- Aroma360, LLC v. Air Esscentials, Inc.Some claims unpatentablePTAB · Oct 6, 2026 · IPR2025-00707 · APJ Eric C Jeschke · IPR · Final written decision
Claim 5 is unpatentable over Gao-2 and over Gao-2 with Goubet; claims 1, 3, 4, and 6–8 were not shown unpatentable on any ground, and substitute claim 17 was denied.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“As noted in the Decision on Institution, Petitioner’s proposed definition appears generally consistent with the record, including the prior art. See Dec. Inst. 8 (citing In re GPAC Inc., 57 F.3d at 1579). We remove the phrase “at least” in both listed options, however, as that phrase adds ambiguity. Further, Patent Owner has not argued at trial that Petitioner’s proposal for the level of ordinary skill leads to an improper understanding of how a skilled artisan would have understood either the challenged patent or the prior art. In the analysis below, we continue to apply the level of ordinary skill in the art adopted in the Decision on Institution, as proposed by Petitioner.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Neither Petitioner nor Patent Owner propose explicit constructions for any claim terms. Pet. 16–17; PO Resp. 5–6. Based on the complete record, we need not construe explicitly any claim terms because doing so would not change the outcome of the analysis below. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 10
- Expert testimonyPetitioner expert creditedDecided for patent owner
“As an initial matter, the record here does not support any sound basis to disregard the entirety of Dr. Micklow’s Declaration for allegedly not reviewing the parties’ claim constructions. See Pet. Reply 2–3 (citing Ex. 1046, 115:15–18). Contrary to Petitioner’s argument, in the cited 11 This refers to the recitation in clauses 1F and 5F that the “diffusion assembly is disposed between said upper chamber and said lower chamber.” discussion, Dr. Micklow does not indicate that he applied an incorrect understanding of a claim term. Cf. Cordis Corp. v. Bos. Sci. Corp., 658 F.3d 1347, 1357–58 (Fed. Cir. 2011) (disregarding testimony “based on an incorrect understanding of the claim construction”), cited at Pet. Reply 1; see also Pet. Reply 3 (arguing that “Dr. Micklow’s opinion that the prior art does not render the claims obvious is premised on an interpretation of certain claim limitations that are inconsistent with both parties’ constructions” (emphasis added)). Instead, we read Dr. Micklow’s testimony as clarifying that he was not involved in claim construction at all and that, as stated, he “made [his] opinions based on what [he] read in the patents.” Ex. 1046, 112:11–12; see also id. at 115:15–18 (“I don’t know if I would even apply claim construction. I applied engineering principles to a document that had been published with the patent office.”).” slip op. at 12
- BurdenNot shown unpatentable
“referring to the same direction as the separation of the “upper chamber” and “lower chamber” (vertically in both Figure 6 of the challenged patent and Figure 1 of Goubet), we turn back now to Petitioner’s discussion of clause 1F, which includes the limitation at issue. There, Petitioner does not discuss why the “diffusion assembly” is allegedly “disposed between” the “upper chamber” and “lower chamber,” but instead, Petitioner discusses why a component of the “diffusion assembly”—the “atomizer assembly”—is allegedly “disposed between” the “upper chamber” and “lower chamber”: Pet. 39. In the end, we need not assess whether the “atomizer assembly” identified by Petitioner is “disposed between” the “upper chamber” and “lower chamber” under the proper construction of that term (which, again, we need not and do not determine here) because the “disposed between” limitation does not involve the “atomizer assembly.” Instead, we find that, by failing to address why the identified “diffusion assembly” is “disposed between” the identified “upper chamber” and “lower chamber,” Petitioner has failed to provide persuasive evidence that Goubet discloses or suggests the “disposed between” limitation. Pet. 38–39 (discussing the claim language “said diffusion assembly is disposed between said upper chamber and said lower chamber” but only discussing the location of the “atomizer assembly”); see 35 U.S.C. § 316(e) (“In an inter partes review . . . , the petitioner shall have the burden of proving a proposition of unpatentability by a preponderance of the evidence.”). For the reasons above, we find, based on the complete record, that Petitioner has not shown by a preponderance of the evidence that Goubet discloses or suggests the “disposed between” limitation.” slip op. at 22
Patent outcomesUS 10,092,918 mixedClaim construction§ 103 obviousnesscites Phillips · KSRPatents in suitUS 10,092,918 - Aroma360, LLC v. Air Esscentials, Inc.All claims unpatentablePTAB · Oct 6, 2026 · IPR2025-00706 · APJ Eric C Jeschke · IPR · Final written decision
Claims 1, 4, and 7–10 are unpatentable as obvious over Goubet and anticipated by Gao; proposed substitute claims 20 and 21 are denied as indefinite and lacking written-description support.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In the Response, Patent Owner states that it “does not dispute” the definition of one of ordinary skill in the art proposed by Petitioner, but Patent Owner “reserves the right to address [the definition] should new issues materialize.” PO Resp. 6. Patent Owner did not address this issue in the Sur-reply. As noted in the Decision on Institution, Petitioner’s proposed definition appears generally consistent with the record, including the prior art. See Dec. Inst. 8 (citing In re GPAC Inc., 57 F.3d at 1579). We remove the phrase “at least” in both listed options, however, as that phrase adds ambiguity. Further, Patent Owner has not argued at trial that Petitioner’s proposal for the level of ordinary skill leads to an improper understanding of how a skilled artisan would have understood either the challenged patent or the prior art. In the analysis below, we continue to apply the level of ordinary skill in the art adopted in the Decision on Institution, as proposed by Petitioner.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed petitioner constructionOther
“Network LLC, 929 F.3d 1350, 1357 (Fed. Cir. 2019). At first glance, the language of the limitation at issue—which, again, recites “the compressed air and the operative fluid mix together in said mixing chamber to form the fluid dispersion”—would seem to require the “fluid dispersion” (under the stipulated construction) to be fully formed in the “mixing chamber.” In other words, the language of the limitation alone would seem to support Patent Owner’s proposed construction for the “form the fluid dispersion” limitation. But the claim construction analysis does not end with consideration of the claim language alone. Next, we turn to the Specification. The Federal Circuit has said that the specification “is the single best guide to the meaning of a disputed term.” Phillips, 415 F.3d at 1315 (quoting Vitronics Corp. v. Conceptronic, Inc., 90 F.3d 1576, 1582 (Fed. Cir. 1996)). Here, the discussion in the Specification of precisely the same language as in the limitation at issue strongly supports that “to form a fluid dispersion” in the limitation at issue requires only initial mixing of the compressed air and operative fluid in the mixing chamber, with further “formation” of the ”fluid dispersion” occurring downstream of the mixing chamber: More importantly, the “predetermined amount” of compressed air and the “preselected amount” of the operable fluid are initially mixed together in the mixing chamber 226 to form a fluid dispersion. The diffusion chamber 112" is further structured to facilitate the formation of a plurality of substantially uniform droplets, as defined hereinabove, in the fluid dispersion prior to discharge from the diffusion chamber 112" through discharge port 132. Ex. 1001, 10:62–11:2 (emphasis added) (discussing Figure 6), quoted, in part, at Pet. Reply 6–710; see also Ex. 1001, 5:64–6:4 (same language, except without double primes, in a discussion of Figures 1 and 2). To be sure, certain passages in the Specification could be read to indicate that a “fluid dispersion” must be fully formed in the “mixing chamber.” See, e.g., Ex. 1001, 6:11–12 (“More in particular, the suppression chamber 232 receives the fluid dispersion from the mixing chamber 226.”); see also id. at 7:22–33, 11:39–52 (both implying that a “fluid dispersion” is formed in the mixing chamber). But the passage block quoted directly above (and the similar one bridging columns 5 and 6) more directly addresses the issue at hand—i.e., the scope of “form the fluid dispersion”—by using the same” slip op. at 13
- Expert testimonyPatent owner expert discountedMixed
“As an initial matter, the record here does not support any sound basis to disregard the entirety of Dr. Micklow’s Declaration for allegedly not reviewing the parties’ claim constructions. See Pet. Reply 2 (citing Ex. 1046, 115:15–18). Contrary to Petitioner’s argument, in the cited discussion, Dr. Micklow does not indicate that he applied an incorrect understanding of a claim term. Cf. Cordis Corp. v. Bos. Sci. Corp., 658 F.3d 1347, 1357–58 (Fed. Cir. 2011) (disregarding testimony “based on an incorrect understanding of the claim construction”), cited at Pet. Reply 1. Instead, we read Dr. Micklow’s testimony as clarifying that he was not involved in claim construction at all and that, as stated, he “made [his] opinions based on what [he] read in the patents.” Ex. 1046, 112:11–12; see also id. at 115:15–18 (“I don’t know if I would even apply claim construction. I applied engineering principles to a document that had been published with the patent office.”).” slip op. at 18
- Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable
“To satisfy its burden of proving obviousness, a petitioner cannot employ mere conclusory statements. The petitioner must instead articulate specific reasoning, based on evidence of record, to support the legal conclusion of obviousness.” In re Magnum Oil Tools Int’l, Ltd., 829 F.3d 1364, 1380 (Fed. Cir. 2016); TriVascular, Inc. v. Samuels, 812 F.3d 1056, 1066 (Fed. Cir. 2016) (“Although the KSR test is flexible, the Board ‘must still be careful not to allow hindsight reconstruction of references . . . without any explanation as to how or why the references would be combined to produce the claimed invention.’”) (citation omitted). Based on the complete record, we agree with Patent Owner that “Petitioner’s asserted motivation boils down to the conclusory statement that given Goubet and Kaiser, ‘it was well known in the field at the time of the invention that droplets of greater uniformity result in uniform droplet evaporation.’” PO Resp. 31 (quoting Pet. 59). We agree with Patent Owner that Petitioner’s discussion of the alleged reasons to combine (Pet. 59) is insufficient to support the proposed combination here. See Magnum Oil, 829 F.3d at 1380. Specifically, we are not persuaded that Kaiser’s teachings—which relate to combustion (Ex. 1014 at 43)—would have led one of ordinary skill in the art to the proposed modifications, which would allegedly “improve the smoothness (i.e., less harsh) of the aroma generated as the oil droplets evaporate in the surrounding airspace.” See Pet. 59 (emphasis added); White Pet. Decl. ¶ 251 (same); see PO Resp. 32 (“Rather, Dr. White merely describes the ability to achieve the effect as in the claimed patent, not why a [person of ordinary skill in the art] would look to the field of electrospray injection and combustion in mesoscale power-generation systems, using high-voltage electric fields to generate charged fuel droplets for controlled combustion in catalytic micro-combustors when considering atomization for scents.”). For these reasons, we determine, in light of the complete record, that Petitioner has not shown by a preponderance of the evidence that one of ordinary skill in the art at the time of the invention would have had reason to combine Goubet and Kaiser, as proposed. slip op. at 32
Patent outcomesUS 10,583,449 unpatentableClaim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · NautilusPatents in suitUS 10,583,449 - Aroma360, LLC v. Air Esscentials, Inc.All claims unpatentablePTAB · Oct 6, 2026 · IPR2025-00705 · APJ Eric C Jeschke · IPR · Final written decision
Claims 7–9 and 11 are unpatentable as obvious over Goubet; proposed substitute claim 21 is denied as indefinite.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In the Response, Patent Owner states that it “does not dispute” the definition of one of ordinary skill in the art proposed by Petitioner, but Patent Owner “reserves the right to address [the definition] should new issues materialize.” PO Resp. 5. Patent Owner did not address this issue in the Sur-reply. As noted in the Decision on Institution, Petitioner’s proposed definition appears generally consistent with the record, including the prior art. See Dec. Inst. 8 (citing In re GPAC Inc., 57 F.3d at 1579). We remove the phrase “at least” in both listed options, however, as that phrase adds ambiguity. Further, Patent Owner has not argued at trial that Petitioner’s proposal for the level of ordinary skill leads to an improper understanding of how a skilled artisan would have understood either the challenged patent or the prior art. In the analysis below, we continue to apply the level of ordinary skill in the art adopted in the Decision on Institution, as proposed by Petitioner.” slip op. at 9
- Expert testimonyPetitioner expert creditedDecided for patent owner
“The record here does not support any sound basis to disregard the entirety of Dr. Micklow’s Declaration, as asserted in Petitioner’s overall argument. See Pet. Reply 1–2. Contrary to Petitioner’s argument, in the cited general discussion, Dr. Micklow does not indicate that he applied an incorrect understanding of a claim term. Cf. Cordis Corp. v. Bos. Sci. Corp., 658 F.3d 1347, 1357–58 (Fed. Cir. 2011) (disregarding testimony “based on an incorrect understanding of the claim construction”), cited at Pet. Reply 1; see also Pet. Reply 2 (arguing that “Dr. Micklow’s declaration is premised on understandings of claim scope that are inconsistent with the constructions advanced by both of the parties” (emphasis added)). Instead, we read the cited portions of Dr. Micklow’s testimony as clarifying that he was not involved in claim construction at all and that, as stated, he “made [his] opinions based on what [he] read in the patents.” Ex. 1046, 112:11–12; see also Pet. Reply 1 (citing Ex. 1046, 112:4–12, 113:13–20, 115:15–18). Next, we turn to each of the four specific claim terms that Petitioner highlights in its further arguments.” slip op. at 12
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction needed
“B. Claim Construction In inter partes reviews, the Board interprets claim language using the same claim construction standard that would be used in a civil action under 35 U.S.C. § 282(b), as described in Phillips v. AWH Corp., 415 F.3d 1303 (Fed. Cir. 2005) (en banc). See 37 C.F.R. § 42.100(b). Under that standard, we generally give claim terms their ordinary and customary meaning, as would be understood by a person of ordinary skill in the art at the time of the invention, in light of the language of the claims, the specification, and the prosecution history. See Phillips, 415 F.3d at 1313–14. Although extrinsic evidence, when available, may also be useful when construing claim terms under this standard, extrinsic evidence should be considered in the context of the intrinsic evidence. See id. at 1317–19. Neither Petitioner nor Patent Owner propose explicit constructions for any claim terms. Pet. 10–11; PO Resp. 5. Based on the complete record, we need not construe explicitly any claim terms because doing so would not change the outcome of the analysis below. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 9
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for patent owner
“Florida Litigation a Joint Claim Construction statement that included stipulated claim constructions and disputed claim constructions for terms in the challenged patent as well as the ’449 patent and the ’918 patent. See Ex. 1018, Exhibit A (Stipulated Claim Constructions), Exhibit B (Disputed Claim Constructions). The parties stipulated to the construction of the terms “fluid dispersion” and “baffle” as recited in the challenged claim. See id., Exhibit A.10 10 When staying the Florida Litigation, the District Court cancelled the scheduled claim construction hearing. See ECF No. 67 (April 8, 2025) (granting joint motion to stay); ECF No. 68 (April 8, 2025) (cancelling the The stipulated construction of “fluid dispersion” merely restates the express definition of “fluid dispersion” from the challenged patent (although the definition is not cited or discussed in the parties’ filing). Compare Ex. 1018, Exhibit A, with Ex. 1001, 3:8–20. Similarly, the stipulated construction of “baffle” essentially parrots one sentence in the challenged patent (again, not cited or discussed in the parties’ filing). Compare Ex. 1018, Exhibit A, with Ex. 1001, 7:57–59. To the extent necessary, we determine that the complete record supports the parties’ stipulated constructions of “fluid dispersion” and “baffle,” and we apply those constructions below.” slip op. at 10
Patent outcomesUS 9,527,094 unpatentableClaim construction§ 103 obviousness§ 112 disclosurecites Phillips · NautilusPatents in suitUS 9,527,094 - Berkshire Hathaway Energy Company / Pacificorp v. Birchtech Corp.Institution deniedPTAB · May 18, 2026 · IPR2025-00278 · APJ David Cotta · IPR · Institution
The Board denied institution of Berkshire Hathaway Energy Company and PacifiCorp’s petition because it had instituted the earlier-filed IPR2025-00274 challenging the same patent.
RulingsInstitution decision- PTAB / AIA Trials › Real party in interest / privityRpi dispute resolved for petitionerDecided for petitioner
“request from Patent Owner for Director Review, finding that Patent Owner introduced “evidence sufficient to put RPI and privity at issue” and remanding with instructions to “allow discovery, narrowly tailored to resolve the RPI and privity issues” including “at least materials sufficient to clarify the evidence the Board found to be ‘ambiguous’ and to avoid the need for the Board to ‘speculate as to the nature of the redacted material.’” Paper 57 (Decision on Request for Director Review). The Director instructed that after allowing such discovery, we “should then determine on the full record whether Petitioners have met their burden of demonstrating that the Petitions are not time-barred under § 315(b), applying the framework set forth in Worlds Inc. v. Bungie, Inc., 903 F.3d 1237, 1242–44 (Fed. Cir. 2018). Concurrently herewith, we issue a decision in IPR2025- 00278 finding that Petitioner has met its burden of demonstrating that its Petition is not time-barred under 35 U.S.C. § 315(b).” slip op. at 2
- Other 314aInstitution denied discretionary otherInstitution denied
“Review Decision instructing that “if the Board determines that Petitioners met their burden to identify all RPIs in the Petitions, then the Board should maintain at most one IPR challenging each of the ’114 patent, the ’517 patent, the ’430 patent, and the ’225 patent.” Paper 79, 3. Together with its Petition in this proceeding and the proceeding in IPR2025-00274, Petitioner filed an Explanation Regarding the Necessity of Multiple Petitions. Paper 2 (“Explanation”); IPR2025-00274, Paper 2. In the Explanation, Petitioner “request[s] that, if the Board uses its discretion to institute the Petitions, the Board consider the merits of IPR2025-00274 . . . before IPR2025-00278.” Explanation, 3. Further to Petitioner’s request, we first considered the merits of IPR2025-00274. For the reasons discussed in our concurrently issued decision in IPR2025-00274, we institute inter partes review on the grounds set forth in the Petition in IPR2025-00274. Further to the Director’s instruction that we “maintain at most one IPR challenging . . . the ’114 patent,” and the Petitioner’s request that we consider the merits of IPR2025-00274 before IPR2025-00278, we deny institution of the Petition in this proceeding.” slip op. at 3
Discretionary denialPatents in suitUS 10,343,114 - Therabody, Inc. v. Hyperice IP Subco, LLCNo claims unpatentablePTAB · May 11, 2026 · PGR2025-00013 · APJ Alyssa A Finamore · PGR · Final written decision
Claims 1–16 and 18 were not shown unpatentable because the asserted prior art did not establish the claimed quick-connect system during reciprocation, and Clark was not analogous art.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“A. Level of Ordinary Skill in the Art The level of ordinary skill in the art is “a prism or lens” through which we view the prior art and the claimed invention. Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001). The prior art may reflect the level of ordinary skill in the art. Id.” slip op. at 8
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner
“During oral argument, Petitioner confirmed it would not object to the Board adopting the construction that Petitioner proposes in the district court litigation. JUDGE MARSCHALL: I think the Petitioner wouldn’t object if we adopted the construction that Petitioner proposed in the district court, especially the “designed to” construction, correct? MR. BERG: No. We wouldn’t object to that. And we think that our Petition is on all fours with that construction. Tr. 81:12–16. As Petitioner does not object to adopting its construction from the district court litigation, we construe claim element 1[e] in accordance with Petitioner’s construction from the district court litigation.” slip op. at 11
- Disclosure Requirements (§112) › Written description (Ariad)Written description adequateNot shown unpatentable
“The invention, a reciprocating massage device, is in a predictable field, namely the electro-mechanical arts. Also, there is no evidence that the recited quick-connect system is complex, even considering Patent Owner’s alleged understanding of it. Rather, Dr. Pratt testifies that many different types of connectors, whether they require alignment or not, were known. Ex. 1002 ¶¶ 54–58. Given the predictability of the electro-mechanical arts and lack of complexity of the recited quick-connect system, a low level of detail is required to satisfy the written description requirement. See RAI Strategic Holdings, Inc. v. Philip Morris Prods. S.A., 92 F.4th 1085, 1090 (Fed. Cir. 2024) (“Given the predictability of electro-mechanical inventions such as the one at issue here, and the lack of complexity of the particular claim limitation at issue—i.e., reciting the length of a heating member—‘a lower level of detail is required to satisfy the written description requirement than for unpredictable arts.’” (quoting Hologic, Inc. v. Smith & Nephew, Inc., 884 F.3d 1357, 1361 (Fed. Cir. 2018)). In view of the low level of detail required to satisfy the written description requirement, Petitioner has not persuaded us that the Specification’s example of a quick-connect system configured to secure the massaging head as the piston reciprocates fails to provide sufficient written description support for the “quick-connect system” recited in independent claims 1 and 18.” slip op. at 14
- Disclosure Requirements (§112) › Definiteness (Nautilus)DefiniteNot shown unpatentable
“Contrary to Petitioner’s assertion, the Specification provides guidance as to what amount of deviation from a perfect cylinder is still “substantially cylindrical.” The Specification describes: Quick-connect system 600 includes a piston 602 that has a hollow-end bore 608 for receiving the shaft 621 of a massaging head 620. Located within the bore 608 of piston 602 is a cylindrical seat 604. Cylindrical seat 604 retains a magnet 606. Magnet 606 is illustrated with its north pole located flush with the seat and facing toward the opening in bore 608. Massaging head 620 includes a shaft 621 having a cylindrical pocket 622 at the distal end. Located within the cylindrical pocket 622 is a magnet 624. Magnet 624 is positioned so that its south pole is located at the distal end of shaft 621. Accordingly, when the shaft 621 of massaging head 620 is slid into opening in bore 608, the magnets 606 and 624 are attracted to one another and magnetically hold massaging head 620 firmly in place. Ex. 1001, 6:57–7:3. In view of the description of quick-connect system 600, the Specification sets forth a standard for ascertaining whether the bore and the seat located within the bore are “substantially cylindrical.” To wit, the bore and the seat within the bore are “substantially cylindrical” when the massaging head and magnet are respectively received therein so that the magnet in the seat and the magnet in the pocket of the massaging head can magnetically hold the massaging head firmly in place. Furthermore, Dr. Pratt testifies that “[m]agnetic connectors comprise a magnet on at least one of the two objects to be joined. These types of connectors are ubiquitous even today for driving threaded fasteners.” Ex. 1002 ¶ 56. Dr. Pratt also testifies that a POSITA would understand how to take into account certain variances, like runout. Ex. 2033, 25:3–17. Dr. Pratt’s testimony shows that magnetic connectors are well known and that a POSITA would be able to determine whether the bore and the seat within the bore were “substantially cylindrical” for a secure connection of the massaging head. In view of the foregoing, Petitioner has not persuaded us that the claim term “substantially cylindrical” recited in claims 13–16 fails to inform, with reasonable certainty, the shapes of the bore and the structure within the bore. Petitioner has not proven, by a preponderance of the evidence, that any of claims 13–16 are unpatentable under 35 U.S.C. § 112(b) as indefinite.” slip op. at 19
Patent outcomesUS 11,938,082 not shown unpatentableClaim construction§ 103 obviousness§ 112 disclosurecites Phillips · KSR · Graham · NautilusPatents in suitUS 11,938,082 - Therabody, Inc. v. Hyperice IP Subco, LLCNo claims unpatentablePTAB · Apr 20, 2026 · PGR2024-00053 · APJ Alyssa A Finamore · PGR · Final written decision
Petitioner did not prove claims 34–38, 40, 41, 43–46, and 58–60 unpatentable under § 112(a), § 112(b), or any asserted § 103 ground.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“The parties’ proffered definitions for the level of ordinary skill in the art differ in the details of the experience a POSITA would possess. Petitioner’s definition requires experience with rotating or reciprocating mechanisms, whereas Patent Owner’s definition requires experience with devices for human use and interaction. These differences, however, do not affect our analysis of the issues in this case. For purposes of this Decision, we adopt Petitioner’s definition of level of ordinary skill in the art.” slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed petitioner constructionDecided for petitioner
“During oral argument, Petitioner confirmed it would not object to the Board adopting the construction that Petitioner proposes in the district court litigation. JUDGE MARSCHALL: I think the Petitioner wouldn’t object if we adopted the construction that Petitioner proposed in the district court, especially the “designed to” construction, correct? MR. BERG: No. We wouldn’t object to that. And we think that our Petition is on all fours with that construction. Tr. 81:12–16. As Petitioner does not object to adopting its construction from the district court litigation, we construe claim element 34[e] in accordance with Petitioner’s construction from the district court litigation.” slip op. at 10
- Disclosure Requirements (§112) › Written description (Ariad)Written description adequateNot shown unpatentable
“The invention, a reciprocating massage device, is in a predictable field, namely the electro-mechanical arts. Also, there is no evidence that the recited quick release connector is complex, even considering Patent Owner’s alleged understanding of it. Rather, Dr. Pratt testifies that a POSITA would be able to recognize a quick release connector for a particular application. According to Dr. Pratt, A person of ordinary skill in the art would consider a number of factors, depending on the context and specific application of the connector, to determine whether a connector provides a “quick release.” Such factors could include whether the connector is designed to manually and easily connect and disconnect two objects, and whether tools are necessary to do so. Other factors to be considered may be based on the specific application or operating environment. Ex. 1002 ¶ 58. Given the predictability of the electro-mechanical arts and lack of complexity of the recited quick release connector, a low level of detail is required to satisfy the written description requirement. See RAI Strategic Holdings, Inc. v. Philip Morris Prods. S.A., 92 F.4th 1085, 1090 (Fed. Cir. 2024) (“Given the predictability of electro-mechanical inventions such as the one at issue here, and the lack of complexity of the particular claim limitation at issue—i.e., reciting the length of a heating member—‘a lower level of detail is required to satisfy the written description requirement than for unpredictable arts.’” (quoting Hologic, Inc. v. Smith & Nephew, Inc., 884 F.3d 1357, 1361 (Fed. Cir. 2018)). In view of the low level of detail required to satisfy the written description requirement, Petitioner has not persuaded us that the Specification’s example of a quick release connector configured to secure the massaging head as the piston reciprocates fails to provide sufficient written description support for the “quick release connector . . . configured to secure a first massaging head while the piston reciprocates a predetermined stroke length at the first speed” recited in claim element 34[e]. 4. Conclusion for Written Description For the reasons set forth above in sections II.C.1–3, Petitioner has not persuaded us that any aspect of claim element 34[e] lacks written description support. Petitioner has not proven, by a preponderance of the evidence, that independent claim 34, as well as any of claims 35–38, 40, 41, 43–46, and 58–60 depending therefrom, are unpatentable under 35 U.S.C. § 112(a).” slip op. at 18
- Disclosure Requirements (§112) › Definiteness (Nautilus)DefiniteNot shown unpatentable
“Contrary to Petitioner’s assertion, the Specification provides guidance as to what amount of deviation from a perfect cylinder is still “substantially cylindrical.” The Specification describes that quick-connect system 600 includes two magnets with opposite poles facing each other: magnet 606 in the distal end of piston 602 and magnet 624 located in cylindrical pocket 622 of massaging head 620. Ex. 1001, 6:57–67, Figs. 6, 6A. The Specification further describes that “when the shaft 621 of massaging head 620 is slid into opening in bore 608, the magnets 606 and 624 are attracted to one another and magnetically hold massaging head 620 firmly in place.” Id. at 6:67–7:3. In view of the description of quick-connect system 600, the Specification sets forth a standard for ascertaining whether the pocket is “substantially cylindrical.” To wit, the pocket is “substantially cylindrical” when the pocket receives a magnet therein so that the magnets can magnetically hold the massaging head firmly in place. Furthermore, Dr. Pratt testifies that “[m]agnetic connectors comprise a magnet on at least one of the two objects to be joined. These types of connectors are ubiquitous even today for driving threaded fasteners.” Ex. 1002 ¶ 55. Dr. Pratt also testifies that a POSITA would understand how to take into account certain variances, like runout. Ex. 2033, 25:3–17. Dr. Pratt’s testimony shows that magnetic connectors are well known and that a POSITA would be able to determine whether the pocket was “substantially cylindrical” for a secure connection of the massaging head. In view of the foregoing, Petitioner has not persuaded us that the claim term “substantially cylindrical” recited in independent claim 34 fails to inform, with reasonable certainty, the shape of the pocket. Petitioner has not proven, by a preponderance of the evidence, that independent claim 34, as well as claims 35–38, 40, 41, 43–46, and 58–60 depending therefrom, are unpatentable under 35 U.S.C. § 112(b) as indefinite.” slip op. at 21
Patent outcomesUS 11,857,482 not shown unpatentableClaim construction§ 103 obviousness§ 112 disclosurecites PhillipsPatents in suitUS 11,857,482 - PTAB · Mar 25, 2026 · IPR2024-01380 · APJ Arthur M Peslak · IPR · Final written decision
The Board cancelled original claims 1–10 and granted substitute claims 11–19 because Petitioner did not prove claim 11 obvious over Torrence and Piepho.
RulingsFinal written decision- 112 supportGranted
“relied upon reasonably conveys to those skilled in the art that the inventor had possession of the claimed subject matter as of the filing date.” Ariad Pharms., Inc. v. Eli Lilly and Co., 598 F.3d 1336, 1351 (Fed. Cir. 2010) (en banc) (citing Vas-Cath Inc. v. Mahurkar, 935 F.2d 1555, 1562–63 (Fed. Cir. 1991)). “[T]he hallmark of written description is disclosure.” Id. “[T]he test requires an objective inquiry into the four corners of the specification from the perspective of a person of ordinary skill in the art. Based on that inquiry, the specification must describe an invention understandable to that skilled artisan and show that the inventor actually invented the invention claimed.” Id. “In order to satisfy the written description requirement, the disclosure as originally filed does not have to provide in haec verba support for the claimed subject matter at issue.” Yingbin-Nature (Guangdong) Wood Ind. Co., Ltd. v/ Int’l Trade Com’n, 535 F.3d 1322, 1334 (Fed. Cir. 2008). “[T]he level of detail required to satisfy the written description requirement varies depending on the nature and scope of the claims and on the complexity and predictability of the relevant technology.” Ariad, 598 F.3d at 1351 (citing Capon v. Eshhar, 418 F.3d 1349, 1357–58 (Fed. Cir. 2005)). “This inquiry . . . is a question of fact.” Id. (citing Ralston Purina Co. v. Far-Mar-Co, Inc., 772 F.2d 1570, 1575 (Fed. Cir. 1985)). Further, inventions in the mechanical and electrical-based arts usually involve predictable factors and can be more predictable than other fields, such as chemistry and biology. See In re Fisher, 427 F.2d 833, 839 (CCPA 1970);” slip op. at 13
- Skill levelSkill level petitioner adoptedDecided for petitioner
“C. Level of Ordinary Skill in the Art The level of ordinary skill in the art is “a prism or lens” through which we view the prior art and the claimed invention. Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001). The person of ordinary skill in the art is a hypothetical person presumed to have known the relevant art at the time of the invention. In re GPAC Inc., 57 F.3d 1573, 1579 (Fed. Cir. 1995). In determining the level of ordinary skill in the art, we may consider certain factors, including: “(1) the educational level of the inventor; (2) type of problems encountered in the art; (3) prior art solutions to those problems; (4) rapidity with which innovations are made; (5) sophistication of the technology; and (6) educational level of active workers in the field.” Best Daiichi Sankyo Co. v. Apotex, Inc., 501 F.3d 1254, 1256 (Fed. Cir. 2007)).” slip op. at 15
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“D. Claim Construction We determine that no express construction of any claim term is necessary for purposes of this Decision. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (noting that “we need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy’”) (citing Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 16
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundReasonable expectation not foundNot shown unpatentable
“[c]ombin[e] the tapered region of Piepho with the shaft of Torrence, the tapered region would extend from an uppermost extremity of the shaft.” RMTA Opp. 9. But, Petitioner concedes that neither reference discloses a tapered region extending from the uppermost extremity. Petitioner argues that Torrence’s shaft is straight (Amended RMTA Sur-reply 9) and that “[t]he tapered region of Piepho does not extend to the extreme end of the shaft.” RMTA Opp. 11 (emphasis added). Because neither Torrence nor Piepho discloses a shaft with a tapered region that “extends from an uppermost extremity of the shaft,” we find that the combination of Torrence and Piepho does not teach limitation 11[a]. We now analyze whether Petitioner provides reasoning with a rational underpinning why a person of ordinary skill in the art would have been motivated to modify Torrence with Piepho to extend Torrence’s taper from the upper extremity of its shaft. slip op. at 22
Claim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 9,827,568 - Nxtgen Toys, LLC v. Zipstring, LLCAll claims unpatentablePTAB · Feb 20, 2026 · IPR2024-01213 · APJ Richard H Marschall · IPR · Final written decision
Claims 1–4, 12, and 15–17 are unpatentable; substitute claim 27 is allowed, while substitute claims 21–26 and 28 are denied as obvious.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person having ordinary skill in the art at the time of the invention “was typically a person with a bachelor’s degree in mechanical engineering, aerospace engineering, physics, or other science or 6 Patent Owner does not rely on any objective indicia of nonobviousness in this proceeding. engineering based degree that [was] familiar with general principles of mechanics and aerodynamics with at least two years of experience in product design and development in the field of toys or other amusement type devices.” Pet. 32 (citing Ex. 1002 ¶¶ 2–6, 22–26). Patent Owner states that it submitted the following proposal for a POSITA in the related district court litigation: “[a POSITA] would have had at least a B.S. degree in Mechanical Engineering, Electrical Engineering, Aerospace Engineering, Industrial Design, Product Design, or similar field, with at least two years industry experience in one of these fields, and such POSITA would have been familiar with general principles of mechanics, fluid mechanics and aerodynamics.” PO Resp. 4–5. We note that the parties’ proposals overlap considerably, and neither party argues the inadequacy of the other party’s proposal or that any patentability issue in this case turns on the resolution of this issue. We find Petitioner’s definition consistent with the problems and solutions disclosed in the ’774 patent and prior art of record, and adopt it as our own. See, e.g., GPAC, 57 F.3d at 1579 (approving the determination of the level of ordinary skill in the art by appeal to the references of record). We would arrive at the same findings and conclusions in this Decision if we adopted Patent Owner’s proposal.” slip op. at 7
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Id. at 1312–13. Only terms in controversy need be construed, and only to the extent necessary to resolve the controversy. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). Petitioner contends that no “term requires construction to resolve the invalidity grounds presented in this Petition since the prior art renders claims 1–4, 12, and 15–17 unpatentable under any reasonable interpretation of the claims.” Pet. 7. Patent Owner argues that it “does not believe express claim constructions are necessary during this proceeding because the claims can readily be given their ordinary and customary meaning in the context of the patent at the time it was filed.” PO Resp. 5. Based on the parties’ positions and our view of the record, we need not expressly construe any claim limitations to resolve the issues in this Decision. To the extent that any implicit claim construction issues relate to the issues raised by the parties, we address them in the context of the parties’ patentability arguments below.” slip op. at 9
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentableUnpatentable
“string, and that adding Scorch’s slot removes this arguably inconvenient process by allowing insertion and removal of a string without removing and reinstalling any aspects of the housing. See Pet 85–86 (citing Ex. 1002 ¶¶ 174–175; Ex. 1007, 3:30–3:53, 6:03; Ex. 1008, 3:46–4:45); Pet. Reply 18–20 (citing in part Ex. 2002 ¶ 187 (Dr. Janét’s testimony that Wagner’s removal and reinstallation of a cover “may be viewed as an inconvenient process”)). Making insertion and removal of the string easier and quicker provides a notable advantage over Wagner’s existing device. See id. Scorch itself supports this argument and the related expert testimony because it discusses insertion and removal of strings and stated that the slot allows a user to “swap them out really quick.” Ex. 1007, 3:30–53. Petitioner also persuasively argues that a POSITA would know how to add the slot while maintaining the proper operation of the device, such as allowing insertion and removal of the string and avoiding inadvertent exiting of the string from the device. See Pet. 86–87 (citing Ex. 1002 ¶¶ 175–176; Ex. 1007, 4:00–30, Ex. 1008, 2:49–52); Pet. Reply 19, 21 (citing Ex. 1002 ¶¶ 174–176). We find Petitioner’s arguments and reasoning in support of adding Scorch’s slot to Wagner’s housing straightforward and persuasive. Patent Owner’s arguments against the combination do not directly refute Petitioner’s reasoning or cast doubt on Scorch’s statement that its slot enables “quick” insertion and removal of a string—quicker than Wagner’s method that requires removal and replacement of a cover on its housing. See PO Resp. 16–22; PO Sur-reply 14–20; Ex. 2002 ¶ 187 (acknowledging inconvenience of Wagner’s existing process for insertion and removal of a string). Patent Owner suggests that Petitioner’s proposed combination fails to take into consideration certain drawbacks such as the risk of inadvertent string exit from the housing or slot, but Petitioner expressly addresses such concerns in the Petition. See PO Resp. 18 (stating that Scorch’s slotted funnel may allow the string to “shoot out the slot” and that Scorch addresses this by adding “a bent wire” to “prevent the string from coming out the side”); PO Sur-reply 16–17; Pet. 86–87 (arguing that Wagner’s flanges would help to trap the string in place, but if not, Scorch’s additional structures could be used to restring the string and “to further reduce the risk of a string inadvertently exiting” the device). We agree with Petitioner that a POSITA would understand how to incorporate Scorch’s slot without causing inadvertent removal of the string—using structures already present in Wagner and Scorch—and the need to add such unclaimed structurers does not teach away from the combination as Patent Owner suggests. See Pet. 86–87; PO Resp. 22. We also agree with Petitioner that a POSITA would understand how to make minor modifications, if necessary, to allow insertion and removal of the string around Wagner’s flanges. See Pet. Reply 21 (citing Ex. 1002 ¶¶ 174–176).” slip op. at 26
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner
“refute Petitioner’s reasoning or cast doubt on Scorch’s statement that its slot enables “quick” insertion and removal of a string—quicker than Wagner’s method that requires removal and replacement of a cover on its housing. See PO Resp. 16–22; PO Sur-reply 14–20; Ex. 2002 ¶ 187 (acknowledging inconvenience of Wagner’s existing process for insertion and removal of a string). Patent Owner suggests that Petitioner’s proposed combination fails to take into consideration certain drawbacks such as the risk of inadvertent string exit from the housing or slot, but Petitioner expressly addresses such concerns in the Petition. See PO Resp. 18 (stating that Scorch’s slotted funnel may allow the string to “shoot out the slot” and that Scorch addresses this by adding “a bent wire” to “prevent the string from coming out the side”); PO Sur-reply 16–17; Pet. 86–87 (arguing that Wagner’s flanges would help to trap the string in place, but if not, Scorch’s additional structures could be used to restring the string and “to further reduce the risk of a string inadvertently exiting” the device). We agree with Petitioner that a POSITA would understand how to incorporate Scorch’s slot without causing inadvertent removal of the string—using structures already present in Wagner and Scorch—and the need to add such unclaimed structurers does not teach away from the combination as Patent Owner suggests. See Pet. 86–87; PO Resp. 22. We also agree with Petitioner that a POSITA would understand how to make minor modifications, if necessary, to allow insertion and removal of the string around Wagner’s flanges. See Pet. Reply 21 (citing Ex. 1002 ¶¶ 174–176). At best, Patent Owner’s arguments on this issue establish potential drawbacks in Petitioner’s proposed combination, but drawbacks alone do not defeat Petitioner’s obviousness rationale that includes readily apparent benefits. See Winner Int’l Royalty Corp. v. Wang, 202 F.3d 1340, 1349 n.8 (Fed. Cir. 2000) (“The fact that the motivating benefit comes at the expense of another benefit . . . should not nullify its use as a basis to modify the disclosure of one reference with the teachings of another.”); Medichem, S.A. v. Rolabo, S.L., 437 F.3d 1157, 1165 (Fed. Cir. 2006) (“a given course of action often has simultaneous advantages and disadvantages, and this does not necessarily obviate motivation to combine “). In addition, even if Patent Owner were correct that Wagner’s existing design works as well as Petitioner’s proposed combination, given all of the tradeoffs involved, that would not fatally undermine Petitioner’s showing. In re Fulton, 391 F.3d 1195, 1200 (Fed. Cir. 2004) (obviousness does not require that the proposed combination “is the preferred, or most desirable, combination”). On this record, Petitioner’s (and Scorch’s) stated advantages that are achieved when adding Scorch’s slot to Wagner’s housing adequately support Petitioner’s motivation to combine rationale.” slip op. at 26
Patent outcomesUS 11,674,774 unpatentableClaim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · KSR · NautilusPatents in suitUS 11,674,774 - Penumbra, Inc. v. Rapidpulse, Inc.No claims unpatentablePTAB · Feb 17, 2026 · IPR2024-01261 · APJ Jamie T Wisz · IPR · Final written decision
Claims 1–20 were not shown unpatentable because the asserted combinations did not teach the claimed predetermined cycle for controlling distal fluid flow.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“(1) a person with a B.S. in engineering or an equivalent field, with two-four years of academic or industry experience in aspiration embolectomy and thrombectomy or comparable industry experience who would, where appropriate, work or consult with others, including a physician, to develop embolectomy or thrombectomy devices; or (2) an interventional neurosurgeon with at least three years of experience developing and/or using medical devices in embolectomy or thrombectomy procedures, and who would, where appropriate, work or consult with others, including an engineer, to develop such a medical device. Pet. 11 (citing Ex. 1005 ¶ 48). Petitioner also contends that, “[a] person with less education but more relevant practical experience, or more relevant education but less practical experience, may also meet this standard.” Id. Patent Owner states that for purposes of its PO Response, it “accepts ¶ 44). We adopt Petitioner’s characterization because it is consistent with the level of skill in the art at the time of the invention as reflected by the ’402 patent and the cited prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (explaining that specific findings regarding ordinary skill level are not required “where the prior art itself reflects an appropriate level and a need for testimony is not shown” (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163 (Fed. Cir. 1985))).” slip op. at 8
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner
“specification explicitly includes sensors similar to those in the prior art in support of their argument that the claimed “predetermined cycle” must not exclude the use of such sensors. Pet. Reply 15 (citing Ex. 1001, 32:55–33:7, 40:66–41:5, 44:9–29). We reviewed the portions of the specification cited by Petitioner. We agree with Patent Owner that one excerpt discussing sensor use appears to be directed to triggering the predetermined cycle rather than causing timing changes during the cycle itself (Ex. 1001, 32:55–66) (describing use of a pressure sensor to “determine when the vacuum channel 3 is clogged by a thrombus and automatically perform the unclogging procedures described herein”), while another excerpt discusses a sensor that Petitioner that the ’402 patent discusses the use of sensors to “tune” the system and that such “tuning” can be done statically (setting the cycle timing in advance) or dynamically (adjusting the timing during the cycle itself). See Ex. 1001, 48:19–49:50. Overall, we find that these disclosures involving sensors demonstrate that sensors may be used in various ways in different embodiments. However, none of these disclosures explicitly discuss the use of sensors in conjunction with a “pre-determined cycle.” Therefore, we find that the ’402 patent specification’s discussion of “sensors” are not particularly informative as to the appropriate construction of a “predetermined cycle” and do not outweigh the other explicit disclosures of “predetermined cycle” in the patent. We next turn to the other intrinsic evidence discussed by the parties — the prosecution history. As discussed by Patent Owner, in the Notice of Allowance, the Examiner found that Garrison did not teach or suggest a “predetermined cycle” because Garrison’s controller “changed the cycle of opening and closing the valves based on feedback from sensors.” Ex. 1004, 86. We acknowledge that the patent applicant filed subsequent comments during prosecution in which they stated that they “do[] not concede that the Examiner’s characterizations of the terms of the claims and the prior art are correct.” Id. at 29. However, we agree with Patent Owner that the importance of the Examiner’s statement in the Notice of Allowance does not rely on it being an express disclaimer (a standard which it does not meet). PO Sur-reply 8. We also considered Petitioner’s contention that the Examiner’s interpretation of Garrison may have been in error (PO Resp. 16); however, even if this were true, the Examiner’s statement still provides helpful insight into how the Examiner was interpreting the term sensors to change the opening and closing of valves during a cycle was not a “predetermined cycle.” Id. at 86. In sum, we find that Patent Owner’s proposed construction is consistent with the usage of the term “predetermined cycle” in the ’402 patent specification and prosecution history. Thus, after considering all of the cited evidence, we construe “predetermined cycle” to mean that “the timing of the sequence of valve operations in the cycle is determined beforehand, i.e., fixed, rather than varying based on feedback after operation begins.”” slip op. at 14
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached
“2. Other Terms The parties also provided proposed constructions for the limitations of “[limited/limiting] to a positive amount of exit flow” and “control[ling] fluid flow in and out from the distal end of the catheter.” See Pet. 15–16; Pet. Reply 1–8; PO Resp. 22–24; PO Sur-Reply 2–6. However, having evaluated the arguments and evidence before us, we determine that construction of these terms is not necessary for purposes of this Decision. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 16
- Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableNot shown unpatentable
“We agree with Patent Owner that neither Petitioner nor Mr. Brown propose any combination of Yang and Mullins that does not include Mullins’s pressure sensor in order “to control fluid flow in and out from the distal end of the catheter.” Indeed, in addressing the “predetermined cycle” limitation, Mr. Brown contends that Mullins discloses a “cycling controller that ‘varies aspiration pressure according to sensed pressure within the catheter lumen.’” Ex.1005 ¶¶ 131–32 (citing, e.g., Ex.1008, 27:40–28:20 (“[a] novel aspect of this pump system is the incorporation of feedback into the pump algorithm in order to produce more effective pressure cycling”)). This use of a sensor to change pressure during a cycle, is not a “predetermined cycle” under our construction. combinations is its discussion of distal end flow control, not for its sensors.” Pet. Reply 17 (citing Ex. 1035 ¶ 83). However, Petitioner’s obviousness grounds rely on the combination of Yang and Mullins, especially with regard to Mullins’s disclosure of “a controller” in order “to control fluid flow in and out.” As discussed above, Mullins relies on the sensor-feedback approach in order to control flow and we find that Petitioner has not presented persuasive evidence of how the combined disclosures of Yang and Mullins would control flow without using Mullins’s sensor feedback approach. See W.L. Gore & Assocs., Inc. v. Garlock, Inc., 721 F.2d 1540, 1550 (Fed. Cir. 1983) (error to “consider[] … references in less than their entireties, i.e., in disregarding disclosures in [them] … that diverge from and teach away from the invention”). Therefore, we determine that Petitioner has not sufficiently shown that the combination of Yang and Mullins discloses or renders obvious “a controller configured to open and close the vacuum valve and the vent valve in a predetermined cycle to change a level of vacuum at the distal end of the catheter and to control fluid flow in and out from the distal end of the catheter.” Accordingly, having considered the parties’ respective evidence and arguments, we find that Petitioner has not shown by a preponderance of the evidence that claim 1 of the ’402 patent would have been unpatentable as obvious over the combination of Yang and Mullins.” slip op. at 27
Patent outcomesUS 11,406,402 not shown unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,406,402 - PTAB · Feb 10, 2026 · IPR2025-00687 · APJ Kristina M Kalan · IPR · Remand
On remand, the Board instituted IPR on claims 1–8 and 10–18 over all asserted grounds, finding a reasonable likelihood that at least one challenged claim is unpatentable.
RulingsRemand decision- RemandInstituted
“Paper 34, 1 (requesting “Director Review of the Director’s August 22, 2025 Decision Referring the Petition to the Board (‘Referral Decision’)”). Patent Owner argued that institution of IPR2025-00687 and IPR2025-00688 “should be discretionarily denied.” Id. at 5. Petitioner opposed. Paper 37. The Director granted review and found that “granting institution of two petitions that each challenge the same claims of the ’370 patent and ’218 patent 2” was an “abuse[] of discretion.” Paper 40, 1. The Director remanded the cases “to the Board panel to determine which of the two petitions challenging each of the ’370 and ’218 patents to institute.” Id. at 3. Pursuant to the Director’s instruction that we choose only one of the two petitions challenging the ’370 patent to institute, and for the reasons set forth below, we choose to institute review of the ’370 patent in this Petition, and not in IPR2025-00688.” slip op. at 3
- PTAB / AIA Trials › §315(b) time barNot time barredDecided for petitioner
“the proceeding is filed more than 1 year after the date on which the petitioner, real party in interest, or privy of the petitioner is served with a complaint alleging infringement of the patent.” 35 U.S.C. § 315(b). Petitioner bears the burden of demonstrating compliance with 35 U.S.C. § 312(a)(2) and § 315(b). See, e.g., Ventex Co., Ltd. v. Columbia Sportswear N. Am., Inc., IPR2017-00651, Paper 152 (PTAB Jan. 24, 2019)” slip op. at 9
- Skill levelSkill level petitioner adoptedDecided for petitioner
“may be considered, including the “type of problems encountered in the art; prior art solutions to those problems; rapidity with which innovations are made; sophistication of the technology; and educational level of active workers in the field.” In re GPAC, Inc., 57 F.3d 1573, 1579 (Fed. Cir. 1995). Furthermore, the prior art itself can reflect the appropriate level of ordinary skill in the art. Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 13
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner “[does] not, at this time, contend that any term requires construction,” and instead, states that “[a]ll terms have been accorded their plain and ordinary meaning.” Pet. 11 (citing Ex. 1002 ¶¶ 212–215). Patent Owner asserts that it “does not presently propose any constructions,” but discusses the Board’s claim construction in IPR2020- 00834, Paper 18, 7–8. Prelim. Resp. 7. Claim terms need only be construed to the extent necessary to resolve the controversy. Wellman, Inc. v. Eastman Chem. Co., 642 F.3d 1355, 1361 (Fed. Cir. 2011). On this record and for purposes of this Decision, we see no need to construe any claim term expressly.” slip op. at 14
Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSRPatents in suitUS 10,933,370
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.