PTAB
Advanced fields
170 decisions · 416msnewest first
  • PTAB · Oct 6, 2026 · IPR2025-00706 · APJ Eric C Jeschke · IPR · Final written decision

    Claims 1, 4, and 7–10 are unpatentable as obvious over Goubet and anticipated by Gao; proposed substitute claims 20 and 21 are denied as indefinite and lacking written-description support.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “In the Response, Patent Owner states that it “does not dispute” the definition of one of ordinary skill in the art proposed by Petitioner, but Patent Owner “reserves the right to address [the definition] should new issues materialize.” PO Resp. 6. Patent Owner did not address this issue in the Sur-reply. As noted in the Decision on Institution, Petitioner’s proposed definition appears generally consistent with the record, including the prior art. See Dec. Inst. 8 (citing In re GPAC Inc., 57 F.3d at 1579). We remove the phrase “at least” in both listed options, however, as that phrase adds ambiguity. Further, Patent Owner has not argued at trial that Petitioner’s proposal for the level of ordinary skill leads to an improper understanding of how a skilled artisan would have understood either the challenged patent or the prior art. In the analysis below, we continue to apply the level of ordinary skill in the art adopted in the Decision on Institution, as proposed by Petitioner.” slip op. at 9

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed petitioner constructionOther

      “Network LLC, 929 F.3d 1350, 1357 (Fed. Cir. 2019). At first glance, the language of the limitation at issue—which, again, recites “the compressed air and the operative fluid mix together in said mixing chamber to form the fluid dispersion”—would seem to require the “fluid dispersion” (under the stipulated construction) to be fully formed in the “mixing chamber.” In other words, the language of the limitation alone would seem to support Patent Owner’s proposed construction for the “form the fluid dispersion” limitation. But the claim construction analysis does not end with consideration of the claim language alone. Next, we turn to the Specification. The Federal Circuit has said that the specification “is the single best guide to the meaning of a disputed term.” Phillips, 415 F.3d at 1315 (quoting Vitronics Corp. v. Conceptronic, Inc., 90 F.3d 1576, 1582 (Fed. Cir. 1996)). Here, the discussion in the Specification of precisely the same language as in the limitation at issue strongly supports that “to form a fluid dispersion” in the limitation at issue requires only initial mixing of the compressed air and operative fluid in the mixing chamber, with further “formation” of the ”fluid dispersion” occurring downstream of the mixing chamber: More importantly, the “predetermined amount” of compressed air and the “preselected amount” of the operable fluid are initially mixed together in the mixing chamber 226 to form a fluid dispersion. The diffusion chamber 112" is further structured to facilitate the formation of a plurality of substantially uniform droplets, as defined hereinabove, in the fluid dispersion prior to discharge from the diffusion chamber 112" through discharge port 132. Ex. 1001, 10:62–11:2 (emphasis added) (discussing Figure 6), quoted, in part, at Pet. Reply 6–710; see also Ex. 1001, 5:64–6:4 (same language, except without double primes, in a discussion of Figures 1 and 2). To be sure, certain passages in the Specification could be read to indicate that a “fluid dispersion” must be fully formed in the “mixing chamber.” See, e.g., Ex. 1001, 6:11–12 (“More in particular, the suppression chamber 232 receives the fluid dispersion from the mixing chamber 226.”); see also id. at 7:22–33, 11:39–52 (both implying that a “fluid dispersion” is formed in the mixing chamber). But the passage block quoted directly above (and the similar one bridging columns 5 and 6) more directly addresses the issue at hand—i.e., the scope of “form the fluid dispersion”—by using the same” slip op. at 13

    • Expert testimonyPatent owner expert discountedMixed

      “As an initial matter, the record here does not support any sound basis to disregard the entirety of Dr. Micklow’s Declaration for allegedly not reviewing the parties’ claim constructions. See Pet. Reply 2 (citing Ex. 1046, 115:15–18). Contrary to Petitioner’s argument, in the cited discussion, Dr. Micklow does not indicate that he applied an incorrect understanding of a claim term. Cf. Cordis Corp. v. Bos. Sci. Corp., 658 F.3d 1347, 1357–58 (Fed. Cir. 2011) (disregarding testimony “based on an incorrect understanding of the claim construction”), cited at Pet. Reply 1. Instead, we read Dr. Micklow’s testimony as clarifying that he was not involved in claim construction at all and that, as stated, he “made [his] opinions based on what [he] read in the patents.” Ex. 1046, 112:11–12; see also id. at 115:15–18 (“I don’t know if I would even apply claim construction. I applied engineering principles to a document that had been published with the patent office.”).” slip op. at 18

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable

      “To satisfy its burden of proving obviousness, a petitioner cannot employ mere conclusory statements. The petitioner must instead articulate specific reasoning, based on evidence of record, to support the legal conclusion of obviousness.” In re Magnum Oil Tools Int’l, Ltd., 829 F.3d 1364, 1380 (Fed. Cir. 2016); TriVascular, Inc. v. Samuels, 812 F.3d 1056, 1066 (Fed. Cir. 2016) (“Although the KSR test is flexible, the Board ‘must still be careful not to allow hindsight reconstruction of references . . . without any explanation as to how or why the references would be combined to produce the claimed invention.’”) (citation omitted). Based on the complete record, we agree with Patent Owner that “Petitioner’s asserted motivation boils down to the conclusory statement that given Goubet and Kaiser, ‘it was well known in the field at the time of the invention that droplets of greater uniformity result in uniform droplet evaporation.’” PO Resp. 31 (quoting Pet. 59). We agree with Patent Owner that Petitioner’s discussion of the alleged reasons to combine (Pet. 59) is insufficient to support the proposed combination here. See Magnum Oil, 829 F.3d at 1380. Specifically, we are not persuaded that Kaiser’s teachings—which relate to combustion (Ex. 1014 at 43)—would have led one of ordinary skill in the art to the proposed modifications, which would allegedly “improve the smoothness (i.e., less harsh) of the aroma generated as the oil droplets evaporate in the surrounding airspace.” See Pet. 59 (emphasis added); White Pet. Decl. ¶ 251 (same); see PO Resp. 32 (“Rather, Dr. White merely describes the ability to achieve the effect as in the claimed patent, not why a [person of ordinary skill in the art] would look to the field of electrospray injection and combustion in mesoscale power-generation systems, using high-voltage electric fields to generate charged fuel droplets for controlled combustion in catalytic micro-combustors when considering atomization for scents.”). For these reasons, we determine, in light of the complete record, that Petitioner has not shown by a preponderance of the evidence that one of ordinary skill in the art at the time of the invention would have had reason to combine Goubet and Kaiser, as proposed. slip op. at 32

    Patent outcomesUS 10,583,449 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · Nautilus
    Patents in suitUS 10,583,449
  • PTAB · Oct 6, 2026 · IPR2025-00705 · APJ Eric C Jeschke · IPR · Final written decision

    Claims 7–9 and 11 are unpatentable as obvious over Goubet; proposed substitute claim 21 is denied as indefinite.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “In the Response, Patent Owner states that it “does not dispute” the definition of one of ordinary skill in the art proposed by Petitioner, but Patent Owner “reserves the right to address [the definition] should new issues materialize.” PO Resp. 5. Patent Owner did not address this issue in the Sur-reply. As noted in the Decision on Institution, Petitioner’s proposed definition appears generally consistent with the record, including the prior art. See Dec. Inst. 8 (citing In re GPAC Inc., 57 F.3d at 1579). We remove the phrase “at least” in both listed options, however, as that phrase adds ambiguity. Further, Patent Owner has not argued at trial that Petitioner’s proposal for the level of ordinary skill leads to an improper understanding of how a skilled artisan would have understood either the challenged patent or the prior art. In the analysis below, we continue to apply the level of ordinary skill in the art adopted in the Decision on Institution, as proposed by Petitioner.” slip op. at 9

    • Expert testimonyPetitioner expert creditedDecided for patent owner

      “The record here does not support any sound basis to disregard the entirety of Dr. Micklow’s Declaration, as asserted in Petitioner’s overall argument. See Pet. Reply 1–2. Contrary to Petitioner’s argument, in the cited general discussion, Dr. Micklow does not indicate that he applied an incorrect understanding of a claim term. Cf. Cordis Corp. v. Bos. Sci. Corp., 658 F.3d 1347, 1357–58 (Fed. Cir. 2011) (disregarding testimony “based on an incorrect understanding of the claim construction”), cited at Pet. Reply 1; see also Pet. Reply 2 (arguing that “Dr. Micklow’s declaration is premised on understandings of claim scope that are inconsistent with the constructions advanced by both of the parties” (emphasis added)). Instead, we read the cited portions of Dr. Micklow’s testimony as clarifying that he was not involved in claim construction at all and that, as stated, he “made [his] opinions based on what [he] read in the patents.” Ex. 1046, 112:11–12; see also Pet. Reply 1 (citing Ex. 1046, 112:4–12, 113:13–20, 115:15–18). Next, we turn to each of the four specific claim terms that Petitioner highlights in its further arguments.” slip op. at 12

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction needed

      “B. Claim Construction In inter partes reviews, the Board interprets claim language using the same claim construction standard that would be used in a civil action under 35 U.S.C. § 282(b), as described in Phillips v. AWH Corp., 415 F.3d 1303 (Fed. Cir. 2005) (en banc). See 37 C.F.R. § 42.100(b). Under that standard, we generally give claim terms their ordinary and customary meaning, as would be understood by a person of ordinary skill in the art at the time of the invention, in light of the language of the claims, the specification, and the prosecution history. See Phillips, 415 F.3d at 1313–14. Although extrinsic evidence, when available, may also be useful when construing claim terms under this standard, extrinsic evidence should be considered in the context of the intrinsic evidence. See id. at 1317–19. Neither Petitioner nor Patent Owner propose explicit constructions for any claim terms. Pet. 10–11; PO Resp. 5. Based on the complete record, we need not construe explicitly any claim terms because doing so would not change the outcome of the analysis below. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 9

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for patent owner

      “Florida Litigation a Joint Claim Construction statement that included stipulated claim constructions and disputed claim constructions for terms in the challenged patent as well as the ’449 patent and the ’918 patent. See Ex. 1018, Exhibit A (Stipulated Claim Constructions), Exhibit B (Disputed Claim Constructions). The parties stipulated to the construction of the terms “fluid dispersion” and “baffle” as recited in the challenged claim. See id., Exhibit A.10 10 When staying the Florida Litigation, the District Court cancelled the scheduled claim construction hearing. See ECF No. 67 (April 8, 2025) (granting joint motion to stay); ECF No. 68 (April 8, 2025) (cancelling the The stipulated construction of “fluid dispersion” merely restates the express definition of “fluid dispersion” from the challenged patent (although the definition is not cited or discussed in the parties’ filing). Compare Ex. 1018, Exhibit A, with Ex. 1001, 3:8–20. Similarly, the stipulated construction of “baffle” essentially parrots one sentence in the challenged patent (again, not cited or discussed in the parties’ filing). Compare Ex. 1018, Exhibit A, with Ex. 1001, 7:57–59. To the extent necessary, we determine that the complete record supports the parties’ stipulated constructions of “fluid dispersion” and “baffle,” and we apply those constructions below.” slip op. at 10

    Patent outcomesUS 9,527,094 unpatentable
    Claim construction§ 103 obviousness§ 112 disclosurecites Phillips · Nautilus
    Patents in suitUS 9,527,094
  • PTAB · Sep 29, 2026 · IPR2025-01122 · APJ Carl M Defranco · IPR · Final written decision

    Claims 1–16 are unpatentable as obvious over Liao or Liao and Cheng; Rolicki is not prior art, and the challenge over Offord ’341 and Offord ’797 fails.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “A. Level of Ordinary Skill in the Art Baby Jogger does not dispute Evenflo’s definition of the level of ordinary skill in the art, which is that a person of ordinary skill in the art (hereinafter, “one skilled in the art”) would have had “a bachelor’s degree in a relevant field (e.g., mechanical engineering or industrial design) and at least two years of product design experience and/or industry experience with juvenile products” and that “[m]ore education can replace product design experience, and vice versa.” Pet 8 (citing Ex. 1001 ¶¶ 31–33); PO Resp. generally. We apply that definition here, as it accords with the problems addressed in the prior art and the specification of the ’682 patent.” slip op. at 7

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

      “At the outset, we note that the claim language requires only that “the first seat and the second seat” be arranged in an inline descending configuration, not that the seat’s mounting points or other physical connections be so arranged. Ex. 1010, 17:31–33. Baby Jogger improperly reads “seats” out of the claim and substitutes the seat’s “mounting points” on the frame. A proper reading of the claim language focuses on what happens when both seats are connected to the frame, not where they are so connected. In other words, “when connected to the frame” simply emphasizes that both seats must be connected to the frame to form the inline descending configuration, as opposed to the single stroller embodiment of Figure 1, where there cannot be an inline descending configuration because only one seat is connected to the frame and the other seat is removed, i.e., not connected to the frame. That reading is supported by the specification of the ’682 patent,” slip op. at 9

    • Novelty / Anticipation (§102) › Priority / effective filing date / continuation supportPriority date awardedDecided for patent owner

      “We find that testimony persuasive, for it shows what one skilled in the art would have recognized the 2008 Provisional as necessarily disclosing. The relevant inquiry is whether the disclosure of the prior application “convey[s] with reasonable clarity to those skilled in the art that, as of the filing date sought, the inventor was in possession of the invention.” PowerOasis, 522 F.3d at 1306 (emphasis in original; citation omitted). “While a prior application need not contain precisely the same words as are found in the asserted claims, . . . the prior application must indicate to a person skilled in the art that the inventor was ‘in possession’ of the invention as later claimed.” Id. In other words, “to satisfy the written description requirement, ‘the missing descriptive matter must necessarily be present in the [original] application’s specification such that one skilled in the art would recognize such a disclosure.’”7 Id. (quoting Tronzo v. Biomet, Inc., 156 F.3d 1154, 1159 (Fed. Cir. 1998) (emphasis added). “This requires that the written description actually or inherently disclose the claim element.” Id. at 1306–07. Moreover, a drawing may supply written description for the arrangement it depicts even though the text describes that arrangement in different terms. See Cooper Cameron Corp. v. Kvaerner Oilfield Prods., Inc., 291 F.3d 1317, 1319–23 (Fed. Cir. 2002).” slip op. at 16

    • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable

      “Instead, Evenflo’s argument rests on isolating the statement—“A similar sub-frame arrangement is disclosed in [Offord ’797]”—from the remainder of the passage in which that statement appears in order to arrive at a reason to incorporate the reversibility teaching of Offord ’797. However, when that statement is read in the context of the full passage in which it appears, nowhere does that passage suggest reversibility as the reason for referencing Offord ’797. More accurately, it suggests a different reason that relates to a curved lug 108 by which sub-frame 100 rests on the stroller’s main frame 4 to carry the weight of the stroller’s two occupants— When the interface components 100 are attached to the frame assembly 4 they form a sub-frame of the frame assembly 4, and when the child-carrying units are mounted thereon, one behind the other, they are in a compact echelon formation, one of the connector sockets 106 of each component 100 being at a higher level in relation to the ground than the other connector sockets 106. The higher connector socket 106 and further connecting leg 102 are both connected to the respective opposite ends of an upper mounting piece 107. In addition, on the inner side of the lower connector sockets 106 there is a downwardly curved lug 108 which serves to rest upon a part of the basket frame 44, such that the weight of two infants is fully supported by the frame assembly 4. A similar sub-frame arrangement is disclosed in [Offord ’797]. Ex. 1051, 9:23–36 (emphasis added). That passage shows that, rather than reversibility of the sub-frame, the reference to Offord ’797 is more aptly directing the reader to the arrangement and details of a similarly curved lug structure in the stroller sub-frame of Offord ’797. Indeed, Figures 5 and 6 of Offord ’797, reproduced below, disclose just such a curved lug in the context of “corner pieces 20” having “channel 21.” Ex. 1054, 4:10–23.” slip op. at 53

    Patent outcomesUS 11,731,682 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousness
    Patents in suitUS 11,731,682
  • PTAB · Sep 23, 2026 · IPR2025-00878 · APJ Carl M Defranco · IPR · Final written decision

    Claims 1–3 and 11 are unpatentable as anticipated by Cleveland and obvious over Nakagawa and over Nakagawa combined with Tanner.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “would have at least a bachelor’s degree in mechanical or chemical engineering, materials science, polymer science, or equivalent coursework, at least a year of experience developing paper-based laminates involving the application of polymer coatings to a substrate, and the appropriate industry familiarity with biodegradability standards and degradability techniques [and] . . . [l]ess work experience may be compensated by a higher level of education, such as a master’s degree, and vice versa. Pet. 16 (citing Ex. 1003 ¶ 50). Clearwater’s definition is uncontested, and we apply that definition here, as it accords with the level of skill reflected in the asserted prior art and the problems addressed in the specification of the ’126 patent. C. Claim Construction” slip op. at 6

    • Expert testimonyPetitioner expert creditedDecided for petitioner

      “We have reviewed the cited testimony of Clearwater’s expert, including their calculations for arriving at a coat weight in Nakagawa that falls within the claimed range. See Ex. 1003 ¶¶ 132–33. We find that testimony, which is unrebutted, both credible and supported by the evidence of record. Thus, in light of Clearwater’s contentions, the cited portions of Nakagawa, and the unrebutted testimony of Clearwater’s expert, we are persuaded that Nakagawa discloses or otherwise suggests each and every element of claim 1. See Pet. 45–54, 60–64. Clearwater also persuades us that Cleveland discloses the additional subject matter of dependent claims 2, 3, and 11. See Pet. 64–66. Thus, we determine that Clearwater demonstrates that claims 1–3 and 11 are unpatentable as obvious over Nakagawa. F. Ground 3—Obviousness Over Nakagawa and Tanner” slip op. at 17

    • Novelty / Anticipation (§102) › Prior-art status of a reference › Patents / published applications (effective date, provisional support)Reference is prior artDecided for petitioner

      “qualifies as prior art under 35 U.S.C. § 102(e)(1) “based on both its provisional and non-provisional filing dates.” Inst. Dec. 4 n.5. We were persuaded by Clearwater’s proof that Cleveland’s provisional (Ex. 1006) is “virtually identical” to Cleveland itself (Ex. 1005) and that the provisional provides written description support for at least claim 1 of Cleveland. See Pet. 18–21 (citing Ex. 1006, 2–6, 9). We were also persuaded by Clearwater’s showing that the provisional provides written support for the subject matter relied upon in Cleveland. Id. at 21–40 (citing Ex. 1006, 1–9). We are still persuaded by Clearwater’s showing. Thus, we see no reason to disturb our earlier finding that Cleveland is prior art to the ’126 patent.” slip op. at 7

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

      “protectant layers has “a coat weight of from 5 to 30 lbs/3000 ft2.” As noted by Clearwater, Cleveland discloses a total coat weight for layers 14 and 16 as falling within the claimed range. Pet. 32–34 (citing Ex. 1005 ¶ 32). In particular, Cleveland discloses that “the coextruded layer of copolyester (irrespective of which side of the substrate the layer is disposed) is of a total coat weight of between about 10 and about 40 lb/3000 ft2 in any combination of between about 80/20 to 20/80 parts by weight of Ecoflex to Biomax,” of which “a total coat weight of 25 lb/3000 ft2 is preferred.” Ex. 1005 ¶ 32. As disclosed, Cleveland’s total coat weight range of 10–40 lb/3000 ft2 falls almost entirely within the claimed range, and the preferred total coat weight of 25 lb/3000 ft2 falls squarely within the claimed range. Thus, Cleveland satisfies claim elements [1.3.2] and [1.5.2]. See Titanium Metals Corp. v. Banner, 778 F.2d 775, 782 (Fed. Cir. 1985) (“[W]hen, as by a recitation of ranges or otherwise, a claim covers several compositions, the claim is anticipated if one of them is in the prior art.”) (citation omitted). As such, we find that Clearwater adequately demonstrates that Cleveland discloses all the elements of claim 1. 4. Dependent Claims” slip op. at 12

    Patent outcomesUS 8,637,126 unpatentable
    § 102 anticipation§ 103 obviousnesscites Phillips
    Patents in suitUS 8,637,126
  • PTAB · Nov 10, 2025 · IPR2025-00878 · APJ Carl M Defranco · IPR · Institution

    The Board instituted review of claims 1–3 and 11 after finding a reasonable likelihood that claim 1 is anticipated by Cleveland or obvious over Nakagawa.

    RulingsInstitution decision
    • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted

      “contentions, the cited portions of Cleveland, and the testimony of Clearwater’s expert), we find, preliminarily, that Cleveland discloses each claim element in the manner recited by claim 1. Thus, on the current record, Clearwater demonstrates a reasonable likelihood that challenged claim 1 is unpatentable as anticipated by Cleveland.” slip op. at 6

    • Novelty / Anticipation (§102) › Prior-art status of a reference › Patents / published applications (effective date, provisional support)Reference is prior artDecided for petitioner

      “5 Clearwater argues that Cleveland qualifies as prior art under 35 U.S.C. § 102(e)(1) “based on both its provisional and non-provisional filing dates.” Pet. 17. In support, Clearwater asserts that Cleveland’s provisional (Ex. 1006) is “virtually identical” to Cleveland itself (id. at 18) and submits claim charts to demonstrate that the Cleveland provisional provides written support for: (1) at least claim 1 of Cleveland (id. at 18–21); and (2) the subject matter relied upon in Cleveland (id. at 21–40 (citing Ex. 1006 throughout)). Based on our review of the Cleveland provisional, as well as Clearwater’s claim charts, we are persuaded that the current record demonstrates that Cleveland is prior art to the challenged patent. See Dynamic Drinkware, LLC v. Nat’l Graphics, Inc., 800 F.3d 1375, 1381 (Fed. Cir. 2015).” slip op. at 4

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Instituted

      “satisfies each claim element as identified above in Section I.D, i.e., elements [1.pre]–[1.6]. See id. at 22–40. Clearwater also submits annotated Figure 3 of Cleveland, reproduced below, to further illustrate the specific laminate structure of Cleveland’s coffee cup. See id. at 39.” slip op. at 5

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successInstituted

      “protective layers have “a coat weight of from 5 to 30 lbs/3000 ft2,” Clearwater submits the declaration of its expert, who explains that, because Nakagawa identifies the specific polymers and the thickness of the coat used for the plastic layers and one skilled in the art “would recognize that the disclosed polymers have a given density,” then “[w]ith these known parameters, the coat weight is easily calculated to be 23.04 lbs./ 3000 ft2 — falling squarely within the claimed range.” Pet. 53–54 (citing Ex. 1003 ¶¶ 132–133; Ex. 1008 ¶ 24; Ex. 1024, at 4). At this stage, we find that testimony credible and supported by the evidence presently of record. After reviewing the preliminary record (including Clearwater’s contentions, the cited portions of Nakagawa, and the testimony of Clearwater’s expert), we find, preliminarily, that Nakagawa discloses or otherwise suggests each claim element in the manner recited by claim 1. Thus, on the current record, Clearwater demonstrates a reasonable likelihood that challenged claim 1 is unpatentable as obvious over Nakagawa. We need not decide Clearwater’s challenge of the dependent claims based on Nakagawa alone nor its challenge of claims 1–3 based on Nakagawa and Tanner. Our analysis of these challenges, in our view, is best left for trial after full development of the record.” slip op. at 8

    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips
    Patents in suitUS 8,637,126
  • PTAB · Oct 28, 2025 · IPR2024-00858 · APJ Carl M Defranco · IPR · Final written decision

    Claims 5–7 and 16–19 were not shown unpatentable under § 102 or § 103 because the cited references failed to disclose the claimed closure retention mechanism.

    RulingsFinal written decision
    • Claim Construction › Functional claiming / §112(f) means-plus-function › Whether §112(f) applies (Williamson, nonce words)§112(f) appliesPrior construction adoptedDecided for petitioner

      “1. “closure retention mechanism” Trove proposes that “closure retention mechanism” should be construed as a means-plus-function term under 35 U.S.C. § 112(f). See Pet. 18–19; Pet. Reply 1. CamelBak agrees. See PO Resp. 8. Indeed, subsequent to our institution decision, the district court in the parallel action held that the “closure retention mechanism” is a means-plus-function term governed by 35 U.S.C. § 112(f). See Ex. 2010, at 5–6. We see no reason to depart from that holding and adopt the district court’s reasoning in that regard as our own. See id. at 6–8.” slip op. at 7

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

      “We agree with CamelBak that the plain language of the claim imposes a temporal condition on when the closure is received by the closure retention mechanism, namely, only after it is removed from the drink spout. In other words, the closure cannot be in engagement with, i.e., “received by,” the closure retention mechanism while it remains on the drink spout. This interpretation is consistent with the specification, which repeatedly states that spaced-apart tabs 56 “engage” the closure when it is removed from the spout and moved to the stowed position. Ex. 1001, 8:58–60 (“tabs 56 . . . are configured to selectively engage and retain, or otherwise grip, the closure in the stowed position”); 9:32–39 (“when the closure is positioned between and/or otherwise in engagement with the tabs, the tabs engage the closure across the maximum width, such as with the tabs resiliently deflecting, bending, or compressing to accommodate the greater width of the closure”); 11:36–39 (“the closure retention mechanism 54 may be configured to engage . . . the closure to operatively retain the closure in its stowed configuration.”); 13:26–31 (“When the closure is operatively positioned within the closed perimeter of the handle into its stowed position . . . such closure is compressed slightly.”) (emphases added). Moreover, the specification describes this engagement as occurring by means of a “friction-fit” or “snap-fit” arrangement (id. at 8:50–52, 14:33– 36), which confirms that the closure is not permanently engaged with the tabs, but rather moved into engagement with the tabs, i.e., “received by the closure retention mechanism” per the plain language of the claim. Thus, the intrinsic evidence—the claim language and the specification—supports a construction that imposes a temporal condition on the recited function of the claimed “closure retention mechanism” such that it receives the closure only after the closure has been removed from the drink spout, meaning the closure is not engaged with the closure retention mechanism before it is selectively removed from the drink spout.” slip op. at 13

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

      “3. “retain the closure in a stowed position” CamelBak contends that this limitation should be construed to mean “to hold or keep the closure in a position removed from the drink spout.” PO Resp. 13–14; PO Sur-Reply 4. Although Trove contends that CamelBak’s construction “impermissibly rewrites” the claim language, Trove nonetheless “does not disagree that it encompasses ‘hold or keep the Indeed, the claim language itself already contemplates just such a construction by expressly reciting that the closure retention mechanism “selectively retain[s] the closure in a stowed position relative to the handle when the closure is selectively removed from the drink spout.” Ex. 1001, 18:63–66 (emphasis added). As such, we determine that further construction of this limitation is not necessary to resolve the present dispute.” slip op. at 14

    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Trove proposes that one of ordinary skill in the art would have had— an undergraduate degree in mechanical engineering or equivalent coursework, and a year or more of experience in designing, prototyping, and/or manufacturing fluid containers or similar products . . . [and that] [m]ore work experience may substitute for a lower level of education, and vice versa. Pet. 17–18 (citing Ex. 1003 ¶¶ 25–30). 2 US 9,272,822 B2, issued Mar. 1, 2016 (Ex. 1004, “Samartgis”). 3 EP 2 177 447 A1, published Apr. 21, 2010 (Ex. 1011, “Gorskey”). 4 US 2006/0006578 A1, published Jan. 12, 2006 (Ex. 1012, “Johnson”). 5 US 7,753,240 B2, issued July 13, 2010 (Ex. 1005, “Leoncavallo”). 6 US D586,184 S, issued Feb. 10, 2009 (Ex. 1006, “Miller”). A person having ordinary skill in the art would have had a bachelor’s degree in mechanical engineering or the equivalent coursework and approximately one year of experience with liquid-containing devices, with more work experience substituting for less education and vice versa. See PO Resp. 7 (citing Ex. 2009 ¶¶ 61–68). Because CamelBak simply paraphrases Trove’s slightly more detailed definition of the level of skill in the art, we adopt Trove’s definition, as it appears reasonable and consistent with the asserted prior art and the ’252 patent.” slip op. at 6

    Patent outcomesUS 8,905,252 not shown unpatentable
    Claim construction§ 102 anticipation§ 103 obviousness
    Patents in suitUS 8,905,252
  • PTAB · Oct 10, 2025 · IPR2025-00653 · APJ Bart A Gerstenblith · IPR · Institution

    The Board denied institution on all claims because the Petition did not show a reasonable likelihood that any challenged claim was unpatentable over the asserted grounds.

    RulingsInstitution decision
    • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied

      “An inter partes review may be instituted only if “the information presented in the petition . . . and any [preliminary] response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a) (2024). For the reasons given below, on this record Petitioner has not established a reasonable likelihood that it would prevail in showing the unpatentability of any of the Challenged Claims. Accordingly, we do not institute an inter partes review.” slip op. at 2

    • Skill levelSkill level patent owner adoptedDecided for patent owner

      “The parties’ proposed levels of ordinary skill in the art are similar, although Patent Owner proposes two years of experience along with a bachelor’s degree whereas Petitioner proposes “significant” experience. Patent Owner also proposes an alternative with more extensive experience in lieu of a bachelor’s degree. Although we find Petitioner’s proposed qualifications acceptable, we adopt Patent Owner’s proposed qualifications for the purposes of this Decision because they offer a wider range of qualifications that nonetheless comport with the level of ordinary skill necessary to understand and implement the teachings of the ’504 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001); In re GPAC Inc., 57 F.3d 1573, 1579 (Fed. Cir. 1995); In re Oelrich, 579 F.2d 86, 91 (CCPA 1978). Our analysis and findings herein, however, do not turn on any differences in the parties’ proposed qualifications.” slip op. at 12

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

      “Additionally, only terms that are in controversy need to be construed, and these need be construed only to the extent necessary to resolve the controversy. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). The parties assert that each claim term should be construed in accordance with its plain and ordinary meaning. Pet. 9; Prelim. Resp. 4 (citing Ex. 2009 ¶ 72); see Ex. 1002 ¶ 22 (opining the same). And, in the respective claim construction sections of their briefs, the parties do not propose any claim terms for express construction. We agree with the parties that no claim terms require express construction to resolve the controversy before us. See Realtime Data, 912 F.3d at 1375.” slip op. at 13

    • Expert testimonyPetitioner expert discountedDecided for patent owner

      “Ex. 1002 ¶ 47. As reflected above, Dr. Wooley’s testimony as to element [1.2] does not even assert that Cardamone discloses a tank, let alone one or more sensors disposed at a tank as recited in element [1.2]. Thus, Dr. Wooley’s testimony does not support Petitioner’s argument on this issue.” slip op. at 18

    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 11,726,504
  • PTAB · Oct 10, 2025 · IPR2025-00652 · APJ Bart A Gerstenblith · IPR · Institution

    The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–23 and 25–30 were unpatentable over the asserted grounds.

    RulingsInstitution decision
    • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsDenied

      “presented in the petition . . . and any [preliminary] response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a) (2024). For the reasons given below, on this record Petitioner has not established a reasonable likelihood that it would prevail in showing the unpatentability of any of the Challenged Claims. Accordingly, we do not institute an inter partes review.” slip op. at 2

    • Skill levelSkill level patent owner adoptedDecided for patent owner

      “The parties’ proposed levels of ordinary skill in the art are similar, although Patent Owner proposes two years of experience along with a bachelor’s degree whereas Petitioner proposes “significant” experience. Patent Owner also proposes an alternative with more extensive experience in lieu of a bachelor’s degree. Although we find Petitioner’s proposed qualifications acceptable, we adopt Patent Owner’s proposed qualifications for the purposes of this Decision because they offer a wider range of qualifications that nonetheless comport with the level of ordinary skill necessary to understand and implement the teachings of the ’403 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001); In re GPAC Inc., 57 F.3d 1573, 1579 (Fed. Cir. 1995); In re Oelrich, 579 F.2d 86, 91 (CCPA 1978). Our analysis and findings herein, however, do not turn on any differences in the parties’ proposed qualifications.” slip op. at 12

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

      “The parties assert that each claim term should be construed in accordance with its plain and ordinary meaning. Pet. 10; Prelim. Resp. 4 (citing Ex. 2009 ¶ 73); see Ex. 1002 ¶ 22 (opining the same). And, in the respective claim construction sections of their briefs, the parties do not propose any claim terms for express construction. We agree with the parties that no claim terms require express construction to resolve the controversy before us. See Realtime Data, 912 F.3d at 1375.” slip op. at 13

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

      “We agree with Patent Owner that the Petition fails to demonstrate that Kahn discloses element [1.2] because the evidence cited does not disclose a “first computer system being configured to provide remote control of the first pump or first valve” (i.e., a fluid-handling device). Kahn is directed to providing access to fluid sensing data and analyzing and providing visual information on that data, but Petitioner has not identified any disclosure of the capability to remotely control fluid-handling devices. See, e.g., Ex. 1005, code (54), 1:27–36, 2:50–3:2. More specifically, Kahn’s disclosures that Petitioner relies on for allegedly teaching remote control are deficient. We discuss each. First, Petitioner points to the following, “[f]or instance, as illustrated in FIG. 1C, a fluid control device such as a valve 15A is located on the input side of a sen[s]or unit 110.” Ex. 1005, 8:19–21, cited in Pet. 13. This portion of Kahn, however, does not disclose remote control. Second, Petitioner cites to the following: Finally, or in addition to, the communication unit 112B can include on-site alerts such as optical (indicator lights), audible alerts (e.g., alarm sounds), tactile (e.g., vibration of the unit) or can be interfaced to an appropriate control valve for simply shutting off the supply of fluid upon the detection of emergency events, for instance. Pet. 13 (citing Ex. 1005, 10:62–67). We agree with Patent Owner that this portion of Kahn teaches on-site alerts and local control of the fluid-handling device. See Prelim. Resp. 7. This portion of Kahn does not disclose remote control.” slip op. at 18

    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 11,294,403
  • PTAB · Oct 10, 2025 · IPR2025-00651 · APJ Bart A Gerstenblith · IPR · Institution

    The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–3, 6, 7, and 9–20 were unpatentable over any asserted ground.

    RulingsInstitution decision
    • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsDenied

      “presented in the petition . . . and any [preliminary] response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a) (2024). For the reasons given below, on this record Petitioner has not established a reasonable likelihood that it would prevail in showing the unpatentability of any of the Challenged Claims. Accordingly, we do not institute an inter partes review.” slip op. at 2

    • Skill levelSkill level patent owner adoptedDecided for patent owner

      “The parties’ proposed levels of ordinary skill in the art are similar, although Patent Owner proposes two years of experience along with a bachelor’s degree whereas Petitioner proposes “significant” experience. Patent Owner also proposes an alternative with more extensive experience in lieu of a bachelor’s degree. Although we find Petitioner’s proposed qualifications acceptable, we adopt Patent Owner’s proposed qualifications for the purposes of this Decision because they offer a wider range of qualifications that nonetheless comport with the level of ordinary skill necessary to understand and implement the teachings of the ’680 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001); In re GPAC Inc., 57 F.3d 1573, 1579 (Fed. Cir. 1995); In re Oelrich, 579 F.2d 86, 91 (CCPA 1978). Our analysis and findings herein, however, do not turn on any differences in the parties’ proposed qualifications.” slip op. at 11

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

      “target value” is part of a command that is sent from a computing device to a server and then to a controller. The controller then receives a measurement of the fluid by a sensor and determines whether the measurement satisfies the “target value.” If the measurement does not satisfy the “target value,” further operations are undertaken. The recited operation sequence makes clear that the plain and ordinary meaning of “target value” is not as Dr. Wooley opines because the particular operating condition that a device is in at a particular time is represented by the measurement taken by the sensor, 11 Some claim language less relevant to construing “target value” was omitted for ease of reference. which the controller then uses to determine whether the measurement satisfies the “target value.” Additionally, claim 1 recites that the “target value” is sent as part of a command to the controller. The “target value” is not sent to the controller from the sensor, as might be expected if the plain and ordinary meaning of “target value” were as Dr. Wooley opines. Petitioner and Dr. Wooley’s construction would also result in “target value” meaning effectively the same thing as the measurement of the fluid by the sensor, a concept that is separately recited in claim 1 and to which the “target value” is compared. The Specification of the ’680 patent does not support Petitioner’s understanding of the plain and ordinary meaning of “target value.” Although the Specification does not recite “target value,” it recites “target state,” and describes “target state” sufficiently to understand the plain and ordinary meaning of “target” as used in “target value” and “target state.” In particular, the ’680 patent explains that “[i]n some embodiments, the process 104 includes receiving, via a network interface, from a remote user device, (e.g., via a command-center server) a command to change a state of a fluid-handling device to a target state.” Ex. 1001, 11:48–51. This portion reflects that the command is seeking to change a state of a fluid-handling device to a target state. In other words, the “target value” or “target state” is not generally “the particular operating condition that a device is in at a particular time”; rather, it is a value or state that the fluid-handling device is desired to be in, as Patent Owner and Dr. Durham explain. Additionally, just as claim 1 recites a directional component for the “target value” to be sent to the controller in a command, so too does the Specification describe a “target state” as being sent in a command from a remote user device. Thus, the Specification clearly supports the plain and ordinary meaning proposed by Patent Owner and Dr. Durham and not the plain and ordinary meaning proposed by Petitioner and Dr. Wooley. slip op. at 14

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

      “time-stamped process data, report exception therein to the remote host, and extract and transmit time-stamped process data to the remote host.” Ex. 1005, Abst. (emphases added). Almadi explains that its remote field systems must include a plurality of controller units “to issue commands to, and gather and process data from a plurality of field devices, including remote systems and instruments, . . . [and] a database server for the storage of process data retrieved from the remote subsystems and instruments.” Id. at 2:22–30 (emphases added). Based on these disclosures, we agree with Patent Owner that Petitioner has not established that Almadi discloses element [1.4]. Specifically, the teachings from Almadi identified by Petitioner refer to process data, which is data retrieved from the remote subsystems/field devices. Thus, we understand that Almadi’s teaching—of using an Ethernet switch to transmit “process data”—describes transmitting data from the remote subsystems/field devices. See Ex. 1005, 3:13–17, cited in Pet. 15. But claim 1 and particularly element [1.4], recites “sending, with the server, the target value to the network address [which identifies a controller of the fluid-handling device13] via the network,” which is different than sending process data from the field devices to the remote host or database server for storage.” slip op. at 19

    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 11,175,680
  • Tanklogix, LLC v. SiteproInstitution denied
    PTAB · Oct 10, 2025 · IPR2025-00650 · APJ Sheila F Mcshane · IPR · Institution

    The Board denied institution because Petitioner did not show a reasonable likelihood that claims 18–32 and 34 were unpatentable over Kahn or Kahn and Gutierrez.

    RulingsInstitution decision
    • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied

      “information presented in the petition . . . and any response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a) (2024). Upon consideration of the Petition, the Preliminary Response, and the evidence of record, we determine that Petitioner has not established a reasonable likelihood of prevailing with respect to the unpatentability of at least one claim of the ’871 patent. Accordingly, for the reasons that follow, we decline to institute an inter partes review of claims 18–32 and 34 of the ’871 patent.” slip op. at 2

    • Skill levelSkill level patent owner adoptedDecided for patent owner

      “The respective proposed levels of qualifications for a person of ordinary skill in the art are similar, with Patent Owner proposing two years of experience compared to Petitioner proposing significant experience with remotely controlling fluid-handling devices, like SCADA systems. Patent Owner also proposes more extensive experience in lieu of educational experience. While we find Petitioner’s proposed qualifications to be acceptable, we adopt Patent Owner’s proposed qualifications for the purposes of this Decision because they offer a wider range of qualifications that nonetheless comport with the level of skill necessary to understand and implement the teachings of the ’871 patent and the asserted prior art. Our analysis and findings herein, however, do not turn on any differences in the qualifications adopted.” slip op. at 8

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

      “We determine that we need not expressly construe any claim terms to resolve the parties’ disputes on the current record. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 10

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

      “actuators and the remote control of fluid handling devices, including the receipt with the user-interface module of “a user command to actuate an actuator via a presented control interface” (limitation [18.7]) and “account authorized to send commands to remotely control fluid handling devices” (limitation [18.11]). We agree with Patent Owner that the Petition fails to demonstrate that Kahn discloses or teaches these limitations because the evidence does not provide support that there is remote control of fluid handling devices or the use of a user command on a control interface to send a command to a fluid handling device, for instance. Kahn is directed to providing access to fluid sensing data and analyzing and providing visual information on that data, but we do not discern that it teaches or discloses the capability to remotely control fluid handling devices. See, e.g., Ex. 1005, code (54), 1:27–36, 2:50–3:2. More specifically, the Kahn disclosures that Petitioner repeatedly relies upon for allegedly teaching this control are deficient. See Ex. 1005, 10:62–67, 14:35– 15:2, 15:62–16:32; see also Pet. 12–14, 16–18. Kahn discloses that “the communication unit 112B can include on-site alerts such as optical (indicator lights), audible alerts (e.g., alarm sounds), tactile (e.g., vibration of the unit) or can be interfaced to an appropriate control valve for simply shutting off the supply of fluid upon the detection of emergency events, for instance.” Ex. 1005, 10:62–67. Communication unit 112B is part of the local “sensor unit,” wherein the detection conditions determined by the sensor are communicated to remote devices by communication unit 112B. See id. at 3:31–33, 5:62–6:2, 6:27–35, 7:33–37, 13:7–12, Figs. 1A–1C. Kahn discloses that the sensor units, which include communication units 112B, can be located near shut-off valves and can communicate with distant locations. See id. at 11:1–13. There are no disclosures, however, in the above passages that there is remote control of fluid handling devices, that there is a user command on a control interface that actuates an actuator, or that there is a command sent to the facility actuators via a network connection, as required in limitations [18.5]–[18.7] and [18.9]–[18.12], respectively. Rather, the disclosure indicates that the communication unit 112B includes on-site alerts and that the local (non-remote) communication unit 112B can be interfaced with the control valve.” slip op. at 18

    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 10,488,871
Page 1 of 17
← Previous12345…Next →

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.