- Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00917 · APJ Debra L Dennett · IPR · Final written decision
Claims 1–17 are unpatentable under § 103 over Chang and Jin, alone or with Seo or Watanabe; the Jin and Feldmann grounds were not shown.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’009 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’009 patent and the prior art.” slip op. at 10
- Expert testimonyPatent owner expert creditedDecided for patent owner
“We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard.” slip op. at 19
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightMotivation not foundNot shown unpatentableNot shown unpatentable
“On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 17
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentableUnpatentable
“Patent Owner focuses on Chang’s description in paragraph 76 of a single configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” Resp. 42 (citing Ex. 1013 ¶ 76). In so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Id. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Chang ¶ 62; Tr. 15:20–17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 73, 217 (citing Ex. 1023 § 1). Chang also discloses that the emitter area may be formed by thermal diffusion, ion implantation or the like. Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding a tunneling layer and a base surface field area from periphery region and isolation region. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” slip op. at 32
Patent outcomesUS 10,230,009 unpatentable§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,230,009 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00006 · APJ Debra L Dennett · IPR · Final written decision
Claims 1–17 are unpatentable under § 103, principally over Chang and Jin; the Board rejected the Jin and Feldmann combinations for lack of a reason to combine.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’009 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’009 patent and the prior art.” slip op. at 10
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 26. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 116 with Pet. 26). Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” See Magnum, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard.” slip op. at 19
- Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable
“configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” Resp. 42 (citing Ex. 1013 ¶ 76). In so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Id. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Chang ¶ 62; Tr. 15:20–17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 73, 217 (citing Ex. 1023 § 1). Chang also discloses that the emitter area may be formed by thermal diffusion, ion implantation or the like. Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding a tunneling layer and a base surface field area from periphery region and isolation region. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” slip op. at 32
Patent outcomesUS 10,230,009 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,230,009 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00918 · APJ Avelyn M Ross · IPR · Final written decision
Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board rejected the Jin and Feldmann based grounds for lack of a reason to combine without hindsight.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16
- Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable
“Patent Owner focuses on Chang’s description in paragraph 76 of a single configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” PO Resp. 42–43 (citing Ex. 1013 ¶ 76). But, in so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Ex. 1013 ¶ 62; Tr. 15:20– 17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 70–81, 91–96, 200 (citing Ex. 1026 § 1 and stating that “[b]oth Chang and Jin likewise teach backside isolation regions”). Chang also discloses that the emitter area may be formed by “thermal diffusion, ion implantation or the like.” Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Pet. Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding the second tunneling layer and a base surface field area from periphery region and isolation portion. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art “reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” Ex. 1003 ¶ 201.” slip op. at 33
Patent outcomesUS 9,722,104 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,722,104 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00186 · APJ Avelyn M Ross · IPR · Final written decision
Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board found the combination disclosed the claimed isolation portion and supported the challenged claims.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached
“C. Claim Construction We construe claim terms according to the standard set forth in Phillips v. AWH Corp., 415 F.3d 1303, 1312–17 (Fed. Cir. 2005) (en banc); 37 C.F.R. § 42.100(b). Under Phillips, we give claim terms “their ordinary and customary meaning.” Phillips, 415 F.3d at 1312. “[T]he ordinary and customary meaning of a claim term is the meaning that the term would have to a person of ordinary skill in the art in question at the time of the invention.” Id. at 1313. “Importantly, the person of ordinary skill in the art is deemed to read the claim term not only in the context of the particular claim in which the disputed term appears, but in the context of the entire patent, including the specification.” Id. Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10
- Expert testimonyPetitioner expert discountedPatent owner expert creditedMixed
“edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001” slip op. at 18
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16
Patent outcomesUS 9,722,104 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,722,104 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00007 · APJ Avelyn M Ross · IPR · Final written decision
Claims 1–11 are unpatentable under §103 over Chang and Jin because the combination teaches the claimed isolation portion and the claimed tapering.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedOther
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightTeaching away not foundNot shown unpatentable
“On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16
- Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner
“However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide.” slip op. at 18
Patent outcomesUS 9,722,104 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,722,104 - Western Digital Technologies, Inc. v. Godo Kaisha IP Bridge 1Some claims unpatentablePTAB · Mar 27, 2026 · IPR2024-01447 · APJ Sheila F Mcshane · IPR · Final written decision
Claims 1–2 are unpatentable as obvious over each Bowen-based combination; claims 3–4 were not shown unpatentable, and the Nagahama-based grounds failed for all claims.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In determining the level of ordinary skill in the art, various factors may be considered, including the “type of problems encountered in the art; prior art solutions to those problems; rapidity with which innovations are 5 Nagahama, EP 1391942 A1, published February 25, 2004 (Ex. 1027, “Nagahama”). made; sophistication of the technology; and educational level of active workers in the field.” In re GPAC Inc., 57 F.3d 1573, 1579 (Fed. Cir. 1995) (citation omitted). The level of ordinary skill in the art is also reflected by the prior art of record. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001). Consistent with the Institution Decision (Dec. 7), we adopt the assessment offered by Petitioner as it is consistent with the ’134 patent and the asserted prior art. Patent Owner does not dispute that Dr. Bokor is qualified as a person of ordinary skill in the art in accordance with the assessment adopted. See Tr. 90:9–15. Patent Owner, however, questions Dr. Bokor’s knowledge on the formation of crystalline materials and seeks to exclude his related testimony. See PO Resp. 1–2, 27; PO Mot. Excl. 12–15. We address this issue infra Section V.” slip op. at 7
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner “submits the claim terms should be given their plain and ordinary meaning and no claim construction is necessary to find the claims unpatentable.” Pet. 24. Patent Owner does not raise any claim construction issues in its Response. See generally PO Resp. We determine that we need not expressly construe any claim terms to resolve the parties’ disputes. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 9
- Strike new argumentNew argument consideredDenied
“A reply may only respond to arguments raised” in the patent owner response. 37 C.F.R § 42.23(b). The Consolidated Trial Practice Guide states that responding “does not mean proceed[ing] in a new direction with a new approach,” and “[w]hile replies . . . can help crystalize issues for decision, a reply . . . that raises a new issue or belatedly presents evidence may not be considered,” that is, “Petitioner may not submit new evidence or argument in reply that it could have presented earlier, e.g. to make out a prima facie case of unpatentability.” Consolidated Trial Practice Guide § II.I (last updated Dec. 12, 2025) (“CTPG”), available at https://www.uspto.gov/patents/ptab/trial-practice-guide. We are not persuaded by Patent Owner’s assertions that Petitioner’s reply arguments on Parkin should not be considered. As discussed supra Section II.D.3.i above, the Petition includes the assertion that if Parkin’s CoFeB electrodes were used to modify Bowen, the MgO polycrystalline or single-crystal layer would still have the same 001 orientation. Pet. 33–34 (citing Ex. 1024 ¶ 129; Ex. 1062, 9:58–10:2, 18:49–51; Ex. 1005, 4:30–32). Petitioner’s support in the Petition references disclosures relating to Parkin’s Figure 3A (Ex. 1062, 18:49–51), which discloses a MgO(100) tunnel barrier, and the Petition also notes that the structure of Figure 3A may be inverted. Pet. 40 (citing Ex. 1062, 17:7–10). Patent Owner’s arguments, in large part, are related to Petitioner’s arguments in the Reply relating to Parkin’s Figure 11. Parkin’s Figure 11 is an embodiment where the structure of the devices of Figure 3A is inverted. See Ex. 1062, 22:29–33. We do not find that Petitioner’s arguments that are at issue in the Reply represent a new direction in its approach—the Petition is clearly based on the assertion that if Parkin’s CoFeB electrodes are used in Bowen, the device would have a MgO(001) tunnel barrier layer. Further, the Petition refers to Parkin’s disclosure that the device in Figure 3A may be inverted, which would be encompassed by the Figure 11 embodiment. Moreover, in the Institution Decision, we invited additional briefing on whether Parkin’s storage magnetic electrode was an amorphous ferromagnetic electrode, which relates to Parkin’s Figure 11 (Dec. 28–29). We are also not persuaded by Patent Owner’s argument that the Petition’s assertions do not correspond to what Petitioner argues in the Reply because they were referred to in the section pertaining to limitation 1[e]. The Petition includes a cross-reference in the limitation 1[d] discussion on the tunnel barrier layer limitation: “if Sunai’s or Parkin’s CoFeB electrodes are used as described in Claims 1[e] and 2 in this Ground, one of skill would understand that the MgO . . . would still have the same (001) orientation.” Pet. 33. Further, Petitioner’s arguments in its Reply properly respond to arguments made on contested issues. Patent Owner’s contentions on the merits in its Response are largely based upon the assertion that the modified MTJ of Bowen would not have a MgO(001) layer as claimed. See PO Resp. 4–10, 18–48. Petitioner’s reply arguments on Parkin relate to whether there would be a MgO(001) layer in its structure, so we find that Petitioner’s arguments on Parkin in its Reply (Pet. Reply 2–5) and the related evidence are appropriately responsive. slip op. at 17
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner
“We find that there is sufficient evidence in support of Petitioner’s assertion of the rationale to replace Bowen’s electrodes with CoFeB and anneal them. As discussed supra Section II.D.ii.2, Parkin’s Figure 11 depicts and describes a storage electrode that may be composed of amorphous CoFeB, with the formation of a MgO(001) barrier layer atop it. See Ex. 1062, 22:29–66. Patent Owner argues that Parkin’s benefits are because its CoFeB electrode is amorphous (PO Resp. 51–52), but this is not accurate. In Parkin, the CoFeB amorphous electrode crystallized at the interface layer between the barrier and the electrode. Id. at 19:6–19. Parkin discloses that higher TMRs were attributable to the crystallization of CoFeB. Id. at 18:63–19:22. Parkin also discloses that its completed CoFeB- MgOH(001)-CoFeB device was annealed with resulting high TMRs. Id. at 17:60–18:16. These disclosures provide support that one of skill in the art would have been motivated to replace Bowen’s electrodes with CoFeB and anneal to crystallize them because of the known improvements of TMR. Additionally, Parkin’s disclosures support that the results of the combination would have been predictable. That is, Parkin actually discloses an amorphous CoFeB electrode, formation of a MgO(001) tunnel barrier on the amorphous electrode, and annealing the assembly, with a resulting high TMR. Accordingly, Petitioner has provided reasoning with rationale underpinning for the motivation to combine. See KSR, 550 U.S. at 415 (“[t]he combination of familiar elements according to known methods is likely to be obvious when it does no more than yield predictable results”).” slip op. at 31
Patent outcomesUS 8,405,134 mixedClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 8,405,134 - Samsung Electronics Co., Ltd. / Samsung Electronics America, Inc. v. Power2b, Inc.All claims unpatentablePTAB · Mar 13, 2026 · IPR2021-01266 · APJ John D Hamann · IPR · Remand
On remand, the Board held claims 29, 36–38, 44–46, 48, 49, and 56–58 unpatentable as obvious over Reime, with additional grounds also supporting the challenged claims.
RulingsRemand decision- ExcludeMotion to exclude, deniedDenied
“In addition, Patent Owner filed a Motion to Exclude certain of Petitioner’s evidence (Paper 32) and Petitioner filed an Opposition (Paper 33). We denied this motion. See Final Dec. 58–61.” slip op. at 3
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for petitioner
“transmission paths. See Pet. Reply 14–15; PO Sur-reply 15. And we agree with both parties that the light that is transmitted directly through the plate to the sensor element does not have intervening reflections—such is consistent with the plain and ordinary meaning of “directly to.” See PO Resp. 31–32; Pet. Reply 14–15; PO Sur-reply 15. Nothing in claim 48’s language, however, requires that all of the reflected light be transmitted directly to the sensor element, which Patent Owner argues. Ex. 1001, 70:32–35; PO Resp. 31–32; PO Sur-reply 14–16. Rather, we agree with Petitioner that the claim language “merely requires that some light reflected by the object goes ‘directly to’ at least one sensor element once it is transmitted through the viewing plane defining plate.” Pet. Reply 14. We also agree that “none of these dependent claims purport to be exclusive of one another.” Id. at 15. Rather, claims 46–48 simply require some light be transmitted (or propagated) for their particular transmission path, without reciting all light. See Ex. 1001, 70:24–35.” slip op. at 13
- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableNot shown unpatentableMixed
“We find Petitioner’s arguments based on Reime alone insufficient. Thus, we find that Petitioner does not show by a preponderance of the evidence that claim 49 is rendered obvious by Reime alone.” slip op. at 52
- Obviousness (§103) › KSR rationalesUnpatentableUnpatentable
“And in view of the above, we find persuasive Dr. Bederson’s testimony that “[c]hoosing a multi-element detector or a single-element detector would have been a simple design choice using commercially available detectors.” Ex. 1002 ¶ 117. Accordingly, we find that one of ordinary skill in the art would have found it obvious for Reime’s receivers to be implemented using discrete single-element detectors. See KSR, 550 U.S. at 417 (“When there is a design need or market pressure to solve a problem and there are a finite number of identified, predictable solutions, a person of ordinary skill has good reason to pursue the known options within his or her technical grasp. If this leads to the anticipated success, it is likely the product not of innovation but of ordinary skill and common sense.”). We find unavailing Patent Owner’s argument that “Petitioner relies on expert testimony to gap-fill missing elements regarding Reime’s failure to disclose or suggest the different claim arrangements of detector elements in a ‘detector assembly.’” PO Resp. 78 (citing Ex. 1002 ¶¶ 111–119; Ex. 2056 ¶ 171). Rather, in light of Reime’s teachings, coupled with the general knowledge of one of ordinary skill in the art, it would have been obvious to employ discrete single-element detectors for Reime’s receivers. See Koninklijke Philips N.V. v. Google LLC, 948 F.3d 1330, 1338 (Fed. Cir. 2020) (finding obviousness can rely on supported expert testimony to supply an element of a claim). We appropriately consider such evidence of the knowledge that one of ordinary skill in the art would have had as part of our obviousness analysis. See Randall Mfg. v. Rea, 733 F.3d 1355, 1362–63 (Fed. Cir. 2013). Moreover, “AAPA can be important evidence of general background knowledge, and general knowledge can be used to supply a missing claim 1371, 1378–79 (Fed. Cir. 2025). Here, Petitioner relies on the cited AAPA as evidence of one of ordinary skill in the art’s general knowledge at the time of the ’093 patent, and the AAPA is not the basis for this ground. See Pet. 4, 42–43; Pet. Remand 4–5. As Shockwave Med. explains, Federal Circuit “case law has long recognized numerous permissible uses for general background knowledge in an IPR such as, ‘for example, furnishing a motivation to combine, or supplying a missing claim limitation.” 142 F.4th at 1378–79 (quoting Qualcomm Inc. v. Apple Inc., 24 F.4th 1367, 1376 (Fed. Cir. 2022) (citing Randall Mfg., 733 F.3d at 1362; Koninklijke, 948 F.3d at 1337–38)).” slip op. at 31
Patent outcomesUS 9,569,093 unpatentableClaim construction§ 103 obviousnesscites Phillips · GrahamPatents in suitUS 9,569,093 - Samsung Electronics Co., Ltd. / Samsung Electronics America, Inc. v. Power2b, Inc.All claims unpatentablePTAB · Mar 13, 2026 · IPR2021-01239 · APJ John D Hamann · IPR · Remand
On remand, the Board held claims 17, 18, 21, 22, 26, and 30 unpatentable as obvious over Reime, with claims 17, 18, 21, 22, and 30 also obvious over Reime and Hinckley.
RulingsRemand decision- ExcludeMotion to exclude, deniedDenied
“In addition, Patent Owner filed a Motion to Exclude certain of Petitioner’s evidence (Paper 28) and Petitioner filed an Opposition (Paper 34). We denied this motion. See Paper 41, 47–50.” slip op. at 3
- Skill levelSkill level board ownOther
“one having ordinary skill in the art at the time of the invention of the ’850 patent: one who “would have had a bachelor’s degree in electrical engineering, computer engineering, computer science, or a related field, and . . . years of experience in the research, design, development, and/or testing of touch and/or proximity sensors, human-machine interaction and 3 The Leahy-Smith America Invents Act (“AIA”) included revisions to 35 U.S.C. § 103 that became effective on March 16, 2013. Because the ’850 patent issued from an application filed before March 16, 2013, we apply the pre-AIA version of the statutory basis for unpatentability. 4 US 2003/0034439 A1, published Feb. 20, 2003 (Ex. 1010, “Reime”). 5 US 2002/0021278 A1, published Feb. 21, 2002 (Ex. 1011, “Hinckley”). Petitioner lists the combination of Reime and Hinckley as a separate asserted ground for claim 26. We combine these two asserted grounds into one as they rely on the same combination. additional education substituting for experience and vice versa.” Final Dec. 8–9. This definition for one having ordinary skill was not the subject of appeal, and we maintain it for purposes of this Final Written Decision on Remand. Moreover, it is consistent with the ’850 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 8
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner
“PO Resp. 17–29; Pet. Reply 8–15; PO Sur-reply 6–11. We construed this term in the Final Written Decision. Final Dec. 10–24. In particular, we concluded that (i) “detector assembly” means “two or more detector elements that detect electromagnetic radiation,” and (ii) a detector assembly is not required to be physically separate from (i.e., not interspersed with) a pixel array. Id. at 20, 22. The Federal Circuit found the first part of our construction erroneous. Appeal Dec. 7–10. In particular, the Federal Circuit concluded that “[t]he element.” Id. at 8. In addition, to guide the Board’s analysis on remand, the Federal Circuit construed “the terms ‘at an edge’ and ‘at least one edge’ [to] require a detector assembly to be arranged along one or more edges of a viewing plane defining plate.” Id. at 10–11. In other words, the Federal Circuit “clarif[ied] that arranging a detector assembly ‘at,’ ‘along,’ or ‘about’ ‘at least one edge’ or ‘an edge’ does not limit the detector assembly to being arranged entirely on ‘one edge.’” Id. at 12.” slip op. at 9
- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable
“the Federal Circuit already has concluded that claim 15 is obvious in view of Reime. Appeal Dec. 9–10. Claim 17 further recites “wherein the detector assembly comprises: a support substrate, and an arrangement of detector elements.” Ex. 1001, 67:15–18. We agree with Petitioner and find that Reime teaches these further limitations. Pet. 34–35; Pet. Remand 2–4; Pet. Resp. Remand 1–3. First, as we found in the Final Written Decision, Reime’s receivers 30 and 32 are two detector elements that detect electromagnetic radiation (i.e., light), and Reime’s receivers 30 and 32, collectively, comprise a detector assembly. Final Dec. 27–28 (citations omitted). Moreover, Reime’s two receivers 30 and 32 comprise a detector assembly having multiple detector elements (e.g., two receivers) to teach “an arrangement of detector elements.” Ex. 1010 ¶¶ 73, 86, Figs. 9A–9C; Ex. 2060,7 127:17–18; Pet. 32–33; Pet. Reply 20; Pet. Remand 3. In addition, as we found in the Final Written Decision, Reime teaches that each of receivers 30 and 32 are centered on opposite edges of the plate. 7 Deposition Transcript of Dr. Benjamin Bederson (Apr. 7, 2022). Ex. 1010, Fig. 6A, ¶ 82) (affirming that Reime teaches having one light receiver (e.g., 30 or 32) on each side of a four-sided touch pad). In further support, we agree with Petitioner and find that Reime teaches that receivers 30 and 32 “are mounted in the peripheral area surrounding the LCD 92.” Pet. 32–33; Ex. 1010 ¶ 86; see also id. at Figs. 9A–9C (showing that the receivers are positioned at the edge of the LCD screen); infra annotated Fig. 9E (showing receivers 30 and 32 along edges of the LCD). Accordingly, we find Reime’s detector assembly that comprises receivers 30 and 32 is arranged along two edges (one edge for each receiver) of the LCD, which meets the Federal Circuit’s construction for being arranged at at least one edge. See supra Section III (concluding “at least one edge” means “arranged along one or more edges”) (emphasis added).” slip op. at 12
Patent outcomesUS 8,624,850 unpatentableClaim construction§ 103 obviousnesscites Phillips · GrahamPatents in suitUS 8,624,850 - Reolink Innovation Inc. / Shenzhen Reolink Technology Co., Ltd. v. Throughtek Co., Ltd.All claims unpatentablePTAB · Jan 23, 2026 · IPR2024-01192 · APJ Michael J Strauss · IPR · Final written decision
Claims 1–10 and 16 are unpatentable as obvious over the asserted combinations of the Lorex Manual or Lorex Video with the identified references.
RulingsFinal written decision- Novelty / Anticipation (§102) › Priority / effective filing date / continuation supportPriority date awardedDecided for petitioner
“Patent Owner does not dispute any of Petitioner’s contentions as to the effective filing date, stating in agreement with Petitioner’s asserted Effective Filing Date of the Challenged Claims that “[t]he ’916 Patent claims a priority of a provisional application 61/924,240 filed on January 7, 2014.” PO Resp. 8. Given that the parties are in agreement on the January 7, 2014, effective filing date, we similarly use January 7, 2014, as the effective filing date of the challenged claims for purposes of this Decision.” slip op. at 4
- Skill levelSkill level petitioner adoptedDecided for petitioner
“II. ANALYSIS A. Level of Ordinary Skill in the Art Relying on the testimony of Vlad Kardashov, Petitioner proposes that a person of ordinary skill in the art at the time of the invention of the ’916 patent “would have had a bachelor’s degree in electrical engineering and two 7 US 2012/0198040 A1, published August 2, 2012 (Ex. 1011, “Kuo”). 8 The subject ’916 patent claims priority to Kuo as a continuation-in-part of that earlier filed application. Ex. 1001, code (63). 9 Lorex Technology Inc., “How to set up remote access for DVR using - Lorex Stratus Connectivity” (June 18, 2013), available at https://www. youtube.com/watch?v=fMPRi9WFuTM (Ex. 1012, the “Lorex Video”). 10 US 2012/0113265 A1, published May 10, 2012 (Ex. 1013, “Galvin”). years of work experience with network and communication technologies.” Pet. 8 (citing Ex. 1003 ¶¶ 12–14). Patent Owner does not contest Petitioner’s proposal or provide a proposal of its own. On the complete record, we adopt Petitioner’s description of the level of ordinary skill in the art, as it is consistent with the technology described in the ’916 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner asserts that “no claim elements need a formal construction for purposes of resolving controversies in this proceeding.” Pet. 9 (citing Ex. 1003 ¶¶ 43–44; Wellman, Inc. v. Eastman Chem. Co., 642 F.3d 1355, 1361 (Fed. Cir. 2011), Google Inc. v. Intellectual Ventures II LLC, 701 Fed. Appx. 946, 956 (Fed. Cir. 2017)). Petitioner states “[a]ll claim terms should be construed according to the Phillips standard.” Id. (citing Phillips, 415 F.3d at 1303; 37 C.F.R. § 42.100). Patent Owner presents no proposed claim constructions. We determine that we need not expressly construe any claim terms to resolve the parties’ disputes on the current record. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 9
- Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityReference is prior artPriority date awardedDecided for petitioner
“that Patent Owner fails to demonstrate that the Lorex Manual was based on a disclosure made by the inventor or joint inventor or by another who obtained the subject matter disclosed directly or indirectly from the inventor or a joint inventor. The Lorex Manual is relied on under Ground 1A, exclusively or in the alternative to or in combination with Kim, for all claim elements. Pet. 9– 31. Patent Owner fails to demonstrate that this subject matter was disclosed to Lorex by ThroughTek, much less by one of the inventors of the ’916 Patent.” slip op. at 22
Patent outcomesUS 9,774,916 unpatentableClaim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,774,916 - PTAB · Jan 14, 2026 · IPR2025-00632 · APJ Mitchell G Weatherly · IPR · Remand
On remand, the Board reinstituted review of all challenged claims on all grounds after finding Petitioner sufficiently explained its differing claim-construction positions.
RulingsRemand decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“Id. The Director neither addressed the merits of Petitioner’s challenges nor found that our prior consideration of those merits was faulty. Accordingly, we understand that we need not reconsider our conclusion that Petitioner had demonstrated a reasonable likelihood of proving that claims 1, 2, 7–9, 11, 12, and 20–24 were unpatentable or that the merits of patentability set forth in the Petition warranted institution of inter partes review.” slip op. at 5
- BurdenDecided for petitioner
“The question before us, therefore, is whether the Petitioner’s proffered explanation that it has proposed a different claim interpretation before the Board because the District Court may decline to adopt the narrower claim interpretations it advocates there is sufficient. We find that Petitioner’s explanation is sufficient because it follows the Director’s exemplary logic. Whether a district court has already or might in the future decline to adopt constructions that a petitioner proposes in related district court litigation merely reflects the timing of when a dispute over claim interpretation will be resolved. The Director and Patent Owner both recognize that, to resolve the dispute over claim interpretation that exists here, a decision-maker must determine “a single claim construction that best captures the true meaning of the patent claim.” Remand 4; PO Remand Br. 3. Based on the record presented by the parties to date in this proceeding, no dispute exists that the disputed claim terms mean what Patent Owner says they mean in the Litigation. Accordingly, we find that, at this stage of the proceeding, it is undisputed that Patent Owner’s interpretations of the claim terms represent the “single claim construction that best captures the true meaning of the patent claim.”8 Under that claim interpretation, we” slip op. at 8
NonePatents in suitUS 11,835,421
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.