- Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00187 · APJ Debra L Dennett · IPR · Final written decision
Claims 1–17 are unpatentable under § 103, principally because Chang in view of Jin renders them obvious; the Jin/Feldmann grounds were not shown.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49).” slip op. at 10
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11
- Expert testimonyPatent owner expert creditedDecided for patent owner
“gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard. Without an apparent reason to modify the teachings of Jin and Feldmann to” slip op. at 19
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 17
Patent outcomesUS 10,230,009 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,230,009 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00917 · APJ Debra L Dennett · IPR · Final written decision
Claims 1–17 are unpatentable under § 103 over Chang and Jin, alone or with Seo or Watanabe; the Jin and Feldmann grounds were not shown.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’009 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’009 patent and the prior art.” slip op. at 10
- Expert testimonyPatent owner expert creditedDecided for patent owner
“We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard.” slip op. at 19
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightMotivation not foundNot shown unpatentableNot shown unpatentable
“On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 17
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentableUnpatentable
“Patent Owner focuses on Chang’s description in paragraph 76 of a single configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” Resp. 42 (citing Ex. 1013 ¶ 76). In so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Id. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Chang ¶ 62; Tr. 15:20–17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 73, 217 (citing Ex. 1023 § 1). Chang also discloses that the emitter area may be formed by thermal diffusion, ion implantation or the like. Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding a tunneling layer and a base surface field area from periphery region and isolation region. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” slip op. at 32
Patent outcomesUS 10,230,009 unpatentable§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,230,009 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00006 · APJ Debra L Dennett · IPR · Final written decision
Claims 1–17 are unpatentable under § 103, principally over Chang and Jin; the Board rejected the Jin and Feldmann combinations for lack of a reason to combine.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’009 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’009 patent and the prior art.” slip op. at 10
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 26. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 116 with Pet. 26). Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” See Magnum, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard.” slip op. at 19
- Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable
“configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” Resp. 42 (citing Ex. 1013 ¶ 76). In so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Id. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Chang ¶ 62; Tr. 15:20–17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 73, 217 (citing Ex. 1023 § 1). Chang also discloses that the emitter area may be formed by thermal diffusion, ion implantation or the like. Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding a tunneling layer and a base surface field area from periphery region and isolation region. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” slip op. at 32
Patent outcomesUS 10,230,009 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,230,009 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00918 · APJ Avelyn M Ross · IPR · Final written decision
Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board rejected the Jin and Feldmann based grounds for lack of a reason to combine without hindsight.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16
- Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable
“Patent Owner focuses on Chang’s description in paragraph 76 of a single configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” PO Resp. 42–43 (citing Ex. 1013 ¶ 76). But, in so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Ex. 1013 ¶ 62; Tr. 15:20– 17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 70–81, 91–96, 200 (citing Ex. 1026 § 1 and stating that “[b]oth Chang and Jin likewise teach backside isolation regions”). Chang also discloses that the emitter area may be formed by “thermal diffusion, ion implantation or the like.” Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Pet. Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding the second tunneling layer and a base surface field area from periphery region and isolation portion. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art “reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” Ex. 1003 ¶ 201.” slip op. at 33
Patent outcomesUS 9,722,104 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,722,104 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00186 · APJ Avelyn M Ross · IPR · Final written decision
Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board found the combination disclosed the claimed isolation portion and supported the challenged claims.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached
“C. Claim Construction We construe claim terms according to the standard set forth in Phillips v. AWH Corp., 415 F.3d 1303, 1312–17 (Fed. Cir. 2005) (en banc); 37 C.F.R. § 42.100(b). Under Phillips, we give claim terms “their ordinary and customary meaning.” Phillips, 415 F.3d at 1312. “[T]he ordinary and customary meaning of a claim term is the meaning that the term would have to a person of ordinary skill in the art in question at the time of the invention.” Id. at 1313. “Importantly, the person of ordinary skill in the art is deemed to read the claim term not only in the context of the particular claim in which the disputed term appears, but in the context of the entire patent, including the specification.” Id. Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10
- Expert testimonyPetitioner expert discountedPatent owner expert creditedMixed
“edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001” slip op. at 18
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16
Patent outcomesUS 9,722,104 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,722,104 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00007 · APJ Avelyn M Ross · IPR · Final written decision
Claims 1–11 are unpatentable under §103 over Chang and Jin because the combination teaches the claimed isolation portion and the claimed tapering.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedOther
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightTeaching away not foundNot shown unpatentable
“On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16
- Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner
“However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide.” slip op. at 18
Patent outcomesUS 9,722,104 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,722,104 - Qualcomm Incorporated v. Cobblestone Wireless, LLCSome claims unpatentablePTAB · Mar 5, 2026 · IPR2024-01336 · APJ Russell E Cass · IPR · Final written decision
Claims 1–4, 6–9, 24, and 25 are unpatentable; claims 10, 13, 14, 17, and 21–23 were not shown unpatentable, principally due to missing limitations or insufficient motivation to combine.
RulingsFinal written decision- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner
“information” should be given its plain and ordinary meaning as “data,” and that Patent Owner’s narrower construction of “first information” and “second information” lacks sufficient support in the intrinsic record. We agree with Petitioner that the ’802 patent Specification defines “information” as data when it uses the phrase “information (i.e., data).” See Ex. 1001, 5:60–62 (“Information (i.e., data) to be transmitted may be received in a baseband digital system 250, such as a wireless digital baseband processor.” (emphasis added)), 11:30–32 (“In this example, the signals 911 and 912 carry the same information (data).” (emphasis added)). As the Federal Circuit has explained, a “specification’s use of ‘i.e.’ signals an intent to define the word to which it refers.” Edwards Lifesciences LLC v. Cook Inc., 582 F.3d 1322, 1334 (Fed. Cir. 2009). slip op. at 13
- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableNot shown unpatentableMixed
“argument based on Fernandez alone, we find that Petitioner has not provided a sufficient evidentiary basis to support a motivation to remove the amplification from each of Fernandez’s signal generators 10A-10E and add a single power amplifier instead. See Pet. 76–77 Ex. 1003 ¶ 235. Petitioner’s only rationale for this modification to Fernandez is that “[a] single amplifier has several advantages compared to multiple amplifiers, including lower complexity, a single (vs. multiple) potential point of failure, and lower cost,” and that one of ordinary skill “would have found a single amplifier to be a simple matter of design preference.” Pet. 76–77. Dr. Almeroth simply repeats these cursory allegations without providing any further explanation or evidentiary support. Ex. 1003 ¶ 235. Moreover, Dr. Cooklev provides credible testimony that replacing Fernandez’s amplification in signal generators 10A–10E with a single amplifier would not necessarily have the advantages that Petitioner suggests. See Ex. 2013 ¶¶ 99, 104–105. For example, Dr. Cooklev testifies that a single amplifier would need to have a wider bandwidth than the multiple amplifiers used in Fernandez, which could cause potential stability issues. Id. ¶ 105. According to Dr. Cooklev, this wider bandwidth would require more circuit elements, and thus would not provide the reduction in space usage and power consumption that Petitioner asserts. Id. According to Dr. Cooklev, Montojo also points to several “substantial, and potentially impractical, drawbacks” of using a single amplifier for multiple signal generators, including power constraints imposed by spectral emission requirements and on-board battery capacity. Id. ¶ 104 (citing Ex. 1006 ¶¶ 7– 8). In light of this testimony, which we find credible, Petitioner has failed to provide sufficient explanation or evidence to support its assertion that one of ordinary skill would have found it obvious to replace the multiple amplifiers in Fernandez’s signal generators with a single amplifier.” slip op. at 65
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable
“argument based on Fernandez alone, we find that Petitioner has not provided a sufficient evidentiary basis to support a motivation to remove the amplification from each of Fernandez’s signal generators 10A-10E and add a single power amplifier instead. See Pet. 76–77 Ex. 1003 ¶ 235. Petitioner’s only rationale for this modification to Fernandez is that “[a] single amplifier has several advantages compared to multiple amplifiers, including lower complexity, a single (vs. multiple) potential point of failure, and lower cost,” and that one of ordinary skill “would have found a single amplifier to be a simple matter of design preference.” Pet. 76–77. Dr. Almeroth simply repeats these cursory allegations without providing any further explanation or evidentiary support. Ex. 1003 ¶ 235. Moreover, Dr. Cooklev provides credible testimony that replacing Fernandez’s amplification in signal generators 10A–10E with a single amplifier would not necessarily have the advantages that Petitioner suggests. See Ex. 2013 ¶¶ 99, 104–105. For example, Dr. Cooklev testifies that a single amplifier would need to have a wider bandwidth than the multiple amplifiers used in Fernandez, which could cause potential stability issues. Id. ¶ 105. According to Dr. Cooklev, this wider bandwidth would require more circuit elements, and thus would not provide the reduction in space usage and power consumption that Petitioner asserts. Id. According to Dr. Cooklev, Montojo also points to several “substantial, and potentially impractical, drawbacks” of using a single amplifier for multiple signal generators, including power constraints imposed by spectral emission requirements and on-board battery capacity. Id. ¶ 104 (citing Ex. 1006 ¶¶ 7– 8). In light of this testimony, which we find credible, Petitioner has failed to provide sufficient explanation or evidence to support its assertion that one of ordinary skill would have found it obvious to replace the multiple amplifiers in Fernandez’s signal generators with a single amplifier.” slip op. at 65
- Expert testimonyPatent owner expert creditedPetitioner expert discountedOther
“We find credible and agree with Dr. Cooklev’s testimony that the predistortion signals from tables 17-1 and 17-2 “are cancelled out by Suzuki’s amplifier” 28. Ex. 2013 ¶ 50. Dr. Cooklev supports his opinion by referring to paragraph 1 of Suzuki, which states that Suzuki’s invention is directed to “a multi-band lookup table type predistorter” (such as the one implemented using lookup tables 17-1 and 17-2 in Figure 6) that “compensates for a distortion of a power amplifier.” Ex. 2013 ¶ 54; Ex. 1004 ¶ 1. Dr. Cooklev’s opinion is also supported by paragraph 3 of Suzuki, which explains that a conventional digital predistorter uses a lookup table “for linearizing non-linear characteristics of an amplifier.” Ex. 1004 ¶ 3; Ex. 2013 ¶ 54. Dr. Cooklev further supports his opinion by relying on Suzuki’s disclosure in paragraph 46 that power amplifier 28 is “subject to distortion compensation” by the predistorter, and that distortion components in the signal output by the amplifier are canceled by “distortion compensation data [that] are read out from the lookup tables 17-1 and 17-2 and provided to the adders 13-1 and 13-2, respectively.” Ex. 1004 ¶ 46; Ex. 2013 ¶ 54. And, Dr. Cooklev’s opinion is supported by Suzuki’s disclosure in paragraph 47 that the distortion compensation added by adders 13-1 and 13-2 add the distortion compensation data from lookup tables 17-1 and 17-2 “to perform distortion compensation (addition of predistortion)” to “signals to be transmitted.” Ex. 1004 ¶ 47; Ex. 2013 ¶ 54. Petitioner agrees that the distortion compensation data from lookup tables 17-1 and 17-2 “are added to the respective frequency band from” input signal ST “in order to predistort the output signal, which is then transmitted,” and does not dispute that the distortion compensation data from lookup tables 17-1 and 17-2 is ultimately cancelled out by the distortion created by amplifier 28. Pet. Reply 8. In light of the above evidence, we agree with Patent Owner that Suzuki’s distortion components from lookup tables 17-1 and 17-2 in Figure 6 (which Petitioner relies on for the first and second digital signals in limitations 10a and 10b) are cancelled out by the distortion created by power amplifier 28 before the signal is ultimately transmitted. We agree with Petitioner that these first and second digital signals include data in the form of distortion compensation data. However, because these signals are cancelled by the distortion from amplifier 28 before transmission, the data from these signals is never transmitted. Thus, the first and second digital signals identified by Petitioner (the distortion compensation data from lookup tables 17-1 and 17-2) do not comprise data “to be transmitted,” as limitations 10a and 10b require.” slip op. at 35
Patent outcomesUS 7,924,802 mixedClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 7,924,802 - Google LLC v. DH International Ltd.All claims unpatentablePTAB · Feb 10, 2026 · IPR2024-01322 · APJ Brian P Murphy · IPR · Final written decision
Claims 1–20 are unpatentable as obvious over Mooney; the Board also found Mooney combined with Lee renders the disputed limitations obvious.
RulingsFinal written decision- Skill levelSkill level board ownDecided for petitioner
“A person of ordinary skill in the art (“POSITA”) at the time of the alleged invention of the ’294 patent would have had at least a bachelor’s degree in electrical engineering, or a related field, and at least two years of experience in design, development, and/or testing of network-enabled consumer devices, and familiarity with payment cards, or the equivalent, with additional education substituting for experience and vice versa. Pet. 2 (citing Lipoff Decl. Ex. 1003 ¶ 57). “Patent Owner agrees with the Petitioner on the level of ordinary skill in the art.” Resp. 4. Patent Owner adds that a POSITA would have had “at least three years of relevant industry or research experience in wireless communication between devices.” Id. (citing Ex. 2001 ¶¶ 26–29). Mr. Zaheer testifies that a POSITA “would” slip op. at 9
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner
“The claim language and specification define and describe an “activation cue” in functional terms: a data communication from an external source is received by the cell phone and recognized as an activation cue if it causes the switching element to be assigned its first (activated) state. Ex. 1001, 9:28–31, 9:42–46, 10:14–16, 13:55–60, 14:53–59, 15:4–6, 19:20–26. Patent Owner agrees that “upon an activation cue being received by portable electronic device 10, switching element 44b switches to its activated state.” Resp. 19 (quoting Ex. 1001, 10:14–16). The activation cue may be a predetermined bit sequence, a predetermined contactless data transmission, continuously emitted, pulsed, or punctual, but these are unclaimed non-limiting embodiments of the preferred form of data transmission. Id. at 9:25–26 (“for example a predetermined bit sequence”), 11:20–22 (“One example . . . emit an activation cue in the form of a predetermined contactless data transmission”), 14:65–15:3 (continuously emitted, pulsed or punctual cue). We will not read such preferred embodiments from the specification into claim language that is not so limited. See SuperGuide Corp. v. DirecTV Enterprises, Inc., 358 F.3d 870, 875 (Fed. Cir. 2004) (care should be taken “not to import into a claim limitations that are not part of the claim”); see also In re Van Geuns, 988 F.2d 1181, 1184 (Fed. Cir. 1993) (“limitations are not to be read into the claims from the specification”); see also IQRIS Techns. LLC v. Point Blank Enterprises, Inc., 2025 WL 727717, *4 (Fed. Cir. 2025) (“It is the claims, not the preferred embodiments, that” slip op. at 15
- Claim Construction › Functional claiming / §112(f) means-plus-function › Whether §112(f) applies (Williamson, nonce words)§112(f) does not applyDecided for petitioner
“operatively linked to said electronic circuit” under 35 U.S.C. Section 112, sixth paragraph or not, the result is the same. We note there is no presumption of applying means-plus-function analysis to the switching element, because the limitation does not use the words “means for” that would mandate such claim construction treatment, and “switching” may invoke structure as well as function. See Williamson v. Citrix Online, LLC, 792 F.3d 1339, 1349–1350 (Fed. Cir. 2015) (en banc) (holding that “use of the word ‘means’ creates a presumption that § 112, ¶ 6 applies”). Regardless, we look to the meaning of the claim phrase at issue in view of the specification. We determine that the ’294 patent provides a clear, concise meaning for the switching element upon which both parties rely for construction. Patent Owner’s express agreement with Petitioner, that the claimed switching element is described in the ’294 patent as “any type of device allowing data to be conveyed according to alternate data conveyance operations in response to an activation cue being received by transceiver 18 or not,’” is particularly telling because it is not consistent with Patent Owner’s argument that the switching element means “switching of the data.” Resp. 7, 31 (citing Ex. 1001, 9:28–318). The claim language does not recite, and the specification does not describe, the switching element as a device that switches the data. Therefore, we determine the claimed “data conveyance switching element” means any type of switching device that allows data to be 8 We presume Patent Owner’s citation to “Exh. 2001, 9:28-31” on page 7 was intended to be a citation to the ’294 patent (Ex. 1001), as cited on page 31. whether or not an “activation cue” is received by the cell phone “cue receiver.”” slip op. at 21
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Plain and ordinary meaningDecided for petitioner
“[external] data exchange device” as a device with a data transceiver coupled to a circuit that carries out the function of exchanging data. Pet. 7–8 (citing Ex. 1001, 2:14–17, 4:7–14, 9:3–6; Ex. 1003 ¶¶ 67–68). As above, whether we construe the “[external] data exchange device” under 35 U.S.C. Section 112, sixth paragraph or not, the result is the same. Patent Owner, quoting the description of a data exchange device in the ’294 patent, contends that a “[external] data exchange device” “can be any sort of data exchange device comprising an electronic circuit (not shown) therein and a data transceiver 9a.” Resp. 8 (quoting Ex. 1001, 9:4–6). Patent Owner also responds to the Petition by clarifying that “[a]n external data exchange device is not a transceiver but a device with a transceiver.” Id. (citing Ex. 2001 ¶ 48). Petitioner argues in reply that Patent Owner does not contest Petitioner’s mappings of Mooney’s “cordless telephone base unit” or “cellular network infrastructure” to the claimed data exchange devices, such that no construction is necessary to resolve the dispute. Reply 5 (citing Resp. 16–37; Wellman, Inc. v. Eastman Chem. Co., 642 F.3d 1355, 1361 (Fed. Cir. 2011)). Limitations [1.c] and [1.d] recite “a first [second] data transceiver operatively linked to said electronic circuit [in the cell phone],” both of which are defined functionally as “for exchanging data between said electronic circuit [in the cell phone] and a first [second] external data exchange device over a first [second] communication link.” Nothing in the the other independent claims, further limits the form or function of the “[external] data exchange device,” although a device external to the cell phone may invoke additional structure. We determine the plain meaning of “[external] data exchange device” as claimed and described in the ’294 patent governs: any [external] device that comprises an electronic circuit and data transceiver for exchanging data with the electronic circuit in the cell phone over a communication link. slip op. at 22
Patent outcomesUS 9,022,294 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,022,294 - Reed Semiconductor Corp. v. Monolithic Power Systems, Inc.All claims unpatentablePTAB · Jan 22, 2026 · IPR2024-01158 · APJ Ken B Barrett · IPR · Final written decision
Claims 1–5, 7–15, 17, and 18 are unpatentable: claims 1–4, 9–14, 17, and 18 as anticipated by Tateishi, and claims 5, 7, 8, and 15 as obvious over Tateishi.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“We discern no material difference between the parties’ definitions. Petitioner’s definition is consistent with the level of ordinary skill reflected in the prior art references of record. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (recognizing that the prior art itself may reflect an appropriate level of skill in the art). For purposes of this decision, we apply Petitioner’s definition of the person of ordinary skill in the art. We note, however, that were we to adopt Patent Owner’s assessment, the outcome of this Decision would be the same.” slip op. at 13
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner
“After considering the parties’ arguments and evidence, we determine that Patent Owner has not offered persuasive evidence that a person of ordinary skill in the art reading the claims in light of the Specification would understand the plain and ordinary meaning of “control signal” to be as narrow as Patent Owner proposes. We do not construe the claims such that the “control signal” must be the exclusively controlling factor of a component, as Patent Owner urges. Petitioner’s position, on the other hand, is consistent with the evidence of record. We construe “control signal” as having its plain and ordinary meaning, namely a signal configured to control a circuit component. D. The Asserted Anticipation of Claims 1–4, 9–14, 17, and 18 by Tateishi” slip op. at 24
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable
“We determine that Petitioner has demonstrated by a preponderance of the evidence that Tateishi discloses the “control signal” recited in limitations 1B2 and 1D of independent claim 1.” slip op. at 37
- BurdenNot shown unpatentable
“based on the Tateishi application publication (Ex. 1007), that the Tateishi Patent (Ex. 1005) also anticipates claims 1–4, 9–14, 17, and 18. See Pet. 23–24 (“The Tateishi Patent is also prior art under (pre-AIA) §102(e)”; identifying Ground 1 as anticipation “under §102 by Tateishi and/or the Tateishi Patent”). However, we are unable to locate in the Petition or Petitioner’s Reply a discussion of or citation to the Tateishi Patent other than under the Petitioner’s heading “Identification of Challenge and Relief Requested” on pages 23 and 24 of the Petition. Cf. id. at i–x (Table of Contents identifying a section of the Petition discussing the Tateishi (Application) anticipation ground but not a section discussing a Tateishi Patent anticipation ground). Although the issued patent may be substantively identical to the published application, Petitioner does not assert that, and we decline to compare the documents to determine whether that is the case. In light of Petitioner’s silence on the alternative ground, Petitioner has not demonstrated by a preponderance of the evidence that the Tateishi Patent anticipates 1–4, 9–14, 17, and 18.” slip op. at 47
Patent outcomesUS 9,041,377 unpatentableClaim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,041,377 - PTAB · Jan 14, 2026 · PGR2025-00059 · APJ Devon Zastrow Newman · PGR · Institution
The Board instituted post-grant review of claims 1–4 on all four asserted grounds, finding a sufficient preliminary showing of obviousness and lack of enablement.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“V. CONCLUSION Petitioner has, at this stage, established that it will more likely than not prevail in showing that at least one of the challenged claims is unpatentable. This determination is, however, based on a preliminary record and is not final on any issues of patentability. We will make a final determination on the patentability of the challenged claims, as necessary and applying the preponderance of the evidence standard, based on a fully developed record through trial. VI. ORDER In consideration of the foregoing, it is hereby: ORDERED that, pursuant to 35 U.S.C. § 324(a) post grant review of claims 1–4 of the ’233 patent is hereby instituted on the grounds set forth in the Petition, commencing on the entry date of this Order, and pursuant to 35 U.S.C. § 324(d) and 37 C.F.R. § 42.4, notice is hereby given of the institution of a trial; and” slip op. at 40
- Skill levelSkill level petitioner adoptedDecided for petitioner
“Patent Owner does not proffer a description of a POSA. See generally, Prelim. Resp. For the purposes of this decision, on the record at this time, we find that Petitioner’s definition appears consistent with the level of skill shown in the prior art references of record, and apply it herein. See Daiichi Sankyo Co. v. Apotex, Inc., 501 F.3d 1254, 1256 (Fed. Cir. 2007). We invite the parties to further address the definition of a POSA during trial should they find it necessary.” slip op. at 7
- Expert testimonyPetitioner expert discountedDecided for patent owner
“In addition, the opinion stated in the Pomper Declaration that “the term of ‘low molecular weight’ is well accepted in the chemical arts” and the declarant “recognize[s] that low molecular weight compounds would have a molecular weight of typically from about 50 Daltons to about 1,500 Daltons” is offered by a co-inventor. We, as factfinder, have discretion to weigh the credibility of expert witnesses and to give each item of evidence such weight as appropriate. See In re Am. Acad. of Sci. Tech Ctr., 367 F.3d 1359, 1368 (Fed. Cir. 2004) (“[T]he Board is entitled to weigh the declarations and conclude that the lack of factual corroboration warrants discounting the opinions expressed in the declarations.”). In this case, we find that the published references on metabolites do not support the opinion. In re Am. Acad. of Sci. Tech Ctr., 367 F.3d at 1368 (“[T]he Board is entitled to weigh the declarations and conclude that the lack of factual corroboration warrants discounting the opinions expressed in the declarations.”) US-121, of which Dr. Pomper is lead inventor, also uses the term “low molecular weight”—without further characterization of the term—and is uninformative as to the meaning of the term. See Ex. 1006, ¶ 12. In addition, Patent Owner’s definition does not appear to apply to all compounds claimed in US-121.5” slip op. at 11
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner
“limited to Patent Owner’s proposed “from about 50 Daltons to about 1,500 Daltons.” The cited evidence relied on in the Pomper Declaration to define “low molecular weight” as a term well accepted in the chemical arts relates to metabolomics and metabolites. See Ex. 1002, 169, (specifically, ¶ 17 of Dr. Pomper’s declaration). Patent Owner admits that Dr. Pomper’s testimony is about molecules that differ from the claimed imaging and radiotherapeutic agents targeting FAP-α, but argues that the testimony is still relevant for purposes of explanation. Prelim Resp. 21. While it may be relevant, the testimony is not persuasive in light of the Specification. We find the uncontested fact that several of the B moieties alone—without the A moiety or L linker—specifically identified in the ’233 patent fall outside of Patent Owner’s proposed definition persuasive, as we normally do not interpret claim terms in a way that excludes examples disclosed in the specification. See, e.g., Verizon Servs. Corp. v. Vonage Holdings Corp., 503 F.3d 1295, 1305 (Fed. Cir. 2007) (rejecting proposed claim interpretation that would exclude disclosed examples in the specification). The cases cited by Patent Owner supporting that a claim term may be construed to exclude embodiments where the prosecution history supports such construction are factually distinguishable from the instant case as they regard instances of specific prosecution history disclaimer, clear prosecution disavowal, or relate to a specific definition of the terms in the Specification for the term being construed. Here, “low molecular weight” is not defined in the Specification, but, as Petitioner argues (see Pet. 21–25) is characterized as “demonstrat[ing] faster pharmacokinetics and a higher specific signal within clinically convenient times after administration” and that it “can be synthesized in radiolabeled form more easily.” Ex.1001, 13:33–50, 14:56– 16:14, 17:9–20. We are persuaded by the testimony of Dr. Zeglis, Petitioner’s declarant, that compounds weighing over 1500 Da may share those same behaviors, along with certain identified B moieties disclosed as embodiments. See Ex. 1003 ¶ 83.” slip op. at 10
Claim construction§ 103 obviousness§ 112 disclosurecites KSR · GrahamPatents in suitUS 12,115,233
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.