- Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00187 · APJ Debra L Dennett · IPR · Final written decision
Claims 1–17 are unpatentable under § 103, principally because Chang in view of Jin renders them obvious; the Jin/Feldmann grounds were not shown.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49).” slip op. at 10
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11
- Expert testimonyPatent owner expert creditedDecided for patent owner
“gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard. Without an apparent reason to modify the teachings of Jin and Feldmann to” slip op. at 19
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 17
Patent outcomesUS 10,230,009 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,230,009 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00917 · APJ Debra L Dennett · IPR · Final written decision
Claims 1–17 are unpatentable under § 103 over Chang and Jin, alone or with Seo or Watanabe; the Jin and Feldmann grounds were not shown.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’009 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’009 patent and the prior art.” slip op. at 10
- Expert testimonyPatent owner expert creditedDecided for patent owner
“We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard.” slip op. at 19
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightMotivation not foundNot shown unpatentableNot shown unpatentable
“On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 17
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentableUnpatentable
“Patent Owner focuses on Chang’s description in paragraph 76 of a single configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” Resp. 42 (citing Ex. 1013 ¶ 76). In so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Id. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Chang ¶ 62; Tr. 15:20–17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 73, 217 (citing Ex. 1023 § 1). Chang also discloses that the emitter area may be formed by thermal diffusion, ion implantation or the like. Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding a tunneling layer and a base surface field area from periphery region and isolation region. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” slip op. at 32
Patent outcomesUS 10,230,009 unpatentable§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,230,009 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00006 · APJ Debra L Dennett · IPR · Final written decision
Claims 1–17 are unpatentable under § 103, principally over Chang and Jin; the Board rejected the Jin and Feldmann combinations for lack of a reason to combine.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’009 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’009 patent and the prior art.” slip op. at 10
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 26. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 116 with Pet. 26). Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” See Magnum, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard.” slip op. at 19
- Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable
“configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” Resp. 42 (citing Ex. 1013 ¶ 76). In so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Id. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Chang ¶ 62; Tr. 15:20–17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 73, 217 (citing Ex. 1023 § 1). Chang also discloses that the emitter area may be formed by thermal diffusion, ion implantation or the like. Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding a tunneling layer and a base surface field area from periphery region and isolation region. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” slip op. at 32
Patent outcomesUS 10,230,009 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,230,009 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00007 · APJ Avelyn M Ross · IPR · Final written decision
Claims 1–11 are unpatentable under §103 over Chang and Jin because the combination teaches the claimed isolation portion and the claimed tapering.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedOther
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightTeaching away not foundNot shown unpatentable
“On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16
- Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner
“However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide.” slip op. at 18
Patent outcomesUS 9,722,104 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,722,104 - Bio-Rad Laboratories, Inc. v. California Institute Of TechnologyNo claims unpatentablePTAB · Mar 23, 2026 · IPR2024-01451 · APJ Tawen Chang · IPR · Final written decision
Claims 1–19 were not shown unpatentable: Larson did not establish the claimed detection in a single sample volume, and the asserted obviousness combinations did not cure the deficiencies.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Patent Owner states that, “[f]or purposes of this IPR proceeding, PO does not contest Petitioner’s description of qualifications for a person of ordinary skill in the art (POSA) set forth [above].” PO Resp. 23. In view of the above, and because Petitioner’s uncontested description of one of ordinary skill in the art is reasonable and consistent with the ’921 patent and the cited art, we adopt Petitioner’s definition of a POSA for purposes of this Decision, except that we replace the phrase “at least a year of experience in quantitative and/or dPCR and fluorescence-based analyte detection” with “around a year of experience in quantitative and/or dPCR and fluorescence-based analyte detection.” Pet. 9 (emphasis added).13” slip op. at 14
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner
“We begin with “the context in which a term is used in the asserted claim,” which can be “highly instructive.” Phillips, 415 F.3d at 1314. In this case, claim 1 recites that the claimed assay is “capable of unambiguously detecting the presence or absence of each of said at least M analytes, in any combination of presence or absence, in a single sample volume, . . . wherein the analytes are amplified in the single sample 15 In this regard, we note that Petitioner’s claim construction position is not predicated on the collection of droplets being reconstituted into its original, pre-partition form prior to amplification; rather, the droplets remain compartmentalized from each other in the PCR thermal cycling tube. Tr. 65:21–66:9 (Petitioner’s counsel explaining that the droplets do not combine in the PCR thermal cycling tube but, rather, are “suspended in an immiscible fluid and analyzed en masse”). indicates that the first instance of single sample volume, i.e., the single sample volume in which the presence or absence of each M analytes are to be detected, is the antecedent basis for the second instance of “single sample volume,” i.e., the single sample volume in which the analytes are amplified. Thus, as the parties appear to agree, the single sample volume in which amplification takes places must be the same single sample volume in which the presence or absence of analytes are to be detected. We are not persuaded that, when accorded its plain and ordinary meaning, a single sample volume divided into a collection of droplets would be considered the “same” single sample volume prior to its partition.” slip op. at 17
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable
“With respect to the limitation, “wherein the analytes are amplified in the single sample volume,” Petitioner asserts that “Larson discloses PCR assays that amplify target polynucleotide in a single sample volume, specifically a portion of the reaction mixture that is subsequently partitioned into droplets.” Pet. 31 (emphasis added). There is no dispute that the amplification of the analytes in Larson occurs in the droplets. Larson ¶¶ 6–7 (explaining that “[d]igital PCR (dPCR) is an alternative quantitation method in which dilute sample are divided into many separate reactions” and that “[t]he template is amplified in the droplet for detection”) (emphasis added). Because the claims require that amplification of the analytes be in the same sample volume in which the at least M analytes, in any combination of presence or absence, is unambiguously detected, and because the pre-partition single sample volume is not the same single sample volume as the collection of droplets after partition under our claim construction set forth above, we find Petitioner has not shown, by a preponderance of evidence, that claims 1–10 and 13–19 are anticipated by Larson.17 Tr. 68:12–69:14 (Petitioner’s counsel” slip op. at 27
- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable
“Although we agree with Petitioner that Larson contemplates scenarios in which droplets may contain more than one target molecule and does not require the exclusion of such multiple occupancy droplets in all embodiments, we are nevertheless not persuaded Petitioner has shown, based on a preponderance of evidence, that Larson renders obvious an assay capable of unambiguously detecting, in such multiple occupancy droplets, the presence or absence of each of at least M analytes, in any combination of presence or absence, when M is greater than F and F is at least 2.” slip op. at 32
Patent outcomesUS 11,827,921 not shown unpatentableClaim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,827,921 - Kohler Co. v. Delta Faucet Co.All claims unpatentablePTAB · Feb 18, 2026 · IPR2024-00700 · APJ Jane E Inglese · IPR · Remand
On remand, the Board held claims 1–24 unpatentable as obvious over the asserted prior-art grounds, including Tseng’s disclosure of side-emitted light under the Director’s construction.
RulingsRemand decision- RemandOther
“We have jurisdiction under 35 U.S.C. § 6. This Final Written Decision on Remand from Director Review is entered pursuant to 35 U.S.C. § 318(a). Having reviewed the complete trial record pursuant to the Director Review Order, we determine that Petitioner has shown, by a preponderance of the evidence, that the challenged claims are unpatentable.” slip op. at 3
- Skill levelSkill level petitioner adoptedDecided for petitioner
“For purposes of this Decision, we adopt Petitioner’s definition of a POSITA. Petitioner’s witness (Mr. Cook) qualifies as a POSITA under this definition, and, therefore, is qualified to opine from the perspective of a POSITA on technical matters included within the areas of expertise prescribed by the definition. As indicated above, Petitioner’s definition of a POSITA does not require education in the field of optics and professional experience designing or analyzing optical apparatus, unlike Patent Owner’s definition. We are aware, however, that Patent Owner’s witness (Dr. Klopp) has more extensive experience with optical systems and methods than Petitioner’s witness (Mr. Cook). Compare Ex 1003 ¶¶ 8–14, Ex. 2005, 39:21–59:17, with Ex. 2003 ¶¶ 3–20, Ex. 2004, 1–2, Ex. 1015, 10:22–13:25. Although Mr. Cook possesses excellent credentials in the field of mechanical engineering, his experience in the design and analysis of optical systems and methods is sparse and insubstantial compared to that of Dr. Klopp. Id. Due to this difference in experience levels, in instances where the witnesses express differing views on factual issues related to optical systems and methods, we accord more weight to Dr. Klopp’s testimony than to Mr. Cook’s.” slip op. at 9
- Expert testimonyPatent owner expert creditedDecided for patent owner
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner
“The Director’s Order instructs us to adopt its interpretation of the recitation in claim 10 of “an outer illumination surface extending perpendicular to the longitudinal axis of the housing” (“the disputed limitation”) as being “satisfied by any amount of light emitted from the side surface.” Order 3. We, accordingly, construe the disputed limitation of claim 10 as a surface extending perpendicular to the longitudinal axis of the housing through which any amount of light is emitted from the side surface.” slip op. at 10
Patent outcomesUS 10,393,363 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,393,363 - Samsung Display Co., Ltd. v. Pictiva Displays International Ltd.Some claims unpatentablePTAB · Jan 22, 2026 · IPR2024-01094 · APJ Grace Karaffa Obermann · IPR · Final written decision
Claims 1, 2, 6, and 8–14 are unpatentable as obvious over Ma; claims 3 and 4 were not shown unpatentable over Werner.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends: A person of ordinary skill in the art (“POSA”) at the time of the alleged invention of the ’223 patent would have had a university degree in chemistry and additional expertise or a second university degree in the field of electrical engineering, particularly optoelectronics, or alternatively a university degree in electrical engineering and additional expertise or a second university degree in the field of chemistry. The person of ordinary skill in the art has spent several years studying the structure and function of organic optoelectronic components, in particular OLEDs, and has detailed knowledge of the chemical structure of light-emitting organic layers and the transport of charge carriers to these layers. In this respect, the person of ordinary skill in the art works at the interface between electrical engineering/physics (charge carrier transport and light emission processes in optoelectronic components) and chemistry, in particular organic chemistry (materials and layer stack combinations suitable). Pet. 14 (citing Ex. 1003 ¶¶ 46–47). Patent Owner does not dispute Petitioner’s contention. See generally Resp. Neither party indicates that the result would change depending on the definition selected. We adopt Petitioner’s uncontested proposed definition, because it is consistent with the disclosures of the asserted prior art references. See Ex. 1005, (code 57); Ex. 1007, 8107 (abstracts of the references asserted in the patentability challenges).” slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“history pertaining to the patent.” 37 C.F.R. § 42.100(b). Under that standard, claim terms generally are given their plain and ordinary meaning as would have been understood by the ordinarily skilled artisan at the time of the invention and within the context of the entire patent disclosure. See Phillips v. AWH Corp., 415 F.3d 1303, 1313 (Fed. Cir. 2005) (en banc). We construe claim terms only as relevant to the parties’ contentions and only to the extent necessary to resolve the issues in dispute. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999); Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017). Neither party indicates that an express construction for any claim term is necessary to resolve the disputes at hand. Pet. 15; see generally Resp. On this record, we determine that no claim term requires express construction for purposes of this Decision. In our analysis of the challenges, however, we discuss the meaning of the terms “metal complex” and “central metal atom,” which appear in claim 1 (Ex. 1001, 19:19–20) to the extent necessary to resolve Patent Owner’s contention that Petitioner fails to establish that Ma invalidates claim 1. See Resp. 53, 56–58.” slip op. at 9
- Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication establishedDecided for petitioner
“Whether Ma qualifies as a “printed publication” involves an inquiry into the facts and circumstances surrounding the reference’s disclosure to members of the public. In re Klopfenstein, 380 F.3d 1345, 1350 (Fed. Cir. 2004). A reference is considered “publicly accessible” upon a satisfactory showing that the document has been “disseminated or otherwise made available to the extent that persons interested and ordinarily skilled in the subject matter or art exercising reasonable diligence[] can locate it.” Kyocera Wireless Corp. v. ITC, 545 F.3d 1340, 1350 (Fed. Cir. 2008); see Hulu, LLC v. Sound View Innovations, LLC, IPR2018-01039, Paper 29, 10– 11 (PTAB Dec. 20, 2019) (precedential).” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentable
“Based on the information presented, we find Petitioner has the better position. Patent Owner admits that joint vaporization means “two materials vaporize together.” Reply 21 (quoting Resp. 54). As Petitioner argues, “This is what Ma discloses.” Id. We agree with Petitioner that Ma describes a “two-component” electron transport layer having a “thickness with one value.” Id.; see Ex. 1007, 811 (reporting a “co-deposited” application of “BPhen:LiQ” that is “50 nm thick”). Ma’s disclosure, thereby, strongly “indicates that the two components were vaporized together––as opposed to creating a ‘macroscopically homogenous form’” prepared by sequentially vaporizing the individual components as Patent Owner “hypothesizes.” Reply 21 (citing Ex. 1020 ¶¶ 42–44; Ex. 2041 ¶¶ 155–157); see Resp. 54– 55; see also Ex. 1007, 811 (Ma’s description of its device fabrication, appearing in the third paragraph of the experiments section). Petitioner further advances evidence that “[p]reparing a layer that is ‘macroscopically homogeneous’ but potentially microscopically heterogeneous,” as Patent Owner postulates, “would introduce excessive variability and render the data noncomparable and unreliable, thus undermining the experiment’s purpose.” Reply 21 (citing Ex. 1020 ¶ 44); see Resp. 54–55. Patent Owner presents no counterargument or evidence that is persuasive to undercut Petitioner’s reasoning or evidence on that point. See Sur-reply 19–22. Petitioner also argues that an ordinarily skilled artisan would have recognized “that vaporizing materials together would best achieve Ma’s objective of assessing the current density using different Liq doping percentages.” Reply 22 (citing Ex. 1007, 811; Ex. 1020 ¶ 51). Here again, Petitioner’s evidence on point stands uncontested. See Sur-reply 19–22 (declining to contest that point). On this record, therefore, we agree with Petitioner that, as to the relevant disclosure in Ma, “the most natural interpretation of ‘co-deposition’ for forming a layer, particularly when there is nothing to indicate that the materials” are “vaporized sequentially,” is that the materials are co-deposited by joint vaporization. Reply 22 (citing Ex. 1020 ¶ 46–51). We further agree that, “[u]nder a preponderance standard, Ma’s disclosures are sufficient to render joint vaporization at least obvious.” Id. For the above reasons, we determine that Petitioner demonstrates by a preponderance of the evidence that Ma discloses joint vaporization as required by the challenged claims.” slip op. at 15
Patent outcomesUS 8,558,223 mixedClaim construction§ 102 anticipation§ 103 obviousnesscites Phillips · GrahamPatents in suitUS 8,558,223 - Sigray, Inc. v. Carl Zeiss X-Ray Microscopy, Inc.All claims unpatentablePTAB · Dec 12, 2025 · IPR2022-00218 · APJ Grace Karaffa Obermann · IPR · Remand
On remand, claims 2, 5, and 6 were held unpatentable as obvious; the motion to amend was denied for proposed claims 16–21 and dismissed for claims 22–23.
RulingsRemand decision- Skill levelSkill level patent owner adoptedDecided for patent owner
“The level of ordinary skill in the art, as articulated by Patent Owner, more accurately reflects the subject matter of the ’704 Patent and the asserted prior art than does Petitioner’s articulation. Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (“the prior art itself reflects an appropriate level” as evidence of the ordinary level of skill in the art) (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163 (Fed. Cir. 1985)). Petitioner does not explain how “control theory” and “applied mathematics” (Pet. 16) relate to the subject matter of the ’704 Patent or the asserted prior art, and Petitioner’s reference to “laboratory experience” (id.) is too general to be useful in defining the level of skill. Furthermore, whereas Petitioner requires a POSITA to have “x-ray and computing imaging experience” (id.), Patent Owner more particularly specifies “x-ray microtomography experience” (PO Resp. 5), which is the field of art for the ’704 Patent, as well as many of the asserted prior art references. Ex. 1001, code (54) (“High resolution direct-projection type x-ray microtomography system using synchrotron or laboratory-based x-ray source”); Ex. 1007 (discussing X-ray microcomputed tomography); Ex. 1008 (discussing X-ray nanotomography and microtomography); Ex. 1010, code (54) (“Method and apparatus for utilizing an electro-optic detector in a microtomography system”); Ex. 1011 (title: “Three- Dimensional X-ray Microtomography”). For those reasons, we apply Patent Owner’s definition of a POSITA.” slip op. at 8
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for patent owner
“Neither party proposes any express claim constructions. See Pet. 17 (“all claim terms should receive their plain and ordinary meaning”); PO Resp. 5 (applying the same constructions as Petitioner). In accordance with the Federal Circuit’s mandate, however, we adopt and apply herein “[t]he plain meaning of the term ‘between 1 and 10,’” which “includes tiny, and even undetectable, magnification” and, moreover, we take account that Jorgensen anticipates claim 1, including that limitation. Paper 38, 11–12. We determine that no other claim term requires express construction for purposes of resolving any controversy between the parties. Realtime Data LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 10
- Obviousness (§103) › KSR rationalesUnpatentableUnpatentable
“i. Spot Size as a Result-Effective Variable First, Patent Owner argues that Petitioner fails to “identify any prior art that discloses an x-ray source having the claimed spot size.” PO Resp. 45. We agree with Petitioner, however, that Patent Owner “fails to consider the advantages of a smaller spot size” –– advantages that would have been known to a POSITA, given that they are discussed “in each of these references.” Reply 19. Petitioner further directs us to evidence that Patent Owner’s own witness, Dr. Bentley, “agreed that a POSITA would have been aware of tradeoffs between smaller and larger spot sizes.” Id. (citing Ex. 1024, 45:14–47:20). In other words, the evidence supports that spot size would have been a result effective variable and, on this record, that optimizing that variable in view of various “tradeoffs,” recognized by Patent Owner’s own witness, would have been within the level of ordinary skill in the art. Id.; see In re Boesch, 617 F.2d 272, 276 (CCPA 1980) (“discovery of an optimum value of a result effective variable in a known process is ordinarily within the skill of the art”). Patent Owner does not counter Petitioner’s evidence on that point, but instead, refers us back to a related argument in the Response, pertaining to whether one would have undertaken that modification with a reasonable expectation of success, which we address below in connection with Patent Owner’s third argument. Sur-reply 18 (citing PO Resp. 47–49).” slip op. at 12
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner
“smaller spot sizes.” PO Resp. 45. We recognize that an obviousness challenge may be overcome “by showing that the prior art teaches away from the claimed invention in any material respect.” In re Peterson, 315 F.3d 1325, 1331 (Fed. Cir. 2003) (citing In re Geisler, 116 F.3d 1465, 1469 (Fed. Cir. 1997)). For a reference to teach away, however, it must state more than a general preference for an alternative invention. Specifically, it must “criticize, discredit, or otherwise discourage” investigation into the invention claimed. DePuy Spine, Inc. v. Medtronic Sofamor Danek, Inc., 567 F.3d 1314, 1327 (quoting In re Fulton, 391 F.3d 1195, 1201 (Fed. Cir. 2004)). In Patent Owner’s view, “Jorgensen teaches away from smaller spot sizes” because smaller spot sizes “require significantly more power to generate the desired flux.” PO Resp. 45. Patent Owner directs us to evidence that, at best, illustrates that this disadvantage would have been among the “tradeoffs between smaller and larger spot sizes” that inform the selection. Ex. 1024, 45:14–47:20 (Dr. Bentley’s cross-examination testimony); see PO Resp. 45–46 (evidence of proposed disadvantage). This evidence does not “criticize, discredit, or otherwise discourage” investigation into the invention claimed. Fulton, 391 F.3d at 1201. At best, we find that it may indicate a preference for a different spot size depending on the desired application.” slip op. at 13
Patent outcomesUS 7,400,704 unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 7,400,704 - PTAB · Nov 6, 2025 · PGR2025-00040 · APJ Kimberly Mcgraw · PGR · Institution
The Board instituted PGR on claims 1–9, 11–33, and 35–38 on all petition grounds, finding it more likely than not that Hassfjell-Hoff anticipates at least claim 1.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“Under 35 U.S.C. § 324(a), a post-grant review may be instituted only if “the information presented in the petition . . . demonstrate[s] that it is more likely than not that at least 1 of the claims challenged in the petition is unpatentable.” Post-grant review is available for patents that issue from applications that at one point contained at least one claim with an effective filing date on or after March 16, 2013. See Leahy-Smith America Invents Act, Pub. L. No. 112-29, 125 Stat. 284 (2011) (“AIA”), §§ 3(n)(1), 6(f)(2)(A). After considering the briefing and the evidence of record, for the reasons set forth below, we determine that Petitioner has shown that the ’437 patent is eligible for post-grant review and that it is more likely than not that at least one challenged claim of the ’437 patent is unpatentable under § 324(a). Accordingly, we institute a post-grant review of all challenged claims of the ’437 patent.” slip op. at 2
- Adverse judgmentAdverse judgmentOther
“Here, Patentee Sciencons AS filed a statutory disclaimer of claims 10 and 34 of the ’437 patent. Ex. 2001; Prelim. Resp. 43. Based on our review of Exhibit 2001 and the Office’s public records, we find that the disclaimer of claims 10 and 34 complies with the above-listed requirements of 37 C.F.R. § 1.321(a). Accordingly, we treat claims 10 and 34 as having never been part of the ’437 patent. See Vectra Fitness, Inc. v. TNWK Corp., 162 F.3d 1379, 1383 (Fed. Cir. 1998) (“This court has interpreted the term ‘considered as part of the original patent’ in [35 U.S.C.] § 253 to mean that the patent is treated as though the disclaimed claims never existed.”). Because post-grant review cannot be instituted based on disclaimed claims, claims 10 and 34 are outside the scope of this proceeding. 37 C.F.R. § 42.207(e) (“No post-grant review will be instituted based on disclaimed claims.”); General Elec. Co. v. United Techs. Corp., IPR2017-00491, Paper 9 (PTAB July 6, 2017) (precedential) (denying institution in view of a statutory disclaimer of all the challenged claims). Thus, we confine our analysis in this Decision to claims 1–9, 11–33, and 35– 38, the remaining challenged claims that have not been disclaimed.” slip op. at 6
- PTAB / AIA Trials › Real party in interest / privityGranted
“Sciencons AS also states that ARTBIO, Inc. is responsible for defending the ’437 patent in this proceeding and requests that ARTBIO, Inc. be included in the caption for this proceeding.2 Paper 4, 1. ARTBIO, Inc. has signed powers of attorney appointing the same practitioners that were appointed by Sciencons AS to transact all business associated with the instant post-grant review review of the ’437 patent. See Paper 3. To date, no objection has been raised to Patent Owner’s request. Given Sciencons AS’s representation that ARTBIO, Inc. is currently the exclusive licensee of the ’437 patent and is responsible for defending the ’437 patent, we grant Sciencons AS’s unopposed request that ARTBIO, Inc. be included in the caption. For convenience we refer to Sciencons AS and the purported exclusive licensee ARTBIO, Inc. collectively as “Patent Owner.” As stated supra, to the extent any party disputes ARTBIO, Inc.’s right to participate in this proceeding or to be included in the caption, the party shall request authorization to brief the issue within 10 business days of this Decision.” slip op. at 3
- Skill levelSkill level petitioner adoptedDecided for petitioner
“nuclear chemistry, radiochemistry, or materials science, or a comparable field of study, plus approximately two to three years of professional experience with radioisotope generators, radiopharmaceutical chemistry, nuclear medicine, or other relevant industry experience” and that “[a]dditional graduate education could substitute for professional experience, and significant experience in the field could substitute for formal education.” Pet. 2–3 (citing Ex. 1002 ¶ 33; Ex. 1019 ¶ 27). At this stage of the proceeding, Patent Owner does not dispute Petitioner’s proposed definition nor provide a proposed definition of its own. See generally Prelim. Resp. For the purposes of this Decision, we adopt Petitioner’s undisputed proposed definition of a POSITA.” slip op. at 10
Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites PhillipsPatents in suitUS 12,249,437 - PTAB · Oct 29, 2025 · IPR2025-00918 · APJ Avelyn M Ross · IPR · Institution
The Board instituted inter partes review of claims 1–11 on all asserted grounds and granted Canadian Solar’s motion for joinder in IPR2025-00007.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“We instituted review of claims 1–11 of the ’104 patent in IPR2025-00007 after a review of all arguments and evidence presented by the parties, including Patent Owner’s arguments in its preliminary response. For the reasons discussed in the Institution Decision in IPR2025-00007, we determine that Petitioner demonstrates a reasonable likelihood of showing at least one claim of the ’104 patent is unpatentable. Thus, we find that the Petition warrants institution of inter partes review on all claims and grounds set forth in the Petition.” slip op. at 11
- PTAB / AIA Trials › Joinder §315(c) / SAS all-or-nothingJoinder, grantedGranted
“Patent Owner did not file an opposition to Petitioner’s Motion for Joinder. Upon consideration of Petitioner’s arguments, we are persuaded that it is appropriate under these circumstances to join Petitioner to the proceeding in IPR2025-00007. Petitioner’s agreement to accept an “understudy” role and to not actively participate in IPR2025-00007 unless the current petitioner ceases to participate will limit any potential impact on the trial schedule and will avoid increasing the costs or complexity of the proceeding. Therefore, joinder of 8 Available at https://www.uspto.gov/TrialPracticeGuideConsolidated. Petitioner to IPR2025-00007 will further the goals of a just, speedy, and inexpensive resolution of Petitioner’s challenge. 37 C.F.R. § 42.1(b).” slip op. at 12
- Skill levelSkill level petitioner adoptedDecided for petitioner
“In light of the record before us, and for purposes of this Decision, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art. We will make any final determination pertaining to the level of ordinary skill in the art, however, on the full trial record.” slip op. at 10
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11
Claim constructioncites Phillips · KSR · GrahamPatents in suitUS 9,722,104
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.