PTAB
Advanced fields
41 decisions · 568msnewest first
  • PTAB · Jan 17, 2025 · IPR2024-00597 · APJ Jon B Tornquist · IPR · Final written decision

    Claims 2–4 and 6–18 are unpatentable as obvious over Abe and Guyomard, with claims 9–10 also obvious over Iwaizono; claims 1 and 5 were not shown unpatentable.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Petitioner contends that a person of ordinary skill in the art “would have had a Master’s degree in material science, chemical engineering, chemistry, or similar field with four years of experience designing testing, and building secondary lithium batteries.” Pet. 11 (citing Ex. 1002 ¶ 51). Petitioner further contends that a person of ordinary skill in the art would have been aware of “(1) positive electrode materials, (2) negative electrode materials, (3) separators, (4) electrolytes, (5) charge-discharge parameters, and (6) protection circuits, as well as ‘battery failure modes’ such as plating and the formation of dendrites.” Id. (citing Ex. 1002 ¶¶ 50–51). Patent Owner “does not dispute Petitioner’s level of ordinary skill.” PO Resp. 17. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the disclosures of the ’641 patent and the prior art of record.” slip op. at 9

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

      “We also agree with Patent Owner that the charge cut-off voltage is not necessarily the applied voltage during charging. PO Resp. 20. Rather, depending on the charging protocol used and when in the charging cycle the voltage is applied, the applied voltage could be higher than the battery voltage. Ex. 2013; Ex. 2006 ¶ 91. For example, as discussed in more detail below with respect to the Uemura grounds, when fast charging using constant current is used and the charging rate is not slow, the applied voltage will be higher than the battery voltage when the constant current charging phase is stopped. Ex. 2006 ¶ 91; Ex. 2013. Likewise, during constant current/constant voltage charging, the applied voltage approximates the battery voltage only when the battery is nearly completely charged. Ex. 2013; Ex. 2006 ¶ 91. Thus, the applied voltage may be, but is not necessarily, the charge cut-off voltage. In view of the foregoing, we construe “charge cut-off voltage” in claims 1 and 5 as “the maximum value to which the battery is configured to be charged.” PO Resp. 18; Ex. 2008, 217:6–11; Pet. Reply 5. Contrary to Patent Owner’s arguments, however, we do not understand the phrase “configured to be charged” to necessarily represent a single voltage for the battery that is determined based on the structure and chemistry of the battery. Pet. Reply 4–5. Rather, the charge cut-off voltage is a selected potential, or voltage, of the battery or cell at the end of charging that is controlled by a circuit or device, such as a charger or control circuit within the battery. Ex. 1001, 9:50–55; Ex. 1048, 2, 7–8; Ex. 1008, 3:9–13. And, for the reasons discussed herein, the charge cut-off voltage may be, but is not necessarily, the same as the applied voltage during charging. PO Resp. 20.” slip op. at 15

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

      “charge cut-off voltage “greater than 4.2 V but less than 5.8 V” and calculating a specific or theoretic capacity “with a charge cut-off voltage limited to 4.2” (claim 1) or “with a charge cut-off voltage set at 4.2 V” (claim 5). Ex. 1001, 16:56–61, 17:6–11. Although the parties dispute the precise scope of these claim terms, the parties agree that the first use of “charge cut-off voltage” in claims 1 and 5 refers to the potential of the battery as a whole (between the cathode and the anode), and not a half-cell voltage using lithium metal as a counter electrode.10 Tr. 17:1–3 (agreeing 10 With respect to the phrase “as calculated by a theoretic capacity with a charge cut-off voltage set at 4.2 V,” the parties in fact appear to be in that the first use of “charge cut-off voltage” in claim 5 refers to a full-cell voltage); Sur-reply 5; PO Resp. 22. We need not further construe the claims to resolve the disputes between the parties. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 16

    • Expert testimonyPatent owner expert creditedDecided for patent owner

      “Given Mr. Juzkow’s unambiguous testimony that Uemura uses constant current charging that would stop when the applied voltage reached 11 The chart is reproduced from SAFT, Charging your lithium-ion batteries: 5 expert tips for a longer lifespan, (https://www.saft.com/energizing-iot/charging-your-lithium-ion-batteries-5-expert-tips-longerlifespan#:~: text=When%20the%20battery%20provides%20current,This%20restore s%20the%20battery's%20capacity). 4.3 V, as well as Dr. Yao’s persuasive testimony that Uemura’s constant charging rate is not slow, we credit the testimony of Dr. Yao that one of ordinary skill in the art would have understood that the internal voltage to which the battery of Uemura was charged is less than 4.3 V. Ex. 2006 ¶ 119. In particular, Dr. Yao persuasively testifies that one of ordinary skill in the art would have believed that the charge cut-off voltage was no more than 4.2 V, and most likely equal to “about 4 V.” Id. ¶¶ 119–122.” slip op. at 21

    Patent outcomesUS 7,749,641 mixed
    Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
    Patents in suitUS 7,749,641
  • PTAB · Jan 17, 2025 · IPR2023-01183 · APJ Jon B Tornquist · IPR · Final written decision

    Claims 2–4 and 6–18 are unpatentable as obvious over Abe and Guyomard, with claims 9 and 10 also obvious over Iwaizono; claims 1 and 5 were not shown unpatentable.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Petitioner contends that a person of ordinary skill in the art “would have had a Master’s degree in material science, chemical engineering, chemistry, or similar field with four years of experience designing testing, and building secondary lithium batteries.” Pet. 11 (citing Ex. 1002 ¶ 51). Petitioner further contends that a person of ordinary skill in the art would have been aware of “(1) positive electrode materials, (2) negative electrode materials, (3) separators, (4) electrolytes, (5) charge-discharge parameters, and (6) protection circuits, as well as ‘battery failure modes’ such as plating and the formation of dendrites.” Id. (citing Ex. 1002 ¶¶ 50–51). Patent Owner “does not dispute Petitioner’s level of ordinary skill.” PO Resp. 17. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the disclosures of the ’641 patent and the prior art of record.” slip op. at 9

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

      “constructions. First, we agree with Petitioner that the ’641 patent indicates that the charge cut-off voltage selected for a particular battery need not be a fixed property of the battery or something that is set by the design and chemistry of the battery. Consistent with this conclusion, the ’641 patent discloses that a “charging device controls the charge cut-off voltage of the single lithium-ion cell within a range from 4.3 V to 5.8 V.” Ex. 1001, 9:50– 55. This strongly suggests that the charge cut-off voltage is controlled by the charger and is not necessarily an inherent property of the battery. Patent Owner contends that this is merely an unclaimed embodiment, but the relevant disclosure states that the charging device for the “present invention” may be any type of device “with the proviso that said charging device controls the charge cut-off voltage.” Id. at 9:50–53.” slip op. at 12

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

      “charge cut-off voltage “greater than 4.2 V but less than 5.8 V” and calculating a specific or theoretic capacity “with a charge cut-off voltage limited to 4.2” (claim 1) or “with a charge cut-off voltage set at 4.2 V” (claim 5). Ex. 1001, 16:56–61, 17:6–11. Although the parties dispute the precise scope of these claim terms, the parties agree that the first use of “charge cut-off voltage” in claims 1 and 5 refers to the potential of the battery as a whole (between the cathode and the anode), and not a half-cell voltage using lithium metal as a counter electrode.10 Tr. 17:1–3 (agreeing 10 With respect to the phrase “as calculated by a theoretic capacity with a charge cut-off voltage set at 4.2 V,” the parties in fact appear to be in that the first use of “charge cut-off voltage” in claim 5 refers to a full-cell voltage); Sur-reply 5; PO Resp. 22. We need not further construe the claims to resolve the disputes between the parties. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 16

    • Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner

      “Given Mr. Juzkow’s unambiguous testimony that Uemura uses constant current charging that would stop when the applied voltage reached 11 The chart is reproduced from SAFT, Charging your lithium-ion batteries: 5 expert tips for a longer lifespan, (https://www.saft.com/energizing-iot/charging-your-lithium-ion-batteries-5-expert-tips-longerlifespan#:~: text=When%20the%20battery%20provides%20current,This%20restore s%20the%20battery's%20capacity). 4.3 V, as well as Dr. Yao’s persuasive testimony that Uemura’s constant charging rate is not slow, we credit the testimony of Dr. Yao that one of ordinary skill in the art would have understood that the internal voltage to which the battery of Uemura was charged is less than 4.3 V. Ex. 2006 ¶ 119. In particular, Dr. Yao persuasively testifies that one of ordinary skill in the art would have believed that the charge cut-off voltage was no more than 4.2 V, and most likely equal to “about 4 V.” Id. ¶¶ 119–122. Petitioner argues that because the battery of Uemura is charged “to” a maximum voltage of 4.3 V, Uemura discloses the claimed charge cut-off voltage under either Petitioner’s or Patent Owner’s construction of the term. Pet. Reply 11–12 (citing Ex. 1009 ¶ 81; Ex. 1044 ¶¶ 56–59). This argument is not persuasive because Mr. Juzkow unambiguously testified that charging in Uemura stopped when the applied voltage reached 4.3 V, and Uemura discloses that the battery was charged “at” a voltage ranging from 4.3 V to 2.0 V, not “to” such a voltage. Ex. 1009 ¶ 81; Ex. 2008, 113:2–13; Ex. 2006 ¶ 119 n.64; Sur-reply 9. In view of the foregoing, we determine that Petitioner has not demonstrated by a preponderance of the evidence that Uemura anticipates independent claims 1 and 5 of the ’641 patent.” slip op. at 21

    Patent outcomesUS 7,749,641 mixed
    Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
    Patents in suitUS 7,749,641
  • PTAB · Oct 11, 2024 · IPR2024-00771 · APJ Grace Karaffa Obermann · IPR · Institution

    The Board instituted IPR on claims 1–6 of the ’195 patent on all asserted grounds and granted Texas Instruments’ motion to join the Cirrus IPR.

    RulingsInstitution decision
    • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted

      “Because the Preliminary Response in the instant case includes arguments pertaining to the sufficiency of the asserted prior art references, which were not raised in the preliminary response in the Cirrus IPR, we briefly address below the patentability of the challenged claims.” slip op. at 6

    • PTAB / AIA Trials › §315(b) time barNot time barredDecided for petitioner

      “II. TIMELINESS OF THE PETITION UNDER 35 U.S.C. § 315(B) Pursuant to 35 U.S.C. § 315(b), “[a]n inter partes review may not be instituted if the petition requesting the proceeding is filed more than 1 year after the date on which the petitioner, real party in interest, or privy of the petitioner is served with a complaint alleging infringement of the patent.” Patent Owner argues that the Petition is untimely under 35 U.S.C. § 315(b) because Petitioner is in privity with time-barred entities. Prelim. Resp. 10– 30. However, 35 U.S.C. § 315(b) also provides that the one-year time bar “shall not apply to a request for joinder under subsection (c).” See also 37 C.F.R. § 42.122(b). Because the Petition is accompanied by a timely request for joinder (Paper 2) to the instituted proceeding (IPR2024-00017), which we grant as further discussed below, Patent Owner’s argument that the Petition is time-barred under 35 U.S.C. § 315(b) is moot, irrespective of whether Petitioner is in privity with time-barred entities.” slip op. at 5

    • PTAB / AIA Trials › Joinder §315(c) / SAS all-or-nothingJoinder, grantedGranted

      “B. Whether to Join Petitioner as a Party to the Cirrus IPR Joinder may be authorized when warranted, but the decision to grant joinder is discretionary. See 35 U.S.C. § 315(c); 37 C.F.R. § 42.122. A motion for joinder should (1) set forth reasons why joinder is appropriate; (2) identify any new grounds of unpatentability asserted in the petition; (3) explain what impact (if any) joinder would have on the trial schedule for the existing review; and (4) address specifically how briefing and discovery may be simplified. See, e.g., Kyocera Corp. v. Softview LLC, IPR2013- 00004, Paper 15 (PTAB April 24, 2013). As the moving party, Petitioner bears the burden of proving that it is entitled to the requested relief. 37 C.F.R. § 42.20(c). As an initial matter, we find the Motion for Joinder meets the timing requirements of 37 C.F.R. § 42.122(b) because Petitioner filed it on April 4, 2024, no later than one month after the Cirrus IPR was instituted on May 1, 2024.” slip op. at 9

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successNot reached

      “5. “Aid the Movement of Minority Carriers” Patent Owner argues that the Petition fails to show that the applied prior art references disclose the claim limitations “requiring ‘aid the movement of minority carriers,’” as twice recited in claim 1. Prelim. Resp. 8. Patent Owner summarizes this dispute as follows: The challenged patent discloses and claims a semiconductor device with (among other things) a “drift layer having a graded concentration of dopants . . . [and] further having a first static unidirectional electric drift field to aid the movement of minority carriers.”[] The Petition should not be instituted, because (among other deficiencies) it fails to show that the prior art discloses the “aid the movement of minority carriers” claim limitation. Rather than pointing to anything in the prior art that would teach this claim limitation, the Petition assumes that any “graded concentration of dopants” would necessarily “aid the movement of minority carriers.” The Petition contains no analysis explaining why the “graded concentration of dopants” in the prior art meet the “aid the movement of minority carriers” limitation, apart from the fact that they are “graded concentration of dopants.” In other words, Petitioner reads the “aid the movement of minority carriers” limitation out of the claims completely. Id. at 1–2. Patent Owner includes additional details in support of its view that the asserted prior art fails to establish obviousness of the “aid carrier movement” limitations of claim 1. Prelim. Resp. 1–10.” slip op. at 8

    § 102 anticipation§ 103 obviousness
    Patents in suitUS 8,421,195
  • PTAB · Sep 10, 2024 · IPR2023-00502 · APJ Grace Karaffa Obermann · IPR · Final written decision

    Claims 1–16 are unpatentable as obvious over the combined disclosures of Yoakim, Jarisch, and Rapparini.

    RulingsFinal written decision
    • Novelty / Anticipation (§102) › Priority / effective filing date / continuation supportDecided for petitioner

      “To obtain the benefit of the filing date of an earlier application, Patent Owner bears the burden of producing evidence to establish where each limitation of the challenged claims is disclosed in a single priority application. Studiengesellschaft Kohle, 112 F.3d at 1564; NTP, 654 F.3d at 1276. Petitioner identifies limitations of the challenged claims that are missing from each individual German priority application. Pet. 39–42. Patent Owner responds with no evidence or arguments suggesting that the identified limitations are disclosed in a single application. Resp. 10–12. On this record, no challenged claim is entitled to the benefit of the filing date of any of the three German priority applications; therefore, Jarisch qualifies as prior art under at least 35 U.S.C. § 102(e).” slip op. at 19

    • Expert testimonyPetitioner expert creditedPatent owner expert discountedDecided for petitioner

      “In other words, even if we accept that Dr. Howle has some experience designing medical devices and components, and that those experiences represent work designing products similar to mechanical beverage systems, Patent Owner fails to direct the Board to evidence sufficient to establish that this experience, in the aggregate, amounts to “at least five years” or involved “experience with sensors for recognizing identifiers.” Dec. 8 (adopting Patent Owner’s own proposed definition of ordinary skill in the art); see Sur-reply 3 (citing Ex. 1066, 34:16–35:9; Ex. 1067, 101:3–12, 102:30– 104:9; Ex. 2017 ¶¶ 3, 4) (failing to establish adequately, if at all, how Dr. Howle’s qualifications include the requisite minimum five-year period of relevant design experience). Accordingly, we determine that Dr. Howle is not qualified to offer expert testimony from the perspective of a person having ordinary skill in the art in this proceeding.12 Kyocera Senco Indus. Tools Inc. v. Int’l Trade Comm’n, 22 F.4th 1369, 1376–78 (Fed. Cir. 2022). The Federal Circuit has made plain that, “[t]o offer expert testimony from the perspective of a skilled artisan in a patent case,” including the issue of patent “validity,” the “witness must at least have ordinary skill in the art.” 12 To be clear, we are not saying that a witness supplying expert opinions must have satisfied the requirements of the level of ordinary skill in the art on or before the priority date of the challenged patent, which Patent Owner seems to understand. See Sur-reply 4–5. Instead, we evaluate whether Dr. Howle had at least the requisite qualifications of a person having ordinary skill in the art by the time he rendered his opinions. Osseo Imaging, LLC v. Planmeca USA, Inc., Appeal No. 2023-1627, slip op. at 7 (Fed. Cir. Sept. 4, 2024) (“[A]n expert can acquire the necessary skill later and develop an understanding of what a person of ordinary skill knew at the time of the invention,” however, where “the expert was not a person of ordinary skill at the time of the invention may well be used during cross-examination to undermine the credibility of the expert.”); see id., slip op. at 5–6 (affirmatively quoting Kyocera). Id. (Board’s emphasis). “Without that skill, the witness’[s] opinions are neither relevant nor reliable.” Id. at 1377. “‘Admitting testimony from a person . . . with no skill in the pertinent art serves only to cause mischief and confuse the factfinder.’” That testimony would ‘amount[ ] to nothing more than advocacy from the witness stand.’” Id. (quoting Sundance, Inc. v. DeMonte Fabricating Ltd., 550 F.3d 1356, 1362, 1364–65 (Fed. Cir. 2008)). Alternatively, even if we accept that Dr. Howle possesses “at least five years” of relevant design experience, on this record, we agree with Petitioner that his opinions are entitled to less weight than those of Petitioner’s witness, Mr. Jobin. Reply 27. Unlike Dr. Howle, Mr. Jobin is a designer by profession, with more than 30 years of industry experience. Reply 27 (citing Ex. 1003 ¶¶ 5–30). For example, Mr. Jobin designed a home-based beer dispensing system utilizing cartridge identification technologies. Id. (citing Ex. 1003 ¶ 24). Mr. Jobin also “has substantial experience with sensors for recognizing identifiers.” Id. (citing Ex. 1003 ¶ 19; Ex. 1072, 3712–19, 67:22–70:19). Dr. Howle, by contrast, “has never designed a beverage machine.” Reply 22; see generally Sur-reply (declining to contest that assertion).13” slip op. at 14

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner

      “In Petitioner’s contrary view, Jarisch teaches how to move a code in a centrifugal brewing system to the bottom of the flange and how to configure a light-conductive material so that the detector’s light source will reach the bottom of the flange. Pet. 45–46; Reply 21–22 (Ex. 1003 ¶¶ 194–195; Ex. 1005 ¶¶ 82–84, Fig. 5). Although Figure 61 of Yoakim discloses a flare in its brewing chamber, bodily incorporation is not required, and we are directed to no persuasive argument or evidence that Yoakim could not be configured with a straight chamber, as depicted in Figure 5 of Jarisch. We credit the testimony of Mr. Jobin that a person of ordinary skill in the art would have sought to place the code at the bottom of the flange and would have had a reasonable expectation of success in so doing. Ex. 1003 ¶ 184. For reasons explained above, we assign little or no weight to Dr. Howle’s conflicting testimony because he has little or no experience designing a mechanical beverage system or similar product. See supra 10– 16. Petitioner lays out persuasive reasons why Dr. Howle’s testimony, on this particular point, is “conclusory” and rests on “bodily incorporation” of the references. Reply 24; see id. at 22–24 (pointing out with particularity fundamental flaws in Dr. Howle’s opinions); In re Mouttet, 686 F.3d 1322, 1332 (Fed. Cir. 2012) (“It is well-established that a determination of obviousness based on teachings from multiple references does not require an actual, physical substitution of elements.”); In re Nievelt, 482 F.2d 965, 968 (CCPA 1973) (“Combining the teachings of references does not involve an ability to combine their specific structures.”). In addition, Patent Owner contends that Yoakim requires that the capsule holder be capable of receiving a set of multiple volume capsules and that there is a “snug fit” to avoid “unbalances.” Sur-reply 8 (citing Ex. 1004 ¶¶ 205, 479, 484, 507, 512). According to Patent Owner, Petitioner does not explain adequately how the use of Jarisch’s “straight chamber” with a capsule holder that does not engage with the side wall of the capsule would allow insertion of multiple volume capsules or permit a “snug fit” in the modified device of Yoakim. Id. at 8–9. Patent Owner’s view that Yoakim discloses the use of certain capsules which might not fit into a device with Jarisch’s non-flared structure is ineffective to undercut the sufficiency of Petitioner’s showing on this point. Petitioner is not seeking a bodily incorporation of Yoakim and Jarisch and, in any event, other embodiments of Yoakim do not require the type of flared capsule identified by Patent Owner. Ex. 1004, Fig. 63. Furthermore, we credit the testimony of Mr. Jobin that one of ordinary skill in the art would have understood how to design the chamber of Yoakim to allow reading of a barcode on the underside of the flange. Ex. 1003 ¶¶ 187–195. With respect to the argument that the use of Jarisch’s design would not allow a snug fit, we are directed to no persuasive evidence that Jarisch’s lack of contact between the capsule side wall and the holder would render the device inoperable or less effective. Resp. 39–40; see Reply 22 (citing Ex. 2019, 36:18–37:6). Indeed, as Petitioner points out, Jarisch indicates that its device, including its capsule holding means, allows the capsule to be successfully driven in rotation. Reply 22 (citing Ex. 1005 ¶ 23).” slip op. at 49

    • Obviousness (§103) › Analogous artAnalogous artDecided for petitioner

      “That argument is not persuasive. A reference need not identify or discuss another prior art patent or application in order for that reference to be deemed relevant or analogous art. Nor do we endeavor to determine why, or why not, a particular reference is discussed in a prior art reference. The analogous art inquiry focuses on reasonable pertinence and involves assessing the similarities between the claimed invention and the prior art, including the problems addressed and the closeness of the subject matter, as viewed by an ordinarily skilled artisan. Donner Tech., LLC v. Pro Stage Gear, LLC, 979 F.3d 1353, 1360 (Fed. Cir. 2020); see Airbus S.A.S. v. Firepass Corp., 941 F.3d 1374, 1380-81 (Fed. Cir. 2019) (relevant analysis focuses on comparing the disclosed embodiments, function, and structure of the claimed invention to the disclosures of the prior art). Against that backdrop, we reject Patent Owner’s suggestion that the inquiry involves whether the inventors of Jarisch saw a need to discuss Yoakim’s disclosure in Jarisch’s priority document.” slip op. at 45

    Patent outcomesUS 10,994,923 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
    Patents in suitUS 10,994,923
  • PTAB · Aug 27, 2024 · IPR2023-00521 · APJ Jon B Tornquist · IPR · Final written decision

    Claims 19–61, 63–77, and 79 are unpatentable as anticipated by Doud; claims 78, 80, and 81 are not shown unpatentable. The contingent motion to amend is granted in part and denied in part.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Petitioner contends that a person of ordinary skill in the art “would have at least a Ph.D. in chemistry, metallurgy, or material science or material engineering” or, in the alternative, “would have a Bachelor of Science or Master of Science degree in one of these disciplines plus experience involving the use and design of dissolvable metal alloys for use in creating tools and other downhole parts for well drilling or completion activities.” Pet. 13–14. Patent Owner does not oppose Petitioner’s contentions regarding the level of ordinary skill in the art. PO Resp. 12 n.4. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the ordinarily skilled artisan as it is consistent with the prior art of record.” slip op. at 7

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

      “With respect to claim 19, Petitioner proposes constructions for the terms “in situ precipitate” and “a plurality of particles of said in situ precipitate having a size of no more than 50 µm.” Pet. 11–12. With respect to claims 76–81, Petitioner proposes a construction for the term “wherein said additive material includes one or more metal materials selected from the group consisting of 0.1–35 wt. % copper, 0.1–24.5 wt. % nickel and 0.1–20 wt. % cobalt.” Id. at 13. Patent Owner contends no claims require construction for purposes of this Decision. PO Resp. 12 n.4, 17–18; Mot. 16–17. Upon review of the prior art of record, we determine that no claim terms require express construction for purposes of this Final Written Decision. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 8

    • Disclosure Requirements (§112) › Written description (Ariad)Written description inadequateWritten description adequateMixed

      “Ex. 2027, 20:25–21:5 (emphasis added). The disclosure that the “magnesium composite” of “[t]he present invention” “includes at least 50 wt% magnesium” is unambiguous and constitutes strong evidence that the inventors were not in possession of a magnesium composite with less than 50 wt. % magnesium, or additive concentrations above 50 wt. %. See SciMed Life Systems, Inc. v. Advanced Cardiovasular Systems, Inc., 242 F.3d 1337, 1343 (Fed. Cir. 2001) (noting that a description of the “present invention” as having a particular structure “is strong evidence that the claims should not be read to encompass the opposite structure”). Consistent with this conclusion, the original claims of the ’295 application all limited the additive material in the composite to 0.05 wt %–45 wt %. Ex. 2027, 26:1– 13, 29:9–15. Likewise, in each example where copper, nickel, or cobalt additives are used in the range recited in the proposed substitute claims, the magnesium composite is “over 50 wt% magnesium,” and any claims that do not require this range of magnesium are limited to an additive range of “about 0.05 wt%–45 wt% of said mixture.”8 Ex. 2027, 6:13–7:4, 7:16–19, 8 Written description support is considered from the view point of the ordinarily skilled artisan. Ariad Pharms., Inc. v. Eli Lilly and Co., 598 F.3d 1336, 1351 (Fed. Cir. 2010) (en banc). Patent Owner, bearing the burden to show written description support in any priority application for which it seeks the benefit of its filing date, provides no testimony from an ordinarily skilled artisan regarding written description support in the ’295 application, or any evidence to show what such an artisan would conclude from the express disclosures of the ’295 application. Lectrosonics, Paper 15 at 7; In re NTP, 654 F.3d 1268, 1276 (Fed. Cir. 2011) (noting that “a patent’s claims are not entitled to an earlier priority date merely because the patentee claims priority . . . Rather, for a patent’s claims to be entitled to an earlier priority date, the patentee must demonstrate that the claims meet the requirements of 35 U.S.C. § 120”). Where there is any ambiguity in the disclosures of the ’295 application, the absence of supporting testimony tends to cut against 26:2–31:2; see Ex. 1005 ¶¶ 12, 13, 18, 19, 16–21, 26, 28, claims 16–21, 26– 28. In view of the foregoing, we are not persuaded that Patent Owner has demonstrated that the inventors of the priority applications were in possession of a magnesium cast composite that included less than 50 wt. % magnesium, or greater than 50 wt. % additives. As proposed substitute claim 104 encompasses a magnesium cast composite with up to 90 wt. % additives, and therefore as little as 10 wt. % magnesium, Patent Owner has not demonstrated that the full scope of this claim finds written description support in any application prior to the ’915 application, filed on October 12, 2018.” slip op. at 17

    • Disclosure Requirements (§112) › Definiteness (Nautilus)DefiniteIndefiniteMixed

      “The definiteness requirement of § 112(a) is satisfied when “a patent’s claims, viewed in light of the specification and prosecution history, inform those skilled in the art about the scope of the invention with reasonable clarity.” Nautilus, Inc. v. Biosig Instruments, Inc., 572 U.S. 898, 910 (2014); see 37 C.F.R. § 42.100(b) (changing the claim construction standard used to review a claim proposed in a motion to amend from the broadest reasonable construction to the “same construction standard that would be used to construe the claim in a civil action under 35 U.S.C. [§] 282(b)”). Proposed substitute claim 104 generically requires “in situ precipitate” and also a specific type of in situ precipitate: “in situ galvanically-active intermetallic precipitate.” Mot. Appendix A. Although this claim would have best been clarified by Patent Owner after seeking preliminary guidance on its Motion to Amend, upon review of the written description, claims, and figures of the ’740 patent, as well as Patent Owner’s clarification in its Reply to the Opposition, we agree with Patent Owner that one of ordinary skill in the art would have understood that the “in situ galvanically-active intermetallic precipitate” is merely a more complete description of the “in situ precipitate” mentioned earlier in the sentence. Mot. Reply 4. As such, we do not find that this part of proposed substitute claim renders claim 104 indefinite.” slip op. at 22

    Patent outcomesUS 10,689,740 mixed
    Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Graham · Nautilus
    Patents in suitUS 10,689,740
  • PTAB · May 22, 2023 · PGR2022-00009 · APJ Monica S Ullagaddi · PGR · Final written decision

    Claims 1–5, 7–12, and 14–19 are unpatentable based on lack of written description, anticipation by Bruning, or obviousness over Bruning and Kabel.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “lighting device.” Accordingly, we determine that the level of ordinary skill in the art is “a bachelor’s degree in electrical engineering, or similar technical field, with two years of relevant experience in the field of design and/or development of LEDs and circuits,” as Petitioner proposes and that “the field of design and/or development” would be “in the context of lighting devices” as Patent Owner proposes, in which “[a]n increase in experience could compensate for less education.” Id.; Pet. 24 (citing Ex. 1002 ¶ 46).” slip op. at 15

    • Claim Construction › Intrinsic evidence (Phillips canons) › Prosecution history disclaimer / disavowalDisclaimer foundDecided for patent owner

      “theoretically fall under the “or greater” portion of the amended claim limitation “forward voltage of 6V or greater,” Applicant distinguished Colby on the basis that the 120V AC voltage from a wall outlet is not “the minimum voltage difference required between the anode and cathode of the LEDs in the claimed circuit to allow current to flow through the LEDs.” See Ex. 1023, 9 (emphasis added). Applicant’s argument specifically identifies the claim language at issue––“forward voltage of 6V or greater”––and specifically states that it is not disclosed because Colby does not disclose the minimum voltage and instead, discloses something else, something larger–– 120V AC voltage. Accordingly, we conclude that Applicant disclaimed any voltage that is more than “the minimum voltage difference required between the anode and cathode of the LEDs in the claimed circuit to allow current to flow through the LEDs” from the scope of “forward voltage.”” slip op. at 25

    • Disclosure Requirements (§112) › Written description (Ariad)Written description inadequateUnpatentable

      “4. 35 U.S.C. § 112(a) With respect to the written description requirement, we are persuaded” slip op. at 32

    • Disclosure Requirements (§112) › Enablement (Wands, Amgen full scope)Not enabledUnpatentable

      “Basis § Unpatentable Unpatentable Lack of written description, 3, 10, 17 112(a) 3, 10, 17 Lack of enablement 3, 10, 17 112(b) Indefiniteness 3, 10, 17 Lack of written description, 4, 11, 18 112(a) 4, 11, 18 Lack of enablement 4, 11, 18 112(b) indefiniteness 4, 11, 18” slip op. at 77

    Patent outcomesUS 10,932,341 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · KSR · Graham · Nautilus
    Patents in suitUS 10,932,341
  • PTAB · May 10, 2023 · IPR2021-01575 · APJ Jon B Tornquist · IPR · Final written decision

    Claims 1–9 are unpatentable as obvious over the asserted combinations of Saito and Catalano, Saito and Wojnarowski, and those combinations with Johnson.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Petitioner contends a person of ordinary skill in the art as of the priority date of the ’551 patent “would have had at least a bachelor’s degree in electrical engineering, computer engineering, computer science, physics, or the equivalent, and two or more years of experience with LED devices and/or related circuit design, or a related field.” Pet. 9 (citing Ex. 1002 ¶¶ 19–20). For purposes of this proceeding, “Patent Owner does not dispute Petitioner’s definition of a [person of ordinary skill in the art].” PO Resp. 9. Upon review of the parties’ arguments, the prior art of record, and the ’551 patent, adopt Petitioner’s undisputed level of ordinary skill in the art in this proceeding.” slip op. at 6

    • Prior constructionPrior construction adoptedDecided for petitioner

      “In IPR2021-01367, which also is directed to the ’551 patent, the Board construed the term “driver” to mean “a program, circuitry, or device used to power other programs, circuits, or devices.” Home Depot USA, Inc. v. Lynk Labs, Inc., IPR2021-01367, Paper 8 at 11–14 (PTAB Feb. 14, 2023) (Institution Decision); see also IPR2021-01367, Paper 46 at 7 (Final Written Decision). Patent Owner believes that this construction is broader than that used by the ’551 patent, “but will nevertheless refer to this construction because it is helpful in resolving the disputes over the teachings of the prior art, because none of the prior art teaches or suggests a driver even under this broader construction.” PO Resp. 10–11. Patent Owner does not propose an alternative construction of the claim term. Id. Petitioner does not contest the adopted construction of “driver.” Pet. Reply 1. Upon review of the parties’ arguments and evidence, and for the reasons expressly set forth in IPR2021-01367, we construe “driver” to mean “a program, circuitry, or device used to power other programs, circuits, or devices.” No other claim terms require express construction. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 6

    • Novelty / Anticipation (§102) › Priority / effective filing date / continuation supportReference is prior artPriority date awardedDecided for petitioner

      “connector” to describe the 3-pin connector of Catalano was potentially ambiguous. Based on the full trial record, we are persuaded that the citations provided in the Petition provide sufficient evidence that the ’495 Provisional provides written description support for claim 23 of Catalano.11 In response to Patent Owner’s argument that Catalano’s 3-pin connector 612 is connected to bulb base 616, and there is no evidence that such a connector is used in “a conventional incandescent bulb” (Sur-Reply 9), we find that regardless of the internal components connecting the “standard bulb base” to the LED circuit, the “standard bulb base” is a connector that can fit within “standard bulb sockets” and allow the device to replace a conventional incandescent bulb. Ex. 1006 ¶¶ 5–7. Therefore, it is “a standard bulb power connector equivalent to the power connector of a” slip op. at 14

    • Expert testimonyPetitioner expert creditedPatent owner expert discountedDecided for petitioner

      “Upon review of the record and the parties’ arguments as a whole, we agree with Petitioner that Saito discloses a driver, as that term is used in claim 1 of the ’551 patent. First, our construction of “driver” is broad, constituting any “program, circuitry, or device used to power other programs, circuits, or devices.” And, consistent with the structure of claim 1 of the ’551 patent, this construction does not require that the identified circuit or device actually generate power, only provide power to another device or circuit. switch that turns on or off a power source. Rather, the circuit of Saito monitors the voltage provided at both node A 107 and node B 715 and, depending on the reported voltages, switches between voltage sources to provide power to the LEDs. In this way, the voltage applied to the LED circuit is maintained within a range of roughly 16 and 30 Volts, and the LEDs are driven for a prolonged period of time by capacitors 106 and 107, which Saito explains “cut[s] down the consumption of electric current” and results in more efficient use of power. Ex. 1008 ¶¶ 98–103. We find persuasive Dr. Baker’s testimony that one of ordinary skill in the art would have considered such a circuit to be a “driver,” as recited in claims 1 and 5 of the ’551 patent. Ex. 1002 ¶¶ 94–95, 110–111.” slip op. at 23

    Patent outcomesUS 10,154,551 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 10,154,551
  • PTAB · Apr 19, 2023 · IPR2021-01576 · APJ Scott Raevsky · IPR · Final written decision

    Claims 1–12 are unpatentable as obvious; claims 13–18 are not shown unpatentable because the asserted combinations fail to teach or suggest multiple LED packages connected in series.

    RulingsFinal written decision
    • Skill levelSkill level patent owner adoptedDecided for patent owner

      “PO Resp. 8 (citing Ex. 2001 ¶¶ 41–42). Patent Owner argues that its definition is superior because Petitioner’s “and/or” qualifier “might be read as considering a person who has ‘related circuit design’ experience but no experience with ‘LED devices’ to be a POSITA.” Id. at 9. Patent Owner further views Petitioner’s “or a related field” phrasing as potentially including a person who has no experience with LED devices. Id. We agree with Patent Owner on both points. We agree with Patent Owner that Patent Owner’s proposal is more consistent with the problems and solutions in the ’979 patent and prior art of record. We adopt Patent Owner’s definition of the level of skill but note that had we adopted Petitioner’s level of skill, we would not have reached a different outcome here.” slip op. at 6

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

      “specification support its construction of “formed or mounted to” as encompassing indirect attachment to the substrate. Neither the plain claim language nor the specification requires the phosphor coating to be directly attached to the substrate. Limitation 1(c) recites, wherein the LED chips comprise a phosphor coating to produce a change in a color or a quality of light emitted from the LED chips, wherein the LED chips, the power connection leads, and the phosphor coating are formed or mounted to a flexible substrate that is sufficiently flexible to be formed into a cylindrical shape[.] Ex. 1001, 22:7–12 (emphasis added). The claim is inartfully written, as it requires the LEDs to comprise a phosphor coating but then separately recites that the LED chips and the phosphor coating are formed or mounted to the substrate. But Petitioner correctly explains that the plain meaning requires that “the LED chips comprise a phosphor coating” and that “the [same] phosphor coating” (included in the LED chips) is “formed or mounted to a flexible substrate.” Reply 2. In other words, the use of the term “the” before “phosphor coating” indicates reliance on the antecedent basis of “LED chips comprise a phosphor coating,” and thus the same coating of the LED chips is formed or mounted to the substrate. Logically, by including a phosphor coating with the LED chips, which are formed or mounted to the substrate, the coating of these chips is also indirectly formed or mounted to the substrate. Conversely, it would be illogical to conclude that the claim recites two phosphor coatings, one attached to the LED chips and another attached directly to the substrate, because the structure of the claim refers to a single phosphor coating of the LED chips. Even Patent Owner concedes that the claim encompasses the phosphor coating indirectly being mounted or attached to the substrate (in addition to being directly attached). PO Resp. 11 (“The ordinary English reading of the claim language does not encompass the phosphor coating only being indirectly attached to the substrate, instead, the language indicates that the coating is directly applied to the substrate.” (emphasis changed)), 13 (“the phosphor coating . . . is not merely attached to the substrate indirectly”).” slip op. at 10

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

      “After considering Patent Owner’s arguments, which we address below, we agree with Petitioner that the combination of Wojnarowski and Martin discloses this limitation and that a person of ordinary skill in the art would have been motivated to combine the references’ teachings in the manner asserted by Petitioner. Briefly, we summarize our findings, and then we address the parties’ arguments in more detail. First, we agree with Petitioner, and Patent Owner does not dispute, that Wojnarowski’s AC input voltage would have been converted to DC voltage in light of the bridge rectifier and capacitor disclosed by Wojnarowski. Pet. 25; Ex. 1002 ¶¶ 119– 20 (citing, e.g., Ex. 1005, 7:59–62, Fig. 24); PO Resp. 35–36 (acknowledging Wojnarowski discloses converting an AC input to a DC voltage). Second, we further agree with Petitioner, and Patent Owner does not dispute, that excessive current due to too few LEDs would have harmed Wojnarowski’s LEDs, and too small a current due to too many LEDs would be insufficient to power Wojnarowski’s LEDs. Pet. 26; Ex. 1002 ¶ 134; PO Resp. 48 (discussing, but not disputing, these assertions).13 Third, we agree that a POSITA would have recognized in view of Martin’s teachings and the knowledge of a skilled artisan that when configuring Wojnarowski’s device, the total forward voltage drop of the series-connected LEDs should approximately match the DC voltage output 13 Petitioner explains the relationship between voltage and current for the LEDs as follows: “the total voltage drop of the circuit would dictate the current drawn by the LED circuitry, which would have been known to be inversely proportional to the voltage.” Pet. 26 (citing Ex. 1002 ¶ 134). of Wojnarowski’s circuit. Pet. 26–27 (citing Ex. 1002 ¶¶ 132–38; Ex. 1008, Abstract (LED voltage “must be matched to the input source voltage”), ¶ 60 (“For AC or any other regularly varying input voltage, there is an additional requirement to direct drive voltage matching”)). For example, Martin teaches that “[t]he number of LEDs in the monolithic array may be selected to achieve a particular voltage drop across each device.” Ex. 1006 ¶ 22. Martin further explains, “[t]he voltage across each of the individual LEDs in the array is the line voltage divided by the number of LEDs in series,” and “[t]he number of LEDs is chosen such that the maximum voltage across each individual LED during the peak in the alternating current cycle is low enough so as not to damage the LEDs.” Id. The forward voltage drop across Martin’s 38 LEDs is about 171 V, which matches Martin’s AC input voltage peak of about 169.71 V. See id. (“At 120 RMS volts, the peak voltage will be about 180V [correction: 169.71 V],” and if the LEDs “can tolerate a maximum forward voltage of 4.5V, at least 38 LEDs connected in series are required.” (38 LEDs x 4.5 V = 171 V)); PO Resp. 41–42 (“While Martin references ‘about 180V,’ both parties agree that the correct value of the peak voltage Vp is 169.71 V.” (citing Ex. 1002 ¶ 127)). Although Martin’s LED forward voltage drop (171 V) differs slightly from the peak input voltage (169.71 V), Patent Owner conceded at the hearing that the claimed “matches” does not require an exact equivalence. Tr. 38:9–11 (“Patent Owner agrees . . . that matching has a meaning that goes beyond exact equivalence.”).14” slip op. at 22

    • Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication establishedDecided for petitioner

      “35 U.S.C. § 311(b). PO Resp. 22–25. This statute provides that “[a] petitioner in an inter partes review may request to cancel as unpatentable 1 or more claims of a patent only on a ground that could be raised under section 102 or 103 and only on the basis of prior art consisting of patents or printed publications.” § 311(b) (emphasis added). Patent Owner contends that Martin is not available as prior art under 35 U.S.C. § 311(b) because it is not a patent or printed publication and is only prior art under 35 U.S.C. § 102(e). PO Resp. 22. Patent Owner argues that documents are “printed publications” as of the date they become available to the public, and Martin became public on its publication date of October 21, 2004, after the February 25, 2004 priority date of the ’979 patent. Id. at 23. Patent Owner raises a similar argument for the Soules-II reference in Ground 6. Id. at 25– 26. Petitioner responds that the AIA framework permits the use of § 102(e) prior art in IPR proceedings, unlike formerly available covered business method review (CBM) proceedings, which restricted challenges to § 102(a) prior art. Reply 29. We agree. The statute governing the formerlyavailable CBM proceeding explicitly limits challenges based on “prior art that is described by section 102(a).” AIA § 18(a)(1)(C). In contrast, § 311(b) more broadly permits challenges “on the basis of prior art consisting of patents or printed publications.” The broader language in § 311(b) implies that unlike CBMs, IPRs are not limited to challenges solely under § 102(a) prior art. The parties cite to no Federal Circuit decisions that squarely address this issue. However, the Federal Circuit has applied § 102(e) patent application publication prior art in appeals from IPR proceedings. See, e.g., Purdue Pharma L.P. v. Iancu, 767 Fed. App’x 918, 920–21, 926 (Fed. Cir. 2019) (nonprecedential) (determining that a § 102(e) patent application publication was available as prior art in an IPR). The Board has also long permitted challenges based on patent application publications under § 102(e). See, e.g., Idle Free Sys., Inc. v. Bergstrom, Inc., IPR2012-00027, Paper 14 at 27 (PTAB Jan. 31, 2013) (instituting trial over § 102(e) ground based on a patent application publication). We therefore find Patent Owner’s § 311(b) argument unpersuasive.” slip op. at 34

    Patent outcomesUS 10,652,979 mixed
    Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
    Patents in suitUS 10,652,979
  • PTAB · Mar 13, 2023 · IPR2021-01347 · APJ Jon B Tornquist · IPR · Final written decision

    Claims 1–17 and 21–25 are unpatentable: claims 6 and 24 are anticipated by Birrell; the remaining challenged claims are obvious over the stated combinations.

    RulingsFinal written decision
    • Skill levelSkill level patent owner adoptedDecided for patent owner

      “Patent Owner contends there are “several problems” with Petitioner’s proposed definition. PO Resp. 11. In particular, Patent Owner contends the “and/or” qualifier and addition of “or a related field” could be read to allow an individual with no experience with LED devices to be a person of ordinary skill in the art. Id. Upon review of the parties’ arguments, the prior art of record, and the ’298 patent, we agree with Patent Owner that one of ordinary skill in the art would have had experience working with LEDs and/or LED circuit design. Thus, we adopt Patent Owner’s definition of one of ordinary skill in the art. We note, however, that neither party asserts that the outcome of this case rests on resolving the small differences between the parties’ definitions of the ordinarily skilled artisan.” slip op. at 8

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

      “C. Claim Construction In this proceeding, the claims of the ’298 patent are construed “using the same claim construction standard that would be used to construe the claim in a civil action under 35 U.S.C. [§] 282(b).” 37 C.F.R. § 42.100(b). Under that standard, the words of a claim are generally given their “ordinary and customary meaning,” which is the meaning the term would have had to a person of ordinary skill at the time of the invention in the context of the 1303, 1312–13 (Fed. Cir. 2005) (en banc). Neither party contends any terms of the ’298 patent require construction. Pet. 5–6; PO Resp. 12. Upon review of the parties’ arguments and supporting evidence, we agree that no terms require express construction. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 8

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for petitioner

      “By its express language, the claim term “wirelessly” is best understood as “without the use of a wire.” We are directed to no disclosure in the written description or prosecution history that would contradict this conclusion or otherwise shed light on the meaning of this claim term. There is no dispute that capacitive coupling does not use a wire or any other form of direct contact to transmit power. Thus, the plain meaning of “wirelessly” encompasses capacitive coupling. This conclusion is supported 6,336,031 states that “[c]onnectionless (i.e., wireless) transmission of analog and digital signals has previously been accomplished using . . . [c]apacitive coupling.” Ex. 1131, 1:10–18. Likewise, U.S. Patent No. 6,988,026 describes a “power receiving system which receive[s] power wirelessly (inductively, through radio frequency energy transfer and/or capacitively).” Ex. 1133, 113:64–114:2. Mr. Credelle’s counter-testimony is not persuasive because he does not explain in any detail why one of ordinary skill in the art would not understand a capacitive coupling that transfers power to be a wireless system. See Ex. 2001 ¶ 80.” slip op. at 50

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner

      “KSR instructs that “[t]he combination of familiar elements according to known methods is likely to be obvious when it does no more than yield predictable results.” KSR, 550 U.S. at 416. Here, Petitioner proposes to substitute one known method of transmitting power for another (an inductor in place of two capacitors), according to known methods (Logan), and Patent Owner does not dispute that the combination would yield a predictable result of wirelessly providing power from one device to another. This suggests that the proposed combination would have been obvious. Id. point to a specific problem discussed in Birrell for which Logan’s method of using inductive coupling would be a solution. See In re Heck, 699 F.2d 1331, 1333 (Fed. Cir. 1983) (“The use of patents as references is not limited to what the patentees describe as their own inventions or to the problems with which they are concerned. They are part of the literature of the art, relevant for all they contain.”) (internal quotations omitted). What the Petition must demonstrate is that there was some reason why one of ordinary skill in the art would have sought to combine the elements in the manner proposed. KSR, 550 U.S. at 418. The Petition provides multiple, persuasive reasons (discussed above) as to why one of ordinary skill in the art would have sought to use inductors, as disclosed in Logan, to wirelessly transmit power to a lighting device, such as that disclosed in Birrell.13 (d) Conclusion For the reasons set forth above, we find that Petitioner presents multiple, persuasive reasons as to why one of ordinary skill in the art would have sought to implement the wireless power transmission system of Logan in the lighting device of Birrell.” slip op. at 19

    Patent outcomesUS 10,966,298 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
    Patents in suitUS 10,966,298
  • PTAB · Jan 18, 2023 · IPR2021-01370 · APJ Scott Raevsky · IPR · Final written decision

    Claims 9–17 are unpatentable: claims 9–11, 13, 15, and 17 are anticipated by Dowling; claims 9–15 and 17 are obvious over Dowling, Mueller, and Okuno; claims 9–11, 15, and 16 are anticipated by Ter Weeme.

    RulingsFinal written decision
    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for petitioner

      “Given the breadth of the claims and specification, as well as Patent Owner’s implicit prosecution acknowledgement, we find the intrinsic evidence dispositive in this case of the meaning of “disconnected” as encompassing an electrical disconnection sufficient to turn the LED circuit off, including an electronic switch like a transistor to perform the electrical disconnection.” slip op. at 13

    • Claim Construction › Intrinsic evidence (Phillips canons) › Preamble limiting or notPreamble limitingDecided for petitioner

      “Turning to our analysis, we start by addressing the interpretation of claim 9’s preamble, “[a]n LED lighting system.” Both parties brief the meaning of this preamble, but neither party addresses the threshold issue of whether the preamble is limiting. We note that “[g]enerally, a preamble is not limiting.” Summit 6, LLC v. Samsung Elecs. Co., 802 F.3d 1283, 1292 (Fed. Cir. 2015). However, among other exceptions to this general rule, our reviewing court has “repeatedly held a preamble limiting when it serves as antecedent basis for a term appearing in the body of a claim.” In re Fought, 941 F.3d 1175, 1178 (Fed. Cir. 2019) (citations omitted). The body of claim 9 refers back to the preamble by reciting, “wherein the LED lighting system is driven with the AC voltage source.” Ex. 1001, 20:25–26. As such, the body of the claim relies on the preamble for antecedent basis support, and we determine that the preamble of claim 9 is limiting.” slip op. at 47

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

      “Petitioner’s arguments are more persuasive. Dowling discloses mode switch 190, which, among other modes, can “strobe, that is, flash on and off,” LEDs in different colors. Ex. 1004 ¶¶ 47, 62. Dr. Neikirk testifies that this strobing action connects a red LED circuit to the AC voltage source, then disconnects it from the AC voltage source and connects a blue LED circuit to the AC voltage source. Ex. 1002 ¶ 39. Dr. Neikirk further testifies that Dowling discloses connecting and disconnecting the LED circuits to the AC voltage source via a controller that utilizes PWM to turn those circuits on and off. Ex. 1026 ¶ 27 (citing Ex. 1004, Figs. 1, 8, ¶¶ 38–43, 63). He further states, “[a]s I confirmed at my deposition, when a PWM transistor is off, it is off.” Id. (citing Ex. 2006, 33:17–25). Under the correct construction of “disconnected” set forth above, we find this evidence persuasive to show that Dowling discloses this limitation. Significantly, Dowling discloses, and Patent Owner does not dispute,8 that LEDs of 8 For the first time in the hearing, Patent Owner raised a new argument that “Petitioner [does not] point to any disclosure in Dowling that actually says that a mode turns an LED on and turns another LED circuit off.” E.g., Tr. 79:3–9. Relatedly, Patent Owner argues that Dowling’s “strobe mode” does not “cause[] some LED circuits to be connected and other LED circuits to be disconnected.” Id. at 80:21–81:2; see also id. at 81:3–83:12 (colloquy with counsel regarding the absence of a “strobe mode” discussion in the PO Response). These arguments came too late, and we do not consider them. See Dell Inc. v. Acceleron, LLC, 884 F.3d 1364 (Fed. Cir. 2018) (“Unless it different colors “flash on and off” in response to user selection of the mode switch, thereby teaching the claimed “second switch that allows the first LED circuit to be disconnected from the AC voltage source and a second LED circuit to be connected to an AC voltage source.” Ex. 1004 ¶¶ 47, 62.” slip op. at 23

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

      “We agree with Petitioner that the combination of Dowling, Mueller, and Okuno would have rendered claim 14 obvious. We find persuasive Petitioner’s contention that it would have been obvious to implement the power conversion circuitry disclosed by Dowling for light bulb 180 using at least one transformer as taught by Mueller and Okuno. Pet. 34–35 (citing Ex. 1002 ¶ 85). We agree that Dowling already discloses power conversion circuitry for a light bulb, which converts a 120 volts AC input to a DC voltage of 5 or 12 volts. Id. at 29–30 (citing Ex. 1004 ¶ 58; Ex. 1002 ¶ 62). Specifically, Dowling describes a connection 70 for its light bulb that “may include a converter to convert received power to power that is useful,” for example, “an AC to DC converter to convert one-hundred twenty Volts at sixty Hertz into a direct current at a voltage of, for example, five Volts or twelve Volts.” Ex. 1004 ¶ 58; see also id. ¶ 63 (“A power converter can be used within the light bulb 180 to convert the received power . . . in the form of a variable amplitude AC signal . . . to the requisite power for the control circuitry and the LEDs . . . .”). We also credit Dr. Neikirk’s testimony that “a POSITA would have been motivated to investigate the known implementation details in the art regarding how to convert the AC power from a much higher voltage down to an appropriate direct current at a much lower voltage for driving LEDs, and been led to the teachings of Mueller and Okuno.” Ex. 1002 ¶ 62, quoted in Pet. 30. We further credit Dr. Neikirk’s testimony that “[a] POSITA would have been motivated to use a transformer and bridge rectifier as taught by Mueller and Okuno, and recognized the suitability of those components, for Dowling’s power conversion circuity in an Edison-mount lightbulb.” Id. ¶ 64 (citing Ex. 1004, Fig. 8, ¶¶ 62–63), quoted in Pet. 30. In other words, based on Dowling’s teachings of using power conversion circuitry in its light bulb, one of ordinary skill in the art would have looked to Okuno and recognized the suitability of a transformer for use as Dowling’s power conversion circuitry. See id. ¶¶ 62–64.” slip op. at 38

    Patent outcomesUS 10,349,479 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
    Patents in suitUS 10,349,479
Page 1 of 5
← Previous12345Next →

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.