- Abbott Laboratories v. Miracor Medical SAAll claims unpatentablePTAB · Jun 8, 2026 · IPR2025-00112 · APJ James A Tartal · IPR · Final written decision
Claims 1–3, 10, 11, 14, and 17 are unpatentable as obvious over Schima and Akamatsu; the other asserted grounds were not established.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“may be considered, including the “type of problems encountered in the art; prior art solutions to those problems; rapidity with which innovations are made; sophistication of the technology; and educational level of active workers in the field.” In re GPAC Inc., 57 F.3d 1573, 1579 (Fed. Cir. 1995). Petitioner contends a person of ordinary skill in the art at the time of the invention “would have at least a bachelor’s degree in engineering; knowledge and experience in human circulatory system anatomy and physiology; and at least five years’ experience designing and developing implantable medical devices.” Pet. 6 (citing Ex. 1003 ¶ 18).” slip op. at 10
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner
“sufficient basis for limiting the plain meaning of “magneto coupling.” That the ’357 patent describes embodiments using bar magnets does not serve to require the use of permanent magnets for the recited “magneto coupling.” See Sisvel Int’l S.A. v. Sierra Wireless, Inc., 81 F.4th 1231, 1236 (Fed. Cir. 2023) (quoting Phillips, 415 F.3d at 1323 (“[A]lthough the specification often describes very specific embodiments of the invention, we have repeatedly warned against confining the claims to those embodiments.”)). Moreover, the claim language here is not so limited. 11 Patent Owner notes that Petitioner’s grounds of unpatentability based on Wampler and Bourque depend on the disclosure only of electromagnetic drives in each reference, implying that “Petitioner does not believe its own proposed narrower construction.” PO Resp. 6; see also Pet. 8 (Petitioner alleging that in the Parallel Proceeding Patent Owner “conflates ‘magneto coupling’ . . . with a stator drive using a stationary electromagnet, instead of a rotating magnet, to rotate the rotor magnet,” and asserting that as the basis for Petitioner’s reliance on Wampler and Bourque as teaching a “magneto coupling” in this proceeding (citing Ex. 1019, 9–11; Ex. 1003 ¶¶ 84–87)). distinguished “magneto coupling” drives from drives using stators. Pet. 7–8 (citing Ex. 1011, 1 (explaining that the rotating field is generated by rotating magnets in a magnetic coupling pump and by electric stator windings in a stator pump)). Petitioner does not explain how this cited reference evidences that one of ordinary skill in the art would have understood “magneto coupling” requires rotating permanent magnets. At most, this reference teaches an example device that provides “magneto coupling.” See Ex. 1011, 1. In sum, we agree with Patent Owner that “magneto coupling,” consistent with our Institution Decision, encompasses generating a rotating field either by rotating magnets or by an electromagnet / stator. See Inst. Dec. 22” slip op. at 22
- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable
“ignores the readily apparent fact that the lower arrow is placed in a location that misrepresents the minimum distance between the magnetically driven rotor and the second magnetic device to suggest that Wampler teaches “the second magnetic device positioned axially closer to the first magnetic device than to the magnetically driven rotor,” as required by claim 1. Petitioner purports to justify this misrepresentation by asserting that “the vast majority of the impeller 74 is spaced significantly farther apart from the stators 90 and 94 than the magnetic pieces 88 are positioned from the stators 90 and 94.” Id. at 33–34. Claim 1 does not recite any feature based on the “vast majority” of a component and it is readily apparent from Petitioner’s own annotated version of Figure 11a that the distance from both the “motor magnets [88]” and “impeller 74” to the “circular electromagnetic stator[s] [90 and 94]” is the same. We agree with Patent Owner that Petitioner has provided a “misleading Figure with two red arrows denoting measurement distances to illustrate its incorrect view that the second magnetic device is farther from the magnetically driven rotor than from the first magnetic device.” PO Resp. 13–15 (providing an annotated version of Wampler’s Figure 11a with an orange arrow showing that in Wampler the distances from the second magnetic device to both the rotor and the first magnetic device are the same). Accordingly, Petitioner fails to show that Wampler teaches “the second magnetic device positioned axially closer to the first magnetic device than to the magnetically driven rotor.”” slip op. at 29
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable
“To orient the pump in the least obtrusive position (i.e., in the human configuration, as in Figure 3), it was decided that the rotational axis of the pump’s rotor should be perpendicular to the body’s long axis. That resulted in a sharp bend in the flow before it enters the impeller. To minimize the losses in this transition, the flow is slightly accelerated through this elbow. that this type of elbow [i.e., the elbow used with Bourque’s centrifugal pump] was unnecessary,” applying Wampler to Bourque would have improved “blood flow.” Pet. 73 (citing Ex. 1003 ¶¶ 418–419; Ex. 1007, 402; Ex. 1008 ¶¶ 75–76). As explained above, Wampler does not teach that “this type of elbow” was unnecessary. Bourque uses a centrifugal pump with an additional elbow specifically so that the centrifugal pump may be oriented “in the least obtrusive position.” Ex. 1007, 402. Moreover, there is no persuasive evidence to support Petitioner’s assertion that eliminating the elbow from Bourque would improve “blood flow.” Mr. Crosby’s declaration provides no additional explanation or support to show how “blood flow” would have been improved. See Ex. 1003 ¶ 419. Nor does Mr. Crosby address the fact that Bourque expressly states that “flow is slightly accelerated” through the elbow to “minimize losses in this transition.” Ex. 1007, 402. Eliminating the elbow from Bourque, as Petitioner and Mr. Crosby propose, would mean the pump could no longer be placed in “the least obtrusive position” according to Bourque and there is no persuasive evidence that such a modification would improve blood flow.” slip op. at 45
Patent outcomesUS 11,351,357 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,351,357 - Abbott Laboratories v. Miracor Medical SAAll claims unpatentablePTAB · Jun 4, 2026 · IPR2025-00113 · APJ James A Tartal · IPR · Final written decision
Claims 1–5, 10, 11, 14, 16, and 17 are unpatentable under §103 over Schima and Akamatsu.
RulingsFinal written decision- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable
“reasons discussed above. See supra Section III.D.3. Accordingly, because Petitioner’s contentions are premised on an unsupported claim construction that we reject, Petitioner fails to show how Wampler teaches or suggests “a magnetically driven rotor . . . axially adjacent to a first magnet device,” as required by claim 1, as well as by claims 2–5, 10, 11, 14, 16, and 17, which depend from claim 1. In its Reply, Petitioner suggests that “[u]nder [Patent Owner’s] construction from the [Patent Owner Response], Wampler also teaches or suggests this limitation,” because Patent Owner “concedes that ‘axially adjacent’ components ‘have positioning that is next to one another, perhaps touching or sharing a common side, when measured along the axis.’” Pet. Reply 11 (citing PO Resp. 17). Petitioner mischaracterizes Patent Owner’s arguments and ignores Patent Owner’s showing that “axially adjacent” components are “distinct from components that are aligned with one another such that they overlap or occupy the same portion of an axis” slip op. at 32
- Obviousness (§103) › Analogous artAnalogous artDecided for petitioner
“endeavor of the ’415 patent (i.e., “[a] method and device to assist the performance of a heart with at least one pump that is formed as a rotary pump and driven via magneto coupling”). See Ex. 1001, code (57); Ex. 1005 code (57); Ex. 1006, 1. Accordingly, we determine that Petitioner has sufficiently shown that Schima and Akamatsu are analogous art to the ’415 patent.” slip op. at 71
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner
“endeavor of the ’415 patent (i.e., “[a] method and device to assist the performance of a heart with at least one pump that is formed as a rotary pump and driven via magneto coupling”). See Ex. 1001, code (57); Ex. 1005 code (57); Ex. 1006, 1. Accordingly, we determine that Petitioner has sufficiently shown that Schima and Akamatsu are analogous art to the ’415 patent.” slip op. at 71
- ExcludeMotion to exclude, deniedDenied
“not identified a persuasive basis under any of the Federal Rules of Evidence for the exclusion of evidence in this proceeding and deny the Motion.” slip op. at 78
Patent outcomesUS 11,376,415 unpatentable§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,376,415 - Dr. Falk Pharma GmbH v. Ellodi Pharmaceuticals, L.P.Adverse judgmentPTAB · Jun 3, 2026 · PGR2025-00086 · APJ Tawen Chang · PGR · Adverse judgment
The Board granted Patent Owner’s request for adverse judgment and terminated the PGR as to claims 1–34 after Patent Owner disclaimed all challenged claims.
RulingsAdverse judgment- Adverse judgmentAdverse judgmentGranted
“A party may request judgment against itself at any time during a proceeding,” including by “[d]isclaimer of the involved application or patent” or “[c]ancellation or disclaimer of a claim such that the party has no remaining claim in the trial.” 37 C.F.R. §§ 42.73(b)(1)–(b)(2). Accordingly, we grant Patent Owner’s Request for Adverse Judgment and terminate the proceeding. slip op. at 2
NonePatents in suitUS 12,290,598 - Shenzhen Tuozhu Technology Co. Ltd. v. Stratasys, Inc.All claims unpatentablePTAB · Jun 3, 2026 · IPR2025-00257 · APJ Lilan Ren · IPR · Final written decision
Claims 1–15 are unpatentable because Petitioner proved by a preponderance of the evidence that the asserted § 103 grounds render them unpatentable.
RulingsFinal written decision- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable
“proceeding, we determine Petitioner has proven by a preponderance of the evidence that each of claims 1–15 of the ’660 patent is unpatentable.” slip op. at 85
Patent outcomesUS 9,592,660 unpatentable§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,592,660 - Berkshire Hathaway Energy Company / Pacificorp v. Birchtech Corp.Institution deniedPTAB · May 18, 2026 · IPR2025-00278 · APJ David Cotta · IPR · Institution
The Board denied institution of Berkshire Hathaway Energy Company and PacifiCorp’s petition because it had instituted the earlier-filed IPR2025-00274 challenging the same patent.
RulingsInstitution decision- PTAB / AIA Trials › Real party in interest / privityRpi dispute resolved for petitionerDecided for petitioner
“request from Patent Owner for Director Review, finding that Patent Owner introduced “evidence sufficient to put RPI and privity at issue” and remanding with instructions to “allow discovery, narrowly tailored to resolve the RPI and privity issues” including “at least materials sufficient to clarify the evidence the Board found to be ‘ambiguous’ and to avoid the need for the Board to ‘speculate as to the nature of the redacted material.’” Paper 57 (Decision on Request for Director Review). The Director instructed that after allowing such discovery, we “should then determine on the full record whether Petitioners have met their burden of demonstrating that the Petitions are not time-barred under § 315(b), applying the framework set forth in Worlds Inc. v. Bungie, Inc., 903 F.3d 1237, 1242–44 (Fed. Cir. 2018). Concurrently herewith, we issue a decision in IPR2025- 00278 finding that Petitioner has met its burden of demonstrating that its Petition is not time-barred under 35 U.S.C. § 315(b).” slip op. at 2
- Other 314aInstitution denied discretionary otherInstitution denied
“Review Decision instructing that “if the Board determines that Petitioners met their burden to identify all RPIs in the Petitions, then the Board should maintain at most one IPR challenging each of the ’114 patent, the ’517 patent, the ’430 patent, and the ’225 patent.” Paper 79, 3. Together with its Petition in this proceeding and the proceeding in IPR2025-00274, Petitioner filed an Explanation Regarding the Necessity of Multiple Petitions. Paper 2 (“Explanation”); IPR2025-00274, Paper 2. In the Explanation, Petitioner “request[s] that, if the Board uses its discretion to institute the Petitions, the Board consider the merits of IPR2025-00274 . . . before IPR2025-00278.” Explanation, 3. Further to Petitioner’s request, we first considered the merits of IPR2025-00274. For the reasons discussed in our concurrently issued decision in IPR2025-00274, we institute inter partes review on the grounds set forth in the Petition in IPR2025-00274. Further to the Director’s instruction that we “maintain at most one IPR challenging . . . the ’114 patent,” and the Petitioner’s request that we consider the merits of IPR2025-00274 before IPR2025-00278, we deny institution of the Petition in this proceeding.” slip op. at 3
Discretionary denialPatents in suitUS 10,343,114 - Berkshire Hathaway Energy Company / Pacificorp v. Birchtech Corp.Institution deniedPTAB · May 18, 2026 · IPR2025-00281 · APJ David Cotta · IPR · Institution
The Board denied institution because it had instituted IPR2025-00280 challenging the same patent, consistent with the Director’s instruction to maintain at most one IPR.
RulingsInstitution decision- Other 314aInstitution denied discretionary otherInstitution denied
“Review Decision instructing that “if the Board determines that Petitioners met their burden to identify all RPIs in the Petitions, then the Board should maintain at most one IPR challenging each of the ’114 patent, the ’517 patent, the ’430 patent, and the ’225 patent.” Paper 79, 3. Together with its Petition in this proceeding and the proceeding in IPR2025-00280, Petitioner filed an Explanation Regarding the Necessity of Multiple Petitions. Paper 2 (“Explanation”); IPR2025-00281, Paper 2. In the Explanation, Petitioner “request[s] that, if the Board uses its discretion to institute the Petitions, the Board consider the merits of IPR2025-00280 . . . before IPR2025-00281.” Explanation, 3. Further to Petitioner’s request, we first considered the merits of IPR2025-00280. For the reasons discussed in our concurrently issued decision in IPR2025-00280, we institute inter partes review on the grounds set forth in the Petition in IPR2025-00280. Further to the Director’s instruction that we “maintain at most one IPR challenging . . . the ’517 patent,” and the Petitioner’s request that we consider the merits of IPR2025-00280 before IPR2025-00281, we deny institution of the Petition in this proceeding.” slip op. at 3
Discretionary denialPatents in suitUS 10,596,517 - Western Digital Technologies, Inc. v. Godo Kaisha IP Bridge 1Some claims unpatentablePTAB · Apr 29, 2026 · IPR2024-01493 · APJ John D Hamann · IPR · Final written decision
Claims 1, 3, 5, 7–11, 14, and 15 are unpatentable as obvious; claims 2, 4, 6, 12, and 13 were not shown unpatentable because the references did not establish entirely crystallized CoFeB layers.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In our Decision on Institution, we adopted the definition Petitioner proposes for one having ordinary skill in the art at the time of the invention of the ’167 patent. Dec. on Inst. 6. Namely, we found that one of ordinary skill in the art would have had “a Ph.D. in electrical engineering, physics, materials science, or a related field, and at least one year of experience in the research, design, and/or development of magnetic/spintronic devices, or the equivalent,” or “a Master’s degree in electrical engineering, physics, materials science, or a related field, and four years of experience in the research, design, and/or development of magnetic/spintronic devices, or the equivalent.” Id. (citing Pet. 20 (citing Ex. 1024 ¶ 25)). We also found that “[l]ess work experience may be compensated by a higher level of relevant education, and vice versa.” Id. Patent Owner does not address Petitioner’s definition, nor provide its own. See generally PO Resp. Because Petitioner’s definition of the level of skill in the art is consistent with the ’167 patent and the asserted prior art, we maintain it for purposes of this Final Written Decision. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001); In re GPAC, 57 F.3d at 1579; In re Oelrich, 579 F.2d 86, 91 (CCPA 1978).” slip op. at 7
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for petitioner
“Here, neither party sets forth any term for claim construction. Pet. 17; see generally PO Resp. Thus, for purposes of this Decision, we afford the claim terms their plain and ordinary meaning. See, e.g., Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’”)).” slip op. at 8
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner
“In addition, we agree with Petitioner and find that one of ordinary skill in the art “would have been motivated to replace either or both of Bowen’s electrodes with CoFeB to increase TMR and lower Hf [(coupling field)] and Hc [(coercivity)].” Pet. 24, 27; Ex. 1055,30 2270 (“[I]t is natural to replace both the free and pinned layers to CoFeB to further increase the TMR value.”); Ex. 105631 ¶¶ 67–68 (“[B]oth the ferromagnetic layers 5, 7 are made of an FeCoB”32 for “improvement of the TMR ratio.”); Ex. 1024 ¶¶ 129, 132. We credit Dr. Bokor’s cited testimony as it is consistent with the cited evidence. Moreover, as Petitioner explains, “[r]esearchers were . . . interested in optimizing MTJs to improve MRAM performance,” and “[h]igher TMRs long promised improved performance for MRAM.” Pet. 6 30 Dexin Wang et al., 70% TMR at room temperature for SDT sandwich junctions with CoFeB as free and reference layers, 40 IEEE Trans. Magn. 2269–71 (July 2004). 31 US 2004/0136232 A1, published July 15, 2004, to Hosomi. 32 We find persuasive Dr. Bokor’s testimony that “a skilled artisan [would have] understood that CoFeB and FeCoB refer to the same alloy.” Ex. 1024 ¶ 121. 36–44) (emphasis omitted). In addition, we agree with Petitioner that one of ordinary skill in the art “would have found it obvious to use Parkin’s CoFeB layer in place of Bowen’s electrodes to increase TMR” in light of Parkin’s explicit teachings. Pet. 27; Ex. 1024 ¶ 133. In particular, Parkin explicitly teaches that “very high TMR values are unexpectedly found for MTJs with highly textured (100) MgO tunnel barriers but with nominally amorphous storage layers.” Ex. 1062, 18:49–51. Notably, Parkin provides that “[t]he TMR of the device of F[igure] 3A is nearly two times higher than the highest TMR ever reported in prior art devices using conventional alumina tunnel barriers.” Id. at 18:63–65; Pet. 27. And as we discuss above, Parkin teaches that Figure 3A’s MTJ may be inverted, such that the storage layer is formed beneath the tunnel barrier. Ex. 1062, 17:7–10. In addition, we agree that one of ordinary skill in the art would have had a reasonable expectation of success in modifying Bowen in the manner Petitioner proposes, as forming electrodes with CoFeB alloys was known. Pet. 28. As Petitioner argues, “forming electrodes with CoFeB alloys in MTJs was known and had been successfully done,” and thus we are persuaded that “one of skill would have found it to be a straightforward, predictable, and desirable improvement to TMR, Hf, and Hc in Bowen’s” slip op. at 21
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner
“We find unavailing Patent Owner’s arguments that Bowen teaches a “radically different manufacturing process[] from the claimed invention,” and that Bowen “went to heroic lengths to provide a crystalline (001) bottom electrode that provides a template for epitaxially growing a crystalline MgO(001) layer.” PO Resp. 2 (emphasis omitted). Patent Owner describes in detail Bowen’s specific manufacturing process, including the specific structure of the MTJ manufactured, and argues the claimed invention differs. PO Resp. 30–33. These arguments are inapposite. Petitioner cites the specific teachings Petitioner relies on from Bowen, rather than adopting the entirety of Bowen’s process or MTJ. See, e.g., Pet. 21–36 (citing the portions of Bowen—that in combination with Parkin—teach claim 1). Petitioner is not “compelled to adopt every single aspect of [Bowen’s] teaching without the exercise of independent judgment.” Lear Siegler, Inc. v. Aeroquip Corp., 733 F.2d 881, 889 (Fed. Cir. 1984). We also find unavailing Patent Owner’s argument that Bowen and Parkin each teach away from Petitioner’s combination because Parkin used boron to avoid crystalline electrodes whereas Bowen tried to achieve perfect crystalline electrodes. PO Resp. 4. As we discuss above, one of ordinary skill in the art would have been motivated to replace Bowen’s electrodes with CoFeB to increase TMR. And Patent Owner does not identify in either reference a specific teaching that criticizes, discredits, or otherwise 35 M. Jimbo et al., Thermal stability of spin valves using amorphous CoFeB, 165 J. Magnetism & Magnetic Materials 308–11 (1997) (“Jimbo”). combination. In re Fulton, 391 F.3d 1195, 1201 (Fed. Cir. 2004).” slip op. at 23
Patent outcomesUS 10,680,167 mixedClaim construction§ 103 obviousnesscites Phillips · GrahamPatents in suitUS 10,680,167 - Western Digital Technologies, Inc. v. Godo Kaisha IP Bridge 1No claims unpatentablePTAB · Apr 28, 2026 · IPR2024-01494 · APJ Justin T Arbes · IPR · Final written decision
The Board found claims 5, 6, and 9–20 not shown unpatentable over either Bowen and Soukup or Nagahama and Soukup under § 103.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner argues that at the time of the ’909 patent (2004), a person of ordinary skill in the art would have had “a Ph.D. in electrical engineering, physics, materials science, or a related field, and at least one year of experience in the research, design, and/or development of magnetic/spintronic devices, or the equivalent,” or “a Master’s degree in electrical engineering, physics, materials science, or a related field, and four years of experience in the research, design, and/or development of magnetic/spintronic devices, or the equivalent,” where “[l]ess work experience may be compensated by a higher level of relevant education, and vice versa.” Pet. 18–19. In the Decision on Institution, we agreed with and applied Petitioner’s proposed definition. Dec. on Inst. 9. Patent Owner does not propose a different level of ordinary skill in the art in its Response. Both experts utilized Petitioner’s proposed definition. See Ex. 1024 ¶ 25; Ex. 2053 ¶¶ 29–30. Based on the full record developed during trial, including our review of the ’909 patent and the types of problems and solutions described in the ’909 patent and cited prior art, we maintain the previously adopted definition of the level of ordinary skill in the art and apply it for purposes of this Decision.” slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“B. Claim Interpretation We interpret the claims of the challenged patent using the same claim construction standard that would be used to construe the [claims] in a civil action under 35 U.S.C. 282(b), including construing the [claims] in accordance with the ordinary and customary meaning of such [claims] as understood by one of ordinary skill in the art and the prosecution history pertaining to the patent. 37 C.F.R. § 42.100(b). Petitioner argues that “the claim terms should be given their plain and ordinary meaning and no claim construction is necessary.” Pet. 15. We did not interpret any terms in the Decision on Institution. Dec. on Inst. 9–10. Patent Owner does not propose interpretations of any claim terms in its Response. We conclude, based on the full trial record, that no term requires express interpretation to determine whether Petitioner has met its burden to prove unpatentability of the challenged claims. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“Because we need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy,’ we need not construe [a particular claim limitation] where the construction is not ‘material to the . . . dispute.’” (emphasis added) (citation omitted)).” slip op. at 8
- Strike new argumentNew argument disregardedGranted in part
“Pursuant to 37 C.F.R. § 42.23(b), “[a] reply may only respond to arguments raised in the corresponding . . . patent owner response.” “‘Respond,’ in the context of 37 C.F.R. § 42.23(b), does not mean proceed in a new direction with a new approach as compared to the positions taken in a prior filing.” Patent Trial and Appeal Board Trial Practice Guide § II.I, available at https://www.uspto.gov/patents/ptab/trial-practice-guide (last updated Dec. 12, 2025). “While replies . . . can help crystalize issues for decision, a reply . . . that raises a new issue or belatedly presents evidence may not be considered.” Id. An indication that a new issue is improperly raised in a reply is where a petitioner submits “new evidence necessary to make out a prima facie case” of unpatentability, such as a “newly raised rationale to combine the prior art references that was not expressed in the petition.” Id. That is the case here. Petitioner’s rationale in the Petition for why a person of ordinary skill in the art would have been motivated to lower Bowen’s 0.9 eV barrier height to 0.33 eV based on Soukup was that such an artisan would have expected lowering the barrier height to increase TMR. See Pet. 34–36. Faced with Dr. Bokor’s testimony on cross-examination, Petitioner presents a new theory in its Reply that a person of ordinary skill in the art would not have known what impact lowering the barrier height would have (increase TMR, decrease it, or have no impact at all), but would have expected it to change in some “uncertain” way, which is a “legally sufficient motivation” in Petitioner’s view. See Reply 6–10, 13–16, 23–25. In other words, “[r]ather than explaining how its original” position that lowering barrier height would increase TMR “was correct,” Petitioner articulated “an entirely new theory . . . absent from the [P]etition” after Patent Owner cross-examined Dr. Bokor and “pointed out the flaws of [Petitioner’s] position” in its Response. See Wasica Finance GmbH v. Continental Auto. Sys., Inc., 853 F.3d 1272, 1286 (Fed. Cir. 2017). “Shifting arguments in this fashion is foreclosed by statute, [Federal Circuit] precedent, and Board guidelines.” Id.” slip op. at 20
- Expert testimonyPetitioner expert discountedPatent owner expert creditedDecided for patent owner
“Ultimately, the cross-examination testimony above is inconsistent with Dr. Bokor’s opinions in his declaration that, for example, “[i]t was understood to one of skill that lowering the barrier height to increase tunneling would have increased the TMR,” and “[o]ne of skill would have been motivated to adjust oxygen vacancy defects to improve TMR by lowering the barrier height.” See Ex. 1024 ¶¶ 176, 277 (emphasis added); see also id. ¶ 172 (“[O]ne of skill in the art would have been motivated to use [Soukup’s 0.33 eV] or similar height in an MgO MTJ to improve tunneling and hence TMR in Bowen.”). Accordingly, we do not find Dr. Bokor’s declaration testimony regarding a motivation to lower Bowen’s barrier height credible. It is Petitioner’s burden to provide a reasoned, evidence-supported explanation for why a person of ordinary skill in the art would have been motivated to lower Bowen’s 0.9 eV barrier height to 0.33 eV as disclosed in Soukup. See NuVasive, 842 F.3d at 1383; Magnum Oil, 829 F.3d at 1380; TriVascular, 812 F.3d at 1066. Petitioner’s reasoning in the Petition that lowering the barrier height (by introducing oxygen defects) would increase TMR is unsupported by evidence.” slip op. at 31
Patent outcomesUS 11,968,909 not shown unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 11,968,909 - Luxottica Of America Inc. v. E-Vision Smart Optics, Inc.Adverse judgmentPTAB · Mar 31, 2026 · IPR2025-00216 · APJ John D Hamann · IPR · Adverse judgment
The Board granted the Patent Owner’s request for adverse judgment after disclaimer of claims 1–20.
RulingsAdverse judgment- Adverse judgmentAdverse judgmentGranted
“Our Rules provide that “[a] party may request judgment against itself at any time during a proceeding,” and that “[a]ctions construed to be a request for adverse judgment include: . . . [c]ancellation or disclaimer of a claim such that the party has no remaining claim in the trial.” 37 C.F.R. § 42.73(b)(2). Such is the case here. Thus, we grant Patent Owner’s unopposed Request for Adverse Judgment.” slip op. at 2
NonePatents in suitUS 11,487,138 - Western Digital Technologies, Inc. v. Godo Kaisha IP Bridge 1Some claims unpatentablePTAB · Mar 27, 2026 · IPR2024-01447 · APJ Sheila F Mcshane · IPR · Final written decision
Claims 1–2 are unpatentable as obvious over each Bowen-based combination; claims 3–4 were not shown unpatentable, and the Nagahama-based grounds failed for all claims.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In determining the level of ordinary skill in the art, various factors may be considered, including the “type of problems encountered in the art; prior art solutions to those problems; rapidity with which innovations are 5 Nagahama, EP 1391942 A1, published February 25, 2004 (Ex. 1027, “Nagahama”). made; sophistication of the technology; and educational level of active workers in the field.” In re GPAC Inc., 57 F.3d 1573, 1579 (Fed. Cir. 1995) (citation omitted). The level of ordinary skill in the art is also reflected by the prior art of record. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001). Consistent with the Institution Decision (Dec. 7), we adopt the assessment offered by Petitioner as it is consistent with the ’134 patent and the asserted prior art. Patent Owner does not dispute that Dr. Bokor is qualified as a person of ordinary skill in the art in accordance with the assessment adopted. See Tr. 90:9–15. Patent Owner, however, questions Dr. Bokor’s knowledge on the formation of crystalline materials and seeks to exclude his related testimony. See PO Resp. 1–2, 27; PO Mot. Excl. 12–15. We address this issue infra Section V.” slip op. at 7
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner “submits the claim terms should be given their plain and ordinary meaning and no claim construction is necessary to find the claims unpatentable.” Pet. 24. Patent Owner does not raise any claim construction issues in its Response. See generally PO Resp. We determine that we need not expressly construe any claim terms to resolve the parties’ disputes. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 9
- Strike new argumentNew argument consideredDenied
“A reply may only respond to arguments raised” in the patent owner response. 37 C.F.R § 42.23(b). The Consolidated Trial Practice Guide states that responding “does not mean proceed[ing] in a new direction with a new approach,” and “[w]hile replies . . . can help crystalize issues for decision, a reply . . . that raises a new issue or belatedly presents evidence may not be considered,” that is, “Petitioner may not submit new evidence or argument in reply that it could have presented earlier, e.g. to make out a prima facie case of unpatentability.” Consolidated Trial Practice Guide § II.I (last updated Dec. 12, 2025) (“CTPG”), available at https://www.uspto.gov/patents/ptab/trial-practice-guide. We are not persuaded by Patent Owner’s assertions that Petitioner’s reply arguments on Parkin should not be considered. As discussed supra Section II.D.3.i above, the Petition includes the assertion that if Parkin’s CoFeB electrodes were used to modify Bowen, the MgO polycrystalline or single-crystal layer would still have the same 001 orientation. Pet. 33–34 (citing Ex. 1024 ¶ 129; Ex. 1062, 9:58–10:2, 18:49–51; Ex. 1005, 4:30–32). Petitioner’s support in the Petition references disclosures relating to Parkin’s Figure 3A (Ex. 1062, 18:49–51), which discloses a MgO(100) tunnel barrier, and the Petition also notes that the structure of Figure 3A may be inverted. Pet. 40 (citing Ex. 1062, 17:7–10). Patent Owner’s arguments, in large part, are related to Petitioner’s arguments in the Reply relating to Parkin’s Figure 11. Parkin’s Figure 11 is an embodiment where the structure of the devices of Figure 3A is inverted. See Ex. 1062, 22:29–33. We do not find that Petitioner’s arguments that are at issue in the Reply represent a new direction in its approach—the Petition is clearly based on the assertion that if Parkin’s CoFeB electrodes are used in Bowen, the device would have a MgO(001) tunnel barrier layer. Further, the Petition refers to Parkin’s disclosure that the device in Figure 3A may be inverted, which would be encompassed by the Figure 11 embodiment. Moreover, in the Institution Decision, we invited additional briefing on whether Parkin’s storage magnetic electrode was an amorphous ferromagnetic electrode, which relates to Parkin’s Figure 11 (Dec. 28–29). We are also not persuaded by Patent Owner’s argument that the Petition’s assertions do not correspond to what Petitioner argues in the Reply because they were referred to in the section pertaining to limitation 1[e]. The Petition includes a cross-reference in the limitation 1[d] discussion on the tunnel barrier layer limitation: “if Sunai’s or Parkin’s CoFeB electrodes are used as described in Claims 1[e] and 2 in this Ground, one of skill would understand that the MgO . . . would still have the same (001) orientation.” Pet. 33. Further, Petitioner’s arguments in its Reply properly respond to arguments made on contested issues. Patent Owner’s contentions on the merits in its Response are largely based upon the assertion that the modified MTJ of Bowen would not have a MgO(001) layer as claimed. See PO Resp. 4–10, 18–48. Petitioner’s reply arguments on Parkin relate to whether there would be a MgO(001) layer in its structure, so we find that Petitioner’s arguments on Parkin in its Reply (Pet. Reply 2–5) and the related evidence are appropriately responsive. slip op. at 17
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner
“We find that there is sufficient evidence in support of Petitioner’s assertion of the rationale to replace Bowen’s electrodes with CoFeB and anneal them. As discussed supra Section II.D.ii.2, Parkin’s Figure 11 depicts and describes a storage electrode that may be composed of amorphous CoFeB, with the formation of a MgO(001) barrier layer atop it. See Ex. 1062, 22:29–66. Patent Owner argues that Parkin’s benefits are because its CoFeB electrode is amorphous (PO Resp. 51–52), but this is not accurate. In Parkin, the CoFeB amorphous electrode crystallized at the interface layer between the barrier and the electrode. Id. at 19:6–19. Parkin discloses that higher TMRs were attributable to the crystallization of CoFeB. Id. at 18:63–19:22. Parkin also discloses that its completed CoFeB- MgOH(001)-CoFeB device was annealed with resulting high TMRs. Id. at 17:60–18:16. These disclosures provide support that one of skill in the art would have been motivated to replace Bowen’s electrodes with CoFeB and anneal to crystallize them because of the known improvements of TMR. Additionally, Parkin’s disclosures support that the results of the combination would have been predictable. That is, Parkin actually discloses an amorphous CoFeB electrode, formation of a MgO(001) tunnel barrier on the amorphous electrode, and annealing the assembly, with a resulting high TMR. Accordingly, Petitioner has provided reasoning with rationale underpinning for the motivation to combine. See KSR, 550 U.S. at 415 (“[t]he combination of familiar elements according to known methods is likely to be obvious when it does no more than yield predictable results”).” slip op. at 31
Patent outcomesUS 8,405,134 mixedClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 8,405,134
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.