• Dr. Squatch, LLC v. The Procter & Gamble CompanyAll claims unpatentable
  PTAB · Jan 28, 2026 · IPR2024-01174 · APJ Susan L C Mitchell · IPR · Final written decision

  Claims 1–8 and 10–23 are unpatentable: the Board found claims 1–15 anticipated or obvious over the asserted grounds and claims 16–23 obvious over the Native combination.

  RulingsFinal written decision

  • Expert testimonyPetitioner expert creditedPatent owner expert discountedOther

    “argument that the prior art fails to enable a stable deodorant stick. Rather, we are persuaded by Petitioner that Lesniak sufficiently teaches compositions with the relevant ingredients and achieves stable compositions through the use of a second wax having a melting point of 73 to 90° C. Reply 6–7 (citing Ex. 1003, 1:39–54). For example, Lesniak’s compositions (nos. 8 and 11) that used such a second wax, namely CastorWax MP80, are disclosed as sufficiently stable. Ex. 1003, Table 2. Here, we further credit the testimony of Dr. Michniak-Kohn that Lesniak teaches how to make stable compositions by including a secondary wax, such as castor wax, with a sufficiently high melting point. Ex. 1003, 1:39-54, 5:23-32, Table 2. Both of the compositions (nos. 8 and 11) tested by Lesniak that had such a wax passed the stability tests. Id. Ex. 1086 ¶ 7; see also Reply 6 (“Lesniak overcame any stability issues, as it expressly discloses compositions that are ‘physically stable at high and low temperatures.’”) (citing Ex. 1003, 5:23–32).” slip op. at 22

  • Skill levelSkill level petitioner adoptedOther

    “Petitioner proposes that a person of ordinary skill in the art (“POSA” or “POSITA”) at the time of the invention “would have (1) at least a B.S. or equivalent degree; and (2) at least two years of experience in cosmetics formulations.” Pet. 17 (citing Ex. 1002 ¶¶ 27–29). Patent Owner does not dispute Petitioner’s proposal about the POSA’s qualifications at this stage of the proceeding. PO Resp. 10. For this Decision, we adopt and apply Petitioner’s proposal above, which does not appear to be inconsistent with the level of skill reflected in the asserted prior art.” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Preamble limiting or notPreamble limitingDecided for patent owner

    “Patent Owner asserts that the preamble of independent claim 1, 16, and 20 reciting “a deodorant stick” is limiting” as it provides antecedent basis for the recitation of “said deodorant stick being free of an aluminum salt” for each independent claim. PO Resp. 7–10. Patent Owner also points to dependent claims 6–9 as relying on the preamble reciting “a deodorant stick” as antecedent basis for claim elements. Id. at 9. We agree. Petitioner does not provide argument to the contrary. See, e.g., Pet. 19 (arguing that Lesniak discloses a deodorant stick in the form of an antiperspirant stick). We determine that no express construction of any claim term is necessary to determine whether to institute inter partes review. Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))). To the extent further discussion of the meaning any claim term is necessary to our decision, we provide that discussion below in our analysis of the asserted grounds of unpatentability.” slip op. at 8

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

    “We find that the evidence of record fails to support Patent Owner’s argument that the prior art fails to enable a stable deodorant stick. Rather, we are persuaded by Petitioner that Lesniak sufficiently teaches compositions with the relevant ingredients and achieves stable compositions through the use of a second wax having a melting point of 73 to 90° C. Reply 6–7 (citing Ex. 1003, 1:39–54). For example, Lesniak’s compositions (nos. 8 and 11) that used such a second wax, namely CastorWax MP80, are disclosed as sufficiently stable. Ex. 1003, Table 2. Here, we further credit the testimony of Dr. Michniak-Kohn that Lesniak teaches how to make stable compositions by including a secondary wax, such as castor wax, with a sufficiently high melting point. Ex. 1003, 1:39-54, 5:23-32, Table 2. Both of the compositions (nos. 8 and 11) tested by Lesniak that had such a wax passed the stability tests. Id. Ex. 1086 ¶ 7; see also Reply 6 (“Lesniak overcame any stability issues, as it expressly discloses compositions that are ‘physically stable at high and low temperatures.’”) (citing Ex. 1003, 5:23–32). Having considered the parties’ positions and evidence of record, summarized above, we determine that Lesniak provides sufficient disclosure to enable a person of ordinary skill in the art to formulate deodorant stick within the parameters of claim 1. Therefore, for the reasons discussed above, we conclude that Petitioner has proved by a preponderance of evidence that Lesniak anticipates claim 1.” slip op. at 22

  Patent outcomesUS 11,497,706 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites KSR · Graham
  Patents in suitUS 11,497,706
• Ascend Elements, Inc. v. Duesenfeld GmbHInstitution denied
  PTAB · Oct 10, 2025 · PGR2025-00037 · APJ Kevin W Cherry · PGR · Institution

  The Board denied institution of PGR on claims 1–14 because Petitioner did not show that any challenged claim was more likely than not unpatentable.

  RulingsInstitution decision

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied

    “information presented in the petition filed under [35 U.S.C. §] 321 . . . demonstrates that it is more likely than not that at least 1 of the claims challenged in the petition is unpatentable.” 35 U.S.C. § 324(a). For the reasons set forth below, we determine that Petitioner has failed to demonstrate that it is more likely than not that at least one of claims 1–14 of the ’463 patent is unpatentable. Accordingly, we deny institution of a postgrant review of claims 1–14 based on the grounds set forth in the Petition.” slip op. at 2

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that one of ordinary skill in the art “would have had at least a Bachelor’s degree in electrical engineering, material science, chemical engineering, or an equivalent field, as well as at least 2 to 3 years of academic or industry experience in the recycling or processing of lithiumion batteries. Additional formal education focusing on processing of lithium batteries may substitute for practical experience and additional practical experience can substitute for less education.” Pet. 10–11. Patent Owner does not contest this definition of a person of skill in the art. See Prelim. Resp. 11. For purposes of this Decision, we adopt Petitioner’s assessment of the level of ordinary skill in the art, as, on the present record, it appears consistent with the ’463 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 8

  • Expert testimonyPetitioner expert discountedPatent owner expert creditedDecided for patent owner

    “distinct from “comminute[ion],” Petitioner offers only the testimony of its expert, Mr. Juzkow, who equates Tomioka’s “cutting” with “comminute[ion].” See Ex. 1003 ¶ 121. However, Mr. Juzkow provides insufficient reasoning to support his conclusion, particularly given the intrinsic and extrinsic evidence discussed above. In contrast, Patent Owner’s expert, Mr. Dantam, provides extensive reasoning, supported by citations to other evidence, to support his conclusion that Tomioka’s “dismantling” is not the claimed “comminution.” Thus, we give more weight to Mr. Dantam’s testimony than Mr. Juzkow’s testimony. Weighing this evidence all together, we find that Petitioner has failed to show that it is more likely than not that Tomioka’s teaches the claimed comminution under Petitioner’s first theory.” slip op. at 15

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundTeaching away not foundNot shown unpatentable

    “obvious. Pet. 34–35. However, we agree with Patent Owner that Petitioner has also failed to show that it is more likely than not that Tomioka renders this limitation obvious. See Prelim. Resp. 28–31. To begin with, Petitioner’s contentions lack sufficient reasoning explaining why a person of ordinary skill would have modified Tomioka in the manner proposed. “[R]ejections on obviousness grounds cannot be sustained by mere conclusory statements; instead, there must be some articulated reasoning with some rational underpinning to support the legal conclusion of obviousness.” In re Kahn, 441 F.3d 977, 988 (Fed. Cir. 2006). Petitioner merely asserts that a person of ordinary skill in the art could use the roller system in place of the dismantling disclosed for the embodiments in Figures 19 and 20. On this record, we find this bare contention insufficient. actual disclosure of Tomioka. The rollers in Tomioka are used to separate the “battery body” from the “resin package enclosing the battery body,” and Tomioka specifically discloses that this technique is designed to “avoid damaging the battery body.” Ex. 1005 ¶¶ 25, 26, 29; Ex. 2011 ¶¶ 72–73. Thus, there is a significant difference between what Tomioka teaches and what Petitioner proposes to use the roller system to do. In addition, as Patent Owner points out, Tomioka specifically discloses there are risks associated with mechanically crushing battery packs, such as “risk of sparking due to residual voltage if the battery units are damaged in the process.” Ex. 1005 ¶ 5. Although we do not agree with Patent Owner that this amounts to a “teaching away,” see In re Gurley, 27 F.3d 551, 553 (Fed. Cir. 1994), we do believe that this teaching suggests a trade off that should be weighed in determining whether to make the modification, see Medichem S.A. v. Rolabo S.L., 437 F.3d 1157, 1165 (Fed. Cir. 2006). However, Petitioner has failed to account adequately, if at all, for this trade off. Thus, we find that Petitioner has failed to show that it is more likely than not that Tomioka accounts for the claimed “comminuting.”” slip op. at 15

  § 103 obviousness§ 112 disclosurecites Phillips · Graham · Nautilus
  Patents in suitUS 12,119,463
• Innoscience (Zhuhai) Technology Company, Ltd / Innoscience America, Inc. v. Efficient Power Conversion CorporationAll claims unpatentable
  PTAB · Mar 18, 2025 · IPR2023-01381 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 1–3 and 7–9 are unpatentable as obvious over Uemoto and Smith; the motion to amend is granted, and proposed substitute claims 13 and 14 are not shown unpatentable.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “In order to determine whether an invention would have been obvious at the time the application was filed, we consider the level of ordinary skill in the pertinent art. Graham, 383 U.S. at 17. In assessing the level of ordinary skill in the art, various factors may be considered, including the “type of problems encountered in the art; prior art solutions to those problems; rapidity with which innovations are made; sophistication of the technology; and educational level of active workers in the field.” In re GPAC, Inc., 57 F.3d 1573, 1579 (Fed. Cir. 1995) (quotation omitted). Petitioner contends a person of ordinary skill in the art “would have possessed at least a four-year degree in electrical engineering, chemical engineering, physics, or material science, or a closely related field, and at least two years of experience in semiconductor device design or fabrication, including the processing of semiconductor materials, analysis of device operation, or the development of new device topologies.” Pet. 5–6. Petitioner contends “[a]dditional education could substitute for professional experience and vice versa.” Id. at 6. Patent Owner contends that a person of ordinary skill in the art would have had “at least a four-year degree in electrical engineering, physics, material science, or a closely related field, and three years of professional work experience in the epitaxial growth, design, and fabrication of semiconductor electronic devices, including those of GaN.” PO Resp. 7 (citing Ex. 2009 ¶ 82). Upon review of the evidence of record and the parties’ arguments, we adopt Petitioner’s definition of the person of ordinary skill in the art as it is consistent with the prior art of record. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (holding that the prior art itself can reflect the appropriate level of ordinary skill in the art). We note, however, that the conclusions reached in this Decision would be the same under either proposed definition of the ordinarily skilled artisan. See Ex. 2009 ¶ 83 (Dr. Schubert testifying that his opinions would be the same under either proposed definition); Ex. 1033 ¶ 9 (Dr. Shealy testifying that the differences in proposed definitions of the ordinarily skilled artisan “would not change the outcome of the invalidity analysis in any material manner”); PO Resp. 7; Pet. Reply 1.” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for patent owner

    “compensated GaN layer above the barrier layer, and a gate contact above the compensated GaN layer.” Ex. 1001, 5:12–18. Petitioner contends the term “compensated” indicates that the step of compensating the GaN layer has already occurred, such that the term “compensated GaN layer” should be construed as a “‘[d]oped GaN layer formed with a step to passivate its impurities’ which is a ‘product-by-process’ limitation.”5 Pet. 12–14. And, because compensation with hydrogen was the “critical step” distinguishing the claims from the prior art, and because hydrogenation in as-grown III-nitride materials had been well known for over a decade by 2009, Petitioner contends “compensated” “cannot be interpreted as mere hydrogen presence in as-grown material, a well-known property of doped GaN.” Id. at 15. Patent Owner contends “compensated GaN material” should be construed as “a semiconductor GaN gate material in which one type of impurity (for example, donor) cancels the electrical effects of the other type of impurity (for example, acceptor).” PO Resp. 11 (citing Ex. 2009 ¶ 92) (emphasis added). Patent Owner contends this construction is consistent with the IEEE dictionary, which defines “compensated semiconductor” as 5 Given that product-by-process steps in a device claim are not entitled to patentable weight, Petitioner contends “the prior art only need show a material with passivated impurities to show unpatentability, not the step to achieve it.” Pet. 15–16. “[a] semiconductor in which one type of impurity or imperfection (for example, donor) partially cancels the electric effects of the other type of impurity or imperfection (for example, acceptor).” PO Resp. 14 (quoting Ex. 2004). Patent Owner contends its construction is also consistent with the written description of the ’294 patent, which explains that a compensated GaN material is part of the gate and includes a p-type impurity that imparts an electrical effect (i.e., conductivity), as well as a second impurity, e.g., hydrogen, that partially cancels the electrical effect of the p-type impurity, rendering the layer semi-insulating. Id. at 14–15 (citing Ex. 1001, 3:10–13, 3:43–45). On this record, we construe “compensated GaN layer” as “a GaN layer in which one type of impurity (for example, donor) partially cancels the electric effects of the other type of impurity (for example, acceptor).” This is consistent with the disclosures of the ’294 patent, the IEEE dictionary definition, and the construction ultimately adopted by the ITC. Ex. 2004, 3; Ex. 1049, 16–17 (ITC construing “compensated GaN layer” to mean “a GaN layer in which one type of impurity partially cancels the electrical effects of another type of impurity”); Ex. 1001, 3:43–45 (explaining that the compensated GaN layer of the ’294 patent is formed through the “passivation of a p-type impurity using hydrogen”). For the reasons set forth below, however, we decline to construe “compensated GaN layer” as a product-by-process claim term (as asserted by Petitioner), or to limit the compensated GaN layer to a gate material (as asserted by Patent Owner).” slip op. at 11

  • Claim Construction › Intrinsic evidence (Phillips canons) › Specification disavowal / 'present invention' languageDisclaimer not foundDecided for petitioner

    “There are two exceptions to the general rule that we apply the ordinary and customary meaning of a claim term: (1) when a patentee sets out a definition and acts as his own lexicographer, or (2) when the patentee disavows the full scope of a claim term either in the specification or during prosecution. See Thorner, 669 F.3d at 1365. The standards for lexicography and disclaimer, however, are “exacting.” Id. at 1366. There is no argument that the patentees acted as their own lexicographer to redefine the term “compensated GaN layer.” With respect to disavowal, a “patentee may demonstrate intent to deviate from the ordinary and accustomed meaning of a claim term by including in the specification expressions of manifest exclusion or restriction, representing a clear disavowal of claim scope.” Thorner, 669 F.3d at 1366 (quoting Teleflex, Inc. v. Ficosa N. Am. Corp., 299 F.3d 1313, 1325 (Fed. Cir. 2002)). As noted by Patent Owner, the title of the ’294 patent is, in part, “Compensated Gate MISFET” and much of the discussion of the ’294 patent is of a compensated GaN layer that is directly below the gate contact and above a barrier layer and operates in conjunction with the gate contact to control the on/off state of the transistor. PO Resp. 12–14. We are presented with insufficient argument or evidence to conclude, however, that these disclosures rise to the level of a disclaimer. For example, although the title of the ’294 patent is directed to a “Compensated Gate MISFET,” claim 1 is more broadly directed to “[a] column III Nitride transistor.” Ex. 1001, 5:12, code (54). Nor are we directed to an expression or statement of manifest exclusion in the ’294 patent that would serve to disclaim any “compensated GaN layer” that is not directly below the gate and/or that does not function in concert with the gate electrode to control the on/off state of the transistor. See Thorner, 669 F.3d at 1366. With respect to the stated goals of the invention, as noted by Patent Owner, one of the primary purposes of the compensated GaN layer of the ’294 patent is to reduce gate leakage and gate capacitance. Ex. 1001, 2:13– 19, 3:18–21 (“[U]sing a compensated semiconductor layer 38 leads to low gate leakage during device operation.”). We cannot use the goals of the invention, however, to rewrite the claims or insert terms that are not present. See Thorner, 669 F.3d at 1366. Moreover, the prior art of record indicates that a compensated GaN layer that is below the gate contact and above a barrier layer, but not part of the active gate structure, may also “decrease the leakage current between the gate and the drain.” Ex. 1006 ¶¶ 44 (“Even when a positive bias of 5 V or higher is applied to the gate electrode, no significant gate-leakage current is observed.”), 61. As such, evidence of record suggests that a person of ordinary skill in the art would have understood that one of the primary goals disclosed in the ’294 patent is achieved regardless of whether the compensated GaN layer is part of the gate, or simply in close vicinity to the gate. In view of the foregoing, we are not persuaded that the written description of the ’294 patent indicates that the “compensated GaN layer” must be part of the gate structure.” slip op. at 17

  • Obviousness (§103) › Objective indicia / secondary considerations › NexusObjective indicia no nexusDecided for petitioner

    “To be probative, Patent Owner must prove there is a nexus between the presented evidence and the merits of the claimed invention. See Demaco Corp. v. F. Von Langsdorff Licensing Ltd., 851 F.2d 1387, 1392 (Fed. Cir. 1988). A rebuttable presumption of nexus applies when the “patentee shows that the asserted evidence is tied to a specific product and that the product ‘is the invention disclosed and claimed.’” Fox Factory, Inc. v. SRAM, LLC, 944 F.3d 1366, 1373 (Fed. Cir. 2019) (quoting Demaco, 851 F.2d at 1392). “That is, presuming nexus is appropriate ‘when the patentee shows that the asserted objective evidence is tied to a specific product and that product embodies the claimed features, and is coextensive with them.’” Id. (quoting Polaris Indus., Inc. v. Arctic Cat, Inc., 882 F.3d 1056, 1072 (Fed. Cir. 2018)). If the praise is not limited to the features of the claimed invention, the patent owner may still prove nexus “by showing that the evidence of secondary considerations is the ‘direct result of the unique characteristics of the claimed invention.’” Id. at 1373–74 (quoting In re Huang, 100 F.3d 135, 140 (Fed. Cir. 1996)). Patent Owner contends that the compensated gate of the ’294 patent “was a breakthrough invention and resulted in the first commercially viable enhancement-mode GaN transistor.” PO Resp. 60 (citing Ex. 2009 ¶¶ 192– 193, 197; Ex. 2021). Patent Owner further contends that this achievement required the counter-intuitive use of a compensated gate material in the gate structure, and represented “a technological leap that laid the foundation for viable enhancement-mode GaN transistors.” Id. at 61–62. For this achievement, Patent Owner contends the inventor, Dr. Alex Lidow, received the 2015 SEMI Award. Id. at 60 (citing Ex. 2021). Upon review of Patent Owner’s evidence and the parties’ arguments, we find that Patent Owner’s objective indicia evidence is entitled to little, if any, weight. The evidence of praise relied upon by Patent Owner is not clearly linked to the claimed invention or any particular product having each of the claimed features of the ’294 patent. Ex. 2021. For example, the 2015 SEMI award was provided to Dr. Lidow “for commercialization of GaN power devices.” Id. An article explaining the award indicates that “high cost” previously “limited [the] commercial success” of GaN technologies, but Dr. Lidow was able to overcome these issues, “from resolving packaging limitations to establishing a low-cost supply chain,” “through persistence.” Id. This praise is not demonstrably linked to the claimed invention or any particular device, and does not mention the use of a compensated gate, or any other relevant feature recited in the claims. In view of the foregoing, we determine that Patent Owner’s objective evidence of non-obviousness is entitled to little, if any, weight.” slip op. at 20

  Patent outcomesUS 8,350,294 unpatentable
  Claim construction§ 103 obviousness§ 112 disclosurecites KSR · Graham
  Patents in suitUS 8,350,294
• Billerud Aktiebolag (Publ) v. Westrock MWV, LLCSome claims unpatentable
  PTAB · Mar 12, 2025 · IPR2023-01206 · APJ Elizabeth M Roesel · IPR · Final written decision

  Claims 1, 2, and 4–22 are unpatentable as obvious; claim 23 was not shown unpatentable. Substitute claims 25–26 are allowed, while 24 and 27 are denied for lack of written-description support.

  RulingsFinal written decision

  • Expert testimonyPetitioner expert discountedOther

    “Exhibits 1013 and 1014 are also not admissible as expert testimony because Mr. Wirén is not “qualified as an expert by knowledge, skill, experience, training, or education.” Fed. R. Evid. 703. “To offer expert testimony from the perspective of a skilled artisan in a patent case—like for claim construction, validity, or infringement—a witness must at least have ordinary skill in the art. Without that skill, the witness’ opinions are neither relevant nor reliable.” Kyocera Senco Indus. Tools Inc. v. Int’l Trade Comm’n, 22 F.4th 1369, 1376–77 (Fed. Cir. 2022). Mr. Wirén does not meet our definition of a person of ordinary skill in the art. See Section II.B, supra. That definition is based on the undisputed testimony of Messrs. Zotterman and Klass. Ex. 1003 ¶ 24; Ex. 2003 ¶ 26. Although Mr. Wirén has a Master’s of Science in chemical engineering, he lacks any experience or specialization in paperboard manufacturing. Ex. 2011, 12:1–10, 19:6–25, 20:2–7. We therefore agree with Patent Owner that Exhibits 1013 and 1014 are the testimony of Mr. Wirén and should be excluded from evidence because Mr. Wirén is not a person of ordinary skill in the relevant art. PO MTE 5–6, 9; Sundance, Inc. v. DeMonte Fabricating Ltd., 550 F.3d 1356, 1362 (Fed. Cir. 2008) (“Unless a patent lawyer is also a qualified technical” slip op. at 61

  • Skill levelSkill level board ownOther

    “Level of Ordinary Skill in the Art Based on the testimony of the parties’ witnesses, we determine that a person of ordinary skill in the art would have had a bachelor’s degree in paper science and engineering, chemical engineering, process engineering, mechanical engineering, or a related degree, with three to five years of experience in paperboard manufacturing, or a master’s degree in paper science and engineering, chemical engineering, process engineering, or mechanical engineering, or a similar field with a specialization in paperboard manufacturing. Ex. 1003 ¶ 24; Ex. 2003 ¶ 26. We find that the level of ordinary skill in the art, as articulated above, is consistent with the level of technical understanding and competence reflected in the ’142 Patent Specification and the asserted prior art references.” slip op. at 10

  • Claim Construction › Intrinsic evidence (Phillips canons) › Specification disavowal / 'present invention' languageTerm construed petitioner constructionDecided for petitioner

    “A claim construction that excludes a particular element is viewed as a “negative limitation.” Ethicon LLC v. Intuitive Surgical, Inc., 847 Fed. App’x 901, 907 (Fed. Cir. Mar. 15, 2021). “[S]uch exclusions must find support either in ‘the words of the claim’ or through an ‘express disclaimer or independent lexicography in the written description that would justify adding that negative limitation.’” Id. (citing Omega Eng’g, Inc. v. Raytek Corp., 334 F.3d 1314, 1323 (Fed. Cir. 2003); CCS Fitness, Inc. v. Brunswick Corp., 288 F.3d 1359, 1366–67 (Fed. Cir. 2002)). “The standards for finding lexicography and disavowal are exacting.” GE Lighting Sols., LLC v. AgiLight, Inc., 750 F.3d 1304, 1309 (Fed. Cir. 2014). “To act as its own lexicographer, a patentee must ‘clearly set forth a definition of the disputed claim term,’ and ‘clearly express an intent to define the term.’” Id. (citing Thorner, 669 F.3d at 1365). Similarly, disclaimer or disavowal requires that the specification or prosecution history demonstrate that the invention does not include a particular feature. Id. Here, we find no claim language, lexicography, or disclaimer in the ’142 Patent or its file history that would support defining a “hot-hard calender” as requiring that only one of the two rollers be heated to an elevated temperature.” slip op. at 12

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentable

    “a contact surface of said thermo-roller is heated to an elevated temperature of at least 250°F.” Petitioner shows persuasively that the temperature limitation is taught by the combination of Fugitt and Papermaking. Pet. 32–34. Fugitt discloses that “[t]he rolls of the calender may be steam heated.” Ex. 1004 ¶ 26. In a section titled “Heated Rolls,” Papermaking discloses that “Steam can be used up to 170°C [338°F] surface temperature.” Ex. 1010, 95, 98. Petitioner is thus correct that, “[w]hile Fugitt teaches that a hot calender may be steam heated, Papermaking clarifies that one of ordinary skill in the art would understand that steam heated thermo-rollers may reach up to 338°F.” Pet. 36. Based on these disclosures, we are persuaded by Mr. Zotterman’s testimony that it would have been “obvious to heat the thermo-roller of Fugitt to at least 250°F.” Ex. 1003 ¶ 159. combine Fugitt and Papermaking because of Papermaking’s status as a “trusted handbook[],” because both references disclose a method of manufacturing a paperboard structure with hot calendering,” and “because of the known advantages of heated rollers.” Pet. 36–37; Ex. 1003 ¶¶ 157, 159, 162. Petitioner’s contention is supported by Papermaking’s disclosures that, for cartonboard, “[p]recalendering is used before the coater to reduce roughness and porosity” and “[h]igh thermo roll temperatures (in some cases over 200°C) result in bulk savings because of the temperature gradient.” Ex. 1005, 80–82; see also Pet. 38; Ex. 1003 ¶ 164 (citing these disclosures). Papermaking’s disclosed range of “up to 170°C [338°F]” for steam- heated rolls (Ex. 1010, 98), overlaps the claimed range of “at least 250°F.” Patent Owner agrees. Tr. 27:11–13. “If the relevant comparison between a disputed claim limitation and the prior art pertains to a range of overlapping values, ‘. . . even a slight overlap in range establishes a prima facie case of obviousness.’” Genentech, Inc. v. Hospira, Inc., 946 F.3d 1333, 1341 (Fed. Cir. 2020) (citing In re Peterson, 315 F.3d 1325, 1329 (Fed. Cir. 2003)). “[S]uch an overlap creates a presumption of obviousness, and . . . the burden of production falls upon the patentee to come forward with pertinent evidence that the overlapping range would not have been obvious in light of the prior art.” Id. (citing E.I. DuPont de Nemours & Co. v. Synvina C.V., 904 F.3d 996, 1006, 1008 (Fed. Cir. 2018)). slip op. at 21

  Patent outcomesUS 11,293,142 mixed
  Claim construction§ 103 obviousness§ 112 disclosurecites Phillips · KSR · Graham
  Patents in suitUS 11,293,142
• Nespresso USA, Inc. v. K-Fee System GmbHAll claims unpatentable
  PTAB · Sep 10, 2024 · IPR2023-00485 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 1–10 are unpatentable as obvious over the combined disclosures of Yoakim, Jarisch, Rossi, and Castellani.

  RulingsFinal written decision

  • Skill levelSkill level board ownPetitioner expert creditedDecided for petitioner

    “have a bachelor’s degree in engineering plus five years of experience in design of mechanical beverage systems, or similar products.” Pet. 31 (citing Ex. 1003 ¶ 40). In the Institution Decision, we preliminarily determined that a person of ordinary skill in the art “would have a bachelor’s degree in engineering plus five years of experience in design of mechanical beverage systems, or similar products, as well as experience with sensors for recognizing an identifier.” Inst. Dec. 8 (emphasis added). Neither party disputes this conclusion. PO Resp. 9; see generally Pet. Reply. As such, we adopt our preliminary definition of the ordinarily skilled artisan for purposes of this Final Written Decision.” slip op. at 8

  • Expert testimonyPetitioner expert creditedPatent owner expert discountedDecided for petitioner

    “designing medical devices and components, and that those experiences represent work designing products similar to mechanical beverage systems, Patent Owner fails to direct the Board to evidence sufficient to establish that this experience, in the aggregate, amounts to at least “five years” or involved “experience with sensors for recognizing an identifier.” Inst. Dec. 8 (adopting Patent Owner’s own proposed definition of one of ordinary skill in the art); see Sur-reply 3–4 (citing Ex. 1066, 34:16–35:9; Ex. 1067, 101:3– 12, 102:20–104:9; Ex. 2017 ¶¶ 3–4, 8–10) (failing to establish adequately, if at all, how Dr. Howle’s qualifications include the requisite minimum five-year period of relevant design experience). Accordingly, we determine that Dr. Howle is not qualified to offer expert testimony from the perspective of a person having ordinary skill in the art in this proceeding.10 See Kyocera Senco Indus. Tools Inc. v. Int’l Trade Comm’n, 22 F.4th 1369, 1376–77 (Fed. Cir. 2022). The Federal Circuit has explained that “[t]o offer expert testimony from the perspective of a skilled artisan in a patent case,” including the issue of patent “validity,” the “witness must at least have ordinary skill in the art.” Id. (Board’s emphasis). “Without that skill, the witness’[s] opinions are neither relevant nor reliable.” Id. at 1377.” slip op. at 13

  • Disclosure Requirements (§112) › Written description (Ariad)Not entitled to earlier dateDecided for petitioner

    “Second, Patent Owner and Dr. Howell assert that a person of ordinary skill in the art “would have understood upon reading the second German application that the capsule features described would be intended to be combinable with each of the described embodiments.” PO Resp. 40; Ex. 2017 ¶ 61. But Patent Owner and Dr. Howell do not explain how a barcode could be used in the devices depicted in Figures 16–18, which place the detection means 2.4.2 on the outer circumference of the flange (not its underside) and rely on toothed-rings physically interacting with either the chamber, retaining arms, or a pinion. Ex. 1047, 12:22–31, 13:8–18. Indeed, the second German priority application explains that means 2.4.2 physically interacts with retaining arms 30 (embodiments of Figures 16 and 17) or a pinon (embodiment of Figure 18), and if means 2.4.2 were not present in these embodiments the capsule would either “drop through into a waste container” or could not be inserted through the insertion shaft. Id. at 12:22– 27, 13:9–12, 13:16–35 (noting that in the embodiment disclosed in Figure 18 a pinon interacts with means 2.4.2 and only when means 2.4.2 “is formed complementary to the teeth of the means” can the capsule be inserted). At no point does the second German application identify means 2.4.2 as a barcode or suggest a barcode could be used as the detection means. The second German application also states that A person skilled in the art is also aware that for example the insertion shaft may also contain a sensor, for example a camera, clear, however, that element 27 is part of the brewing chamber, and not the capsule. Ex. 1047, 12:27–31, 13:5–8, 13:21–26, 15:36. Thus, we are not persuaded that the toothed ring is in fact on the bottom side of the flange. which senses the shape of the means 2.4.2. For example, it would be possible, in the present case, for the shape of the teeth and/or the spacing between the same to be sensed. This signal, in turn, is passed to a control means, which frees, for example, the brewing chamber if the capsule is the correct one. Ex. 1047, 14:11–19. Again, despite using a camera to determine if a capsule is “the correct one,” the second German application does not suggest using a barcode in place of the toothed-ring structure, or suggest moving the location of the detection means 2.4.2 from the outer surface to the underside of the flange. This reinforces that the inventors did not contemplate using a barcode in the embodiments depicted in Figures 16–18.” slip op. at 23

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner

    “As asserted by Petitioner, Jarisch teaches how to move a code in a centrifugal brewing system to the bottom of the flange and how to configure a light-conductive material so that the detector’s light source will reach the bottom of the flange. Pet. 48–49; Pet. Reply 23–24 (Ex. 1003 ¶¶ 184–185; Ex. 1005 ¶¶ 82–84, Fig. 5). And, although Figure 61 of Yoakim discloses a flare in its brewing chamber, bodily incorporation is not required, and we are directed to no persuasive argument or evidence that Yoakim could not be configured with a straight chamber, as generally depicted in Figure 5 of Jarisch. Pet. Reply 24 (noting that Dr. Howle’s testimony on this subject is “conclusory” and depends on “bodily incorporation”). As such, we credit the testimony of Mr. Jobin that a person of ordinary skill in the art would have sought to place the code at the bottom of the flange and would have had a reasonable expectation of success in so doing.17 Ex. 1003 ¶ 184. Patent Owner further contends that Yoakim requires that the capsule holder be capable of receiving a set of multiple volume capsules and that 17 As discussed above, Mr. Jobin has extensive experience in the design of brewing devices. Conversely, Dr. Howle has limited experience in this field and is not one of ordinary skill in the art. Although Mr. Jobin’s testimony is more persuasive regardless of the discrepancy in experience between the two declarants, when this difference in design experience is considered, it only serves to increase the weight we give to Mr. Jobin’s testimony. there is a “snug fit” to avoid “unbalances.” PO Sur-reply 8 (citing Ex. 1004 ¶¶ 205, 479, 484, 507, 512). According to Patent Owner, Petitioner does not explain adequately how the use of Jarisch’s “straight chamber” with a capsule holder that does not engage with the side wall of the capsule would allow insertion of the multiple volume capsules or permit a “snug fit.” Id.; PO Resp. 28. Patent Owner’s assertion that Yoakim discloses the use of certain capsules that might not fit into a device with Jarisch’s non-flared structure is ineffective to undercut the sufficiency of Petitioner’s showing on this point. As noted by Patent Owner, Yoakim discloses the use of certain capsules which might not fit into a device with Jarisch’s non-flared structure. But Petitioner is not seeking a bodily incorporation of Yoakim and Jarisch, and other embodiments of Yoakim do not require the type of flared capsule identified by Patent Owner. Ex. 1004, Fig. 63. Moreover, we are directed to no persuasive evidence that Jarisch’s lack of contact between the capsule side wall and the holder would render the device inoperable or even less effective. Id. (citing Ex. 2019, 36:18–37:6; Ex. 1005 ¶ 23 (Jarisch explaining that its device includes a capsule holding means and that the capsule may be successfully driven in rotation). As such, we credit the testimony of Mr. Jobin that one of ordinary skill in the art would have understood how to design the chamber of Yoakim to allow reading of a barcode on the underside of the flange and that this design would allow for successfully receiving single-serve capsules and driving them in rotation. Ex. 1003 ¶¶ 182–184; Ex. 1005 ¶ 23.” slip op. at 39

  Patent outcomesUS 11,230,430 unpatentable
  § 103 obviousness§ 112 disclosurecites KSR · Graham
  Patents in suitUS 11,230,430
• Chongqing Yanmei Technology Co., Ltd. v. Terves, LLCSome claims unpatentable
  PTAB · Aug 27, 2024 · IPR2023-00521 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 19–61, 63–77, and 79 are unpatentable as anticipated by Doud; claims 78, 80, and 81 are not shown unpatentable. The contingent motion to amend is granted in part and denied in part.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art “would have at least a Ph.D. in chemistry, metallurgy, or material science or material engineering” or, in the alternative, “would have a Bachelor of Science or Master of Science degree in one of these disciplines plus experience involving the use and design of dissolvable metal alloys for use in creating tools and other downhole parts for well drilling or completion activities.” Pet. 13–14. Patent Owner does not oppose Petitioner’s contentions regarding the level of ordinary skill in the art. PO Resp. 12 n.4. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the ordinarily skilled artisan as it is consistent with the prior art of record.” slip op. at 7

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

    “With respect to claim 19, Petitioner proposes constructions for the terms “in situ precipitate” and “a plurality of particles of said in situ precipitate having a size of no more than 50 µm.” Pet. 11–12. With respect to claims 76–81, Petitioner proposes a construction for the term “wherein said additive material includes one or more metal materials selected from the group consisting of 0.1–35 wt. % copper, 0.1–24.5 wt. % nickel and 0.1–20 wt. % cobalt.” Id. at 13. Patent Owner contends no claims require construction for purposes of this Decision. PO Resp. 12 n.4, 17–18; Mot. 16–17. Upon review of the prior art of record, we determine that no claim terms require express construction for purposes of this Final Written Decision. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 8

  • Disclosure Requirements (§112) › Written description (Ariad)Written description inadequateWritten description adequateMixed

    “Ex. 2027, 20:25–21:5 (emphasis added). The disclosure that the “magnesium composite” of “[t]he present invention” “includes at least 50 wt% magnesium” is unambiguous and constitutes strong evidence that the inventors were not in possession of a magnesium composite with less than 50 wt. % magnesium, or additive concentrations above 50 wt. %. See SciMed Life Systems, Inc. v. Advanced Cardiovasular Systems, Inc., 242 F.3d 1337, 1343 (Fed. Cir. 2001) (noting that a description of the “present invention” as having a particular structure “is strong evidence that the claims should not be read to encompass the opposite structure”). Consistent with this conclusion, the original claims of the ’295 application all limited the additive material in the composite to 0.05 wt %–45 wt %. Ex. 2027, 26:1– 13, 29:9–15. Likewise, in each example where copper, nickel, or cobalt additives are used in the range recited in the proposed substitute claims, the magnesium composite is “over 50 wt% magnesium,” and any claims that do not require this range of magnesium are limited to an additive range of “about 0.05 wt%–45 wt% of said mixture.”8 Ex. 2027, 6:13–7:4, 7:16–19, 8 Written description support is considered from the view point of the ordinarily skilled artisan. Ariad Pharms., Inc. v. Eli Lilly and Co., 598 F.3d 1336, 1351 (Fed. Cir. 2010) (en banc). Patent Owner, bearing the burden to show written description support in any priority application for which it seeks the benefit of its filing date, provides no testimony from an ordinarily skilled artisan regarding written description support in the ’295 application, or any evidence to show what such an artisan would conclude from the express disclosures of the ’295 application. Lectrosonics, Paper 15 at 7; In re NTP, 654 F.3d 1268, 1276 (Fed. Cir. 2011) (noting that “a patent’s claims are not entitled to an earlier priority date merely because the patentee claims priority . . . Rather, for a patent’s claims to be entitled to an earlier priority date, the patentee must demonstrate that the claims meet the requirements of 35 U.S.C. § 120”). Where there is any ambiguity in the disclosures of the ’295 application, the absence of supporting testimony tends to cut against 26:2–31:2; see Ex. 1005 ¶¶ 12, 13, 18, 19, 16–21, 26, 28, claims 16–21, 26– 28. In view of the foregoing, we are not persuaded that Patent Owner has demonstrated that the inventors of the priority applications were in possession of a magnesium cast composite that included less than 50 wt. % magnesium, or greater than 50 wt. % additives. As proposed substitute claim 104 encompasses a magnesium cast composite with up to 90 wt. % additives, and therefore as little as 10 wt. % magnesium, Patent Owner has not demonstrated that the full scope of this claim finds written description support in any application prior to the ’915 application, filed on October 12, 2018.” slip op. at 17

  • Disclosure Requirements (§112) › Definiteness (Nautilus)DefiniteIndefiniteMixed

    “The definiteness requirement of § 112(a) is satisfied when “a patent’s claims, viewed in light of the specification and prosecution history, inform those skilled in the art about the scope of the invention with reasonable clarity.” Nautilus, Inc. v. Biosig Instruments, Inc., 572 U.S. 898, 910 (2014); see 37 C.F.R. § 42.100(b) (changing the claim construction standard used to review a claim proposed in a motion to amend from the broadest reasonable construction to the “same construction standard that would be used to construe the claim in a civil action under 35 U.S.C. [§] 282(b)”). Proposed substitute claim 104 generically requires “in situ precipitate” and also a specific type of in situ precipitate: “in situ galvanically-active intermetallic precipitate.” Mot. Appendix A. Although this claim would have best been clarified by Patent Owner after seeking preliminary guidance on its Motion to Amend, upon review of the written description, claims, and figures of the ’740 patent, as well as Patent Owner’s clarification in its Reply to the Opposition, we agree with Patent Owner that one of ordinary skill in the art would have understood that the “in situ galvanically-active intermetallic precipitate” is merely a more complete description of the “in situ precipitate” mentioned earlier in the sentence. Mot. Reply 4. As such, we do not find that this part of proposed substitute claim renders claim 104 indefinite.” slip op. at 22

  Patent outcomesUS 10,689,740 mixed
  Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Graham · Nautilus
  Patents in suitUS 10,689,740
• Daiichi Sankyo, Inc. / Astrazeneca Pharmaceuticals, LP v. Seagen Inc.All claims unpatentable
  PTAB · Jan 16, 2024 · PGR2021-00030 · APJ Jeffrey N Fredman · PGR · Final written decision

  Claims 1–5, 9, and 10 are unpatentable for lack of written description, lack of enablement, indefiniteness, and anticipation by Ogitani.

  RulingsFinal written decision

  • Skill levelSkill level board ownOther

    “respective definitions for the level of ordinary skill in the art. While there seems to be a slight difference in whether the ordinary artisan has ADC design experience obtained after a master’s degree or postdoctoral, neither party provides clear basis to explain how this will impact the analysis. Accordingly, we find the parties’ respective definitions to be equivalent and consistent with the level of ordinary skill in the art as reflected by the prior” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed petitioner constructionDecided for petitioner

    “III. CLAIM CONSTRUCTION We interpret claim terms using “the same claim construction standard” slip op. at 11

  • Disclosure Requirements (§112) › Written description (Ariad)Written description inadequateNot entitled to earlier dateUnpatentable

    “4. Analysis We note that “[i]t is not sufficient for purposes of the written” slip op. at 23

  • Disclosure Requirements (§112) › Enablement (Wands, Amgen full scope)Not enabledUnpatentable

    “4. Analysis The facts here are consistent with the situation in Amgen, which” slip op. at 76

  Patent outcomesUS 10,808,039 unpatentable
  Claim construction§ 102 anticipation§ 112 disclosurecites Phillips · Nautilus
  Patents in suitUS 10,808,039
• Nespresso USA, Inc. v. K-Fee System GmbHInstituted
  PTAB · Sep 13, 2023 · IPR2023-00485 · APJ Jon B Tornquist · IPR · Institution

  Instituted IPR of claims 1–10 on all petition grounds; Petitioner showed a reasonable likelihood that the claims would have been obvious over Yoakim, Jarisch, Rossi, and Castellani.

  RulingsInstitution decision

  • Disclosure Requirements (§112) › Written description (Ariad)Not entitled to earlier dateDecided for petitioner

    “second German priority application do not disclose every limitation of independent claims 1 and 7 of the ’430 patent. Figure 1 does not depict a barcode under the flange, but rather the use of raised areas on the side of the capsule that act as an identifier. Ex. 1047, Fig. 1. Figure 2, coupled with its associated description, might suggest that the barcode could be on the portion of the base element facing away from the membrane,9 but this figure does not disclose many of the other elements of the claim, including holding arms, a drop box, annular convexity and concavity, and a pump to supply water to the single-serve capsule. Pet. 41; Ex. 1047, 9:21–24, Fig. 2. We also determine that Patent Owner does not sufficiently demonstrate that Figures 16–18 of the second German priority application provide adequate disclosures showing that the inventors were in possession 9 We question whether the second German priority application supports placing a barcode under the flange. The application states that the barcode could “be provided on that side of the peripheral region of the basic element which is directed away from the membrane.” Ex. 1047, 9:21–24. This statement is rather ambiguous as to where the “peripheral region” is that is “directed away from the membrane.” The text goes on to explain, however, that “[t]his barcode,” i.e., the barcode that is “directed away from the membrane,” “is read by a detector 13,” which in Figure 2 is oriented to read a barcode on the top surface of the flange. Id. at 9:25–26, Fig. 2. This suggests that the barcode is not on the bottom side of the flange and that arrow 15 is pointing to the outer portion of the peripheral region that is not covered by the membrane, and not necessarily the bottom of the flange. First, the second German priority application describes the use of “an identifier” that is read by a “sensor/detection means” and then compared to a stored identifier. Ex. 1047, 2:29–31. In Figure 2 the identifier may be a barcode and the detection means is detector 13. Id. at 9:11–26. In Figures 16–18, however, element 2.4.2 is not an identifier, but rather a “a form-fitting and/or friction-fitting means and/or a detection means.” Id. at 12:22– 24 (emphasis added). As such, it is unclear how this disclosure would demonstrate possession of the disputed claim limitation, when combined with the other limitations of claims 1 and 7 as a whole. Second, it is not evident that the toothed rings of Figures 16–18 are on the underside of the flange, as asserted by Patent Owner. Prelim. Resp. 42 (asserting that a barcode “could be located on the bottom side of the flange instead of the toothed ring”); Prelim. Sur-reply 4. The second German priority application states that the “form-fitting and/or friction-fitting means and/or detection means 2.4.2” is located in the “outer region” of the peripheral region 2.4. Ex. 1047, 12:22–24. We are directed to no evidence that this “outer region” is on the bottom of the flange, and Figures 16–18 each appear to depict means 2.4.2 on, or forming, the outer circumference of the flange.11 Id. at Figs. 16–18, 6:8–11 (noting that the toothed ring is provided “on the outer circumference of the periphery”). 10 The parties dispute whether Figure 16 of the second German priority application discloses annular convexity and concavity. Pet. 42–43; Prelim. Resp. 45–46; Prelim. Reply 4–5; Prelim. Sur-reply 4. At most, the parties identify a material issue of fact with respect to these two claim elements that is best resolved on a full trial record. 11 At first blush, Figure 17A appears to show means 2.4.2 under a portion of element 27 of the capsule. Ex. 1047, Fig. 17A; Prelim. Sur-reply 4 depicted in Figures 16–18, which rely on toothed rings physically interacting with either the chamber, retaining arms, or a pinion. Ex. 1047, 12:22–31, 13:8–18. The second German priority application explains that means 2.4.2 physically interacts with retaining arms 30 (embodiments of Figures 16 and 17) or a pinon (embodiment of Figure 18), and if means 2.4.2 were not present in these embodiments, the capsule would either “drop through into a waste container” or could not be inserted through the insertion shaft. Id. at 12:22–27, 13:9–12, 13:16–35 (noting that in the embodiment disclosed in Figure 18 a pinon interacts with means 2.4.2 and only when means 2.4.2 “is formed complementary to the teeth of the means” can the capsule be inserted). Patent Owner does not sufficiently explain how a barcode could replace means 2.4.2 in these embodiments and still retain the capsule within the device or allow the capsule to enter the insertion shaft.” slip op. at 14

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundInstituted

    “First, Yoakim expressly states that the capsule may use a “barcode,” and the plain and ordinary meaning of this term is a code that satisfies the construction adopted by the district court. To the extent Patent Owner has reason to believe that Yoakim does not apply the plain and ordinary meaning of the term “barcode,” and that one of ordinary skill in the art would have understood this fact, it is encouraged to present such evidence during trial. Second, in this obviousness inquiry the question is not whether a person of ordinary skill in the art is more likely to adopt a barcode or a bitcode, but whether one of ordinary skill in the art would have seen a benefit to applying the “barcode” of Yoakim under the flange of the capsule. See Intel Corp. v. Qualcomm Inc., 21 F.4th 784, 800 (Fed. Cir. 2021) (“Our case law is clear. It’s not necessary to show that a combination is ‘the best option, only that it is a suitable option.’”). On that point, Jarisch expressly discloses the benefits of doing so. Ex. 1005 ¶ 22 (noting that applying the code at the bottom of the rim lowers the risk of the code becoming unreadable). As such, we determine that Petitioner sufficiently identifies where Yoakim discloses a barcode and explains why one of ordinary skill in the art would have placed such a “barcode” on the bottom of the capsule’s flange.” slip op. at 27

  • PTAB / AIA Trials › Discretionary denial › §325(d) same art / argumentsDecided for petitioner

    “Information Disclosure Statement (IDS) during prosecution of the ’430 patent and that Rossi and Castellani were mentioned in the inter partes reviews that were cited on the IDS. Pet. 19; Prelim. Resp. 23. We need not determine whether Part 1 of the Advanced Bionics framework is satisfied based on these disclosures, however, as Part 2 of the analysis, which we address below, is dispositive. a) Factor (c)—the extent to which the asserted art was evaluated during examination, including whether the prior art was the basis for a rejection The Examiner did not issue any rejections during prosecution of the ’430 patent. Ex. 1002, 232–234. As the reasons for allowance, the Examiner stated: [A]llowance of claims 1 and 21–29 is indicated as none of the cited prior art discloses or suggests the flange comprising a top side and an opposing bottom side; a cover that is fastened to the top side of the flange to close the cavity; and an identifier provided on the bottom side of the flange, the identifier being a barcode, wherein the beverage machine, by reading or detecting the identifier with the sensor/detector, is configured to determine if the single-serve capsule belongs to a group of single serve capsules operable for use with the beverage machine, and only if the beverage machine determines that the single-serve capsule belongs to the group of single serve capsules operable for use with the beverage machine is the pump controlled to push the water into the single-serve capsule. Id. at 233. In arriving at this conclusion, the Examiner did not cite or discuss the disclosures of Yoakim, Jarisch, Rossi, or Castellani. Id. at 232–234. Yet, these references appear, based on the current record, to expressly teach or allowance, including a “flange comprising a top side and an opposing bottom side” (Ex. 1004 ¶ 197, Fig. 6); “a cover that is fastened to the top side of the flange to close the cavity” (Ex. 1004 ¶¶ 128–129, 197, 414); “an identifier provided on the bottom side of the flange” (Ex. 1005 ¶ 22) that is “a barcode” (Ex. 1004 ¶¶ 496, 525); and “reading or detecting the identifier with the sensor/detector . . . to determine if the single-serve capsule belongs to a group of single serve capsules operable for use with the beverage machine” (Ex. 1004 ¶¶ 25, 192, 477, 494–496, 525; Ex. 1005 ¶ 82; Ex. 1041, 3, 11). As such, to the extent the asserted combination of prior art references was evaluated during prosecution of the application that matured into the ’430 patent, we determine that such evaluation was minimal.” slip op. at 37

  • Other 314aDecided for petitioner

    “B. 35 U.S.C. § 314(a) Patent Owner contends that “[t]he parties have been embroiled in disputes involving substantive claims for infringement for both the ’430 Patent and the Jarisch 929 reference,” and “it is unnecessary to open up yet another front in this dispute.” Prelim. Resp. 68–69. As such, Patent Owner requests that we deny institution under 35 U.S.C. § 314(a). Id. Patent Owner directs our attention to no case in which the Director has exercised discretion to deny a petition merely because the same patent was the subject of a co-pending district court infringement action. Indeed, 35 U.S.C. § 315(b) specifically contemplates such a scenario. Accordingly, we decline to exercise discretion to deny the Petition under 35 U.S.C. § 314(a).” slip op. at 40

  § 103 obviousness§ 112 disclosureDiscretionary denial
  Patents in suitUS 11,230,430
• Nespresso USA, Inc. v. K-Fee System GmbHInstituted
  PTAB · Sep 13, 2023 · IPR2023-00502 · APJ Grace Karaffa Obermann · IPR · Institution

  Instituted IPR on claims 1–16 because Petitioner showed a reasonable likelihood that the claims would have been obvious over Yoakim, Jarisch, and Rapparini.

  RulingsInstitution decision

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted

    “review. 35 U.S.C. § 314 (2018); 37 C.F.R. § 42.4(a) (2022). The standard for institution is set forth in 35 U.S.C. § 314(a), which provides that an inter partes review may not be instituted “unless the Director determines . . . there is a reasonable likelihood that the petitioner would prevail with respect to at least [one] of the claims challenged in the petition.” For the reasons set forth below, Petitioner demonstrates a reasonable likelihood of prevailing with respect to claims 1–16 of the ’923 patent. Accordingly, we institute an inter partes review.” slip op. at 2

  • Disclosure Requirements (§112) › Written description (Ariad)Not entitled to earlier dateDecided for petitioner

    “benefit of the filing date of an earlier filed application only if the disclosure of the earlier application provides support for the claims of the later application, as required by 35 U.S.C. § 112.” In re Chu, 66 F.3d 292, 297 (Fed. Cir. 1995). One may show support for the claims of a later application by showing that a single, earlier application provides written description support for the claims. PowerOasis, Inc. v. T-Mobile USA, Inc., 522 F.3d 1299, 1306 (Fed. Cir. 2008); Studiengesellschaft Kohle, MBH v. Shell Oil Co., 112 F.3d 1561, 1564 (Fed. Cir. 1997) (noting that a patentee “cannot distinct previous applications”). Once Petitioner identifies a prior art reference with an effective filing date prior to that of the challenged patent, the burden of production to show entitlement to the benefit of the filing date of an earlier filed application shifts to Patent Owner. See In re NTP, 654 F.3d 1268, 1276 (Fed. Cir. 2011) (“a patent’s claims are not entitled to an earlier priority date merely because the patentee claims priority . . . Rather, for a patent’s claims to be entitled to an earlier priority date, the patentee must demonstrate that the claims meet the requirements of 35 U.S.C. § 120”). Patent Owner may show possession of the invention through “such descriptive means as words, structures, figures, diagrams, formulas, etc., that fully set forth the claimed invention.” Lockwood v. Am. Airlines, Inc., 107 F.3d 1565, 1572 (Fed. Cir. 1997). “Although the exact terms need not be used in haec verba, . . . the specification must contain an equivalent description of the claimed subject matter. A description which renders obvious the invention for which an earlier filing date is sought is not sufficient.” Id.” slip op. at 9

  • Novelty / Anticipation (§102) › Priority / effective filing date / continuation supportReference is prior artPriority date, deniedDecided for petitioner

    “Once Petitioner identifies a prior art reference with an effective filing date prior to that of the challenged patent, the burden of production to show entitlement to the benefit of the filing date of an earlier filed application shifts to Patent Owner. See In re NTP, 654 F.3d 1268, 1276 (Fed. Cir. 2011) (“a patent’s claims are not entitled to an earlier priority date merely because the patentee claims priority . . . Rather, for a patent’s claims to be entitled to an earlier priority date, the patentee must demonstrate that the claims meet the requirements of 35 U.S.C. § 120”). Patent Owner may show possession of the invention through “such descriptive means as words, structures, figures, diagrams, formulas, etc., that fully set forth the claimed invention.” Lockwood v. Am. Airlines, Inc., 107 F.3d 1565, 1572 (Fed. Cir. 1997). “Although the exact terms need not be used in haec verba, . . . the specification must contain an equivalent description of the claimed subject matter. A description which renders obvious the invention for which an earlier filing date is sought is not sufficient.” Id.” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundInstituted

    “7. Analysis: Reasons to Combine the References Petitioner shows sufficiently that Yoakim, Jarisch and Rapparini are “analogous art in the field of portion capsule beverage extraction, each disclosing an invention that may be applied in automatic coffee/espresso machines.” Pet. 43. “Yoakim and Jarisch both improve the optimization of beverage parameters in a single-serve brewing system, and use optical codes read by the machine to achieve this.” Id. “Rapparini further improves the the wall of the capsule body like those used in Yoakim and Jarisch.” Id. at 43–44; see id. at 50–51, 53–54 (Petitioner’s further argument that Rapparini discloses “an optimized capsule structure that is stiffer and more stable” by virtue of radially spaced and vertically oriented ribs and grooves, where the vertically oriented grooves are free from extending entirely to the bottom region of the capsule). Petitioner directs us to additional evidence tending to establish that an ordinarily skilled artisan would have been prompted to modify Yoakim’s device, to include the code placement of Jarisch and the grooves and ribs of Rapparini, to arrive at the claimed invention with an expectation of success. Id. at 44–48.” slip op. at 27

  § 102 anticipation§ 103 obviousness§ 112 disclosureDiscretionary denialcites Phillips
  Patents in suitUS 10,994,923
• Tokyo Ohka Kogyo., Ltd. v. Fujifilm Electronic Materials U.S.A., Inc.All claims unpatentable
  PTAB · May 31, 2023 · PGR2022-00010 · APJ Jo-Anne M Kokoski · PGR · Final written decision

  Claims 1–15 are unpatentable for lack of written description support under § 112(a); the Board did not reach either obviousness ground.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person having ordinary skill in the art (“POSA”) “would have had a Bachelor degree in materials science, engineering, chemistry or similar technical discipline, and had at least two years of experience relating to the design and development of semiconductor manufacturing processes.” Pet. 14. Petitioner further submits that, “[a]lternatively, such a person may have had additional graduate education as a substitute for professional experience, or significant work experience as a substitute for formal education.” Id. Patent Owner states that, “[w]ithout taking a position on the correctness of this definition, Patent Owner applies Petitioner’s POSA definition.” PO Resp. 11 (citing Pet. 14). 3 The Leahy-Smith America Invents Act (“AIA”), Pub. L. No. 112–29, 125 Stat. 284 (2011), revised 35 U.S.C. § 103 effective March 16, 2013. Petitioner contends, and Patent Owner does not contest, that “the earliest priority date claimed by the ’329 patent” is December 6, 2013. Pet. 13; PO Resp. 6. Because the undisputed earliest claimed priority date of the ’329 patent is after March 16, 2013, we apply the AIA versions of §§ 102 and 103. record, and is consistent with the level of skill in the art at the time of the invention as reflected in the prior art in this proceeding.” slip op. at 5

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “We disagree. It is clear from the plain language of claim 1 that the claimed “cleaning composition” is a composition for cleaning that includes four named components and has a specified pH. Ex. 1001, 29:2–9. The ’329 patent specification unambiguously teaches that the cleaning composition is for removing residues from semiconductor substrates. Id. at 1:23–29, 2:10–12, 2:17–33, 15:52–55. Although the ’329 patent describes a cleaning composition that comprises a redox agent, a chelating agent, a metal corrosion inhibitor, an organic solvent, and water, we see no reason to construe the term “cleaning composition” itself to require these components. Claim 1 expressly recites expressly including or precluding a chelating agent or a metal corrosion inhibitor. Ex. 1001, 29:2–9. The Federal Circuit advises that the specification “is not a suitable substitute for, nor can it be used to rewrite, the chosen claim language. ‘Specifications teach. Claims claim.’” SuperGuide, 358 F.3d at 875 (quoting SRI Int’l v. Matsushita Elec. Corp. of Am., 775 F.2d 1107, 1121 n. 14 (Fed. Cir. 1985) (en banc)). The ’329 patent specification does teach a cleaning composition that includes a redox agent, a chelating agent, a metal corrosion inhibitor, an organic solvent, and water, but claim 1 is directed to a cleaning composition that expressly requires only a subset of those components. Patent Owner’s proposed construction would effectively rewrite the claim by adding unclaimed components, which we decline to do under the guise of claim construction. See id. (“Though understanding the claim language may be aided by the explanations contained in the written description, it is important not to import into a claim limitations that are not a part of the claim.”).” slip op. at 9

  • Disclosure Requirements (§112) › Written description (Ariad)Written description inadequateUnpatentable

    “that Petitioner establishes that the ’329 patent does not provide sufficient written description support for the challenged claims. Pet. 15–43; Ex. 1007 ¶¶ 56–82. More specifically, we find that the ’329 patent does not reasonably convey to a POSA that the inventor was in possession of cleaning compositions that do not include a chelating agent or a metal corrosion inhibitor. There is no dispute, on this record, that the ’329 patent specification explicitly teaches that a redox agent, a chelating agent, a metal corrosion inhibitor, an organic solvent, and water are mandatory components of the cleaning composition described therein. PO Resp. 15 (Patent Owner agreeing with Petitioner that “[t]he ’329 patent’s disclosure is unambiguously explicit regarding mandatory components of the cleaning compositions described therein.” (citing Pet. 17; Ex. 1007 ¶¶ 56–57) (emphasis omitted, alteration in original)); see Ex. 1001, 3:47–48, 3:62–64, 10:24–26, 10:66–11:2, 12:3–4; Ex. 1007 ¶¶ 56–67. Claim 1, however, does not require that the cleaning composition include a chelating agent or a metal corrosion inhibitor. Ex. 1001, 29:2–9. Therefore, establishing proper written description support for claim 1 requires more than showing that the inventor was in possession of a cleaning composition that includes a redox agent, a chelating agent, a metal corrosion inhibitor, an organic solvent, and water; the ’329 patent must also show that the inventor was in possession of a cleaning composition that includes only a redox agent (hydroxylamine), an organic solvent (an alkylene glycol), water, and an alkanolamine. Id.” slip op. at 13

  Patent outcomesUS 10,927,329 unpatentable
  Claim construction§ 112 disclosurecites Phillips
  Patents in suitUS 10,927,329

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.