• Aroma360, LLC v. Air Esscentials, Inc.Some claims unpatentable
  PTAB · Oct 6, 2026 · IPR2025-00707 · APJ Eric C Jeschke · IPR · Final written decision

  Claim 5 is unpatentable over Gao-2 and over Gao-2 with Goubet; claims 1, 3, 4, and 6–8 were not shown unpatentable on any ground, and substitute claim 17 was denied.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “As noted in the Decision on Institution, Petitioner’s proposed definition appears generally consistent with the record, including the prior art. See Dec. Inst. 8 (citing In re GPAC Inc., 57 F.3d at 1579). We remove the phrase “at least” in both listed options, however, as that phrase adds ambiguity. Further, Patent Owner has not argued at trial that Petitioner’s proposal for the level of ordinary skill leads to an improper understanding of how a skilled artisan would have understood either the challenged patent or the prior art. In the analysis below, we continue to apply the level of ordinary skill in the art adopted in the Decision on Institution, as proposed by Petitioner.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Neither Petitioner nor Patent Owner propose explicit constructions for any claim terms. Pet. 16–17; PO Resp. 5–6. Based on the complete record, we need not construe explicitly any claim terms because doing so would not change the outcome of the analysis below. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 10

  • Expert testimonyPetitioner expert creditedDecided for patent owner

    “As an initial matter, the record here does not support any sound basis to disregard the entirety of Dr. Micklow’s Declaration for allegedly not reviewing the parties’ claim constructions. See Pet. Reply 2–3 (citing Ex. 1046, 115:15–18). Contrary to Petitioner’s argument, in the cited 11 This refers to the recitation in clauses 1F and 5F that the “diffusion assembly is disposed between said upper chamber and said lower chamber.” discussion, Dr. Micklow does not indicate that he applied an incorrect understanding of a claim term. Cf. Cordis Corp. v. Bos. Sci. Corp., 658 F.3d 1347, 1357–58 (Fed. Cir. 2011) (disregarding testimony “based on an incorrect understanding of the claim construction”), cited at Pet. Reply 1; see also Pet. Reply 3 (arguing that “Dr. Micklow’s opinion that the prior art does not render the claims obvious is premised on an interpretation of certain claim limitations that are inconsistent with both parties’ constructions” (emphasis added)). Instead, we read Dr. Micklow’s testimony as clarifying that he was not involved in claim construction at all and that, as stated, he “made [his] opinions based on what [he] read in the patents.” Ex. 1046, 112:11–12; see also id. at 115:15–18 (“I don’t know if I would even apply claim construction. I applied engineering principles to a document that had been published with the patent office.”).” slip op. at 12

  • BurdenNot shown unpatentable

    “referring to the same direction as the separation of the “upper chamber” and “lower chamber” (vertically in both Figure 6 of the challenged patent and Figure 1 of Goubet), we turn back now to Petitioner’s discussion of clause 1F, which includes the limitation at issue. There, Petitioner does not discuss why the “diffusion assembly” is allegedly “disposed between” the “upper chamber” and “lower chamber,” but instead, Petitioner discusses why a component of the “diffusion assembly”—the “atomizer assembly”—is allegedly “disposed between” the “upper chamber” and “lower chamber”: Pet. 39. In the end, we need not assess whether the “atomizer assembly” identified by Petitioner is “disposed between” the “upper chamber” and “lower chamber” under the proper construction of that term (which, again, we need not and do not determine here) because the “disposed between” limitation does not involve the “atomizer assembly.” Instead, we find that, by failing to address why the identified “diffusion assembly” is “disposed between” the identified “upper chamber” and “lower chamber,” Petitioner has failed to provide persuasive evidence that Goubet discloses or suggests the “disposed between” limitation. Pet. 38–39 (discussing the claim language “said diffusion assembly is disposed between said upper chamber and said lower chamber” but only discussing the location of the “atomizer assembly”); see 35 U.S.C. § 316(e) (“In an inter partes review . . . , the petitioner shall have the burden of proving a proposition of unpatentability by a preponderance of the evidence.”). For the reasons above, we find, based on the complete record, that Petitioner has not shown by a preponderance of the evidence that Goubet discloses or suggests the “disposed between” limitation.” slip op. at 22

  Patent outcomesUS 10,092,918 mixed
  Claim construction§ 103 obviousnesscites Phillips · KSR
  Patents in suitUS 10,092,918
• Imperative Care, Inc. v. Inari Medical, Inc.All claims unpatentable
  PTAB · Oct 6, 2026 · IPR2025-00728 · APJ Timothy G Majors · IPR · Final written decision

  Claims 1–7, 9, 10, 15–18, and 20–24 are unpatentable as obvious over Schaffer with Hartley or Eller; claims 1–3, 5, 6, 9, 15–18, and 21–24 are also obvious over Hartley and Eller.

  RulingsFinal written decision

  • Skill levelSkill level board ownDecided for patent owner

    “Petitioner’s proposed POSA definition lacks specificity. That definition, if interpreted generically, could mean that a person may qualify as a POSA if they had, for example, a B.S. in mechanical engineering and only two years of experience designing any type of product in any field. That is too broad. We find that a POSA would have had the agreed-upon educational credentials—an undergraduate degree in mechanical engineering or a related engineering discipline. Ex. 1003 ¶ 35; Ex. 2033 ¶ 61. We find that a POSA would also have had 2–4 years of design or engineering experience related to products in the field of the invention, which involves endovascular devices and the surgical procedures that use such devices. Ex. 1001, 1:16–54 (background of the invention). Such devices include, but are not limited to, hemostasis valves and catheters for testimony of the parties’ experts, the POSA need not have had first-hand experience designing hemostasis valves. See, e.g., Ex. 1037 (Zalesky Tr.), 72:11–73:7 (testifying direct experience “designing” hemostasis valves or aspiration catheters is not necessary, but “general experience with vascular devices and procedures” is required). Further, as Dr. Zalesky testified, the POSA’s experience related to developing such devices “could be as simple as bench testing and looking at clinical data.” Id. at 74:5–75:1. Lastly, a POSA would have understood such devices’ design requirements as determined by the needs of the physician, patient, and procedure, which understanding may be informed by work experience or study. Ex. 2030, 24:5–21.” slip op. at 12

  • Expert testimonyPetitioner expert creditedPatent owner expert creditedMixed

    “above (supra Section III.C), a filament requires flexibility, Petitioner has not demonstrated that Schaffer describes that feature in its valves. Instead, Patent Owner persuades us that Schaffer describes “rigid U-shaped actuating members—not a ‘filament.’” PO Resp. 23–24.13 We find Dr. Zalesky’s interpretation of Schaffer more credible than Mr. Thornton’s on the question of whether a POSA would have regarded Schaffer’s actuating members as being substantially rigid structures. Ex. 2033 ¶¶ 91–100 (testifying, inter alia, that a POSA would have understood from Schaffer’s disclosure about making the actuator and actuating members from machining pre-existing amounts of metals and/or plastics, and further explaining that flexible parts would deform and be difficult to machine through conventional techniques); Ex. 1005 ¶¶ 81–82. Mr. Thornton testifies that Schaffer’s disclosed manufacturing techniques for the actuator/actuating members are only examples and “a person of ordinary skill in the art could have simply purchased pre-made [and flexible] flat wire or plastic tapes or ribbons.” Ex. 1003 ¶ 79. Such testimony invokes, at best, obviousness-based reasoning. This does not establish that Schaffer alone describes a filament sufficient to anticipate the claims. Trintec Indus., Inc. v. Top-U.S.A. Corp., 295 F.3d 1292, 1296 (Fed.” slip op. at 28

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed patent owner constructionDecided for patent owner

    “Patent Owner cites intrinsic evidence in support of its interpretation, which include claim 1’s recitation of an “active tensioning mechanism” comprising the filament and the Specification’s description of a filament that can be both “loosened” and “tightened.” PO Resp. 14–17 (citing, e.g., Ex. 1001, 9:36–37, 9:53–56 (teaching “the filament 150 is tightened” when the actuator buttons are released and “the filament 150 is loosened” when the buttons are pressed to open the valve)); see also Ex. 2025, 1288 (defining “tension” as to “tighten to a desired or appropriate degree”). These descriptions from the patent are more consistent with the view that the filament is characteristically flexible, not rigid. 10 We reached the same conclusion, based on substantially the same records, in the Institution Decision and the Final Written Decisions in the 1157, 156, and 289 IPRs. Inst. Dec. 14–18; Ex. 1042, 14–24; Ex. 1048, 16–23; Ex. 1049, 14–17 (noting the parties’ agreement at oral hearing that there was no additional argument or evidence about whether a filament requires flexibility that was not already addressed in related matters). After we construed the “filament” term to require flexibility at institution, Petitioner provided no further argument or evidence on this issue in its authorized trial briefing or at oral hearing. See generally Pet. Reply. embodiments (where the filament forms one or more loops like depicted and described in Figures 6–7) require a flexible structure. See, e.g., Ex. 2032, 15–16 (explaining that the device would not work to constrict the tubular sidewall and lumen (analogous to the elongate member defining a lumen of the claims here) if the filament forming the loop(s) was inflexible); Ex. 1001, Figs. 6–7 (filament 150, with sub-filaments 150-A and 150-B). Although flexibility of the filament in the patent’s “bight” embodiments (e.g., as shown in Figures 8 and 9) is less clear, there is a dearth of evidence from Petitioner—either intrinsic or extrinsic to the patent—showing why a POSA would have understood the bights as embracing rigid structures. See Ex. 1001, Figs. 8–9. Moreover, as admitted by Petitioner’s expert, that a filament may be made from various materials described in the patent (e.g., synthetics or metals) does not, absent more information, lead to a conclusion that a filament is “rigid.” Ex. 2030, 125:2–126:4 (testifying “the relative stiffness or rigidity is not clear from those . . . materials without knowing much more information”).” slip op. at 16

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

    “We find that Petitioner has not shown, by a preponderance of the evidence, that Schaffer anticipates claim 1 or any of the other challenged claims, each of which requires at least one “filament.” We are unpersuaded above (supra Section III.C), a filament requires flexibility, Petitioner has not demonstrated that Schaffer describes that feature in its valves. Instead, Patent Owner persuades us that Schaffer describes “rigid U-shaped actuating members—not a ‘filament.’” PO Resp. 23–24.13 We find Dr. Zalesky’s interpretation of Schaffer more credible than Mr. Thornton’s on the question of whether a POSA would have regarded Schaffer’s actuating members as being substantially rigid structures. Ex. 2033 ¶¶ 91–100 (testifying, inter alia, that a POSA would have understood from Schaffer’s disclosure about making the actuator and actuating members from machining pre-existing amounts of metals and/or plastics, and further explaining that flexible parts would deform and be difficult to machine through conventional techniques); Ex. 1005 ¶¶ 81–82. Mr. Thornton testifies that Schaffer’s disclosed manufacturing techniques for the actuator/actuating members are only examples and “a person of ordinary skill in the art could have simply purchased pre-made [and flexible] flat wire or plastic tapes or ribbons.” Ex. 1003 ¶ 79. Such testimony invokes, at best, obviousness-based reasoning. This does not establish that Schaffer alone describes a filament sufficient to anticipate the claims. Trintec Indus., Inc. v. Top-U.S.A. Corp., 295 F.3d 1292, 1296 (Fed.” slip op. at 27

  Patent outcomesUS 11,844,921 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,844,921
• Aroma360, LLC v. Air Esscentials, Inc.All claims unpatentable
  PTAB · Oct 6, 2026 · IPR2025-00706 · APJ Eric C Jeschke · IPR · Final written decision

  Claims 1, 4, and 7–10 are unpatentable as obvious over Goubet and anticipated by Gao; proposed substitute claims 20 and 21 are denied as indefinite and lacking written-description support.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “In the Response, Patent Owner states that it “does not dispute” the definition of one of ordinary skill in the art proposed by Petitioner, but Patent Owner “reserves the right to address [the definition] should new issues materialize.” PO Resp. 6. Patent Owner did not address this issue in the Sur-reply. As noted in the Decision on Institution, Petitioner’s proposed definition appears generally consistent with the record, including the prior art. See Dec. Inst. 8 (citing In re GPAC Inc., 57 F.3d at 1579). We remove the phrase “at least” in both listed options, however, as that phrase adds ambiguity. Further, Patent Owner has not argued at trial that Petitioner’s proposal for the level of ordinary skill leads to an improper understanding of how a skilled artisan would have understood either the challenged patent or the prior art. In the analysis below, we continue to apply the level of ordinary skill in the art adopted in the Decision on Institution, as proposed by Petitioner.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed petitioner constructionOther

    “Network LLC, 929 F.3d 1350, 1357 (Fed. Cir. 2019). At first glance, the language of the limitation at issue—which, again, recites “the compressed air and the operative fluid mix together in said mixing chamber to form the fluid dispersion”—would seem to require the “fluid dispersion” (under the stipulated construction) to be fully formed in the “mixing chamber.” In other words, the language of the limitation alone would seem to support Patent Owner’s proposed construction for the “form the fluid dispersion” limitation. But the claim construction analysis does not end with consideration of the claim language alone. Next, we turn to the Specification. The Federal Circuit has said that the specification “is the single best guide to the meaning of a disputed term.” Phillips, 415 F.3d at 1315 (quoting Vitronics Corp. v. Conceptronic, Inc., 90 F.3d 1576, 1582 (Fed. Cir. 1996)). Here, the discussion in the Specification of precisely the same language as in the limitation at issue strongly supports that “to form a fluid dispersion” in the limitation at issue requires only initial mixing of the compressed air and operative fluid in the mixing chamber, with further “formation” of the ”fluid dispersion” occurring downstream of the mixing chamber: More importantly, the “predetermined amount” of compressed air and the “preselected amount” of the operable fluid are initially mixed together in the mixing chamber 226 to form a fluid dispersion. The diffusion chamber 112" is further structured to facilitate the formation of a plurality of substantially uniform droplets, as defined hereinabove, in the fluid dispersion prior to discharge from the diffusion chamber 112" through discharge port 132. Ex. 1001, 10:62–11:2 (emphasis added) (discussing Figure 6), quoted, in part, at Pet. Reply 6–710; see also Ex. 1001, 5:64–6:4 (same language, except without double primes, in a discussion of Figures 1 and 2). To be sure, certain passages in the Specification could be read to indicate that a “fluid dispersion” must be fully formed in the “mixing chamber.” See, e.g., Ex. 1001, 6:11–12 (“More in particular, the suppression chamber 232 receives the fluid dispersion from the mixing chamber 226.”); see also id. at 7:22–33, 11:39–52 (both implying that a “fluid dispersion” is formed in the mixing chamber). But the passage block quoted directly above (and the similar one bridging columns 5 and 6) more directly addresses the issue at hand—i.e., the scope of “form the fluid dispersion”—by using the same” slip op. at 13

  • Expert testimonyPatent owner expert discountedMixed

    “As an initial matter, the record here does not support any sound basis to disregard the entirety of Dr. Micklow’s Declaration for allegedly not reviewing the parties’ claim constructions. See Pet. Reply 2 (citing Ex. 1046, 115:15–18). Contrary to Petitioner’s argument, in the cited discussion, Dr. Micklow does not indicate that he applied an incorrect understanding of a claim term. Cf. Cordis Corp. v. Bos. Sci. Corp., 658 F.3d 1347, 1357–58 (Fed. Cir. 2011) (disregarding testimony “based on an incorrect understanding of the claim construction”), cited at Pet. Reply 1. Instead, we read Dr. Micklow’s testimony as clarifying that he was not involved in claim construction at all and that, as stated, he “made [his] opinions based on what [he] read in the patents.” Ex. 1046, 112:11–12; see also id. at 115:15–18 (“I don’t know if I would even apply claim construction. I applied engineering principles to a document that had been published with the patent office.”).” slip op. at 18

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable

    “To satisfy its burden of proving obviousness, a petitioner cannot employ mere conclusory statements. The petitioner must instead articulate specific reasoning, based on evidence of record, to support the legal conclusion of obviousness.” In re Magnum Oil Tools Int’l, Ltd., 829 F.3d 1364, 1380 (Fed. Cir. 2016); TriVascular, Inc. v. Samuels, 812 F.3d 1056, 1066 (Fed. Cir. 2016) (“Although the KSR test is flexible, the Board ‘must still be careful not to allow hindsight reconstruction of references . . . without any explanation as to how or why the references would be combined to produce the claimed invention.’”) (citation omitted). Based on the complete record, we agree with Patent Owner that “Petitioner’s asserted motivation boils down to the conclusory statement that given Goubet and Kaiser, ‘it was well known in the field at the time of the invention that droplets of greater uniformity result in uniform droplet evaporation.’” PO Resp. 31 (quoting Pet. 59). We agree with Patent Owner that Petitioner’s discussion of the alleged reasons to combine (Pet. 59) is insufficient to support the proposed combination here. See Magnum Oil, 829 F.3d at 1380. Specifically, we are not persuaded that Kaiser’s teachings—which relate to combustion (Ex. 1014 at 43)—would have led one of ordinary skill in the art to the proposed modifications, which would allegedly “improve the smoothness (i.e., less harsh) of the aroma generated as the oil droplets evaporate in the surrounding airspace.” See Pet. 59 (emphasis added); White Pet. Decl. ¶ 251 (same); see PO Resp. 32 (“Rather, Dr. White merely describes the ability to achieve the effect as in the claimed patent, not why a [person of ordinary skill in the art] would look to the field of electrospray injection and combustion in mesoscale power-generation systems, using high-voltage electric fields to generate charged fuel droplets for controlled combustion in catalytic micro-combustors when considering atomization for scents.”). For these reasons, we determine, in light of the complete record, that Petitioner has not shown by a preponderance of the evidence that one of ordinary skill in the art at the time of the invention would have had reason to combine Goubet and Kaiser, as proposed. slip op. at 32

  Patent outcomesUS 10,583,449 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · Nautilus
  Patents in suitUS 10,583,449
• Aroma360, LLC v. Air Esscentials, Inc.All claims unpatentable
  PTAB · Oct 6, 2026 · IPR2025-00705 · APJ Eric C Jeschke · IPR · Final written decision

  Claims 7–9 and 11 are unpatentable as obvious over Goubet; proposed substitute claim 21 is denied as indefinite.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “In the Response, Patent Owner states that it “does not dispute” the definition of one of ordinary skill in the art proposed by Petitioner, but Patent Owner “reserves the right to address [the definition] should new issues materialize.” PO Resp. 5. Patent Owner did not address this issue in the Sur-reply. As noted in the Decision on Institution, Petitioner’s proposed definition appears generally consistent with the record, including the prior art. See Dec. Inst. 8 (citing In re GPAC Inc., 57 F.3d at 1579). We remove the phrase “at least” in both listed options, however, as that phrase adds ambiguity. Further, Patent Owner has not argued at trial that Petitioner’s proposal for the level of ordinary skill leads to an improper understanding of how a skilled artisan would have understood either the challenged patent or the prior art. In the analysis below, we continue to apply the level of ordinary skill in the art adopted in the Decision on Institution, as proposed by Petitioner.” slip op. at 9

  • Expert testimonyPetitioner expert creditedDecided for patent owner

    “The record here does not support any sound basis to disregard the entirety of Dr. Micklow’s Declaration, as asserted in Petitioner’s overall argument. See Pet. Reply 1–2. Contrary to Petitioner’s argument, in the cited general discussion, Dr. Micklow does not indicate that he applied an incorrect understanding of a claim term. Cf. Cordis Corp. v. Bos. Sci. Corp., 658 F.3d 1347, 1357–58 (Fed. Cir. 2011) (disregarding testimony “based on an incorrect understanding of the claim construction”), cited at Pet. Reply 1; see also Pet. Reply 2 (arguing that “Dr. Micklow’s declaration is premised on understandings of claim scope that are inconsistent with the constructions advanced by both of the parties” (emphasis added)). Instead, we read the cited portions of Dr. Micklow’s testimony as clarifying that he was not involved in claim construction at all and that, as stated, he “made [his] opinions based on what [he] read in the patents.” Ex. 1046, 112:11–12; see also Pet. Reply 1 (citing Ex. 1046, 112:4–12, 113:13–20, 115:15–18). Next, we turn to each of the four specific claim terms that Petitioner highlights in its further arguments.” slip op. at 12

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction needed

    “B. Claim Construction In inter partes reviews, the Board interprets claim language using the same claim construction standard that would be used in a civil action under 35 U.S.C. § 282(b), as described in Phillips v. AWH Corp., 415 F.3d 1303 (Fed. Cir. 2005) (en banc). See 37 C.F.R. § 42.100(b). Under that standard, we generally give claim terms their ordinary and customary meaning, as would be understood by a person of ordinary skill in the art at the time of the invention, in light of the language of the claims, the specification, and the prosecution history. See Phillips, 415 F.3d at 1313–14. Although extrinsic evidence, when available, may also be useful when construing claim terms under this standard, extrinsic evidence should be considered in the context of the intrinsic evidence. See id. at 1317–19. Neither Petitioner nor Patent Owner propose explicit constructions for any claim terms. Pet. 10–11; PO Resp. 5. Based on the complete record, we need not construe explicitly any claim terms because doing so would not change the outcome of the analysis below. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for patent owner

    “Florida Litigation a Joint Claim Construction statement that included stipulated claim constructions and disputed claim constructions for terms in the challenged patent as well as the ’449 patent and the ’918 patent. See Ex. 1018, Exhibit A (Stipulated Claim Constructions), Exhibit B (Disputed Claim Constructions). The parties stipulated to the construction of the terms “fluid dispersion” and “baffle” as recited in the challenged claim. See id., Exhibit A.10 10 When staying the Florida Litigation, the District Court cancelled the scheduled claim construction hearing. See ECF No. 67 (April 8, 2025) (granting joint motion to stay); ECF No. 68 (April 8, 2025) (cancelling the The stipulated construction of “fluid dispersion” merely restates the express definition of “fluid dispersion” from the challenged patent (although the definition is not cited or discussed in the parties’ filing). Compare Ex. 1018, Exhibit A, with Ex. 1001, 3:8–20. Similarly, the stipulated construction of “baffle” essentially parrots one sentence in the challenged patent (again, not cited or discussed in the parties’ filing). Compare Ex. 1018, Exhibit A, with Ex. 1001, 7:57–59. To the extent necessary, we determine that the complete record supports the parties’ stipulated constructions of “fluid dispersion” and “baffle,” and we apply those constructions below.” slip op. at 10

  Patent outcomesUS 9,527,094 unpatentable
  Claim construction§ 103 obviousness§ 112 disclosurecites Phillips · Nautilus
  Patents in suitUS 9,527,094
• Kubota North America Corporation v. Vermeer Manufacturing CompanySome claims unpatentable
  PTAB · Jun 30, 2026 · IPR2025-00167 · APJ Meredith C Petravick · IPR · Final written decision

  Claims 1–13, 21, 22, 64, and 65 are unpatentable over the asserted grounds; claims 15, 17, 19, 20, 23–30, 66, and 67 were not shown unpatentable over KR996, JP705, and Beltrami.

  RulingsFinal written decision

  • ExcludeMotion to exclude, deniedDenied

    “B. Analysis “The moving party has the burden of proof to establish that it is” slip op. at 9

  • Skill levelOther

    “B. Level of Ordinary Skill in the Art We review the grounds of unpatentability in view of the” slip op. at 21

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownPrior construction adoptedDecided for petitioner

    “lexicographical, we agree with the parties that “mainframe” is not limited to a single weldment. Pet. Init. CC Br. 1; PO Init. CC Br. 1–2. Instead, a single-weldment “mainframe” is merely one disclosed embodiment. See Pet. Init. CC Br. 3 (stating that “by including the term ‘generally’ in a statement, the feature (i.e., single weldment) is expressly identified as merely included in some, but not all embodiments”); PO Init. CC Br. 3 (“This language is merely exemplary, using reference numerals to refer to the embodiment’s features and qualifying ‘single weldment’ as referring ‘generally’ to specific embodiments.”). The Iowa District Court reached the same conclusion. See Ex. 1020 at 4 (holding that “‘mainframe’ will be given its plain and ordinary meaning and does not require a single weldment” (emphasis added)), cited at Pet. Init. CC Br. 2; see also 37 C.F.R. § 42.100(b) (“Any prior claim construction determination concerning a term of the claim in a civil action, or a proceeding before the International Trade Commission, that is timely made of record in the inter partes review proceeding will be considered.”).” slip op. at 33

  • Obviousness (§103) › Objective indicia / secondary considerationsObjective indicia no nexusDecided for petitioner

    “probative and cogent evidence in the record” and “may often establish that an invention appearing to have been obvious in light of the prior art was not.” Transocean Offshore Deepwater Drilling, Inc. v. Maersk Drilling USA, Inc., 699 F.3d 1340, 1349 (Fed. Cir. 2012). Thus, notwithstanding what the teachings of the prior art would have suggested to one skilled in the art, secondary considerations (objective evidence of non-obviousness) may lead to a conclusion that the challenged claims would not have been obvious. In re Piasecki, 745 F.2d 1468, 1471–72 (Fed. Cir. 1984). Our obviousness analysis includes consideration and weighing of Patent Owner’s objective indicia of non-obviousness.” slip op. at 55

  Patent outcomesUS 9,321,386 mixed
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,321,386
• Imperative Care, Inc. v. Inari Medical, Inc.All claims unpatentable
  PTAB · Jan 16, 2026 · IPR2024-01157 · APJ Timothy G Majors · IPR · Final written decision

  Claims 1–9 are unpatentable: the Board found them obvious over Schaffer with Hartley or Eller, though Schaffer alone did not anticipate and Hartley with Eller did not show claims 1–3, 5, 6, and 9.

  RulingsFinal written decision

  • Skill levelSkill level patent owner adoptedDecided for patent owner

    “background for the POSA, but we agree with Patent Owner that Petitioner’s proposed POSA definition lacks some specificity concerning the POSA’s work experience. That definition, if interpreted generically, could mean that a person qualifies as a POSA if they had, for example, a B.S. in mechanical engineering and only two years of experience designing any type of product in any field. That is too broad. We find that a POSA would have had the agreed-upon educational credentials—an undergraduate degree in mechanical engineering or a related engineering discipline. Ex. 1003 ¶ 35; Ex. 2008 ¶ 68. We also find that a POSA would have had 2–4 years of design or engineering experience related to products in the field of the invention, which involves endovascular devices and the surgical procedures that use such devices. Ex. 1001, 1:21–57 (background of the invention). Such devices include, but are not necessarily limited to, hemostasis valves and catheters for minimally-invasive vascular surgeries. Id. And, consistent with the testimony of the parties’ experts, the POSA need not have had firsthand experience designing hemostasis valves. See, e.g., Ex. 1015 (Zalesky Tr.), 72:11–73:7 (testifying direct experience “designing”” slip op. at 13

  • Expert testimonyPetitioner expert creditedOther

    “Schaffer’s valve to include a single flexible string or wire that replaces the two U-shaped actuating members would have been seen by the POSA as potentially advantageous—giving further reason for the POSA to have made that change. Pet. 35–36. We credit Mr. Thornton’s testimony that a POSA would have understood that Schaffer’s U-shaped actuating members may into the lumen. Ex. 1003 ¶ 81. On the other hand, a POSA would have recognized that a single flexible string or wire that is looped completely around the exterior of the seal module/lumen would provide more uniform constriction and compression around the outer diameter of some commonlyused tools and including tools with diverse shapes and sizes. Ex. 1003 ¶¶ 80–88, 93–100. We observed this same reason for modifying the art at institution and, after considering the full trial record, our view has not changed. Inst. Dec. 37 (preliminarily finding that a POSA would have considered Hartley’s string or Eller’s wire “as providing expected benefits insofar as such a filament may more precisely and uniformly constrict a lumen against inserted tools of different sizes and shapes”). Patent Owner’s expert, Dr. Zalesky, does not disagree that a flexible string or wire would have carried this advantage. Ex. 2008 ¶ 75 (testifying a “filament changes shape dynamically, allowing for better adaptability to the contours of the valve lumen as it is constricted”);21 Ex. 1015 (Zalesky Tr.), 86:19–87:4 (testifying that POSAs in 2017 would have recognized that the “cinching” effect provided by a filament would have been more effective for large-bore catheters based on “simple mechanical engineering and physics”). And, at the oral hearing, Patent Owner agreed that using Hartley’s string in Schaffer would help eliminate potential fluid gaps; but Patent Owner qualified its answer that such a benefit would allegedly only have arisen if “the highly-compliant” seal member material in Schaffer was removed,” slip op. at 53

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

    “that issue, after considering the full record developed through trial, we agree with Patent Owner that a “filament” as claimed is flexible. On balance, the evidence supports Patent Owner’s interpretation. Patent Owner cites the claim language, including the recitation that “the filament circumferentially constricts the lumen to create a seal,” which Dr. Zalesky opines a POSA would have understood as implying a flexible structure. PO Resp. 25–26; Ex. 2008 ¶¶ 71–76 (testifying, inter alia, that “[t]o ‘circumferentially constrict,’ the filament must be flexible and extend circumferentially about the lumen” such that “the filament will adapt to the shape of the lumen as the lumen is constricted and thus ‘circumferentially constrict’ the lumen as recited in Claim 1”).12 The Specification also describes the filament as being selectively “tightened” and “loosened” about the elongate member. Ex. 1001, 9:37–40, 9:55–59 (teaching “the filament 150 is tightened” when the actuator is released and “the filament 150 is loosened” when the actuator is pressed to open the valve)). Dr. Zalesky opines that a POSA would have understood the patent’s description of” slip op. at 18

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

    “challenge fails on this record whether the clearer prosecution drawings in Exhibit 1008 are considered in the analysis of anticipation by Schaffer, or not. Whether those prosecution drawings are considered “extrinsic evidence” to Schaffer (as argued by Patent Owner) or publicly-available “intrinsic evidence” with respect to Schaffer (as Petitioner argues) does not change our Decision on Ground 1. Opp. 10–11; Mot. Reply, 3–5. Patent Owner’s motion is, therefore, moot as to Ground 1.” slip op. at 72

  Patent outcomesUS 11,697,011 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,697,011
• Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing denied
  PTAB · Oct 7, 2025 · IPR2024-01462 · APJ Jo-Anne M Kokoski · IPR · Rehearing

  The Board denied Solus’s rehearing request, leaving institution denied for claims 1–8 because the petition did not adequately show motivation to combine Hanafusa and Dobashi.

  RulingsRehearing decision

  • RehearingRehearing, deniedDenied

    “of the decision de novo, but instead review the decision for an abuse of discretion. 37 C.F.R. § 42.71(c). An abuse of discretion may be determined “if a decision is based on an erroneous interpretation of law, if a factual finding is not supported by substantial evidence, or if the decision represents” slip op. at 2

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable

    “In particular, neither Petitioner nor Dr. Josefowicz adequately explain why a POSITA looking for ways to make Hanafusa’s surface roughness low-profile would look to methods to achieve Dobashi’s RSm values. Dobashi teaches that because RSm “can be adopted as the period of waviness, RSm can also be used as an indicator for judgment of the surface.” Ex. 1005, 2:66–3:1, 6:23–26. Dobashi explains that waviness is “an indicator for determining whether the fine pattern forming performance is good or bad,” and “[t]he surface has small waviness and is smooth when RSm is large, and the surface has large waviness Dobashi also teaches that surface roughness Rzjis is used as a low-profile indicator. Ex. 1005, 2:66–3:1. Dobashi, therefore, teaches that RSm is an indicator of surface waviness, which Dobashi explains is different than surface roughness. Id. at 2:66– 3:3, 6:23–29. Given these teachings in Dobashi, neither Petitioner nor Dr. Josefowicz sufficiently explains how or why a POSITA would have been motivated to implement Dobashi’s RSm values to make Hanafusa’s surface roughness low-profile. See Pet. 10–12; Ex. 1003 ¶¶ 46–52.” slip op. at 4

  § 103 obviousness
  Patents in suitUS 11,346,014
• Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing denied
  PTAB · Oct 7, 2025 · IPR2024-01461 · APJ Jo-Anne M Kokoski · IPR · Rehearing

  The Board denied rehearing and left in place its denial of institution because Petitioner did not show that claims 1–10 were likely obvious over the asserted combinations.

  RulingsRehearing decision

  • RehearingRehearing, deniedDenied

    “II. STANDARD OF REVIEW When rehearing a decision on institution, we do not review the merits of the decision de novo, but instead review the decision for an abuse of discretion. 37 C.F.R. § 42.71(c). An abuse of discretion may be determined “if a decision is based on an erroneous interpretation of law, if a factual finding is not supported by substantial evidence, or if the decision represents an unreasonable judgment in weighing relevant factors.” Arnold Partnership v. Dudas, 362 F.3d 1338, 1340 (Fed. Cir. 2004) (citing In re 1 US 2013/0108922 A1, published May 2, 2013 (Ex. 1004, “Shinozaki”). 2 G. Khatibi, Temperature Dependent Elastic and Thermal Properties of Thin Copper Foils, Copper; Proceedings of the International Conference Copper ’06 (2006) (Ex. 1006, “Khatibi”). 3 Korean Patent Pub. No. 10-2012-0003485, published Jan. 10, 2012 (Ex. 1013; Ex. 1014 (English translation), “Toshio”). 4 US 2013/0108887 A1, published May 2, 2013 (Ex. 1012, “Kim”). 5 Griesi, M.B., Characterization of Electrodeposited Copper Foil Surface Roughness for Accurate Conductor Power Loss Modeling (2014) (Master’s Thesis, University of South Carolina) (Ex. 1015, “Griesi”). rehearing has the burden to show that the decision should be modified. 37 C.F.R. § 42.71(d). Additionally, the request for rehearing “must specifically identify all matters the party believes the Board misapprehended or overlooked, and the place where each matter was previously addressed in a motion, an opposition, or a reply.” Id.” slip op. at 2

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Not shown unpatentable

    “For example, Dr. Randall does not provide adequate explanation or objective evidence to support his opinion that Khatibi’s use of a laser speckle based dilatometer instead of the claimed thermomechanical analyzer “is unlikely to significantly impact the CTE[6] value” because “variations in equipment and a heating speed of 5° C/min would not significantly alter the results.” Ex. 1003 ¶ 58. In particular, Dr. Randall neither explains what constitutes a “significant” impact on CTE, nor provides objective evidence to support his contention that equipment variations and heating differences would not “significantly alter” the resulting measurements. And although Dr. Randall opines that “the heating rate (5°C per minute) is typical for certain devices” such as a thermomechanical analyzer or dilatometer, and “[t]ypically, these devices use temperature ramp rates between 2°C and 20°C per minutes, so the ‘5° C./min’ recited in [1d] is common and should not drastically affect the measurement results,” Dr. Randall fails to point us to any evidence showing that these temperatures are “typical” or that the claimed heating rate is “common.” Id. ¶ 59 (emphases added).” slip op. at 4

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable

    “Petitioner, however, does not adequately explain why a POSITA would have been motivated to modify Kim’s copper foil surface to have a Pc value of 19.2 as reported in Griesi. In particular, neither Petitioner nor Dr. Randall points us to, nor do we discern, any teaching in Griesi that a peak count of 19.2 provides any particular benefits or properties that would have lead a POSITA to modify Kim’s copper foil surface as Petitioner proposes. Instead, Petitioner’s arguments that a POSITA would have been motivated to modify Kim’s copper foil surface with Griesi’s peak count patent itself. See KSR Int’l Co. v. Teleflex Inc., 550 U.S. 398, 421 (2007) (stating that the fact finder must be aware “of the distortion caused by hindsight bias and must be cautious of arguments reliant upon ex post reasoning”). It was Petitioner’s burden to establish that the combined teachings Kim and Griesi disclose limitation [1g] as proposed. We are not persuaded that we misapprehended Petitioner’s argument when we determined that Petitioner did not meet that burden.” slip op. at 8

  • BurdenDecided for patent owner

    “It was Petitioner’s burden to establish the Khatibi, alone or in combination with Shinozaki, Toshio, and Kim, discloses limitation [1d]. We concluded that Petitioner failed to meet that burden for the reasons explained in our Decision. We are not persuaded that we overlooked or misapprehended Khatibi’s disclosures, or Petitioner’s evidence and explanation thereof, in doing so.7” slip op. at 5

  § 103 obviousnesscites KSR
  Patents in suitUS 10,811,689
• Shenzhen Kangvape Technology Co., Ltd. v. Rai Strategic Holdings, Inc.Other
  PTAB · Jun 25, 2025 · IPR2024-01406 · APJ Jo-Anne M Kokoski · IPR · Remand

  On remand, the Board denied institution of review of claims 1, 3, 4, 8–13, and 15 under § 314(a), finding the Fintiv factors favored discretionary denial.

  RulingsRemand decision

  • PTAB / AIA Trials › Discretionary denial › Fintiv (parallel litigation)Denied

    “stay or evidence exists that one may be granted if a proceeding is instituted.” Fintiv, Paper 11 at 6. A stay of litigation pending resolution of an inter partes review allays concerns about inefficiency and duplication of efforts, and strongly weighs against exercising our authority to deny institution. Fintiv, Paper 11 at 6. The Guidance Memo states that “the Board will apply the Fintiv factors when there is a parallel proceedings at the International Trade Commission.” Guidance Memo 2. Patent Owner asserts that a stay of the ITC Investigation had not been requested at the time of the Institution Decision,7 and argues that “the ITC does not stay investigations pending IPR.” PO Supp. Br. 4. Patent Owner also notes that the Institution Decision issued “just days before the ITC evidentiary hearing.” Id. Accordingly, Patent Owner argues that this factor favors denial. Id. Patent Owner is likely correct that the ITC would not have been inclined to grant a stay if one had been requested at the time the Institution Decision issued. Moreover, the ITC conducted a full evidentiary hearing less than three weeks after the Institution Decision issued, and the target date for the ITC’s final determination is four months before the statutory deadline for the Board’s final written decision. PO Supp. Br. 5. Accordingly, we” slip op. at 9

  Discretionary denial
  Patents in suitUS 11,925,202
• Shenzhen Tuozhu Technology Co., Ltd. v. Stratasys, Inc.Instituted
  PTAB · Jun 18, 2025 · IPR2025-00321 · APJ Christopher M Kaiser · IPR · Institution

  The Board instituted IPR on claims 1, 2, 5–7, 9, 16, and 17, finding a reasonable likelihood that claim 1 is anticipated by Boyer.

  RulingsInstitution decision

  • PTAB / AIA Trials › Discretionary denial › Fintiv (parallel litigation)Denied

    “approximately two weeks before the statutory deadline for a final written decision, but the most recent median time-to-trial statistics for Judge Gilstrap in the Eastern District of Texas indicate that the actual trial date will likely be in July 2026, which is later than the statutory deadline to issue a final written decision in this proceeding in mid-June 2026. See Ex. 2001, 7 (median time from filing to trial of 23.2 months); Prelim. Resp. 10. Thus, we find this factor is neutral or weighs slightly against discretionary denial.” slip op. at 10

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted

    “At this preliminary stage, we determine whether the information presented shows a reasonable likelihood that Petitioner would prevail in establishing that at least one of the challenged claims would have been unpatentable over the proposed prior art. We analyze the asserted grounds with the above-noted principles in mind.” slip op. at 7

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that one of ordinary skill in the art “would have had (1) at least a bachelor’s degree in Mechanical Engineering, Computer Engineering, Chemical Engineering, Materials Science, or a related field, and (2) at least two years of research or industry experience in 3D printing or materials used for 3D printing.” Pet. 5 (citing Ex. 1003 ¶¶ 14–16). Petitioner also argues that “[a]dditional experience could substitute for a formal degree or formal training (and vice versa).” Id. Patent Owner proposes a slightly different level of skill, arguing that a person of ordinary skill in the art “would have had a bachelor’s degree in Mechanical Engineering, Computer Engineering, Chemical Engineering, Materials Science, or a comparable field and at least two years of experience related to 3D printing, with additional experience potentially being a substitute for a formal degree or training (and vice versa).” Prelim. Resp. 24. Neither party explains why the outcome of this case would be affected by the adoption of any of the proffered definitions of a person of ordinary skill in the art. For purposes of this Decision, we adopt Petitioner’s assessment of the level of ordinary skill in the art, as it appears to be consistent with the ’713 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 16

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction needed

    “We note that, as discussed below, we are able to determine whether to institute inter partes review of the ’713 patent without expressly construing the term “from multiple print heads or deposition lines.” See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))). As for Patent Owner’s argument that Petitioner has failed to carry its burden to identify how the claims are to be construed, we disagree on the present record. Although Petitioner does not provide a preferred construction for the single term it proposes requires construction, Petitioner does identify which of its two alternative constructions applies to each of its asserted grounds of unpatentability. Pet. 6 (“Under the first construction, [the obviousness grounds] are applicable, and [the anticipation ground] would be excluded from the claim scope. Under the alternative construction, all of [the asserted grounds] are applicable.”). In our view, this approach does not fail to satisfy Petitioner’s burden under 37 U.S.C. § 42.104(b)(3).” slip op. at 17

  Claim construction§ 102 anticipationDiscretionary denialcites Phillips
  Patents in suitUS 9,421,713

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.