- Ascend Elements, Inc. v. Duesenfeld GmbHInstitution deniedPTAB · Oct 10, 2025 · PGR2025-00037 · APJ Kevin W Cherry · PGR · Institution
The Board denied institution of PGR on claims 1–14 because Petitioner did not show that any challenged claim was more likely than not unpatentable.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied
“information presented in the petition filed under [35 U.S.C. §] 321 . . . demonstrates that it is more likely than not that at least 1 of the claims challenged in the petition is unpatentable.” 35 U.S.C. § 324(a). For the reasons set forth below, we determine that Petitioner has failed to demonstrate that it is more likely than not that at least one of claims 1–14 of the ’463 patent is unpatentable. Accordingly, we deny institution of a postgrant review of claims 1–14 based on the grounds set forth in the Petition.” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that one of ordinary skill in the art “would have had at least a Bachelor’s degree in electrical engineering, material science, chemical engineering, or an equivalent field, as well as at least 2 to 3 years of academic or industry experience in the recycling or processing of lithiumion batteries. Additional formal education focusing on processing of lithium batteries may substitute for practical experience and additional practical experience can substitute for less education.” Pet. 10–11. Patent Owner does not contest this definition of a person of skill in the art. See Prelim. Resp. 11. For purposes of this Decision, we adopt Petitioner’s assessment of the level of ordinary skill in the art, as, on the present record, it appears consistent with the ’463 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 8
- Expert testimonyPetitioner expert discountedPatent owner expert creditedDecided for patent owner
“distinct from “comminute[ion],” Petitioner offers only the testimony of its expert, Mr. Juzkow, who equates Tomioka’s “cutting” with “comminute[ion].” See Ex. 1003 ¶ 121. However, Mr. Juzkow provides insufficient reasoning to support his conclusion, particularly given the intrinsic and extrinsic evidence discussed above. In contrast, Patent Owner’s expert, Mr. Dantam, provides extensive reasoning, supported by citations to other evidence, to support his conclusion that Tomioka’s “dismantling” is not the claimed “comminution.” Thus, we give more weight to Mr. Dantam’s testimony than Mr. Juzkow’s testimony. Weighing this evidence all together, we find that Petitioner has failed to show that it is more likely than not that Tomioka’s teaches the claimed comminution under Petitioner’s first theory.” slip op. at 15
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundTeaching away not foundNot shown unpatentable
“obvious. Pet. 34–35. However, we agree with Patent Owner that Petitioner has also failed to show that it is more likely than not that Tomioka renders this limitation obvious. See Prelim. Resp. 28–31. To begin with, Petitioner’s contentions lack sufficient reasoning explaining why a person of ordinary skill would have modified Tomioka in the manner proposed. “[R]ejections on obviousness grounds cannot be sustained by mere conclusory statements; instead, there must be some articulated reasoning with some rational underpinning to support the legal conclusion of obviousness.” In re Kahn, 441 F.3d 977, 988 (Fed. Cir. 2006). Petitioner merely asserts that a person of ordinary skill in the art could use the roller system in place of the dismantling disclosed for the embodiments in Figures 19 and 20. On this record, we find this bare contention insufficient. actual disclosure of Tomioka. The rollers in Tomioka are used to separate the “battery body” from the “resin package enclosing the battery body,” and Tomioka specifically discloses that this technique is designed to “avoid damaging the battery body.” Ex. 1005 ¶¶ 25, 26, 29; Ex. 2011 ¶¶ 72–73. Thus, there is a significant difference between what Tomioka teaches and what Petitioner proposes to use the roller system to do. In addition, as Patent Owner points out, Tomioka specifically discloses there are risks associated with mechanically crushing battery packs, such as “risk of sparking due to residual voltage if the battery units are damaged in the process.” Ex. 1005 ¶ 5. Although we do not agree with Patent Owner that this amounts to a “teaching away,” see In re Gurley, 27 F.3d 551, 553 (Fed. Cir. 1994), we do believe that this teaching suggests a trade off that should be weighed in determining whether to make the modification, see Medichem S.A. v. Rolabo S.L., 437 F.3d 1157, 1165 (Fed. Cir. 2006). However, Petitioner has failed to account adequately, if at all, for this trade off. Thus, we find that Petitioner has failed to show that it is more likely than not that Tomioka accounts for the claimed “comminuting.”” slip op. at 15
§ 103 obviousness§ 112 disclosurecites Phillips · Graham · NautilusPatents in suitUS 12,119,463 - Apple Inc. v. Resonant Systems Inc., D/B/A/ RevelhmiAll claims unpatentablePTAB · Oct 9, 2025 · IPR2024-00698 · APJ Brian D Range · IPR · Final written decision
Claims 1–5 are unpatentable as obvious under § 103 based on the asserted combinations of Izumi, Cosper, Rossi, Ibuki, and Aldrich.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person of ordinary skill in the art (POSITA) would have had a degree in mechanical engineering, electrical engineering, physics, or a related technical field, and at least 2–3 years of experience related to the design or development of systems incorporating linear actuators; additional years of experience could substitute for the degree. Pet. 4 (citing Ex. 1003 ¶ 30–31). Patent Owner contends a POSITA would have had (1) a bachelor’s degree in electrical engineering, mechanical engineering, or a comparable field of study, and (2) at least two years of professional experience with electro-mechanical control systems, or other similarly relevant industry experience. PO Resp. 2–3. Additional relevant industry experience may compensate for lack of formal education or vice versa. Id. Patent Owner further contends this is similar to Petitioner’s POSITA contention. Id. at 3. For purposes of this Decision, we adopt Petitioner’s proposal as reasonable and consistent with the ’767 patent specification and the prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art). Our reasoning herein would be the same under Patent Owner’s similar proposal.” slip op. at 8
- Claim Construction › Intrinsic evidence (Phillips canons) › Preamble limiting or notPreamble limitingDecided for petitioner
“Claim 1, Preamble. Both parties agree that the preamble of claim 1 is limiting. PO Resp. 6. We agree that claim 1’s preamble is limiting. We also note that the parties agreed that this preamble is limiting in the District Court case. Dist. Ct. Const. 10.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for petitioner
“Because neither party asserts that construction of “driving component” or “control component” is necessary to resolve the issues before us, we decline to expressly construe these claim terms. See, e.g., Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). For clarity, because Petitioner argues that plain and ordinary meaning is appropriate and because Patent Owner does not dispute that construction, we adopt the plain and ordinary meaning of these claim terms when comparing the challenged claims to the prior art. Other claim terms. It is unnecessary for us to expressly construe other claim terms for purposes of this Decision. See, e.g., Realtime Data, LLC, 912 F.3d at 1375.” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundDecided for petitioner
“Petitioner argues that a person having ordinary skill in the art would have combined Izumi’s module to include multiple sensors in accordance with Cosper’s teachings. Pet. 15. Petitioner argues that the sensors would monitor the moving element and generate a control signal in accordance with Izumi. Id. at 15–16. Petitioner further argues that Izumi’s controller would have been implemented using a microprocessor and memory as Cosper suggests. Id. at 16. Petitioner argues three reasons why a person having ordinary skill in the art would have combined Izumi with Cosper’s teachings. Id. at 16–19. First, Petitioner argues that a person having ordinary skill in the art would have looked to Cosper as a way to further Izumi’s objective of having a sensor that detects the and controls the movement of the moving element. Id. at 16–17. Second, Petitioner argues that the combination of Izumi and Cosper would have enhanced reliability of the feedback sensors by capturing “data specific to different operating parameters.” Id. at 17–18. Third, combining the references’ teachings would “facilitat[e] implementation of software instructions” by using a microprocessor and memory. Id. at 18–19. Patent Owner does not dispute Petitioner’s rationale to combine the references’ teachings. Based on our review and consideration of the record, we determine that a preponderance of the evidence supports that a person of ordinary skill in the art would have combined the teachings of Izumi and Cosper in the manner Petitioner argues (“the Izumi-Cosper combination”).” slip op. at 17
Patent outcomesUS 8,093,767 unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 8,093,767 - Apple Inc. v. Resonant Systems Inc., D/B/A/ RevelhmiAll claims unpatentablePTAB · Oct 9, 2025 · IPR2024-00697 · APJ Brian D Range · IPR · Final written decision
Claims 1–5 are unpatentable under § 103 based on the combinations of prior art listed in the decision.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“physics, or a related technical field, and at least 2–3 years of experience related to the design or development of systems incorporating linear actuators; additional years of experience could substitute for the degree. Pet. 4 (citing Ex. 1003 ¶ 30–31). Patent Owner contends a POSITA would have had (1) a bachelor’s degree in electrical engineering, mechanical engineering, or a comparable field of study, and (2) at least two years of professional experience with electro-mechanical control systems, or other similarly relevant industry experience. PO Resp. 2–3. Additional relevant industry experience may compensate for lack of formal education or vice versa. Id. Patent Owner further contends this is similar to Petitioner’s POSITA contention and states that “Patent Owner does not believe that any of the arguments herein would change if the Board were to adopt Petitioner’s definition for the level of ordinary skill rather than Patent Owner’s.” Id. at 3. For purposes of this Decision, we adopt Petitioner’s proposal as reasonable and consistent with the ’767 patent specification and the prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art). Our reasoning herein would be the same under Patent Owner’s similar proposal.” slip op. at 9
- Claim Construction › Intrinsic evidence (Phillips canons) › Preamble limiting or notPreamble limitingDecided for petitioner
“Claim 1, Preamble. Both parties agree that the preamble of claim 1 is limiting. Pet. 6; PO Resp. 6. We agree that claim 1’s preamble is limiting. We also note that the parties agreed that this preamble is limiting in the District Court case. Dist. Ct. Const. 10.” slip op. at 10
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for petitioner
“Because neither party asserts that construction of “driving component” or “control component” is necessary to resolve the issues before us, we decline to expressly construe these claim terms. See, e.g., Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). For clarity, because Petitioner argues that plain and ordinary meaning is appropriate and because Patent Owner does not dispute that construction, we adopt the plain and ordinary meaning of these claim terms when comparing the challenged claims to the prior art. Other claim terms. It is unnecessary for us to expressly construe other claim terms for purposes of this Decision. See, e.g., Realtime Data, LLC, 912 F.3d at 1375.” slip op. at 10
- Obviousness (§103) › Analogous artAnalogous artDecided for petitioner
“Our reviewing court has stated that “[t]wo separate tests define the scope of analogous prior art: (1) whether the art is from the same field of endeavor, regardless of the problem addressed and, (2) if the reference is not within the field of the inventor's endeavor, whether the reference still is reasonably pertinent to the particular problem with which the inventor is involved.” In re Bigio, 381 F.3d 1320, 1325 (Fed. Cir. 2004) (citations and internal quotes omitted). While these two criteria are helpful in many instances, we must not lose sight of the key question at hand: what is “prior art” as that term is used in 35 U.S.C. § 103(a)? References that are “too remote to be treated as ‘prior art’” are excluded from the obviousness analysis. In re Sovish, 769 F.2d 738, 741, 226 (Fed. Cir. 1985). The non-analogous art test provides helpful insight on the underlying question of what is “prior art” within the meaning of the statute; we should not, however, be blind to the reality of the circumstances of the case before us. In re Wood, 599 F.2d 1032, 1036 (CCPA (1979). Nor should we adhere to rigid and mandatory formulas that overly limit the inquiry. KSR Int’l Co. v. Teleflex Inc., 550 U.S. 398, 419 (2007).” slip op. at 20
Patent outcomesUS 8,093,767 unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 8,093,767 - PTAB · Oct 9, 2025 · IPR2025-00847 · APJ Brian D Range · IPR · Institution
Instituted IPR on claims 1–11 because Petitioners showed a reasonable likelihood of proving at least one challenged claim unpatentable across the asserted grounds.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“unless the information presented in the petition “shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” The following findings of fact and conclusions of law are not final, but are made for the sole purpose of determining whether Petitioners meet the threshold for initiating review. Any final decision shall be based on the full trial record, including any response timely filed by Patent Owner. Any arguments not raised by Patent Owner in a timely-filed response may be deemed waived. For the reasons stated below, we determine that Petitioner has established a reasonable likelihood that it would prevail with respect to at least one claim. We hereby institute an inter partes review as to claims 1–11 of the ’847 patent based upon Petitioners’ asserted grounds of unpatentability.” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“would have had a master’s degree in electrical engineering, physics, chemistry, materials science, or a related field and three years of work experience in semiconductor manufacturing, such as, for example, in integrated circuit device (or transistor) design and/or manufacturing,” and “[a]dditional relevant education could substitute for professional experience, and significant work experience or training could substitute for formal education.” Pet. 11 (citing Ex. 1003 ¶ 38). Patent Owner does not dispute the level of ordinary skill in the art. See generally Prelim. Resp. For purposes of this Decision, we adopt Petitioner’s proposal as reasonable and consistent with the ’847 patent specification and the prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art). slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached
“Petitioner does not propose any claim constructions, except to explain that the claim 7 limitation “the spacer further comprises an offset spacer, positioned between the gate and the spacer,” is “satisfied if one layer (an ‘offset spacer’) of the claimed ‘spacer’ lies between another layer of the ‘spacer’ and the gate.” Pet. 11. Patent Owner does not dispute Petitioner’s assertions or offer any claim constructions. See generally Prelim. Resp. Because resolution of Petitioner’s proposed construction is unnecessary to our analyses for purposes of this decision, we do not address the proposal here. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). We do not discern a need to construe any other claim language at this juncture because doing so would have no effect on our analyses below of Petitioner’s asserted grounds and will not assist in resolving the present controversy between the parties. See Realtime Data, LLC, 912 F.3d at 1375.” slip op. at 8
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Instituted
“a. Claim 1 Petitioner contends that claim 1 is anticipated by Lan or, alternatively, obvious in view of Lan. Pet. 18–26. Petitioner explains how Lan teaches or suggests each recitation of claim 1, and Petitioner’s position is supported by adequate evidence for institution. Id. (citing, e.g., Ex. 1003 ¶¶ 100–125). Petitioner, for example, persuasively compares the structure of Figure 12 of Lan to each limitation of claim 1. Id. Patent Owner does not dispute Petitioner’s contentions except to argue that Lan (and the Petition’s other asserted references) “Do Not Mention, Describe, or Concern ‘Raised Epitaxial Layers.’” Prelim. Resp. 22–24. Patent Owner does not persuasively undermine Petitioner’s position.” slip op. at 13
Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 7,745,847 - Apple Inc. v. Resonant Systems, Inc.Some claims unpatentablePTAB · Oct 9, 2025 · IPR2024-00806 · APJ Norman H Beamer · IPR · Final written decision
Claims 1–8, 15–17, and 20 are unpatentable under § 103; claims 14 and 19 were not shown unpatentable because the proposed paramagnetic flux paths in Wakuda lacked adequate support.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner’s expert declarant contends that person of ordinary skill in the art (POSITA) would have had a degree in mechanical engineering, electrical engineering, physics, or a related technical field, and at least 2–3 years of experience related to the design or development of systems incorporating linear actuators; additional years of experience could substitute for the advanced-level degree. Ex. 1003 ¶ 33. Patent Owner offers “a similar level of ordinary skill in the art.” PO Resp. 3. Based on a review of the record, we adopt Petitioner’s proposed level of ordinary skill in the art because it is consistent with the evidence of record, including the asserted prior art and ’830 patent specification.” slip op. at 11
- Claim Construction › Functional claiming / §112(f) means-plus-function › Whether §112(f) applies (Williamson, nonce words)§112(f) appliesDecided for petitioner
“The parties agree that independent claims 1, 19, and 20 include means plus function limitations under 35 U.S.C. § 112 ¶ 6.8 Pet. 3–7; PO Resp. 6–14. An element in a claim for a combination may be expressed as a means . . . for performing a specified function without the recital of structure, material, or acts in support thereof, and such claim shall be construed to cover the corresponding structure, material, or acts described in the specification and equivalents thereof. 35 U.S.C. § 112 ¶ 6. In particular, the parties agree that the “driving component” and “control component” requirements of independent claims 1, 19, and 20 are means plus function limitations. Pet. 3–7; PO Resp. 6–14. Construing a means plus function limitation under 35 U.S.C. § 112 ¶ 6 involves two steps: 1) identifying the claimed function and 2) identifying in the specification the corresponding structure that performs the claimed function. Med. Instrumentation & Diagnostics Corp. v. Elekta AB, 344 F.3d 1205, 1210 (Fed. Cir. 2003); Cardiac Pacemakers, Inc. v. St. Jude Med., Inc., 296 F.3d 1106, 1119 (Fed. Cir. 2002).” slip op. at 12
- Claim Construction › Functional claiming / §112(f) means-plus-function › Corresponding structure / algorithm (indefinite if none)Term construed board ownDecided for petitioner
“Therefore, the specification clearly links the function of “control[ing] supply of power from the power supply to . . . cause the moveable component to oscillate at a frequency . . . specified by one or more stored values” at least to portions of steps 706 and 708 of the flow diagram algorithm of Figure 7A, as described above. Thus, the control component requires a microprocessor and memory with algorithmic structure including a timing algorithm or similar coding for creating a control output signal that flips to control the direction of current flow through a coil (e.g., coil 514, Fig. 5, coil 626, Fig. 6), where the coil is structure that corresponds to the recited “driving component,” as noted above.11 We adopt the District Court’s conclusion in the Apple litigation that the “control component” structure itself does not require an H-bridge switch, but only requires that the processor generates the “d” inputs to the switch; and further that the structure does not require does not require computing initial default values as specified in step 702 of Figure 7A (i.e., values not specified by a user). Ex. 3001, 30–33, 35. This is in accord with settled law 11 “Rather than using a formal timer mechanism, certain implementations may simply employ counted loops or other simple programming techniques for periodically carrying out tasks.” Ex. 1001, 7:17–20. that limits the structure to that necessary to perform the claimed function. 12 By the same token, we modify the District Court’s construction to the extent it would require, based on such steps as 706, 710, and 716, a specific order of the steps of generating the “p” and “d” values. The claims only require the control component to control the power supply to cause oscillation at a specified frequency and amplitude, but do not require the frequency value to be generated before the amplitude value, or vice versa.” slip op. at 18
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundDecided for petitioner
“to include the ability disclosed in Ramsay to allow a user to customize and store parameters associated with haptic effects, such as creating “haptic track files” that specify variations in the amplitude and frequency of the effect over time to achieve a desired effect. Pet. 46–47 (citing Ex. 1006 ¶¶ 15, 25– 28, 37; Ex. 1003 ¶¶ 192–193). Petitioner argues that this combination would have been motivated by the desire to expand the functionalities of haptic devices to allow end users to create and customize haptic effects, to provide a fuller haptic experience, and to be able to store haptic effects to save processing power compared to real-time generated effects. Id. at 47–49 (citing Ex. 1006 ¶¶ 14–15, 30, 47, 53–57; Ex. 1003 ¶¶ 194–196). Petitioner argues that this making combination would have had a reasonable expectation of success given that both references deal with linear actuators, both disclose storing frequency and amplitude values, and the combination involves routine knowledge of software techniques. Id. at 49–50 (citing Ex. 1004, 2:3–9; Ex. 1006 ¶¶ 17, 26–28; Ex. 1003 ¶¶ 197–198). Petitioner further argues that it would have been obvious to use the H-bridge switch of Rossi as part of the Gregorio actuator drive circuit 16 in the asserted Gregorio-Ramsay combination to periodically switch the polarity of drive signals to electric coil 28 of Gregorio, and thus oscillate magnet 27, under the control of a signal from processor 12 of Gregorio. Pet. 56 (citing Ex. 1003 ¶ 211). Petitioner argues that this combination would have been motivated because Gregorio does not disclose implementation details and therefore one of ordinary skill would have looked toward teachings like Rossi to fill in those details, and that an H-bridge switch was a well-known example circuit for implementing a change in “current flow direction/polarity” for “push” and “pull” actions in a system, and was a simple, cost-effective, and reliable circuit design. Id. at 56–58 (citing Ex. 1020, Abstr., Figs. 4, 6, 1:65–3:54; Ex. 1003 ¶¶ 212–217). Petitioner argues that making this combination would have had a reasonable expectation of success given that it involved known techniques through routine circuit design considerations and software instructions for generating the control signal. Id. at 58 (citing Ex. 1003 ¶ 218). Petitioner further argues that it would have been obvious to modify the Gregorio-Ramsay-Rossi combination, using the control algorithm disclosed in Aldrich, to replace the monitoring technique of Gregorio with that of Aldrich to maintain a resonance frequency by incrementing or decrementing the drive frequency. Pet. 58–59 (citing Ex. 1004, 4:22–28, 4:42–48; Ex. 1021, 2; Ex. 1003 ¶ 219). Petitioner’s expert provides implementation details of Aldrich, including that the Aldrich hill-climb technique would use a Boolean value to indicate whether the frequency was being increased, with local variables set to default values, and use integer values when processing sensor signals. Id. at 59–60 (citing Ex. 1021, 2; Ex. 1003 ¶¶ 220–222). Petitioner argues that these modifications would have been motivated to improve the Gregorio system using the Aldrich feedback algorithm for targeting a resonant frequency, given that the Gregorio approach had shortcomings that required a monitoring period with reduced haptic feedback, receiving weak EMF signals. Id. at 61–62 (citing Ex. 2004, 3:65–5:55, 5:63–65; Ex. 1021, 1–3; Ex. 1003 ¶¶ 223–227). Petitioner argues that making this combination would have had a reasonable expectation of success given that it involved known techniques for improvement to yield predictable results, readily implemented via software executed by the microprocessor. Id. at 62–63 (citing Ex. 2004, 2:44–50; Ex. 1021, 2; Ex. 1003 ¶ 229). Patent Owner does not address Petitioner’s arguments regarding the” slip op. at 27
Patent outcomesUS 9,941,830 mixedClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 9,941,830 - Apple Inc. v. Resonant Systems, Inc.All claims unpatentablePTAB · Oct 9, 2025 · IPR2025-00680 · APJ Karl D Easthom · IPR · Final written decision
Claims 2 and 3 are unpatentable under § 103 over Gregorio, Ramsay, Tierling, Rossi, and Aldrich; claim 2 is also unpatentable over Gregorio, Ramsay, Wakuda, Rossi, and Aldrich.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“would have had a degree in mechanical engineering, electrical engineering, physics, or a related technical field, and at least 2–3 years of experience related to the design or development of systems incorporating linear actuators; additional years of experience could substitute for the advanced-level degree. Ex. 1003 ¶ 30. Patent Owner offers “a similar level of ordinary skill in the art.” See PO Resp. 4. Based on a review of the record, we adopt Petitioner’s proposed level of ordinary skill in the art because it is consistent with the evidence of record, including the asserted prior art and ’337 patent specification.” slip op. at 9
- Claim Construction › Functional claiming / §112(f) means-plus-function › Whether §112(f) applies (Williamson, nonce words)§112(f) appliesDecided for petitioner
“An element in a claim for a combination may be expressed as a means . . . for performing a specified function without the recital of structure, material, or acts in support thereof, and such claim shall be construed to cover the corresponding structure, material, or acts described in the specification and equivalents thereof. 35 U.S.C. § 112 ¶ 6. In particular, the parties agree that the “driving component” and “control component” requirements of independent claim 2 are means-plus-function limitations. Pet. 2–6; PO Resp. 7. Construing a means-plus-function limitation under 35 U.S.C. § 112 ¶ 6 involves two steps: 1) identifying the claimed function and 2) identifying in the specification the corresponding structure that performs the claimed function. Med. Instrumentation & Diagnostics Corp. v. Elekta AB, 344 F.3d 1205, 1210 (Fed. Cir. 2003); Cardiac Pacemakers, Inc. v. St. Jude Med., Inc., 296 F.3d 1106, 1119 (Fed. Cir. 2002).” slip op. at 10
- Claim Construction › Functional claiming / §112(f) means-plus-function › Corresponding structure / algorithm (indefinite if none)Term construed petitioner constructionTerm construed board ownMixed
“supply of power from the power supply to . . . cause the moveable component to oscillate at a frequency . . . specified by one or more stored values” to portions of steps 706 and 708 of the flow diagram algorithm of Figure 7A, as described above. Thus, the control component requires a microprocessor and memory with algorithmic structure including a timing algorithm or similar coding for creating a control output signal that flips to control the direction of current flow through a coil (e.g., coil 514, Fig. 5, coil 626, Fig. 6), where the coil is structure that corresponds to the recited “driving component,” as noted above.10 We adopt the District Court’s conclusion in the Apple litigation that the “control component” structure itself does not require an H-bridge switch, but only requires that the processor generates the “d” inputs configured to operate a switch or other circuit; and further that the structure does not require does not require computing initial default values as specified in step 702 of Figure 7A (i.e., values not specified by a user). Ex. 3001, 30–33, 35. This is in accord with settled law that limits the structure to that necessary to 10 “Rather than using a formal timer mechanism, certain implementations may simply employ counted loops or other simple programming techniques for periodically carrying out tasks.” Ex. 1001, 7:7–10. perform the claimed function. 11 By the same token, we modify the District Court’s construction to the extent it would require, based on such steps as 706, 710, and 716, a specific order of the steps of generating the “p” and “d” values. The claims only require the control component to control the power supply to cause oscillation at a specified frequency and amplitude, but do not require the frequency value to be generated before the amplitude value, or vice versa.” slip op. at 17
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner
“The record, including testimony by Dr. Hannaford (Ex. 1003; Ex. 1049), supports Petitioner’s rationale, and shows that one of ordinary skill would have been motivated to combine Gregorio, Ramsay, and Wakuda in the manner proposed. Patent Owner does not address Petitioner’s showing for combining these references with any particularity. See generally PO Resp. We discuss below Patent Owner’s argument that Petitioner’s showing as to limitation 2.f based on the combination of Gregorio and Ramsay is conclusory.” slip op. at 34
Patent outcomesUS 8,860,337 unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 8,860,337 - Apple Inc. v. Resonant Systems, Inc.All claims unpatentablePTAB · Oct 9, 2025 · IPR2024-00807 · APJ Karl D Easthom · IPR · Final written decision
Claims 2 and 3 are unpatentable under § 103 over Gregorio, Ramsay, Tierling, Rossi, and Aldrich; claim 2 is also unpatentable over Gregorio, Ramsay, Wakuda, Rossi, and Aldrich.
RulingsFinal written decision- Claim Construction › Functional claiming / §112(f) means-plus-function › Whether §112(f) applies (Williamson, nonce words)§112(f) appliesDecided for petitioner
“The parties agree that independent claim 2 includes means-plus- function limitations under 35 U.S.C. § 112 ¶ 6.8 Pet. 2–6; PO Resp. 7–15. An element in a claim for a combination may be expressed as a means . . . for performing a specified function without the recital of structure, material, or acts in support thereof, and such claim shall be construed to cover the corresponding structure, material, or acts described in the specification and equivalents thereof. 35 U.S.C. § 112 ¶ 6. In particular, the parties agree that the “driving component” and “control component” requirements of independent claim 2 are means-plus-function limitations. Pet. 2–6; PO Resp. 7. Construing a means-plus-function limitation under 35 U.S.C. § 112 ¶ 6 involves two steps: 1) identifying the claimed function and 2) identifying in the specification the corresponding structure that performs the claimed function. Med. Instrumentation & Diagnostics Corp. v. Elekta AB, 344 F.3d 1205, 1210 (Fed. Cir. 2003); Cardiac Pacemakers, Inc. v. St. Jude Med., Inc., 296 F.3d 1106, 1119 (Fed. Cir. 2002).” slip op. at 10
- Claim Construction › Functional claiming / §112(f) means-plus-function › Corresponding structure / algorithm (indefinite if none)Term construed petitioner constructionDecided for petitioner
“1. Construction of “Driving Component” Petitioner contends that the claimed function of “driving component” is “drives the moveable component to oscillate within the housing.” Pet. 5; Ex. 2002, 2. Petitioner asserts that the corresponding structure is a coil of conductive wire 420” (Figures 4A–4G); “coil 514” (Figures 5A–5B); “coil 626” (Figure 6); “electromagnet” (Figures 10-11); “additional coils 1202 and 1204” (Figure 12); “coils 1302 and 1304” (Figure 13); “driving coils 1412 and 1414” (Figure 14); “coil 1510” (Figures 15–17); “stator coils” (Figures 24A-25). Pet. 5–6 (citing Ex. 1001, 5:2–34, 5:54–59, 6:32–35, 9:11–52, 9:64–10:22, 14:59); Ex. 2002, 2.). Patent Owner states that it “does not believe that the phrase involving a ‘driving component’ needs to be construed in order to resolve any issue in this proceeding.” PO Resp. 7. Patent Owner agreed to the above construction in the Apple Litigation, and the court adopted this construction. Ex. 2002, 2. The record supports Petitioner’s position and we adopt it.” slip op. at 11
- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner’s expert declarant contends that a person of ordinary skill in the art (POSITA) would have had a degree in mechanical engineering, electrical engineering, physics, or a related technical field, and at least 2–3 years of experience related to the design or development of systems incorporating linear actuators; additional years of experience could substitute for the advanced-level degree. Ex. 1003 ¶ 30. Patent Owner offers “a similar level of ordinary skill in the art.” See PO Resp. 4. Based on a review of the record, we adopt Petitioner’s proposed level of ordinary skill in the art because it is consistent with the evidence of record, including the asserted prior art and ’337 patent specification.” slip op. at 9
- Expert testimonyPetitioner expert creditedPatent owner expert discountedDecided for petitioner
“In contrast to Petitioner’s showing, at the passage cited by Patent Owner, Dr. Goossen, Patent Owner’s expert, does not provide a basis for his opinion that “the combined system of Gregorio-Ramsay-Rossi-Aldrich does not teach the claimed output to the power supply.” Ex. 2009 ¶ 156; PO Resp. 21 (citing Ex. 2009 ¶ 156). To the extent Dr. Goossen addresses the issue, like Patent Owner, Dr. Goossen concedes that “a POSITA would recognize in the [annotated drawing of Gregorio supplied by Petitioner] that a power supply is required that is not shown.” Ex. 2009 ¶ 116. And also like Patent Owner, Dr. Goossen concludes that Petitioner’s rationale that an “unshown power supply receives a signal from the processor is a sweeping conclusion that does not follow.” Id. For the reasons discussed above in connection with Patent Owner’s parallel arguments, this testimony is conclusory and unsupported. Primarily, it does not adequately address Petitioner’s showing and Dr. Hannaford’s testimony, discussed above, which relies on Gregorio’s statement that “[p]rocessor 12 outputs the control signals to drive circuit 26 which includes electronic components and circuitry used to supply LRA 18 with the required electrical current and voltage to cause the desired haptic effects.” Ex. 1004, 2:36–39 (emphases added). Dr. Goossen and Patent Owner also do not address the initial finding in the Institution Decision that “[t]he ’337 patent does not disclose any detail or structure for the controllable power supply, indicating that such a controllable power supply was well-known.” Inst. Dec. 30 (citing Ex. 1001, 6:33–35 (“The power supply 612 receives a control input 624 from the CPU to control the current supplied to the H-bridge switch for transfer to the coil 626.”)).16 And while Dr. Goossen contends that Dr. Hannaford’s reliance on Ramsay to further suggest control of the power supply is conclusory because “Dr. Hannaford’s statement about ‘the current provided from a power supply to the driving component’ has nothing to do with Ramsay’s disclosure,’” Dr. Goossen addresses Ramsay and Gregorio in isolation, without adequately addressing the combination, specifically where Gregorio teaches or suggests controlling a power supply in order to provide desired LRA amplitude and frequency haptic effects, which is in line with Ramsay’s teaching of user-customizable parameters to control amplitude and frequency for the same purpose. See Ex. 2009 ¶ 126; Pet. 53–54 (summarized above). Therefore, the Petition shows persuasively that Gregorio’s processor controls Gregorio’s power supply to provide power to its haptic unit or that such power supply control would have been obvious in view of Ramsay in order to allow a user to control the desired haptic effect.” slip op. at 41
Patent outcomesUS 8,860,337 unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 8,860,337 - Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing deniedPTAB · Oct 7, 2025 · IPR2024-01462 · APJ Jo-Anne M Kokoski · IPR · Rehearing
The Board denied Solus’s rehearing request, leaving institution denied for claims 1–8 because the petition did not adequately show motivation to combine Hanafusa and Dobashi.
RulingsRehearing decision- RehearingRehearing, deniedDenied
“of the decision de novo, but instead review the decision for an abuse of discretion. 37 C.F.R. § 42.71(c). An abuse of discretion may be determined “if a decision is based on an erroneous interpretation of law, if a factual finding is not supported by substantial evidence, or if the decision represents” slip op. at 2
- Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable
“In particular, neither Petitioner nor Dr. Josefowicz adequately explain why a POSITA looking for ways to make Hanafusa’s surface roughness low-profile would look to methods to achieve Dobashi’s RSm values. Dobashi teaches that because RSm “can be adopted as the period of waviness, RSm can also be used as an indicator for judgment of the surface.” Ex. 1005, 2:66–3:1, 6:23–26. Dobashi explains that waviness is “an indicator for determining whether the fine pattern forming performance is good or bad,” and “[t]he surface has small waviness and is smooth when RSm is large, and the surface has large waviness Dobashi also teaches that surface roughness Rzjis is used as a low-profile indicator. Ex. 1005, 2:66–3:1. Dobashi, therefore, teaches that RSm is an indicator of surface waviness, which Dobashi explains is different than surface roughness. Id. at 2:66– 3:3, 6:23–29. Given these teachings in Dobashi, neither Petitioner nor Dr. Josefowicz sufficiently explains how or why a POSITA would have been motivated to implement Dobashi’s RSm values to make Hanafusa’s surface roughness low-profile. See Pet. 10–12; Ex. 1003 ¶¶ 46–52.” slip op. at 4
§ 103 obviousnessPatents in suitUS 11,346,014 - Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing deniedPTAB · Oct 7, 2025 · IPR2024-01461 · APJ Jo-Anne M Kokoski · IPR · Rehearing
The Board denied rehearing and left in place its denial of institution because Petitioner did not show that claims 1–10 were likely obvious over the asserted combinations.
RulingsRehearing decision- RehearingRehearing, deniedDenied
“II. STANDARD OF REVIEW When rehearing a decision on institution, we do not review the merits of the decision de novo, but instead review the decision for an abuse of discretion. 37 C.F.R. § 42.71(c). An abuse of discretion may be determined “if a decision is based on an erroneous interpretation of law, if a factual finding is not supported by substantial evidence, or if the decision represents an unreasonable judgment in weighing relevant factors.” Arnold Partnership v. Dudas, 362 F.3d 1338, 1340 (Fed. Cir. 2004) (citing In re 1 US 2013/0108922 A1, published May 2, 2013 (Ex. 1004, “Shinozaki”). 2 G. Khatibi, Temperature Dependent Elastic and Thermal Properties of Thin Copper Foils, Copper; Proceedings of the International Conference Copper ’06 (2006) (Ex. 1006, “Khatibi”). 3 Korean Patent Pub. No. 10-2012-0003485, published Jan. 10, 2012 (Ex. 1013; Ex. 1014 (English translation), “Toshio”). 4 US 2013/0108887 A1, published May 2, 2013 (Ex. 1012, “Kim”). 5 Griesi, M.B., Characterization of Electrodeposited Copper Foil Surface Roughness for Accurate Conductor Power Loss Modeling (2014) (Master’s Thesis, University of South Carolina) (Ex. 1015, “Griesi”). rehearing has the burden to show that the decision should be modified. 37 C.F.R. § 42.71(d). Additionally, the request for rehearing “must specifically identify all matters the party believes the Board misapprehended or overlooked, and the place where each matter was previously addressed in a motion, an opposition, or a reply.” Id.” slip op. at 2
- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Not shown unpatentable
“For example, Dr. Randall does not provide adequate explanation or objective evidence to support his opinion that Khatibi’s use of a laser speckle based dilatometer instead of the claimed thermomechanical analyzer “is unlikely to significantly impact the CTE[6] value” because “variations in equipment and a heating speed of 5° C/min would not significantly alter the results.” Ex. 1003 ¶ 58. In particular, Dr. Randall neither explains what constitutes a “significant” impact on CTE, nor provides objective evidence to support his contention that equipment variations and heating differences would not “significantly alter” the resulting measurements. And although Dr. Randall opines that “the heating rate (5°C per minute) is typical for certain devices” such as a thermomechanical analyzer or dilatometer, and “[t]ypically, these devices use temperature ramp rates between 2°C and 20°C per minutes, so the ‘5° C./min’ recited in [1d] is common and should not drastically affect the measurement results,” Dr. Randall fails to point us to any evidence showing that these temperatures are “typical” or that the claimed heating rate is “common.” Id. ¶ 59 (emphases added).” slip op. at 4
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable
“Petitioner, however, does not adequately explain why a POSITA would have been motivated to modify Kim’s copper foil surface to have a Pc value of 19.2 as reported in Griesi. In particular, neither Petitioner nor Dr. Randall points us to, nor do we discern, any teaching in Griesi that a peak count of 19.2 provides any particular benefits or properties that would have lead a POSITA to modify Kim’s copper foil surface as Petitioner proposes. Instead, Petitioner’s arguments that a POSITA would have been motivated to modify Kim’s copper foil surface with Griesi’s peak count patent itself. See KSR Int’l Co. v. Teleflex Inc., 550 U.S. 398, 421 (2007) (stating that the fact finder must be aware “of the distortion caused by hindsight bias and must be cautious of arguments reliant upon ex post reasoning”). It was Petitioner’s burden to establish that the combined teachings Kim and Griesi disclose limitation [1g] as proposed. We are not persuaded that we misapprehended Petitioner’s argument when we determined that Petitioner did not meet that burden.” slip op. at 8
- BurdenDecided for patent owner
“It was Petitioner’s burden to establish the Khatibi, alone or in combination with Shinozaki, Toshio, and Kim, discloses limitation [1d]. We concluded that Petitioner failed to meet that burden for the reasons explained in our Decision. We are not persuaded that we overlooked or misapprehended Khatibi’s disclosures, or Petitioner’s evidence and explanation thereof, in doing so.7” slip op. at 5
§ 103 obviousnesscites KSRPatents in suitUS 10,811,689 - PTAB · Oct 6, 2025 · IPR2025-00611 · APJ Christopher L Ogden · IPR · Institution
The Board instituted IPR of claims 1–10, 12, 13, 19, and 20 on all petition grounds after finding a reasonable likelihood that claim 1 was obvious over Douglas and Mark.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“A claim is unpatentable under § 103 “if the differences between the claimed invention and the prior art are such that the claimed invention as a whole would have been obvious before the effective filing date of the claimed invention to a person having ordinary skill in the art to which the claimed invention pertains.” 35 U.S.C. § 103; see KSR Int’l Co. v. Teleflex Inc., 550 U.S. 398, 406 (2007). When a ground in a petition is based on a combination of references, we consider “whether there was an apparent reason to combine the known elements in the fashion claimed by the patent at issue.” KSR, 550 U.S. at 418 (citing In re Kahn, 441 F.3d 977, 988 (Fed. Cir. 2006)).” slip op. at 8
- Skill levelSkill level petitioner adoptedDecided for petitioner
“The parties agree that experience could substitute for a degree, and vice versa. Pet. 3 (citing Ex. 1003 ¶¶ 19–21); Prelim. Resp. 9. The parties’ proposed levels of ordinary skill are substantially similar. Although we discern no difference in the outcome of this decision from choosing one over the other, we adopt Petitioner’s proposal for this decision. Only Petitioner’s proposed level is supported by testimonial evidence on the preliminary record, and it appears to be consistent with the problems addressed in the ’774 patent. See Ex. 1001, 1:16–52. Therefore, we adopt Petitioner’s proposal for this decision.” slip op. at 7
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“CLAIM CONSTRUCTION B. In an IPR, we construe a patent claim “using the same claim construction standard that would be used to construe the claim in a civil action under 35 U.S.C. 282(b).” 37 C.F.R. § 42.100(b). This generally includes “construing the claim in accordance with the ordinary and customary meaning of such claim as understood by one of ordinary skill in the art and the prosecution history pertaining to the patent.” Id. The ordinary and customary meaning of a claim term “is its meaning to the ordinary artisan after reading the entire patent,” and “as of the effective filing date of the patent application.” Phillips, 415 F.3d at 1313, 1321. Neither Petitioner nor Patent Owner argues that we need to construe any claim terms explicitly. See Pet. 2–3; Prelim. Resp. 9. However, the parties’ positions depend on interpreting the claim language in a particular way, and we discuss the relevant claim language below in the context of the parties’ arguments regarding the prior art. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 7
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundInstituted
“At this stage, we find Petitioner’s arguments persuasive and disagree with Patent Owner. Patent Owner appears to equate a “fabrication profile” with a toolpath description, but nothing in the plain language of claim 1 supports that narrow interpretation. The ’774 patent describes a “fabrication profile” broadly and states that the profile can simply “include the dictionary [of configuration information],” or be “used to determine which machineready representation is available or suitable for a target printer.” Ex. 1001, 23:49–52. The preliminary evidence suggests that Douglas’s “operational parameters” would count as a “fabrication profile” because it is “the basis for generation of a machine-ready representation of the three-dimensional model that is executable on the target printer.” Id. at 23:37–39; see infra Section III.C.8. We also disagree that Petitioner’s argument is impermissible hindsight, because it is based on the disclosures in Douglas and Mark, and Petitioner has articulated a sufficiently persuasive reason to combine those references without referring to the ’774 patent itself. See In re McLaughlin, 443 F.2d 1392, 1395 (CCPA 1971) (an obvious rationale is not improper hindsight if it “takes into account only knowledge which was within the level of ordinary skill at the time the claimed invention was made and does not include knowledge gleaned only from applicant’s disclosure”). Finally, Petitioner appears to rely on Mark for providing a particular example of a fabrication profile, not to replace Douglas’s overall system in which the 3D printer can receive “operational parameters” rather than just G-code. See Pet. 8–10, 17–23; see also Ex. 1005 ¶ 41 (the print queue, which stores tool instructions, may be maintained locally on printers 204 or on print servers 208); see In re Mouttet, 686 F.3d 1322, 1332 (Fed. Cir. 2012) (“[A] determination of obviousness based on teachings from multiple references does not require an actual, physical substitution of elements.” (citing In re Etter, 756 F.2d 852, 859 (Fed. Cir. 1985) (en banc))).” slip op. at 19
Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,886,774
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.