- Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00187 · APJ Debra L Dennett · IPR · Final written decision
Claims 1–17 are unpatentable under § 103, principally because Chang in view of Jin renders them obvious; the Jin/Feldmann grounds were not shown.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49).” slip op. at 10
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11
- Expert testimonyPatent owner expert creditedDecided for patent owner
“gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard. Without an apparent reason to modify the teachings of Jin and Feldmann to” slip op. at 19
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 17
Patent outcomesUS 10,230,009 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,230,009 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00006 · APJ Debra L Dennett · IPR · Final written decision
Claims 1–17 are unpatentable under § 103, principally over Chang and Jin; the Board rejected the Jin and Feldmann combinations for lack of a reason to combine.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’009 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’009 patent and the prior art.” slip op. at 10
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 26. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 116 with Pet. 26). Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” See Magnum, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard.” slip op. at 19
- Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable
“configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” Resp. 42 (citing Ex. 1013 ¶ 76). In so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Id. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Chang ¶ 62; Tr. 15:20–17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 73, 217 (citing Ex. 1023 § 1). Chang also discloses that the emitter area may be formed by thermal diffusion, ion implantation or the like. Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding a tunneling layer and a base surface field area from periphery region and isolation region. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” slip op. at 32
Patent outcomesUS 10,230,009 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,230,009 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00918 · APJ Avelyn M Ross · IPR · Final written decision
Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board rejected the Jin and Feldmann based grounds for lack of a reason to combine without hindsight.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable
“base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16
- Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable
“Patent Owner focuses on Chang’s description in paragraph 76 of a single configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” PO Resp. 42–43 (citing Ex. 1013 ¶ 76). But, in so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Ex. 1013 ¶ 62; Tr. 15:20– 17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 70–81, 91–96, 200 (citing Ex. 1026 § 1 and stating that “[b]oth Chang and Jin likewise teach backside isolation regions”). Chang also discloses that the emitter area may be formed by “thermal diffusion, ion implantation or the like.” Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Pet. Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding the second tunneling layer and a base surface field area from periphery region and isolation portion. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art “reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” Ex. 1003 ¶ 201.” slip op. at 33
Patent outcomesUS 9,722,104 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,722,104 - Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentablePTAB · Apr 15, 2026 · IPR2025-00007 · APJ Avelyn M Ross · IPR · Final written decision
Claims 1–11 are unpatentable under §103 over Chang and Jin because the combination teaches the claimed isolation portion and the claimed tapering.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedOther
“Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightTeaching away not foundNot shown unpatentable
“On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16
- Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner
“However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide.” slip op. at 18
Patent outcomesUS 9,722,104 unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,722,104 - Syngenta Crop Protection AG v. Inflexion Point Technologies, LLCInstitution deniedPTAB · Dec 1, 2025 · PGR2025-00045 · APJ Debra L Dennett · PGR · Institution
The Board denied institution because Petitioner did not show it was more likely than not that any challenged claim was unpatentable under the asserted grounds.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied
“We have authority to determine whether to institute a post-grant review under 35 U.S.C. § 324. Institution of a post-grant review is authorized by statute only when “the information presented in the petition . . . would demonstrate that it is more likely than not that at least 1 of the claims challenged in the petition is unpatentable.” 35 U.S.C. § 324(a). The burden is on Petitioner to show that the challenged patent is eligible for postgrant review. Mylan Pharms. Inc. v. Yeda Research & Dev. Co., PGR2016- 00010, Paper 9 at 10 (PTAB Aug. 15, 2016) (holding that the ultimate burden of persuasion remains with a petitioner to demonstrate that the challenged patent is eligible for post-grant review). Upon consideration of the Petition, Preliminary Response, and the cited evidence, we determine that Petitioner has not shown that it is more likely than not that any of the challenged claims are unpatentable. We thus determine to not institute a post-grant review of the ’027 patent based on the Petition.” slip op. at 2
- Skill levelSkill level petitioner adoptedOther
“a Bachelor of Science degree in Agricultural or Mechanical Engineering with 2–4 years of practical, applied experience in the field of agricultural machinery, including systems integration and fluid handling and sprayer control systems, or equivalent experience. Prelim. Resp. 12 (citing Ex. 2001, ¶ 59). Patent Owner states that the differences in the asserted levels of ordinary skill should not change the outcome of the Petition. Id. For the purposes of this decision, we adopt Petitioner’s definition, which appears consistent with the level of skill shown in the prior art references of record and the ’027 patent. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (explaining that specific findings regarding ordinary skill level are not required “where the prior art itself reflects an appropriate level and a need for testimony is not shown” (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163 (Fed. Cir. 1985))). Our analysis, however, would not change were we to adopt Patent Owner’s definition.” slip op. at 7
- Claim Construction › Intrinsic evidence (Phillips canons) › Lexicography (patentee as own lexicographer)Term construed board ownDecided for patent owner
“Patent Owner contends that claim construction is necessary for the “seed-applied substance” term because Petitioner allegedly ignores the teaching of the specification in evaluating the term. Prelim. Resp. 12. Patent Owner points to the specification, which defines a “seed-applied substance” as “includ[ing] any composition applied to seeds prior to the seeds being planted (e.g., when the seed comes in contact with the soil in a field).” Id. at 13 (quoting Ex. 1001, 7:45-48). Patent Owner contends that the term means “a substance that is applied directly to the seed before the seed comes into contact with the soil in a field.” Id. (citing Ex. 2001, ¶ 55). According to Patent Owner, Petitioner erroneously uses a definition that “allows the ‘seedapplied substance’ to be applied to the seed (and soil) as the seed lay planted in the soil.’” Id. For the purpose of addressing Petitioner’s grounds, we use the definition of “seed-applied substance” provided in the ’027 patent, i.e., “any composition applied to seeds prior to the seeds being planted (e.g., when the seed comes in contact with the soil in a field).” Vitronics Corp. v. Conceptronic, Inc., 90 F.3d 1576, 1582 (Fed. Cir. 1996) (“[A] patentee may choose to be his own lexicographer and use terms in a manner other than their ordinary meaning, as long as the special definition of the term is clearly stated in the patent specification or file history.”).” slip op. at 7
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable
“3. Analysis Our analysis of whether Wagers discloses the limitation “individually applying the desired application amount of the selected type of the seed-applied substance to each seed as it is being delivered to the soil” is dispositive of Petitioner’s challenge to claim 1 as anticipated.” slip op. at 10
Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites GrahamPatents in suitUS 12,102,027 - CQV Co., Ltd. v. Merck Patent GmbHNo claims unpatentablePTAB · Oct 14, 2025 · PGR2021-00054 · APJ Kristina M Kalan · PGR · Remand
Claims 1–22 were not shown unpatentable because Sample C was not proven publicly available as prior art, and the original decision found the remaining grounds insufficient.
RulingsRemand decision- Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication not establishedNot shown unpatentable
“We agree with Patent Owner that Petitioner’s evidence in Kuntz (Ex. 1026), the Annual Report (Ex. 1028), Masuko (Ex. 1029), and Pfaff (Ex. 1034) is insufficient to show that Xirallic® Sample C was available to the public before the effective filing date of the ’861 patent. Petitioner has not asserted, nor do we find, that any of these documents refer to or describe the lot of Xirallic® from which Sample C was taken. See Final Dec. 26. Kuntz, the Annual Report, Masuko, and Pfaff may support a finding that the Xirallic® line of products was available to the public, but these documents do not support a finding that the lot of Xirallic® from which Sample C was taken was available to the public. We also agree with Patent Owner that the Technical Data Sheets (Exs. 1005–1010), Certificates of Analysis (Exs. 1011–1017), and Material Safety Data Sheet (Ex. 1025) are insufficient to show that Xirallic® Sample C was available to the public. Petitioner has not asserted, nor do we find, that any of these documents refer to or describe the lot of Xirallic® from which Sample C was taken. See Final Dec. 26–27. Regardless of how the Technical Data Sheets were used in the Opposition against the European counterpart of the ’861 patent (Exs. 1040, 1041) and during the prosecution of the application from which the ’861 patent issued (Ex. 1003, 102–104), the Technical Data Sheets do not refer to or describe the lot of Xirallic® from which Sample C was taken. Moreover, as noted by Patent Owner, the Technical Data Sheets (Exs. 1005–1010) indicate that they are “preliminary” and Petitioner has not provided any evidence that the Technical Data Sheets were ever issued to the public, as opposed to just issued internally. See PO Resp. 18–19. We also find persuasive Patent Owner’s argument that the Technical Data Sheets are preliminary because other, later-dated technical data sheets (Exs. 2012, 2013) lack the “preliminary” label and list characteristics that are different from those in Exhibits 1005–1010. See PO Resp. 19 (comparing, e.g., Ex. 1009 and Ex. 2013; Ex. 1005 and Ex. 2012). The Technical Data Sheets may support a finding that the Xirallic® products they describe existed as of the dates on the documents, but they do not support a finding that the lot of Xirallic® from which Sample C was taken was available to the public.” slip op. at 20
- Expert testimonyPetitioner expert discountedPatent owner expert creditedOther
“witnesses. See Elbit Systems of Am., LLC v. Thales Visionix, Inc., 881 F.3d 1354, 1358 (Fed. Cir. 2018) (citing Trs. of Columbia Univ. v. Illumina, Inc., 620 F. App’x 916, 922 (Fed. Cir. 2015); Inwood Labs., Inc. v. Ives Labs., Inc., 456 U.S. 844, 856 (1982)). We have reviewed the witness testimony in the record and, more particularly, Mr. Choi’s deposition answers regarding Petitioner’s purchase of the lot of Xirallic® from which Sample C came. We find that Mr. Choi’s responses cast doubt on the credibility of his declaration testimony, namely with regard to the public availability of Sample C. Mr. Choi represented that he was involved in the purchase of the lot of Xirallic® from which Sample C was taken. Ex. 2011, 48:1–23. Mr. Choi stated that he instructed Petitioner’s marketing team manager to buy the sample from a distributor of Patent Owner’s products located in Europe. Id. at 48:24–49:4. Mr. Choi stated that he has evidence of the transaction, but refused to reveal the name of the company from which Petitioner purportedly purchased the lot of Xirallic® (id. at 49:5–50:3) and refused to produce an email in his possession that would corroborate his testimony regarding Petitioner’s acquisition of the product (id. at 50:8–16, 51:10–23). Mr. Choi represented that he does not remember how much Petitioner paid for Sample B. Id. at 56:4–5. Mr. Choi admitted that the entity from which Petitioner acquired the lot of Xirallic® from which Sample C was taken is “not currently a Merck distributor” (Ex. 2011, 50:4–7) and was not “a Merck distributor at the time” that “samples B and C were purchased” (id. at 51:25–52:2). According to Mr. Choi, the company is a “former distributor” of Patent Owner’s products. Id. at 52:3–6. Mr. Choi did not know, according to his testimony, when that unnamed entity first obtained the lot of Xirallic® (id. at 52:7–10) and he stated that he did not have personal knowledge of how the entity obtained the lot of Xirallic® (id. at 52:12–19). Instead, Mr. Choi assumed the entity was “able to obtain the sample through the routine course or process” the entity uses “to take samples or get samples.” Id. at 52:12–19. Mr. Choi believed the sample of Xirallic® from which Sample C was taken was sealed when Petitioner received it because samples from dealers are sealed, and he remembered observing that the package was from a dealer. Id. at 52:24– 54:25. However, Mr. Choi admitted that he did not obtain a technical data sheet or certificate of analysis for the lot of Xirallic® from which Samples B and C were taken. Id. at 59:6–11. Mr. Choi also answered questions regarding Petitioner’s purchase of Samples D and H. Ex. 2011, 62:20–66:8, 67:7–9, 73:12–13, 73:17–22. Similar to his testimony regarding Samples B and C, Mr. Choi admitted withholding an email regarding the purchase of the lot of Xirallic® from which Sample D was taken. Id. at 62:20–63:9. Mr. Choi also admitted that he did not know how Akzo USA or Axalta obtained the Xirallic® the companies sold to him, and admitted that Akzo USA was not a distributor of Patent Owner’s products at the time Petitioner purchased the product. Id. at 63:10–66:8, 73:17–22. Mr. Choi also admitted that Petitioner did not pay Akzo USA for the lot of Xirallic® from which Sample D was taken, and did not pay Axalta for the lot of Xirallic® from which Sample H was taken. Id. at 67:7–9, 73:12–13. Although Petitioner presents declaration testimony from Mr. Choi representing that he purchased the lot of Xirallic® from which Samples B and C were taken in October 2011 (Ex. 1004 ¶ 16), Mr. Choi’s declaration testimony lacks corroborating evidence, and his deposition testimony does not support that the product was available to the public, as we found in our Final Written Decision. See Final Dec. 27–28. Notably, Petitioner produced corroborating evidence for Mr. Choi’s acquisition of Samples A, H, and I. See Ex. 1004 ¶¶ 13 (citing Ex. 1047), 18 (citing Exs. 1024, 1025). However, Mr. Choi withheld similar evidence for the Xirallic® lots from which Samples B, C, and D were taken. See Ex. 2011, 50:8–16, 51:10–23, 62:20– 63:9; Final Dec. 28. As Patent Owner argues, there is “no information to determine when a contract was established, that there was consideration for the exchange, that the product was available to be delivered when the alleged transaction took place, or even when the product was delivered. Choi has no memory of what was paid for the product.” Sur-Reply 24–25; see also PO Resp. 13–14; PO Br. Rem. 2–4.” slip op. at 34
- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable
“Based on the evidence discussed above, we are not persuaded that Petitioner has shown by a preponderance of the evidence that Sample C was available to the public. Regardless of whether a company avoids wasting shelf life of its products (Ex. 1004 ¶¶ 15–16), there is no persuasive evidence in the record showing that the lot of Xirallic® from which Sample C was taken was released from quality control and then made available to the public by Patent Owner. Mr. Choi’s testimony shows that Petitioner obtained the lot of Xirallic® from which Sample C was taken in an atypical manner (i.e., not from Patent Owner or one of Patent Owner’s current distributors) (Ex. 2011, 49:5–50:7, 50:8–16, 51:10–23, 51:25–52:6, 52:12– 19), and there is no evidence in the record to show that the lot of Xirallic® was intended for sale, rather than for experimental use only or for some other restricted use. Accordingly, we determine Petitioner has not demonstrated by a preponderance of the evidence that Sample C qualifies as prior art against the ’861 patent, and we determine that Petitioner has not shown by a preponderance of the evidence that the ’861 patent is unpatentable over the grounds relying on Sample C.” slip op. at 38
Patent outcomesUS 10,647,861 not shown unpatentable§ 102 anticipation§ 103 obviousnessPatents in suitUS 10,647,861 - PTAB · Sep 9, 2025 · IPR2025-00389 · APJ Kevin W Cherry · IPR · Institution
The Board instituted IPR of claims 1–22 on all asserted grounds after finding a reasonable likelihood that at least one challenged claim would be shown unpatentable as obvious.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“institute an inter partes review. The standard for instituting an inter partes review is set forth in 35 U.S.C. § 314(a), which provides that an inter partes review may not be instituted unless “there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” The Supreme Court has held that the Board, in a decision to institute under 35 U.S.C. § 314(b), may not institute review on less than all claims challenged in the petition. SAS Inst. Inc. v. Iancu, 138 S. Ct. 1348, 1355–56 (2018). Moreover, in accordance with our rules, “[w]hen instituting inter partes review, the Board will authorize the review to proceed on all of the challenged claims and on all grounds of unpatentability asserted for each claim.” 37 C.F.R. § 42.108(a) (2025); see also PGS Geophysical AS v. Iancu, 891 F.3d 1354, 1360 (Fed. Cir. 2018) (interpreting” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“contends that a person of ordinary skill in the art for the ’498 patent “would have had a Bachelor’s Degree in Physics or an Engineering field relevant to battery technology (e.g., Electrical or Mechanical Engineering) and at least two years of industry experience in lithium-ion battery manufacturing and/or design.” Pet. 3 (citing Ex. 1003 ¶¶ 27–30).” slip op. at 11
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner “does not believe any claim terms require specific construction.” Pet. 10–11. Patent Owner states “no claim construction is necessary to deny institution because Patent Owner’s arguments for denial do not rely on the outcome of an actual controversy about claim interpretation.” Prelim. Resp. 10. Having considered the record, we determine that no express claim construction is necessary for any claim terms. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (holding that only claim terms in controversy need to be construed, and only to the extent necessary to resolve the controversy (citing Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 11
- Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner
“Patent Owner may be correct that the invention Takemura discloses seeks to improve on the “conventional” design disclosed in Figures 8 and 9, and, as part of its description of its inventions, Takemura discloses a variety of benefits to its approach over the approach disclosed in Figures 8 and 9. However, that does not negate the teachings provided in Figures 8 and 9. “A reference must be considered for everything it teaches by way of technology and is not limited to the particular invention it is describing and attempting to protect.” EWP Corp. v. Reliance Universal Inc., 755 F.2d 898, 907 (Fed. Cir. 1985) (emphases in original). As Petitioner explains, Sato discloses the use of tape, but does not provide details regarding its precise size and placement. See Pet. 34–39. Petitioner relies on Takemura for teaching how such tape would be sized and placed. Id. Indeed, Takemura teaches that such a placement was used in “conventional” lithium-ion batteries at the time. “It’s not necessary to show that a combination is “the best option, only that it be a suitable option.” Intel Corp. v. Qualcomm Inc., 21 F.4th 784, 800 (Fed. Cir. 2021) (quoting PAR Pharm., Inc. v. TWI Pharms., Inc., 773 F.3d 1186, 1197–98 (Fed. Cir. 2014)). Here, Petitioner only relies on Takemura for teaching how the tape disclosed in Sato would be sized and placed. Although Takemura might teach a different ultimate approach, that does not diminish Takemura’s teachings of a known size and placement that was conventionally used in the art. “[I]f a technique has been used to improve one device, and a person of ordinary skill in the art would recognize that it would improve similar devices in the same way, using the technique is obvious unless its actual application is beyond his or her skill.” KSR, 550 U.S. at 417. Thus, we are not persuaded, on the current record, that Takemura teaches away from the particular combination that has been proposed.” slip op. at 24
Claim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,923,498 - PTAB · Aug 26, 2025 · IPR2025-00432 · APJ Kevin W Cherry · IPR · Institution
The Board instituted IPR of claims 1–19 on all asserted grounds after finding a reasonable likelihood that at least one challenged claim is unpatentable.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“institute an inter partes review. The standard for instituting an inter partes review is set forth in 35 U.S.C. § 314(a), which provides that an inter partes review may not be instituted unless “there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” The Supreme Court has held that the Board, in a decision to institute under 35 U.S.C. § 314(b), may not institute review on less than all claims challenged in the petition. SAS Inst. Inc. v. Iancu, 138 S. Ct. 1348, 1355–56 (2018). Moreover, in accordance with our rules, “[w]hen instituting inter partes review, the Board will authorize the review to proceed on all of the challenged claims and on all grounds of unpatentability asserted for each claim.” 37 C.F.R. § 42.108(a) (2020); see also PGS Geophysical AS v. Iancu, 891 F.3d 1354, 1360 (Fed. Cir. 2018) (interpreting the statute to require “a simple yes-or-no institution choice respecting a petition, embracing all challenges included in the petition”). Applying those standards, and upon considering the Petition, the Preliminary Response, and the evidence of record, we determine the information presented a reasonable likelihood that Petitioner would prevail in establishing the unpatentability of at least one of the challenged claims of the ’148 patent. Accordingly, we institute an inter partes review.” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“Relying on the declaration testimony of Dr. Gido, Petitioner contends that an ordinarily skilled artisan for the ’148 patent “would have had at least a bachelor’s degree or equivalent degree from an accredited institution in chemistry, chemical engineering, materials science, or a similar discipline covering relevant principles of organic and inorganic chemistry, polymer processing, ceramic materials, and ceramic processing” and “three or more years of experience in electrochemical energy storage devices, lithium-ion battery technology, separators, characterizations and analyses of particle size, film thickness, and/or materials compositions, battery performance characterization, or other applications of polymer chemistry, ceramic chemistry, and ceramic processing.” Pet. 14. Petitioner additionally contends “[m]ore education could substitute for less experience, and vice versa.” Id. (citing Ex. 1003 ¶ 17). Patent Owner “adopts the definition proposed by the Petitioner.” Prelim. Resp. 14. Based on this record, we adopt Petitioner’s articulation of the level of ordinary skill in the art, which is consistent with the ’148 patent and the asserted prior art, and we apply it in our obviousness evaluations below. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art, itself, can reflect appropriate level of ordinary skill in art). We note that our decision would be the same applying either party’s definition of a person of ordinary skill in the art.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner contends that “[n]o claim terms require express construction.” Pet. 14–15. Patent Owner does not at this time address claim construction. See Prelim. Resp. 14–15. Having considered the record, we determine that no express claim construction is necessary for any claim terms. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (holding that only claim terms in controversy need to be construed, and only to the extent necessary to resolve the controversy (citing Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))). We note, however, there may be some claim terms below whose constructions that the parties may wish to address during trial.” slip op. at 11
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundInstituted
“Petitioner has shown sufficiently that there would be a motivation to combine Murakami and Beard with a reasonable expectation of success. As Petitioner explains, Beard teaches particular benefits of its porous structure that a person of ordinary skill in the art would be motivated to combine with the teachings of Murakami. See Pet. 54–56. At this stage, Patent Owner’s counterarguments do not undermine this showing. To begin with, we note that Patent Owner appears to mischaracterize the combination as incorporating Beard’s cell structure into Murakami, when it is merely to incorporate Beard’s technique of closely packing inorganic particles in the cell walls into Murkami. Thus, at this stage and on the current record, Patent Owner’s arguments about alleged incompatibilities between Beard’s and Murakami’s particle size distributions, amounts of binder, and binding and dispersion processes are not persuasive. As for the contentions regarding Figure 2, we note that Petitioner does not rely on Figure 2, which appears to include the incorporation of fibers. Thus, it is unclear why the pore structure of Figure 2 would be relevant to the combination that Petitioner proposes. Finally, we find that Petitioner has shown sufficiently, on this record, that Petitioner has shown a reasonable expectation of success. As Petitioner and its expert explain, Beard and Murakami teach similar manufacturing techniques (which are also similar to the ’148 patent), and Beard and Murakami provide ample detail on how to implement their techniques. See Ex. 1003 ¶¶ 167–172; Ex. 1010 ¶¶ 57–60; Ex. 1005 ¶¶ 71–72. We find this level of detail adequate, at this stage, to show that a person of ordinary skill would have a reasonable expectation of success in making the combination. See Pfizer Inc. v. Apotex, Inc., 480 F.3d 1348, 1365 (Fed. Cir. 2007) (noting that “the expectation of success need only be reasonable, not absolute”).” slip op. at 37
Claim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,575,148 - Zhuhai Cosmx Battery Co., Ltd. v. Ninge Amperex Technology LimitedInstitution deniedPTAB · Aug 20, 2025 · IPR2025-00385 · APJ Debra L Dennett · IPR · Institution
The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–10 were anticipated by Nishikawa or obvious over the asserted combinations.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied
“review under 35 U.S.C. § 314 (2018); 37 C.F.R. § 42.4(a). The standard for instituting an inter partes review is set forth in 35 U.S.C. § 314(a), which provides that an inter partes review may not be instituted “unless the Director determines . . . there is a reasonable likelihood that the petitioner would prevail with respect to at least [one] of the claims challenged in the petition.” For the reasons set forth below, upon considering the Petition and Preliminary Response, we determine that Petitioner has not established a reasonable likelihood of prevailing with respect to at least one challenged claim. Accordingly, we deny the Petition and decline to institute an inter partes review.” slip op. at 2
- Skill levelSkill level petitioner adoptedOther
“Petitioner contends that A person of ordinary skill in the relevant art would typically hold an advanced degree in chemistry, material science, and/or a related discipline, and have at least two years of experience with designing and/or fabricating battery separators or have an equivalent level of education, training, and experience. Pet. 5. Patent Owner “adopts the definition proposed by Petitioner” for the purposes of the Preliminary Response. Prelim. Resp. 22. In light of the record before us, and for purposes of this Decision, we adopt Petitioner’s unopposed definition because it is consistent with the specification. We note that neither party indicated that the result would change under any different definition.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Absolute plastic deformation rate” and “relative plastic deformation rate” are the only claim terms disputed in this proceeding, and are clearly defined in the Specification and in claim 1. See Spec. 4:22–27, 4:47–54; 25:31–37. Because we determine that claim construction is not necessary to decide whether to institute, we do not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review). slip op. at 11
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable
“Petitioner’s arguments are unconvincing. Petitioner points to nothing in Nishikawa that allows a POSITA to determine L2 (defined as “a length of 4 Tensile strength is measured as force per units area, such as MPa or psi. One MPa equals one N/mm2. Nishikawa Table 1 discloses tensile strength in N/cm. Ex. 1004 Table 1. Petitioner makes calculations to convert the reported N/cm into N/m2 and then to GPa, but provides no explanation for why tensile strength is reported in N/cm or how it was measured. See Pet. 31. the porous substrate after the porous substrate is stretched to breakage and docked along the fracture caused by the breakage and flattened”) or L2 – L0. See generally Pet., Ex. 1004. Petitioner and its expert, Dr. Pecht, fail to adequately explain why tensile strength divided by Young’s modulus is “a proxy for L1 – L2” or why such a proxy is sufficient to disclose the limitation as stated. Instead, we are required to rely on “approximations” and “estimates” with insufficient explanation of why such they are appropriate or adequate. See Pet. 26, 30, 32; see also Ex. 1003 ¶¶ 97, 105–108, 111.” slip op. at 13
Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,964,927 - PTAB · Jul 16, 2025 · PGR2025-00012 · APJ Debra L Dennett · PGR · Institution
Instituted PGR on claims 1–3 based on five grounds; the Board found each ground met the institution threshold on the preliminary record.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“We have authority to determine whether to institute a post-grant review under 35 U.S.C. § 324. Institution of a post-grant review is authorized by statute when “the information presented in the petition . . . would demonstrate that it is more likely than not that at least 1 of the claims challenged in the petition is unpatentable.” 35 U.S.C. § 324(a). A post-grant review may also be instituted when “the petition raises a novel or unsettled legal question that is important to other patents or patent applications.” See id. § 324(b). Applying that standard on behalf of the Director (37 C.F.R. § 42.4(a)) and in consideration of the Petition, Preliminary Response, and the evidence of record, we determine that the information presented shows that it is more likely than not that Petitioner would prevail in establishing unpatentability of claims 1–3 of the ’201 patent.” slip op. at 2
- Skill levelSkill level board ownOther
“At this stage of the proceedings, neither Petitioner’s nor Patent Owner’s proffered definitions of the level of skill appear appropriate. Petitioner’s proposal requires as little as a bachelor’s degree in organic chemistry and two years of experience as a laboratory technician working on development of molecules with targeted biological activity, and an ambiguous “understanding” of certain processes. Patent Owner’s proposal, other the other hand, requires multiple years of both formal training and actual, practical experience in highly specialized fields that involve detection of optical or radiolabeled compounds and use of molecular imaging techniques such as PET and SPECT. For the purposes of this decision, on the record at this time, we find that a POSA would have had a Ph.D. in chemistry, biochemistry, or a comparable field or an M.D., and at least four years of experience in chemical synthesis of compounds that may be used to target biologically-significant tissues. This definition appears consistent with the level of skill shown in the prior art references of record. See Daiichi Sankyo Co. v. Apotex, Inc., 501 F.3d 1254, 1256 (Fed. Cir. 2007). The parties will have the opportunity to cross-examine Dr. Martin and Dr. VanBrocklin in this proceeding to develop a full record for us to determine the weight that each expert’s testimony should be given. We invite the parties to further brief the definition of a POSA here, and whether we should discount either experts’ testimony due to lack of qualifications.” slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Other
“c) Analysis On the present record, we find that “low molecular weight” is not limited to Patent Owner’s proposed “from about 50 Daltons to about 1,500 Daltons.” The cited evidence relied on in the Pomper Declaration all concerns metabolomics and metabolites, and we find no reason that even a vague definition of metabolites applies to the claimed compounds. See Ex. 1002, ¶ 102. Moreover, the uncontested fact that several of the B moieties alone—without the A moiety or L linker—specifically identified in the ’201 patent fall outside of Patent Owner’s proposed definition is persuasive (see id., ¶ 103), as we normally do not interpret claim terms in a way that excludes examples disclosed in the specification. See, e.g., Verizon Servs. Corp. v. Vonage Holdings Corp., 503 F.3d 1295, 1305 (Fed. Cir. 2007) (rejecting proposed claim interpretation that would exclude disclosed examples in the specification). In addition, the opinion stated in the Pomper Declaration that “the term of ‘low molecular weight’ is well accepted in the chemical arts’” and the declarant “recognize[s] that low molecular weight compounds would have a molecular weight of typically form about 50 Daltons to about 1,500 Daltons” is offered by a co-inventor. We, as factfinder, have discretion to weigh the credibility of expert witnesses and to give each item of evidence such weight as appropriate. See In re Am. Acad. of Sci. Tech Ctr., 367 F.3d 1359, 1368 (Fed. Cir. 2004) (“[T]he Board is entitled to weigh the declarations and conclude that the lack of factual corroboration warrants discounting the opinions expressed in the declarations.”). In this case, we find that the published references on metabolites do not support the opinion. In re Am. Acad. of Sci. Tech Ctr., 367 F.3d at 1368 (Fed. Cir. 2004) (“[T]he Board is entitled to weigh the declarations and conclude that the lack of factual corroboration warrants discounting the opinions expressed in the declarations.”) The Pomper reference (Ex. 1006) also uses the term “low molecular weight”—without further characterization of the term—and is uninformative as to the meaning of the term. See Ex. 2002, ¶ 60; Ex. 1006, ¶ 12. The table giving the molecular weight of a “selection of compounds disclosed by Pomper” (see Ex. 2002, ¶ 62) is not persuasive in defining “low molecular weight,” as it does not explain how those included were “selected” and does not include molecular weights for all of the examples.7 In addition, Patent Owner’s definition does not appear to apply to all claimed compounds.8 7 At least one of the examples (SRV73) not included in the table appears to have a molecular weight well over “about 1,500 Daltons.” 8 See, e.g., claim 113 of Ex. 1006. Patent Owner’s arguments distinguishing “low molecular weight” slip op. at 11
- Claim Construction › Intrinsic evidence (Phillips canons) › Lexicography (patentee as own lexicographer)Term construed petitioner constructionDecided for petitioner
“The ’201 patent defines “alkyl” as “a straight (i.e., unbranched) or branched chain, acyclic or cyclic hydrocarbon group, or combination thereof” “ that has “the number of carbon atoms designated (i.e., C1–C10 means one to ten carbons, including 1, 2, 3, 4, 5, 6, 7, 8, 9, and 10 carbons)” and “[i]n particular embodiments, the term ‘alkyl’ refers to C1-20 inclusive, including 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, and 20 carbons” “unless otherwise stated.” Ex. 1001, 39:44–58. Although substituents at the R1x position in the claims are limited to “C1-6alkyl,” those at position R3x are not. Ex. 1001, Certif. Corr. Patent Owner’s representation that “Jansen I provides ‘the following definitions’ stating that ‘alkyls groups of this invention comprise from 1 to 6 carbon atoms’” is inaccurate. See Prelim. Resp. 19. In fact, Jansen I states: The term “alkyl” by itself or as part of another substituent refers to a fully saturated hydrocarbon of Formula CxH2x+1 wherein x is a number greater than or equal to 1. Generally, alkyl groups of this invention comprise from 1 to 6 carbon atoms. Alkyl groups may be linear or branched and may be substituted as indicated herein. When a subscript is used herein following a carbon atom, the subscript refers to the number of carbon atoms that the named group may contain. Ex. 1007, 22:16–23 (emphasis added). Neither the ’201 patent nor its incorporation by reference of Jansen I would have conveyed to a POSA that the “(CO)alkyl” of the substituent in the R3x position in the claims is intended to comprise from one to six carbon atoms or is limited to any particular length and size. “(C(O)alkyl,” having no number of carbon atoms designated, means” slip op. at 15
Claim construction§ 103 obviousness§ 112 disclosurecites Phillips · KSR · Graham · NautilusPatents in suitUS 11,938,201
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.