- Aroma360, LLC v. Air Esscentials, Inc.Some claims unpatentablePTAB · Oct 6, 2026 · IPR2025-00707 · APJ Eric C Jeschke · IPR · Final written decision
Claim 5 is unpatentable over Gao-2 and over Gao-2 with Goubet; claims 1, 3, 4, and 6–8 were not shown unpatentable on any ground, and substitute claim 17 was denied.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“As noted in the Decision on Institution, Petitioner’s proposed definition appears generally consistent with the record, including the prior art. See Dec. Inst. 8 (citing In re GPAC Inc., 57 F.3d at 1579). We remove the phrase “at least” in both listed options, however, as that phrase adds ambiguity. Further, Patent Owner has not argued at trial that Petitioner’s proposal for the level of ordinary skill leads to an improper understanding of how a skilled artisan would have understood either the challenged patent or the prior art. In the analysis below, we continue to apply the level of ordinary skill in the art adopted in the Decision on Institution, as proposed by Petitioner.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Neither Petitioner nor Patent Owner propose explicit constructions for any claim terms. Pet. 16–17; PO Resp. 5–6. Based on the complete record, we need not construe explicitly any claim terms because doing so would not change the outcome of the analysis below. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 10
- Expert testimonyPetitioner expert creditedDecided for patent owner
“As an initial matter, the record here does not support any sound basis to disregard the entirety of Dr. Micklow’s Declaration for allegedly not reviewing the parties’ claim constructions. See Pet. Reply 2–3 (citing Ex. 1046, 115:15–18). Contrary to Petitioner’s argument, in the cited 11 This refers to the recitation in clauses 1F and 5F that the “diffusion assembly is disposed between said upper chamber and said lower chamber.” discussion, Dr. Micklow does not indicate that he applied an incorrect understanding of a claim term. Cf. Cordis Corp. v. Bos. Sci. Corp., 658 F.3d 1347, 1357–58 (Fed. Cir. 2011) (disregarding testimony “based on an incorrect understanding of the claim construction”), cited at Pet. Reply 1; see also Pet. Reply 3 (arguing that “Dr. Micklow’s opinion that the prior art does not render the claims obvious is premised on an interpretation of certain claim limitations that are inconsistent with both parties’ constructions” (emphasis added)). Instead, we read Dr. Micklow’s testimony as clarifying that he was not involved in claim construction at all and that, as stated, he “made [his] opinions based on what [he] read in the patents.” Ex. 1046, 112:11–12; see also id. at 115:15–18 (“I don’t know if I would even apply claim construction. I applied engineering principles to a document that had been published with the patent office.”).” slip op. at 12
- BurdenNot shown unpatentable
“referring to the same direction as the separation of the “upper chamber” and “lower chamber” (vertically in both Figure 6 of the challenged patent and Figure 1 of Goubet), we turn back now to Petitioner’s discussion of clause 1F, which includes the limitation at issue. There, Petitioner does not discuss why the “diffusion assembly” is allegedly “disposed between” the “upper chamber” and “lower chamber,” but instead, Petitioner discusses why a component of the “diffusion assembly”—the “atomizer assembly”—is allegedly “disposed between” the “upper chamber” and “lower chamber”: Pet. 39. In the end, we need not assess whether the “atomizer assembly” identified by Petitioner is “disposed between” the “upper chamber” and “lower chamber” under the proper construction of that term (which, again, we need not and do not determine here) because the “disposed between” limitation does not involve the “atomizer assembly.” Instead, we find that, by failing to address why the identified “diffusion assembly” is “disposed between” the identified “upper chamber” and “lower chamber,” Petitioner has failed to provide persuasive evidence that Goubet discloses or suggests the “disposed between” limitation. Pet. 38–39 (discussing the claim language “said diffusion assembly is disposed between said upper chamber and said lower chamber” but only discussing the location of the “atomizer assembly”); see 35 U.S.C. § 316(e) (“In an inter partes review . . . , the petitioner shall have the burden of proving a proposition of unpatentability by a preponderance of the evidence.”). For the reasons above, we find, based on the complete record, that Petitioner has not shown by a preponderance of the evidence that Goubet discloses or suggests the “disposed between” limitation.” slip op. at 22
Patent outcomesUS 10,092,918 mixedClaim construction§ 103 obviousnesscites Phillips · KSRPatents in suitUS 10,092,918 - Aroma360, LLC v. Air Esscentials, Inc.All claims unpatentablePTAB · Oct 6, 2026 · IPR2025-00706 · APJ Eric C Jeschke · IPR · Final written decision
Claims 1, 4, and 7–10 are unpatentable as obvious over Goubet and anticipated by Gao; proposed substitute claims 20 and 21 are denied as indefinite and lacking written-description support.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In the Response, Patent Owner states that it “does not dispute” the definition of one of ordinary skill in the art proposed by Petitioner, but Patent Owner “reserves the right to address [the definition] should new issues materialize.” PO Resp. 6. Patent Owner did not address this issue in the Sur-reply. As noted in the Decision on Institution, Petitioner’s proposed definition appears generally consistent with the record, including the prior art. See Dec. Inst. 8 (citing In re GPAC Inc., 57 F.3d at 1579). We remove the phrase “at least” in both listed options, however, as that phrase adds ambiguity. Further, Patent Owner has not argued at trial that Petitioner’s proposal for the level of ordinary skill leads to an improper understanding of how a skilled artisan would have understood either the challenged patent or the prior art. In the analysis below, we continue to apply the level of ordinary skill in the art adopted in the Decision on Institution, as proposed by Petitioner.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed petitioner constructionOther
“Network LLC, 929 F.3d 1350, 1357 (Fed. Cir. 2019). At first glance, the language of the limitation at issue—which, again, recites “the compressed air and the operative fluid mix together in said mixing chamber to form the fluid dispersion”—would seem to require the “fluid dispersion” (under the stipulated construction) to be fully formed in the “mixing chamber.” In other words, the language of the limitation alone would seem to support Patent Owner’s proposed construction for the “form the fluid dispersion” limitation. But the claim construction analysis does not end with consideration of the claim language alone. Next, we turn to the Specification. The Federal Circuit has said that the specification “is the single best guide to the meaning of a disputed term.” Phillips, 415 F.3d at 1315 (quoting Vitronics Corp. v. Conceptronic, Inc., 90 F.3d 1576, 1582 (Fed. Cir. 1996)). Here, the discussion in the Specification of precisely the same language as in the limitation at issue strongly supports that “to form a fluid dispersion” in the limitation at issue requires only initial mixing of the compressed air and operative fluid in the mixing chamber, with further “formation” of the ”fluid dispersion” occurring downstream of the mixing chamber: More importantly, the “predetermined amount” of compressed air and the “preselected amount” of the operable fluid are initially mixed together in the mixing chamber 226 to form a fluid dispersion. The diffusion chamber 112" is further structured to facilitate the formation of a plurality of substantially uniform droplets, as defined hereinabove, in the fluid dispersion prior to discharge from the diffusion chamber 112" through discharge port 132. Ex. 1001, 10:62–11:2 (emphasis added) (discussing Figure 6), quoted, in part, at Pet. Reply 6–710; see also Ex. 1001, 5:64–6:4 (same language, except without double primes, in a discussion of Figures 1 and 2). To be sure, certain passages in the Specification could be read to indicate that a “fluid dispersion” must be fully formed in the “mixing chamber.” See, e.g., Ex. 1001, 6:11–12 (“More in particular, the suppression chamber 232 receives the fluid dispersion from the mixing chamber 226.”); see also id. at 7:22–33, 11:39–52 (both implying that a “fluid dispersion” is formed in the mixing chamber). But the passage block quoted directly above (and the similar one bridging columns 5 and 6) more directly addresses the issue at hand—i.e., the scope of “form the fluid dispersion”—by using the same” slip op. at 13
- Expert testimonyPatent owner expert discountedMixed
“As an initial matter, the record here does not support any sound basis to disregard the entirety of Dr. Micklow’s Declaration for allegedly not reviewing the parties’ claim constructions. See Pet. Reply 2 (citing Ex. 1046, 115:15–18). Contrary to Petitioner’s argument, in the cited discussion, Dr. Micklow does not indicate that he applied an incorrect understanding of a claim term. Cf. Cordis Corp. v. Bos. Sci. Corp., 658 F.3d 1347, 1357–58 (Fed. Cir. 2011) (disregarding testimony “based on an incorrect understanding of the claim construction”), cited at Pet. Reply 1. Instead, we read Dr. Micklow’s testimony as clarifying that he was not involved in claim construction at all and that, as stated, he “made [his] opinions based on what [he] read in the patents.” Ex. 1046, 112:11–12; see also id. at 115:15–18 (“I don’t know if I would even apply claim construction. I applied engineering principles to a document that had been published with the patent office.”).” slip op. at 18
- Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable
“To satisfy its burden of proving obviousness, a petitioner cannot employ mere conclusory statements. The petitioner must instead articulate specific reasoning, based on evidence of record, to support the legal conclusion of obviousness.” In re Magnum Oil Tools Int’l, Ltd., 829 F.3d 1364, 1380 (Fed. Cir. 2016); TriVascular, Inc. v. Samuels, 812 F.3d 1056, 1066 (Fed. Cir. 2016) (“Although the KSR test is flexible, the Board ‘must still be careful not to allow hindsight reconstruction of references . . . without any explanation as to how or why the references would be combined to produce the claimed invention.’”) (citation omitted). Based on the complete record, we agree with Patent Owner that “Petitioner’s asserted motivation boils down to the conclusory statement that given Goubet and Kaiser, ‘it was well known in the field at the time of the invention that droplets of greater uniformity result in uniform droplet evaporation.’” PO Resp. 31 (quoting Pet. 59). We agree with Patent Owner that Petitioner’s discussion of the alleged reasons to combine (Pet. 59) is insufficient to support the proposed combination here. See Magnum Oil, 829 F.3d at 1380. Specifically, we are not persuaded that Kaiser’s teachings—which relate to combustion (Ex. 1014 at 43)—would have led one of ordinary skill in the art to the proposed modifications, which would allegedly “improve the smoothness (i.e., less harsh) of the aroma generated as the oil droplets evaporate in the surrounding airspace.” See Pet. 59 (emphasis added); White Pet. Decl. ¶ 251 (same); see PO Resp. 32 (“Rather, Dr. White merely describes the ability to achieve the effect as in the claimed patent, not why a [person of ordinary skill in the art] would look to the field of electrospray injection and combustion in mesoscale power-generation systems, using high-voltage electric fields to generate charged fuel droplets for controlled combustion in catalytic micro-combustors when considering atomization for scents.”). For these reasons, we determine, in light of the complete record, that Petitioner has not shown by a preponderance of the evidence that one of ordinary skill in the art at the time of the invention would have had reason to combine Goubet and Kaiser, as proposed. slip op. at 32
Patent outcomesUS 10,583,449 unpatentableClaim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · NautilusPatents in suitUS 10,583,449 - Stryker Corporation / Wright Medical Technology, Inc. v. Osteomed LLCAll claims unpatentablePTAB · May 4, 2026 · IPR2022-00189 · APJ Sheridan K Snedden · IPR · Remand
Claim 16 is unpatentable because Slater anticipates it.
RulingsRemand decision- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable
“undisputed limitations of claim 16 and find that Petitioner establishes that Slater discloses each limitation of claim 16 for the reasons provided by Petitioner. Specifically, Petitioner shows, and Patent Owner does not dispute, that Slater describes a plate with “flared hips” comprising opposing “generally parabolic wings” as recited in dependent claim 16. Pet. 28–30; Ex. 1005, Fig. 2; Ex. 1002 ¶ 106. We adopt Petitioner’s arguments and evidence as to these limitations as our own. See Pet. 28–30. Based on the foregoing, Petitioner proves by a preponderance of the evidence that Slater anticipates claim 16.” slip op. at 12
Patent outcomesUS 8,529,608 unpatentable§ 102 anticipationPatents in suitUS 8,529,608 - Stryker Corporation / Wright Medical Technology, Inc v. Osteomed LLCSome claims unpatentablePTAB · May 4, 2026 · IPR2021-01452 · APJ Sheridan K Snedden · IPR · Remand
On remand, claims 6, 8, 9, 13, and 19 are unpatentable; claims 2–5, 11, 12, 17, and 18 were not shown unpatentable over Slater or Slater and Weaver.
RulingsRemand decision- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableNot shown unpatentableMixed
“Accordingly, for the same reasons expressed by our previous decision addressing claim 8 of the ’085 patent, and the court’s analysis in Stryker, we conclude that Slater does not anticipate claims 2–5, 11, 12, 17, and 18 of the ’716 patent because Slater deliberately describes a variable angle hole that lacks a single predetermined angle—that is, Slater describes a transfixation screw hole that does not have a central axis defining the trajectory.” slip op. at 14
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentable
“In its Petition, Petitioner contends that Weaver discloses the limitations in claim 6 and that it would have been obvious to add Weaver’s features to Slater’s plate to provide a more secure fixation between the screws and the plate. Pet. 36–39; Ex. 1002 ¶¶ 188–196. Specifically, Petitioner contends that configuring Slater’s transfixation screw hole (claim 6) or at least one of Slater’s attachment points (claim 8) as a threaded screw hole to lockably engage the head of a locking screw would have been an obvious design choice “because locking screws ‘provide a high resistance to shear or torsional forces’ and reduce the incidence of screw loosening.” Pet. 39 (quoting Ex. 1009, 1:57–58); Ex. 1009, 1:46–48; Ex. 1002 ¶¶ 191– 196. Petitioner otherwise relies on its anticipation analysis for claim 1 discussed above. Pet. 36.” slip op. at 18
Patent outcomesUS 9,763,716 mixed§ 102 anticipation§ 103 obviousnessPatents in suitUS 9,763,716 - Stryker Corporation / Wright Medical Technology, Inc v. Osteomed LLCAll claims unpatentablePTAB · May 4, 2026 · IPR2022-00191 · APJ Sheridan K Snedden · IPR · Remand
On remand, the Board held claims 15 and 21 unpatentable as anticipated by Slater.
RulingsRemand decision- RemandOther
“Appeals for the Federal Circuit. The court issued its decision in Stryker Corp. v. OsteoMed LLC, No. 2023-1925, 2025 WL 2814019 (Fed. Cir. Oct. 3, 2025) (“Stryker”) (Paper 381), affirming-in-part, reversing-in-part, vacating and remanding-in-part our Final Written Decision (Paper 35) for further proceedings. In its opinion, the Federal Circuit reversed our finding of no anticipation as to independent claims 1, 10, and 16 of U.S. Patent No. 9,763,716 B2 (“the ’716 patent,” Ex. 1001), and vacated and remanded for further proceedings to evaluate whether either of dependent claims 15 and 21 is unpatentable. Stryker, slip op. at 17.” slip op. at 2
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable
“We have reviewed Petitioner’s arguments and evidence as to the undisputed limitations of claims 15 and 21 and find that Petitioner establishes that Slater discloses each limitation of claims 15 and 21 for the reasons provided by Petitioner. Specifically, Petitioner shows, and Patent Owner does not dispute, that Slater describes a plate with “flared hips” comprising opposing “generally parabolic wings” as recited in dependent claims 15 and 21. Pet. 31–33; Ex. 1005, Fig. 2; Ex. 1002 ¶ 124. We adopt Petitioner’s arguments and evidence as to these limitations as our own. See Pet. 31–33. Based on the foregoing, Petitioner proves by a preponderance of the evidence that Slater anticipates claims 15 and 21.” slip op. at 13
Patent outcomesUS 9,763,716 unpatentable§ 102 anticipationPatents in suitUS 9,763,716 - Stryker Corporation / Wright Medical Technology, Inc. v. Osteomed LLCAll claims unpatentablePTAB · May 4, 2026 · IPR2022-00190 · APJ Sheridan K Snedden · IPR · Remand
On remand, the Board determined claim 15 unpatentable as anticipated by Slater because Slater discloses every limitation, including the flared hips and opposing generally parabolic wings.
RulingsRemand decision- BurdenUnpatentable
“We have reviewed Petitioner’s arguments and evidence as to the undisputed limitations of claim 15 and find that Petitioner establishes that Slater discloses each limitation of claim 15 for the reasons provided by Petitioner. Specifically, Petitioner shows, and Patent Owner does not dispute, that Slater describes a plate with “flared hips” comprising opposing “generally parabolic wings” as recited in dependent claim 15. Pet. 30–32; Ex. 1005, Fig. 2; Ex. 1002 ¶ 119. We adopt Petitioner’s arguments and evidence as to these limitations as our own. See Pet. 28–30. Based on the foregoing, Petitioner proves by a preponderance of the evidence that Slater anticipates claim 15.” slip op. at 13
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable
“We have reviewed Petitioner’s arguments and evidence as to the undisputed limitations of claim 15 and find that Petitioner establishes that Slater discloses each limitation of claim 15 for the reasons provided by Petitioner. Specifically, Petitioner shows, and Patent Owner does not dispute, that Slater describes a plate with “flared hips” comprising opposing “generally parabolic wings” as recited in dependent claim 15. Pet. 30–32; Ex. 1005, Fig. 2; Ex. 1002 ¶ 119. We adopt Petitioner’s arguments and evidence as to these limitations as our own. See Pet. 28–30. Based on the foregoing, Petitioner proves by a preponderance of the evidence that Slater anticipates claim 15.” slip op. at 13
Patent outcomesUS 9,351,776 unpatentable§ 102 anticipationPatents in suitUS 9,351,776 - Stryker Corporation / Wright Medical Technology, Inc. v. Osteomed LLCSome claims unpatentablePTAB · May 4, 2026 · IPR2021-01450 · APJ Sheridan K Snedden · IPR · Remand
On remand, claims 6, 8–10, 14, and 17 are unpatentable; claims 2–5, 12, and 13 were not shown unpatentable, based on anticipation by Slater and obviousness over Slater and Weaver.
RulingsRemand decision- RemandMixed
“Appeals for the Federal Circuit. The court issued its decision in Stryker Corp. v. OsteoMed LLC, No. 2023-1925, 2025 WL 2814019 (Fed. Cir. Oct. 3, 2025) (“Stryker”) (Paper 49),1 affirming-in-part, reversing-in-part, vacating and remanding-in-part our Final Written Decision (Paper 46) for further proceedings. In its opinion, the Federal Circuit reversed our finding of no anticipation as to independent claims 1 and 11 of U.S. Patent No. 8,529,608 B2 (“the ’608 patent,” Ex. 1001), and vacated and remanded for further proceedings to evaluate whether dependent claims 2–6, 8–10, 12–14, and 17 (the “Remanded Claims”) are similarly unpatentable in view of Petitioner’s challenges relying on the Slater reference. Stryker, slip op. at 14–15. We have jurisdiction under 35 U.S.C. § 6. We issue this Final Written Decision on Remand pursuant to 35 U.S.C. §§ 144, 318 and 37 C.F.R. § 42.73 in an inter partes review involving Stryker Corporation and Wright Medical Technology, Inc. (collectively, “Petitioner”) and OsteoMed LLC (“Patent Owner”). For the reasons discussed below, after considering the entirety of the record in light of the Federal Circuit’s directives in Stryker, we find by a preponderance of the evidence that claims 6, 8–10, 14, and 17 are unpatentable. We also conclude that Petitioner has not demonstrated, by a preponderance of the evidence, that claims 2–5, 12, and 13 are unpatentable.” slip op. at 2
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableNot shown unpatentableMixed
“Accordingly, for the same reasons expressed by our previous decision addressing claim 8 of the ’085 patent, and the court’s analysis in Stryker, we conclude that Slater does not anticipate claims 2–5, 12, and 13 of the ’608 patent because Slater deliberately describes a variable angle hole that lacks a single predetermined angle—that is, Slater describes a transfixation screw hole that does not have a central axis defining the trajectory.” slip op. at 13
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentable
“limitations in claim 6 and that it would have been obvious to add Weaver’s features to Slater’s plate to provide a more secure fixation between the screws and the plate. Pet. 37–39; Ex. 1002 ¶¶ 161–169. Specifically, Petitioner contends that configuring Slater’s transfixation screw hole (claim 6) or at least one of Slater’s attachment points (claim 8) as a threaded screw hole to lockably engage the head of a locking screw would have been an obvious design choice “because locking screws ‘provide a high resistance to shear or torsional forces’ and reduce the incidence of screw loosening.” Pet. 39 (quoting Ex. 1009, 1:57–58); Ex. 1009, 1:46–48; Ex. 1002 ¶¶ 162– 163. Petitioner otherwise relies on its anticipation analysis for claim 1 discussed above. Pet. 37. Patent Owner raised no separate argument regarding the patentability of claims 6 and 8, instead relying solely on its argument that Slater does not anticipate independent claim 1, on which claims 6 and 8 depend. PO Resp. 46; Reply 4 (“Patent Owner does not challenge the combination of Slater and Weaver for claims 6 and 8.”). We have reviewed Petitioner’s arguments and evidence as to the undisputed limitations of claims 6 and 8 and find that Petitioner establishes that the combination of Slater and Weaver discloses all of the limitations of claims 6 and 8, and that one of ordinary skill in the art would have been motivated to combine Slater and Weaver for the reasons provided by Petitioner. We adopt Petitioner’s arguments and evidence as to these limitations as our own. See Pet. 37–39.” slip op. at 19
Patent outcomesUS 8,529,608 mixed§ 102 anticipation§ 103 obviousnessPatents in suitUS 8,529,608 - Stryker Corporation / Wright Medical Technology, Inc. v. Osteomed LLCSome claims unpatentablePTAB · May 4, 2026 · IPR2021-01451 · APJ Sheridan K Snedden · IPR · Remand
On remand, claims 6, 8, 9, and 13 were held unpatentable; claims 2–5, 11, and 12 were not shown unpatentable because Slater lacks the claimed central axis.
RulingsRemand decision- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableUnpatentableMixed
“addressing the ’085 patent and by the court’s analysis in Stryker, we conclude that Slater does not anticipate claims 2–5, 11, and 12 of the ’776 patent because Slater deliberately describes a variable angle hole that lacks a single predetermined angle—that is, Slater describes a transfixation screw hole that does not have a central axis defining the trajectory.” slip op. at 13
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentable
“In its Petition, Petitioner contends that Weaver discloses the limitations in claim 6 and that it would have been obvious to add Weaver’s features to Slater’s plate to provide a more secure fixation between the screws and the plate. Pet. 36–39; Ex. 1002 ¶¶ 169–74. Specifically, Petitioner contends that configuring Slater’s transfixation screw hole (claim 6) or at least one of Slater’s attachment points (claim 8) as a threaded screw hole to lockably engage the head of a locking screw would have been an obvious design choice “because locking screws ‘provide a high resistance to shear or torsional forces’ and reduce the incidence of screw loosening.” Pet. 39 (quoting Ex. 1009, 1:57–58); Ex. 1009, 1:46–48; Ex. 1002 ¶¶ 169– 74. Petitioner otherwise relies on its anticipation analysis for claim 1 discussed above. Pet. 36.” slip op. at 17
- RemandOther
“Appeals for the Federal Circuit. The court issued its decision in Stryker Corp. v. OsteoMed LLC, No. 2023-1925, 2025 WL 2814019 (Fed. Cir. Oct. 3, 2025) (“Stryker”) (Paper 49),1 affirming-in-part, reversing-in-part, vacating and remanding-in-part our Final Written Decision (Paper 46, “FWD”) for further proceedings. In its opinion, the Federal Circuit reversed our finding of no anticipation as to independent claims 1 and 10 of U.S. Patent 9,351,776 B2 (“the ’776 patent,” Ex. 1001), and vacated and remanded for further proceedings to evaluate whether dependent claims 2–6 and 8, 9 and 11–13 (the “Remanded Claims”) are unpatentable in view of Petitioner’s challenges relying on the Slater reference. Stryker, slip op. 14– 15.” slip op. at 2
Patent outcomesUS 9,351,776 mixed§ 102 anticipation§ 103 obviousnessPatents in suitUS 9,351,776 - Nxtgen Toys, LLC v. Zipstring, LLCAll claims unpatentablePTAB · Feb 20, 2026 · IPR2024-01213 · APJ Richard H Marschall · IPR · Final written decision
Claims 1–4, 12, and 15–17 are unpatentable; substitute claim 27 is allowed, while substitute claims 21–26 and 28 are denied as obvious.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person having ordinary skill in the art at the time of the invention “was typically a person with a bachelor’s degree in mechanical engineering, aerospace engineering, physics, or other science or 6 Patent Owner does not rely on any objective indicia of nonobviousness in this proceeding. engineering based degree that [was] familiar with general principles of mechanics and aerodynamics with at least two years of experience in product design and development in the field of toys or other amusement type devices.” Pet. 32 (citing Ex. 1002 ¶¶ 2–6, 22–26). Patent Owner states that it submitted the following proposal for a POSITA in the related district court litigation: “[a POSITA] would have had at least a B.S. degree in Mechanical Engineering, Electrical Engineering, Aerospace Engineering, Industrial Design, Product Design, or similar field, with at least two years industry experience in one of these fields, and such POSITA would have been familiar with general principles of mechanics, fluid mechanics and aerodynamics.” PO Resp. 4–5. We note that the parties’ proposals overlap considerably, and neither party argues the inadequacy of the other party’s proposal or that any patentability issue in this case turns on the resolution of this issue. We find Petitioner’s definition consistent with the problems and solutions disclosed in the ’774 patent and prior art of record, and adopt it as our own. See, e.g., GPAC, 57 F.3d at 1579 (approving the determination of the level of ordinary skill in the art by appeal to the references of record). We would arrive at the same findings and conclusions in this Decision if we adopted Patent Owner’s proposal.” slip op. at 7
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Id. at 1312–13. Only terms in controversy need be construed, and only to the extent necessary to resolve the controversy. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). Petitioner contends that no “term requires construction to resolve the invalidity grounds presented in this Petition since the prior art renders claims 1–4, 12, and 15–17 unpatentable under any reasonable interpretation of the claims.” Pet. 7. Patent Owner argues that it “does not believe express claim constructions are necessary during this proceeding because the claims can readily be given their ordinary and customary meaning in the context of the patent at the time it was filed.” PO Resp. 5. Based on the parties’ positions and our view of the record, we need not expressly construe any claim limitations to resolve the issues in this Decision. To the extent that any implicit claim construction issues relate to the issues raised by the parties, we address them in the context of the parties’ patentability arguments below.” slip op. at 9
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentableUnpatentable
“string, and that adding Scorch’s slot removes this arguably inconvenient process by allowing insertion and removal of a string without removing and reinstalling any aspects of the housing. See Pet 85–86 (citing Ex. 1002 ¶¶ 174–175; Ex. 1007, 3:30–3:53, 6:03; Ex. 1008, 3:46–4:45); Pet. Reply 18–20 (citing in part Ex. 2002 ¶ 187 (Dr. Janét’s testimony that Wagner’s removal and reinstallation of a cover “may be viewed as an inconvenient process”)). Making insertion and removal of the string easier and quicker provides a notable advantage over Wagner’s existing device. See id. Scorch itself supports this argument and the related expert testimony because it discusses insertion and removal of strings and stated that the slot allows a user to “swap them out really quick.” Ex. 1007, 3:30–53. Petitioner also persuasively argues that a POSITA would know how to add the slot while maintaining the proper operation of the device, such as allowing insertion and removal of the string and avoiding inadvertent exiting of the string from the device. See Pet. 86–87 (citing Ex. 1002 ¶¶ 175–176; Ex. 1007, 4:00–30, Ex. 1008, 2:49–52); Pet. Reply 19, 21 (citing Ex. 1002 ¶¶ 174–176). We find Petitioner’s arguments and reasoning in support of adding Scorch’s slot to Wagner’s housing straightforward and persuasive. Patent Owner’s arguments against the combination do not directly refute Petitioner’s reasoning or cast doubt on Scorch’s statement that its slot enables “quick” insertion and removal of a string—quicker than Wagner’s method that requires removal and replacement of a cover on its housing. See PO Resp. 16–22; PO Sur-reply 14–20; Ex. 2002 ¶ 187 (acknowledging inconvenience of Wagner’s existing process for insertion and removal of a string). Patent Owner suggests that Petitioner’s proposed combination fails to take into consideration certain drawbacks such as the risk of inadvertent string exit from the housing or slot, but Petitioner expressly addresses such concerns in the Petition. See PO Resp. 18 (stating that Scorch’s slotted funnel may allow the string to “shoot out the slot” and that Scorch addresses this by adding “a bent wire” to “prevent the string from coming out the side”); PO Sur-reply 16–17; Pet. 86–87 (arguing that Wagner’s flanges would help to trap the string in place, but if not, Scorch’s additional structures could be used to restring the string and “to further reduce the risk of a string inadvertently exiting” the device). We agree with Petitioner that a POSITA would understand how to incorporate Scorch’s slot without causing inadvertent removal of the string—using structures already present in Wagner and Scorch—and the need to add such unclaimed structurers does not teach away from the combination as Patent Owner suggests. See Pet. 86–87; PO Resp. 22. We also agree with Petitioner that a POSITA would understand how to make minor modifications, if necessary, to allow insertion and removal of the string around Wagner’s flanges. See Pet. Reply 21 (citing Ex. 1002 ¶¶ 174–176).” slip op. at 26
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner
“refute Petitioner’s reasoning or cast doubt on Scorch’s statement that its slot enables “quick” insertion and removal of a string—quicker than Wagner’s method that requires removal and replacement of a cover on its housing. See PO Resp. 16–22; PO Sur-reply 14–20; Ex. 2002 ¶ 187 (acknowledging inconvenience of Wagner’s existing process for insertion and removal of a string). Patent Owner suggests that Petitioner’s proposed combination fails to take into consideration certain drawbacks such as the risk of inadvertent string exit from the housing or slot, but Petitioner expressly addresses such concerns in the Petition. See PO Resp. 18 (stating that Scorch’s slotted funnel may allow the string to “shoot out the slot” and that Scorch addresses this by adding “a bent wire” to “prevent the string from coming out the side”); PO Sur-reply 16–17; Pet. 86–87 (arguing that Wagner’s flanges would help to trap the string in place, but if not, Scorch’s additional structures could be used to restring the string and “to further reduce the risk of a string inadvertently exiting” the device). We agree with Petitioner that a POSITA would understand how to incorporate Scorch’s slot without causing inadvertent removal of the string—using structures already present in Wagner and Scorch—and the need to add such unclaimed structurers does not teach away from the combination as Patent Owner suggests. See Pet. 86–87; PO Resp. 22. We also agree with Petitioner that a POSITA would understand how to make minor modifications, if necessary, to allow insertion and removal of the string around Wagner’s flanges. See Pet. Reply 21 (citing Ex. 1002 ¶¶ 174–176). At best, Patent Owner’s arguments on this issue establish potential drawbacks in Petitioner’s proposed combination, but drawbacks alone do not defeat Petitioner’s obviousness rationale that includes readily apparent benefits. See Winner Int’l Royalty Corp. v. Wang, 202 F.3d 1340, 1349 n.8 (Fed. Cir. 2000) (“The fact that the motivating benefit comes at the expense of another benefit . . . should not nullify its use as a basis to modify the disclosure of one reference with the teachings of another.”); Medichem, S.A. v. Rolabo, S.L., 437 F.3d 1157, 1165 (Fed. Cir. 2006) (“a given course of action often has simultaneous advantages and disadvantages, and this does not necessarily obviate motivation to combine “). In addition, even if Patent Owner were correct that Wagner’s existing design works as well as Petitioner’s proposed combination, given all of the tradeoffs involved, that would not fatally undermine Petitioner’s showing. In re Fulton, 391 F.3d 1195, 1200 (Fed. Cir. 2004) (obviousness does not require that the proposed combination “is the preferred, or most desirable, combination”). On this record, Petitioner’s (and Scorch’s) stated advantages that are achieved when adding Scorch’s slot to Wagner’s housing adequately support Petitioner’s motivation to combine rationale.” slip op. at 26
Patent outcomesUS 11,674,774 unpatentableClaim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · KSR · NautilusPatents in suitUS 11,674,774 - Netflix, Inc. v. Avago Technologies International Sales Pte. LimitedAll claims unpatentablePTAB · Jan 21, 2026 · IPR2021-01343 · APJ Kristen L Droesch · IPR · Remand
Claims 6, 8, 11, and 17 are unpatentable as obvious over the combined teachings of Cooper and Baldwin.
RulingsRemand decision- RemandOther
“The Federal Circuit vacated the Board’s determination as to claims 6, 8, 11, and 17 and remanded to the Board to address Petitioner’s motivationto-combine arguments for Cooper and Baldwin in view of the Board’s finding that Cooper does not teach limitation 1[d], and to address whether Cooper teaches the additional limitations of claims 6, 8, 11, and 17. See Fed. Cir. Dec. 10. The Federal Circuit faulted the Board’s conclusion as failing to provide substantive analysis of Petitioner’s motivation to combine arguments. See id. at 8. In particular, the court explained that Petitioner provided a detailed explanation of why a person of ordinary skill in the art would have been motivated to combine Cooper’s receiver teachings with Baldwin’s teachings of providing alternative streams with staggered access points and selecting the stream with the next available access point. See id. at 8–9. The court highlighted Petitioner’s following arguments: (1) a person of ordinary skill in the art would have combined the prior art according to known methods to yield predictable results; (2) combining the prior art would have been a simple substitution of one known element for another to obtain predictable results; and (3) the combination represents a choice from a finite number of identified predictable solutions with a reasonable expectation of success. See id. at 9. Accordingly, the issues before us are whether a person of ordinary skill in the art would have been motivated to combine the teachings of Cooper and Baldwin and whether Cooper teaches the additional limitations of dependent claims 6, 8, 11, and 17. See Fed. Cir. Dec. 8–10. To provide the full context for the issues before us, we first address each of the limitations of independent claims 1 and 12, and Petitioner’s reasons for combining the teachings of Cooper and Baldwin, followed by an analysis of the limitations of dependent claims 6, 8, 11, and 17.” slip op. at 8
- Skill levelSkill level board ownDecided for petitioner
“II. ANALYSIS A. Level of Ordinary Skill in the Art As previously set forth in the Final Written Decision, we determine a person of ordinary skill would have had a bachelor’s degree in electrical 3 U.S. Patent No. 7,810,124 B2, issued Oct. 5, 2010 (Ex. 1004). 4 U.S. Patent No. 7,603,689 B2, issued Oct. 13, 2009 (Ex. 1005). engineering, computer engineering, computer science, or a similar field and two years of experience in digital video signal processing or digital video streaming, which is consistent with the parties’ arguments, the ’014 patent, and the prior art of record. See Final Dec. 5.” slip op. at 5
- BurdenUnpatentable
“Based on the entire record, including the Final Written Decision, and Federal Circuit Decision, and after having considered Petitioner’s citations to Cooper, Baldwin, and Mr. Wechselberger’s testimony (Ex. 1003), we are persuaded Petitioner sets forth sufficient articulated reasoning with rational underpinning to support the conclusion that it would have been obvious to one of ordinary skill in the art to combine the teachings of Cooper and Baldwin by substituting Baldwin’s teachings of providing alternative streams with staggered access points and selecting the stream with the next available access point in place of Cooper’s teaching of identifying which alternative stream is readily available or not time-delayed to yield predictable results with the benefit of allowing a more objective-effective identification of the next available stream. See Pet. 18–23; Ex. 1003 ¶¶ 54–58; Ex. 1004, 2:58–62, 4:15–38, 5:5–23, 5:39–62, 6:5–49, 7:8–22, 17:23–45, 18:17–31, 18:57–19:3, 19:19–23, 19:41–45, 23:56–64, 24:10–19; Ex.1005, 1:25–41, 2:5–15, 6:31–35, 6:55–61, 7:40–47, 9:24–28, 10:18–24, 12:42–44; KSR, 550 U.S. at 418. e) [1e] “processing, by the receiver, the identified video information stream” slip op. at 14
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundDecided for petitioner
“Based on the entire record, including the Final Written Decision, and Federal Circuit Decision, and after having considered Petitioner’s citations to Cooper, Baldwin, and Mr. Wechselberger’s testimony (Ex. 1003), we are persuaded Petitioner sets forth sufficient articulated reasoning with rational underpinning to support the conclusion that it would have been obvious to one of ordinary skill in the art to combine the teachings of Cooper and Baldwin by substituting Baldwin’s teachings of providing alternative streams with staggered access points and selecting the stream with the next available access point in place of Cooper’s teaching of identifying which alternative stream is readily available or not time-delayed to yield predictable results with the benefit of allowing a more objective-effective identification of the next available stream. See Pet. 18–23; Ex. 1003 ¶¶ 54–58; Ex. 1004, 2:58–62, 4:15–38, 5:5–23, 5:39–62, 6:5–49, 7:8–22, 17:23–45, 18:17–31, 18:57–19:3, 19:19–23, 19:41–45, 23:56–64, 24:10–19; Ex.1005, 1:25–41, 2:5–15, 6:31–35, 6:55–61, 7:40–47, 9:24–28, 10:18–24, 12:42–44; KSR, 550 U.S. at 418. e) [1e] “processing, by the receiver, the identified video information stream” slip op. at 14
Patent outcomesUS 8,646,014 unpatentable§ 103 obviousnesscites PhillipsPatents in suitUS 8,646,014
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.