• Apple Inc. v. RJ Technology LLCSome claims unpatentable
  PTAB · Feb 18, 2025 · IPR2023-01350 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 5–10 are unpatentable as obvious; claims 11–14 were not shown unpatentable because the evidence did not establish the claimed capacity retention after 400 cycles.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends a person of ordinary skill in the art “would have held a Bachelor’s degree in chemistry or chemical engineering, with at least 4 years of experience in cell design, electrochemical techniques, and battery materials development.” Pet. 4. Petitioner further contends that a “Master’s Degree can substitute[] for some of the relevant experience,” and “[e]quivalent training with battery specific experience can accommodate other degreed fields.” Id. 9 The parties here do not address objective evidence of nonobviousness. Patent Owner does not dispute Petitioner’s definition of the ordinarily skilled artisan. PO Resp. 20. We adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the ’641 patent, the prior art of record, and the parties’ arguments.” slip op. at 6

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “The parties agree that the term “charge cut-off voltage” is “the maximum voltage to which the battery is configured to be charged.” PO Resp 21–22; Pet. Reply 1. The parties dispute, however, whether the “charge cut-off voltage” is a “battery property” or “the voltage applied to the battery during charging.” PO Resp. 21–24; Pet. Reply 1–6. We need not resolve the precise meaning of “charge cut-off voltage” because there is no dispute that Yamaki discloses this limitation under either party’s interpretation of the claim term. Upon review of the prior art and the parties’ arguments, we determine that no terms of the ’641 patent require express construction. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))); Pet. Reply 1 (asserting that the challenged claims are unpatentable under either parties’ construction of “charge cut-off voltage”).” slip op. at 7

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “Patent Owner’s arguments do not persuasively undermine Petitioner’s position. Sakamoto expressly discloses setting the ratio of negative to positive electrode active material in the range of 1.05 to 1.30. Ex. 1005 ¶ 8. Sakamoto also explains why this range is preferable, i.e., if the ratio is roughly equal “the charge-discharge cycle performance is insufficient due to significant deterioration from charging and discharging,” and if the ratio is 10 Citations to the prosecution history of Yamaki are to the page numbers added to the lower right corner of the document. too high “too much of the compound does not participate in charging and discharging.” Id. ¶¶ 6, 8. These disclosures are sufficient to explain why one of ordinary skill in the art would have found it obvious to select the ratios disclosed in Sakamoto in Yamaki. Id. ¶ 8 (providing a secondary battery with a capacity ratio between 1.05 and 1.30 and noting that by setting the ratio within this range the resulting secondary lithium battery is “safe due to low risk of heat being generated and an explosion occurring”). We also disagree that Sakamoto teaches away from elevated voltages or from increasing the amount of lithium in circulation. See PO Resp. 29. Contrary to Patent Owner’s arguments, Sakamoto provides no general teaching against using a charge cut-off voltage above 4.2 V, or against increasing the level of lithium in circulation. Nor does Sakamoto “criticize, discredit, or otherwise discourage” the claimed invention. In re Fulton, 391 F.3d 1195, 1201 (Fed. Cir. 2004). Rather, Sakamoto warns against setting the reversible capacities of the positive and negative electrode substantially equal as this may result in excess lithium plating on the surface of the electrode. Ex. 1005 ¶¶ 6, 8. We agree with Petitioner that this disclosure would lead one of ordinary skill in the art to design a battery with a higher capacity in the negative electrode active material than the positive electrode active material. Pet. 11–12.” slip op. at 14

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner

    “We also disagree that Sakamoto teaches away from elevated voltages or from increasing the amount of lithium in circulation. See PO Resp. 29. Contrary to Patent Owner’s arguments, Sakamoto provides no general teaching against using a charge cut-off voltage above 4.2 V, or against increasing the level of lithium in circulation. Nor does Sakamoto “criticize, discredit, or otherwise discourage” the claimed invention. In re Fulton, 391 F.3d 1195, 1201 (Fed. Cir. 2004). Rather, Sakamoto warns against setting the reversible capacities of the positive and negative electrode substantially equal as this may result in excess lithium plating on the surface of the electrode. Ex. 1005 ¶¶ 6, 8. We agree with Petitioner that this disclosure would lead one of ordinary skill in the art to design a battery with a higher capacity in the negative electrode active material than the positive electrode active material. Pet. 11–12.” slip op. at 15

  Patent outcomesUS 7,749,641 mixed
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 7,749,641
• Samsung Electronics Co., Ltd. / Apple Inc. v. RJ Technology LLCSome claims unpatentable
  PTAB · Jan 17, 2025 · IPR2024-00597 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 2–4 and 6–18 are unpatentable as obvious over Abe and Guyomard, with claims 9–10 also obvious over Iwaizono; claims 1 and 5 were not shown unpatentable.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art “would have had a Master’s degree in material science, chemical engineering, chemistry, or similar field with four years of experience designing testing, and building secondary lithium batteries.” Pet. 11 (citing Ex. 1002 ¶ 51). Petitioner further contends that a person of ordinary skill in the art would have been aware of “(1) positive electrode materials, (2) negative electrode materials, (3) separators, (4) electrolytes, (5) charge-discharge parameters, and (6) protection circuits, as well as ‘battery failure modes’ such as plating and the formation of dendrites.” Id. (citing Ex. 1002 ¶¶ 50–51). Patent Owner “does not dispute Petitioner’s level of ordinary skill.” PO Resp. 17. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the disclosures of the ’641 patent and the prior art of record.” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “We also agree with Patent Owner that the charge cut-off voltage is not necessarily the applied voltage during charging. PO Resp. 20. Rather, depending on the charging protocol used and when in the charging cycle the voltage is applied, the applied voltage could be higher than the battery voltage. Ex. 2013; Ex. 2006 ¶ 91. For example, as discussed in more detail below with respect to the Uemura grounds, when fast charging using constant current is used and the charging rate is not slow, the applied voltage will be higher than the battery voltage when the constant current charging phase is stopped. Ex. 2006 ¶ 91; Ex. 2013. Likewise, during constant current/constant voltage charging, the applied voltage approximates the battery voltage only when the battery is nearly completely charged. Ex. 2013; Ex. 2006 ¶ 91. Thus, the applied voltage may be, but is not necessarily, the charge cut-off voltage. In view of the foregoing, we construe “charge cut-off voltage” in claims 1 and 5 as “the maximum value to which the battery is configured to be charged.” PO Resp. 18; Ex. 2008, 217:6–11; Pet. Reply 5. Contrary to Patent Owner’s arguments, however, we do not understand the phrase “configured to be charged” to necessarily represent a single voltage for the battery that is determined based on the structure and chemistry of the battery. Pet. Reply 4–5. Rather, the charge cut-off voltage is a selected potential, or voltage, of the battery or cell at the end of charging that is controlled by a circuit or device, such as a charger or control circuit within the battery. Ex. 1001, 9:50–55; Ex. 1048, 2, 7–8; Ex. 1008, 3:9–13. And, for the reasons discussed herein, the charge cut-off voltage may be, but is not necessarily, the same as the applied voltage during charging. PO Resp. 20.” slip op. at 15

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “charge cut-off voltage “greater than 4.2 V but less than 5.8 V” and calculating a specific or theoretic capacity “with a charge cut-off voltage limited to 4.2” (claim 1) or “with a charge cut-off voltage set at 4.2 V” (claim 5). Ex. 1001, 16:56–61, 17:6–11. Although the parties dispute the precise scope of these claim terms, the parties agree that the first use of “charge cut-off voltage” in claims 1 and 5 refers to the potential of the battery as a whole (between the cathode and the anode), and not a half-cell voltage using lithium metal as a counter electrode.10 Tr. 17:1–3 (agreeing 10 With respect to the phrase “as calculated by a theoretic capacity with a charge cut-off voltage set at 4.2 V,” the parties in fact appear to be in that the first use of “charge cut-off voltage” in claim 5 refers to a full-cell voltage); Sur-reply 5; PO Resp. 22. We need not further construe the claims to resolve the disputes between the parties. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 16

  • Expert testimonyPatent owner expert creditedDecided for patent owner

    “Given Mr. Juzkow’s unambiguous testimony that Uemura uses constant current charging that would stop when the applied voltage reached 11 The chart is reproduced from SAFT, Charging your lithium-ion batteries: 5 expert tips for a longer lifespan, (https://www.saft.com/energizing-iot/charging-your-lithium-ion-batteries-5-expert-tips-longerlifespan#:~: text=When%20the%20battery%20provides%20current,This%20restore s%20the%20battery's%20capacity). 4.3 V, as well as Dr. Yao’s persuasive testimony that Uemura’s constant charging rate is not slow, we credit the testimony of Dr. Yao that one of ordinary skill in the art would have understood that the internal voltage to which the battery of Uemura was charged is less than 4.3 V. Ex. 2006 ¶ 119. In particular, Dr. Yao persuasively testifies that one of ordinary skill in the art would have believed that the charge cut-off voltage was no more than 4.2 V, and most likely equal to “about 4 V.” Id. ¶¶ 119–122.” slip op. at 21

  Patent outcomesUS 7,749,641 mixed
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 7,749,641
• Samsung Electronics Co., Ltd. / Apple Inc. v. RJ Technology LLCSome claims unpatentable
  PTAB · Jan 17, 2025 · IPR2023-01183 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 2–4 and 6–18 are unpatentable as obvious over Abe and Guyomard, with claims 9 and 10 also obvious over Iwaizono; claims 1 and 5 were not shown unpatentable.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art “would have had a Master’s degree in material science, chemical engineering, chemistry, or similar field with four years of experience designing testing, and building secondary lithium batteries.” Pet. 11 (citing Ex. 1002 ¶ 51). Petitioner further contends that a person of ordinary skill in the art would have been aware of “(1) positive electrode materials, (2) negative electrode materials, (3) separators, (4) electrolytes, (5) charge-discharge parameters, and (6) protection circuits, as well as ‘battery failure modes’ such as plating and the formation of dendrites.” Id. (citing Ex. 1002 ¶¶ 50–51). Patent Owner “does not dispute Petitioner’s level of ordinary skill.” PO Resp. 17. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the disclosures of the ’641 patent and the prior art of record.” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “constructions. First, we agree with Petitioner that the ’641 patent indicates that the charge cut-off voltage selected for a particular battery need not be a fixed property of the battery or something that is set by the design and chemistry of the battery. Consistent with this conclusion, the ’641 patent discloses that a “charging device controls the charge cut-off voltage of the single lithium-ion cell within a range from 4.3 V to 5.8 V.” Ex. 1001, 9:50– 55. This strongly suggests that the charge cut-off voltage is controlled by the charger and is not necessarily an inherent property of the battery. Patent Owner contends that this is merely an unclaimed embodiment, but the relevant disclosure states that the charging device for the “present invention” may be any type of device “with the proviso that said charging device controls the charge cut-off voltage.” Id. at 9:50–53.” slip op. at 12

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “charge cut-off voltage “greater than 4.2 V but less than 5.8 V” and calculating a specific or theoretic capacity “with a charge cut-off voltage limited to 4.2” (claim 1) or “with a charge cut-off voltage set at 4.2 V” (claim 5). Ex. 1001, 16:56–61, 17:6–11. Although the parties dispute the precise scope of these claim terms, the parties agree that the first use of “charge cut-off voltage” in claims 1 and 5 refers to the potential of the battery as a whole (between the cathode and the anode), and not a half-cell voltage using lithium metal as a counter electrode.10 Tr. 17:1–3 (agreeing 10 With respect to the phrase “as calculated by a theoretic capacity with a charge cut-off voltage set at 4.2 V,” the parties in fact appear to be in that the first use of “charge cut-off voltage” in claim 5 refers to a full-cell voltage); Sur-reply 5; PO Resp. 22. We need not further construe the claims to resolve the disputes between the parties. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 16

  • Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner

    “Given Mr. Juzkow’s unambiguous testimony that Uemura uses constant current charging that would stop when the applied voltage reached 11 The chart is reproduced from SAFT, Charging your lithium-ion batteries: 5 expert tips for a longer lifespan, (https://www.saft.com/energizing-iot/charging-your-lithium-ion-batteries-5-expert-tips-longerlifespan#:~: text=When%20the%20battery%20provides%20current,This%20restore s%20the%20battery's%20capacity). 4.3 V, as well as Dr. Yao’s persuasive testimony that Uemura’s constant charging rate is not slow, we credit the testimony of Dr. Yao that one of ordinary skill in the art would have understood that the internal voltage to which the battery of Uemura was charged is less than 4.3 V. Ex. 2006 ¶ 119. In particular, Dr. Yao persuasively testifies that one of ordinary skill in the art would have believed that the charge cut-off voltage was no more than 4.2 V, and most likely equal to “about 4 V.” Id. ¶¶ 119–122. Petitioner argues that because the battery of Uemura is charged “to” a maximum voltage of 4.3 V, Uemura discloses the claimed charge cut-off voltage under either Petitioner’s or Patent Owner’s construction of the term. Pet. Reply 11–12 (citing Ex. 1009 ¶ 81; Ex. 1044 ¶¶ 56–59). This argument is not persuasive because Mr. Juzkow unambiguously testified that charging in Uemura stopped when the applied voltage reached 4.3 V, and Uemura discloses that the battery was charged “at” a voltage ranging from 4.3 V to 2.0 V, not “to” such a voltage. Ex. 1009 ¶ 81; Ex. 2008, 113:2–13; Ex. 2006 ¶ 119 n.64; Sur-reply 9. In view of the foregoing, we determine that Petitioner has not demonstrated by a preponderance of the evidence that Uemura anticipates independent claims 1 and 5 of the ’641 patent.” slip op. at 21

  Patent outcomesUS 7,749,641 mixed
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 7,749,641
• Chongqing Yanmei Technology Co., Ltd. v. Terves, LLCSome claims unpatentable
  PTAB · Aug 27, 2024 · IPR2023-00521 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 19–61, 63–77, and 79 are unpatentable as anticipated by Doud; claims 78, 80, and 81 are not shown unpatentable. The contingent motion to amend is granted in part and denied in part.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art “would have at least a Ph.D. in chemistry, metallurgy, or material science or material engineering” or, in the alternative, “would have a Bachelor of Science or Master of Science degree in one of these disciplines plus experience involving the use and design of dissolvable metal alloys for use in creating tools and other downhole parts for well drilling or completion activities.” Pet. 13–14. Patent Owner does not oppose Petitioner’s contentions regarding the level of ordinary skill in the art. PO Resp. 12 n.4. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the ordinarily skilled artisan as it is consistent with the prior art of record.” slip op. at 7

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

    “With respect to claim 19, Petitioner proposes constructions for the terms “in situ precipitate” and “a plurality of particles of said in situ precipitate having a size of no more than 50 µm.” Pet. 11–12. With respect to claims 76–81, Petitioner proposes a construction for the term “wherein said additive material includes one or more metal materials selected from the group consisting of 0.1–35 wt. % copper, 0.1–24.5 wt. % nickel and 0.1–20 wt. % cobalt.” Id. at 13. Patent Owner contends no claims require construction for purposes of this Decision. PO Resp. 12 n.4, 17–18; Mot. 16–17. Upon review of the prior art of record, we determine that no claim terms require express construction for purposes of this Final Written Decision. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 8

  • Disclosure Requirements (§112) › Written description (Ariad)Written description inadequateWritten description adequateMixed

    “Ex. 2027, 20:25–21:5 (emphasis added). The disclosure that the “magnesium composite” of “[t]he present invention” “includes at least 50 wt% magnesium” is unambiguous and constitutes strong evidence that the inventors were not in possession of a magnesium composite with less than 50 wt. % magnesium, or additive concentrations above 50 wt. %. See SciMed Life Systems, Inc. v. Advanced Cardiovasular Systems, Inc., 242 F.3d 1337, 1343 (Fed. Cir. 2001) (noting that a description of the “present invention” as having a particular structure “is strong evidence that the claims should not be read to encompass the opposite structure”). Consistent with this conclusion, the original claims of the ’295 application all limited the additive material in the composite to 0.05 wt %–45 wt %. Ex. 2027, 26:1– 13, 29:9–15. Likewise, in each example where copper, nickel, or cobalt additives are used in the range recited in the proposed substitute claims, the magnesium composite is “over 50 wt% magnesium,” and any claims that do not require this range of magnesium are limited to an additive range of “about 0.05 wt%–45 wt% of said mixture.”8 Ex. 2027, 6:13–7:4, 7:16–19, 8 Written description support is considered from the view point of the ordinarily skilled artisan. Ariad Pharms., Inc. v. Eli Lilly and Co., 598 F.3d 1336, 1351 (Fed. Cir. 2010) (en banc). Patent Owner, bearing the burden to show written description support in any priority application for which it seeks the benefit of its filing date, provides no testimony from an ordinarily skilled artisan regarding written description support in the ’295 application, or any evidence to show what such an artisan would conclude from the express disclosures of the ’295 application. Lectrosonics, Paper 15 at 7; In re NTP, 654 F.3d 1268, 1276 (Fed. Cir. 2011) (noting that “a patent’s claims are not entitled to an earlier priority date merely because the patentee claims priority . . . Rather, for a patent’s claims to be entitled to an earlier priority date, the patentee must demonstrate that the claims meet the requirements of 35 U.S.C. § 120”). Where there is any ambiguity in the disclosures of the ’295 application, the absence of supporting testimony tends to cut against 26:2–31:2; see Ex. 1005 ¶¶ 12, 13, 18, 19, 16–21, 26, 28, claims 16–21, 26– 28. In view of the foregoing, we are not persuaded that Patent Owner has demonstrated that the inventors of the priority applications were in possession of a magnesium cast composite that included less than 50 wt. % magnesium, or greater than 50 wt. % additives. As proposed substitute claim 104 encompasses a magnesium cast composite with up to 90 wt. % additives, and therefore as little as 10 wt. % magnesium, Patent Owner has not demonstrated that the full scope of this claim finds written description support in any application prior to the ’915 application, filed on October 12, 2018.” slip op. at 17

  • Disclosure Requirements (§112) › Definiteness (Nautilus)DefiniteIndefiniteMixed

    “The definiteness requirement of § 112(a) is satisfied when “a patent’s claims, viewed in light of the specification and prosecution history, inform those skilled in the art about the scope of the invention with reasonable clarity.” Nautilus, Inc. v. Biosig Instruments, Inc., 572 U.S. 898, 910 (2014); see 37 C.F.R. § 42.100(b) (changing the claim construction standard used to review a claim proposed in a motion to amend from the broadest reasonable construction to the “same construction standard that would be used to construe the claim in a civil action under 35 U.S.C. [§] 282(b)”). Proposed substitute claim 104 generically requires “in situ precipitate” and also a specific type of in situ precipitate: “in situ galvanically-active intermetallic precipitate.” Mot. Appendix A. Although this claim would have best been clarified by Patent Owner after seeking preliminary guidance on its Motion to Amend, upon review of the written description, claims, and figures of the ’740 patent, as well as Patent Owner’s clarification in its Reply to the Opposition, we agree with Patent Owner that one of ordinary skill in the art would have understood that the “in situ galvanically-active intermetallic precipitate” is merely a more complete description of the “in situ precipitate” mentioned earlier in the sentence. Mot. Reply 4. As such, we do not find that this part of proposed substitute claim renders claim 104 indefinite.” slip op. at 22

  Patent outcomesUS 10,689,740 mixed
  Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Graham · Nautilus
  Patents in suitUS 10,689,740
• Samsung Electronics Co., Ltd. v. Lynk Labs, Inc.Some claims unpatentable
  PTAB · May 5, 2023 · IPR2022-00098 · APJ Arthur M Peslak · IPR · Final written decision

  Claims 1, 3, and 4 are unpatentable as obvious over the stated combinations; claim 2 was not shown unpatentable because the driver was not shown configured to receive the rectifier’s forward voltages.

  RulingsFinal written decision

  • Skill levelSkill level patent owner adoptedDecided for patent owner

    “We agree with Patent Owner that a person of ordinary skill in the art would have had experience in LED devices. For this reason, we apply Patent Owner’s proposed level of ordinary skill in the art because it comports with the level of skill reflected in the ’149 patent and the prior art of record. However, if we were to apply Petitioner’s proposed level of skill, our Decision would not be affected.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Upon review of the entire record, we determine that no claim terms require express construction. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (noting that “we need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy’”) (citing Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 10

  • Expert testimonyPetitioner expert creditedPatent owner expert discountedMixed

    “Dr. Ducharme’s testimony that “the spacing of the chips in Zhang would not likely be so close as to create overheating issues” (Ex. 2002 ¶ 111) is unsupported by any disclosure of the actual spacing of Zhang’s chips. Consequently, his testimony that there would be no overheating concerns in Zhang due to the spacing of the chips is entitled to little, if any, weight. Dr. Ducharme further testifies that the components of Zhang’s driver “could easily increase the temperature of the LED 19 chips on the circuit board, which can cause LEDs to generate less illumination, burn out and otherwise adversely affect their performance.” Ex. 2002 ¶ 126. Dr. Ducharme further testifies that “[i]t is well-known that excessive operational temperatures can reduce the illumination provided by the LEDs, can decrease the operational lifetime of the LEDs, and if the temperature is sufficiently high, it can cause LED junction failure and a burnt-out LED.” Id. We agree with this testimony, which as discussed below, is consistent with Salam. Dr. Ducharme’s testimony concerning overheating issues caused by the driver components contradicts Patent Owner’s ’s contention that there would not be “an overheating issue with Zhang’s LED exit sign circuit in Figure 2.1.” PO Resp. 30. Regardless of whether Zhang’s LEDs in Figure 2.1 have a heat problem or not, Salam teaches the advantages of using a heat sink. Salam teaches that a heat sink will result in a higher efficiency of the LEDs and improved life. Ex. 1006, 16:38–43. The Federal Circuit, in DyStar Textilfarben GmBH & Co v. C.H. Patrick Co., 464 F.3d 1356 (Fed. Cir. 2006), stated that “the desire to enhance commercial opportunities by improving a product or process is universal–and even common-sensical . . . the proper question is whether the ordinary artisan possesses the knowledge and skills rendering him capable of combining the prior art references.” Id. at 1368. Dr. Ducharme testified that a person of ordinary skill in the art “would have an understanding of the generation of heat and using a heat sink to remove unwanted heat from electronics and LED lighting devices.” Ex. 1102, 23:18–24:3. Dr. Ducharme’s testimony is consistent with Petitioner’s contention that the combination of Zhang and Salam “would have been a straightforward combination of known components and technologies, according to known methods, to produce the predictable result of reducing/ mitigating heat effects in a circuit.” Pet. 17 (citing Ex. 1002 ¶ 106). Patent Owner next contends it would be extremely burdensome and costly to modify Zhang to add a heat sink layer because “each of the multiple chips mounted and epoxied to Zhang’s circuit board in the exit sign would have to be modified.” PO Resp. 30 (citing Ex. 2002 ¶ 112). Dr. Ducharme’s testimony repeats the Patent Owner Response verbatim and is entitled to little, if any, weight. Ex. 2002 ¶ 112. Nonetheless, this contention is unavailing because it is based on Patent Owner’s bodily incorporation of Zhang and Salam. Patent Owner next contends that a person of ordinary skill in the art” slip op. at 27

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “Regardless of whether Zhang’s LEDs in Figure 2.1 have a heat problem or not, Salam teaches the advantages of using a heat sink. Salam teaches that a heat sink will result in a higher efficiency of the LEDs and improved life. Ex. 1006, 16:38–43. The Federal Circuit, in DyStar Textilfarben GmBH & Co v. C.H. Patrick Co., 464 F.3d 1356 (Fed. Cir. 2006), stated that “the desire to enhance commercial opportunities by improving a product or process is universal–and even common-sensical . . . the proper question is whether the ordinary artisan possesses the knowledge and skills rendering him capable of combining the prior art references.” Id. at 1368. Dr. Ducharme testified that a person of ordinary skill in the art “would have an understanding of the generation of heat and using a heat sink to remove unwanted heat from electronics and LED lighting devices.” Ex. 1102, 23:18–24:3. Dr. Ducharme’s testimony is consistent with Petitioner’s contention that the combination of Zhang and Salam “would have been a straightforward combination of known components and technologies, according to known methods, to produce the predictable result of reducing/ mitigating heat effects in a circuit.” Pet. 17 (citing Ex. 1002 ¶ 106).” slip op. at 27

  Patent outcomesUS 10,517,149 mixed
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 10,517,149
• Home Depot USA, Inc. v. Lynk Labs, Inc.Some claims unpatentable
  PTAB · May 5, 2023 · IPR2022-00023 · APJ Arthur M Peslak · IPR · Final written decision

  Claims 1 and 4 are unpatentable over the stated § 103 combinations; Petitioner did not show claim 2 unpatentable because it did not explain how the LED array’s forward voltage is received by the driver.

  RulingsFinal written decision

  • Skill levelSkill level board ownOther

    “degree in electrical engineering, or similar technical field, with two years of experience in the field of design and/or development of light-emitting diodes (LEDs) and circuits in the context of lighting control systems.” Pet. 11–12 (citing Ex. 1002 ¶ 34). Petitioner further contends that “[a]n increase in experience could compensate for less education.” Id. at 12. Patent Owner proposes the same level of skill in the art. See PO Resp. 6. We apply the parties’ undisputed level of ordinary skill in the art because it comports with the level of skill reflected in the ’149 patent and the prior art of record.” slip op. at 8

  • Expert testimonyPetitioner expert creditedDecided for petitioner

    “We credit Dr. Lebby’s testimony over Dr. Ducharme for the following reasons. First, in Deese, power cable 28 is inserted into an opening in rubber housing 21. Ex. 1008, Fig. 2A. [R]ubber housing 21 forms a water-tight seal around the power cable 28.” Id. at 4:63–65. Dr. Ducharme does not explain why Hochstein’s protruding heat sink shell could not similarly be inserted through rubber housing 21 with a water-tight seal. Further, Dr. Lebby relies on the similarity between the structures of Deese and Hochstein. Hochstein uses gasket 45 and weather seal 48 to seal housing 10 with electrical lead 49 and heat sink shell 38 extending therethrough. Ex. 1010, 5: 39–40, 5:63:65, Fig. 8.” slip op. at 47

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed patent owner constructionOther

    “Our analysis starts with the claim language. Claim 1 recites “a driver, wherein the driver includes at least one transistor and at least one capacitor” and “the driver is configured to receive an AC voltage from a mains power source and provide a voltage and current to the at least one LED circuit.” Ex. 1001, 23:16–17, 26:22–24. Dr. Ducharme testifies that power is determined by multiplying voltage and current. Ex. 2008 ¶ 63. The language of claim 1, thus, supports Patent Owner’s construction which is also consistent with the dictionary definition offered by Petitioner which also defines “driver” as [a] program, circuit or device used to power or control other programs, circuits or devices.” Ex. 1007, 4 (emphasis added). The Specification provides “the driver providing an AC voltage and current to one or more LED circuits.” Ex. 1001, 3:65–67. Thus, the Specification also provides support for Patent Owner’s construction. For the foregoing reasons, we apply Patent Owner’s proposed construction of “driver” because it is consistent with the language of claim 1 and the description of driver in the Specification. We note that the adjective “LED” prior to circuits or devices in Patent Owner’s construction is not necessary because that it essentially repeats limitation 1.e.” slip op. at 12

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITADecided for petitioner

    “We begin with the claim language itself which is “the package is a heat sinking reflective material.” Ex. 1001, 23:18–19 (emphasis added). In its analysis, Patent Owner parses “heat sinking reflective material” out of context by omitting the italicized language “the package is” preceding “heat sinking reflective material.” PO Resp. 29. The deposition testimony of Dr. Lebby and Dr. Ducharme’s declaration testimony cited by Patent Owner are also out of context. The Specification of the ’149 patent defines “package” as an integrated unit that “in certain applications may preferably include a heat sink, a reflective material, a lens for directing light, phosphor nano-crystals or light changing or enhancing substances.” Ex. 1001, 5:30–33. Because heat sink and reflective material are listed separately in the Specification, this disclosure suggests that, at least in certain embodiments, a package with a heat sink separate from a reflective material would fall within the scope of limitation 1.c. This is further confirmed by comparing the packages illustrated in Figures 25 and 26 of the ’149 patent which are reproduced above. Figure 25 is described as illustrating “heat sinking material 198 . . . integrated into the package 30.” Id. at 17:34–35. Figure 26 is described as illustrating reflector 202 “integrated into the package 30 for optimized light dispersion.” Id. at 17:47–49. As can be seen from a visual comparison of Figures 25 and 26, reflector 202 is separate from heat sinking material 198. Given the disclosure in the ’149 patent of a package with a heat sink” slip op. at 15

  Patent outcomesUS 10,517,149 mixed
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,517,149
• Samsung Electronics Co., Ltd. v. Lynk Labs, Inc.Some claims unpatentable
  PTAB · Apr 19, 2023 · IPR2021-01576 · APJ Scott Raevsky · IPR · Final written decision

  Claims 1–12 are unpatentable as obvious; claims 13–18 are not shown unpatentable because the asserted combinations fail to teach or suggest multiple LED packages connected in series.

  RulingsFinal written decision

  • Skill levelSkill level patent owner adoptedDecided for patent owner

    “PO Resp. 8 (citing Ex. 2001 ¶¶ 41–42). Patent Owner argues that its definition is superior because Petitioner’s “and/or” qualifier “might be read as considering a person who has ‘related circuit design’ experience but no experience with ‘LED devices’ to be a POSITA.” Id. at 9. Patent Owner further views Petitioner’s “or a related field” phrasing as potentially including a person who has no experience with LED devices. Id. We agree with Patent Owner on both points. We agree with Patent Owner that Patent Owner’s proposal is more consistent with the problems and solutions in the ’979 patent and prior art of record. We adopt Patent Owner’s definition of the level of skill but note that had we adopted Petitioner’s level of skill, we would not have reached a different outcome here.” slip op. at 6

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “specification support its construction of “formed or mounted to” as encompassing indirect attachment to the substrate. Neither the plain claim language nor the specification requires the phosphor coating to be directly attached to the substrate. Limitation 1(c) recites, wherein the LED chips comprise a phosphor coating to produce a change in a color or a quality of light emitted from the LED chips, wherein the LED chips, the power connection leads, and the phosphor coating are formed or mounted to a flexible substrate that is sufficiently flexible to be formed into a cylindrical shape[.] Ex. 1001, 22:7–12 (emphasis added). The claim is inartfully written, as it requires the LEDs to comprise a phosphor coating but then separately recites that the LED chips and the phosphor coating are formed or mounted to the substrate. But Petitioner correctly explains that the plain meaning requires that “the LED chips comprise a phosphor coating” and that “the [same] phosphor coating” (included in the LED chips) is “formed or mounted to a flexible substrate.” Reply 2. In other words, the use of the term “the” before “phosphor coating” indicates reliance on the antecedent basis of “LED chips comprise a phosphor coating,” and thus the same coating of the LED chips is formed or mounted to the substrate. Logically, by including a phosphor coating with the LED chips, which are formed or mounted to the substrate, the coating of these chips is also indirectly formed or mounted to the substrate. Conversely, it would be illogical to conclude that the claim recites two phosphor coatings, one attached to the LED chips and another attached directly to the substrate, because the structure of the claim refers to a single phosphor coating of the LED chips. Even Patent Owner concedes that the claim encompasses the phosphor coating indirectly being mounted or attached to the substrate (in addition to being directly attached). PO Resp. 11 (“The ordinary English reading of the claim language does not encompass the phosphor coating only being indirectly attached to the substrate, instead, the language indicates that the coating is directly applied to the substrate.” (emphasis changed)), 13 (“the phosphor coating . . . is not merely attached to the substrate indirectly”).” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “After considering Patent Owner’s arguments, which we address below, we agree with Petitioner that the combination of Wojnarowski and Martin discloses this limitation and that a person of ordinary skill in the art would have been motivated to combine the references’ teachings in the manner asserted by Petitioner. Briefly, we summarize our findings, and then we address the parties’ arguments in more detail. First, we agree with Petitioner, and Patent Owner does not dispute, that Wojnarowski’s AC input voltage would have been converted to DC voltage in light of the bridge rectifier and capacitor disclosed by Wojnarowski. Pet. 25; Ex. 1002 ¶¶ 119– 20 (citing, e.g., Ex. 1005, 7:59–62, Fig. 24); PO Resp. 35–36 (acknowledging Wojnarowski discloses converting an AC input to a DC voltage). Second, we further agree with Petitioner, and Patent Owner does not dispute, that excessive current due to too few LEDs would have harmed Wojnarowski’s LEDs, and too small a current due to too many LEDs would be insufficient to power Wojnarowski’s LEDs. Pet. 26; Ex. 1002 ¶ 134; PO Resp. 48 (discussing, but not disputing, these assertions).13 Third, we agree that a POSITA would have recognized in view of Martin’s teachings and the knowledge of a skilled artisan that when configuring Wojnarowski’s device, the total forward voltage drop of the series-connected LEDs should approximately match the DC voltage output 13 Petitioner explains the relationship between voltage and current for the LEDs as follows: “the total voltage drop of the circuit would dictate the current drawn by the LED circuitry, which would have been known to be inversely proportional to the voltage.” Pet. 26 (citing Ex. 1002 ¶ 134). of Wojnarowski’s circuit. Pet. 26–27 (citing Ex. 1002 ¶¶ 132–38; Ex. 1008, Abstract (LED voltage “must be matched to the input source voltage”), ¶ 60 (“For AC or any other regularly varying input voltage, there is an additional requirement to direct drive voltage matching”)). For example, Martin teaches that “[t]he number of LEDs in the monolithic array may be selected to achieve a particular voltage drop across each device.” Ex. 1006 ¶ 22. Martin further explains, “[t]he voltage across each of the individual LEDs in the array is the line voltage divided by the number of LEDs in series,” and “[t]he number of LEDs is chosen such that the maximum voltage across each individual LED during the peak in the alternating current cycle is low enough so as not to damage the LEDs.” Id. The forward voltage drop across Martin’s 38 LEDs is about 171 V, which matches Martin’s AC input voltage peak of about 169.71 V. See id. (“At 120 RMS volts, the peak voltage will be about 180V [correction: 169.71 V],” and if the LEDs “can tolerate a maximum forward voltage of 4.5V, at least 38 LEDs connected in series are required.” (38 LEDs x 4.5 V = 171 V)); PO Resp. 41–42 (“While Martin references ‘about 180V,’ both parties agree that the correct value of the peak voltage Vp is 169.71 V.” (citing Ex. 1002 ¶ 127)). Although Martin’s LED forward voltage drop (171 V) differs slightly from the peak input voltage (169.71 V), Patent Owner conceded at the hearing that the claimed “matches” does not require an exact equivalence. Tr. 38:9–11 (“Patent Owner agrees . . . that matching has a meaning that goes beyond exact equivalence.”).14” slip op. at 22

  • Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication establishedDecided for petitioner

    “35 U.S.C. § 311(b). PO Resp. 22–25. This statute provides that “[a] petitioner in an inter partes review may request to cancel as unpatentable 1 or more claims of a patent only on a ground that could be raised under section 102 or 103 and only on the basis of prior art consisting of patents or printed publications.” § 311(b) (emphasis added). Patent Owner contends that Martin is not available as prior art under 35 U.S.C. § 311(b) because it is not a patent or printed publication and is only prior art under 35 U.S.C. § 102(e). PO Resp. 22. Patent Owner argues that documents are “printed publications” as of the date they become available to the public, and Martin became public on its publication date of October 21, 2004, after the February 25, 2004 priority date of the ’979 patent. Id. at 23. Patent Owner raises a similar argument for the Soules-II reference in Ground 6. Id. at 25– 26. Petitioner responds that the AIA framework permits the use of § 102(e) prior art in IPR proceedings, unlike formerly available covered business method review (CBM) proceedings, which restricted challenges to § 102(a) prior art. Reply 29. We agree. The statute governing the formerlyavailable CBM proceeding explicitly limits challenges based on “prior art that is described by section 102(a).” AIA § 18(a)(1)(C). In contrast, § 311(b) more broadly permits challenges “on the basis of prior art consisting of patents or printed publications.” The broader language in § 311(b) implies that unlike CBMs, IPRs are not limited to challenges solely under § 102(a) prior art. The parties cite to no Federal Circuit decisions that squarely address this issue. However, the Federal Circuit has applied § 102(e) patent application publication prior art in appeals from IPR proceedings. See, e.g., Purdue Pharma L.P. v. Iancu, 767 Fed. App’x 918, 920–21, 926 (Fed. Cir. 2019) (nonprecedential) (determining that a § 102(e) patent application publication was available as prior art in an IPR). The Board has also long permitted challenges based on patent application publications under § 102(e). See, e.g., Idle Free Sys., Inc. v. Bergstrom, Inc., IPR2012-00027, Paper 14 at 27 (PTAB Jan. 31, 2013) (instituting trial over § 102(e) ground based on a patent application publication). We therefore find Patent Owner’s § 311(b) argument unpersuasive.” slip op. at 34

  Patent outcomesUS 10,652,979 mixed
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 10,652,979
• Allstate Insurance Company v. Atos, LLCSome claims unpatentable
  PTAB · Mar 7, 2023 · IPR2021-01449 · APJ Julia Heaney · IPR · Final written decision

  Claim 5 is unpatentable as anticipated by Kim; claims 1–4 were not shown unpatentable under the asserted obviousness grounds.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Having considered the parties’ arguments and evidence, we adopt the level of ordinary skill in the art proposed by Petitioner, because it is consistent with the disclosures of the ’174 patent and the prior art of record. We note, however, that neither party contends that any issue in this case turns on the differences between the parties’ definitions of one of ordinary skill in the art.” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed petitioner constructionDecided for petitioner

    “Having reviewed the parties’ arguments and evidence, we determine that Petitioner’s proposed construction of “rotation vector” is consistent with the ’174 patent’s usage of the term “rotation vector” (or “vector of rotation”). See Ex. 1001, 1:54–2:11. Dr. Kanellakopoulos’s opinion supports that “rotation vector” would be understood by a person of ordinary skill in the art to describe the motion of a body that is rotating around a point. As to the other aspects of Patent Owner’s proposed construction, describing the characteristics of magnitude and direction, we determine that those attributes are not necessary to interpreting how a skilled artisan would understand “rotation vector” in light of the claim language and specification. See Tr. 47:26–48:7 (in Patent Owner’s proposed construction of “rotation vector,” “the magnitude requirement is not particularly important”). We address the parties’ arguments as to differences between a rotation vector and angular momentum vector in Section II.D.2 below, because they underlie Petitioner’s challenges involving Kleppner.” slip op. at 14

  • Claim Construction › Intrinsic evidence (Phillips canons) › Lexicography (patentee as own lexicographer)Term construed patent owner constructionDecided for patent owner

    “Having considered the parties’ positions as to construction of the term “movement vector” and applicability of the definition of “movement vector” set forth in the ’174 patent specification (Ex. 1001, 2:29–31), we construe the term “movement vector” to mean “a vector derived from the cross product of the centrifugal force vector and the rotation vector.” We adopt the definition set forth in the ’174 specification because we determine patentee acted as its own lexicographer. Cont’l Cirs. LLC v. Intel Corp., 915 F.3d 788, 796 (Fed. Cir. 2019) (citing Phillips, 415 F.3d at 1316) (“When the patentee acts as its own lexicographer, that definition governs.”). We agree with Petitioner that the words “while a vehicle is turning” would be superfluous in the construction, because the step of “detecting a movement vector during the turn” already recites that the vehicle is turning. Apple, Inc. v. Ameranth, 842 F.3d 1229, 1237 (Fed. Cir. 2016) (“Construing a claim term to include features of that term already recited in the claims would make those expressly recited features redundant.”)” slip op. at 16

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “We decline to adopt Patent Owner’s construction because it improperly reads into claim 5 a requirement that the specification and claim language do not support. The specification passages relied on by Patent Owner do not expressly state that a vehicle independent state must be determined while the device is inside a vehicle, and contrary to Patent Owner’s argument, they also do not necessarily imply that. For example, the descriptions of “vehicle independent movement” and “vehicle independent event” in the specification (see Ex. 1001, 1:16, 42) refer to “phone falling to the ground.” “Falling to the ground” implies that the phone may be outside a vehicle, not inside. Further, the specification’s reference to detecting a vehicle dependent state “while also” recognizing a vehicle independent event does not necessarily imply that the vehicle dependent state and vehicle independent event are being detected simultaneously, as Patent Owner argues. In the language of claim 5, a “vehicle independent state” is recited in the determining step (step c), and the requirement that the portable device is located “inside a vehicle” relates to creation of an operation indicator, as part of the detecting step (step b). Patent Owner does not dispute this, and agrees that a portable device “not in the vehicle” can satisfy the determining step (step c). Tr. 73:5–8. Patent Owner, however, argues step c’s recitation that a “vehicle independent state” is based on step b’s “predetermined criteria” creates a link between “vehicle independent state” and step b, and thus an “express requirement” in step c that the device is located inside the vehicle. See Tr. 73:8–26, 76:1–3. We decline to read this requirement into the claim language. Although the claim language states that determining a “vehicle independent state” is based on “predetermined criteria,” and step b describes comparing “predetermined criteria” to an “operation indicator” that is created when the device is inside a vehicle, it does not limit the step of determining a vehicle independent state to a time when the portable device is inside a vehicle. Accordingly, we construe “vehicle independent state” to mean a state triggered when the portable device is moved independently of the movement of the vehicle.” slip op. at 23

  Patent outcomesUS 9,846,174 mixed
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 9,846,174
• Nanofiber Solutions, LLC v. Acera Surgical, Inc.Some claims unpatentable
  PTAB · Dec 13, 2022 · IPR2021-01016 · APJ Christopher L Crumbley · IPR · Final written decision

  Claims 1, 2, 4–7, and 13 are unpatentable: claims 1, 2, 4, 5, and 13 as anticipated by Johnson, and claims 6 and 7 as obvious over Johnson and Johnson–Liu, respectively.

  RulingsFinal written decision

  • Skill levelOther

    “Petitioner contends that: A person of ordinary skill in the art (“POSITA”) at the time of filing the ‘228 Patent would have been a person having a bachelor's degree in science or engineering, for example in the fields of chemistry, chemical engineering, or biomedical engineering, with undergraduate research experience, coupled with at least three years of industry experience, that linked the fabrication of fibrous polymeric materials to performance requirements for scaffolds for the promotion of proliferation of biological cells and the growth and/or reconstruction of biological tissues. Pet. 11–12 (citing Ex. 1002 ¶¶ 112–116). In response, Patent Owner notes that all challenged claims recite electrospun fibers but that Petitioner’s proposed level of skill “requires (1) no coursework, training or experience with electrospinning and (2) improperly focuses on scaffolds for the promotion of proliferation of biological cells and the growth and/or reconstruction of biological tissues.” PO Resp. 7 (citing Ex. 2001, ¶¶ 38–39). But Patent Owner then concedes that this “difference is immaterial to deciding the issues raised by the Petition.” Id. at 8.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “construe claims “using the same claim construction standard that would be used to construe the claim in a civil action under 35 U.S.C. 282(b), including construing the claim in accordance with the ordinary and customary meaning of such claim as understood by one of ordinary skill in the art and the prosecution history pertaining to the patent.” 37 C.F.R. § 42.100(b); see Phillips v. AWH Corp., 415 F.3d 1303 (Fed. Cir. 2005) (en banc). Furthermore, we expressly construe the claims only to the extent necessary to resolve the parties’ dispute. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co. Ltd., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))). The parties agree that the terms of the challenged claims should be given their “plain and ordinary meaning” and that no express claim construction is necessary to address Petitioner’s challenges. Pet. 12; PO Resp. 6. We agree that no claim terms require express construction for purposes of resolving the dispute between the parties.” slip op. at 10

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableNot shown unpatentableMixed

    “Upon review, we are unpersuaded that Petitioner has improperly mixed and matched disclosures from Johnson to arrive at an anticipatory reference. Patent Owner is correct that Petitioner primarily relies on Example 1 as evidence for the method by which its scaffold is made. But the disclosure found in paragraph 98 is not a “distinct” teaching of the type described in Net MoneyIN; rather, it is a general description of the structures that may be created by Johnson’s method: “A scaffold may comprise any number of layers, including about 1 layer, about 2 layers, about 3 layers, about 4 layers, about 5 layers, and so on.” Ex. 1009 ¶ 98. Patent Owner has not directed us to anything in the disclosure of Johnson that indicates that this is a “distinct” teaching or embodiment, instead of a general description of the types of scaffolds that Johnson encompasses. We see no reason why the general disclosures regarding Johnson’s scaffolds should be limited to specific embodiments, or precluded from applying to the method of Example 1.” slip op. at 14

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element) › Inherent disclosureNot shown unpatentableNot shown unpatentable

    “We are unconvinced by Petitioner’s arguments and evidence. While we recognize that the range of claim 3 is very broad, and it is possible that scaffolds having fiber diameters as set forth in Johnson could have a mean pore size falling within the range, inherency “may not be established by probabilities or possibilities.” Par Pharm., Inc. v. Twi Pharms., Inc., 773 F.3d 1186, 1196 (Fed. Cir. 2014). Nor does Petitioner sufficiently explain why a person of ordinary skill in the art would have understood the process of Example 1 to necessarily result in the claimed mean pore size. We are also persuaded by Patent Owner’s argument that Boland 2005’s disclosure of a fiber diameter similar to Johnson’s that nevertheless falls outside the claimed mean pore size range. We note that Petitioner never addresses Boland 2005 in its Reply. 4. Conclusion as to Anticipation For these reasons, we find that Petitioner has met its burden of showing that claims 1, 2, 4, 5, and 13 are anticipated by Johnson, but has failed to meet its burden as to claim 3.” slip op. at 18

  Patent outcomesUS 10,632,228 mixed
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · Graham
  Patents in suitUS 10,632,228
• Reg Synthetic Fuels, LLC v. Neste OyjSome claims unpatentable
  PTAB · Feb 19, 2020 · IPR2018-01374 · APJ Christopher L Crumbley · IPR · Final written decision

  Claims 6, 7, 10, 20, and 24 are unpatentable; claims 1–5, 8, 9, 11–19, and 21–23 were not shown unpatentable, because the cited art did not teach the claimed iron-content limitation.

  RulingsFinal written decision

  • Skill levelSkill level board ownDecided for patent owner

    “Neste argues that REG’s proposed level of skill in the art is “unreasonably high” and instead proffers that “a person of ordinary skill in the field of biofuel engineering and processing as of Feb. 15, 2011 would have had a degree in chemical engineering or chemistry and at least two to three years of experience with processes for manufacturing hydrocarbons from bio renewable feedstocks.” PO Resp. 6–7 (citing Ex. 2029 ¶ 31). Neither party indicates that the outcome of any arguments made in this case would change depending on the level of ordinary skill in the art. We agree with the parties that the ordinarily skilled artisan, in February 2011, would have had at least a degree in chemical engineering or chemistry and would have had several years of experience in processing and refining biofuels. We need not parse the particular amount of education or experience given that neither party asserts this determination would have had any effect on the arguments or analysis in this case. Further, we find that the prior art of record reflects the level of skill in the art at the time of the invention. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for patent owner

    “We have again reviewed the record and the parties’ arguments, and again decline to import into the claim a requirement that the bio oil must be pre-treated. As we discussed in our institution decision, nothing in the ’185 patent indicates that the definition of bio oil is so limited. And we note that certain dependent claims of the ’185 patent, for example claim 21, specifically recite a pre-treatment step, leading to the conclusion that the bio oils of the independent claims are not limited to only pretreated bio oils. Neste’s new evidence introduced during trial is extrinsic to the patent, based on the testimony of Dr. Klein regarding the criticality of the iron content range. See PO Resp. 3 (citing Ex. 2029 ¶¶ 35–36, 38). In any event, we fail to see how the criticality of the claimed range mandates that the bio oil be pretreated prior to undergoing the claimed process. While Dr. Klein testifies that it is “clear from the ‘185 patent [that] a bio oil feed must be pretreated to render it suitable for commercial hydrotreatment” (Ex. 2029 ¶ 35), the portion of the patent he cites for this proposition states only that “bio-based feedstock (glyceride oil) to be used as feed material for hydrotreatment reaction can be purified to iron content of less than 1 to 0.2 w-ppm.” Ex. 1001, 4:50–55 (emphasis added). But this statement does not address the use of a bio oil that already contains an iron content within the claimed range, which therefore would not need purification. Indeed, the ’185 patent discusses “experiments with palm oil having very low level of impurities.” Ex. 1001, 4:45–46. Based on the foregoing, we maintain our view that the claim term requires no construction beyond its express language. The bio oil to be used in the method of claim 1 may be pretreated to achieve the claimed iron content, but pretreatment is not required by the claim.” slip op. at 11

  • Claim Construction › Intrinsic evidence (Phillips canons) › Preamble limiting or notPreamble not limitingDecided for petitioner

    “The intrinsic record of the ’185 patent contains no indication that bio oil intermediate was a new term coined to signify a specific class of bio oils, as Neste contends. The written description contains a section devoted to providing specific definitions for terminology, including “bio oil,” “glyceride oil,” and “hydrotreatment.” Ex. 1001, 3:28–4:7. There is no mention of a bio oil intermediate, which would be expected if the inventors had intended to coin a new term. The only use of “intermediate” in the entire written description is as follows: “disclosed is a glyceride oil intermediate, which intermediate consists of glyceride oil from at least one renewable source and the iron content of said glyceride oil is less than 1 w-ppm.” Id. at 4:64–67. The sentence preceding that one states only that the “purification result can be obtained (depending on used feedstock) using pretreatment methods.” Id. at 4:61–62 (emphasis added). As can be seen, there is no mention in this passage that the “glyceride oil intermediate” must be pretreated, and no indication it is a novel term coined by the inventors. In any event, Neste has not given us reason to depart from the general presumption that a claim preamble is not limiting. The body of claim 6 recites a structurally complete invention, defining the bio oil intermediate according to its iron content. There is no reason to rely on the preamble of the claim for any structure, or for antecedent basis for any claim term. Therefore, we conclude that the preamble does not “breathe life and meaning” into the claim, but rather recites an intended use for the structurally complete invention recited in the body of the claim. As such, we decline to adopt Neste’s modified construction of the claim term, and maintain our prior construction of claim 6’s preamble.” slip op. at 14

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableUnpatentableMixed

    “Upon evaluation of the record as a whole, we believe Neste has the better argument, and conclude that the iron content of the bio oil in claim 1 should be determined when the feed is introduced to the catalyst bed. This interpretation is, most importantly, reflected in the structure of the claim. Claim 1 contains a single process step, of “subjecting a bio oil . . . to a hydrotreatment process.” Immediately following this process step is a wherein clause that requires the iron content of “said bio oil” to be within a certain range. The necessary implication of this claim structure is that “said bio oil” is referring to the substance that is being subjected to the hydrotreatment process, meaning the iron content that is relevant to the claim is the iron content at the time of hydrotreatment with a catalyst. The claim, as a comprising claim, does not exclude the presence of other treatment steps such as purification or dilution, but the structure of the claim does imply that these additional steps should be performed prior to determining whether the iron content of the feed is within the claimed range.” slip op. at 20

  Patent outcomesUS 8,742,185 mixed
  Claim construction§ 102 anticipation§ 103 obviousness
  Patents in suitUS 8,742,185

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.