PTAB
Advanced fields
8 decisions · 541msnewest first
  • PTAB · Jan 17, 2025 · IPR2024-00597 · APJ Jon B Tornquist · IPR · Final written decision

    Claims 2–4 and 6–18 are unpatentable as obvious over Abe and Guyomard, with claims 9–10 also obvious over Iwaizono; claims 1 and 5 were not shown unpatentable.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Petitioner contends that a person of ordinary skill in the art “would have had a Master’s degree in material science, chemical engineering, chemistry, or similar field with four years of experience designing testing, and building secondary lithium batteries.” Pet. 11 (citing Ex. 1002 ¶ 51). Petitioner further contends that a person of ordinary skill in the art would have been aware of “(1) positive electrode materials, (2) negative electrode materials, (3) separators, (4) electrolytes, (5) charge-discharge parameters, and (6) protection circuits, as well as ‘battery failure modes’ such as plating and the formation of dendrites.” Id. (citing Ex. 1002 ¶¶ 50–51). Patent Owner “does not dispute Petitioner’s level of ordinary skill.” PO Resp. 17. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the disclosures of the ’641 patent and the prior art of record.” slip op. at 9

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

      “We also agree with Patent Owner that the charge cut-off voltage is not necessarily the applied voltage during charging. PO Resp. 20. Rather, depending on the charging protocol used and when in the charging cycle the voltage is applied, the applied voltage could be higher than the battery voltage. Ex. 2013; Ex. 2006 ¶ 91. For example, as discussed in more detail below with respect to the Uemura grounds, when fast charging using constant current is used and the charging rate is not slow, the applied voltage will be higher than the battery voltage when the constant current charging phase is stopped. Ex. 2006 ¶ 91; Ex. 2013. Likewise, during constant current/constant voltage charging, the applied voltage approximates the battery voltage only when the battery is nearly completely charged. Ex. 2013; Ex. 2006 ¶ 91. Thus, the applied voltage may be, but is not necessarily, the charge cut-off voltage. In view of the foregoing, we construe “charge cut-off voltage” in claims 1 and 5 as “the maximum value to which the battery is configured to be charged.” PO Resp. 18; Ex. 2008, 217:6–11; Pet. Reply 5. Contrary to Patent Owner’s arguments, however, we do not understand the phrase “configured to be charged” to necessarily represent a single voltage for the battery that is determined based on the structure and chemistry of the battery. Pet. Reply 4–5. Rather, the charge cut-off voltage is a selected potential, or voltage, of the battery or cell at the end of charging that is controlled by a circuit or device, such as a charger or control circuit within the battery. Ex. 1001, 9:50–55; Ex. 1048, 2, 7–8; Ex. 1008, 3:9–13. And, for the reasons discussed herein, the charge cut-off voltage may be, but is not necessarily, the same as the applied voltage during charging. PO Resp. 20.” slip op. at 15

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

      “charge cut-off voltage “greater than 4.2 V but less than 5.8 V” and calculating a specific or theoretic capacity “with a charge cut-off voltage limited to 4.2” (claim 1) or “with a charge cut-off voltage set at 4.2 V” (claim 5). Ex. 1001, 16:56–61, 17:6–11. Although the parties dispute the precise scope of these claim terms, the parties agree that the first use of “charge cut-off voltage” in claims 1 and 5 refers to the potential of the battery as a whole (between the cathode and the anode), and not a half-cell voltage using lithium metal as a counter electrode.10 Tr. 17:1–3 (agreeing 10 With respect to the phrase “as calculated by a theoretic capacity with a charge cut-off voltage set at 4.2 V,” the parties in fact appear to be in that the first use of “charge cut-off voltage” in claim 5 refers to a full-cell voltage); Sur-reply 5; PO Resp. 22. We need not further construe the claims to resolve the disputes between the parties. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 16

    • Expert testimonyPatent owner expert creditedDecided for patent owner

      “Given Mr. Juzkow’s unambiguous testimony that Uemura uses constant current charging that would stop when the applied voltage reached 11 The chart is reproduced from SAFT, Charging your lithium-ion batteries: 5 expert tips for a longer lifespan, (https://www.saft.com/energizing-iot/charging-your-lithium-ion-batteries-5-expert-tips-longerlifespan#:~: text=When%20the%20battery%20provides%20current,This%20restore s%20the%20battery's%20capacity). 4.3 V, as well as Dr. Yao’s persuasive testimony that Uemura’s constant charging rate is not slow, we credit the testimony of Dr. Yao that one of ordinary skill in the art would have understood that the internal voltage to which the battery of Uemura was charged is less than 4.3 V. Ex. 2006 ¶ 119. In particular, Dr. Yao persuasively testifies that one of ordinary skill in the art would have believed that the charge cut-off voltage was no more than 4.2 V, and most likely equal to “about 4 V.” Id. ¶¶ 119–122.” slip op. at 21

    Patent outcomesUS 7,749,641 mixed
    Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
    Patents in suitUS 7,749,641
  • PTAB · Jan 17, 2025 · IPR2023-01183 · APJ Jon B Tornquist · IPR · Final written decision

    Claims 2–4 and 6–18 are unpatentable as obvious over Abe and Guyomard, with claims 9 and 10 also obvious over Iwaizono; claims 1 and 5 were not shown unpatentable.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Petitioner contends that a person of ordinary skill in the art “would have had a Master’s degree in material science, chemical engineering, chemistry, or similar field with four years of experience designing testing, and building secondary lithium batteries.” Pet. 11 (citing Ex. 1002 ¶ 51). Petitioner further contends that a person of ordinary skill in the art would have been aware of “(1) positive electrode materials, (2) negative electrode materials, (3) separators, (4) electrolytes, (5) charge-discharge parameters, and (6) protection circuits, as well as ‘battery failure modes’ such as plating and the formation of dendrites.” Id. (citing Ex. 1002 ¶¶ 50–51). Patent Owner “does not dispute Petitioner’s level of ordinary skill.” PO Resp. 17. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the disclosures of the ’641 patent and the prior art of record.” slip op. at 9

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

      “constructions. First, we agree with Petitioner that the ’641 patent indicates that the charge cut-off voltage selected for a particular battery need not be a fixed property of the battery or something that is set by the design and chemistry of the battery. Consistent with this conclusion, the ’641 patent discloses that a “charging device controls the charge cut-off voltage of the single lithium-ion cell within a range from 4.3 V to 5.8 V.” Ex. 1001, 9:50– 55. This strongly suggests that the charge cut-off voltage is controlled by the charger and is not necessarily an inherent property of the battery. Patent Owner contends that this is merely an unclaimed embodiment, but the relevant disclosure states that the charging device for the “present invention” may be any type of device “with the proviso that said charging device controls the charge cut-off voltage.” Id. at 9:50–53.” slip op. at 12

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

      “charge cut-off voltage “greater than 4.2 V but less than 5.8 V” and calculating a specific or theoretic capacity “with a charge cut-off voltage limited to 4.2” (claim 1) or “with a charge cut-off voltage set at 4.2 V” (claim 5). Ex. 1001, 16:56–61, 17:6–11. Although the parties dispute the precise scope of these claim terms, the parties agree that the first use of “charge cut-off voltage” in claims 1 and 5 refers to the potential of the battery as a whole (between the cathode and the anode), and not a half-cell voltage using lithium metal as a counter electrode.10 Tr. 17:1–3 (agreeing 10 With respect to the phrase “as calculated by a theoretic capacity with a charge cut-off voltage set at 4.2 V,” the parties in fact appear to be in that the first use of “charge cut-off voltage” in claim 5 refers to a full-cell voltage); Sur-reply 5; PO Resp. 22. We need not further construe the claims to resolve the disputes between the parties. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 16

    • Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner

      “Given Mr. Juzkow’s unambiguous testimony that Uemura uses constant current charging that would stop when the applied voltage reached 11 The chart is reproduced from SAFT, Charging your lithium-ion batteries: 5 expert tips for a longer lifespan, (https://www.saft.com/energizing-iot/charging-your-lithium-ion-batteries-5-expert-tips-longerlifespan#:~: text=When%20the%20battery%20provides%20current,This%20restore s%20the%20battery's%20capacity). 4.3 V, as well as Dr. Yao’s persuasive testimony that Uemura’s constant charging rate is not slow, we credit the testimony of Dr. Yao that one of ordinary skill in the art would have understood that the internal voltage to which the battery of Uemura was charged is less than 4.3 V. Ex. 2006 ¶ 119. In particular, Dr. Yao persuasively testifies that one of ordinary skill in the art would have believed that the charge cut-off voltage was no more than 4.2 V, and most likely equal to “about 4 V.” Id. ¶¶ 119–122. Petitioner argues that because the battery of Uemura is charged “to” a maximum voltage of 4.3 V, Uemura discloses the claimed charge cut-off voltage under either Petitioner’s or Patent Owner’s construction of the term. Pet. Reply 11–12 (citing Ex. 1009 ¶ 81; Ex. 1044 ¶¶ 56–59). This argument is not persuasive because Mr. Juzkow unambiguously testified that charging in Uemura stopped when the applied voltage reached 4.3 V, and Uemura discloses that the battery was charged “at” a voltage ranging from 4.3 V to 2.0 V, not “to” such a voltage. Ex. 1009 ¶ 81; Ex. 2008, 113:2–13; Ex. 2006 ¶ 119 n.64; Sur-reply 9. In view of the foregoing, we determine that Petitioner has not demonstrated by a preponderance of the evidence that Uemura anticipates independent claims 1 and 5 of the ’641 patent.” slip op. at 21

    Patent outcomesUS 7,749,641 mixed
    Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
    Patents in suitUS 7,749,641
  • PTAB · Mar 25, 2019 · IPR2017-01869 · APJ Elizabeth M Roesel · IPR · Final written decision

    Claims 1, 4–6, 9, and 10 are unpatentable as obvious over Igarashi and Tanaka (1999); claims 2 and 7 were not shown unpatentable.

    RulingsFinal written decision
    • Skill levelSkill level patent owner adoptedDecided for patent owner

      “For purposes of our Institution Decision, we accepted the definition of a POSA provided by Dr. Bottoms. Dec. 10–11 (citing Ex. 2001 ¶ 31). Dr. Bottoms provides a “clarification” of the Board’s description, testifying that “[t]he specific industry experience would require process design experience—which is experience beyond managing fabrication equipment.” Ex. 2011 ¶ 36. Dr. Bottoms’ clarification is consistent with the level of skill reflected by the ’330 patent, which discloses process design options for making a low dielectric constant silicon nitride etch stop. Ex. 1001, 5:66-6:24. Dr. Neikirk testifies that, under Dr. Bottoms’ definition, a POSA has a higher degree of skill than under Dr. Neikirk’s definition, and the Board’s adoption of Dr. Bottoms’ definition would not change his opinions regarding obviousness. Ex. 1028 ¶ 14. We find there is little difference between the declarants’ definitions of a POSA, and the outcome of our patentability determinations would be the same, regardless of which definition we accept. For the sake of clarity, we adopt Dr. Bottoms’ definition of a POSA, including the recent clarification. Ex. 2011 ¶¶ 35, 36. We also rely on the cited prior art references as reflecting the level of ordinary skill in the art at the time of the invention. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 12

    • Expert testimonyPetitioner expert creditedPatent owner expert creditedOther

      “After reviewing the qualifications of Dr. Neikirk and Dr. Bottoms, as set forth in each witness’s declaration and curriculum vitae, we find that each of these declarants has sufficient education and experience related to the subject matter of the ’330 patent to testify regarding the perspective of a POSA at the time of the invention. Ex. 1011 ¶¶ 2, 3; Ex. 1012; Ex. 2002; Ex. 2011 ¶¶ 8–20. See Trial Practice Guide Update, 83 Fed. Reg. 39,989 (Aug. 13, 2018), available at https://go.usa.gov/xU7GP (“TPG Update”), 3 (“A person may not need to be a person of ordinary skill in the art in order to testify as an expert under Rule 702, but rather must be ‘qualified in the pertinent art.’” (quoting Sundance, Inc. v. DeMonte Fabricating Ltd., 550 F.3d 1356, 1363–64 (Fed. Cir. 2008))). D.” slip op. at 12

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

      “In the Institution Decision, we determined that it was not necessary to resolve the parties’ claim construction dispute. Dec. 9–10. Neither party challenges that determination. Petitioner contends that the asserted grounds of unpatentability apply under either party’s construction for the phrase “etch stop layer of silicon nitride.” Pet. 25 n.3. Patent Owner argues that this phrase is not limited to a layer of pure silicon nitride and allows for the presence of dopants and/or impurities. PO Resp. 8–10. Patent Owner does not, however, rely on its proposed claim construction for any patentability argument. In fact, Patent Owner acknowledges that the silicon nitride materials disclosed in the Low-K References satisfy Patent Owner’s proposed construction. PO Resp. 10. Under these circumstances, we agree with Petitioner that we do not need to resolve the parties’ claim construction dispute. Pet. Reply 2. Accordingly, consistent with the Institution Decision, we determine that we do not need to provide an express construction for any claim term for purposes of resolving the controversy. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))). B.” slip op. at 10

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

      “copper interconnects need silicon nitride films as an etch stop, but that such films have a high dielectric constant, which causes an undesirable increase in the effective dielectric constant of the interconnect structure and increased parasitic capacitance, as compared with aluminum interconnects. Ex. 1021, 829-1, 829-2; see Pet. 18; Ex. 1011 ¶¶ 92, 93. As Petitioner correctly points out (Pet. 53–54), Tanaka (1999) cites Igarashi as an example of a copper interconnect system that is degraded by parasitic capacitance due to the high permittivity (dielectric constant) of silicon nitride etch stop films. Ex. 1017, 47-1 n.1. Tanaka (1999) discloses a low dielectric constant silicon nitride etch stop film as a solution to the problem of parasitic capacitance in copper damascene interconnect structures, such as Igarashi’s. Id. at 47-1, 47-2 (“New low-k SiN film, with a permittivity of 5.4 . . . should be the solution to realize Cu damascene interconnects . . . .”). Consistent with these express disclosures, Dr. Neikirk persuasively testifies that “Igarashi identifies a need for a low-k dielectric etch stop layer” and “Tanaka (1999) meets this need.” Ex. 1011 ¶ 94; see Pet. 18 (citing Ex. 1011, § VIII.C., which contains paragraph 94 of Dr. Neikirk’s testimony). Accordingly, we find Petitioner has shown by a preponderance of the evidence that a POSA would have been motivated to use the low dielectric constant silicon nitride etch stop film of Tanaka (1999) as the etch stop layer in the interconnect system of Igarashi. Patent Owner disputes whether Petitioner has established a reasonable expectation of success for the combination of Tanaka (1999)’s low dielectric constant silicon nitride etch stop film and Igarashi’s interconnect structure. PO Resp. 65. Although the Petition does not expressly discuss whether one of ordinary skill in the art would have had a reasonable expectation of success in combining Tanaka and Igarashi to arrive at the claimed invention, Petitioner shows a very close relationship between the teachings of Tanaka (1999) and Igarashi. Pet. 12–13, 17–18, 53–62. As discussed above and argued by Petitioner, Tanaka (1999): (1) cites Igarashi as an example of a copper interconnect system that suffers from parasitic capacitance due to the high dielectric constant of silicon nitride etch stop films, and (2) discloses a low dielectric constant silicon nitride etch stop film as a solution to the parasitic capacitance problem exemplified by Igarashi. Pet. 13, 18, 53–54; Ex. 1011 ¶¶ 74–79, 88–94; Ex. 1017, 47-1 & n.1; Ex. 1021, 829-1, 829-2. Petitioner establishes a reasonable expectation of success for the combination of Tanaka (1999) and Igarashi by demonstrating a strong correlation between the problem discussed by Igarashi—the high dielectric constant of silicon nitride films when used as etch stops for copper interconnects—and the solution disclosed by Tanaka (1999)—a low dielectric constant silicon nitride film for use as an etch stop layer in copper damascene interconnect structures. In re Inland Steel Co., 265 F.3d 1354, 1364 (Fed. Cir. 2001) (“[T]he strength of the correlation between the references gives rise to a reasonable expectation of success from combining them.”).” slip op. at 27

    Patent outcomesUS 6,388,330 mixed
    Claim construction§ 103 obviousnesscites KSR · Graham
    Patents in suitUS 6,388,330
  • PTAB · Nov 7, 2018 · IPR2017-01268 · APJ Jo-Anne M Kokoski · IPR · Final written decision

    Claims 15 and 17 are unpatentable as anticipated by Ishikawa; the petitioner did not show claims 1–11, 16, and 18–20 unpatentable over Aonuma or Aonuma and Abe.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “(“POSITA”) at the time of the ’774 patent would have had “a bachelor’s degree in materials science, electrical engineering, mechanical engineering, chemistry, or a closely related field, and at least five years of experience” in industry or academic research relating to magnetic tape, or “a master’s degree or higher” in the same fields and at least three years of experience relating to magnetic tape. Pet. 13 (citing Ex. 1003 ¶ 65; Ex. 1018 ¶ 60). Patent Owner does not dispute Petitioner’s assessment in its Response, and Dr. Talke agrees that it “is reasonable.” Ex. 2026 ¶¶ 25–26. Petitioner’s assessment appears consistent with the level of ordinary skill in the art at the time of the invention as reflected in the prior art in this proceeding. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (explaining that specific findings regarding ordinary skill level are not required “where the prior art itself reflects an appropriate level and a need for testimony is not shown” (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163–64 (Fed. Cir. 1985))). Accordingly, we adopt Petitioner’s assessment of the level of ordinary skill in the art.” slip op. at 8

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

      “the broadest reasonable construction, claim terms are presumed to have their ordinary and customary meaning as understood by a person of ordinary skill in the art in the context of the entire patent disclosure. In re Translogic Tech., Inc., 504 F.3d 1249, 1257 (Fed. Cir. 2007). Only those terms in controversy need to be construed, and only to the extent necessary to resolve the controversy. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“we need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). For the purposes of the Decision on Institution, we determined that, based on the record at that time, no claim term required express construction (Dec. on Inst. 7), and we see no reason to modify that determination in light of the record developed during trial. C.” slip op. at 9

    • Expert testimonyPetitioner expert creditedMixed

      “considerably greater than Ishikawa’s stylus load of 50–300 μN (Ex. 1015 ¶ 45). The Talke Declaration does not address this discrepancy, and Dr. Talke stated during his deposition that reducing the stylus load would reduce scratching of the magnetic tape surface. Ex. 1030, 108:14–19 (“Q: Would reducing the contact pressure for the stylus instrument reduce the scratching of the magnetic tape surface by the stylus? A: Yes, it would, but you have to remember the other problem is the diameter and size of the stylus.”). Moreover, Petitioner provides evidence that it was not uncommon to use stylus-type profilometers to measure the properties of magnetic tape, even after Bhushan was published in 1996. See Reply 6. In particular, Petitioner points to Saliba,6 which describes using a stylus-type profilometer, under identical conditions to those used in Ishikawa, to measure the surface characteristics (including peak-to-valley roughness) of the backcoating of magnetic tape. Ex. 1027, 7:28–40, 57–60. Petitioner further points to Ohno,7 which also describes using “a stylus type 3D profilometer in accordance with JIS B0601” to measure the surface roughness characteristics of magnetic tape. Ex. 1028 ¶ 36; see also Ex. 1015 ¶ 45 (Ishikawa explaining that surface roughness characteristics were measured “in accordance with JIS-B0601-1994”); Ex. 1027, 7:28–39 (Saliba explaining that surface roughness characteristics where measured “in accordance with JIS-B0601-1994”). Accordingly, we are persuaded that the 6 US Patent No. 6,558,774 B1, issued May 6, 2003 (Ex. 1027). 7 U.S. Patent App. Pub. No. US 2005/0175866 A1, published Aug. 11, 2005 (Ex. 1028). evidence establishes that a stylus-type profilometer is a suitable device for measuring the surface characteristics of magnetic tape.” slip op. at 19

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

      “We agree with Petitioner that Ishikawa teaches “peak-to-valley roughness less than about 325 nm” as recited in claim 15. Pet. 24–25; Reply 5–8; Ex. 1003 ¶ 216. In particular, Ishikawa teaches a backcoating layer of a magnetic tape that has a peak-to-valley roughness “Rz of 40 to 250 nm, particularly 50 to 200 nm.” Ex. 1015 ¶ 44. Ishikawa provides five example embodiments of its magnetic tape, and reports the measurements of a number of characteristics of the backcoat layer for each example, including peak-to-valley roughness Rz. Id. ¶¶ 120–134, Table 1. Ishikawa discloses that peak-to-valley roughness Rz was measured using a stylus-type profilometer under the following conditions: Stylus: diameter: 1.5 to 2.5 μm; curvature: 60º Contact pressure: 50 to 300 μN Cut-off length: 80 μm Sampling length: 80 μm Assessment length: 400 μm Id. ¶¶ 45, 49. The reported peak-to-valley roughness Rz values for the five examples ranged from 58 to 87 nm, as shown in the annotated portion of Ishikawa Table 1 from the Petition, reproduced below: Pet. 24 (citing Ex. 1015, Table 1). The annotated portion of Ishikawa Table 1 shows the results for the measured characteristics of the backcoat layer of Examples 1–5, with the peak-to-valley roughness Rz values highlighted by a red box. Id. Because Ishikawa teaches that the backcoating layer of its magnetic tape should have a peak-to-valley roughness “Rz of 40 to 250 nm, particularly 50 to 200 nm,” and because Ishikawa presents examples of magnetic tape with backside surfaces having a peak-to-valley roughness of 87 nm or less, Ishikawa discloses “a peak-to-valley roughness less than about 325 nm” as recited in claim 15.” slip op. at 16

    Patent outcomesUS 7,029,774 mixed
    Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
    Patents in suitUS 7,029,774
  • PTAB · Dec 9, 2016 · IPR2015-01309 · APJ Jon B Tornquist · IPR · Final written decision

    Claims 1, 3, 5, 6, 10–13, 16, and 19 are unpatentable as obvious; claims 7–9, 14, and 15 were not shown unpatentable.

    RulingsFinal written decision
    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

      “Petitioner and Patent Owner propose constructions for all, or a portion of, the term “Formula I, XCF3(I), where X is a C2 unsaturated, substituted, alkyl radical.” Pet. 17–19 (proposing a construction for the term “C2 unsaturated, substituted, alkyl radical”); PO Resp. 12–15. Neither party contends, however, that express construction of this claim term, or any other term in the ’808 patent, would impact any of Petitioner’s or Patent Owner’s arguments in this proceeding. Accordingly, we determine that no claim terms require construction for purposes of this Final Written Decision. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”).” slip op. at 7

    • Skill levelSkill level patent owner adoptedDecided for patent owner

      “art. Patent Owner, relying upon the testimony of Dr. Bivens, asserts that one of ordinary skill in the art would have had either: “(1) a bachelor of science degree in a specialty area (such as chemical engineering or chemistry) and five years of work experience in developing/testing refrigerants, blowing agents, and propellants, or (2) a Ph.D. or masters of science degree and 2-3 years of work experience.” PO Resp. 12 (citing Ex. 2034 ¶¶ 21–24). Patent Owner’s identification of a person of ordinary skill in the art is uncontroverted and is consistent with the prior art of record. Accordingly, we adopt Patent Owner’s identification for purposes of this Final Written Decision. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (noting that the prior art itself may reflect the level of ordinary skill in the art).” slip op. at 8

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundMixed

      “Accordingly, we are persuaded that: (1) Petitioner has identified where every limitation of claim 1 is disclosed or suggested in the combination of Kruse, Inagaki, and Butler; (2) Petitioner has set forth reasoned explanations supported by factual underpinnings to explain why one of ordinary skill in the art, prior to the earliest filing date of the ’808 patent, would have sought to combine Kruse, Inagaki, and Butler to achieve the invention set forth in claim 1 of the ’808 patent; and (3) Petitioner has set forth reasoned arguments, supported by record evidence, to show why a person of ordinary skill in the art would have had a reasonable expectation of success in combining Kruse, Inagaki, and Butler to achieve the composition of claim 1.” slip op. at 17

    • Obviousness (§103) › Objective indicia / secondary considerations › NexusObjective indicia no nexusDecided for petitioner

      “patent met a long-felt but unresolved need or were commercially successful, we have been directed to no persuasive evidence to demonstrate these propositions. See Graham, 383 U.S. at 17–18 (noting that “long felt but unsolved needs” and commercial success may be utilized as indicia of nonobviousness). Indeed, we have been directed to no persuasive evidence that a mixture of CO2 and a fluoroalkene of claim 1 has ever been used commercially, or that such a mixture was considered by those of ordinary skill in the art to have met a long felt but previously unresolved need.9, 10 See Tr. 51:24–52:7; Pet. Reply 9 (asserting that Patent Owner “has provided no evidence, post- or pre- issuance of the ’808 patent, of the commercial advantages or uses of the claimed compositions”). With respect to Petitioner’s prior patent applications, although Patent Owner initially characterizes these applications as relating to CO2 and partially fluorinated hydrocarbons, Patent Owner later notes that these patents are directed to blends of HFO-1234yf, CO2, and R-134a. PO Resp. 44; Ex. 2024, 12 (arguing in support of patentability that “[t]he specific 9 To be relevant, Patent Owner must show that the asserted secondary considerations are attributable to “the merits of the claimed invention beyond what was readily available in the prior art.” Asyst Techs. v. Emtrak, Inc., 544 F.3d 1310, 1316 (Fed. Cir. 2008). Here, Inagaki discloses using compounds within the scope of claim 1 of the ’808 patent as refrigerants. Patent Owner presents no persuasive evidence that the addition of CO2 to the compounds of Inagaki, or the particular ranges recited in claim 1, resulted in a product that met a long felt but unresolved need or resulted in a commercially successful product beyond what was provided in Inagaki. Thus, we are also not persuaded that there is any nexus between the asserted secondary considerations and the features of claim 1 that are not disclosed in Inagaki. 10 As Patent Owner has not demonstrated any commercial use of the claim 1 compounds for any purpose, or provided evidence that those of skill in the art considered the claimed compounds to have met an unresolved need in the art, this analysis applies equally to the dependent claims of the ’808 patent, which each depend, directly or indirectly, from claim 1. combination of trans-R1234ze and R134a and CO2 simply is not suggested in Singh, let alone in the amounts defined in claim 1”). Patent Owner does not explain sufficiently why Petitioner’s arguments directed to the patentability of a blend of three compounds, utilized in specific proportions, are necessarily applicable to the combination of Kruse, Inagaki, and Butler proposed by Petitioner, or why these arguments are otherwise strong evidence of the nonobviousness of claim 1 of the ’808 patent. Based on the foregoing, and upon review of Patent Owner’s arguments as a whole, we are not persuaded that Patent Owner’s proffered objective evidence of nonobviousness is strong or tends to refute Petitioner’s arguments and evidence with respect to the obviousness of claim 1 of the ’808 patent.” slip op. at 25

    Patent outcomesUS 8,623,808 mixed
    Claim construction§ 103 obviousnesscites KSR · Graham
    Patents in suitUS 8,623,808
  • PTAB · Dec 7, 2016 · PGR2015-00013 · APJ Kevin F Turner · PGR · Final written decision

    Claims 1–4, 7–19 were held unpatentable as obvious; claims 5, 6, and 20 were not shown unpatentable over Reinhold, Walters, and Dudovich.

    RulingsFinal written decision
    • PTAB / AIA Trials › Real party in interest / privityRpi dispute resolved for petitionerDecided for petitioner

      “We found Patent Owner’s arguments and evidence to be insufficient to show a real party-in-interest issue. Discovery Order 8–10; Dec. 8. First, we found the mere existence of the relationship between Petitioner and a parent company (American Securities) to be insufficient to demonstrate a real party-in-interest issue. Discovery Order 8. In addition, we determined the evidence did not show that American Securities and Petitioner have “corporate boundaries that were inextricably intertwined.” Discovery Order 8. Second, we found the existence of common directors or employees between American Securities and Petitioner to be insufficient to show a real party-in-interest issue, unless the directors controlled or participated in the filing of the proceedings. Discovery Order 9. We found insufficient evidence that common officers between the American Securities and Petitioner were involved in the filing of the present proceedings or had the ability to direct the filing of the present proceedings. Discovery Order 9. Nor did we find persuasive evidence that American Securities provided any prior art to Petitioner in the instant proceedings. Discovery Order 9.” slip op. at 11

    • PTAB / AIA Trials › Motions to amend / substitute claimsNot reached
    • ExcludeMotion to exclude, deniedDenied

      “Patent Owner’s motion to exclude Exhibits 1013, 1014 and 1015 is denied. As Patent Owner points out, 37 C.F.R. § 42.6(a)(3) indicates that “[a]rguments must not be incorporated by reference from one document into another document.” We are not persuaded, however, that Petitioner is attempting to incorporate by reference; Exhibits 1013, 1014, and 1015 are cited by Petitioner’s declarant, not incorporated by reference. If Petitioner’s declarant or the cited exhibits contained arguments not made in a paper, we would likely ignore such arguments. In this instance, Petitioner is making of record the documents cited, which is generally laudatory, so that a reader can determine for herself that cited facts are supported. We are not persuaded that the cited exhibits are “irrelevant.” Additionally, we find no support for Patent Owner’s contention that exhibits must be cited by “papers,” and not other exhibits. Many exhibits, such as declarations, prior art references, and deposition transcripts, cite to other exhibits in normal trial practice. Accordingly, Patent Owner’s Motion to Exclude Exhibits 1013, 1014, and 1015 is denied.” slip op. at 16

    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Petitioner’s declarant, Mr. Frank Koperda, testifies that one of ordinary skill in the art would have a Bachelor of Science degree in electrical engineering, computer science, or an equivalent field, as well as at least 2–5 years of academic or industry experience in the telecommunications industry. Ex. 1002 ¶ 19; see Pet. 5 (asserting level of ordinary skill in the art). Patent Owner’s declarant, Mr. Stuart J. Lipoff, largely adopts Mr. Koperda’s level of ordinary skill in the art, adding that such artisans should have experience “in the generation of billing statements or cost accounting reports.” Ex. 2012 ¶ 33. We are not persuaded that such billing or accounting experience is necessary “to fully understand the ’280 patent disclosure.” Id. Having reviewed the prior art asserted in this proceeding (see, e.g., Exs. 1003, 1007, 1006, 1008), we also adopt the level of ordinary skill in the art employed by Petitioner’s declarant, where Patent Owner’s declarant acknowledges that his analysis would be the same under Mr. Koperda’s level of ordinary skill in the art. Ex. 2012 ¶ 34.” slip op. at 23

    Patent outcomesUS 8,855,280 mixed
    Claim construction§ 103 obviousnesscites Graham
    Patents in suitUS 8,855,280
  • PTAB · Dec 2, 2015 · IPR2014-00824 · APJ Barbara A Benoit · IPR · Final written decision

    Claims 1, 3, 4, 6, 7, 10, 19, and 20 are unpatentable over Spadaro and Hodge; claim 13 is unpatentable over Spadaro, Hodge, and Cree. Claims 2, 5, 8, 9, 11, 12, and 14–18 were …

    RulingsFinal written decision
    • BurdenDecided for patent owner

      “the burden of persuasion is on Petitioner to prove “unpatentability by a preponderance of evidence,” 35 U.S.C. § 316(e), and that burden never shifts to the Patent Owner. See id. (explaining petitioner “had the burden of 11 Dynamic Drinkware issued after the time of the trial hearing and post-hearing briefing. 11 persuasion to prove unpatentability by a preponderance of the evidence, and this burden never shifted”). Petitioner also has the initial burden of production. Id. Petitioner satisfied its burden of production by arguing in its Petition that Spadaro was prior art under § 102(e) and, in combination with one or more other prior art references, would have rendered claims 1–20 obvious at the time the invention was made under § 103(a). Pet. 4–5, 19–35.” slip op. at 11

    • Disclosure Requirements (§112) › Written description (Ariad)Not entitled to earlier dateNot shown unpatentable

      “production under § 103(c)(1), Petitioner contends it carried its burden of production to show that the ’167 patent (grandparent) sufficiently would have conveyed to one of ordinary skill in the art that the Patent Owner had possession of the claimed subject matter and, therefore, the ’260 patent is entitled to the benefit of the filing date of the ’167 patent. Reply 7. As Petitioner recognizes (Reply 6), a claim in an application is entitled, under 35 U.S.C. § 120, to the benefit of the filing date of an earlier filed application only if the disclosure of the earlier application provides support for the claims in the later application, as required by 35 U.S.C. § 112. 35 U.S.C. § 120; In re Chu, 66 F.3d 292 (Fed. Cir. 1995). Petitioner’s argument consists of a single paragraph identifying claim numbers and locations where the ’167 patent purportedly describes the subject matter of most, but not all, of the claims at issue and a citation to a single paragraph in its declarant’s supplemental declaration supporting Petitioner’s Reply. Reply 7 (listing claims 2, 8, 9, 11, and 14–18, but not listing claims 5 and 12; citing Ex. 1020 ¶ 16).” slip op. at 21

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

      “The ’260 patent does not set forth a special definition for “call application management system.” As confirmed by Dr. Forys (id.), the plain language of the claim specifies the function required to be performed by the call application management system—connecting calls responsive to 26 receiving a request to connect the call. Although Dr. Forys found Patent Owner’s proposed construction to be “reasonable,” Patent Owner’s proposed construction unnecessarily introduces the term “call processing,” which is not recited by the claim itself and on its face seems broader than the recited function of a call application management system—to connect a call. We do not agree with Patent Owner that a call application management system must perform examples of call processing described by the Specification, but not recited in the claim. Limitations from embodiments are not to be imported into the claims. See In re Van Geuns, 988 F.2d at 1184. Furthermore, we find that Patent Owner’s contention— the name “the call application management system would be understood [by one of ordinary skill in the art] to manage, from start to finish, each call placed or received at the plurality of prisons” (PO Resp. 6)—places too much weight on the term “management” without sufficiently addressing the term “application.” We credit the testimony of Petitioner’s declarant, who disagrees that call application management system is required to manage “all call processing, ‘from start to finish.’” Ex. 1020 ¶ 8. Therefore, in light of the plain language of the claim, the Specification of the ’260 patent, and according the testimony of Patent Owner’s declarant and Petitioner’s declarant appropriate weight, we construe “call application management system” to mean a system that performs the enumerated function—“connecting a call to or from the telephone terminals over a telephone carrier network responsive to receiving a request for connecting the call.”” slip op. at 26

    • Skill levelSkill level patent owner adoptedDecided for patent owner

      “The parties propose similar levels of ordinary skill in the art and do not directly challenge the other’s proposal. We consider the level of ordinary skill in the art to be reflected by the prior art of record. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001); In re GPAC Inc., 57 F.3d at 1579; In re Oelrich, 579 F.2d 86, 91 (CCPA 1978). The prior art references, like the ’260 patent, relate to telephone communication systems. See Ex. 1001, 1:60–62 (indicating the technical field relates to inmate management and call processing); Ex. 1004, 1:7–9 (indicating the field of the invention relates to the processing of voice telephone calls); Ex. 1005, 1:7–9 (indicating the field of the invention relates to telephone communication systems). In general, we adopt the areas of agreement in the parties’ proposals. Patent Owner’s proposed academic or industry experience of telephony15 systems comports with the level of ordinary skill in the art reflected in the prior art of record, which relate to telephone communication systems. Petitioner has not explained sufficiently why the broader field of communications systems is a more appropriate area of academic or industry 15 MCGRAW-HILL DICTIONARY OF SCIENTIFIC AND TECHNICAL TERMS 2112 (6th ed. 2003) (defining telephony as “[t]he transmission of speech to a distant point by means of electric signals”) (Ex. 3001). 30 experience than telephony systems. Thus, we generally adopt Patent Owner’s proposed academic or industry experience in telephony systems. Therefore, one of ordinary skill in the art would have a Bachelor of” slip op. at 30

    Patent outcomesUS 8,340,260 mixed
    Claim construction§ 103 obviousness§ 112 disclosurecites Phillips · KSR · Graham
    Patents in suitUS 8,340,260
  • Groupon, Inc. v. Blue Calypso, LLCSome claims unpatentable
    PTAB · Dec 17, 2014 · CBM2013-00033 · APJ Barbara A Benoit · CBM · Final written decision

    Claims 7-16 and 23-27 are unpatentable as anticipated by Paul; claims 1-6 and 17-22 were not shown unpatentable because Ratsimor was not a publicly accessible printed publication.

    RulingsFinal written decision
    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for patent owner

      “endorsement.” In proffering constructions, neither party provides sufficient evidence of the ordinary meaning of “bi-lateral” or “endorsement.” We determine the ordinary meaning of the terms “bi-,”7 “lateral,”8 and “endorsement”9 collectively mean “both sides giving approval.” The use of “bi-lateral endorsement” in independent claims 7 and 23 indicate that an endorsement occurs between two parties, a subscriber and an advertiser, which is consistent with its ordinary meaning of “both sides giving 7 AMERICAN HERITAGE DICTIONARY 181 (3d ed. 1992) (defining “bi-” as “1. a. Two . . . b. Both . . . c. Both sides, parts, or directions”). 8 AMERICAN HERITAGE DICTIONARY 1017 (3d ed. 1992) (defining “lateral” as “1. Of, relating to, or situated at or on the side”). 9 AMERICAN HERITAGE DICTIONARY 608 (3d ed. 1992) (defining “endorse” as “4. To give approval of or support to, especially by public statement”); id. (defining “endorsement” as “1. The act of endorsing”). 11 approval.” The ’679 patent provides an example of a bi-lateral endorsement in Figure 7a, which describes a bi-directional endorsement process between the subscriber and the advertiser, via an intermediary, during the enrollment process. Ex. 1001, col. 7, ll. 56-58. As part of an enrollment process, the advertiser decides whether to endorse a particular subscriber. Id. at col. 8, ll. 47-48. The bi-lateral endorsement is completed after the subscriber chooses at least one plan and one advertiser for endorsement. Id. at col. 8, l. 66 – col. 9, l. 3. The ’679 patent also describes examples of endorsement by an advertiser of a subscriber and endorsement by a subscriber of one or more advertisers. See id. at col. 3, ll. 39-65, col. 4, ll. 59-65. The use of bilateral endorsement in the ’679 patent is consistent with its ordinary meaning of “both sides giving approval.”” slip op. at 11

    • Claim Construction › Intrinsic evidence (Phillips canons) › Preamble limiting or notPreamble limitingDecided for patent owner

      “We agree. In general, a preamble is construed as a limitation “if it recites essential structure or steps, or if it is ‘necessary to give life, meaning, and vitality’ to the claim.” Catalina Mktg. Int’l, Inc. v. Coolsavings.com, Inc., 289 F.3d 801, 808 (Fed. Cir. 2002) (quoting Pitney Bowes, Inc. v. Hewlett-Packard Co., 182 F.3d 1298, 1305 (Fed. Cir. 1999)). When the limitations in the body of the claim “rely upon and derive antecedent basis from the preamble, then the preamble may act as a necessary component of the claimed invention.” Eaton Corp. v. Rockwell Int'l Corp., 323 F.3d 1332, 1339 (Fed. Cir. 2003). Notably, the preamble of independent claim 7 requires “a source communication device possessed by a subscriber,” “a destination communication device possessed by a recipient,” and “an advertisement.” The body of claim 7 recites “the source communication device,” “the subscriber,” “the destination communication device,” and “the 18 advertisement,” all of which rely on and derive antecedent basis from the preamble of claim 7. Similarly, the preamble of independent claim 23 recites “a first communication device,” “a second communication device,” and “a set of advertisers.” The body of claim 23 recites “the first communication device,” “the second communication device,” and “the set of advertisers.” Accordingly, we conclude that the preambles of independent claims 7 and 23 are entitled to patentable weight.” slip op. at 18

    • Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication not establishedReference not prior artNot shown unpatentable

      “As an initial matter, we note that there are gaps in Petitioner’s proffered evidence—foremost is Dr. Joshi’s lack of indication that the Ratsimor paper was downloaded or otherwise disseminated, or how persons interested and ordinarily skilled in the subject matter or art, exercising reasonable diligence, could locate the Ratsimor paper on the Departmental website or otherwise locate an issued Technical Report in November 2003. 25” slip op. at 25

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

      “Based on the above disclosures of Paul, we find that the direct e-mail campaign and a “refer-a-friend” campaign are not different methods, but are different tool options provided by the campaign manager computer program in the e-mail communications system disclosed by Paul. Accordingly, as different tool options of the campaign manager in the e-mail communications system, one of ordinary skill in the art would understand that the direct e-mail campaign tool option was to be used in conjunction with the “refer-a-friend” campaign tool option to send “refer-a-friend” e-mail message incentives to a subset of the members based on member demographic characteristics. To determine otherwise would require a finding that one of ordinary skill in the art, when reading Paul, would come to the conclusion that the only option would be to send a “refer-a-friend” e-mail to all members. We do not find that one of ordinary skill in the art would have understood Paul to be so restrictive. Rather, Paul’s disclosure of the campaign manager computer program having multiple tool options to develop marketing campaigns is analogous to a reference disclosing two functions of a word processing program—creating a document and saving a document. One skilled in the art would understand the word processing program reference to disclose how to use those functions together to create and save a document.14 Cf. Transcript 67:9 – 68:11.” slip op. at 37

    Patent outcomesUS 8,155,679 mixed
    Claim construction§ 102 anticipationcites Phillips
    Patents in suitUS 8,155,679

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.