• Bio-Rad Laboratories, Inc. v. California Institute Of TechnologyNo claims unpatentable
  PTAB · Mar 23, 2026 · IPR2024-01451 · APJ Tawen Chang · IPR · Final written decision

  Claims 1–19 were not shown unpatentable: Larson did not establish the claimed detection in a single sample volume, and the asserted obviousness combinations did not cure the deficiencies.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Patent Owner states that, “[f]or purposes of this IPR proceeding, PO does not contest Petitioner’s description of qualifications for a person of ordinary skill in the art (POSA) set forth [above].” PO Resp. 23. In view of the above, and because Petitioner’s uncontested description of one of ordinary skill in the art is reasonable and consistent with the ’921 patent and the cited art, we adopt Petitioner’s definition of a POSA for purposes of this Decision, except that we replace the phrase “at least a year of experience in quantitative and/or dPCR and fluorescence-based analyte detection” with “around a year of experience in quantitative and/or dPCR and fluorescence-based analyte detection.” Pet. 9 (emphasis added).13” slip op. at 14

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

    “We begin with “the context in which a term is used in the asserted claim,” which can be “highly instructive.” Phillips, 415 F.3d at 1314. In this case, claim 1 recites that the claimed assay is “capable of unambiguously detecting the presence or absence of each of said at least M analytes, in any combination of presence or absence, in a single sample volume, . . . wherein the analytes are amplified in the single sample 15 In this regard, we note that Petitioner’s claim construction position is not predicated on the collection of droplets being reconstituted into its original, pre-partition form prior to amplification; rather, the droplets remain compartmentalized from each other in the PCR thermal cycling tube. Tr. 65:21–66:9 (Petitioner’s counsel explaining that the droplets do not combine in the PCR thermal cycling tube but, rather, are “suspended in an immiscible fluid and analyzed en masse”). indicates that the first instance of single sample volume, i.e., the single sample volume in which the presence or absence of each M analytes are to be detected, is the antecedent basis for the second instance of “single sample volume,” i.e., the single sample volume in which the analytes are amplified. Thus, as the parties appear to agree, the single sample volume in which amplification takes places must be the same single sample volume in which the presence or absence of analytes are to be detected. We are not persuaded that, when accorded its plain and ordinary meaning, a single sample volume divided into a collection of droplets would be considered the “same” single sample volume prior to its partition.” slip op. at 17

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

    “With respect to the limitation, “wherein the analytes are amplified in the single sample volume,” Petitioner asserts that “Larson discloses PCR assays that amplify target polynucleotide in a single sample volume, specifically a portion of the reaction mixture that is subsequently partitioned into droplets.” Pet. 31 (emphasis added). There is no dispute that the amplification of the analytes in Larson occurs in the droplets. Larson ¶¶ 6–7 (explaining that “[d]igital PCR (dPCR) is an alternative quantitation method in which dilute sample are divided into many separate reactions” and that “[t]he template is amplified in the droplet for detection”) (emphasis added). Because the claims require that amplification of the analytes be in the same sample volume in which the at least M analytes, in any combination of presence or absence, is unambiguously detected, and because the pre-partition single sample volume is not the same single sample volume as the collection of droplets after partition under our claim construction set forth above, we find Petitioner has not shown, by a preponderance of evidence, that claims 1–10 and 13–19 are anticipated by Larson.17 Tr. 68:12–69:14 (Petitioner’s counsel” slip op. at 27

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable

    “Although we agree with Petitioner that Larson contemplates scenarios in which droplets may contain more than one target molecule and does not require the exclusion of such multiple occupancy droplets in all embodiments, we are nevertheless not persuaded Petitioner has shown, based on a preponderance of evidence, that Larson renders obvious an assay capable of unambiguously detecting, in such multiple occupancy droplets, the presence or absence of each of at least M analytes, in any combination of presence or absence, when M is greater than F and F is at least 2.” slip op. at 32

  Patent outcomesUS 11,827,921 not shown unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 11,827,921
• Penumbra, Inc. v. Rapidpulse, Inc.No claims unpatentable
  PTAB · Feb 17, 2026 · IPR2024-01261 · APJ Jamie T Wisz · IPR · Final written decision

  Claims 1–20 were not shown unpatentable because the asserted combinations did not teach the claimed predetermined cycle for controlling distal fluid flow.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “(1) a person with a B.S. in engineering or an equivalent field, with two-four years of academic or industry experience in aspiration embolectomy and thrombectomy or comparable industry experience who would, where appropriate, work or consult with others, including a physician, to develop embolectomy or thrombectomy devices; or (2) an interventional neurosurgeon with at least three years of experience developing and/or using medical devices in embolectomy or thrombectomy procedures, and who would, where appropriate, work or consult with others, including an engineer, to develop such a medical device. Pet. 11 (citing Ex. 1005 ¶ 48). Petitioner also contends that, “[a] person with less education but more relevant practical experience, or more relevant education but less practical experience, may also meet this standard.” Id. Patent Owner states that for purposes of its PO Response, it “accepts ¶ 44). We adopt Petitioner’s characterization because it is consistent with the level of skill in the art at the time of the invention as reflected by the ’402 patent and the cited prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (explaining that specific findings regarding ordinary skill level are not required “where the prior art itself reflects an appropriate level and a need for testimony is not shown” (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163 (Fed. Cir. 1985))).” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

    “specification explicitly includes sensors similar to those in the prior art in support of their argument that the claimed “predetermined cycle” must not exclude the use of such sensors. Pet. Reply 15 (citing Ex. 1001, 32:55–33:7, 40:66–41:5, 44:9–29). We reviewed the portions of the specification cited by Petitioner. We agree with Patent Owner that one excerpt discussing sensor use appears to be directed to triggering the predetermined cycle rather than causing timing changes during the cycle itself (Ex. 1001, 32:55–66) (describing use of a pressure sensor to “determine when the vacuum channel 3 is clogged by a thrombus and automatically perform the unclogging procedures described herein”), while another excerpt discusses a sensor that Petitioner that the ’402 patent discusses the use of sensors to “tune” the system and that such “tuning” can be done statically (setting the cycle timing in advance) or dynamically (adjusting the timing during the cycle itself). See Ex. 1001, 48:19–49:50. Overall, we find that these disclosures involving sensors demonstrate that sensors may be used in various ways in different embodiments. However, none of these disclosures explicitly discuss the use of sensors in conjunction with a “pre-determined cycle.” Therefore, we find that the ’402 patent specification’s discussion of “sensors” are not particularly informative as to the appropriate construction of a “predetermined cycle” and do not outweigh the other explicit disclosures of “predetermined cycle” in the patent. We next turn to the other intrinsic evidence discussed by the parties — the prosecution history. As discussed by Patent Owner, in the Notice of Allowance, the Examiner found that Garrison did not teach or suggest a “predetermined cycle” because Garrison’s controller “changed the cycle of opening and closing the valves based on feedback from sensors.” Ex. 1004, 86. We acknowledge that the patent applicant filed subsequent comments during prosecution in which they stated that they “do[] not concede that the Examiner’s characterizations of the terms of the claims and the prior art are correct.” Id. at 29. However, we agree with Patent Owner that the importance of the Examiner’s statement in the Notice of Allowance does not rely on it being an express disclaimer (a standard which it does not meet). PO Sur-reply 8. We also considered Petitioner’s contention that the Examiner’s interpretation of Garrison may have been in error (PO Resp. 16); however, even if this were true, the Examiner’s statement still provides helpful insight into how the Examiner was interpreting the term sensors to change the opening and closing of valves during a cycle was not a “predetermined cycle.” Id. at 86. In sum, we find that Patent Owner’s proposed construction is consistent with the usage of the term “predetermined cycle” in the ’402 patent specification and prosecution history. Thus, after considering all of the cited evidence, we construe “predetermined cycle” to mean that “the timing of the sequence of valve operations in the cycle is determined beforehand, i.e., fixed, rather than varying based on feedback after operation begins.”” slip op. at 14

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “2. Other Terms The parties also provided proposed constructions for the limitations of “[limited/limiting] to a positive amount of exit flow” and “control[ling] fluid flow in and out from the distal end of the catheter.” See Pet. 15–16; Pet. Reply 1–8; PO Resp. 22–24; PO Sur-Reply 2–6. However, having evaluated the arguments and evidence before us, we determine that construction of these terms is not necessary for purposes of this Decision. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 16

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableNot shown unpatentable

    “We agree with Patent Owner that neither Petitioner nor Mr. Brown propose any combination of Yang and Mullins that does not include Mullins’s pressure sensor in order “to control fluid flow in and out from the distal end of the catheter.” Indeed, in addressing the “predetermined cycle” limitation, Mr. Brown contends that Mullins discloses a “cycling controller that ‘varies aspiration pressure according to sensed pressure within the catheter lumen.’” Ex.1005 ¶¶ 131–32 (citing, e.g., Ex.1008, 27:40–28:20 (“[a] novel aspect of this pump system is the incorporation of feedback into the pump algorithm in order to produce more effective pressure cycling”)). This use of a sensor to change pressure during a cycle, is not a “predetermined cycle” under our construction. combinations is its discussion of distal end flow control, not for its sensors.” Pet. Reply 17 (citing Ex. 1035 ¶ 83). However, Petitioner’s obviousness grounds rely on the combination of Yang and Mullins, especially with regard to Mullins’s disclosure of “a controller” in order “to control fluid flow in and out.” As discussed above, Mullins relies on the sensor-feedback approach in order to control flow and we find that Petitioner has not presented persuasive evidence of how the combined disclosures of Yang and Mullins would control flow without using Mullins’s sensor feedback approach. See W.L. Gore & Assocs., Inc. v. Garlock, Inc., 721 F.2d 1540, 1550 (Fed. Cir. 1983) (error to “consider[] … references in less than their entireties, i.e., in disregarding disclosures in [them] … that diverge from and teach away from the invention”). Therefore, we determine that Petitioner has not sufficiently shown that the combination of Yang and Mullins discloses or renders obvious “a controller configured to open and close the vacuum valve and the vent valve in a predetermined cycle to change a level of vacuum at the distal end of the catheter and to control fluid flow in and out from the distal end of the catheter.” Accordingly, having considered the parties’ respective evidence and arguments, we find that Petitioner has not shown by a preponderance of the evidence that claim 1 of the ’402 patent would have been unpatentable as obvious over the combination of Yang and Mullins.” slip op. at 27

  Patent outcomesUS 11,406,402 not shown unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 11,406,402
• Axion Biosystems, Inc. v. Agilent Technologies, Inc.No claims unpatentable
  PTAB · Feb 2, 2026 · IPR2024-01467 · APJ David Cotta · IPR · Final written decision

  Claims 1–8 and 11–15 were not shown unpatentable over Xu-752 and Jones because the proposed combination did not establish obvious millisecond time resolution.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “B. Level of Ordinary Skill in the Art Petitioner contends a person of ordinary skill in the art (“POSA”) as of May 2009 “would have had a B.S. in electrical/mechanical/biomedical engineering or biological science, or a related field, and approximately 2 years of relevant experience or equivalent study in systems and methods for bioanalysis of cells.” Pet. 14 (citing Ex. 1003 ¶¶ 23–25). Patent Owner adopts this definition for purposes of this proceeding. PO Resp. 9 (citing Ex. 2009 ¶ 19). We find Petitioner’s description of the level of ordinary skill in the art to be consistent with the level of skill reflected in the ’508 patent and in the prior art of record. Accordingly, we apply Petitioner’s definition in this decision.” slip op. at 7

  • Claim Construction › Intrinsic evidence (Phillips canons) › Lexicography (patentee as own lexicographer)Term construed petitioner constructionDecided for petitioner

    “As used herein, “impedance measurement at millisecond time resolution” refers to the ability to perform a series of at least two consecutive impedance measurements within milliseconds of one another for each and every well of the system where each well is associated with an electrode array for impedance measurement. In each instance the time between two consecutive impedance measurements are less than 300 milliseconds from one another. Id. at 10:8–15. There does not appear to be any dispute as to the definitional nature of the first sentence in the passage above. That is, the parties agree that millisecond time resolution should be construed to mean: “the time between two consecutive impedance measurements for each and every well being evaluated in the claimed apparatus or system.” PO Resp. 15 (proposing construction); Pet. Reply. 23 (“Axion also agrees that the term ‘millisecond time resolution’ is ‘the time between two consecutive impedance measurements for each and every well being evaluated in the claimed apparatus or system.’”). The parties also agree that we do not need to determine whether the time interval between two consecutive impedance measurements is less than 300 milliseconds, as set forth in the definition portion of the specification, or whether it can be met by some other time interval, as suggested by other portions of the specification. See e.g., Ex. 1001, 23:49–55 (explaining that “[i]n some embodiments 500 millisecond time resolution is sufficient”), 24:37–39 (similar); PO Resp. 15 (arguing that “the distinction between 300 milliseconds and 500 milliseconds is immaterial to the dispute in this IPR because Jones teaches a 1.5 second update period, thus at least three times longer than the 500 milliseconds formulation”); Pet. Reply 23–24 (section headed “[Petitioner] Agrees That, In This IPR, The 300 Versus 500 Milliseconds Distinction is Immaterial To Addressing the Unpatentability of the Challenged Claims”), see also, Pet. Reply 24–26 (asserting that the claims are indefinite because it is not clear whether they require a 300 or a 500 millisecond time interval, but arguing that “the claims’ unpatentability can be determined without resolving the 300 versus 500 milliseconds indefiniteness issue”). We agree with the parties that “millisecond time resolution” should be construed to mean: “the time between two consecutive impedance measurements for each and every well being evaluated in the claimed apparatus or system.” PO Resp. 15; Pet. Reply. 23. We further agree that resolution of this case does not require that we determine whether the period between two consecutive impedance measurements is less than 300 or less than 500 milliseconds because Petitioner has not carried its burden under either time interval.” slip op. at 7

  • Expert testimonyPetitioner expert discountedDecided for patent owner

    “Ex. 1003 ¶ 179. But Dr. Kim does not cite to any additional supporting evidence or provide any technical reasoning to support his statements. The notion that one can reduce the time between measurements by, e.g., reducing the number of frequencies measured, has intuitive appeal and appears mathematically correct. However, the absence of technical reasoning and supporting evidence diminishes the persuasiveness of Dr. Kim’s testimony that the POSA would made such modifications to reduce the time between measurements. Dr. Kim does provide some technical reasoning in connection with his discussion of eliminating all reference channels as a way to get the time resolution down to the levels required by, e.g., claim 14, which recites a millisecond time resolution of “less than 5 milliseconds.” See e.g., Ex. 1003 ¶ 172 (“A POSA seeking to study biological cell phenomena occurring on the order of a few milliseconds would have recognized that after measuring the reference network channels at the start, the reference network channels would not need measured again for some time, e.g., because temperature and other drift factors do not change appreciably on a millisecond time scale.”). However, even if we were to credit this testimony, Dr. Kim still lacks support and reasoning for the selection of the other parameters in his noreference-channel calculations. See, e.g., id. ¶ 173 (positing, but not providing technical reasoning for using, a no-reference-channel impedance system with 16 wells, a single 10kHz measurement frequency, and 16 daughter boards that measure simultaneously rather than sequentially).” slip op. at 29

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightMotivation not foundNot shown unpatentableNot shown unpatentable

    “Given that Jones’s only exemplified embodiment targets a 1.5 second update period, that Jones does not suggest reducing the update period, and that much of Jones’s focus is on benefits other than speed of measurement, Jones’s impedance analyzer seems an unlikely choice for a POSA seeking to take measurements having millisecond time resolution. Put another way, we find no persuasive non-hindsight reason that supports Petitioner’s assertion that the POSA would have sought to apply Jones’s impedance analyzer to Xu-752’s system in order to take measurements in millisecond time resolution.” slip op. at 22

  Patent outcomesUS 11,906,508 not shown unpatentable
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,906,508
• Champion Laboratories, Inc. / First Brands Group, LLC v. Hengst SENo claims unpatentable
  PTAB · Sep 8, 2025 · IPR2024-00603 · APJ Sheldon M Mcgee · IPR · Final written decision

  Claims 1, 3, 5, 8–11, 15–17, 19, 23–25, and 28–30 were not shown unpatentable over Yokoyama, Yokoyama and Cline, or Honermann and Cline.

  RulingsFinal written decision

  • Skill levelSkill level board ownDecided for petitioner

    “On this record, we determine that the level of ordinary skill is reflected in the prior art of record. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (specific findings on the ordinary skill level are not required “where the prior art itself reflects an appropriate level and a need for testimony is not shown” (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163–64 (Fed. Cir. 1985))). Because the level of ordinary skill in the art is not in dispute, and because the parties’ definition is consistent with the disclosures in the ʼ203 patent, the prior art, and the declaration testimony of Mr. Nranian and Dr. Basirat, we view the prior art and arguments through this lens when determining whether the claims are unpatentable as obvious over the prior art.5 See Graham, 383 U.S. at 17 (identifying “the level of ordinary skill in the pertinent art” as an underlying factual inquiry to be resolved in deciding obviousness, which is a question of law).” slip op. at 12

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

    “Although the parties spend significant portions of their briefing discussing the term “eccentric” and how it applies to certain figures from the ʼ203 patent and the relied-upon prior art, we determine that it is not necessary to expressly construe the term “eccentric” beyond the parties’ agreed-upon definition. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co. Ltd., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (holding that only claim terms in controversy need to be construed, and only to the extent necessary to resolve the controversy (citing Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))). Rather, we adopt Patent Owner’s proffered definition because it is consistent with the intrinsic record and because it is not in dispute. Specifically, Patent Owner asserts that the plain meaning of the term “eccentric” is defined as “located elsewhere than at the geometric center; also: having the axis or support so located.” PO Resp. 18–19 (citing the Merriam-Webster online dictionary definition of the term “eccentric” for support). Petitioner agrees with this definition. Pet. 35 (asserting that certain prior art elements are eccentric “because they are not located at the center of the filter insert or housing”); Pet. Reply 9 (arguing that certain elements are eccentric because they “do not have an axis located at the geometric center”); id. at 10 (arguing the eccentricity of an element that does “not have an axis in the center” which has “an off-center axis”); see also Ex. 2017 ¶ 33 (Dr. Basirat testifying that “[a] POSITA would understand that ‘eccentric’ in the context of [the] ʼ203 patent, means that central axis is located elsewhere than at the geometric center [and] not placed centrally or not having its axis or other part placed centrally”). The parties’ definition of “eccentric” is also consistent with the usage of the term in the ʼ203 patent. Ex. 1001, 10:23–31; Fig. 17.” slip op. at 14

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

    “Rather, we adopt Patent Owner’s proffered definition because it is consistent with the intrinsic record and because it is not in dispute. Specifically, Patent Owner asserts that the plain meaning of the term “eccentric” is defined as “located elsewhere than at the geometric center; also: having the axis or support so located.” PO Resp. 18–19 (citing the Merriam-Webster online dictionary definition of the term “eccentric” for support). Petitioner agrees with this definition. Pet. 35 (asserting that certain prior art elements are eccentric “because they are not located at the center of the filter insert or housing”); Pet. Reply 9 (arguing that certain elements are eccentric because they “do not have an axis located at the geometric center”); id. at 10 (arguing the eccentricity of an element that does “not have an axis in the center” which has “an off-center axis”); see also Ex. 2017 ¶ 33 (Dr. Basirat testifying that “[a] POSITA would understand that ‘eccentric’ in the context of [the] ʼ203 patent, means that central axis is located elsewhere than at the geometric center [and] not placed centrally or not having its axis or other part placed centrally”). The parties’ definition of “eccentric” is also consistent with the usage of the term in the ʼ203 patent. Ex. 1001, 10:23–31; Fig. 17.” slip op. at 14

  • Expert testimonyPetitioner expert discountedDecided for patent owner

    “(opining that “Patent Owner’s construction of ‘having an axis no located in a geometric center’ is too narrow”). Mr. Nranian’s Declaration testimony in this respect is not persuasive for several reasons. First, it is internally inconsistent. Compare Ex. 1016 ¶ 3 (criticizing the “axis” language in Patent Owner’s definition), with id. ¶¶ 9, 11 (relying on that very language to support an argument). Also, Mr. Nranian’s proposed definition of “eccentric” to merely mean “not located at the center” begs the question of what, precisely, is “the center”? Mr. Nranian does not persuasively explain how far a person of ordinary skill in the art would understand she could travel from the exact center point of an object and still be in “the center” of that object. See Tr. 10:13–19 (Judge McGee asking whether the center is “a miniscule point in the middle of [the] disc”); see also id. at 10:25–12:26 (Judge Weatherly highlighting the significant ambiguity in referring to something as in “the center”). Also, Mr. Nranian’s opinion is inconsistent with how the ʼ203 patent compares something that is “central,” i.e., “at the center,” and something that is “eccentrically” located. Ex. 1001, 7:13–14 (describing pipe nozzle 15 as “central”); id. at 8:53–56 (describing a “through hole” as “located in the center of the front panel 22” depicted in Figures 7 and 8); id. at 10:23–31 (describing return 12 as “in the center” and outlet 13 as “eccentrically thereto” in Figure 17). Patent Owner’s colorized and annotated Figure 7 is reproduced below: Patent Owner’s colorized and annotated version of Figure 7 of the ʼ203 patent illustrates “central pipe nozzle 15” in yellow passing through the “through hole” located in “the center” of front panel 22. PO Resp. 20. Significantly, pipe nozzle 15 and the through hole in panel 22 are both described as “central” and in “the center” but must have different diameters; otherwise, “central pipe nozzle 15” would not be capable of traveling through “through hole 22.” Ex. 1001, Fig. 7. Thus, the ʼ203 patent intrinsically bases whether an element is “central” or “in the center” on whether its axis is located at the geometric center. This is also illustrated in Figure 17 of the ʼ203 patent, reproduced below: Figure 17 of the ʼ203 patent illustrates filter housing 10 with return 12 “in the center . . . and, eccentrically thereto, the outlet 13 with the seat 14 for the blocking element 24.” Ex. 1001, 10:23–30. Finally, Mr. Nranian’s narrow interpretation of “eccentric”––which excludes the “having the axis or support so located” in the geometric center language––is at odds with the arguments it was proffered to support. Cf. Pet. Reply 9 (arguing that certain elements are eccentric because they “do not have an axis located at the geometric center”); id. at 10 (arguing the eccentricity of an element that does “not have an axis in the center” which has “an off-center axis”).” slip op. at 29

  Patent outcomesUS 9,023,203 not shown unpatentable
  Claim construction§ 103 obviousnesscites Graham
  Patents in suitUS 9,023,203
• Inergy Technology, Inc. v. Force Mos Technology Co., Ltd.No claims unpatentable
  PTAB · May 16, 2025 · IPR2024-00093 · APJ Grace Karaffa Obermann · IPR · Final written decision

  Claims 1–9 were not proven unpatentable because the asserted references did not establish the claimed epitaxial layer or the required coverage of the trench sidewalls.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner defines a person of ordinary skill in the art as having “a Master’s degree in electrical engineering, and at least two years of relevant work experience in the field of integrated circuit design and manufacturing.” Pet. 13 (citing Ex. 1003 ¶¶ 32–37, 57). Patent Owner does not dispute Petitioner’s definition. PO Resp. 6. We adopt Petitioner’s proposed definition of the level of ordinary skill in the art because it is supported by unopposed declaration testimony and appears to be consistent with the disclosures of the ’634 patent and the asserted prior art references. See Ex. 1001, 1:6–2:33 (describing the invention and related art in terms of integrated circuit design and fabrication); see also Ex. 1006 ¶¶ 1–6 (Hirler); Ex. 1008 ¶¶ 1–37 (Kobayashi); Ex. 1009 ¶¶ 2–29 (Shiraishi). Neither party, moreover, indicates the overall result would change based on a different definition.” slip op. at 7

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “Petitioner argues that “the sidewalls of said trenches in said base layer are covered” should be construed to mean that “the entire sidewalls of” those trenches are covered. Pet. 18–19. We refer to this as “the sidewall limitation.” Petitioner shows persuasively that the disclosure and file history of the ’634 patent support its position on the sidewall limitation. Id. Patent Owner, for its part, observes that, after the filing of the Petition. two District Courts adopted the construction proposed by Petitioner.” PO Resp. 21 (citing Ex. 2010, 6–9; Ex. 2011, 23). Patent Owner also agrees to apply Petitioner’s construction for purposes of this proceeding. Id. We agree with Patent Owner that an express construction of the sidewall limitation is necessary to this Decision, id., and adopt Petitioner’s undisputed definition because it is supported by the record. No other claim term requires express construction for purposes of this Decision.” slip op. at 8

  • BurdenNot shown unpatentable

    “On this record, Petitioner fails to demonstrate that any claim is unpatentable under any ground asserted in the Petition. IV. CONCLUSION For the above reasons, we determine that Petitioner fails to establish by a preponderance of the evidence that claims 1–9 of the ’634 patent are unpatentable.” slip op. at 34

  • Expert testimonyPetitioner expert discountedPatent owner expert creditedDecided for patent owner

    “Alternatively, even if we set aside that timing issue, Dr. Liu’s bare opinion, advanced for the first time during cross-examination, that an epitaxial layer is “obvious” from Hirler’s disclosure is inadequate to support the challenges. Id. at 24–25. We accord little weight to Dr. Liu’s opinion because it is conclusory. See Xerox Corp. v. Bytemark, Inc., IPR2022-00624, Paper 9 at 15 (PTAB Aug. 24, 2022) (precedential). In any event, Petitioner does not meet, on this record, the “high standard” required to establish an inherent disclosure of an epitaxial layer in Hirler. PO Resp. 24.6 Dr. Liu opined for the first time during cross-examination “that it would have been impossible to create Hirler’s more lightly doped n- drift zone layer on top of its more heavily doped n+ substrate layer other than via epitaxy.” Id. at 25 (citing Ex. 2014, 164:16– 165:20). But Patent Owner effectively refutes that proposition with evidence that such a layer “could be created by counter-doping,” even if, as Dr. Liu contends, counter-doping may have been less ideal due to “disadvantageous mobility.” Id. (citing Ex. 2012 ¶ 133; Ex. 2014, 166:15–167:8).” slip op. at 11

  Patent outcomesUS 7,629,634 not shown unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 7,629,634
• Tennant Company v. Oxygenator Water Technologies, Inc.No claims unpatentable
  PTAB · Feb 28, 2025 · IPR2021-00625 · APJ Kristina M Kalan · IPR · Remand

  Claims 13, 14, and 17–27 were not shown unpatentable because Tennant did not establish that Wikey or Davies inherently disclosed the claimed microbubbles and nanobubbles.

  RulingsRemand decision

  • RemandOther

    “The Federal Circuit vacated and remanded our anticipation determinations as to claims 13, 14, and 17–27. Tennant, 11.1 The Federal Circuit further stated: “Because we vacate and remand to the Board to consider Tennant’s anticipation argument, we do not reach Tennant’s obviousness arguments (which depends on its contention that either Wikey or Davies produce nanobubbles).” Id. at 11. On September 19, 2024, we authorized the parties to file supplemental briefing, stating also that the “parties are not authorized to present new factual assertions, provide additional exhibits, or raise new arguments beyond those directed to the issues raised in the remand.” Ex. 3001. Pursuant to this authorization, Petitioner filed an Opening Brief on Remand (Paper 61; “Pet. Br. Rem.”) in support of its contentions. Patent Owner filed a Lead Brief on Remand (Paper 62; “PO Br. Rem.”) in support of its contentions. Petitioner filed a Reply Brief on Remand (Paper 66; “Pet. Reply Br. Rem.”). Patent Owner filed a Responsive Brief on Remand (Paper 65; “PO Resp. Br. Rem.”).” slip op. at 3

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element) › Inherent disclosureInherency not foundNot shown unpatentable

    “Accordingly, and in line with our previous determination that “Wikey appears to disclose each limitation of claim 13 except ‘microbubbles and nanobubbles having a bubble diameter of less than 50 microns’” (Final Dec. 20), we determine that Petitioner has not demonstrated that Wikey inherently discloses microbubbles or nanobubbles. Accordingly, Petitioner has not demonstrated that Wikey discloses every limitation of claim 13.” slip op. at 56

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successNot reached

    “The Federal Circuit vacated and remanded our anticipation determinations as to claims 13, 14, and 17–27. Tennant, 11.1 The Federal Circuit further stated: “Because we vacate and remand to the Board to consider Tennant’s anticipation argument, we do not reach Tennant’s obviousness arguments (which depends on its contention that either Wikey or Davies produce nanobubbles).” Id. at 11.” slip op. at 3

  Patent outcomesUS RE45,415 not shown unpatentable
  § 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
• Nespresso USA, Inc. v. K-Fee System GMHBNo claims unpatentable
  PTAB · Apr 10, 2024 · IPR2022-01574 · APJ James J Mayberry · IPR · Final written decision

  Claims 1–13 were not shown unpatentable because the asserted combinations did not teach or render obvious the claimed groove entirely to the side of the chamfered mandrel.

  RulingsFinal written decision

  • Skill levelSkill level board ownPatent owner expert discountedDecided for patent owner

    “The Federal Circuit has made clear that, “[t]o offer expert testimony from the perspective of a skilled artisan in a patent case—like for claim construction, validity, or infringement—a witness must at least have ordinary skill in the art.” Kyocera Senco Indus. Tools Inc. v. Int’l Trade Comm’n, 22 F.4th 1369, 1376–77 (Fed. Cir. 2022) (emphasis added). “Without that skill, the witness’[s] opinions are neither relevant nor reliable.” Id. at 1377. The Federal Circuit reasons that “‘[a]dmitting testimony from a person . . . with no skill in the pertinent art serves only to cause mischief and confuse the factfinder.’ . . . That testimony would ‘amount[ ] to nothing more than advocacy from the witness stand.’” Id. (quoting Sundance, Inc. v. DeMonte Fabricating Ltd., 550 F.3d 1356, 1362, 1364–65 (Fed. Cir. 2008)). possesses at least the level of ordinary skill in the art. Our level of ordinary skill in the art requires a bachelor’s degree in engineering plus five years of experience in design of mechanical beverage systems, or similar products, as well as experience with sensors for recognizing an identifier. Patent Owner does not persuasively account for how Dr. Howle’s experience, extensive as it may be, includes five years of experience in design of mechanical beverage systems, or similar products, as well as experience with sensors for recognizing an identifier. Cf. Kyocera, 22 F.4th at 1376 (“Dr. Pratt has advanced degrees in engineering and extensive experience in the design and manufacture of fastener driving tools. But he lacks experience in power nailer design.”).” slip op. at 21

  • Expert testimonyPatent owner expert discountedDecided for petitioner

    “The Federal Circuit has made clear that, “[t]o offer expert testimony from the perspective of a skilled artisan in a patent case—like for claim construction, validity, or infringement—a witness must at least have ordinary skill in the art.” Kyocera Senco Indus. Tools Inc. v. Int’l Trade Comm’n, 22 F.4th 1369, 1376–77 (Fed. Cir. 2022) (emphasis added). “Without that skill, the witness’[s] opinions are neither relevant nor reliable.” Id. at 1377. The Federal Circuit reasons that “‘[a]dmitting testimony from a person . . . with no skill in the pertinent art serves only to cause mischief and confuse the factfinder.’ . . . That testimony would ‘amount[ ] to nothing more than advocacy from the witness stand.’” Id. (quoting Sundance, Inc. v. DeMonte Fabricating Ltd., 550 F.3d 1356, 1362, 1364–65 (Fed. Cir. 2008)). possesses at least the level of ordinary skill in the art. Our level of ordinary skill in the art requires a bachelor’s degree in engineering plus five years of experience in design of mechanical beverage systems, or similar products, as well as experience with sensors for recognizing an identifier. Patent Owner does not persuasively account for how Dr. Howle’s experience, extensive as it may be, includes five years of experience in design of mechanical beverage systems, or similar products, as well as experience with sensors for recognizing an identifier. Cf. Kyocera, 22 F.4th at 1376 (“Dr. Pratt has advanced degrees in engineering and extensive experience in the design and manufacture of fastener driving tools. But he lacks experience in power nailer design.”).” slip op. at 21

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

    “Based on the information above, we conclude that the limitation “a groove that is laterally offset from the chamfered mandrel” requires the groove to be entirely to the side of any part of the mandrel. This construction is consistent with the words of the claim—the claim states that the groove is laterally offset from, or to the side of, the chamfered mandrel, not merely offset from a portion of or the centerline of the mandrel. This construction is also consistent with the one embodiment describing the relationship between the mandrel and groove containing the seal, which depicts the groove entirely to the side of the chamfered mandrel. We do not accept Mr. Jobin’s testimony that laterally offset is determined relative to the centerline of an object. Neither the intrinsic record nor other extrinsic evidence provides support for Mr. Jobin identifying the centerline of an object as the reference point for determining if a point is laterally offset from the object.” slip op. at 31

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable

    “We do not agree with Petitioner that Yoakim teaches a groove that is laterally offset from the chamfered mandrel. As we indicated in our claim construction section, we construe the claim term to require the groove to be entirely to the side of any part of the mandrel. We agree with Patent Owner that, as depicted in Yoakim’s Figure 35, the alleged groove is not entirely to the side of any part of the mandrel. See Pet. 69; see also Pet. Reply 19 (showing the alleged groove, in red, including a portion over the chamfered mandrel); PO Resp. 55 (same). Even if Petitioner’s position is that all of the groove must be to the side of the centerline of the mandrel, Petitioner fails to prove that Yoakim teaches such a structure. As seen in Petitioner’s illustration at page 19 of Petitioner’s Reply (reproduced above), a small portion of the groove (which Petition colorizes in red) is to the left of the centerline (shown in green). See Pet. Reply 19.” slip op. at 40

  Patent outcomesUS 11,254,491 not shown unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 11,254,491
• 3M Company v. Bay Materials, LLCNo claims unpatentable
  PTAB · Jan 16, 2024 · IPR2022-01214 · APJ Grace Karaffa Obermann · IPR · Final written decision

  Claims 1–4, 7–11, and 13 were not shown unpatentable because Petitioner did not establish the flexural-modulus limitation over Hinz and the Durasoft data sheets, with or without Sun.

  RulingsFinal written decision

  • Skill levelSkill level patent owner adoptedDecided for patent owner

    “The parties disagree about the appropriate definition of the ordinarily skilled artisan and, in particular, whether that artisan would have had experience or familiarity with processing “thermoformable polymer sheets” to form “orthodontic and dental appliances.” Resp. 8; see Pet. 10–11 n.1 (disagreeing with that proposition). We agree with Patent Owner for the following reasons.” slip op. at 8

  • Expert testimonyPetitioner expert discountedPatent owner expert creditedDecided for patent owner

    “B. Conflicting Opinion Testimony Petitioner’s own witness, Dr. Giacomin, opines that an ordinarily skilled artisan “would have been familiar with various machines and methods that would have enabled the thermoforming of multilayer dental sheets into shapes that conform with the teeth (i.e., creating a dental appliance).” Ex. 1002 ¶ 25. Nonetheless, Petitioner does not contest Patent Owner’s evidence that Dr. Giacomin himself lacks that qualification. Compare Resp. 9–10 (citing Ex. 1002 ¶¶ 1–9, 17 & n.1), with Reply (nowhere contesting that evidence). Petitioner also leaves uncontested Patent Owner’s evidence that Dr. Osswald, by contrast, possesses “the required experience” with dental appliances, including thermoforming processes for their manufacture. Compare Resp. 10 (citing Ex. 2006 ¶¶ 2–8; Ex. 2007), with Reply (nowhere contesting that evidence). Dr. Giacomin possesses excellent qualifications in the field of polymer rheology, but on this record, he demonstrates no, or inadequate, familiarity or experience with methods of thermoforming dental appliances from polymeric materials, which by his own admission is a minimum qualification of the hypothetical person of ordinary skill in the art. Ex. 1002 ¶¶ 1–11 (statement of qualifications), App’x A (curriculum vitae). Patent Owner’s witness, Dr. Osswald, by contrast, has “experience with polymer materials used in dental appliances” and “shaping operations, including thermoforming” processes for such applications. Ex. 2006 ¶¶ 5, 6. Against that backdrop, where the two witnesses’ opinions differ about the level of ordinarily skill in the art of thermoforming processes for dental appliances at the time of the invention, we credit Dr. Osswald’s opinions over those of Dr. Giacomin. We take note, moreover, that Dr. Osswald’s opinions would not change under Petitioner’s somewhat different definition of the level of ordinary skill in the art. Ex. 2006 ¶ 14.” slip op. at 11

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “C. Claim Construction Claim terms are given their ordinary and customary meaning, as understood by one of ordinary skill in the art in the context of the entire disclosure. In re Translogic Tech., Inc., 504 F.3d 1249, 1257 (Fed. Cir. 2007). We construe only terms in controversy and then only to the extent necessary to resolve the controversy. Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017). No claim term requires express construction for purposes of this Decision.” slip op. at 12

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable

    “In the absence of explanation by Petitioner, we are left to wonder why either of those two ranges reported in Sun would have been recognized as applicable, without modification, to the three-layer dental splint of Hinz. Starting with a commercially-available, two-layer sheet of hard-soft PC-TPU or hard-soft PETG-TPU thermoplastic polymers, Hinz bonds a third layer, consisting of hard PC or hard PETG, to the soft TPU layer of the two-layer material by a process of thermoforming. No prior art reference explains how that process would have been understood to affect the overall flexural modulus of the resulting three-layer, hard-soft-hard composition. Petitioner does not supply an adequate reason for combining Sun’s preferred flexural modulus range, reported for Sun’s dental appliances at a temperature of 23˚ C, to dental splints formed by Hinz from fundamentally different polymers and a fundamentally different process. See Pet. 65–68 (entirety of four-page analysis on this ground); Resp. 32–38; Sur-reply 7–14 (well-supported explanation of those fundamental differences); Reply 8–16 (Petitioner’s unpersuasive responsive positions). The flexural modulus of Sun’s dental appliance not only is temperature dependent but also varies with the flexural strength of the polymeric material at hand. Ex. 1018 ¶ 12. Too late in the Reply, Petitioner raises fact-intensive reasons why those differences would not have mattered to an ordinarily skilled artisan. Reply 8–16. In any event, we agree with Patent Owner that Petitioner glosses over “[f]undamental differences” between the polymers and processes of Sun and Hinz, differences that “are central to [the] motivation to combine inquiry” and undercut Petitioner’s view that an ordinarily skilled artisan would have understood either of Sun’s flexural modulus ranges to apply, without modification, to Hinz’s polymers and process. Resp. 33 (quoting Adidas AG v. Nike, Inc., 963 F.3d 1355, 1359 (Fed. Cir. 2020)) (first alteration in original); see Sur-reply 8–16 (Patent Owner’s persuasive arguments and evidence on point). The ground based on Sun is deficient for the above reasons.” slip op. at 25

  Patent outcomesUS 10,946,630 not shown unpatentable
  Claim construction§ 103 obviousnesscites Graham
  Patents in suitUS 10,946,630
• Markforged Inc. v. Continuous Composites, Inc.No claims unpatentable
  PTAB · Sep 26, 2023 · IPR2022-00679 · APJ Sheldon M Mcgee · IPR · Final written decision

  Claims 1–12, 20, and 21 were not proven unpatentable; the asserted obviousness grounds failed for insufficient motivation to combine, teaching away, or missing claim limitations.

  RulingsFinal written decision

  • Adverse judgmentAdverse judgmentOther

    “Patent Owner statutorily disclaimed claims 13–19 on July 25, 2023, rendering Petitioner’s Grounds 4, 9, and 10 moot. Ex. 2008. Thus, our Final Written Decision does not address Petitioner’s Grounds 4, 9, and 10. The Board heard oral arguments in an in-person hearing conducted on July 27, 2023. See Paper 23.” slip op. at 4

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “(“POSITA”) would have had a master’s or bachelor’s degree in mechanical engineering, materials science, or a related degree, and either at least 3–5 years of experience (with a master’s degree), or at least 5–6 years of experience (with a bachelor’s degree), in composite materials or additive manufacturing. Pet. 13–14 (citing Ex. 1002 ¶ 36). Patent Owner states that it “does not agree that Petitioner’s proposed level of skill in the art accurately reflects the level of ordinary skill in the art as of the priority date . . . [, but r]egardless [of] the level of skill, . . . the Petition does not show the challenged claims are unpatentable.” Resp. 14–15. Patent Owner does not propose a different level of skill in the art. See id. at 15 (“Patent Owner reserves the right to propose a level of ordinary skill in the art later in this proceeding, or in other proceedings.”). On this record, we determine that the level of ordinary skill is reflected in the prior art of record. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (specific findings on the ordinary skill level are not required “where the prior art itself reflects an appropriate level and a need for testimony is not shown” (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163 (Fed. Cir. 1985))). Although a more specific definition is not necessary, we adopt Petitioner’s proposed definition because, on this record, it is consistent with the disclosures of the asserted prior art references. Neither party, however, advances information explaining how or why the result in this case would change based on the level of ordinary skill determined by the Board.” slip op. at 7

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner advances no specific construction of any claim term, but rather proposes that “claim terms should be given their plain and ordinary meaning.” Pet. 14. Patent Owner asserts that the term “anchor” should be construed according to its plain and ordinary meaning, which, according to Patent Owner, is “contact to which the path of composite material is adhered to enable pulling of the path.” Resp. 15 (citing Ex. 2006, 2, 53). Petitioner responds that “[i]n the parallel litigation, the Court has construed ‘anchor point’ and ‘anchor’ as ‘a contact point to which the path is affixed and that serves as an origin point for the formation of the path.’” Reply 3. On the complete record, we determine that no claim term needs an express construction to resolve the controversy. C. GROUND 1 – ALLEGED OBVIOUSNESS OF CLAIMS 20 AND 21 OVER LIPSKER” slip op. at 9

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable

    “combining multiple embodiments from a single prior art reference (Resp. 31), i.e., “there must be a motivation to make the combination and a reasonable expectation that such a combination would be successful, otherwise a skilled artisan would not arrive at the claimed combination.” In re Stepan, 868 F.3d 1342, 1346 n.1 (Fed. Cir. 2017). On this record, Petitioner fails to provide any such motivation to combine the embodiment in Lipsker’s Figure 2 with those of Figures 4A, 4B, 4C, and 5 to arrive at the subject matter of claim 20. Pet. 23–31. Rather, Petitioner merely points to the disparate embodiments of Figures 2, 4A, 4B, 4C, and 5 and portions of Lipsker’s disclosure pertaining to those embodiments, and asserts that Lipsker “discloses” the individual limitations recited in claim 20. See, e.g., id. at 25 (Petitioner, relying on Figure 2, asserting that “Lipsker discloses the preamble of Claim 20”), 27 (Petitioner, relying on Figure 5, asserting that “Lipsker discloses Element 20[a]”), 28 (quoting Lipsker’s descriptions of wire and adhesive dispensed separately as depicted in Figure 2, and asserting “Lipsker discloses Element 20 [c]”), 29 (pointing to Figures 4A, 4B, and 4C and asserting “Lipsker discloses Element 20[d]”). Pointing to disparate embodiments without providing a sufficient motivation to combine them is not enough to establish the obviousness of claim 20 as a whole. See KSR Int’l Co. v. Teleflex Inc., 550 U.S. 398, 418 (2007) (holding that a claim “composed of several elements is not proved obvious merely by demonstrating that each of its elements was, independently, known in the prior art”).” slip op. at 14

  Patent outcomesUS 10,744,708 not shown unpatentable
  Claim construction§ 103 obviousnesscites Phillips · Graham
  Patents in suitUS 10,744,708
• Sigray, Inc. v. Carl Zeiss X-Ray Microscopy, Inc.No claims unpatentable
  PTAB · May 22, 2023 · IPR2022-00218 · APJ Elizabeth M Roesel · IPR · Final written decision

  Claims 1–15 were not shown unpatentable because the prior art did not establish the claimed projection magnification or scintillator; the revised contingent motion to amend was dismissed as moot.

  RulingsFinal written decision

  • Skill levelSkill level patent owner adoptedDecided for patent owner

    “We determine that the level of ordinary skill in the art, as articulated by Patent Owner, more accurately reflects the subject matter of the ’704 Patent and the asserted prior art than does Petitioner’s articulation. Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (“the prior art itself reflects an appropriate level” as evidence of the ordinary level of skill in the art) (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163 (Fed. Cir. 1985)). Petitioner does not explain how “control theory” and “applied mathematics” (Pet. 16) relate to the subject matter of the ’704 Patent and the asserted prior art, and Petitioner’s reference to requisite level of skill. Furthermore, whereas Petitioner requires a POSITA to have “x-ray and computing imaging experience” (id.), Patent Owner more particularly specifies “x-ray microtomography experience” (PO Resp. 5), which is the field of art for the ’704 Patent, as well as many of the asserted prior art references. Ex. 1001, code (54) (“High resolution direct-projection type x-ray microtomography system using synchrotron or laboratory-based x-ray source”); Ex. 1007 (discussing X-ray microcomputed tomography); Ex. 1008 (discussing X-ray nanotomography and microtomography); Ex. 1010, code (54) (“Method and apparatus for utilizing an electro-optic detector in a microtomography system”); Ex. 1011 (title: “Three-dimensional X-ray Microtomography”). For these reasons, we apply Patent Owner’s definition of a POSITA. Even if we applied Petitioner’s definition of a POSITA, however, the outcome would be the same because our resolution of the controversy does not turn on the differences between the parties’ contentions about level of ordinary skill in the art.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “In an inter partes review, we apply the same claim construction standard as would be used by a district court to construe a claim in a civil action involving the validity or infringement of a patent. 37 C.F.R. § 42.100(b). Under that standard, claim terms are given their ordinary and customary meaning, as would have been understood by a person of ordinary skill in the art at the time of the invention, in light of the language of the claims, the specification, and the prosecution history of record. Id.; Phillips v. AWH Corp., 415 F.3d 1303, 1312–19 (Fed. Cir. 2005) (en banc); Thorner v. Sony Comput. Entm’t Am. LLC, 669 F.3d 1362, 1365–66 (Fed. Cir. 2012). (“all claim terms should receive their plain and ordinary meaning”); PO Resp. 5 (applying the same constructions as Petitioner). We determine that no claim term requires express construction for purposes of resolving any controversy between the parties. Realtime Data LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 10

  • Expert testimonyPetitioner expert discountedPatent owner expert creditedDecided for patent owner

    “On balance, we find that the testimony of Drs. Bentley and Arce about Jorgensen is more credible than Dr. Kia’s testimony, which is often conclusory and insufficiently supported by the evidence. Drs. Bentley and Arce do a better job of explaining and reconciling Jorgensen’s varying descriptions of the X-ray beam than does Dr. Kia. For example, although Dr. Kia relies on Jorgensen’s repeated references to a “cone-beam,” we find that Petitioner’s evidence does not outweigh the explanations provided by Drs. Bentley and Arce, particularly in view of Jorgensen’s description of the X-ray beam as “collimated” and “shielded by a lead-wrapped brass tube.” See II.D.2.d. and e., supra. Even if we consider Petitioner’s improper new reply argument about filling the CCD, we find that argument insufficient and does not outweigh Patent Owner’s unrebutted evidence about CCD pixel size. See II.D.2.f. and g., supra. In sum, viewing the record as a whole, we find that Petitioner has not shown persuasively that Jorgensen inherently discloses projection magnification within the claimed range.” slip op. at 38

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element) › Inherent disclosureNot shown unpatentableInherency not foundNot shown unpatentable

    “standard.” Amgen Inc. v. Sandoz Inc., No. 2022-1147, 2023 WL 2994166, at *10 (Fed. Cir. Apr. 19, 2023). “Inherency . . . may not be established by probabilities or possibilities.” Oelrich, 666 F.2d at 581. “The mere fact that a certain thing may result from a given set of circumstances is not sufficient.” Id. (emphasis added). Rather, the patent challenger must “show that the natural result flowing from the operation as taught would result in the performance of the questioned function.” Id.; see PersonalWeb Technologies, LLC v. Apple, Inc., 917 F.3d 1376, 1382–83 (Fed. Cir. 2019) (determining that the Board’s reliance on inherency was improper because the structure relied upon to meet a claim element “does not necessarily exist” in the reference). As discussed above, it is undisputed that there can be no projection magnification unless the X-ray beam is diverging, and there is a vigorous dispute about whether Jorgensen teaches a diverging X-ray beam. See negatively impacted by Petitioner’s and Dr. Kia’s admittedly incorrect interpretations of Jorgensen’s disclosures concerning “projected at a 4° angle” and “the X-ray beam geometry is used to achieve magnification.” Ex. 1007, H1104; see II.D.2.b. and c., supra. On balance, we find that the testimony of Drs. Bentley and Arce about Jorgensen is more credible than Dr. Kia’s testimony, which is often conclusory and insufficiently supported by the evidence. Drs. Bentley and Arce do a better job of explaining and reconciling Jorgensen’s varying descriptions of the X-ray beam than does Dr. Kia. For example, although Dr. Kia relies on Jorgensen’s repeated references to a “cone-beam,” we find that Petitioner’s evidence does not outweigh the explanations provided by Drs. Bentley and Arce, particularly in view of Jorgensen’s description of the X-ray beam as “collimated” and “shielded by a lead-wrapped brass tube.” See II.D.2.d. and e., supra. Even if we consider Petitioner’s improper new reply argument about filling the CCD, we find that argument insufficient and does not outweigh Patent Owner’s unrebutted evidence about CCD pixel size. See II.D.2.f. and g., supra. In sum, viewing the record as a whole, we find that Petitioner has not shown persuasively that Jorgensen inherently discloses projection magnification within the claimed range.” slip op. at 37

  Patent outcomesUS 7,400,704 not shown unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 7,400,704

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.