PTAB
Advanced fields
1,672 decisions · 733msnewest first
  • PTAB · Mar 16, 2026 · IPR2024-01402 · APJ Gregg I Anderson · IPR · Final written decision

    The Board held claims 3 and 8–19 unpatentable: claim 3 was anticipated by Yu and obvious on the stated grounds, and claims 3 and 8–19 were obvious over Burgener and Okashita, with or without Yu.

    RulingsFinal written decision
    • PTAB / AIA Trials › Motions to amend / substitute claimsMotion to amend, grantedGranted

      “Inc. (“Petitioner”) filed a Petition (Paper 1, “Pet.”) requesting an inter partes review of claims 1–19 of U.S. Patent No. 7,745,886 B2 (Ex. 1001, “the ’886 patent”). Petitioner filed a Declaration of Dr. Scott E. Thompson, Ph.D., in support of the Petition. Ex. 1002 (“Thompson Dec.”). Harbor Island Dynamic, LLC (“Patent Owner”) filed a Preliminary Response. Paper 7 (“Prelim. Resp.”). On April 4, 2025, we instituted this inter partes review as to the Challenged Claims and all grounds presented in the Petition. Paper 9 (“Inst. Dec.”). Following institution, Patent Owner filed a Response to the Petition (“PO Resp.”) limited to the patentability of the challenged claims. Paper 18. In support of the Patent Owner’s Response, Patent Owner filed a Declaration of John Berg. Ex. 2006. Patent Owner also filed an Unopposed Motion to Amend, cancelling claims 1, 2, and 4–7. Paper 19 (“Mot.”). We grant the motion. This proceeding is therefore limited to the patentability of claims 3 and 8–19 (“challenged claims”).” slip op. at 2

    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Patent Owner proposes a slightly different level of ordinary skill, arguing that a bachelor’s degree, not a master’s degree, is all that is required because that is the “target audience for the ’886 Patent.” PO Resp. 11. Patent Owner does not otherwise dispute Petitioner’s proposed level of skill. Id. We used Petitioner’s proposed definition in the Institution Decision. Inst. Dec. 13. Neither party argues any issue as dependent on the level of ordinary skill or the differences between the proposals. Accordingly, the issues here are not dependent on the level of ordinary skill and the result is the same regardless of which definition is adopted. On this record, there is no reason to change from Petitioner’s definition used in the Institution Decision.” slip op. at 7

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

      “transistors” as a term that might require construction during trial. Inst. Dec. 17–18. At the hearing, the Petitioner argued that “cascaded transistors” means “[ar]ranged in a series of or in succession of stages so that each stage derives from or acts upon the product of the preceding [transistor]” and that there is no dispute that the limitation is taught by the prior art. Tr. 9:15–22. Patent Owner takes no position as to whether or not the prior art discloses “cascaded transistors.” Id. at 33:13–21 (“For the remainder of this proceeding, post institution, we have not taken any position regarding the scope of the cascaded transistors or the disclosure of the cascaded transistors in any of the prior art. We have not disputed that.”). Because Patent Owner takes no position on the issue, there is no dispute that “cascaded transistors” are shown in the prior art, construction is not necessary. Realtime, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. original)). 2. “isolated island” Patent Owner disputes Petitioner’s contention that the prior art teaches or suggests claim 3’s recitation of “said plurality of cascaded transistors is situated within an isolated island.” Pet. 35–36; PO Resp. 16–17. Although the parties dispute whether an “isolated island” is shown in the prior art, neither party proposes a construction for the term “isolated island.” We agree that the arguments presented do not require construction of “isolated island.” The issues can be determined on the plain meaning of the term in view of the arguments made. See Section II.D below.” slip op. at 8

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successAnalogous artMotivation foundUnpatentable

      “We find that Petitioner has sufficiently shown Yu is analogous art to Okashita. Both references are directed to the manufacture of semiconductors, which we find to be the field of endeavor. Ex. 1004, 1:47– 58; Ex. 1005, 1:16–26. More specifically, we agree with Petitioner and find that both references are in the same field of endeavor because they relate to SOI configuration. Pet. Reply 6 (citing Pet. 7–8, 39–40; Ex. 1002 ¶¶ 77–80, 90–91). Because we find the references relied upon are in the same field of endeavor, we need not reach whether they are reasonably pertinent to the problem faced by the inventor. We also find that Petitioner has shown rational underpinnings for combining Okashita and Yu. Pet. 43–44. That the references have differences is not the test. Rather, the test is whether a person of ordinary skill in the art would have had motivation to combine them. We find there is sufficient motivation. Id. at 43 (citing Ex. 1005, 2:4–17; Ex. 1002 ¶¶ 177– 178). 3. Conclusion on Ground 3 Patent Owner does not argue any other reason that Ground 3 has not been sufficiently shown. Based on the full record, we determine that Okashita and Yu teach or suggest all the limitations of claim 3 and that one of ordinary skill in the art would have combined the references in the manner asserted with a reasonable expectation of success. We thus determine that Petitioner has established by a preponderance of the evidence that claim 3 would have been obvious over the combination of Okashita and Yu.” slip op. at 21

    Patent outcomesUS 7,745,886 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 7,745,886
  • PTAB · Mar 13, 2026 · IPR2024-01219 · APJ Avelyn M Ross · IPR · Final written decision

    Claims 1–11 are unpatentable as obvious over the Richardson-based grounds; the Yu and Paparrizos grounds do not establish unpatentability.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Petitioner contends that a person of ordinary skill in the art, “[a]s of the claimed priority date of July 3, 2014, . . . would have been a person with a bachelor’s degree in electrical engineering or its equivalent and two years of experience in the field of electrical engineering including some experience in design of battery charging systems.” Pet. 21 (citing Ex. 1003 ¶¶ 19–30). Patent Owner “does not propose a different level of skill in the art[.]” PO Resp. 16. In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art, because it is supported by the testimony of C. Arthur MacCarley and not disputed by Patent Owner.” slip op. at 11

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

      “Petitioner submits there are no formal claim constructions necessary in this proceeding[.]” Pet. 22. Patent Owner also “does not propose any terms need to be construed.” PO Resp. 15. As neither party proposes an express construction for our consideration and because we determine that claim construction is not necessary, we do not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co. Matal, 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review). slip op. at 11

    • PTAB / AIA Trials › §315(e) estoppelNot reached

      “arguments relating to whether the prior findings are “necessary to the determination” or whether estoppel applies to arguments relating to Richardson being inoperative. See Pet. Reply 27. Nor does Petitioner respond to our inquiry about whether collateral estoppel maybe applied on a limitation by limitation basis. See Pet. Reply 27. At the hearing, however, Petitioner confirmed that resolution of the issue is not necessary to our final determination. JUDGE ROSS: Do we even need to decide the collateral estoppel issue? I mean, it seems to me that if your petition clearly made out your case for the combination of Richardson and Zhao, then we don't even need to reach that. MR. CHANDRA: That’s exactly right, Your Honor. That is our position, as well. We believe collateral estoppel applies, but you don't need to decide that issue in order to find these claims unpatentable. As I mentioned before, these are the same references. We have fairly sought out all of the portions of Richardson, we cited to specific portions. Not just relying on collateral estoppel, but the teachings of the reference itself. So, while this is an issue, we believe that collateral estoppel should apply. It does not have to apply in order to find the challenged claims unpatentable. Tr. 19:9–20. We are persuaded, as discussed in Section II.G., that Petitioner has shown where Richardson in combination with Zhao meets each limitation of the claims of the ’203 patent. Accordingly, we need not address whether Petitioner has demonstrated sufficiently that collateral estoppel applies here.” slip op. at 14

    • BurdenDecided for patent owner

      “With respect to Petitioner’s allegations that rest on AAPA, we determine Petitioner has failed to show that claims 2, 10, and 11 are unpatentable. Our rules require that a petition for inter partes review must base the asserted challenges on “prior art consisting of patents or printed publications.” 35 U.S.C. § 311(b); 37 C.F.R. § 42.104(b)(2) and (4). And, a petitioner who relies on applicant admitted prior art as the basis, or part of the basis, of a ground, runs afoul of § 311. Qualcomm, 134 F.4th at 1365; see also USPTO Memorandum, Enforcement and Non-Waiver of 37 C.F.R. § 42.104(b)(4) and Permissible Uses of General Knowledge in Inter Partes Reviews (Jul. 21, 2025), available at www.uspto.gov/sites/default/ files/documents/aapa_memo_final__signed.pdf. We acknowledge but reject Petitioner’s position that its combinations discussing AAPA do not “rely” on AAPA but rather rely on U.S. Patent No. 5,793,185 (“the ’185 patent”), described in the ’203 patent as prior art. Pet. Reply 26. A petition for inter partes review must identify, “in writing and with particularity, each claim challenged, the grounds on which the challenge to each claim is based, and the evidence that supports the grounds for the challenge to each claim.” 35 U.S.C. § 312(a)(3); 37 C.F.R. § 42.104 (b)(4). Here, Petitioner’s contention that the Grounds 2 and 5 actually rely on the ’185 patent when discussing AAPA is inconsistent with the Petition. In particular, the Petition does not cite to or direct our attention to any specific details from the ’185 patent to support its challenges. See generally Pet. 54–57, 76–77. Accordingly, Petitioner has failed to show, by a preponderance of the evidence, that claims 2, 10, and 11 would have been unpatentable over the combination of Richardson, Zhao, and AAPA as well as over the combination of Yu, Paparrizos, and AAPA. Petitioner’s alternative allegations based on Epower-20/Epower-21 are considered below.” slip op. at 18

    Patent outcomesUS 11,667,203 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 11,667,203
  • PTAB · Mar 13, 2026 · IPR2024-01405 · APJ Arthur M Peslak · IPR · Final written decision

    Claims 1–20 are unpatentable: claims 1–20 over Torii, claims 1–3, 9, 11–13, and 19 over Ide, and claims 1–7, 10–17, and 20 over Gambino with Conn, with Ding for claims 10 and 20.

    RulingsFinal written decision
    • Expert testimonyPetitioner expert discountedDecided for patent owner

      “of the substrate is based on Dr. Thompson’s testimony. In his first declaration, Dr. Thompson relies on Conn’s paragraphs 31 and 35 to support the annotated version of Figure 2 in the Petition. Ex. 1003 ¶¶ 83–84. As discussed above, paragraphs 31 and 35 do not disclose that the anchor vias 14 are located in the corner of the substrate. The second annotated Figure 2 shown in Petitioner’s Reply does not appear in either of Dr. Thompson’s declarations (See Ex. 1003, Ex. 1034). It appears to be mere attorney argument not evidence. Dr. Thompson testified in his deposition that the second annotated version is based on his interpretation of Conn. Ex. 2009, 45:2–46:9. Because Dr. Thompson’s testimony is not adequately supported by the disclosure of Conn, we find that his testimony on the point of whether Conn discloses anchor vias located in the corner of the substrate is entitled to little, if any, weight. 37 C.F.R. § 42.65(a) (“Expert testimony that does not disclose the underlying facts or data on which the opinion is based is entitled to little or no weight.”). Therefore, because Petitioner has the burden of proof, we find that Petitioner has not shown that Conn discloses this limitation.” slip op. at 27

    • ExcludeMotion to exclude, deniedDenied

      “J. Petitioner’s Motion to Exclude Petitioner moves to exclude Exhibits 2007 and 2008. MTE, 1. Petitioner argues that the Exhibits are in violation of FRE 401, 402, 403, and 901. Id. We do not rely on either Exhibit 2007 or 2008 in this Decision. Consequently, we deny Petitioner’s MTE as moot.” slip op. at 72

    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “We agree with Petitioner that the differences between the parties’ proposed levels of skill in the art are immaterial for the purposes of this Decision. We apply Petitioner’s proposed level of skill in the art because it appears consistent with the problems addressed in the ’826 patent and the prior art. Further, our determination in this case would not be affected if we were to adopt Patent Owner’s proposed level of skill in the art.” slip op. at 11

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

      “Claim 1 uses the term “comprising” which is open-ended and normally does not exclude additional, unrecited elements. See Mars Inc. v. H.J. Heinz Co., 377 F.3d 1369, 1376 (Fed. Cir. 2004). This is in contrast to the phrase “consisting of.” See Multilayer Stretch Cling Film Holdings, Inc. v. Berry Plastics Corp., 831 F.3d 1350, 1358 (Fed. Cir. 2016) (there is an “exceptionally strong presumption that a claim term set off with ‘consisting of’ is closed to unrecited elements.”). The use of comprising in claim 1, thus, weighs against a construction limiting claim 1 to direct contact between the backside metal layer and the bottom surface of the semiconductor substrate. Additionally, we note that claim 1 does not recite that the backside metal layer is “directly on” or “formed on” the bottom surface or similar language that would suggest “direct contact” may be required. For these reasons, we determine that the language of claim 1 does not support Patent Owner’s proposed construction.” slip op. at 17

    Patent outcomesUS 9,245,826 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 9,245,826
  • PTAB · Mar 11, 2026 · IPR2024-01404 · APJ Hyun J Jung · IPR · Final written decision

    Claims 1–18 are unpatentable: claims 1–6, 9–14, 17, and 18 as anticipated by Cooney and obvious over Cooney; claims 7 and 15 over Cooney and Dean; claims 8 and 16 over Cooney and Farooq or …

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Based on the full record, we maintain and affirm that a person of ordinary skill in the art “would have had at least a master’s degree in electrical engineering or a similar field and at least two years of experience working with semiconductor systems” and that “[a]dditional relevant work experience can compensate for less education, and vice versa.” Pet. 9–10 (citing Ex. 1002 ¶¶ 72–74). We agree with the parties that any differences in the parties’ proposed level of ordinary skill would not affect our analysis. Pet. Reply 1; Tr. 25:4–9 (Patent Owner’s counsel agreeing that any differences in the parties’ proposed level of ordinary skill in the art are immaterial). We also find that Petitioner’s proposed level of ordinary skill in the art is consistent with the ’609 patent and the asserted prior art.” slip op. at 9

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

      “Based on the full record and because Petitioner’s anticipation challenge is based on giving these recitations no patentable weight and Petitioner’s obviousness challenge is based on the same recitations having patentable weight, we determine that resolving whether to give patentable weight to the recitations “to reduce thermal stress in said semiconductor substrate,” “to provide space for said conductive filler to expand inward,” and “to prevent contamination during processing of said semiconductor substrate” is not necessary to resolve the parties’ dispute. Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms that . . . are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. full record, we also determine that express claim interpretation of any other claim term is not necessary. Id.” slip op. at 10

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

      “the claim, must be found in a single prior art reference. Net MoneyIN, Inc. v. VeriSign, Inc., 545 F.3d 1359, 1369 (Fed. Cir. 2008); Karsten Mfg. Corp. v. Cleveland Golf Co., 242 F.3d 1376, 1383 (Fed. Cir. 2001). Each element of the challenged claim must be found, either expressly or inherently, in the single prior art reference. Verdegaal Bros., Inc. v. Union Oil Co. of Cal., 814 F.2d 628, 631 (Fed. Cir. 1987). When evaluating a prior art reference in the context of anticipation, the reference must be “considered together with the knowledge of one of ordinary skill in the pertinent art.” In re Paulsen, 30 F.3d 1475, 1480 (Fed. Cir. 1994) (citing In re Samour, 571 F.2d 559, 562 (CCPA 1978)). “[A] reference can anticipate a claim even if it ‘d[oes] not expressly spell out’ all the limitations arranged or combined as in the claim, if a person of skill in the art, reading the reference, would ‘at once envisage’ the claimed arrangement or combination.” Kennametal, Inc. v. Ingersoll Cutting Tool Co., 780 F.3d 1376, 1381 (Fed. Cir. 2015) (quoting In re Petering, 301 F.2d 676, 681 (CCPA 1962)).” slip op. at 7

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner

      “find that Cooney discloses “silicon vias having a hollow center.” Ex. 1002 ¶¶ 120–123; Ex. 1004 ¶¶ 55, 60, Fig. 6. We also find that the portions of Pogge cited by Petitioner show that its “void 25 has an important function in relieving stresses caused by differences in the thermal coefficient of expansion (TCE) of the various materials in and around the feature” (Ex. 1005 ¶ 27) and that the portions of Edelstein cited by Petitioner show that, “[a]lthough it does not change the thermal expansion coefficient, the introduction of a void or voids reduces the effective modulus and Poisson ratio of the through-via, resulting in a compliant through-via that exerts much less stress and force on the surrounding structures” (Ex. 1006 ¶ 47). As discussed above, we find that Cooney’s void 25 is “entirely surrounded by” its conductive filler 24 that, in turn, is surrounded by liner 22 and substrate 10’. Ex. 1004, Fig. 6. We credit Petitioner’s relied-upon testimonial evidence that the presence of a void was known to reduce thermal stress in the surrounding substrate, because the citations to the record support it. Ex. 1002 ¶¶ 124–134; Ex. 1005 ¶¶ 1, 9, 25–28, Fig. 2D; that “a void can decrease thermal stress in the substrate”). We agree with Petitioner’s declarant that Pogge provides a void in a TSV similar to Cooney and the ’609 patent. Ex. 1001, Fig. 4; Ex. 1002 ¶ 127; Ex. 1004, Fig. 6; Ex. 1005, Fig. 2D. We, thus, credit the testimony that, because of their common structural arrangements, one of ordinary skill in the art would have understood that stress-relieving characteristics in Pogge would have been manifested in Cooney’s void. Ex. 1002 ¶ 127. We also agree with Petitioner’s declarant that Edelstein includes a void in a TSV similar to Cooney, the ’609 patent, and Pogge. Ex. 1001, Fig. 4; Ex. 1002 ¶ 130; Ex. 1004, Fig. 6; Ex. 1005, Fig. 2F; Ex. 1006, Fig. 6F. We, therefore, credit the testimony that, because of their common structural arrangements, one of ordinary skill in the art would have understood that stress-relieving characteristics in Edelstein would have also been manifested in Cooney’s void. Ex. 1002 ¶ 130.” slip op. at 33

    Patent outcomesUS 9,147,609 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 9,147,609
  • PTAB · Mar 4, 2026 · IPR2024-01222 · APJ Garth D Baer · IPR · Final written decision

    Claims 34–37 and 40–46 are unpatentable as obvious over the Yamazaki-based and Weaver-based grounds.

    RulingsFinal written decision
    • Novelty / Anticipation (§102) › Priority / effective filing date / continuation supportDecided for petitioner

      “Patent Owner bears the burden of production to establish that its claimed invention is entitled to an earlier priority date for this fact-intensive issue. See In re Magnum Oil Tools Int’l, Ltd., 829 F.3d 1364, 1375–76 (Fed. Cir. 2016). We agree with Petitioner that the email chain does not support Patent Owner’s conception claim because it “does not discuss depositing a planarization layer, as required by both independent claims.” Pet. Reply 3. Patent Owner asserts that the inventor’s discussion of “PML” (polymer multi-layer) encapsulation in the email chain shows their conception of the claimed planarization layer because the ’389 patent describes that PMLs “‘[t]ypically’ include[e] ‘a planarization layer’ that ‘is provided to give a planar surface’ for deposition of an upper layer,” and “‘address ‘any point defects (i.e. pin holes)’ that might appear in the barrier layer’s surface.” PO Resp. 6 (quoting Ex. 1001, 1:31–37, 1:41–44, 1:56–62). We disagree with Patent Owner for two reasons. First, the challenged patent’s specification does not corroborate that the inventors conceived the claimed planarization before the challenged patent’s priority because it did not exist at the time of the email. Whether the inventors, at the time of filing, considered PMLs to typically include a planarization layer as of the claimed priority date does not support the allegation that they conceived of that same planarization layer more than a year earlier. Moreover, the ’389 patent’s teaching that “[t]ypically, for PML structures, a planarization layer 106 is formed” (Ex. 1001, 1:30–31) shows that the inventors recognized PML structures and planarization layers were distinct because only a subset of PML structures formed planarization layers, even if they do so typically. Thus, the inventor’s discussion of a PML layer in the email chain does not evidence their conception of the claimed planarization layer, as Patent Owner contends. Additionally, even if we were to understand the inventors’ mention of PML encapsulation in the emails, together with the discussion of patterning techniques for an organic layer, as discussing a planarization layer, such discussions are evidence of brainstorming ideas, rather than documenting the path taken with the claimed invention. For instance, the inventors use phrases like “don’t know if this will work,” “these are all just ‘undeveloped’ ideas,” and “looking forward to keep this discussion rolling.” Ex. 2006, 1; see also Ex. 1034, 59:22−59:18. As Petitioner argues, and we agree, these are more theoretical and future-development discussions than an exchange of a definite idea. Pet. Reply 2−3 (citing Hybritech Inc. v. Monoclonal Antibodies, Inc., 802 F.2d 1367, 1376 (Fed. Cir. 1986). For these reasons, we agree with Petitioner that Patent Owner has not” slip op. at 6

    • Novelty / Anticipation (§102) › Prior-art status of a reference › Applicant-admitted prior artDecided for petitioner

      “B. Whether Petitioner Relies on Applicant Admitted Prior Art Patent Owner asserts we should “not consider” Yamazaki-based challenges because Petitioner included Applicant Admitted Prior Art (AAPA) in those grounds. See PO Resp. 16 (citing Qualcomm Incorporated v. Apple Inc., 134 F.4th 1355 (Fed. Cir. 2025)) (holding that AAPA may not be part of the basis for an inter partes review). We disagree. As Petitioner notes, it “utilizes the AAPA in the alternative with Ghosh, to show that it was known to manufacture OLED devices in bulk (which [Patent Owner] does not dispute).” Pet. Reply 9. Because “[t]he Petition identifies disclosures in Ghosh that independently demonstrate the same teachings for which the AAPA is cited,” we agree with Petitioner that it does not improperly rely on AAPA for any of its challenges. Id.” slip op. at 8

    • Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication establishedDecided for petitioner

      “C. Whether Yamazaki, Weaver, and Palanisamy Are Printed Publications under 35 U.S.C. § 311(b) Patent Owner asserts that Yamazaki, Weaver, and Palanisamy do not qualify as printed publications under 35 U.S.C. § 311(b) because they only qualify as prior art under § 102(e). PO Resp. 17. According to Patent Owner, “[e]ven though the Federal Circuit has held that such references are ‘printed publications’ under 311(b), to preserve arguments on appeal, Patent Owner submits that such an interpretation is inconsistent with the plain statutory language, the precedent, and non-public accessibility of an unpublished patent application.” Id. We disagree with this argument because the Federal Circuit has rejected it, as Patent Owner acknowledges. See Lynk Labs, Inc. v. Samsung Electronics Co., 2023-2346, Slip. Op. (Fed. Cir. Jan. 14, 2025).” slip op. at 8

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

      “Yamazaki does not involve multiple devices on a substrate” and Ghosh teaches “non-selective deposition of at least the barrier layer.” PO Resp. 31. We disagree with this argument because it attacks Yamazaki and Ghosh individually, rather than the combination of Yamazaki’s selective deposition and Ghosh’s plurality of devices that Petitioner asserts. See In re Keller, 642 F.2d 413, 426 (CCPA 1981). We also disagree with Patent Owner’s criticism that Petitioner fails to explain why skilled artisans would have ignored Ghosh’s non-selective deposition method for barrier layers on multiple devices. PO Resp. 32. This argument attacks a straw man as Petitioner does not propose modifying Ghosh’s method with Yamazaki’s selective deposition. See Pet. 21–23. Rather, Petitioner proposes modifying Yamazaki’s selective deposition method by applying it to Ghosh’s teaching of encapsulating a plurality of OLED devices. Id. Next, Patent Owner asserts that skilled artisans would not have extended Yamazaki’s single-device fabrication/encapsulation method to a plurality of devices on a substrate because doing so would “multiply defects and errors, drop the yield exponentially, and increase the cost.” PO Resp. 34. Patent Owner asserts that precision/defect problems would be particularly acute when using Yamazaki’s inkjet method to print devices’ electro luminescence layers. Id. at 35–36. We disagree. Even if extending Yamazaki’s method to Ghosh’s multiple devices comes at a cost of potential defects, that tradeoff would not undermine Petitioner’s proffered combination given Petitioner’s articulated benefits outline above, including facilitating manufacturing display panels for OLEDs with improved throughput, improved productivity, and reduced manufacturing costs, as compared to fabricating/encapsulating just a single device. See Winner Int’l Royalty Corp. v. Wang, 202 F.3d 1340, 1349 n.8 (Fed. Cir. 2000) (“The fact that the motivating benefit comes at the expense of another benefit, however, should not nullify its use as a basis to modify the disclosure of one reference with the teachings of another.”). It also does not matter that “inkjet printing yielded devices of half the efficiency than spin coating,” as Patent Owner asserts (PO Resp. 35), because Petitioner does not need to show that Yamazaki’s inkjet printing would be the best option for batch fabrication/encapsulation, only that it would was a suitable one from which the prior art did not teach away. See Par Pharm., Inc. v. TWi Pharms., Inc., 773 F. 3d 1186, 1197–98 (Fed. Cir 2014). That is, Petitioner does not need to show that Yamazaki’s inkjet method was an improvement over other known fabrication/encapsulation methods, so long as it was a known fabrication/encapsulation method and skilled artisans would understand that implementing it for a plurality of devices had known advantages over fabricating/encapsulating a single device, which Petitioner identifies. See Pet. 22. We also agree with Dr. Subramanian that skilled artisans would have a reasonable expectation of success in making the proposed combination given similarities between the references (both are directed to encapsulation of an OLED display device with multiple thin-film layers and at least the first encapsulation is selectively deposited) and because “as the ’389 patent admits, in the prior art it was conventional to use batch fabrication to manufacture OLED display devices with thin-film encapsulation.” Ex. 1003 ¶ 86. As Dr. Subramanian explains, a particular advantage of inkjet printing is that it scales well to larger areas and it was known at the time of the ’389 patent that inkjet could be used to print multiple devices on a glass substrate. Ex. 1032 ¶¶ 2, 27–28. Patent Owner’s argument that “Yamazaki’s methods are far from ready for manufacturing” (PO Resp. 34) goes well beyond what is necessary to show that skilled artisans would have had a reasonable expectation of achieving what is claimed. See Intelligent Bio-Sys., Inc. v. Illumina Cambridge Ltd., 821 F.3d 1359, 1367 (Fed. Cir. 2016). Given Petitioner’s analysis outlined above, we agree with Petitioner that it would have been obvious to skilled artisans to fabricate and encapsulate multiple OLED devices on a substrate using Yamazaki’s ink-jet methods. slip op. at 15

    Patent outcomesUS 6,949,389 unpatentable
    § 102 anticipation§ 103 obviousnesscites KSR
    Patents in suitUS 6,949,389
  • PTAB · Feb 24, 2026 · IPR2024-01203 · APJ Avelyn M Ross · IPR · Final written decision

    Claims 1–11 are unpatentable as obvious; claim 12 was not shown unpatentable because the evidence did not establish that Froitzheim’s silver contact was formed over silicon dioxide.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Petitioner contends that a person of ordinary skill in the art would have had (i) an advanced degree in electrical engineering, mechanical engineering, applied physics, chemistry, materials science, or a related discipline and (ii) at least one year of experience 7 Neither Petitioner nor Patent Owner raises issues of objective indicia of nonobviousness. designing, developing, or researching the design and/or manufacture of solar cells or related technologies. Alternatively, a POSITA [i.e., a person of ordinary skill in the art] would have had (i) a bachelor’s degree in the aforementioned disciplines and (ii) at least two years of experience designing, developing, or researching the design and/or manufacture of solar cells or related technologies. Less work experience may be compensated by a higher level of education, and vice versa.” slip op. at 8

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

      “C. Claim Construction We construe claim terms according to the standard set forth in Phillips v. AWH Corp., 415 F.3d 1303, 1312–17 (Fed. Cir. 2005) (en banc); 37 C.F.R. § 42.100(b). Under Phillips, we give claim terms “their ordinary and customary meaning.” Phillips, 415 F.3d at 1312. “[T]he ordinary and customary meaning of a claim term is the meaning that the term would have to a person of ordinary skill in the art in question at the time of the invention.” Id. at 1313. “Importantly, the person of ordinary skill in the art is deemed to read the claim term not only in the context of the particular claim in which the disputed term appears, but in the context of the entire patent, including the specification.” Id.” slip op. at 9

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

      “We are persuaded that Petitioner has shown a reasonable expectation of success in the combination of Froitzheim and Gan. Petitioner explains that the combination of Froitzheim and Gan simply replaces one emitter, i.e., Froitzheim’s diffused emitter, with the polysilicon emitter of Gan. Pet. 36. According to Petitioner, a person of ordinary skill in the art would have also readily understood how to replace a diffused emitter with a polysilicon emitter and oxide layer [and] would have understood that instead of diffusing boron into the substrate’s back side as taught by Froitzheim, a [person of ordinary skill in the art] would instead follow the manufacturing technique taught by Gan. Pet. 37 (citing Ex. 1005, 246). Petitioner explains that the Gan processes are well-known and routine, and Dr. Holman states that “modifying Froitzheim in view of Gan simply involves using Gan’s known technique of a polysilicon emitter and oxide layer with Froitzheim’s known solar cell to improve Froitzheim’s solar cell in a similar way.” Pet. 37 (citing Ex. 1003 ¶ 144). For example, Petitioner directs our attention to “multiple instances” in which oxide layers and polysilicon emitters have been implemented successfully in the art. Pet. 37 (citing Ex. 1005, 246; Ex. 1006 ¶ 22; Ex. 1046, Abstr., 1121; Ex. 1003 ¶ 145). Furthermore, Gan’s statement that “cell performance can be improved if the diffused-emitter is replaced with the polysilicon emitter” and “polysilicon emitters with low J0 and ρc can be obtained with a very small fraction of interfacial oxide breakup” indicate a reasonable expectation of success. Ex. 1005, 245, 249. Gan also states that “polysilicon emitters with these qualities can be quite useful for silicon concentrator solar cells.” Ex. 1005, 249. Thus, we are persuaded that Petitioner has demonstrated that a person of ordinary skill in the art would have had a reasonable expectation of success in combining Froitzheim and Gan.” slip op. at 17

    • Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner

      “We are not persuaded the record evidence rises to the level of a teaching away. “A reference may be said to teach away when a person of ordinary skill, upon reading the reference, would be discouraged from following the path set out in the reference, or would be led in a direction divergent from the path that was taken by the applicant.” In re Gurley, 27 F.3d 551, 553 (Fed. Cir. 1994). And “teaching away” requires more than the mere expression of a general preference.” Galderma Labs., L.P., v. Tolmar, Inc., 737 F.3d 731, 738 (Fed. Cir. 2013). Notably, our reviewing court has determined that a reference can distinguish prior art in order to show the novelty of an invention without teaching away from combining the prior art with the invention disclosed in the reference. See Ricoh Co. v. Quanta Computer Inc., 550 F.3d 1325, 1332 (Fed. Cir. 2008). Here, Li prefers a “heterogeneous PN junction” and states that “a PN junction is prepared by a low-temperature deposition method, which avoids a conventional diffusion process at 800–1000°C. Such high-temperature process will cause more defects or contamination in silicon material, which will affect the improvement of cell efficiency.” Ex. 1008, 4. But, Li’s preference for lower temperature diffusion processes does not amount to a teaching away from the broader disclosure. In fact, Li acknowledges that “[t]he silicon thin film can be prepared by any deposition method,” including conventional processes at higher temperatures. Ex. 1008, 4 (emphasis added). And, while Patent Owner asserts that “[d]eposition methods are not relevant to the parties’ dispute, which is over deposition temperature” (Sur-reply 17), the deposition method employed includes its deposition temperature. See Ex. 1008, 4 (Li describing “conventional” diffusion processes at temperatures of 800–1000° C). Thus, just because Li teaches one way of depositing its silicon thin film using a low-temperature deposition method does not mean that Li teaches away from high-temperature processes. Li’s teachings do not discredit or discourage high-temperature processes in a manner that may be said to teach away.” slip op. at 51

    Patent outcomesUS 8,222,516 mixed
    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 8,222,516
  • Nxtgen Toys, LLC v. Zipstring, LLCAll claims unpatentable
    PTAB · Feb 20, 2026 · IPR2024-01213 · APJ Richard H Marschall · IPR · Final written decision

    Claims 1–4, 12, and 15–17 are unpatentable; substitute claim 27 is allowed, while substitute claims 21–26 and 28 are denied as obvious.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Petitioner contends that a person having ordinary skill in the art at the time of the invention “was typically a person with a bachelor’s degree in mechanical engineering, aerospace engineering, physics, or other science or 6 Patent Owner does not rely on any objective indicia of nonobviousness in this proceeding. engineering based degree that [was] familiar with general principles of mechanics and aerodynamics with at least two years of experience in product design and development in the field of toys or other amusement type devices.” Pet. 32 (citing Ex. 1002 ¶¶ 2–6, 22–26). Patent Owner states that it submitted the following proposal for a POSITA in the related district court litigation: “[a POSITA] would have had at least a B.S. degree in Mechanical Engineering, Electrical Engineering, Aerospace Engineering, Industrial Design, Product Design, or similar field, with at least two years industry experience in one of these fields, and such POSITA would have been familiar with general principles of mechanics, fluid mechanics and aerodynamics.” PO Resp. 4–5. We note that the parties’ proposals overlap considerably, and neither party argues the inadequacy of the other party’s proposal or that any patentability issue in this case turns on the resolution of this issue. We find Petitioner’s definition consistent with the problems and solutions disclosed in the ’774 patent and prior art of record, and adopt it as our own. See, e.g., GPAC, 57 F.3d at 1579 (approving the determination of the level of ordinary skill in the art by appeal to the references of record). We would arrive at the same findings and conclusions in this Decision if we adopted Patent Owner’s proposal.” slip op. at 7

    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

      “Id. at 1312–13. Only terms in controversy need be construed, and only to the extent necessary to resolve the controversy. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). Petitioner contends that no “term requires construction to resolve the invalidity grounds presented in this Petition since the prior art renders claims 1–4, 12, and 15–17 unpatentable under any reasonable interpretation of the claims.” Pet. 7. Patent Owner argues that it “does not believe express claim constructions are necessary during this proceeding because the claims can readily be given their ordinary and customary meaning in the context of the patent at the time it was filed.” PO Resp. 5. Based on the parties’ positions and our view of the record, we need not expressly construe any claim limitations to resolve the issues in this Decision. To the extent that any implicit claim construction issues relate to the issues raised by the parties, we address them in the context of the parties’ patentability arguments below.” slip op. at 9

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentableUnpatentable

      “string, and that adding Scorch’s slot removes this arguably inconvenient process by allowing insertion and removal of a string without removing and reinstalling any aspects of the housing. See Pet 85–86 (citing Ex. 1002 ¶¶ 174–175; Ex. 1007, 3:30–3:53, 6:03; Ex. 1008, 3:46–4:45); Pet. Reply 18–20 (citing in part Ex. 2002 ¶ 187 (Dr. Janét’s testimony that Wagner’s removal and reinstallation of a cover “may be viewed as an inconvenient process”)). Making insertion and removal of the string easier and quicker provides a notable advantage over Wagner’s existing device. See id. Scorch itself supports this argument and the related expert testimony because it discusses insertion and removal of strings and stated that the slot allows a user to “swap them out really quick.” Ex. 1007, 3:30–53. Petitioner also persuasively argues that a POSITA would know how to add the slot while maintaining the proper operation of the device, such as allowing insertion and removal of the string and avoiding inadvertent exiting of the string from the device. See Pet. 86–87 (citing Ex. 1002 ¶¶ 175–176; Ex. 1007, 4:00–30, Ex. 1008, 2:49–52); Pet. Reply 19, 21 (citing Ex. 1002 ¶¶ 174–176). We find Petitioner’s arguments and reasoning in support of adding Scorch’s slot to Wagner’s housing straightforward and persuasive. Patent Owner’s arguments against the combination do not directly refute Petitioner’s reasoning or cast doubt on Scorch’s statement that its slot enables “quick” insertion and removal of a string—quicker than Wagner’s method that requires removal and replacement of a cover on its housing. See PO Resp. 16–22; PO Sur-reply 14–20; Ex. 2002 ¶ 187 (acknowledging inconvenience of Wagner’s existing process for insertion and removal of a string). Patent Owner suggests that Petitioner’s proposed combination fails to take into consideration certain drawbacks such as the risk of inadvertent string exit from the housing or slot, but Petitioner expressly addresses such concerns in the Petition. See PO Resp. 18 (stating that Scorch’s slotted funnel may allow the string to “shoot out the slot” and that Scorch addresses this by adding “a bent wire” to “prevent the string from coming out the side”); PO Sur-reply 16–17; Pet. 86–87 (arguing that Wagner’s flanges would help to trap the string in place, but if not, Scorch’s additional structures could be used to restring the string and “to further reduce the risk of a string inadvertently exiting” the device). We agree with Petitioner that a POSITA would understand how to incorporate Scorch’s slot without causing inadvertent removal of the string—using structures already present in Wagner and Scorch—and the need to add such unclaimed structurers does not teach away from the combination as Patent Owner suggests. See Pet. 86–87; PO Resp. 22. We also agree with Petitioner that a POSITA would understand how to make minor modifications, if necessary, to allow insertion and removal of the string around Wagner’s flanges. See Pet. Reply 21 (citing Ex. 1002 ¶¶ 174–176).” slip op. at 26

    • Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner

      “refute Petitioner’s reasoning or cast doubt on Scorch’s statement that its slot enables “quick” insertion and removal of a string—quicker than Wagner’s method that requires removal and replacement of a cover on its housing. See PO Resp. 16–22; PO Sur-reply 14–20; Ex. 2002 ¶ 187 (acknowledging inconvenience of Wagner’s existing process for insertion and removal of a string). Patent Owner suggests that Petitioner’s proposed combination fails to take into consideration certain drawbacks such as the risk of inadvertent string exit from the housing or slot, but Petitioner expressly addresses such concerns in the Petition. See PO Resp. 18 (stating that Scorch’s slotted funnel may allow the string to “shoot out the slot” and that Scorch addresses this by adding “a bent wire” to “prevent the string from coming out the side”); PO Sur-reply 16–17; Pet. 86–87 (arguing that Wagner’s flanges would help to trap the string in place, but if not, Scorch’s additional structures could be used to restring the string and “to further reduce the risk of a string inadvertently exiting” the device). We agree with Petitioner that a POSITA would understand how to incorporate Scorch’s slot without causing inadvertent removal of the string—using structures already present in Wagner and Scorch—and the need to add such unclaimed structurers does not teach away from the combination as Patent Owner suggests. See Pet. 86–87; PO Resp. 22. We also agree with Petitioner that a POSITA would understand how to make minor modifications, if necessary, to allow insertion and removal of the string around Wagner’s flanges. See Pet. Reply 21 (citing Ex. 1002 ¶¶ 174–176). At best, Patent Owner’s arguments on this issue establish potential drawbacks in Petitioner’s proposed combination, but drawbacks alone do not defeat Petitioner’s obviousness rationale that includes readily apparent benefits. See Winner Int’l Royalty Corp. v. Wang, 202 F.3d 1340, 1349 n.8 (Fed. Cir. 2000) (“The fact that the motivating benefit comes at the expense of another benefit . . . should not nullify its use as a basis to modify the disclosure of one reference with the teachings of another.”); Medichem, S.A. v. Rolabo, S.L., 437 F.3d 1157, 1165 (Fed. Cir. 2006) (“a given course of action often has simultaneous advantages and disadvantages, and this does not necessarily obviate motivation to combine “). In addition, even if Patent Owner were correct that Wagner’s existing design works as well as Petitioner’s proposed combination, given all of the tradeoffs involved, that would not fatally undermine Petitioner’s showing. In re Fulton, 391 F.3d 1195, 1200 (Fed. Cir. 2004) (obviousness does not require that the proposed combination “is the preferred, or most desirable, combination”). On this record, Petitioner’s (and Scorch’s) stated advantages that are achieved when adding Scorch’s slot to Wagner’s housing adequately support Petitioner’s motivation to combine rationale.” slip op. at 26

    Patent outcomesUS 11,674,774 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · KSR · Nautilus
    Patents in suitUS 11,674,774
  • PTAB · Feb 19, 2026 · IPR2024-01259 · APJ Kristen L Droesch · IPR · Final written decision

    Claims 1, 2, 4–7, and 9–15 are unpatentable; claims 3 and 8 are not shown unpatentable, principally because the Petition lacked a sufficient motivation to combine Inoue and Smith.

    RulingsFinal written decision
    • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

      “We do not agree with Patent Owner’s argument because it advocates for the importation of functional limitations from the ’794 Patent Specification into the claims––namely the disclosure that the bypass circuit continues to conduct electricity, and keeps the remaining lights lit, even when one or more individual lighting elements in the series are burned out, missing, or defective. See PO Resp. 7–9. It is well settled that it is improper to read an extraneous limitation into a claim from the specification. See e.g., Commark Comm’s Inc. v. Harris Corp., 156 F.3d 1182, 1186 (Fed. Cir. 1998); E.I. du Pont de Nemours & Co. v. Phillips Petroleum Co., 849 F.2d 1430, 1433 (Fed. Cir. 1988). An extraneous limitation is “a limitation read into a claim from the specification wholly apart from any need to interpret what the patentee meant by particular words or phrases in the claim.” E.I. du Pont de Nemours, 849 F.2d at 1433. Moreover, the language that Patent Owner wishes to import into the claim from the Specification is functional language that describes the function of the resistor bypass circuit. As explained below in the section addressing the subsequent claim recitation “conducting current at all times across the light sources when current is flowing through the circuit regardless of whether the LED light source are conducting current therethrough,” functional language is evaluated in view of the applied prior art to determine whether it imparts additional structure to distinguish the claimed invention over the prior art. Accordingly, to the extent the preamble recitation is limiting, we need not provide an express construction for “[a] resistor bypass circuit for a series lighting circuit.”” slip op. at 7

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITADecided for patent owner

      “We understand the term “inherent resistance” to mean the resistance at a particular operating current or voltage across the LED light source. Neither party disputes our understanding of the term “inherent resistance.” See Dec. on Inst. 9–10; PO Resp. 7–9; Pet. Reply.” slip op. at 10

    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “bachelor’s degree in electrical engineering, physics, materials science, or a related discipline, and four years of practical experience in designing or fabricating LED lighting systems, including controlling and driving LEDs,” or alternatively “would have had a master’s degree and three years of experience, or a Ph.D. degree and two years of experience.” Ex. 1013, 31 ¶ 3; see also Pet. 18. Patent Owner does not dispute Petitioner’s proposed definition of a person of ordinary skill in the art for the purpose of institution. See PO Resp. 2. We adopt Petitioner’s definition of a person of ordinary skill in the art because it is consistent with the level of skill reflected by the ’794 Patent Specification and the asserted prior art.” slip op. at 11

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

      “We do not agree with Patent Owner’s arguments because, as explained above in Section II.A., we decline to import functional language into the claim from the Specification to construe the preamble recitation as requiring the function of “continu[ing] to conduct electricity and keeps the remaining lights lit, even when one more individual lighting elements in the series are out, loose, broken, missing/removed, or defective.” Having considered both parties’ arguments and corresponding cited supporting evidence, we are persuaded that Inoue discloses each of the limitations of claim 1. Based on the entire record, we determine Petitioner shows by a preponderance of the evidence that claim 1 is anticipated by Inoue. See Pet. 25–26.” slip op. at 14

    Patent outcomesUS 11,533,794 mixed
    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 11,533,794
  • PTAB · Feb 17, 2026 · IPR2024-01132 · APJ Kevin W Cherry · IPR · Final written decision

    Claims 1–7 are unpatentable: claims 1–3 and 5 are anticipated by Anzai, claim 4 is obvious over Anzai and Yamazaki, and claims 1–7 are obvious over Yamazaki and Anzai.

    RulingsFinal written decision
    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Petitioner describes a person of ordinary skill in the art (“POSITA” or “ordinarily skilled artisan”) at the time of the invention as having “a Bachelors’ degree in electrical engineering or a comparable field of study, plus approximately two to three years of professional experience with electronic and optoelectronic device design” and notes that “[a]dditional graduate education could substitute for professional experience, and significant experience in the field could substitute for formal education.” Pet. 5–6 (citing Ex. 1002, Neikirk Decl., ¶ 23). Patent Owner’s expert, Dr. Bretschneider testifies that In my opinion, the field of “electronic and optoelectronic device design” is too broad. A POSITA of the ’121, had at least a Bachelors’ degree in a field of engineering or physics and at least two to three years of professional experience related to the design and manufacture of the relevant aspects of flat panel displays. Additional relevant graduate education related [sic] could reduce but not eliminate the time requirement for professional experience. While Dr. Neikirk proposes a different definition of a POSITA, the differences do not have material effect on my opinions rendered below. Regardless of which definition of a POSITA were used, my conclusions would remain the same Ex. 2005, Bretschneider Decl., ¶ 39. We agree with and will apply Petitioner’s statement of the level of ordinary skill in the art. This level of ordinary skill is reflective of the education and experience that would have been required to understand the problems and solutions identified in the ’121 patent and the prior art. Okajima v. Bourdeau, 261 F.3d 1350 (Fed. Cir. 2001). We note that our conclusions would be the same even if we applied Patent Owner’s slightly narrower definition of a POSITA.” slip op. at 11

    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

      “We find these definitions to be of some help in construing this term. We find that the common thread is that a “passivation layer” is an insulating layer that provides protection from the environment to the layers below it. See Ex. 1012, 140; Ex. 1013, 542, Ex. 1014, 798; Ex. 2010, 3; Ex. 2013, 1. We find this construction to be most consistent with the broad claim language and the disclosure in the Specification. Although “tying up dangling bonds,” may be a mechanism by which some materials provide such protection, nothing in the Specification or the extrinsic evidence provided appears to require that. Also, while chemical protection may be one kind of protection none of the evidence suggests that is the only protection that is provided. Moreover, nothing in the Specification supports reading a chemical protection requirement into the construction. Thus, we decline to adopt that portion of Patent Owner’s construction. Instead, we construe passivation layer as “an insulating layer that provides protection from the environment to the layers below it.” We need not construe the term any further to resolve the parties’ dispute over this claim language. See Realtime, 912 F.3d at 1375.” slip op. at 19

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

      “constructions for “passivation layer” and “capping layer.” We find that Petitioner has presented sufficient evidence to show that Anzai discloses both a “passivation layer” and a “capping layer.” As we explained above, we have construed “passivation layer” to mean “an insulating layer that provides protection from the environment to the layers below it.” Petitioner has shown that “first planarization film 17” is an insulating layer. See Ex. 1002 ¶¶ 62–65. We further find that Petitioner has shown sufficiently that “first planarization film 17” is “formed over the entire surface for flattening, which will protect the semiconductor surface from the surrounding environment.” Id. ¶ 63. We have rejected Patent Owner’s contentions that the film must tie up “dangling bonds,” and instead determined that protecting the surface from the environment is sufficient. Thus, we find that Petitioner has shown by a preponderance of the evidence that Anzai discloses the “passivation layer” of claim 3. As we explained above, we have construed “capping layer” to be “an insulation layer covering (i.e., capping) an underlying layer or structure.” Here, Petitioner has shown that Anzai’s planarization film 19 meets the claimed “capping layer.” See Pet. 20. We find that Petitioner has shown that it is more likely than not that “planarization film 19” is made of insulating material. As Dr. Neikirk persuasively testifies, Anzai discloses that planarization layer 17 may be made of an organic resin for flattening the surface. EX1003, 4:20-24. While Anzai does not disclose the material for planarization layer 19, it must be made of an insulation material because in the embodiment of Fig. 3A, it is the sole layer between electrode layer 71 and cathode layer 65 forming the second capacitor. Id., 6:3–8; Fig. 3A. Moreover, Anzai discloses that the first planarization film 17 and the second planarization film 19 for the first embodiment “function as the capacitance insulating film for this configuration.” Id., 5:62–67. Ex. 1002, Neikirk Decl., ¶ 62. We find this testimony well-reasoned and entitled to substantial weight. We further agree with Dr. Neikirk that a “POSITA would further understand that the second planarization film 19 is then further disposed on the first planarization film 17 (capping the passivation layer).” Id. ¶ 63 (citing Ex. 1003, 5:3–13; Figs. 2A–B, 3A–B). Thus, we find that Petitioner has shown by a preponderance of the evidence that Anzai discloses the claimed “capping layer.” Accordingly, we find that Petitioner has shown by a preponderance of” slip op. at 32

    • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

      “motivation to combine Anzai and Yamazaki. See Pet. 25–27; Ex. 1002, Neikirk Decl., ¶¶ 78–79. First, Patent Owner argues that essentially silicon nitride is an inferior material to use for Anzai’s planarization layer 17 compared with organic resin. PO Resp. 13–15. However, “[i]t’s not necessary to show that a combination is the best option, only that it be a suitable option.” Intel Corp. v. Qualcomm Inc., 21 F.4th 797, 800 (Fed. Cir. 2021) (emphasis in original). Patent Owner does not argue that silicon nitride would not work, but rather that it would be more difficult and more expensive to use. See PO Resp. 14. But “the fact that the two disclosed apparatus[es] would not be combined by businessmen for economic reasons is not the same as saying that it could not be done because skilled persons in the art felt that there was some technological incompatibility that prevented their combination. Only the latter is telling on the issue of nonobviousness.” Grit Energy Solutions LLC v. Oren Techs., LLC, 957 F.3d 1309, 1323 (Fed. Cir. 2020) (quoting Orthopedic Equip. Co., Inc. v. United States, 702 F.2d 1005, 1013 (Fed. Cir. 1983)). “Likewise, a given course of action often has simultaneous advantages and disadvantages, and this does not necessarily obviate motivation to combine.” Medichem, S.A. v. Rolabo, S.L., 437 F.3d 1157, 1165 (Fed. Cir. 2006). Here, Petitioner explains that “a POSITA would have known that organic materials usually have lower dielectric constants than inorganic materials, such as SiN, and a higher dielectric constant is desirable for the insulator in a capacitor since that leads to higher capacitance per unit area.” Pet. 26 (citing Ex. 1002, Neikirk Decl., ¶ 78). Petitioner further explains that this “then allows a reduced area storage capacitance element, one of the objectives of Anzai.” Id. (citing Ex. 1003, code (57)). Patent Owner’s focus mainly on planarization (PO Sur-reply 16–17) ignores that the Anzai’s planarization layers 17 and 19 also “function as the capacitance insulating film.” Ex. 1003, 5:65–67. Thus, although there are tradeoffs, Petitioner has shown sufficiently that a POSITA would have been motivated to incorporate the teachings of Yamazaki regarding potential materials for planarization layers 17 and 19. Second, Patent Owner argues that a Petitioner has failed to provide an adequate reason to select silicon nitride from Yamazaki’s list of potential materials. We disagree. Petitioner has explained the benefits of selecting a high dielectric inorganic material. Pet. 26. Yamazaki provides only three potential options—silicon oxide, silicon nitride, and silicon oxynitride. See Ex. 1004, 11:45–50. Moreover, Dr. Neikirk testified, supported by multiple references, that using silicon nitride was well known in the prior art at the time of the invention. See Ex. 1002, Neikirk Decl., ¶ 75 (citing Ex. 1007; Ex. 1008; Ex. 1009). “When there is a design need or market pressure to solve a problem and there are a finite number of identified, predictable solutions, a person of ordinary skill has good reason to pursue the known options within his or her technical grasp.” KSR, 550 U.S. at 421. Indeed, “[i]f a person of ordinary skill can implement a predictable variation, § 103 likely bars its patentability.” Id. at 417. This is the case here. Petitioner has shown that a person of ordinary skill seeking to improve the capacitance of Anzai’s planarization layers 17 and 19, without increasing the size of the capacitor, would have looked at the inorganic materials identified in Yamazaki as suitable for the purpose, and it would have been would obvious to choose silicon nitride, a well-known, and predictable material for the application. Thus, we disagree with Patent Owner that Petitioner has failed to show a sufficient reason for selecting silicon nitride from Yamazaki’s list of suitable materials. Third, Patent Owner argues that Petitioner’s contentions only support” slip op. at 37

    Patent outcomesUS 7,586,121 unpatentable
    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 7,586,121
  • PTAB · Feb 11, 2026 · IPR2024-01221 · APJ Iftikhar Ahmed · IPR · Final written decision

    Petitioner failed to prove claims 1, 2, 4, 5, 7, 8, 12, 13, 17, 19–21, 23, 24, 26, 27, 29, 30, 34, 39–41, and 43 unpatentable because the cited grounds did not establish the required …

    RulingsFinal written decision
    • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

      “image capture device” refers to an imaging-based barcode reader and not a laser-based barcode scanner because we are persuaded that claim language and Specification support that interpretation and also because Patent Owner persuasively shows that a person of ordinary skill in the art would have understood the term as such. Claim 1 recites an “image capture device configured to capture an image.” Ex. 1001, 16:24–25. The plain meaning of the claim term requires that the image be captured, not just scanned. The claim further requires “generating an output based on the information embedded in the image,” requiring that information is retrieved from the captured image. Id. at 16:32–33. A device that does not capture an image is not an “image capture device” under the plain language of the claim. A laser-based barcode scanner employs light reflected from a laser beam to “generate an electrical signal that corresponds to the bars and spaces in the barcode being scanned.” See Ex. 2029 ¶¶ 42–43 (explaining in detail how laser-based barcode self-emitting a laser light across a code to be scanned, with a sensor tuned to capture the reflected light from the laser.”). It simply does not capture an image. slip op. at 14

    • Skill levelSkill level petitioner adoptedDecided for petitioner

      “Based on our review of the complete record, we determine that Petitioner’s stated level of ordinary skill in the art is reasonable because it is consistent with the evidence of record, including the asserted prior art. The field of the ’167 patent “relates generally to secure transactions, and more specifically, to methods and devices for providing secure identification, verification, and authorization using a portable secure device.” Ex. 1001, 1:8–11. The ’167 patent seeks “to provide methods and devices that are capable of providing secure transactions in a more efficient manner.” Id. at 3:11–13. Accordingly, we adopt Petitioner’s definition. We note, however, that our patentability analysis would be the same under Patent Owner’s definition.” slip op. at 11

    • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

      “We agree with Patent Owner that Wang fails to disclose limitation 1[a]. Wang discloses a portable electronic authorization device (PEAD) that can be used as a self-checkout terminal. Ex. 1004 ¶ 115. In this context, Wang discloses By entering the UPC code or barcode using keypad on the PEAD or scanning in the UPC code or barcode using the input device built into the PEAD such as a barcode scanner or OCR reader, the PEAD can generate the receipt with the list of item prices through the wireless network and Internet by querying the item price using the barcode as the index for price lookup table which is Stored in a Server System. Id. (emphasis added). As discussed above (Section III.C.1), we are persuaded by Patent Owner’s arguments that the claimed “image capture device” refers to an imaging-based device and not a laser-based barcode scanner. Petitioner does not contend that Wang’s disclosure of the barcode scanner necessarily refers to an imaging-based device, but argues that Wang’s disclosure is sufficient because “both imaging-based barcode scanners and laser-based barcode scanners constitute image capture devices.” Reply 11. In light of our claim construction above, we disagree.” slip op. at 27

    • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable

      “Petitioner contends that claims 1, 4, 5, 7, 12, 17, 23, 26, 27, 29, 34, and 43 are unpatentable as obvious over the combination of Wang and Drummond. Pet. 30–43. 1. Drummond Drummond is a patent titled “Automated Banking Machine System and Method,” and “relates to an automated banking machine apparatus and system that are capable of use in a wide area network, and which provides a user with a remote electronic receipt or other record related to a transaction performed at the machine.” Ex. 1008, code (54), ¶ 2. Drummond discloses that its automated banking machine, may “initiate the sending of a non-paper transaction receipt to the customer,” “[t]he receipt may be sent using a wide area network, such as the Internet,” and “[t]he receipt may be an electronic receipt, for example a receipt in the form of an e-mail message.” Id. ¶ 247. 2. Claims 1, 4, 5, 7, 12, 17, 23, 26, 27, 29, 34, and 43 For this obviousness ground, Petitioner relies on the same arguments and evidence as its Ground 1a (anticipation by Wang), discussed above, for the majority of claim limitations. See Pet. 33–43. Importantly, Petitioner relies solely on Wang as teaching independent claim limitations [1a], [23a], and [43b] relating to an image capture device and embedded information. Pet. 36, 41, 43. Accordingly, for the reasons discussed above with respect to Ground 1a, Petitioner has not established by a preponderance of the evidence, that the subject matter of claims 1, 4, 5, 7, 12, 17, 23, 26, 27, 29, 34, and 43 would have been obvious to one of ordinary skill in the art over the combination of Wang and Drummond.” slip op. at 31

    Patent outcomesUS 7,314,167 not shown unpatentable
    Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
    Patents in suitUS 7,314,167

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.