- CQV Co., Ltd. v. Merck Patent GmbHNo claims unpatentablePTAB · Oct 14, 2025 · PGR2021-00054 · APJ Kristina M Kalan · PGR · Remand
Claims 1–22 were not shown unpatentable because Sample C was not proven publicly available as prior art, and the original decision found the remaining grounds insufficient.
RulingsRemand decision- Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication not establishedNot shown unpatentable
“We agree with Patent Owner that Petitioner’s evidence in Kuntz (Ex. 1026), the Annual Report (Ex. 1028), Masuko (Ex. 1029), and Pfaff (Ex. 1034) is insufficient to show that Xirallic® Sample C was available to the public before the effective filing date of the ’861 patent. Petitioner has not asserted, nor do we find, that any of these documents refer to or describe the lot of Xirallic® from which Sample C was taken. See Final Dec. 26. Kuntz, the Annual Report, Masuko, and Pfaff may support a finding that the Xirallic® line of products was available to the public, but these documents do not support a finding that the lot of Xirallic® from which Sample C was taken was available to the public. We also agree with Patent Owner that the Technical Data Sheets (Exs. 1005–1010), Certificates of Analysis (Exs. 1011–1017), and Material Safety Data Sheet (Ex. 1025) are insufficient to show that Xirallic® Sample C was available to the public. Petitioner has not asserted, nor do we find, that any of these documents refer to or describe the lot of Xirallic® from which Sample C was taken. See Final Dec. 26–27. Regardless of how the Technical Data Sheets were used in the Opposition against the European counterpart of the ’861 patent (Exs. 1040, 1041) and during the prosecution of the application from which the ’861 patent issued (Ex. 1003, 102–104), the Technical Data Sheets do not refer to or describe the lot of Xirallic® from which Sample C was taken. Moreover, as noted by Patent Owner, the Technical Data Sheets (Exs. 1005–1010) indicate that they are “preliminary” and Petitioner has not provided any evidence that the Technical Data Sheets were ever issued to the public, as opposed to just issued internally. See PO Resp. 18–19. We also find persuasive Patent Owner’s argument that the Technical Data Sheets are preliminary because other, later-dated technical data sheets (Exs. 2012, 2013) lack the “preliminary” label and list characteristics that are different from those in Exhibits 1005–1010. See PO Resp. 19 (comparing, e.g., Ex. 1009 and Ex. 2013; Ex. 1005 and Ex. 2012). The Technical Data Sheets may support a finding that the Xirallic® products they describe existed as of the dates on the documents, but they do not support a finding that the lot of Xirallic® from which Sample C was taken was available to the public.” slip op. at 20
- Expert testimonyPetitioner expert discountedPatent owner expert creditedOther
“witnesses. See Elbit Systems of Am., LLC v. Thales Visionix, Inc., 881 F.3d 1354, 1358 (Fed. Cir. 2018) (citing Trs. of Columbia Univ. v. Illumina, Inc., 620 F. App’x 916, 922 (Fed. Cir. 2015); Inwood Labs., Inc. v. Ives Labs., Inc., 456 U.S. 844, 856 (1982)). We have reviewed the witness testimony in the record and, more particularly, Mr. Choi’s deposition answers regarding Petitioner’s purchase of the lot of Xirallic® from which Sample C came. We find that Mr. Choi’s responses cast doubt on the credibility of his declaration testimony, namely with regard to the public availability of Sample C. Mr. Choi represented that he was involved in the purchase of the lot of Xirallic® from which Sample C was taken. Ex. 2011, 48:1–23. Mr. Choi stated that he instructed Petitioner’s marketing team manager to buy the sample from a distributor of Patent Owner’s products located in Europe. Id. at 48:24–49:4. Mr. Choi stated that he has evidence of the transaction, but refused to reveal the name of the company from which Petitioner purportedly purchased the lot of Xirallic® (id. at 49:5–50:3) and refused to produce an email in his possession that would corroborate his testimony regarding Petitioner’s acquisition of the product (id. at 50:8–16, 51:10–23). Mr. Choi represented that he does not remember how much Petitioner paid for Sample B. Id. at 56:4–5. Mr. Choi admitted that the entity from which Petitioner acquired the lot of Xirallic® from which Sample C was taken is “not currently a Merck distributor” (Ex. 2011, 50:4–7) and was not “a Merck distributor at the time” that “samples B and C were purchased” (id. at 51:25–52:2). According to Mr. Choi, the company is a “former distributor” of Patent Owner’s products. Id. at 52:3–6. Mr. Choi did not know, according to his testimony, when that unnamed entity first obtained the lot of Xirallic® (id. at 52:7–10) and he stated that he did not have personal knowledge of how the entity obtained the lot of Xirallic® (id. at 52:12–19). Instead, Mr. Choi assumed the entity was “able to obtain the sample through the routine course or process” the entity uses “to take samples or get samples.” Id. at 52:12–19. Mr. Choi believed the sample of Xirallic® from which Sample C was taken was sealed when Petitioner received it because samples from dealers are sealed, and he remembered observing that the package was from a dealer. Id. at 52:24– 54:25. However, Mr. Choi admitted that he did not obtain a technical data sheet or certificate of analysis for the lot of Xirallic® from which Samples B and C were taken. Id. at 59:6–11. Mr. Choi also answered questions regarding Petitioner’s purchase of Samples D and H. Ex. 2011, 62:20–66:8, 67:7–9, 73:12–13, 73:17–22. Similar to his testimony regarding Samples B and C, Mr. Choi admitted withholding an email regarding the purchase of the lot of Xirallic® from which Sample D was taken. Id. at 62:20–63:9. Mr. Choi also admitted that he did not know how Akzo USA or Axalta obtained the Xirallic® the companies sold to him, and admitted that Akzo USA was not a distributor of Patent Owner’s products at the time Petitioner purchased the product. Id. at 63:10–66:8, 73:17–22. Mr. Choi also admitted that Petitioner did not pay Akzo USA for the lot of Xirallic® from which Sample D was taken, and did not pay Axalta for the lot of Xirallic® from which Sample H was taken. Id. at 67:7–9, 73:12–13. Although Petitioner presents declaration testimony from Mr. Choi representing that he purchased the lot of Xirallic® from which Samples B and C were taken in October 2011 (Ex. 1004 ¶ 16), Mr. Choi’s declaration testimony lacks corroborating evidence, and his deposition testimony does not support that the product was available to the public, as we found in our Final Written Decision. See Final Dec. 27–28. Notably, Petitioner produced corroborating evidence for Mr. Choi’s acquisition of Samples A, H, and I. See Ex. 1004 ¶¶ 13 (citing Ex. 1047), 18 (citing Exs. 1024, 1025). However, Mr. Choi withheld similar evidence for the Xirallic® lots from which Samples B, C, and D were taken. See Ex. 2011, 50:8–16, 51:10–23, 62:20– 63:9; Final Dec. 28. As Patent Owner argues, there is “no information to determine when a contract was established, that there was consideration for the exchange, that the product was available to be delivered when the alleged transaction took place, or even when the product was delivered. Choi has no memory of what was paid for the product.” Sur-Reply 24–25; see also PO Resp. 13–14; PO Br. Rem. 2–4.” slip op. at 34
- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable
“Based on the evidence discussed above, we are not persuaded that Petitioner has shown by a preponderance of the evidence that Sample C was available to the public. Regardless of whether a company avoids wasting shelf life of its products (Ex. 1004 ¶¶ 15–16), there is no persuasive evidence in the record showing that the lot of Xirallic® from which Sample C was taken was released from quality control and then made available to the public by Patent Owner. Mr. Choi’s testimony shows that Petitioner obtained the lot of Xirallic® from which Sample C was taken in an atypical manner (i.e., not from Patent Owner or one of Patent Owner’s current distributors) (Ex. 2011, 49:5–50:7, 50:8–16, 51:10–23, 51:25–52:6, 52:12– 19), and there is no evidence in the record to show that the lot of Xirallic® was intended for sale, rather than for experimental use only or for some other restricted use. Accordingly, we determine Petitioner has not demonstrated by a preponderance of the evidence that Sample C qualifies as prior art against the ’861 patent, and we determine that Petitioner has not shown by a preponderance of the evidence that the ’861 patent is unpatentable over the grounds relying on Sample C.” slip op. at 38
Patent outcomesUS 10,647,861 not shown unpatentable§ 102 anticipation§ 103 obviousnessPatents in suitUS 10,647,861 - Tanklogix, LLC v. Sitepro, Inc.Institution deniedPTAB · Oct 10, 2025 · IPR2025-00652 · APJ Bart A Gerstenblith · IPR · Institution
The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–23 and 25–30 were unpatentable over the asserted grounds.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsDenied
“presented in the petition . . . and any [preliminary] response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a) (2024). For the reasons given below, on this record Petitioner has not established a reasonable likelihood that it would prevail in showing the unpatentability of any of the Challenged Claims. Accordingly, we do not institute an inter partes review.” slip op. at 2
- Skill levelSkill level patent owner adoptedDecided for patent owner
“The parties’ proposed levels of ordinary skill in the art are similar, although Patent Owner proposes two years of experience along with a bachelor’s degree whereas Petitioner proposes “significant” experience. Patent Owner also proposes an alternative with more extensive experience in lieu of a bachelor’s degree. Although we find Petitioner’s proposed qualifications acceptable, we adopt Patent Owner’s proposed qualifications for the purposes of this Decision because they offer a wider range of qualifications that nonetheless comport with the level of ordinary skill necessary to understand and implement the teachings of the ’403 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001); In re GPAC Inc., 57 F.3d 1573, 1579 (Fed. Cir. 1995); In re Oelrich, 579 F.2d 86, 91 (CCPA 1978). Our analysis and findings herein, however, do not turn on any differences in the parties’ proposed qualifications.” slip op. at 12
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“The parties assert that each claim term should be construed in accordance with its plain and ordinary meaning. Pet. 10; Prelim. Resp. 4 (citing Ex. 2009 ¶ 73); see Ex. 1002 ¶ 22 (opining the same). And, in the respective claim construction sections of their briefs, the parties do not propose any claim terms for express construction. We agree with the parties that no claim terms require express construction to resolve the controversy before us. See Realtime Data, 912 F.3d at 1375.” slip op. at 13
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable
“We agree with Patent Owner that the Petition fails to demonstrate that Kahn discloses element [1.2] because the evidence cited does not disclose a “first computer system being configured to provide remote control of the first pump or first valve” (i.e., a fluid-handling device). Kahn is directed to providing access to fluid sensing data and analyzing and providing visual information on that data, but Petitioner has not identified any disclosure of the capability to remotely control fluid-handling devices. See, e.g., Ex. 1005, code (54), 1:27–36, 2:50–3:2. More specifically, Kahn’s disclosures that Petitioner relies on for allegedly teaching remote control are deficient. We discuss each. First, Petitioner points to the following, “[f]or instance, as illustrated in FIG. 1C, a fluid control device such as a valve 15A is located on the input side of a sen[s]or unit 110.” Ex. 1005, 8:19–21, cited in Pet. 13. This portion of Kahn, however, does not disclose remote control. Second, Petitioner cites to the following: Finally, or in addition to, the communication unit 112B can include on-site alerts such as optical (indicator lights), audible alerts (e.g., alarm sounds), tactile (e.g., vibration of the unit) or can be interfaced to an appropriate control valve for simply shutting off the supply of fluid upon the detection of emergency events, for instance. Pet. 13 (citing Ex. 1005, 10:62–67). We agree with Patent Owner that this portion of Kahn teaches on-site alerts and local control of the fluid-handling device. See Prelim. Resp. 7. This portion of Kahn does not disclose remote control.” slip op. at 18
Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,294,403 - Tanklogix, LLC v. Sitepro, Inc.Institution deniedPTAB · Oct 10, 2025 · IPR2025-00651 · APJ Bart A Gerstenblith · IPR · Institution
The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–3, 6, 7, and 9–20 were unpatentable over any asserted ground.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsDenied
“presented in the petition . . . and any [preliminary] response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a) (2024). For the reasons given below, on this record Petitioner has not established a reasonable likelihood that it would prevail in showing the unpatentability of any of the Challenged Claims. Accordingly, we do not institute an inter partes review.” slip op. at 2
- Skill levelSkill level patent owner adoptedDecided for patent owner
“The parties’ proposed levels of ordinary skill in the art are similar, although Patent Owner proposes two years of experience along with a bachelor’s degree whereas Petitioner proposes “significant” experience. Patent Owner also proposes an alternative with more extensive experience in lieu of a bachelor’s degree. Although we find Petitioner’s proposed qualifications acceptable, we adopt Patent Owner’s proposed qualifications for the purposes of this Decision because they offer a wider range of qualifications that nonetheless comport with the level of ordinary skill necessary to understand and implement the teachings of the ’680 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001); In re GPAC Inc., 57 F.3d 1573, 1579 (Fed. Cir. 1995); In re Oelrich, 579 F.2d 86, 91 (CCPA 1978). Our analysis and findings herein, however, do not turn on any differences in the parties’ proposed qualifications.” slip op. at 11
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner
“target value” is part of a command that is sent from a computing device to a server and then to a controller. The controller then receives a measurement of the fluid by a sensor and determines whether the measurement satisfies the “target value.” If the measurement does not satisfy the “target value,” further operations are undertaken. The recited operation sequence makes clear that the plain and ordinary meaning of “target value” is not as Dr. Wooley opines because the particular operating condition that a device is in at a particular time is represented by the measurement taken by the sensor, 11 Some claim language less relevant to construing “target value” was omitted for ease of reference. which the controller then uses to determine whether the measurement satisfies the “target value.” Additionally, claim 1 recites that the “target value” is sent as part of a command to the controller. The “target value” is not sent to the controller from the sensor, as might be expected if the plain and ordinary meaning of “target value” were as Dr. Wooley opines. Petitioner and Dr. Wooley’s construction would also result in “target value” meaning effectively the same thing as the measurement of the fluid by the sensor, a concept that is separately recited in claim 1 and to which the “target value” is compared. The Specification of the ’680 patent does not support Petitioner’s understanding of the plain and ordinary meaning of “target value.” Although the Specification does not recite “target value,” it recites “target state,” and describes “target state” sufficiently to understand the plain and ordinary meaning of “target” as used in “target value” and “target state.” In particular, the ’680 patent explains that “[i]n some embodiments, the process 104 includes receiving, via a network interface, from a remote user device, (e.g., via a command-center server) a command to change a state of a fluid-handling device to a target state.” Ex. 1001, 11:48–51. This portion reflects that the command is seeking to change a state of a fluid-handling device to a target state. In other words, the “target value” or “target state” is not generally “the particular operating condition that a device is in at a particular time”; rather, it is a value or state that the fluid-handling device is desired to be in, as Patent Owner and Dr. Durham explain. Additionally, just as claim 1 recites a directional component for the “target value” to be sent to the controller in a command, so too does the Specification describe a “target state” as being sent in a command from a remote user device. Thus, the Specification clearly supports the plain and ordinary meaning proposed by Patent Owner and Dr. Durham and not the plain and ordinary meaning proposed by Petitioner and Dr. Wooley. slip op. at 14
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable
“time-stamped process data, report exception therein to the remote host, and extract and transmit time-stamped process data to the remote host.” Ex. 1005, Abst. (emphases added). Almadi explains that its remote field systems must include a plurality of controller units “to issue commands to, and gather and process data from a plurality of field devices, including remote systems and instruments, . . . [and] a database server for the storage of process data retrieved from the remote subsystems and instruments.” Id. at 2:22–30 (emphases added). Based on these disclosures, we agree with Patent Owner that Petitioner has not established that Almadi discloses element [1.4]. Specifically, the teachings from Almadi identified by Petitioner refer to process data, which is data retrieved from the remote subsystems/field devices. Thus, we understand that Almadi’s teaching—of using an Ethernet switch to transmit “process data”—describes transmitting data from the remote subsystems/field devices. See Ex. 1005, 3:13–17, cited in Pet. 15. But claim 1 and particularly element [1.4], recites “sending, with the server, the target value to the network address [which identifies a controller of the fluid-handling device13] via the network,” which is different than sending process data from the field devices to the remote host or database server for storage.” slip op. at 19
Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,175,680 - Tanklogix, LLC v. SiteproInstitution deniedPTAB · Oct 10, 2025 · IPR2025-00650 · APJ Sheila F Mcshane · IPR · Institution
The Board denied institution because Petitioner did not show a reasonable likelihood that claims 18–32 and 34 were unpatentable over Kahn or Kahn and Gutierrez.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied
“information presented in the petition . . . and any response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a) (2024). Upon consideration of the Petition, the Preliminary Response, and the evidence of record, we determine that Petitioner has not established a reasonable likelihood of prevailing with respect to the unpatentability of at least one claim of the ’871 patent. Accordingly, for the reasons that follow, we decline to institute an inter partes review of claims 18–32 and 34 of the ’871 patent.” slip op. at 2
- Skill levelSkill level patent owner adoptedDecided for patent owner
“The respective proposed levels of qualifications for a person of ordinary skill in the art are similar, with Patent Owner proposing two years of experience compared to Petitioner proposing significant experience with remotely controlling fluid-handling devices, like SCADA systems. Patent Owner also proposes more extensive experience in lieu of educational experience. While we find Petitioner’s proposed qualifications to be acceptable, we adopt Patent Owner’s proposed qualifications for the purposes of this Decision because they offer a wider range of qualifications that nonetheless comport with the level of skill necessary to understand and implement the teachings of the ’871 patent and the asserted prior art. Our analysis and findings herein, however, do not turn on any differences in the qualifications adopted.” slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“We determine that we need not expressly construe any claim terms to resolve the parties’ disputes on the current record. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 10
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable
“actuators and the remote control of fluid handling devices, including the receipt with the user-interface module of “a user command to actuate an actuator via a presented control interface” (limitation [18.7]) and “account authorized to send commands to remotely control fluid handling devices” (limitation [18.11]). We agree with Patent Owner that the Petition fails to demonstrate that Kahn discloses or teaches these limitations because the evidence does not provide support that there is remote control of fluid handling devices or the use of a user command on a control interface to send a command to a fluid handling device, for instance. Kahn is directed to providing access to fluid sensing data and analyzing and providing visual information on that data, but we do not discern that it teaches or discloses the capability to remotely control fluid handling devices. See, e.g., Ex. 1005, code (54), 1:27–36, 2:50–3:2. More specifically, the Kahn disclosures that Petitioner repeatedly relies upon for allegedly teaching this control are deficient. See Ex. 1005, 10:62–67, 14:35– 15:2, 15:62–16:32; see also Pet. 12–14, 16–18. Kahn discloses that “the communication unit 112B can include on-site alerts such as optical (indicator lights), audible alerts (e.g., alarm sounds), tactile (e.g., vibration of the unit) or can be interfaced to an appropriate control valve for simply shutting off the supply of fluid upon the detection of emergency events, for instance.” Ex. 1005, 10:62–67. Communication unit 112B is part of the local “sensor unit,” wherein the detection conditions determined by the sensor are communicated to remote devices by communication unit 112B. See id. at 3:31–33, 5:62–6:2, 6:27–35, 7:33–37, 13:7–12, Figs. 1A–1C. Kahn discloses that the sensor units, which include communication units 112B, can be located near shut-off valves and can communicate with distant locations. See id. at 11:1–13. There are no disclosures, however, in the above passages that there is remote control of fluid handling devices, that there is a user command on a control interface that actuates an actuator, or that there is a command sent to the facility actuators via a network connection, as required in limitations [18.5]–[18.7] and [18.9]–[18.12], respectively. Rather, the disclosure indicates that the communication unit 112B includes on-site alerts and that the local (non-remote) communication unit 112B can be interfaced with the control valve.” slip op. at 18
Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,488,871 - Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing deniedPTAB · Oct 7, 2025 · IPR2024-01462 · APJ Jo-Anne M Kokoski · IPR · Rehearing
The Board denied Solus’s rehearing request, leaving institution denied for claims 1–8 because the petition did not adequately show motivation to combine Hanafusa and Dobashi.
RulingsRehearing decision- RehearingRehearing, deniedDenied
“of the decision de novo, but instead review the decision for an abuse of discretion. 37 C.F.R. § 42.71(c). An abuse of discretion may be determined “if a decision is based on an erroneous interpretation of law, if a factual finding is not supported by substantial evidence, or if the decision represents” slip op. at 2
- Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable
“In particular, neither Petitioner nor Dr. Josefowicz adequately explain why a POSITA looking for ways to make Hanafusa’s surface roughness low-profile would look to methods to achieve Dobashi’s RSm values. Dobashi teaches that because RSm “can be adopted as the period of waviness, RSm can also be used as an indicator for judgment of the surface.” Ex. 1005, 2:66–3:1, 6:23–26. Dobashi explains that waviness is “an indicator for determining whether the fine pattern forming performance is good or bad,” and “[t]he surface has small waviness and is smooth when RSm is large, and the surface has large waviness Dobashi also teaches that surface roughness Rzjis is used as a low-profile indicator. Ex. 1005, 2:66–3:1. Dobashi, therefore, teaches that RSm is an indicator of surface waviness, which Dobashi explains is different than surface roughness. Id. at 2:66– 3:3, 6:23–29. Given these teachings in Dobashi, neither Petitioner nor Dr. Josefowicz sufficiently explains how or why a POSITA would have been motivated to implement Dobashi’s RSm values to make Hanafusa’s surface roughness low-profile. See Pet. 10–12; Ex. 1003 ¶¶ 46–52.” slip op. at 4
§ 103 obviousnessPatents in suitUS 11,346,014 - Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing deniedPTAB · Oct 7, 2025 · IPR2024-01461 · APJ Jo-Anne M Kokoski · IPR · Rehearing
The Board denied rehearing and left in place its denial of institution because Petitioner did not show that claims 1–10 were likely obvious over the asserted combinations.
RulingsRehearing decision- RehearingRehearing, deniedDenied
“II. STANDARD OF REVIEW When rehearing a decision on institution, we do not review the merits of the decision de novo, but instead review the decision for an abuse of discretion. 37 C.F.R. § 42.71(c). An abuse of discretion may be determined “if a decision is based on an erroneous interpretation of law, if a factual finding is not supported by substantial evidence, or if the decision represents an unreasonable judgment in weighing relevant factors.” Arnold Partnership v. Dudas, 362 F.3d 1338, 1340 (Fed. Cir. 2004) (citing In re 1 US 2013/0108922 A1, published May 2, 2013 (Ex. 1004, “Shinozaki”). 2 G. Khatibi, Temperature Dependent Elastic and Thermal Properties of Thin Copper Foils, Copper; Proceedings of the International Conference Copper ’06 (2006) (Ex. 1006, “Khatibi”). 3 Korean Patent Pub. No. 10-2012-0003485, published Jan. 10, 2012 (Ex. 1013; Ex. 1014 (English translation), “Toshio”). 4 US 2013/0108887 A1, published May 2, 2013 (Ex. 1012, “Kim”). 5 Griesi, M.B., Characterization of Electrodeposited Copper Foil Surface Roughness for Accurate Conductor Power Loss Modeling (2014) (Master’s Thesis, University of South Carolina) (Ex. 1015, “Griesi”). rehearing has the burden to show that the decision should be modified. 37 C.F.R. § 42.71(d). Additionally, the request for rehearing “must specifically identify all matters the party believes the Board misapprehended or overlooked, and the place where each matter was previously addressed in a motion, an opposition, or a reply.” Id.” slip op. at 2
- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Not shown unpatentable
“For example, Dr. Randall does not provide adequate explanation or objective evidence to support his opinion that Khatibi’s use of a laser speckle based dilatometer instead of the claimed thermomechanical analyzer “is unlikely to significantly impact the CTE[6] value” because “variations in equipment and a heating speed of 5° C/min would not significantly alter the results.” Ex. 1003 ¶ 58. In particular, Dr. Randall neither explains what constitutes a “significant” impact on CTE, nor provides objective evidence to support his contention that equipment variations and heating differences would not “significantly alter” the resulting measurements. And although Dr. Randall opines that “the heating rate (5°C per minute) is typical for certain devices” such as a thermomechanical analyzer or dilatometer, and “[t]ypically, these devices use temperature ramp rates between 2°C and 20°C per minutes, so the ‘5° C./min’ recited in [1d] is common and should not drastically affect the measurement results,” Dr. Randall fails to point us to any evidence showing that these temperatures are “typical” or that the claimed heating rate is “common.” Id. ¶ 59 (emphases added).” slip op. at 4
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable
“Petitioner, however, does not adequately explain why a POSITA would have been motivated to modify Kim’s copper foil surface to have a Pc value of 19.2 as reported in Griesi. In particular, neither Petitioner nor Dr. Randall points us to, nor do we discern, any teaching in Griesi that a peak count of 19.2 provides any particular benefits or properties that would have lead a POSITA to modify Kim’s copper foil surface as Petitioner proposes. Instead, Petitioner’s arguments that a POSITA would have been motivated to modify Kim’s copper foil surface with Griesi’s peak count patent itself. See KSR Int’l Co. v. Teleflex Inc., 550 U.S. 398, 421 (2007) (stating that the fact finder must be aware “of the distortion caused by hindsight bias and must be cautious of arguments reliant upon ex post reasoning”). It was Petitioner’s burden to establish that the combined teachings Kim and Griesi disclose limitation [1g] as proposed. We are not persuaded that we misapprehended Petitioner’s argument when we determined that Petitioner did not meet that burden.” slip op. at 8
- BurdenDecided for patent owner
“It was Petitioner’s burden to establish the Khatibi, alone or in combination with Shinozaki, Toshio, and Kim, discloses limitation [1d]. We concluded that Petitioner failed to meet that burden for the reasons explained in our Decision. We are not persuaded that we overlooked or misapprehended Khatibi’s disclosures, or Petitioner’s evidence and explanation thereof, in doing so.7” slip op. at 5
§ 103 obviousnesscites KSRPatents in suitUS 10,811,689 - Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Institution deniedPTAB · Apr 25, 2025 · IPR2024-01462 · APJ Jo-Anne M Kokoski · IPR · Institution
The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–8 were unpatentable under the asserted obviousness grounds.
RulingsInstitution decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“experience working on the development of materials or components for electronic devices such as batteries.” Pet. 2. Petitioner further contends that “[a]dditional education, such as a graduate degree, could compensate for less work experience, and additional work experience could compensate for less formal education.” Id. Patent Owner states that, “[f]or purposes of this Preliminary Response, Patent Owner applies Petitioner’s level of skill for a person of ordinary skill in the art.” Prelim. Resp. 4. For purposes of this Decision, we adopt Petitioner’s undisputed proposed definition because it appears to be consistent with the cited prior art and the disclosure of the ’014 patent. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (explaining that specific findings regarding ordinary skill level are not required “where the prior art itself reflects an appropriate level and a need for testimony is not shown” (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163 (Fed. Cir. 1985))).” slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“customary meaning of such claim as understood by one of ordinary skill in the art and the prosecution history pertaining to the patent.” 37 C.F.R. § 42.100(b). Under this standard, claim terms are generally given their plain and ordinary meaning as would have been understood by a person of ordinary skill in the art at the time of the invention and in the context of the entire patent disclosure. Phillips v. AWH Corp., 415 F.3d 1303, 1313 (Fed. Cir. 2005) (en banc). Only those terms in controversy need to be construed, and only to the extent necessary to resolve the controversy. Realtime Data LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019). in this proceeding.” Pet. 3. Patent Owner contends that “[t]he Board need not construe any term in order to determine that institution should be denied.” Prelim. Resp. 4. Based on the record before us, we determine that no claim term requires express construction for purposes of this Decision. See Realtime Data, 912 F.3d at 1375.” slip op. at 8
- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied
“For these reasons, we are not persuaded that Petitioner sufficiently establishes that a POSITA would have been motivated to modify Hanafusa in light of Dobashi with a reasonable expectation of success as Petitioner contends. Accordingly, we determine that Petitioner fails to demonstrate a reasonable likelihood of prevailing in its assertion that the subject matter of claim 1, and claims 4 and 8 that depend therefrom, would have been obvious over the combined teachings of Hanafusa and Dobashi.” slip op. at 18
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable
“Petitioner also focuses on Hanafusa’s teaching that all known methods can be used to make a rough surface low-profile, and Dobashi’s teaching that RSm can be used as an indicator for judgment of the surface, to support its contention that a POSITA would have been motivated to apply Dobashi’s RSm to further achieve Hanafusa’s purpose, without explaining how and why that would be the case. In particular, neither Petitioner nor Dr. Josefowicz adequately explain why a POSITA looking for ways to make Hanafusa’s surface roughness low-profile would look to methods to achieve as the period of waviness, RSm can also be used as an indicator for judgment of the surface.” Ex. 1005, 2:66–3:1, 6:23–26. Dobashi explains that waviness is “an indicator for determining whether the fine pattern forming performance is good or bad,” and “[t]he surface has small waviness and is smooth when RSm is large, and the surface has large waviness and is rough when RSm is small.” Id. at 3:1–3, 6:27–29. Dobashi also teaches that surface roughness Rzjis is used as a low-profile indicator. Ex. 1005, 2:66– 3:1. Dobashi, therefore, teaches that RSm is an indicator of surface waviness, which Dobashi explains is different than surface roughness. Id. at 2:66–3:3, 6:23–29. Given these teachings in Dobashi, neither Petitioner nor Dr. Josefowicz sufficiently explains how or why a POSITA would have been motivated to implement Dobashi’s RSm values to make Hanafusa’s surface roughness low-profile. See Pet. 10–12; Ex. 1003 ¶¶ 46–52.” slip op. at 14
Claim construction§ 103 obviousnesscites Phillips · KSRPatents in suitUS 11,346,014 - Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Institution deniedPTAB · Apr 23, 2025 · IPR2024-01461 · APJ Jo-Anne M Kokoski · IPR · Institution
The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–10 were unpatentable over either asserted § 103 ground.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied
“Institution of an inter partes review is authorized by statute when “the information presented in the petition . . . and any response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314 (2018); see also 37 C.F.R. § 42.4 (2023). For the reasons discussed below, we deny the Petition and do not institute an inter partes review.” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“II. ANALYSIS A. Level of Ordinary Skill in the Art Petitioner contends that a person of ordinary skill in the art (“POSITA”) “would have had at least an undergraduate degree in materials science, chemical engineering, electrical engineering, or related field, or equivalent knowledge, training, or experience, with at least two years of experience working on the development of materials or components for electronic devices such as batteries.” Pet. 4. Petitioner further contends that “[a]dditional education, such as a graduate degree, could compensate for less 7 We refer to the page numbers added by Petitioner to the bottom-center of the page. formal education.” Id. (citing Ex. 1003 ¶ 10). Patent Owner states that, “[f]or purposes of this Preliminary Response, Patent Owner applies Petitioner’s level of skill for a person of ordinary skill in the art.” Prelim. Resp. 4. For purposes of this Decision, we adopt Petitioner’s undisputed proposed definition because it appears to be consistent with the cited prior art and the disclosure of the ’689 patent. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (explaining that specific findings regarding ordinary skill level are not required “where the prior art itself reflects an appropriate level and a need for testimony is not shown” (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163–64 (Fed. Cir. 1985))).” slip op. at 10
- Expert testimonyPetitioner expert discountedDecided for patent owner
“We are not persuaded, on this record, that Petitioner adequately establishes that Khatibi discloses a CTE in the claimed range of 16 to 22 µm/(m·°C.). Petitioner’s argument that Khatibi’s reported values meet this claim limitation are based solely on Dr. Randall’s testimony that Khatibi’s measurement method would produce results that would not significantly differ from results determined using the claimed method. See Pet. 16–18 (citing Ex. 1003 ¶¶ 56–60). Dr. Randall’s testimony, however, is largely conclusory and unsupported by adequate explanation and/or objective evidence. For example, Dr. Randall does not provide adequate explanation or objective evidence to support his opinion that Khatibi’s use of a laser speckle based dilatometer instead of the claimed thermomechanical analyzer “is unlikely to significantly impact the CTE value” because “variations in equipment and a heating speed of 5° C/min would not significantly alter the results.” Ex. 1003 ¶ 58. In particular, Dr. Randall neither explains what constitutes a “significant” impact on CTE, nor provides objective evidence to support his contention that equipment variations and heating differences would not “significantly alter” the resulting measurements. And although Dr. Randall opines that “the heating rate (5°C per minute) is typical for certain devices” such as a thermomechanical analyzer or dilatometer, and “[t]ypically, these devices use temperature ramp rates between 2°C and 20°C per minutes, so the ‘5° C./min’ recited in [1d] is common and should not drastically affect the measurement results,” Dr. Randall fails to point us to any evidence showing that these temperatures are “typical” or that the claimed heating rate is “common.” Id. ¶ 59 (emphases added). to little weight. See 37 C.F.R. § 42.65(a) (“Expert testimony that does not disclose the underlying facts or data on which the opinion is based is entitled to little or no weight.”); Xerox Corp. v. Bytemark, Inc., IPR2022-00624, Paper 12 at 5 (PTAB Feb. 10, 2023) (finding that “the Board was correct in giving little weight to Petitioner’s expert because the expert declaration merely offered conclusory assertions without underlying factual support”); Upjohn Co. v. Mova Pharm. Corp., 225 F.3d 1306, 1311 (Fed. Cir. 2000) (“Lack of factual support for expert opinion to factual determinations, however, may render the testimony of little probative value in a validity determination.” (quoting Ashland Oil, Inc. v. Delta Resins and Refractories, Inc., 776 F.2d 281, 294 (Fed. Cir. 1985))); see also In re Ethicon, Inc., 844 F.3d 1344, 1348, 1352 (Fed. Cir. 2017) (concluding that the Board properly gave “little weight” to conclusory expert testimony of objective indicia). Because Petitioner offers Dr. Randall’s testimony to supply a limitation missing from the prior art, namely, the CTE measurement method, and we give Dr. Randall’s unsupported and conclusory testimony little weight, we are not persuaded that Petitioner establishes a reasonable likelihood of showing that Khatibi discloses limitation [1d].” slip op. at 17
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable
“second surfaces of the electrolytic copper foil ranges from 3 to 92.” Ex. 1001, 13:62–63. Petitioner contends that “Kim teaches that the electrolytic copper foil (e.g., untreated or treated copper foil) having Rz less than 2 µm is advantageous toward battery efficiency and performance,” and, similarly, Griesi describes the use of untreated electrolytic copper foil with an Rz value less than 2 µm in printed circuit boards that are compatible with secondary batteries. Pet. 58–59 (citing Ex. 1012, claim 2, ¶¶ 13, 25, 27; Ex. 1003 ¶ 157). In particular, Petitioner notes that Griesi’s Figure 3.16 describes an “Rz value of 1.2 µm.” Id. at 59 (citing Ex. 1015, 53–54; Ex. 1003 ¶ 158). Petitioner asserts that “Dr. Randall explains that a POSITA would have also recognized another surface roughness-related parameter, Rpc, in Griesi as a potentially useful parameter that can be optimized to further enhance uniformity or generally improve Kim’s copper foil surface, for example, to prevent wrinkles or achieve other advantageous effects.” Id. (citing Ex. 1003 ¶ 159). Although Dr. Randall demonstrates that Griesi’s Pc (or Rpc) value is 19.2 over a 4 mm sampling length (Ex. 1003 ¶ 155), Petitioner does not contend that Griesi addresses this value, or indicates any benefit that might be derived from its use. Instead, Griesi’s Pc value appears to be an incidental finding, which is not discussed or analyzed in the reference. See incidental, unexamined finding would lead a POSITA to import Griesi’s Pc value into Kim’s copper foil, absent a hindsight desire to reconstruct the claimed invention. As such, Petitioner’s arguments with respect to Kim and Griesi are not persuasive. See Cheese Sys. Inc. v. Tetra Pak Cheese and Powder Sys., Inc., 725 F.3d 1341, 1352 (Fed. Cir. 2013) (“Obviousness cannot be based on the hindsight combination of components selectively culled from the prior art to fit the parameters of the patented invention.” (internal quotations marks omitted)). Thus, we are not persuaded, on this record, that the combined disclosures of Kim and Griesi teach all of the elements of limitation [1g].” slip op. at 23
§ 103 obviousnesscites PhillipsPatents in suitUS 10,811,689 - Solus Advanced Materials Co, Ltd. v. SK Nexilis Co., Ltd.Institution deniedPTAB · Apr 22, 2025 · IPR2024-01460 · APJ Jon B Tornquist · IPR · Institution
The Board denied institution of review of claims 1–11 because the Fintiv factors, including the early trial date and close merits case, favored discretionary denial.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied fintivInstitution denied
“whether to institute an inter partes review. Applying the standard set forth in 35 U.S.C. § 314(a), we may not institute an inter partes review unless the information presented in the petition “shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” Institution of inter partes review, however, is discretionary. See Harmonic Inc. v. Avid Tech., Inc., 815 F.3d 1356, 1367 (Fed. Cir. 2016) (“[T]he PTO is permitted, but never compelled, to institute an IPR proceeding.”). For the reasons stated below, we exercise our discretion not to institute an inter partes review. A. Real Parties-in-Interest” slip op. at 2
- PTAB / AIA Trials › Discretionary denial › Fintiv (parallel litigation)Institution denied fintivDenied
“Board’s projected statutory deadline to issue a final written decision. Fintiv, Paper 11 at 9. “If the court’s trial date is at or around the same time as the projected statutory deadline . . . the decision whether to institute will likely implicate other factors.” Id. Conversely, “[i]f the court’s trial date is earlier than the projected statutory deadline,” this has generally weighed “in favor of exercising authority to deny institution.” Id.” slip op. at 15
- PTAB / AIA Trials › Discretionary denial › §325(d) same art / argumentsNot reached
“Petition under 35 U.S.C. § 325(d) because the same or substantially the same art and arguments were before the Examiner during prosecution and Petitioner’s has not demonstrated that the Examiner erred in a material manner when allowing the claims. Pet. 17–18. Given our discretionary denial of the Petition in view of the Fintiv factors, we do not address Petitioner’s further arguments with respect to § 325(d).” slip op. at 32
- Skill levelSkill level petitioner adoptedDecided for petitioner
“Patent Owner applies Petitioner’s recited level of ordinary skill in the art for purposes of its Preliminary Response. Prelim. Resp. 4. Upon review of the parties’ arguments and the prior art of record, we adopt Petitioner’s unopposed definition of the ordinarily skilled artisan for purposes of this decision as it appears consistent with the disclosures of the ’090 patent and the prior art of record. C. Claim Construction” slip op. at 9
§ 103 obviousnessDiscretionary denialcites Phillips · KSR · GrahamPatents in suitUS 10,480,090 - Innoscience (Zhuhai) Technology Company, Ltd. / Innoscience America, Inc. v. Efficient Power Conversion CorporationNo claims unpatentablePTAB · Mar 25, 2025 · IPR2023-01382 · APJ Kimberly Mcgraw · IPR · Final written decision
Claims 1–3 were not shown unpatentable under any of five § 103 grounds because Petitioner failed to establish sufficient motivation to modify or combine the prior art.
RulingsFinal written decision- BurdenNot shown unpatentable
“A petition must identify “with particularity . . . the evidence that supports the grounds for the challenge to each claim.” 35 U.S.C. § 312(a)(3) Here, Petitioner merely provides general assertions about multiple references, without clearly identifying how, or why a POSITA would have been motivated, to modify the processes disclosed in those references to arrive at the claimed invention. Thus, the Petition does not state with particularity that Saxler’s particular technique for etching is to be used instead of Beach’s etching step when substituting Beach’s self-aligned process for Saxler’s two mask process. Nor does the Petitioner provide a sufficient reason, absent hindsight, why a POSITA would have been motivated to combine the references to result in a process that forms Saxler’s Modified Figure 1A. Thus, for these additional reasons, Petitioner has not shown by a preponderance of the evidence that claim 1 would have been obvious over Saxler, Beach, and Shenoy.” slip op. at 34
- Skill levelSkill level petitioner adoptedDecided for petitioner
“Both parties agree that the differences between the definitions do not impact the analysis. Resp. 11; Reply 2. In light of the record before us, and for purposes of this Decision, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’347 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand and implement the teachings of the ’347 patent and the prior art. We also note that our Decision would be the same under either parties’ definition.” slip op. at 13
- Expert testimonyOther
“Petitioner’s expert, Dr. Shealy states that he understands paragraph 52 to mean that it is “fair game to pull the recess out of any of those figures [Figures 1A through 6].” Ex. 2004, 39:12–21. Dr. Shealy, however, also clarifies that “[a]s I said before, I think you could take all the embodiments and bring in which ones you want, depending on what you’re trying to accomplish.” Ex. 2004, 40:24–41:1. During the hearing, Petitioner admitted that Dr. Shealy’s “statement to modify the reference depending on what you're trying to accomplish” means that “a POSITA may modify with reason to do so. A POSITA would have removed Saxler’s recess to obtain the benefits of enhancement-mode.” Tr. 19:19–25. Again, the Petition does not provide a reason why a POSITA would have removed Saxler’s gate recess.” slip op. at 28
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable
“remove the recess in Saxler Figure 1A to arrive at the allegedly enhancement mode transistor of Modified Figure 1A. Contrary to Petitioner’s assertions in its Reply and at the hearing, the Petition makes no argument that a POSITA would have removed the recess from Saxler Figure 1A to realize the benefits of an enhancement mode transistor. See Reply 4–5; Pet. 24–68. Rather, the Petition merely asserts that a POSITA would have understood that the gate recess of Figure 1A is optional without providing any persuasive reason why a POSITA would have removed the gate recess but retained the sloped sidewalls of Figure 1A. Pet. 25, 40, 45. For example, Petitioner asserts that Saxler’s gate contact may be “recessed or non-recessed” and that when the gate recess shown in Figure 1A is not utilized, Saxler would have the structure of Saxler Modified Figure 1A. Pet. 25 (citing Ex. 1003 ¶ 81; Ex. 1007 ¶ 52, 66); see also Pet. 40, 45 (citing Ex. 1007 ¶ 52). Neither of these paragraphs provide sufficient motivation to a POSITA to remove the gate recess from Saxler Figure 1A. Saxler paragraph 52 states: Exemplary devices according to some embodiments of the present invention are schematically illustrated in FIGS. 1A through 6. Thus, while embodiments of the present invention are described herein with reference to a recessed gate structure or a non-recessed gate structure, other embodiments of the present invention may include or not include a gate recess. Accordingly, embodiments of the present invention should not be construed as limited to the particular exemplary embodiments described herein but may include any suitable structure having a cap layer and/or passivation layer as described herein. Ex. 1007 ¶ 52. Petitioner’s expert, Dr. Shealy states that he understands paragraph 52 to mean that it is “fair game to pull the recess out of any of those figures [Figures 1A through 6].” Ex. 2004, 39:12–21. Dr. Shealy, however, also clarifies that “[a]s I said before, I think you could take all the embodiments and bring in which ones you want, depending on what you’re trying to accomplish.” Ex. 2004, 40:24–41:1. During the hearing, Petitioner admitted that Dr. Shealy’s “statement to modify the reference depending on what you're trying to accomplish” means that “a POSITA may modify with reason to do so. A POSITA would have removed Saxler’s recess to obtain the benefits of enhancement-mode.” Tr. 19:19–25. Again, the Petition does not provide a reason why a POSITA would have removed Saxler’s gate recess.” slip op. at 28
Patent outcomesUS 9,748,347 not shown unpatentable§ 103 obviousnesscites Phillips · KSRPatents in suitUS 9,748,347
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.