the same field of endeavor, regardless of the problem addressed and, (2) if the reference is not within the field of the inventor's endeavor, whether the reference still is reasonably pertinent to the particular problem with which the inventor is involved.” In re Bigio, 381 F.3d 1320, 1325 (Fed. Cir. 2004) (citations and internal quotes omitted). While these two criteria are helpful in many instances, we must not lose sight of the key question at hand: what is “prior art” as that term is used in 35 U.S.C. § 103(a)? References that are “too remote to be treated as ‘prior art’” are excluded from the obviousness analysis. In re Sovish, 769 F.2d 738, 741, 226 (Fed. Cir. 1985). The non-analogous art test provides helpful insight on the underlying question of what is “prior art” within the meaning of the statute; we should not, however, be blind to the reality of the circumstances of the case before us. In re Wood, 599 F.2d 1032, 1036 (CCPA (1979). Nor should we adhere to rigid and mandatory formulas that overly limit the inquiry. KSR Int’l Co. v. Teleflex Inc., 550 U.S. 398, 419 (2007).” slip op. at 20

  Patent outcomesUS 8,093,767 unpatentable
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 8,093,767

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.