• Apple Inc. v. RJ Technology LLCSome claims unpatentable
  PTAB · Feb 18, 2025 · IPR2023-01350 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 5–10 are unpatentable as obvious; claims 11–14 were not shown unpatentable because the evidence did not establish the claimed capacity retention after 400 cycles.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends a person of ordinary skill in the art “would have held a Bachelor’s degree in chemistry or chemical engineering, with at least 4 years of experience in cell design, electrochemical techniques, and battery materials development.” Pet. 4. Petitioner further contends that a “Master’s Degree can substitute[] for some of the relevant experience,” and “[e]quivalent training with battery specific experience can accommodate other degreed fields.” Id. 9 The parties here do not address objective evidence of nonobviousness. Patent Owner does not dispute Petitioner’s definition of the ordinarily skilled artisan. PO Resp. 20. We adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the ’641 patent, the prior art of record, and the parties’ arguments.” slip op. at 6

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “The parties agree that the term “charge cut-off voltage” is “the maximum voltage to which the battery is configured to be charged.” PO Resp 21–22; Pet. Reply 1. The parties dispute, however, whether the “charge cut-off voltage” is a “battery property” or “the voltage applied to the battery during charging.” PO Resp. 21–24; Pet. Reply 1–6. We need not resolve the precise meaning of “charge cut-off voltage” because there is no dispute that Yamaki discloses this limitation under either party’s interpretation of the claim term. Upon review of the prior art and the parties’ arguments, we determine that no terms of the ’641 patent require express construction. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))); Pet. Reply 1 (asserting that the challenged claims are unpatentable under either parties’ construction of “charge cut-off voltage”).” slip op. at 7

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “Patent Owner’s arguments do not persuasively undermine Petitioner’s position. Sakamoto expressly discloses setting the ratio of negative to positive electrode active material in the range of 1.05 to 1.30. Ex. 1005 ¶ 8. Sakamoto also explains why this range is preferable, i.e., if the ratio is roughly equal “the charge-discharge cycle performance is insufficient due to significant deterioration from charging and discharging,” and if the ratio is 10 Citations to the prosecution history of Yamaki are to the page numbers added to the lower right corner of the document. too high “too much of the compound does not participate in charging and discharging.” Id. ¶¶ 6, 8. These disclosures are sufficient to explain why one of ordinary skill in the art would have found it obvious to select the ratios disclosed in Sakamoto in Yamaki. Id. ¶ 8 (providing a secondary battery with a capacity ratio between 1.05 and 1.30 and noting that by setting the ratio within this range the resulting secondary lithium battery is “safe due to low risk of heat being generated and an explosion occurring”). We also disagree that Sakamoto teaches away from elevated voltages or from increasing the amount of lithium in circulation. See PO Resp. 29. Contrary to Patent Owner’s arguments, Sakamoto provides no general teaching against using a charge cut-off voltage above 4.2 V, or against increasing the level of lithium in circulation. Nor does Sakamoto “criticize, discredit, or otherwise discourage” the claimed invention. In re Fulton, 391 F.3d 1195, 1201 (Fed. Cir. 2004). Rather, Sakamoto warns against setting the reversible capacities of the positive and negative electrode substantially equal as this may result in excess lithium plating on the surface of the electrode. Ex. 1005 ¶¶ 6, 8. We agree with Petitioner that this disclosure would lead one of ordinary skill in the art to design a battery with a higher capacity in the negative electrode active material than the positive electrode active material. Pet. 11–12.” slip op. at 14

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner

    “We also disagree that Sakamoto teaches away from elevated voltages or from increasing the amount of lithium in circulation. See PO Resp. 29. Contrary to Patent Owner’s arguments, Sakamoto provides no general teaching against using a charge cut-off voltage above 4.2 V, or against increasing the level of lithium in circulation. Nor does Sakamoto “criticize, discredit, or otherwise discourage” the claimed invention. In re Fulton, 391 F.3d 1195, 1201 (Fed. Cir. 2004). Rather, Sakamoto warns against setting the reversible capacities of the positive and negative electrode substantially equal as this may result in excess lithium plating on the surface of the electrode. Ex. 1005 ¶¶ 6, 8. We agree with Petitioner that this disclosure would lead one of ordinary skill in the art to design a battery with a higher capacity in the negative electrode active material than the positive electrode active material. Pet. 11–12.” slip op. at 15

  Patent outcomesUS 7,749,641 mixed
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 7,749,641
• Samsung Electronics Co., Ltd. / Apple Inc. v. RJ Technology LLCSome claims unpatentable
  PTAB · Jan 17, 2025 · IPR2024-00597 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 2–4 and 6–18 are unpatentable as obvious over Abe and Guyomard, with claims 9–10 also obvious over Iwaizono; claims 1 and 5 were not shown unpatentable.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art “would have had a Master’s degree in material science, chemical engineering, chemistry, or similar field with four years of experience designing testing, and building secondary lithium batteries.” Pet. 11 (citing Ex. 1002 ¶ 51). Petitioner further contends that a person of ordinary skill in the art would have been aware of “(1) positive electrode materials, (2) negative electrode materials, (3) separators, (4) electrolytes, (5) charge-discharge parameters, and (6) protection circuits, as well as ‘battery failure modes’ such as plating and the formation of dendrites.” Id. (citing Ex. 1002 ¶¶ 50–51). Patent Owner “does not dispute Petitioner’s level of ordinary skill.” PO Resp. 17. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the disclosures of the ’641 patent and the prior art of record.” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “We also agree with Patent Owner that the charge cut-off voltage is not necessarily the applied voltage during charging. PO Resp. 20. Rather, depending on the charging protocol used and when in the charging cycle the voltage is applied, the applied voltage could be higher than the battery voltage. Ex. 2013; Ex. 2006 ¶ 91. For example, as discussed in more detail below with respect to the Uemura grounds, when fast charging using constant current is used and the charging rate is not slow, the applied voltage will be higher than the battery voltage when the constant current charging phase is stopped. Ex. 2006 ¶ 91; Ex. 2013. Likewise, during constant current/constant voltage charging, the applied voltage approximates the battery voltage only when the battery is nearly completely charged. Ex. 2013; Ex. 2006 ¶ 91. Thus, the applied voltage may be, but is not necessarily, the charge cut-off voltage. In view of the foregoing, we construe “charge cut-off voltage” in claims 1 and 5 as “the maximum value to which the battery is configured to be charged.” PO Resp. 18; Ex. 2008, 217:6–11; Pet. Reply 5. Contrary to Patent Owner’s arguments, however, we do not understand the phrase “configured to be charged” to necessarily represent a single voltage for the battery that is determined based on the structure and chemistry of the battery. Pet. Reply 4–5. Rather, the charge cut-off voltage is a selected potential, or voltage, of the battery or cell at the end of charging that is controlled by a circuit or device, such as a charger or control circuit within the battery. Ex. 1001, 9:50–55; Ex. 1048, 2, 7–8; Ex. 1008, 3:9–13. And, for the reasons discussed herein, the charge cut-off voltage may be, but is not necessarily, the same as the applied voltage during charging. PO Resp. 20.” slip op. at 15

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “charge cut-off voltage “greater than 4.2 V but less than 5.8 V” and calculating a specific or theoretic capacity “with a charge cut-off voltage limited to 4.2” (claim 1) or “with a charge cut-off voltage set at 4.2 V” (claim 5). Ex. 1001, 16:56–61, 17:6–11. Although the parties dispute the precise scope of these claim terms, the parties agree that the first use of “charge cut-off voltage” in claims 1 and 5 refers to the potential of the battery as a whole (between the cathode and the anode), and not a half-cell voltage using lithium metal as a counter electrode.10 Tr. 17:1–3 (agreeing 10 With respect to the phrase “as calculated by a theoretic capacity with a charge cut-off voltage set at 4.2 V,” the parties in fact appear to be in that the first use of “charge cut-off voltage” in claim 5 refers to a full-cell voltage); Sur-reply 5; PO Resp. 22. We need not further construe the claims to resolve the disputes between the parties. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 16

  • Expert testimonyPatent owner expert creditedDecided for patent owner

    “Given Mr. Juzkow’s unambiguous testimony that Uemura uses constant current charging that would stop when the applied voltage reached 11 The chart is reproduced from SAFT, Charging your lithium-ion batteries: 5 expert tips for a longer lifespan, (https://www.saft.com/energizing-iot/charging-your-lithium-ion-batteries-5-expert-tips-longerlifespan#:~: text=When%20the%20battery%20provides%20current,This%20restore s%20the%20battery's%20capacity). 4.3 V, as well as Dr. Yao’s persuasive testimony that Uemura’s constant charging rate is not slow, we credit the testimony of Dr. Yao that one of ordinary skill in the art would have understood that the internal voltage to which the battery of Uemura was charged is less than 4.3 V. Ex. 2006 ¶ 119. In particular, Dr. Yao persuasively testifies that one of ordinary skill in the art would have believed that the charge cut-off voltage was no more than 4.2 V, and most likely equal to “about 4 V.” Id. ¶¶ 119–122.” slip op. at 21

  Patent outcomesUS 7,749,641 mixed
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 7,749,641
• Samsung Electronics Co., Ltd. / Apple Inc. v. RJ Technology LLCSome claims unpatentable
  PTAB · Jan 17, 2025 · IPR2023-01183 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 2–4 and 6–18 are unpatentable as obvious over Abe and Guyomard, with claims 9 and 10 also obvious over Iwaizono; claims 1 and 5 were not shown unpatentable.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art “would have had a Master’s degree in material science, chemical engineering, chemistry, or similar field with four years of experience designing testing, and building secondary lithium batteries.” Pet. 11 (citing Ex. 1002 ¶ 51). Petitioner further contends that a person of ordinary skill in the art would have been aware of “(1) positive electrode materials, (2) negative electrode materials, (3) separators, (4) electrolytes, (5) charge-discharge parameters, and (6) protection circuits, as well as ‘battery failure modes’ such as plating and the formation of dendrites.” Id. (citing Ex. 1002 ¶¶ 50–51). Patent Owner “does not dispute Petitioner’s level of ordinary skill.” PO Resp. 17. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the disclosures of the ’641 patent and the prior art of record.” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “constructions. First, we agree with Petitioner that the ’641 patent indicates that the charge cut-off voltage selected for a particular battery need not be a fixed property of the battery or something that is set by the design and chemistry of the battery. Consistent with this conclusion, the ’641 patent discloses that a “charging device controls the charge cut-off voltage of the single lithium-ion cell within a range from 4.3 V to 5.8 V.” Ex. 1001, 9:50– 55. This strongly suggests that the charge cut-off voltage is controlled by the charger and is not necessarily an inherent property of the battery. Patent Owner contends that this is merely an unclaimed embodiment, but the relevant disclosure states that the charging device for the “present invention” may be any type of device “with the proviso that said charging device controls the charge cut-off voltage.” Id. at 9:50–53.” slip op. at 12

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “charge cut-off voltage “greater than 4.2 V but less than 5.8 V” and calculating a specific or theoretic capacity “with a charge cut-off voltage limited to 4.2” (claim 1) or “with a charge cut-off voltage set at 4.2 V” (claim 5). Ex. 1001, 16:56–61, 17:6–11. Although the parties dispute the precise scope of these claim terms, the parties agree that the first use of “charge cut-off voltage” in claims 1 and 5 refers to the potential of the battery as a whole (between the cathode and the anode), and not a half-cell voltage using lithium metal as a counter electrode.10 Tr. 17:1–3 (agreeing 10 With respect to the phrase “as calculated by a theoretic capacity with a charge cut-off voltage set at 4.2 V,” the parties in fact appear to be in that the first use of “charge cut-off voltage” in claim 5 refers to a full-cell voltage); Sur-reply 5; PO Resp. 22. We need not further construe the claims to resolve the disputes between the parties. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 16

  • Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner

    “Given Mr. Juzkow’s unambiguous testimony that Uemura uses constant current charging that would stop when the applied voltage reached 11 The chart is reproduced from SAFT, Charging your lithium-ion batteries: 5 expert tips for a longer lifespan, (https://www.saft.com/energizing-iot/charging-your-lithium-ion-batteries-5-expert-tips-longerlifespan#:~: text=When%20the%20battery%20provides%20current,This%20restore s%20the%20battery's%20capacity). 4.3 V, as well as Dr. Yao’s persuasive testimony that Uemura’s constant charging rate is not slow, we credit the testimony of Dr. Yao that one of ordinary skill in the art would have understood that the internal voltage to which the battery of Uemura was charged is less than 4.3 V. Ex. 2006 ¶ 119. In particular, Dr. Yao persuasively testifies that one of ordinary skill in the art would have believed that the charge cut-off voltage was no more than 4.2 V, and most likely equal to “about 4 V.” Id. ¶¶ 119–122. Petitioner argues that because the battery of Uemura is charged “to” a maximum voltage of 4.3 V, Uemura discloses the claimed charge cut-off voltage under either Petitioner’s or Patent Owner’s construction of the term. Pet. Reply 11–12 (citing Ex. 1009 ¶ 81; Ex. 1044 ¶¶ 56–59). This argument is not persuasive because Mr. Juzkow unambiguously testified that charging in Uemura stopped when the applied voltage reached 4.3 V, and Uemura discloses that the battery was charged “at” a voltage ranging from 4.3 V to 2.0 V, not “to” such a voltage. Ex. 1009 ¶ 81; Ex. 2008, 113:2–13; Ex. 2006 ¶ 119 n.64; Sur-reply 9. In view of the foregoing, we determine that Petitioner has not demonstrated by a preponderance of the evidence that Uemura anticipates independent claims 1 and 5 of the ’641 patent.” slip op. at 21

  Patent outcomesUS 7,749,641 mixed
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 7,749,641
• Fusion Orthopedics, LLC v. Extremity Medical, LLCSome claims unpatentable
  PTAB · Nov 4, 2024 · IPR2023-00894 · APJ Robert A Pollock · IPR · Final written decision

  Claims 1–10 and 12–15 are unpatentable; claim 11 was not shown unpatentable. Substitute claims 16–25 and 27–30 are unpatentable over Mazur; claim 26 was not reached.

  RulingsFinal written decision

  • BurdenMixed

    “It is of the utmost importance that petitioners in the IPR proceedings adhere to the requirement that the initial petition identify ‘with particularity’ the ‘evidence that supports the grounds for the challenge to each claim.’” Intelligent Bio-Sys., Inc. v. Illumina Cambridge Ltd., 821 F.3d 1359, 1369 (Fed. Cir. 2016) (quoting 35 U.S.C. § 312(a)(3)). Here, however, not until its Reply does Petitioner belatedly suggest that Ferrante’s disclosure of bone screws with self-tapping ends equally meets the limitation of claim 10 (with respect to the first member) as with claim 11 (with respect to the second member), and that both claims are obvious in light of “evidence” from Ferrante “that it was well known to equip bone screws with self-tapping ends.” Reply 26–27. We do not discern these arguments in the Petition, and consider them waived. See Netflix, Inc. v. DivX, LLC, 84 F.4th 1371,1377 (Fed. Cir. 2023) (“While the Board should not take an overly mechanistic view of a petition and decline to address an argument because the petitioner did not present it with ideal vigor and clarity, the Board should also not have to decode a petition to locate additional arguments beyond the ones clearly made.”). In sum, Petitioner’s error in failing to first address limitations of claim 10 in the Petition specific to the Cognet/Ferrante combination indicates a failure to meet the particularity requirements for what must be in the petition and cannot be left to be filled in on reply. See 35 U.S.C. § 312(a)(3); 37 C.F.R. §§ 42.22(a)(2) (requiring, among other things, “a detailed explanation of the significance of the evidence”), 42.104(b)(4)–(5) (requiring that petition “specify where each element of the claim is found in the prior art patents or printed publication relied upon” and, regarding submitted evidence, state “the relevance of the evidence to the challenge raised, including identifying specific portions of the evidence that support the challenge”). Microsoft, 2022 WL 989403, at *6. Accordingly, Petitioner has not shown persuasively that claim 11 would have been obvious in light of Cognet and Ferrante for the reasons set forth in the Petition. slip op. at 41

  • Expert testimonyPetitioner expert creditedDecided for petitioner

    “We also find persuasive Mr. Dominguez’s explanation that one of ordinary skill in the art would have understood “bore” as including stepped diameter holes, sometimes described as a bore having a counterbore. See generally Ex. 1018 ¶¶ 4–29; Reply 3–10. Three of Mr. Dominguez’s illustrative examples are reproduced in the annotated figures below. The above figures show Mr. Dominguez’s annotated illustrations from the Jackson (Ex. 1019, Fig. 3), Brånemark (Ex. 1021, Fig. 4), and Ray (Ex. 1025, Fig. 1) references as discussed at paragraphs 10, 12, and 13, respectively, of Mr. Dominguez’s Second Declaration. With reference to the above figures, Mr. Dominguez testifies that “Jackson describes a bone repair set screw in which ‘[t]he bore 27 comprises a first bore section 31, a second bore section 32,’ etc. delineated by shoulders 41, 42, etc. (Ex. 1019, 5:24– 43)” (Ex. 1018 ¶ 10); “Brånemark describes an osseous implantation device having body 1ʺ with first and second holding portions 21ʺ, 31ʺ and ‘an inner through bore with a first portion 4ʺ in the first holding portion and a second portion 5ʺ in the second holding portion.’” Ex. 1021, 4:44–46” (id. ¶ 12); and Ray discloses surgical calipers including “handle 12 having ‘stepped cylindrical bore 14,’” wherein “[c]ollar 20 of a shaft inserted in the bore ‘rests against a step of the bore 14’ (2:14–15)” (id. ¶ 13). Patent Owner responds that Mr. Dominguez’s examples “that allegedly show a single bore encompassing two or more stepped-diameter holes or a counterbore . . . . are specific to these references and divorced from the disclosures of the ’166 patent.” Sur-Reply 7. Insofar as the ’166 patent makes no mention of the term “bore” outside the claims, and Mr. Dominguez’s examples are all taken from the field of orthopedic surgery, we do not find this argument persuasive. Patent Owner further appears to contend that exemplary references to a “cylindrical stepped down bore” or a “stepped cylindrical bore” are too specific to be within the scope of the term “bore.” Sur-Reply 7–8. As these terms merely describe species within a larger genus, and Patent Owner presents no cogent reason to exclude them, we do not find this argument availing. Relatedly, we are also not persuaded by Patent Owner’s argument that “the prior art treats a ‘bore’ as an element that is distinct from a ‘counterbore.’” Id. at 8. Rather, we credit Mr. Dominguez’s testimony that “[a] counterbore is not a structure unto itself, a counterbore is part of a larger structure” as exemplified by numerous examples including Laps (Ex. 1028 ¶ 33 (sensor assembly wherein “bore 16 includes a counterbore 18”)); Martinez (Ex. 1029, 3:61 (surgical cutting instrument wherein “bore 56 has a counterbore 64”)); Zang (Ex. 1030, 2:49 (bone anchor having a “bore [that] includes a counterbore”)); Ledet (Ex. 1022, 29:3–5 (vertebral fixation plate having “through holes . . . . countersunk, or counterbored to accommodate the head of a bone screw”)); Seo (Ex. 1031, 3:45 (chair leg employing “counterbored bore 23”)); and Exner (Ex. 1032, 2:16 (extrusion press including “counterbored axial bore 6”)). Ex. 1018 ¶¶ 17–23. That a reference may refer to a figure as showing “bore 103” with “counterbore 105 . . . formed on one end” does not indicate that they are distinct structures as Patent Owner contends, but merely that the focus of each term is directed to the entire bore or to a particular aspect of the bore, i.e., its counterbore. See” slip op. at 22

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Patent Owner subsequently proposed an alternative definition, as a person having “[a] Bachelor’s Degree in biomedical and/or mechanical engineering or similar training and . . . at least three years of experience with implant devices used for internal fixation of bones.” POR 5 (citing Ex. 2012 ¶¶ 32–33). According to Patent Owner, “[t]his hypothetical person would be capable of performing various design tasks and would understand the basic mechanical features and operation of orthopaedic implant devices [and] have an appreciation for orthopaedic fusion techniques and the medical issues and concerns faced by a doctor/surgeon charged when performing operations to implant orthopaedic devices.” Id. Despite some differences in wording, Patent Owner asserts (and Petitioner does not contest) that any “distinction between the parties’ proposed definitions of a POSITA does not affect the arguments set forth herein.” Id. (citing Ex. 2012 ¶ 34). Consistent with this view, we find the parties’ constructions equally applicable in light of the prior art of record and the disclosure of the ’166 patent. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (“the prior art itself [may] reflect[] an appropriate level” as evidence of the ordinary level of skill in the art) (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163 (Fed. Cir. 1985)). We adopt, for convenience, Petitioner’s definition, but our analysis does not change depending on which of the two articulations are applied here. H.” slip op. at 12

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “one of ordinary skill in the art would understand that “bore,” as used in the context of claims 1 and 12, encompasses a multi-diameter passage, and in particular, one having stepped longitudinal cross sections such as that shown in Cognet’s Figure 1. See generally DI 11–13. For the reasons that follow, we conclude that one of ordinary skill in the art would have understood “bore” as such. Relying on the testimony of Mr. Dominguez, Petitioner initially proposed a construction of “bore” as “a usually cylindrical hole made by or as if by the turning or twisting movement of a tool.” Pet. 16 (citing Ex. 1002 ¶ 58). Petitioner’s proposal relied on Mr. Dominguez’s testimony that “[a] bore is a cylindrical hole made by the spinning rotation of a twist drill cutting tool. It is typically made by removing material from a solid or hollow object, similar to a tunnel or orifice.” Ex. 1002 ¶ 58. Pointing to its annotation of Cognet’s Figure 1, above, Patent Owner argued that that the term “bore” excludes a tunnel made by “two adjacent bores.” See Prelim. Resp. 21–25. In view of the then-available evidence, we provisionally construed “bore” as a hole or passage made by or as if by the turning or twisting movement of a tool such that its interior walls have cylindrical lateral cross-sections, and which do not exclude holes or passages having tapered or stepped longitudinal cross-sections. DI 13.” slip op. at 19

  Patent outcomesUS 11,298,166 mixed
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · Graham
  Patents in suitUS 11,298,166
• Pelican Biothermal, LLC v. Va-Q-Tec AGSome claims unpatentable
  PTAB · Jun 16, 2023 · PGR2021-00085 · APJ Barry L Grossman · PGR · Final written decision

  The Board granted the motion to amend but held amended claim 64 unpatentable as anticipated by NanoCool 98596-type products and obvious over the cited combinations; all other amended claims were not shown unpatentable.

  RulingsFinal written decision

  • PTAB / AIA Trials › Motions to amend / substitute claimsMotion to amend granted in partGranted in part

    “VI. ORDER In consideration of the foregoing, it is hereby: ORDERED that Petitioner has demonstrated by a preponderance of the evidence that amended claim 64 is unpatentable; FURTHER ORDERED that Patent Owner’s Non-Contingent Motion to Amend is granted for claims 64 and denied for all other amended claims; and” slip op. at 77

  • ExcludeMotion to exclude, deniedDenied

    “A. Status as Prior Art Is a Substantive Issue, Not an Evidentiary Issue. A motion to exclude is not an appropriate mechanism for challenging the sufficiency of evidence, such as whether a reference qualifies as prior art, or the proper weight that should be afforded an argument. See Flir Systems, Inc. v. Leak Surveys, Inc., IPR2014-00411, Paper 113, 4, 8–9 (PTAB September 3, 2015); PTAB Consol. Trial Practice Guide 79 (Nov. 30 Mr. Zumwalt testifies that other NanoCool products, designated by product number 85430 and 98630, also have the same configuration as the 98830 product and are made by the same process. Thus, “the 98830, 85430, and 98630 products can be collectively referred to as ‘98830-type’ products all having the same relevant design.” Ex. 1030 ¶ 17. 2019) (“A motion to exclude . . . may not be used to challenge the sufficiency of the evidence to prove a particular fact. A motion to exclude is not a vehicle for addressing the weight to be given evidence—arguments regarding weight should appear only in the merits documents.”); Caterpillar Inc. v. Wirtgen Am., Inc., IPR2017-02187, Paper 42,17 (PTAB May 21, 2019) (status as prior art “is a substantive issue, not an evidentiary issue.”) Thus, whether the NanoCool 98830 product is prior art is not the proper basis for Patent Owner’s Motion to Exclude evidence concerning the NanoCool 98830 product.” slip op. at 29

  • Skill levelSkill level board ownOther

    “Neither Petitioner nor Mr. Harber provide any analysis of the factors pertinent to a determination of the level of ordinary skill, identified above, to support their conclusory statements. We give Mr. Harber’s conclusory testimony minimal probative weight. 37 C.F.R. § 42.64(a) (“Expert testimony that does not disclose the underlying facts or data on which the opinion is based is entitled to little or no weight.”). Moreover, there is no persuasive evidence to which we have been directed of the need for specific education or experience in biological or chemical technologies related to the claimed containers and inserts.” slip op. at 26

  • Expert testimonyPetitioner expert discountedDecided for patent owner

    “With regard to the level of ordinary skill in the art, Petitioner asserts that a person of ordinary skill would have had “a bachelor’s degree or higher degree in biological, chemical or mechanical engineering, or related sciences, and at least two to five years of experience in designing and testing ISCs [insulated shipping containers] depending on education level.” Pet. 9 (emphasis added) (citing Ex. 1002 ¶¶ 23–24). Exhibit 1002 is the Declaration testimony of Mr. Paul Haber. Mr. Harber actually states a slightly different level of ordinary skill. Mr. Harber testifies: The hypothetical POSITA would have: (i) at least a bachelor’s degree in biological, chemical or mechanical engineering, or related sciences, and have at least three to five years of experience in designing and testing ISCs [Insulated Shipping Containers][29]. Such a person may also have (ii) a higher level degree, such as a PhD and/or Master’s degree in engineering, or related sciences, and have at least two to three years of experience in designing and testing ISCs. 29 See Ex. 1002 ¶ 23. Ex. 1002 ¶ 24 (emphasis added). Mr. Harber also testifies that “[t]hese descriptions are approximate, and a higher level of education or specific skill might make up for less experience, and vice-versa.” Id.” slip op. at 25

  Patent outcomesUS 10,766,685 mixed
  Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · KSR · Graham
  Patents in suitUS 10,766,685
• Samsung Electronics Co., Ltd. v. Lynk Labs, Inc.Some claims unpatentable
  PTAB · May 5, 2023 · IPR2022-00098 · APJ Arthur M Peslak · IPR · Final written decision

  Claims 1, 3, and 4 are unpatentable as obvious over the stated combinations; claim 2 was not shown unpatentable because the driver was not shown configured to receive the rectifier’s forward voltages.

  RulingsFinal written decision

  • Skill levelSkill level patent owner adoptedDecided for patent owner

    “We agree with Patent Owner that a person of ordinary skill in the art would have had experience in LED devices. For this reason, we apply Patent Owner’s proposed level of ordinary skill in the art because it comports with the level of skill reflected in the ’149 patent and the prior art of record. However, if we were to apply Petitioner’s proposed level of skill, our Decision would not be affected.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Upon review of the entire record, we determine that no claim terms require express construction. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (noting that “we need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy’”) (citing Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 10

  • Expert testimonyPetitioner expert creditedPatent owner expert discountedMixed

    “Dr. Ducharme’s testimony that “the spacing of the chips in Zhang would not likely be so close as to create overheating issues” (Ex. 2002 ¶ 111) is unsupported by any disclosure of the actual spacing of Zhang’s chips. Consequently, his testimony that there would be no overheating concerns in Zhang due to the spacing of the chips is entitled to little, if any, weight. Dr. Ducharme further testifies that the components of Zhang’s driver “could easily increase the temperature of the LED 19 chips on the circuit board, which can cause LEDs to generate less illumination, burn out and otherwise adversely affect their performance.” Ex. 2002 ¶ 126. Dr. Ducharme further testifies that “[i]t is well-known that excessive operational temperatures can reduce the illumination provided by the LEDs, can decrease the operational lifetime of the LEDs, and if the temperature is sufficiently high, it can cause LED junction failure and a burnt-out LED.” Id. We agree with this testimony, which as discussed below, is consistent with Salam. Dr. Ducharme’s testimony concerning overheating issues caused by the driver components contradicts Patent Owner’s ’s contention that there would not be “an overheating issue with Zhang’s LED exit sign circuit in Figure 2.1.” PO Resp. 30. Regardless of whether Zhang’s LEDs in Figure 2.1 have a heat problem or not, Salam teaches the advantages of using a heat sink. Salam teaches that a heat sink will result in a higher efficiency of the LEDs and improved life. Ex. 1006, 16:38–43. The Federal Circuit, in DyStar Textilfarben GmBH & Co v. C.H. Patrick Co., 464 F.3d 1356 (Fed. Cir. 2006), stated that “the desire to enhance commercial opportunities by improving a product or process is universal–and even common-sensical . . . the proper question is whether the ordinary artisan possesses the knowledge and skills rendering him capable of combining the prior art references.” Id. at 1368. Dr. Ducharme testified that a person of ordinary skill in the art “would have an understanding of the generation of heat and using a heat sink to remove unwanted heat from electronics and LED lighting devices.” Ex. 1102, 23:18–24:3. Dr. Ducharme’s testimony is consistent with Petitioner’s contention that the combination of Zhang and Salam “would have been a straightforward combination of known components and technologies, according to known methods, to produce the predictable result of reducing/ mitigating heat effects in a circuit.” Pet. 17 (citing Ex. 1002 ¶ 106). Patent Owner next contends it would be extremely burdensome and costly to modify Zhang to add a heat sink layer because “each of the multiple chips mounted and epoxied to Zhang’s circuit board in the exit sign would have to be modified.” PO Resp. 30 (citing Ex. 2002 ¶ 112). Dr. Ducharme’s testimony repeats the Patent Owner Response verbatim and is entitled to little, if any, weight. Ex. 2002 ¶ 112. Nonetheless, this contention is unavailing because it is based on Patent Owner’s bodily incorporation of Zhang and Salam. Patent Owner next contends that a person of ordinary skill in the art” slip op. at 27

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “Regardless of whether Zhang’s LEDs in Figure 2.1 have a heat problem or not, Salam teaches the advantages of using a heat sink. Salam teaches that a heat sink will result in a higher efficiency of the LEDs and improved life. Ex. 1006, 16:38–43. The Federal Circuit, in DyStar Textilfarben GmBH & Co v. C.H. Patrick Co., 464 F.3d 1356 (Fed. Cir. 2006), stated that “the desire to enhance commercial opportunities by improving a product or process is universal–and even common-sensical . . . the proper question is whether the ordinary artisan possesses the knowledge and skills rendering him capable of combining the prior art references.” Id. at 1368. Dr. Ducharme testified that a person of ordinary skill in the art “would have an understanding of the generation of heat and using a heat sink to remove unwanted heat from electronics and LED lighting devices.” Ex. 1102, 23:18–24:3. Dr. Ducharme’s testimony is consistent with Petitioner’s contention that the combination of Zhang and Salam “would have been a straightforward combination of known components and technologies, according to known methods, to produce the predictable result of reducing/ mitigating heat effects in a circuit.” Pet. 17 (citing Ex. 1002 ¶ 106).” slip op. at 27

  Patent outcomesUS 10,517,149 mixed
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 10,517,149
• Home Depot USA, Inc. v. Lynk Labs, Inc.Some claims unpatentable
  PTAB · May 5, 2023 · IPR2022-00023 · APJ Arthur M Peslak · IPR · Final written decision

  Claims 1 and 4 are unpatentable over the stated § 103 combinations; Petitioner did not show claim 2 unpatentable because it did not explain how the LED array’s forward voltage is received by the driver.

  RulingsFinal written decision

  • Skill levelSkill level board ownOther

    “degree in electrical engineering, or similar technical field, with two years of experience in the field of design and/or development of light-emitting diodes (LEDs) and circuits in the context of lighting control systems.” Pet. 11–12 (citing Ex. 1002 ¶ 34). Petitioner further contends that “[a]n increase in experience could compensate for less education.” Id. at 12. Patent Owner proposes the same level of skill in the art. See PO Resp. 6. We apply the parties’ undisputed level of ordinary skill in the art because it comports with the level of skill reflected in the ’149 patent and the prior art of record.” slip op. at 8

  • Expert testimonyPetitioner expert creditedDecided for petitioner

    “We credit Dr. Lebby’s testimony over Dr. Ducharme for the following reasons. First, in Deese, power cable 28 is inserted into an opening in rubber housing 21. Ex. 1008, Fig. 2A. [R]ubber housing 21 forms a water-tight seal around the power cable 28.” Id. at 4:63–65. Dr. Ducharme does not explain why Hochstein’s protruding heat sink shell could not similarly be inserted through rubber housing 21 with a water-tight seal. Further, Dr. Lebby relies on the similarity between the structures of Deese and Hochstein. Hochstein uses gasket 45 and weather seal 48 to seal housing 10 with electrical lead 49 and heat sink shell 38 extending therethrough. Ex. 1010, 5: 39–40, 5:63:65, Fig. 8.” slip op. at 47

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed patent owner constructionOther

    “Our analysis starts with the claim language. Claim 1 recites “a driver, wherein the driver includes at least one transistor and at least one capacitor” and “the driver is configured to receive an AC voltage from a mains power source and provide a voltage and current to the at least one LED circuit.” Ex. 1001, 23:16–17, 26:22–24. Dr. Ducharme testifies that power is determined by multiplying voltage and current. Ex. 2008 ¶ 63. The language of claim 1, thus, supports Patent Owner’s construction which is also consistent with the dictionary definition offered by Petitioner which also defines “driver” as [a] program, circuit or device used to power or control other programs, circuits or devices.” Ex. 1007, 4 (emphasis added). The Specification provides “the driver providing an AC voltage and current to one or more LED circuits.” Ex. 1001, 3:65–67. Thus, the Specification also provides support for Patent Owner’s construction. For the foregoing reasons, we apply Patent Owner’s proposed construction of “driver” because it is consistent with the language of claim 1 and the description of driver in the Specification. We note that the adjective “LED” prior to circuits or devices in Patent Owner’s construction is not necessary because that it essentially repeats limitation 1.e.” slip op. at 12

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITADecided for petitioner

    “We begin with the claim language itself which is “the package is a heat sinking reflective material.” Ex. 1001, 23:18–19 (emphasis added). In its analysis, Patent Owner parses “heat sinking reflective material” out of context by omitting the italicized language “the package is” preceding “heat sinking reflective material.” PO Resp. 29. The deposition testimony of Dr. Lebby and Dr. Ducharme’s declaration testimony cited by Patent Owner are also out of context. The Specification of the ’149 patent defines “package” as an integrated unit that “in certain applications may preferably include a heat sink, a reflective material, a lens for directing light, phosphor nano-crystals or light changing or enhancing substances.” Ex. 1001, 5:30–33. Because heat sink and reflective material are listed separately in the Specification, this disclosure suggests that, at least in certain embodiments, a package with a heat sink separate from a reflective material would fall within the scope of limitation 1.c. This is further confirmed by comparing the packages illustrated in Figures 25 and 26 of the ’149 patent which are reproduced above. Figure 25 is described as illustrating “heat sinking material 198 . . . integrated into the package 30.” Id. at 17:34–35. Figure 26 is described as illustrating reflector 202 “integrated into the package 30 for optimized light dispersion.” Id. at 17:47–49. As can be seen from a visual comparison of Figures 25 and 26, reflector 202 is separate from heat sinking material 198. Given the disclosure in the ’149 patent of a package with a heat sink” slip op. at 15

  Patent outcomesUS 10,517,149 mixed
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,517,149
• Samsung Electronics Co., Ltd. v. Lynk Labs, Inc.Some claims unpatentable
  PTAB · Apr 19, 2023 · IPR2021-01576 · APJ Scott Raevsky · IPR · Final written decision

  Claims 1–12 are unpatentable as obvious; claims 13–18 are not shown unpatentable because the asserted combinations fail to teach or suggest multiple LED packages connected in series.

  RulingsFinal written decision

  • Skill levelSkill level patent owner adoptedDecided for patent owner

    “PO Resp. 8 (citing Ex. 2001 ¶¶ 41–42). Patent Owner argues that its definition is superior because Petitioner’s “and/or” qualifier “might be read as considering a person who has ‘related circuit design’ experience but no experience with ‘LED devices’ to be a POSITA.” Id. at 9. Patent Owner further views Petitioner’s “or a related field” phrasing as potentially including a person who has no experience with LED devices. Id. We agree with Patent Owner on both points. We agree with Patent Owner that Patent Owner’s proposal is more consistent with the problems and solutions in the ’979 patent and prior art of record. We adopt Patent Owner’s definition of the level of skill but note that had we adopted Petitioner’s level of skill, we would not have reached a different outcome here.” slip op. at 6

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “specification support its construction of “formed or mounted to” as encompassing indirect attachment to the substrate. Neither the plain claim language nor the specification requires the phosphor coating to be directly attached to the substrate. Limitation 1(c) recites, wherein the LED chips comprise a phosphor coating to produce a change in a color or a quality of light emitted from the LED chips, wherein the LED chips, the power connection leads, and the phosphor coating are formed or mounted to a flexible substrate that is sufficiently flexible to be formed into a cylindrical shape[.] Ex. 1001, 22:7–12 (emphasis added). The claim is inartfully written, as it requires the LEDs to comprise a phosphor coating but then separately recites that the LED chips and the phosphor coating are formed or mounted to the substrate. But Petitioner correctly explains that the plain meaning requires that “the LED chips comprise a phosphor coating” and that “the [same] phosphor coating” (included in the LED chips) is “formed or mounted to a flexible substrate.” Reply 2. In other words, the use of the term “the” before “phosphor coating” indicates reliance on the antecedent basis of “LED chips comprise a phosphor coating,” and thus the same coating of the LED chips is formed or mounted to the substrate. Logically, by including a phosphor coating with the LED chips, which are formed or mounted to the substrate, the coating of these chips is also indirectly formed or mounted to the substrate. Conversely, it would be illogical to conclude that the claim recites two phosphor coatings, one attached to the LED chips and another attached directly to the substrate, because the structure of the claim refers to a single phosphor coating of the LED chips. Even Patent Owner concedes that the claim encompasses the phosphor coating indirectly being mounted or attached to the substrate (in addition to being directly attached). PO Resp. 11 (“The ordinary English reading of the claim language does not encompass the phosphor coating only being indirectly attached to the substrate, instead, the language indicates that the coating is directly applied to the substrate.” (emphasis changed)), 13 (“the phosphor coating . . . is not merely attached to the substrate indirectly”).” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “After considering Patent Owner’s arguments, which we address below, we agree with Petitioner that the combination of Wojnarowski and Martin discloses this limitation and that a person of ordinary skill in the art would have been motivated to combine the references’ teachings in the manner asserted by Petitioner. Briefly, we summarize our findings, and then we address the parties’ arguments in more detail. First, we agree with Petitioner, and Patent Owner does not dispute, that Wojnarowski’s AC input voltage would have been converted to DC voltage in light of the bridge rectifier and capacitor disclosed by Wojnarowski. Pet. 25; Ex. 1002 ¶¶ 119– 20 (citing, e.g., Ex. 1005, 7:59–62, Fig. 24); PO Resp. 35–36 (acknowledging Wojnarowski discloses converting an AC input to a DC voltage). Second, we further agree with Petitioner, and Patent Owner does not dispute, that excessive current due to too few LEDs would have harmed Wojnarowski’s LEDs, and too small a current due to too many LEDs would be insufficient to power Wojnarowski’s LEDs. Pet. 26; Ex. 1002 ¶ 134; PO Resp. 48 (discussing, but not disputing, these assertions).13 Third, we agree that a POSITA would have recognized in view of Martin’s teachings and the knowledge of a skilled artisan that when configuring Wojnarowski’s device, the total forward voltage drop of the series-connected LEDs should approximately match the DC voltage output 13 Petitioner explains the relationship between voltage and current for the LEDs as follows: “the total voltage drop of the circuit would dictate the current drawn by the LED circuitry, which would have been known to be inversely proportional to the voltage.” Pet. 26 (citing Ex. 1002 ¶ 134). of Wojnarowski’s circuit. Pet. 26–27 (citing Ex. 1002 ¶¶ 132–38; Ex. 1008, Abstract (LED voltage “must be matched to the input source voltage”), ¶ 60 (“For AC or any other regularly varying input voltage, there is an additional requirement to direct drive voltage matching”)). For example, Martin teaches that “[t]he number of LEDs in the monolithic array may be selected to achieve a particular voltage drop across each device.” Ex. 1006 ¶ 22. Martin further explains, “[t]he voltage across each of the individual LEDs in the array is the line voltage divided by the number of LEDs in series,” and “[t]he number of LEDs is chosen such that the maximum voltage across each individual LED during the peak in the alternating current cycle is low enough so as not to damage the LEDs.” Id. The forward voltage drop across Martin’s 38 LEDs is about 171 V, which matches Martin’s AC input voltage peak of about 169.71 V. See id. (“At 120 RMS volts, the peak voltage will be about 180V [correction: 169.71 V],” and if the LEDs “can tolerate a maximum forward voltage of 4.5V, at least 38 LEDs connected in series are required.” (38 LEDs x 4.5 V = 171 V)); PO Resp. 41–42 (“While Martin references ‘about 180V,’ both parties agree that the correct value of the peak voltage Vp is 169.71 V.” (citing Ex. 1002 ¶ 127)). Although Martin’s LED forward voltage drop (171 V) differs slightly from the peak input voltage (169.71 V), Patent Owner conceded at the hearing that the claimed “matches” does not require an exact equivalence. Tr. 38:9–11 (“Patent Owner agrees . . . that matching has a meaning that goes beyond exact equivalence.”).14” slip op. at 22

  • Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication establishedDecided for petitioner

    “35 U.S.C. § 311(b). PO Resp. 22–25. This statute provides that “[a] petitioner in an inter partes review may request to cancel as unpatentable 1 or more claims of a patent only on a ground that could be raised under section 102 or 103 and only on the basis of prior art consisting of patents or printed publications.” § 311(b) (emphasis added). Patent Owner contends that Martin is not available as prior art under 35 U.S.C. § 311(b) because it is not a patent or printed publication and is only prior art under 35 U.S.C. § 102(e). PO Resp. 22. Patent Owner argues that documents are “printed publications” as of the date they become available to the public, and Martin became public on its publication date of October 21, 2004, after the February 25, 2004 priority date of the ’979 patent. Id. at 23. Patent Owner raises a similar argument for the Soules-II reference in Ground 6. Id. at 25– 26. Petitioner responds that the AIA framework permits the use of § 102(e) prior art in IPR proceedings, unlike formerly available covered business method review (CBM) proceedings, which restricted challenges to § 102(a) prior art. Reply 29. We agree. The statute governing the formerlyavailable CBM proceeding explicitly limits challenges based on “prior art that is described by section 102(a).” AIA § 18(a)(1)(C). In contrast, § 311(b) more broadly permits challenges “on the basis of prior art consisting of patents or printed publications.” The broader language in § 311(b) implies that unlike CBMs, IPRs are not limited to challenges solely under § 102(a) prior art. The parties cite to no Federal Circuit decisions that squarely address this issue. However, the Federal Circuit has applied § 102(e) patent application publication prior art in appeals from IPR proceedings. See, e.g., Purdue Pharma L.P. v. Iancu, 767 Fed. App’x 918, 920–21, 926 (Fed. Cir. 2019) (nonprecedential) (determining that a § 102(e) patent application publication was available as prior art in an IPR). The Board has also long permitted challenges based on patent application publications under § 102(e). See, e.g., Idle Free Sys., Inc. v. Bergstrom, Inc., IPR2012-00027, Paper 14 at 27 (PTAB Jan. 31, 2013) (instituting trial over § 102(e) ground based on a patent application publication). We therefore find Patent Owner’s § 311(b) argument unpersuasive.” slip op. at 34

  Patent outcomesUS 10,652,979 mixed
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 10,652,979
• Renesas Electronics Corporation / Renesas Electronics America, Inc. v. Lone Star Silicon Innovations, LLCSome claims unpatentable
  PTAB · Mar 25, 2019 · IPR2017-01869 · APJ Elizabeth M Roesel · IPR · Final written decision

  Claims 1, 4–6, 9, and 10 are unpatentable as obvious over Igarashi and Tanaka (1999); claims 2 and 7 were not shown unpatentable.

  RulingsFinal written decision

  • Skill levelSkill level patent owner adoptedDecided for patent owner

    “For purposes of our Institution Decision, we accepted the definition of a POSA provided by Dr. Bottoms. Dec. 10–11 (citing Ex. 2001 ¶ 31). Dr. Bottoms provides a “clarification” of the Board’s description, testifying that “[t]he specific industry experience would require process design experience—which is experience beyond managing fabrication equipment.” Ex. 2011 ¶ 36. Dr. Bottoms’ clarification is consistent with the level of skill reflected by the ’330 patent, which discloses process design options for making a low dielectric constant silicon nitride etch stop. Ex. 1001, 5:66-6:24. Dr. Neikirk testifies that, under Dr. Bottoms’ definition, a POSA has a higher degree of skill than under Dr. Neikirk’s definition, and the Board’s adoption of Dr. Bottoms’ definition would not change his opinions regarding obviousness. Ex. 1028 ¶ 14. We find there is little difference between the declarants’ definitions of a POSA, and the outcome of our patentability determinations would be the same, regardless of which definition we accept. For the sake of clarity, we adopt Dr. Bottoms’ definition of a POSA, including the recent clarification. Ex. 2011 ¶¶ 35, 36. We also rely on the cited prior art references as reflecting the level of ordinary skill in the art at the time of the invention. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 12

  • Expert testimonyPetitioner expert creditedPatent owner expert creditedOther

    “After reviewing the qualifications of Dr. Neikirk and Dr. Bottoms, as set forth in each witness’s declaration and curriculum vitae, we find that each of these declarants has sufficient education and experience related to the subject matter of the ’330 patent to testify regarding the perspective of a POSA at the time of the invention. Ex. 1011 ¶¶ 2, 3; Ex. 1012; Ex. 2002; Ex. 2011 ¶¶ 8–20. See Trial Practice Guide Update, 83 Fed. Reg. 39,989 (Aug. 13, 2018), available at https://go.usa.gov/xU7GP (“TPG Update”), 3 (“A person may not need to be a person of ordinary skill in the art in order to testify as an expert under Rule 702, but rather must be ‘qualified in the pertinent art.’” (quoting Sundance, Inc. v. DeMonte Fabricating Ltd., 550 F.3d 1356, 1363–64 (Fed. Cir. 2008))). D.” slip op. at 12

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “In the Institution Decision, we determined that it was not necessary to resolve the parties’ claim construction dispute. Dec. 9–10. Neither party challenges that determination. Petitioner contends that the asserted grounds of unpatentability apply under either party’s construction for the phrase “etch stop layer of silicon nitride.” Pet. 25 n.3. Patent Owner argues that this phrase is not limited to a layer of pure silicon nitride and allows for the presence of dopants and/or impurities. PO Resp. 8–10. Patent Owner does not, however, rely on its proposed claim construction for any patentability argument. In fact, Patent Owner acknowledges that the silicon nitride materials disclosed in the Low-K References satisfy Patent Owner’s proposed construction. PO Resp. 10. Under these circumstances, we agree with Petitioner that we do not need to resolve the parties’ claim construction dispute. Pet. Reply 2. Accordingly, consistent with the Institution Decision, we determine that we do not need to provide an express construction for any claim term for purposes of resolving the controversy. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))). B.” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “copper interconnects need silicon nitride films as an etch stop, but that such films have a high dielectric constant, which causes an undesirable increase in the effective dielectric constant of the interconnect structure and increased parasitic capacitance, as compared with aluminum interconnects. Ex. 1021, 829-1, 829-2; see Pet. 18; Ex. 1011 ¶¶ 92, 93. As Petitioner correctly points out (Pet. 53–54), Tanaka (1999) cites Igarashi as an example of a copper interconnect system that is degraded by parasitic capacitance due to the high permittivity (dielectric constant) of silicon nitride etch stop films. Ex. 1017, 47-1 n.1. Tanaka (1999) discloses a low dielectric constant silicon nitride etch stop film as a solution to the problem of parasitic capacitance in copper damascene interconnect structures, such as Igarashi’s. Id. at 47-1, 47-2 (“New low-k SiN film, with a permittivity of 5.4 . . . should be the solution to realize Cu damascene interconnects . . . .”). Consistent with these express disclosures, Dr. Neikirk persuasively testifies that “Igarashi identifies a need for a low-k dielectric etch stop layer” and “Tanaka (1999) meets this need.” Ex. 1011 ¶ 94; see Pet. 18 (citing Ex. 1011, § VIII.C., which contains paragraph 94 of Dr. Neikirk’s testimony). Accordingly, we find Petitioner has shown by a preponderance of the evidence that a POSA would have been motivated to use the low dielectric constant silicon nitride etch stop film of Tanaka (1999) as the etch stop layer in the interconnect system of Igarashi. Patent Owner disputes whether Petitioner has established a reasonable expectation of success for the combination of Tanaka (1999)’s low dielectric constant silicon nitride etch stop film and Igarashi’s interconnect structure. PO Resp. 65. Although the Petition does not expressly discuss whether one of ordinary skill in the art would have had a reasonable expectation of success in combining Tanaka and Igarashi to arrive at the claimed invention, Petitioner shows a very close relationship between the teachings of Tanaka (1999) and Igarashi. Pet. 12–13, 17–18, 53–62. As discussed above and argued by Petitioner, Tanaka (1999): (1) cites Igarashi as an example of a copper interconnect system that suffers from parasitic capacitance due to the high dielectric constant of silicon nitride etch stop films, and (2) discloses a low dielectric constant silicon nitride etch stop film as a solution to the parasitic capacitance problem exemplified by Igarashi. Pet. 13, 18, 53–54; Ex. 1011 ¶¶ 74–79, 88–94; Ex. 1017, 47-1 & n.1; Ex. 1021, 829-1, 829-2. Petitioner establishes a reasonable expectation of success for the combination of Tanaka (1999) and Igarashi by demonstrating a strong correlation between the problem discussed by Igarashi—the high dielectric constant of silicon nitride films when used as etch stops for copper interconnects—and the solution disclosed by Tanaka (1999)—a low dielectric constant silicon nitride film for use as an etch stop layer in copper damascene interconnect structures. In re Inland Steel Co., 265 F.3d 1354, 1364 (Fed. Cir. 2001) (“[T]he strength of the correlation between the references gives rise to a reasonable expectation of success from combining them.”).” slip op. at 27

  Patent outcomesUS 6,388,330 mixed
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 6,388,330
• Pfizer, Inc. / Samsung Bioepis Co., Ltd. v. Genentech, IncSome claims unpatentable
  PTAB · Nov 29, 2018 · IPR2017-01489 · APJ Zhenyu Yang · IPR · Final written decision

  The Board held claims 1, 2, 4, 12, 25, 29–31, 33, 42, 60, 62–64, 66, 67, 69, 71, 73, 74, 78, 80, and 81 unpatentable as obvious; claims 65, 72, 75–77, and 79 were not …

  RulingsFinal written decision

  • Skill levelSkill level patent owner adoptedDecided for patent owner

    “Level of Ordinary Skill in the Art In the Decision to Institute, we found the parties’ proposed definitions of a person of ordinary skill for the ’213 patent are similar. Dec. 7 (citing Pet. 16; Prelim. Resp. 17). We adopted Patent Owner’s proposed definition that “[a] person of ordinary skill for the ’213 patent would have had a Ph.D. or equivalent in chemistry, biochemistry, structural biology, or a closely related field, and experience with antibody structural characterization, engineering, and/or biological testing, or an M.D. with practical academic or industrial experience in antibody development.” Id. During trial, Patent Owner points out that Petitioner’s proposed definition “encompasses persons without advanced degrees but who have ‘knowledge gained through 4–5 years of work experience.’” PO Resp. 17. A person of ordinary skill in the art is a hypothetical person who is presumed to know the relevant prior art. Custom Accessories, Inc. v. Jeffrey–Allan Indus., Inc., 807 F.2d 955, 962 (Fed. Cir. 1986). The artisan may gain such knowledge through either formal education or extensive work experience. Thus, we do not discern an appreciable difference in the parties’ respective definitions of the level of ordinary skill in the art, and any perceived distinction does not impact our Decision. Having considered the complete record developed at trial, we see no reason to change our assessment.” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Lexicography (patentee as own lexicographer)Term construed patent owner constructionDecided for patent owner

    “In the Decision to Institute, we agreed with Patent Owner that the ’213 patent expressly defined “consensus human variable domain,” which appears in claims 4, 33, 62, and 69, to mean “a human variable domain which comprises the most frequently occurring amino acid residues at each location in all human immunoglobulins of any particular subclass or subunit structure.” Dec. 9–10; Ex. 1501, 11:32–38. During trial, the parties did not argue otherwise, and we see no reason to change our position as to claim construction. See PO 17–18; Reply 5. We, however, clarify that “all” in the consensus of “all human immunoglobulins” is not in the literal sense. In fact, Patent Owner does not appear to argue otherwise.7 Dr. Wilson, the expert witness for Patent 7 In a parallel proceeding involving the same patent, counsel for Patent Owner acknowledged that the term “all human immunoglobulins” refers to Owner, testified that the consensus sequence of the ’213 patent was “derived from ‘all’ known antibody sequences of any particular subclass or subunit structure.” Ex. 2041 ¶ 210 (emphasis added); see also PO Resp. 52 (arguing the same); Ex. 1698, 59:22–60:1 (Dr. Carter testifying that the consensus sequence, as defined in the ’213 patent, “only describes what was known at that time or it’s only available sequences at that -- at that time”); Ex. 1699, 35:9–16 (Dr. Presta explaining that the consensus sequence of the ’213 patent had the most common residue at every position “for the sequences that were available”). And evidence of record shows that at the priority date of the ’213 patent, the sequences that were listed in Kabat 1987 “were the sequences available.” Ex. 1699, 35:9–20; see also Ex. 2016 ¶ 25 (Kabat 1987 “collected known sequence data of antibodies”); Ex. 1698, 60:13–25 (Dr. Carter explaining the consensus sequence was derived from Kabat 1987, which is what was available at the time of the ’213 patent); Ex. 1699, 27:19–25 (Dr. Presta stating that “Elvin Kabat had taken all known human/mouse/rabbit antibody sequences, published them in a government publication, and that there were human subgroups of sequences within the heavy and the light chains”).” slip op. at 11

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “For the purpose of this Decision, we see no need to expressly construe any other claim terms. Wellman, Inc. v. Eastman Chem. Co., 642 F.3d 1355, 1361 (Fed. Cir. 2011) (stating claim terms need only be construed to the extent necessary to resolve the controversy).” slip op. at 13

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “When there is a design need or market pressure to solve a problem and there are a finite number of identified, predictable solutions, a person of ordinary skill has good reason to pursue the known options within his or her technical grasp. If this leads to the anticipated success, it is likely the product not of innovation but of ordinary skill and common sense. KSR, 550 U.S. at 421. Here, Queen 1989 recognizes the need to substitute framework residues in order to “reduce immunogenicity while retaining high binding affinity.” See Ex. 1534, 3. Thus, even if Queen 1990 is not available as prior art, we find that an ordinary artisan would have identified the candidates for substitution, as recited in claims 12, 42, 60, 71, 73, and 74. Indeed, Dr. Wilson testified that he performed a “good analysis” and identified 19 amino acid positions in the light chain and 19 in the heavy chain, including 66L (recited in claims 12 and 42), 73H (recited in claim 71), 78H (recited in claims 60 and 73), 93H (recited in claim 74). Ex. 1697, 242:4–6; Ex. 2041 ¶ 186, Appendix 1. Claims 12, 66, 67, 71, 73, 74, and 78” slip op. at 22

  Patent outcomesUS 6,407,213 mixed
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 6,407,213

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.