- Apple Inc. v. Corephotonics Ltd.All claims unpatentablePTAB · Apr 6, 2020 · IPR2019-00030 · APJ Monica S Ullagaddi · IPR · Final written decision
Claims 1–5 are unpatentable as obvious over Ogino and Beich; claims 1–4 are also unpatentable over Ogino alone, but claim 5 is not shown unpatentable on that ground.
RulingsFinal written decision- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner
“We construe claim terms to the extent necessary. See, e.g., Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 7
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed board ownDecided for patent owner
“supported by the cited evidence. We are persuaded, instead, that “the image plane and the sensor are taught by the ’568 patent to be coincident,” and “[t]hus, there is no ambiguity in the ’568 patent about where the image plane is located or that TTL is measured to the image plane,” as Petitioner argues in its Reply. Reply 13 (Ex. 1026 ¶ 5; Ex. 1003, 33–35). Patent Owner acknowledges as much, noting that “as these terms[, i.e., the image plane and the sensor,] are used in the specification of the ’568 patent, the image plane is the surface of the sensor.” Sur-reply 2. We find that the ’568 patent discloses that the electronic sensor corresponds to or is coincident with the image plane and thus, the TTL could be measured with respect to either the sensor (electronic or film) or the image plane and reach the same result. Based upon the complete trial record, we maintain our construction of TTL from the ’1140IPR and the ’1146IPR3, which encompasses “the length of the optical axis spacing between the object-side surface of the first lens element and one of: an electronic sensor, film, and an image plane corresponding to either the 3 The panel authorized, and the parties filed, supplemental briefing to address this construction before it was adopted in both the related ’1140IPR and ’1146IPR, and that the parties responded to this construction in the hearing in this proceeding (with citations to the transcript). See, e.g., Paper 28 (PO’s demonstratives), 5; ’1140IPR, Paper 31; ’1146IPR, Paper 30; see also Trial Practice Guide Update 13–14 (July 2019), https://www.uspto.gov/sites/default/files/documents/trial-practice-guide-update3.pdf; Hamilton Beach Brands, Inc. v. f’real Foods, LLC, 908 F.3d 1328, 1339 (Fed. Cir. 2018) (finding that the Board did not violate the Administrative Procedure Act when it adopted its own claim construction in the final decision because the parties had notice and an opportunity to be heard). electronic sensor or a film sensor.” See ’1140IPR, Paper 37, 18; ’1146IPR, Paper 37, 14.” slip op. at 14
- Skill levelSkill level patent owner adoptedDecided for patent owner
“Even assuming, arguendo, we were to credit Patent Owner’s expert testimony as to the disjointed nature of optical lens assembly design experience and manufacturing experience, we are not persuaded that a person of ordinary skill in the art at the time of the invention having only design experience would be so completely unaware of manufacturing considerations so as to preclude taking into account the very general guidance of Beich. See Reply 24–25. Beich teaches that a lens designer should have a basic understanding of the manufacturing process, which would include the limits for fabricating lens elements in an optical lens assembly. Ex. 1020, 7. We are persuaded that the information conveyed in Beich would have been understood, known, and applied by the ordinarily skilled lens designer (see Reply 4–6 (citing Ex. 2014, 4, 9, 11, Fig. 9.2)), irrespective of whether such person had manufacturing experience. Stated differently, although an ordinarily skilled designer of an optical lens assembly may not have had any real-world manufacturing experience, we are persuaded that such person would still have taken into account manufacturing concerns. Although there are differences between the definitions proposed, our conclusions rendered in this decision do not turn on selecting a particular definition for the level of ordinary skill in the art, for the reasons discussed above. We determine, on this record, that the level of ordinary skill proposed by Patent Owner is consistent with the ’568 patent and the asserted prior art. We agree with Patent Owner’s proposal regarding the level of ordinary skill except for Patent Owner’s arguments about manufacturing discussed above. As such, we adopt Patent Owner’s proposal.” slip op. at 18
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentable
“As noted by Petitioner, The Handbook of Optics discloses that “[i]n the case of both negative and positive lens elements, it is good policy to avoid element forms wherein the center-to-edge thickness ratio exceeds three for positive elements.” Ex. 1019 § 34.15. Thus, we are persuaded by Petitioner’s fourth reason that the cited disclosure provides evidence that the ordinarily skilled artisan would have selected a particular diameter for the first lens element disclosed in Ogino in conformance with manufacturing considerations known to the ordinarily skilled artisan. We are further persuaded that, from the selection of that particular diameter, a Z1 value for the object-side surface and a Z2 value for image-side surface at the minimum usable edge of the first lens element can be obtained and, in turn, circumferential edge thickness L1e can be obtained. Pet. 35–36 (citing Ex. 1003, 42; Ex. 1005, 15:1–3). We are further persuaded by Petitioner’s supporting reasoning that “a POSITA would understand the manufacturing benefits of maintaining the lowest possible center-to-edge thickness ratio since ‘the preferred shape of a molded element is one that has fairly uniform thickness.’” Id. at 42 (quoting Ex. 1018, 92) (citing Ex. 1003, 48). Based on our review of the complete record, we find that the record supports Petitioner’s contentions concerning claim 1. Petitioner demonstrates by a preponderance of the evidence that claim 1 is unpatentable as obvious over Ogino.” slip op. at 37
Patent outcomesUS 9,857,568 unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 9,857,568 - Apple Inc. v. Corephotonics Ltd.All claims unpatentablePTAB · Dec 3, 2019 · IPR2018-01140 · APJ Marc S Hoff · IPR · Final written decision
Claims 1 and 13 are unpatentable as anticipated by Ogino; claims 14 and 15 are unpatentable as obvious over Ogino and Chen II.
RulingsFinal written decision- BurdenFwd all claims unpatentableUnpatentable
“claims 1 and 13 of the ’032 Patent are anticipated by Ogino. Petitioner has also demonstrated, by a preponderance of the evidence, that claims 14 and 15 of the ’032 Patent are unpatentable over the combination of Ogino and Chen II. The chart below summarizes our conclusion. References Claims Claims Claims 35. Shown Not shown Challenged U.S.C. Unpatent- Unpatentable able Ogino 1 and 13 1 and 13 § 102 Ogino, Chen 14 and 15 14 and 15 § 103 II 1 and 13-15” slip op. at 40
- Skill levelSkill level board ownDecided for petitioner
“that Ogino and Chen II disclose substantially different lens systems. PO Resp. 36. As Petitioner points out, both Ogino and Chen II describe mobile phone camera systems with all lenses being aspheric; a first lens with a meniscus shape with positive refractive power; a second lens with negative refractive power; a third lens with a meniscus shape and with a negative refractive power; a fourth lens with a meniscus shape with positive refractive power; and a fifth lens with a meniscus shape and with a negative refractive power. Pet. Reply 22; Pet. 41–44. We agree with Petitioner that such a skilled artisan, possessing an applicable college degree, approximately three years experience in designing multi-lens optical systems, “experience in analyzing, tolerancing, adjusting, and optimizing multilens systems, and experience with lens design software such as CodeV, Oslo, or Zemax,” would have the appropriate knowledge to perform routine modifications to a lens design. Pet. Reply 24; Pet. 7; PO Resp. 12. Patent Owner’s expert Dr. Moore testified that such a skilled artisan “would be able to use the computer program [i.e. CodeV or Zemax] to optimize lens designs.” Pet. Reply 24; Ex. 1025, 29:25–30:9. Dr. Moore testified that the skilled artisan would “tell the [lens design] program that you want to vary certain parameters of a lens . . . . And then the program, through a fairly complicated algorithm, then actually goes through and varies them and determines how to make a better lens. You determine as a lens designer what you’re trying to improve.” Ex. 1025, 28:13–23.” slip op. at 38
- Expert testimonyPatent owner expert discountedDecided for petitioner
“We are unpersuaded by Patent Owner’s argument that the skilled artisan would have understood that third, fourth, and fifth lenses also contribute to vignetting in Ogino. PO Resp. 38. We credit Petitioner’s argument that Dr. Moore’s conclusion regarding vignetting in the third, fourth, and fifth lenses is unreliable because it is based on assumptions not specified in Ogino. Pet. Reply 16; Ex. 1026 ¶ 11. For example, Ogino does not provide lens diameters or vignetting apertures for the lens assembly of Example 6 that would vignette the light beams on the third, fourth or fifth lens elements. Pet. Reply 17; Ex. 1026 ¶ 11. Additionally, Dr. Sasián testifies that vignetting is a result of the second lens. Pet. Reply 17–18; Pet. 54; Ex. 1003, 59.” slip op. at 36
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed petitioner constructionDecided for petitioner
“Effective Focal Length (EFL) Petitioner asserts that while the specification of the ’032 Patent does not offer an express definition for the term “effective focal length,” “its meaning is well known in the art, as exemplified in Li (Ex. 1007), which states that “[t]he focal length of a lens assembly [is] also referred to as the effective focal length [(]EFL).” Pet. 9–10 (internal parentheses omitted); Ex. 1007, 2:59–61. Patent Owner, in response, does not dispute Petitioner’s construction of “effective focal length,” stating that the Petition does not turn on the construction of the term. PO Resp. 20. Having reviewed the evidence of record, we agree with Petitioner that Li supports construing the term “effective focal length” as “the focal length of a lens assembly.” We adopt this construction.” slip op. at 10
Patent outcomesUS 9,402,032 unpatentableClaim construction§ 102 anticipation§ 103 obviousnesscites KSR · GrahamPatents in suitUS 9,402,032
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.