- PTAB · Oct 6, 2026 · IPR2025-00530 · APJ Scott C Moore · IPR · Final written decision
Original claims 1–9 were canceled; the non-contingent motion to add substitute claims 10–18 was denied for lack of written-description support, and claim 18 was also indefinite.
RulingsFinal written decision- 112 supportMotion to amend, deniedDenied
“that either the ’303 application or the ’838 provisional contain adequate written description support for the disputed feature of limitation [10.d]. Though the disclosures cited by Patent Owner indicate that a secondary identifier can be used to aid in verification of a UAV, these disclosures also make clear that both first and second identifiers are transmitted by and received from the UAV. See, e.g., Ex. 2002, 4:15–17, 30:24–31:6; Ex. 2003 ¶¶ 14, 66. Patent Owner’s reliance on disclosure characterized as transmitting an identifier from a remote computing system “through the UAV” (Reply 2) is not persuasive. The cited disclosures from the ’303 application and ’838 provisional generally disclose that the identifiers transmitted by a UAV can be “generated remotely,” such as by a “remote computing system.” Ex. 2002, 14:23–15:2; Ex. 2003 ¶ 45. But Patent Owner has not identified disclosure indicating that a remote computing system may transmit an identifier to the identification receiver. In the ’303 application and ’838 provisional, only the UAV (which is part of the discrimination system, and thus not “remote”) actually transmits identifiers to the identification receiver. Patent Owner is correct in its assertion that an “aerial system identifier can be generated on-board the aerial system” or “generated remotely . . . at a remote computing system.” Mot. 7 (citing Ex. 2002, 14:23–15:2; Ex. 2003 ¶ 45). But even if a UAV’s identifier was at some time in the past generated by a remote computing system, the subsequent transmission of that identifier from the UAV to the identification receiver would not satisfy the plain language of limitation [10.d]. The claim language “receive … a second identifier from a computing system that is remote to the discrimination system” requires the receipt of a transmission of the second identifier from a remote computing system. This claim language limits the source of the received transmission (i.e., where the particular transmission is “receive[d] … from”). Thus, the relevant issue is from where was the recited second identifier received. The relevant is not where the second identifier was originally generated.” slip op. at 12
- Disclosure Requirements (§112) › Definiteness (Nautilus)DefiniteIndefiniteMixed
“We determine that the disputed language in limitation [10.d] is not indefinite. There is no recitation in proposed substitute claim 10 that the second identifier is transmitted solely from the identifier transmission system. Thus, the alleged irreconcilable contradiction cited by Petitioner is not recited in the claims. Petitioner’s position appears to rest on the fact that the ’303 application and ’838 provisional do not disclose receiving the second identifier from a remote computing system. See Sur-reply 6 (“To manufacture written description support, [Patent Owner] argues the claim encompasses identifiers routed ‘through the UAV.’”). Though we agree that limitation [10.d] lacks adequate written description support, this defect does not render the claim indefinite because the scope of limitation [10.d] is otherwise reasonably certain based on its plain language. See supra § III.C.4.” slip op. at 18
- Novelty / Anticipation (§102) › Priority / effective filing date / continuation supportReference not prior artPriority date, deniedDecided for patent owner
“In contrast, the ’393 provisional never discloses that the described drone defense system may use the identity of a detected drone to develop a particular countermeasure. The disclosed RTSS certainly uses identity information to determine whether a drone is a threat. And if a threat is identified, the RTSS immediately starts “a series of processes … to determine what rule of engagement will be applied on the intruding drone.” Ex. 1006 ¶ 10. The ’393 provisional discloses that the system may select a particular countermeasure based on (i) the particular zone within a protected area within which a drone is located, (ii) “the behavior of the hostile drone,” or (iii) “other instructions.” Id. ¶¶ 9, 10. But the ’393 provisional never discloses that these “other instructions” may include the identity of the drone. The system disclosed in the ’393 provisional uses the identity of a drone to determine whether to activate the countermeasure system. See id. ¶¶ 16–18. But there is no disclosure in the ’393 provisional that the countermeasure system, once activated, uses the identity of the drone to develop the particular countermeasure to be employed. See generally Ex. 1006. Thus, though the Whitmarsh reference itself contains ample written description support for limitation [19e], the earlier-filed ’393 provisional does not. On this record, and having reviewed the ’393 provisional in its entirety, we determine that the ’393 provisional does not “reasonably convey[] to those skilled in the art that the inventor had possession of” the subject matter of limitation [19e] of Whitmarsh’s claim 19 “as of the filing date” of the ’393 provisional. See Ariad, 598 F.3d at 1351.” slip op. at 27
§ 102 anticipation§ 112 disclosurecites NautilusPatents in suitUS 10,249,199 - PTAB · Oct 6, 2026 · IPR2025-00525 · APJ Scott C Moore · IPR · Final written decision
Original claim 21 was canceled; the Board denied substitute claim 22 for new matter and held it obvious under §103 based on six combinations.
RulingsFinal written decision- 112 supportMotion to amend, deniedDenied
“First, Patent Owner has not shown possession of the disputed feature of a “radio communication module [that] is configured to utilize a secure identifier, the secure identifier comprising a specified excitation.” In the ’406 application, the term “excitation” is used exclusively to refer to a light beam signal. See Ex. 2015, 7:8–13, 9:8–10, 23:9.2 The ’406 application discloses that an identification box on an aircraft may include both an RF module and a separate light sensor. See Ex. 2015, 7:3–11. But nowhere does the ’406 application describe receiving a light beam (e.g., an excitation) with the RF module of the identification box (as opposed to the light sensor), so as to provide support for proposed substitute claim 22’s recitation of a “radio communication module” configured to utilize “a secure identifier . . . comprising a specified excitation.” We disagree with Patent Owner that it suffices that one of ordinary skill in the art “would recognize that these disclosures are equally applicable to the RF-only embodiments” (Reply 5). “It is not sufficient for purposes of the written description requirement . . . that the disclosure, when combined with the knowledge in the art, would lead one to speculate as to modifications that the inventor might have envisioned, but failed to disclose.” Lockwood v. Am. Airlines, Inc., 107 F.3d 1565, 1572 (Fed. Cir. 1997). On this record, and having reviewed the ’959 Patent, the ’153 provisional, and the ’406 application, we find no evidence in those documents that the named inventor was in possession of the concept of a radio communications module “configured to utilize a secure identifier” where “the secure identifier compris[es] a specified excitation.” Second, setting aside the “radio communication module” in proposed substitute claim 22, Patent Owner also has not shown that the named inventor was in possession of the feature of a “secure identifier comprising a specified excitation.” Patent Owner’s argument that the ’406 application describes a light beam directed to a particular aircraft (see Reply 4–5) is 2 The same is true of the ’153 provisional. See Ex. 2016 ¶¶ 29, 34. unavailing. The fact that the properties of a particular light beam indicate that the light beam is intended for a particular aircraft does not demonstrate that the light beam is a “secure identifier,” as we have construed that term. Patent Owner has not identified any disclosure in the ’406 application of a “secure identifier” comprising a light beam, let alone that such light beam can be utilized by a “radio communication module.” The only references to “secure” identifiers in the ’406 application describe radio frequency signals. See Ex. 2015, 2:4–6, 15:21–17:12.3 Having reviewed the ’959 Patent, the ’153 provisional, and the ’406 application, we find no evidence in those documents that the named inventor was in possession of the concept of a “secure identifier comprising a specified excitation.”” slip op. at 15
- ScopeDecided for patent owner
“not impermissibly broaden the scope of the claims of the ’959 Patent. As Patent Owner suggests, there were no limitations in original claim 21 on the type of radio signal the radio communication module could receive, and so it follows that proposed substitute claim 22 does not now encompass receiving a broader set of radio signals. We see no basis for Petitioner’s argument that the past tense verb “received” limited original claim 21 to “signals of a compatible ‘type’ and ‘range.’” Opp. 7. Moreover, the claim language (with the proposed deletion shown double brackets) provides that “the radio communication module is configured to receive a [[received]] radio signal.” Any radio signal that the radio communications module receives would necessarily be a “received” radio signal. Thus, deleting the redundant word “received” does not enlarge the scope of this claim limitation. We also are not persuaded by Petitioner’s suggestion that removing the term “received” broadens original claim 21 by deleting a requirement that the radio signal have already been previously received by the claimed device. See Sur-reply 9. Original claim 21 simply recited, using redundant language, that “the radio communication module is configured to receive a received radio signal.” Ex. 1001, 18:5–7. The most natural reading of this language is that the phrase “received radio signal” is just a description of a radio signal that is received by the recited radio communications module. Petitioner has cited no persuasive evidence that one of ordinary skill in the art would have counterintuitively interpreted this language to impose an additional requirement that the “received radio signal” must have been received twice—a first time by some other component of the device, and a second time by the recited radio communication module. Accordingly, we determine that the proposed amendment does not improperly broaden claim scope.” slip op. at 10
- Disclosure Requirements (§112) › Definiteness (Nautilus)IndefiniteNot shown unpatentable
“572 U.S. 898 (2014). See Memorandum: Approach to Indefiniteness Under 35 U.S.C. § 112 in AIA Post-Grant Proceedings (Jan. 6, 2021).4 Under Nautilus, a claim is indefinite if fails to “inform those skilled in the art about the scope of the invention with reasonable certainty.” 572 U.S. at 910. We agree with Patent Owner that neither of the identified terms are indefinite. Regarding the term “low-altitude aircraft,” we determine the Specification provides a sufficient basis for understanding the scope and meaning of this term with reasonable certainty. The U.S. Court of Appeals for Federal Circuit has explained that, when a term of degree is recited in a claim, it is necessary “to determine whether the patent’s specification provides some standard for measuring that degree.” See Seattle Box Co. v. Indus. Crating & Packing, Inc., 731 F.2d 818, 826 (Fed. Cir. 1984); see also Datamize, LLC v. Plumtree Software, Inc., 417 F.3d 1342, 1350 (Fed. Cir. 2005) (“Some objective standard must be provided in order to allow the public to determine the scope of the claimed invention.”). Here, the Specification describes the related art as including “small UASs (e.g., aircrafts up to 25 pounds flying up to 500 ft of the low altitude airspace).” Ex. 1001, 1:50–52. One of ordinary skill in the art would understand from the Specification that the cited disclosure provides an objective standard for determining the scope of a low-altitude aircraft as one that is designed to fly up to a maximum altitude of about 500 feet.” slip op. at 20
- Skill levelSkill level petitioner adoptedDecided for petitioner
“In our Institution Decision, we adopted Petitioner’s proposal that one of ordinary skill in the art would have had the following qualifications: [E]ither (1) a Bachelor of Science in Mechanical Engineering, Electrical Engineering, Aerospace engineering, or an equivalent field, as well as at least 2 years of academic or industry experience in the aerospace, avionics, telecommunications, or electronic device manufacturing industry, or (2) at least four years of industry experience in any of the above industries. Paper 13, 5 (citing Pet. 21). Patent Owner has not disputed this formulation; thus, we adopt it for purposes of this Decision. See Paper 13, 10–11 n. 8.” slip op. at 23
§ 103 obviousness§ 112 disclosurecites Graham · NautilusPatents in suitUS 10,713,959 - PTAB · May 24, 2024 · IPR2023-00861 · APJ Christopher M Kaiser · IPR · Remand
The Board denied institution because Petitioner did not show a reasonable likelihood that any challenged claim was unpatentable under any asserted ground.
RulingsRemand decision- RemandOther
“Accordingly, the Director instructed us to “determine whether Petitioner has demonstrated that Figure 1 of Godefroy ‘is clear on its face’ or would have reasonably suggested the placement of Godefroy’s sacrificial anode ‘within 10 inches’ of the hot liquid inlet.” Id. at 9. “In making this determination,” the Director instructed us to “consider whether the expert testimony provides sufficient ‘technical detail, explanation, or statements supporting why the expert determines that the feature in question was required or would have been obvious based on the prior art disclosure.’” Id. In addition, although the Director’s decision “is limited to [our] application of Hockerson to the grounds in the Petition involving Godefroy,” the Director instructed us also to “consider what effect, if any, this decision has on the other asserted grounds.” Id. Finally, the Director instructed us to “set forth [our] interpretation” of “the limitation ‘within 10 inches of a hot liquid inlet to the radiator.’” Id. at 8 n.4.” slip op. at 4
- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied
“original decision, the Director’s decision, and the evidence currently of record, we determine that Petitioner has not shown a reasonable likelihood that it will prevail in showing that at least one of the challenged claims is unpatentable. Accordingly, we do not institute an inter partes review of any challenged claim based on any ground asserted in the Petition. IV. ORDER For the reasons given, it is: ORDERED that, pursuant to 35 U.S.C. § 314, the Petition is denied, and no inter partes review is instituted.” slip op. at 19
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner
“evidence. The challenged claims require that a sacrificial anode be placed within a certain distance—10 inches—of the hot liquid inlet, and, because the inlet has some non-zero size, it might be possible for an anode to be within that distance from some parts, but not from all parts, of the inlet. Accordingly, specifying the center axis of the inlet as the point from which to measure the distance to the anode improves on the plain words of the claim in terms of achieving the claim’s objective of placing the anode within a specified distance of the inlet. Moreover, when discussing the distance from the inlet to the anode, the specification of the ’494 patent uses the language “within 10 inches in any direction of the center axis of the inlet connection.” Ex. 1001, 7:61–64. Thus, the intrinsic evidence supports adopting Petitioner’s claim construction. Petitioner’s declarant, Dr. Medlin, relies on Petitioner’s proposed construction. See, e.g., Ex. 1004 ¶¶ 20 (noting that the construction “within 10 inches of the center axis of [a] hot liquid inlet” “ha[s] been adopted by Petitioner”), 96 (“the sacrificial anodes contained in each of the turbulators 2 would be placed within 10 inches of a center axis of a hot liquid inlet to the radiator of Tomosada”), 144 (“A POSITA would understand from Figure 1 that the sacrificial anode 14 is within 10 inches of a center axis of a hot liquid inlet”), 267 (“These teachings would further motivate a POSITA to located the sacrificial anode 12 within 10 inches of a center axis of the hot liquid inlet.”). This support for Petitioner’s proposed construction provides further reason for us to adopt it. Because it is supported by the intrinsic evidence of record, because Patent Owner proposes no alternative construction, and because Petitioner’s expert supports it, we adopt the construction of “within 10 inches of a hot liquid inlet to the radiator” that Petitioner proposes. Thus, we construe this term as “within 10 inches of the center axis of a hot liquid inlet to the radiator.” In other words, when discussing the distance between a hot liquid inlet and a sacrificial anode, we interpret “hot liquid inlet” as “center axis of the hot liquid inlet.”” slip op. at 5
- BurdenNot shown unpatentable
“Inherency may be relied upon in arguing either anticipation or obviousness. Schering, 339 F.3d at 1377 (applying inherency in an anticipation context); Par Pharma. Inc. v. TWI Pharma., Inc., 773 F.3d 1186, 1195–96 (Fed. Cir. 2014) (applying inherency in an obviousness context). In both cases, however, “[t]he mere fact that a certain thing may result from a given set of circumstances is not sufficient.” Therasense, Inc. v. Becton, Dickinson & Co., 593 F.3d 1325, 1332 (Fed. Cir. 2010). Instead, “the limitation at issue necessarily must be present, or the natural result of the combination of elements expressly disclosed by the prior art.” Par Pharma., 773 F.3d at 1195–96. Here, Petitioner has not shown sufficiently that, in Godefroy, the sacrificial anode necessarily is placed within 10 inches of the center axis of the hot liquid inlet. Dr. Medlin testifies that Figure 1 of Godefroy shows that “an entirety . . . or at least a significant portion of the sacrificial anode 14, is within 10 inches of a center axis of the inlet.” Ex. 1004 ¶ 144. But we cannot say that Figure 1 of Godefroy is clear on its face, or reasonably suggests, that this is necessarily the case. There are no dimensions shown on Figure 1, so it is unclear from the figure what the diameter of pipe 12 is. If that diameter is larger than 20 inches, then it simply is untrue that “sacrificial anode 14 is . . . necessarily placed within 10 inches of a center axis of a hot liquid inlet to the radiator,” as Dr. Medlin testifies. Id. ¶ 361. As noted above, neither Petitioner nor Dr. Medlin relies on the hot liquid inlet of Godefroy having any particular diameter, and Godefroy is silent as to the diameter of its inlet. Pet. 69–70; Ex. 1004 ¶¶ 144, 359–361, 381–382, 406–408; Ex. 1008, 1–15. Moreover, as Patent Owner notes, there is a wide range of sizes of radiators, including automobile radiators, available. Prelim. Resp. 3–5; Exs. 2001–2003. In the absence of any testimony or other evidence that tends to show that radiator inlet pipes necessarily have diameters less than 20 inches, Petitioner has not shown sufficiently that the diameter of Godefroy’s inlet pipe is small enough to ensure that any portion of the anode necessarily is within 10 inches of the center axis of the inlet.” slip op. at 11
Claim constructioncites Phillips - PTAB · Nov 14, 2016 · IPR2015-01243 · APJ Grace Karaffa Obermann · IPR · Final written decision
Petitioner failed to prove claims 1–8, 10, and 11 of the ’290 patent, claims 1–8 and 10–13 of the ’173 patent, and claims 1–6 and 8–19 of the ’510 patent obvious over Fohr, Sato, and …
RulingsFinal written decision- Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable
“We recognize that it may be necessary “to look to interrelated teachings of multiple patents . . . in order to determine whether there was an apparent reason to combine the known elements in the fashion claimed.” KSR Int’l, 550 U.S. at 418. Petitioner in these proceedings, however, directs us to no persuasive reason why an ordinary artisan would have turned to the heat-retaining battery module of Hallaj when working to implement a plurality of Sato’s cells in a pack to replace the capacitors in Fohr. Pet. 36–38 (nowhere addressing that critical point); Reply 13 (devoting four sentences to rebuttal of Patent Owner’s persuasive evidence that one would not have combined the disclosures of Hallaj, Fohr, and Sato in the manner claimed); see Ex. 1033, 15 (Examiner’s observation, in confirming the patentability of the challenged claims during reexamination, that Sato contains “no information as to how Sato’s cells would be implemented in a pack”). We view Petitioner’s unexplained leap from the single battery cell of Sato to the heat-retaining battery module of Hallaj as a classic example of impermissible hindsight reconstruction driven not by any teaching in the prior art, but by the claim requirement of a “plurality” of cells implemented in a battery pack. Pet. 36–38; Reply 13. Patent Owner, by contrast, comes forward with persuasive evidence, which we credit, showing that one of ordinary skill in the art would not have been led to arrange a plurality of Sato’s cells in the heat-retaining battery module of Hallaj because such a modified battery pack would have been unsuitable for use as a replacement for the capacitors in Fohr. Specifically, we credit the testimony of Dr. Blomgren, who cogently explains why a person of ordinary skill in the art would not have been led to the proposed modification. Ex. 2147 ¶¶ 79–85.” slip op. at 17
- Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner
“We are not persuaded by Dr. Riley’s testimony that Fohr effectively teaches that both lithium-based battery cells and capacitors can achieve the 20 Amp Limitation, on a theory that “it’s actually the tool that draws the power” and “the right lithium cell” would be “a drop in replacement for this application.” Ex. 2169, 121:12–16 (Dr. Riley’s deposition testimony); Resp. 17. Dr. Riley readily admitted an unfamiliarity with capacitors, and identified no suitable “drop in” ready lithium cells available at the time of the invention. Ex. 2169, 121:11–122:4 (“[I]f I had a cell that could do similar things, I’d certainly swap it in there.”). On that point, we find more credible Dr. Blomgren’s testimony that “there is no guarantee that a given pack of battery cells can provide the current that a tool tries to draw.” Resp. 17 (citing Ex. 2147 ¶ 60).” slip op. at 13
- Skill levelSkill level board ownOther
“B. Level of Ordinary Skill in the Art We hold that the prior art references asserted in the Petition are representative of the level of ordinary skill in the art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (absence of specific findings on “level of skill in the art does not give rise to reversible error ‘where the prior art itself reflects an appropriate level and a need for testimony is not shown’” (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163 (Fed. Cir. 1985)). To the extent that a more specific definition is required, we hold that an ordinary artisan would include one holding a Bachelor’s Degree in Electrical Engineering with two or three years of experience in battery design. That definition comports with the very similar definitions advanced by the parties. In that regard, Petitioner asserts that an ordinary artisan would encompass a person holding a Bachelor’s Degree in Electrical Engineering with three years of experience in battery design. Pet. 8; Ex. 1007 ¶ 9. Patent Owner similarly asserts that an ordinary artisan would include a person holding a Bachelor’s Degree in Electrical Engineering with two years of battery design experience. Resp. 8; Ex. 2105 ¶ 24.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed board ownDecided for patent owner
“In our Decisions to Institute, we construed the 20 Amp Limitation to require that “the battery cells, when configured together in a battery pack, are capable of producing reasonably close to 20 amps of discharge current or greater over the course of delivering their entire rated capacity.” Dec. 5. Neither party disputes that construction, which we adopt for the purposes of this Final Written Decision. To the extent that any other claim term requires express construction, we discuss the construction in our analysis below. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (only claim terms in controversy need be construed, and then only to the extent necessary to resolve the controversy). The following facts are supported by a preponderance of the evidence.” slip op. at 10
Claim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 7,944,173 - PTAB · Aug 4, 2014 · IPR2014-00731 · APJ Jacqueline Wright Bonilla · IPR · Order
The Board granted the joint motion to terminate the proceeding and the request to keep the settlement agreement confidential; no institution decision was made.
RulingsOther- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Not reached
“This case is in the preliminary proceeding1 stage; no decision whether to” slip op. at 2
- PTAB / AIA Trials › Other PTAB motions (exclude, strike, seal, additional discovery, rehearing)Granted
“The Board generally expects that a proceeding will terminate after the filing of a settlement agreement. See, e.g., Office Patent Trial Practice Guide, 77 Fed. Reg. 48,756, 48,768 (Aug. 14, 2012). Considering the facts and early stage of this 1 A preliminary proceeding begins with the filing of a petition for instituting a trial and ends with a written decision as to whether trial will be instituted. 37 C.F.R. § 42.2. proceeding, we agree with the parties that it is appropriate to terminate this proceeding.” slip op. at 2
NonePatents in suitUS 8,071,073 - PTAB · Jul 8, 2014 · IPR2014-00112 · APJ Grace Karaffa Obermann · IPR · Order
The Board granted the parties’ joint motion to terminate the instituted proceeding based on their settlement.
RulingsOther- PTAB / AIA Trials › Other PTAB motions (exclude, strike, seal, additional discovery, rehearing)Granted
“On June 27, 2014, the parties filed a joint motion to terminate the proceeding. Paper 19. Accompanying the motion, the parties filed a true copy of (1) a Settlement Agreement resolving the dispute that is the subject of this proceeding (Ex. 1017); and (2) a License Agreement between Patent Owner and its licensee, AngleFix (Ex. 1018). The parties request that both documents be treated as business confidential information, to be kept separate from the patent file pursuant to 35 U.S.C. § 317(b) and 37 C.F.R. § 42.74. Paper 20. We authorized the filing of those papers in a telephonic conference conducted June 24, 2014. Paper 18. A Decision to Institute an inter partes review in this case was entered by the Board on April 8, 2014. Paper 15. An initial conference call was conducted on May 12, 2014. Paper 17. This case is in a preliminary stage; no significant activity has occurred since entry of our Decision to Institute. Based on the facts of the case, it is appropriate to terminate the proceeding. Therefore, the joint motion to terminate the proceeding is granted.” slip op. at 2
NonePatents in suitUS 6,955,677 - PTAB · Jun 25, 2014 · IPR2014-00133 · APJ Grace Karaffa Obermann · IPR · Order
The Board granted the parties’ joint motion and terminated the proceeding after settlement.
RulingsOther- PTAB / AIA Trials › Other PTAB motions (exclude, strike, seal, additional discovery, rehearing)Granted
“On June 16, 2014, pursuant to 35 U.S.C. § 317(a), the parties filed a joint motion to terminate the proceedings. Paper 18. Accompanying the motion, the parties filed a true copy of a settlement agreement along with a joint request to treat the settlement agreement as business confidential, to be kept separate from the patent file pursuant to 35 U.S.C. § 317(b) and 37 C.F.R. § 42.74. Paper 19; Ex. 2001. The parties sought, and the Board granted, authorization for the filing of joint motions to terminate these proceedings and requests to file the settlement agreement as business confidential information. A decision to institute an inter partes review in this case was entered by the Board on May 15, 2014. An initial conference was held on June 17, 2014. No significant activity has occurred since entry of our decision to institute. Based on the facts of the case, it is appropriate to terminate the proceeding. Therefore, the joint motion to terminate the proceeding is granted.” slip op. at 2
NonePatents in suitUS 7,537,706 - PTAB · Jun 25, 2014 · IPR2014-00132 · APJ Grace Karaffa Obermann · IPR · Order
The Board granted the parties’ joint motion to terminate the proceeding and their request to keep the settlement agreement confidential.
RulingsOther- PTAB / AIA Trials › Other PTAB motions (exclude, strike, seal, additional discovery, rehearing)Granted
“Board on May 15, 2014. An initial conference was held on June 17, 2014. No significant activity has occurred since entry of our decision to institute. Based on the facts of the case, it is appropriate to terminate the proceeding. Therefore, the joint motion to terminate the proceeding is granted. Accordingly, it is ORDERED that the parties’ joint request that the settlement agreement be treated as business confidential information, to be kept separate from the patent file, is granted; FURTHER ORDERED that the joint motion to terminate the proceeding is granted; and FURTHER ORDERED that the proceeding is terminated.” slip op. at 2
NonePatents in suitUS 7,033,492 - PTAB · Jan 30, 2014 · IPR2014-00078 · APJ Grace Karaffa Obermann · IPR · Order
The Board granted the parties’ joint motion and terminated the proceeding before deciding whether to institute trial.
RulingsOther- PTAB / AIA Trials › Other PTAB motions (exclude, strike, seal, additional discovery, rehearing)Granted
“On January 24, 2014, pursuant to 35 U.S.C. § 317(a), the parties filed a joint motion to terminate this proceeding. Paper 9. Accompanying the motion, the parties filed a true copy of a settlement agreement (Ex. 2001-02) along with a joint request to treat the settlement agreement as business confidential, to be kept separate from the patent file pursuant to 35 U.S.C. § 317(b) and 37 C.F.R. § 42.74 (Paper 8). We authorized the filing of these papers in an email of January 21, 2014. This case is in a preliminary stage; no decision whether to institute a trial has been made. Based on the facts of the case, it is appropriate to terminate the proceeding. Therefore, the joint motion to terminate the proceeding is granted.” slip op. at 2
NonePatents in suitUS 6,953,703 - PTAB · Jan 21, 2014 · IPR2014-00072 · APJ Grace Karaffa Obermann · IPR · Order
The Board granted the parties’ joint motion to terminate the proceeding before deciding whether to institute trial.
RulingsOther- PTAB / AIA Trials › Other PTAB motions (exclude, strike, seal, additional discovery, rehearing)Granted
“motion to terminate this proceeding. Accompanying the motion, the parties filed a true copy of a settlement agreement along with a joint request to treat the settlement agreement as business confidential, to be kept separate from the patent file pursuant to 35 U.S.C. § 317(b) and 37 C.F.R. § 42.74. We authorized the filing of these papers during a conference call conducted January 13, 2014. See Order entered January 14, 2014. This case is in the preliminary proceeding stage; no decision whether to institute a trial has been made. Based on the facts of the case, it is appropriate to terminate this proceeding. Therefore, the joint motion to terminate the proceeding is granted. Accordingly, it is ORDERED that the parties’ joint request that the settlement agreement be treated as business confidential information, to be kept separate from the patent file, is granted; FURTHER ORDERED that the joint motion to terminate the proceeding is granted; and FURTHER ORDERED that the proceeding is terminated.” slip op. at 2
NonePatents in suitUS 5,686,738
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.