- Samsung Electronics Co., Ltd. / Samsung Electronics America, Inc. v. Ouraring, Inc.No claims unpatentablePTAB · Jul 10, 2026 · IPR2025-00147 · APJ Linda E Horner · IPR · Final written decision
The Board found claims 1–6 and 8–20 not shown unpatentable under three obviousness grounds, principally because the proposed combinations did not establish a feasible curved battery or transparent potting encapsulating the components.
RulingsFinal written decision- Skill levelSkill level board ownOther
“at least a four-year degree in electrical engineering, mechanical engineering, biomedical engineering, optical engineering, or related field of study, or equivalent experience, and at least two years’ experience in academia or industry studying or developing physiological monitoring devices such as non-invasive biosensors. Pet. 8 (citing Ex. 1002 ¶ 29). Petitioner also contends that a person of ordinary skill would have been “familiar with, e.g., sensor system design, including inertial and other motion sensor system design, and signal processing” and that “[a] higher level of education or skill might make up for less experience, and vice versa.” Id. Patent Owner agrees with Petitioner’s proposed definition of a person of ordinary skill in the art. Resp. 25. We adopt this uncontested definition of the level of ordinary skill in the art. This definition is supported by the record and consistent with the disclosure in the ’124 patent and the references cited in the Petition.” slip op. at 10
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“We need not reach the issue of whether the preamble is limiting for purposes of determining patentability of the challenged claims. Even were we to agree with Patent Owner that the preamble is limiting and the claims are limited to a finger-worn ring wearable computer device, Petitioner has relied on Schröder in each ground to disclose a “wearable computing device configured to be worn around a finger of a wearer.” Pet. 22 (Ground 1), 45 (Ground 2, relying on Yuen for adding the functionality of light sources with a photodetector, temperature sensors, and varying the sampling frequency of sensor data acquisition), 56 (Ground 3). We agree with Petitioner that Schröder discloses such a device. Thus, no explicit claim construction is necessary for this decision.” slip op. at 11
- Obviousness (§103) › Motivation to combine / reasonable expectation of successReasonable expectation not foundNot shown unpatentableNot shown unpatentable
“We are not persuaded by Petitioner’s arguments and find that Patent Owner has the better position for several reasons. First, the record supports Patent Owner’s argument that Mestas’s batteries are much too large to fit within a ring form factor, and “would have to be reduced in size on the 6 There is no Exhibit 2022 in the record of this case. magnitude of 5-10x from its current size to fit in a ring of Schröder.” Resp. 38 (citing Dr. Anthony’s cross-examination testimony at Ex. 2021, 313:12). Second, Petitioner relies on evidence in the Reply that Petitioner failed to specifically identify in the Petition. Compare Reply 3–5 (citing Ex. 1369 ¶¶ 7–14; Ex. 1079 ¶¶ 47, 71; Ex. 2022, 138:7–143:1; Ex. 1002 ¶¶ 96, 337; Ex. 2021, 12–13, 307:7–17; Ex. 2020, 212:6–214:13; Ex. 1081, 130:18–131:14; Ex. 1010 ¶ 168), 9 (referring back to Section § II.B.2) with Pet. 25–26 (citing Ex. 1002 ¶¶ 193–99; Ex. 1010 ¶¶ 157, 163, 168, 201, Fig. 6). More specifically, while the portion of Dr. Anthony’s Declaration cited in the Petition (see Pet. 25–26 (citing Ex. 1002 ¶¶ 193–99)) mentions the Technology Background Section V of his Declaration (Ex. 1002 ¶¶ 42–147), neither Petitioner nor Dr. Anthony sufficiently explains what evidence supports his opinion that it was feasible to incorporate batteries or battery-like devices into finger-rings, or how a person of ordinary skill in the art would have miniaturized a curved battery for incorporation into Schröder’s ring. Ex. 1002 ¶ 196 (describing that rechargeable batteries powering wearable electronic devices were “well-known by 2013” and “had also undergone significant advances in terms of miniaturization and energy density [that] made it feasible to incorporate batteries or battery-like devices such as supercapacitors into smaller form factors, such as finger rings, without sacrificing functionality” such as “lithium-polymer (Li-Po) batteries and solid-state batteries.”). Moreover, some of Petitioner’s citations in the Reply appear to be incorrect as there is no Exhibit 2022 of record in this case, as noted above. These issues undermine the strength of Petitioner’s showing by making it difficult to follow its reasoning, much less identify where in the record that reasoning finds support. See DeSilva v. DiLeonardi, 181 F.3d 865, 866–67 (7th Cir. 1999) (“A brief must make all arguments accessible to the judges, rather than ask them to play archaeologist with the record.”); United States v. Dunkel, 927 F.2d 955, 956 (7th Cir. 1991) (“Judges are not like pigs, hunting for truffles buried in briefs.”). Third, even considering Petitioner’s new Reply arguments and” slip op. at 27
- Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner
“We credit Dr. Mercier’s testimony over Dr. Anthony’s and agree that Dr. Anthony’s testimony fails to account for the constraints of a substantially smaller form factor in Schröder’s finger-ring as compared to Mestas’s wrist device. Ex. 2018 ¶ 140. Although large curved batteries suitable for use in a wrist band or other larger wearable device, such as shown in Mestas, were known at the time of the ’124 patent, we also have evidence that prior art “finger ring wearables up to the ’124 patent had used ‘coin’ type batteries.” Resp. 40 (citing Ex. 2018 ¶ 140). We credit Dr. Mercier’s testimony that a person having ordinary skill in the art would have looked to a coin type battery for the necessary power requirements of Schröder’s device. Ex. 2018 ¶ 141. Indeed, this testimony is consistent with the other art of record that consistently shows the use of flat batteries in finger-ring devices, often stacked above and protruding from the general ring shape of the device. See, e.g., Ex. 1005 (Niwa), Figs. 22, 28; Ex. 2025 (Asada ’701 patent), Fig. 4; Ex. 1035 (Rhee), Figs. 7-1, 8-1, 8-2; Ex. 1037 (Asada article), Fig. 9; Ex. 1034 (Asada ’199 patent), Fig. 2; Ex. 1028 (Kimura patent), Fig. 24; Ex. 2018 ¶¶ 74–84. In fact, Oura’s first-generation ring design, released in 2015, used a Superbowl ring type design, with the battery and other components mounted on top of the ring. Ex. 2034; Ex. 2018 ¶ 85. We also agree with Dr. Mercier that Dr. Anthony’s testimony lacks evidence or a technical analysis of the power requirements for the various sensors he suggests including in a wearable device and the capacity of the proposed GMBPow battery. See, e.g., Ex. 1002 ¶¶ 94, 210, 214–17; Ex. 2018 ¶ 97. Moreover, Dr. Anthony does not address the issues with the batteries that are identified in the references he discusses. For example, Dr. Anthony does not address Lee’s disclosure that “direct coating of electrode slurry onto plain paper led to the occasional internal-shorting of the device due to the leakage of the electrode material through a large-sized hole in the paper.” Ex. 1019, 2415. In contrast, Dr. Mercier discusses the pitfalls the skilled artisan faced in developing finger-ring devices. See, e.g., Ex. 2018 ¶¶ 77–79 (discussing the issues Rhee’s and Asada’s large rings), 83 (identifying power requirements as a design constraint). For example, Dr. Mercier explains that “flexible or curved batteries include flexible packaging materials such as aluminum laminated films that house the electrodes and electrolyte” such that “once the battery packaging is added to a battery such as GMBPow and then placed within a housing (e.g., external housing shell and internal potting), the resulting device would have dimensions that are not suitable for a finger-worn ring.” Id. ¶ 96 (citing Ex. 2026).” slip op. at 34
Patent outcomesUS 11,188,124 not shown unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 11,188,124 - Resmed Corp. v. Cleveland Medical Devices, Inc.All claims unpatentablePTAB · Jun 29, 2026 · IPR2025-00246 · APJ Cynthia M Hardman · IPR · Final written decision
Claims 15–29 are unpatentable as obvious over the asserted combinations; the contingent motion to amend claims 30–41 is denied for lack of written-description support.
RulingsFinal written decision- PTAB / AIA Trials › Real party in interest / privityRpi dispute resolved for petitionerDecided for petitioner
“Patent Owner filed an authorized Motion to Terminate, alleging that Petitioner failed to name its corporate parent, ResMed Inc., as a real party in interest. Paper 39. Petitioner filed an opposition. Paper 42. Patent Owner filed a reply. Paper 43. We denied the Motion to Terminate. Paper 51.” slip op. at 3
- Skill levelSkill level board ownOther
“understanding of a person of ordinary skill in the art at the time the invention was made.10 See Graham, 383 U.S. at 17–18. The parties agree that a person of ordinary skill in the art (sometimes referred to herein as “POSITA”) would have had: at least a bachelor’s degree in mechanical engineering, electrical engineering, computer science, biomedical engineering, or a similar technical field, with at least two years of relevant product design experience working with diagnostic sensor systems and network data systems, such as networked PAP machines. Additional experience could substitute for less education, and additional education could likewise substitute for less experience. Pet. 3–4 (citing Ex. 1003 (Kirkness Decl.) ¶ 44); PO Resp. 4. 9 Patent Owner does not assert any objective indicia of nonobviousness. See generally PO Resp. 10 For purposes of this Decision, we apply a priority date of November 4, 2005. See supra n.4. Because the proposed level of ordinary skill in the art is consistent with the cited prior art and is undisputed on this record, we adopt it for purposes of this Decision. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (indicating that the prior art itself may reflect an appropriate skill level).” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Patent Owner does not persuade us to construe the term as “a value [or calculated value] that indicates how dire a patient’s symptoms are.” Patent Owner points to nothing in the intrinsic record that purportedly supports this construction, and we agree with Petitioner that “the patent specification’s disclosures regarding determining a level of symptom severity are broad, establishing that it can generally be derived from any sensor data and/or breathing events.” Pet. Reply 3–4; see also Ex. 1001, 3:44–46 (“Signals from the[] sensors are then analyzed to determine the level of severity of the symptoms of the subject’s sleep disorder.”). Patent Owner relies only on expert declarations to support its construction. But as indicated by the Federal Circuit, extrinsic evidence is “less significant than the intrinsic record in determining ‘the legally operative meaning of claim language.’” Phillips v. AWH Corp., 415 F.3d 1303, 1317 (Fed. Cir. 2005). This is especially applicable here, where neither Dr. D’Ambrosio’s nor Dr. Schwartz’s declaration was prepared for this proceeding, and neither declarant was subject to cross examination on their opinions. Moreover, neither of the declarants was opining on claim construction; rather, they were addressing indefiniteness and/or written description issues. See Ex. 1058 at 7 (heading addressing definiteness); Ex. 2026 at 18 (heading addressing written description). Further, Dr. Schwartz appears to have been making an argument about certain patent claims (not the challenged ’333 patent) based on Patent Owner’s own statements made during prosecution of a separate patent application. See Ex. 2026 ¶ 47 (“[T]he similar term used in the ’284 patent claims (‘data of severity of sleep disorder symptoms’) does not find written description support in the specification by a disclosure of the same statistics disclosed in Wright, because CleveMed argued those statistics are not related to severity of sleep disorder symptoms.” (emphasis added)). Patent Owner has not persuaded us that Dr. Schwartz’s testimony has direct applicability to the claim term at issue here. Dr. Borkholder’s testimony is likewise unpersuasive. Aside from citing Dr. D’Ambrosio’s and Dr. Schwartz’s declarations, Dr. Borkholder cites Exhibits 2027 and 2016. These exhibits discuss indices such as AHI and RDI that are used to assess the severity of a patient’s symptoms, but Patent Owner has not adequately explained how they bear on construction of the claim term at issue here, which is not addressed in these exhibits. Ex. 2022 ¶¶ 32–33. Accordingly, we accord Dr. Borkholder’s claim construction opinions little weight, because they are unsupported by reference to objective, corroborating evidence of record. See, e.g., Ashland Oil, Inc. v. Delta Resins & Refractories, Inc., 776 F.2d 281, 294 (Fed. Cir. 1985) (“Lack of factual support for expert opinion going to factual determinations . . . may render the testimony of little probative value in a validity determination.”); Xerox Corp. v. Bytemark, IPR2022-00624, Paper 9, 15 (PTAB 2023) (precedential) (explaining that declaration testimony that “is conclusory and unsupported” and which “adds little to the conclusory assertion for which it is offered to support . . . is entitled to little weight”).” slip op. at 23
- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable
“We find that Petitioner has the better argument. Tidal volume refers to “the volume of air that is inspired or expired during a respiratory cycle.” Ex. 2028, 13–14; PO Resp. 10. “[H]ypopnea events are defined as a reduction of ≥50 % or 74 % in tidal volume from baseline and apnea events as absence of tidal volume for at least 10s.” Ex. 2028, 13–14 (emphasis omitted). Toge teaches that a control unit analyzes collected data (e.g., the flow rate) and calculates tidal volume. Ex. 1044 (Toge) ¶¶ 34–38. The calculated tidal volume is “a quantified level of severity data based on the subject’s sleep apnea symptoms during the therapy” because it represents, e.g., the “level of airway obstruction the patient experiences during the sleep apnea treatment using the PAP device.” Pet. 15. As Dr. Chatterjee explains: Toge discloses that tidal volume Fp is a quantified level of data because Toge discloses that Fp is monitored with respect to threshold values (id., [0051]) and because Fp is a function of Ft, Fa, and Fb, which are quantitative values. Toge discloses that tidal volume Fp is severity data because Toge discloses that tidal volume is indicative of whether the patient’s breathing warrants “emergency measures” (id., [0039]) and whether to “send an alert” in “an emergency where the patient’s breathing has drastically weakened” (id., [0055]). . . . . Because Toge discloses determining tidal volume (determine a quantified level of severity data) based on Ft, Fa, and Fb (id., [0035]), which corresponds to the subject’s condition (subject’s sleep apnea symptoms) while using the device (during the therapy) (id., [0036], [0037]), Toge discloses determin[ing] a quantified level of severity data based on the subject’s sleep apnea symptoms during the therapy. Ex. 1005 (Chatterjee Decl.) ¶¶ 122–125. Patent Owner’s attempt to dismiss tidal volume as a mere “breathing metric” is unavailing. First, Petitioner correctly “notes that in the paragraph PO cites to in Dr. Schwartz’s declaration, he indicates that breathing metrics are a level of severity data.” Pet. Reply 8 (citing Ex. 2026 ¶ 46 (“standard sleep disordered breathing metrics” [ ] were well validated indicators of the type and severity of sleep disordered breathing”)). Second, Dr. Kirkness explains that tidal volume represents the level of airway obstruction, e.g., apnea “is the most severe form of reduction in airflow [and] the absence of airflow results in quantified tidal volume of zero milliliters per breath.” Ex. 1003 (Kirkness Decl.) ¶¶ 157, 159; see also PO Resp. 10–11 (Patent Owner recognizing that an apnea is defined as absence of tidal volume for at least 10 seconds). The calculated tidal volume thus indicates severity because it is used to adjust the PAP system, e.g., in the case of decreasing tidal volume, a medical professional can change the airflow settings “to counter/treat the more severe level of airway obstruction observed from the decreasing tidal volume.” Ex. 1003 (Kirkness Decl.) ¶ 158; Pet. 15–16; Ex. 1044 (Toge) ¶ 39.” slip op. at 26
Patent outcomesUS 11,857,333 unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 11,857,333 - Resmed Corp. v. Cleveland Medical Devices, Inc.No claims unpatentablePTAB · Jun 5, 2026 · IPR2025-00160 · APJ Sheridan K Snedden · IPR · Final written decision
Claims 1–5, 7, 8, 10–13, 15–18, and 20–31 were not shown unpatentable because the proposed Toge-Kumar combination did not establish the claimed remote internet site hosted on a server.
RulingsFinal written decision- PTAB / AIA Trials › Real party in interest / privityRpi dispute resolved for petitionerDecided for petitioner
“Patent Owner filed a Response. Paper 23 (“PO Resp.”). Petitioner filed a Reply. Paper 27 (“Reply”). Patent Owner filed a Sur-reply. Paper 35 (“Sur-reply”). Additionally, during trial, Patent Owner filed an authorized Motion to Terminate, alleging that Petitioner failed to name a real party in interest (namely, Petitioner’s corporate parent, Resmed Inc.). Paper 37. Petitioner filed an opposition. Paper 38. Patent Owner filed a reply. Paper 39. We denied the Motion to Terminate. Paper 44.” slip op. at 2
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“We determine that no express construction of any claim term is necessary to resolve the dispute between the parties. Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))). To the extent further discussion of the meaning of any claim term is necessary to our decision, we provide that discussion below in our analysis of the asserted grounds of unpatentability. C. Level of Ordinary Skill in the Art” slip op. at 11
- Skill levelSkill level petitioner adoptedDecided for petitioner
“We adopt Petitioner’s proposed level of ordinary skill in the art because it appears to be consistent with the cited prior art and is undisputed on this record. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (indicating that the prior art itself may reflect an appropriate skill level). D. Summary of the Asserted Prior Art” slip op. at 12
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable
“summarized above, we determine that a person of ordinary skill in the art would not have implemented Toge’s physician-side computer as a web server using a “localhost” architecture as proposed by Petitioner because such a configuration cannot communicate with external devices over the public internet, a deficiency that directly contradicts Petitioner’s stated motivations for the combination of permitting broad data access. Petitioner’s expert, Dr. Chatterjee, expressly acknowledged in his Reply Declaration that when a client and server reside on the same machine, the communications between them do not traverse the internet. Ex. 1069 ¶ 8. Specifically, Dr. Chatterjee cited the Microsoft Computer Dictionary’s definition of “localhost” as “[t]he name that is used to represent the same computer on which a TCP/IP message originates,” noting that “[a]n IP packet sent to localhost has the IP address 127.0.0.1 and does not actually go out to the Internet.” Id. (citing Ex. 1070, 316). Accordingly, Petitioner’s proposed configuration of placing both the client and web server on Toge’s physician-side computer would create a closed loop of communication that does not reach the broader network. Id. As noted by Patent Owner, “[i]f ‘the physician-side computer and the web server are on one machine,’ the local web server would not communicate with other devices via the Internet.” Sur-Reply, 3–4 (comparing Ex. 1069 ¶ 19 with id. at ¶ 8). Thus, the consequence of Petitioner’s proposed Toge-Kumar configuration is that other devices in the system, such as the PAP device that generates the treatment data and any remote client devices that might need to access that data, would be unable to send data to or retrieve data from the localhost web server. Patent Owner persuasively argues, supported by evidence of record, that under Petitioner’s proposed configuration, “the PAP device could not send data thereto nor could other clients receive data therefrom, as only the local client browser can exchange data.” Id. (citing Ex. 1069 ¶ 8); see Ex. 2003, 4 (one-tier architecture “is not suitable for a web application” because “it can only access data available in a single computer or server” and therefore “is not suitable for a web application.”); Ex. 2022, 3 (Unlike more advanced multi-tier systems, a one-tier architecture “cannot transmit information from one client machine to another.”); Ex. 2020, 4 (While “the client process and server process can be on the same computer,” this architecture “is rarely used today” precisely because it cannot “take advantage of the distributed computing environment.”).” slip op. at 29
Patent outcomesUS 11,786,680 not shown unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 11,786,680 - Resmed Corp. v. Cleveland Medical Devices, Inc.No claims unpatentablePTAB · Jun 4, 2026 · IPR2025-00158 · APJ Sheridan K Snedden · IPR · Final written decision
Claims 1–20 were not shown unpatentable because Orbach did not disclose a single computer or processor performing all claimed remote analysis, output, and display functions.
RulingsFinal written decision- BurdenNot shown unpatentable
“After considering all of the arguments and evidence presented on the full trial record, we determine that Petitioner has not demonstrated by a preponderance of the evidence that claims 1–6, 8–17, 19, and 20 are unpatentable as obvious over the combination of Ciulla and Orbach. We find that the deficiencies in Petitioner’s arguments regarding claim limitations [1.d], [1.f], and [1.g] are dispositive and we address the parties’ arguments concerning those limitations below.” slip op. at 24
- Skill levelSkill level petitioner adoptedOther
“Pet. 8. Patent Owner agrees to apply Petitioner’s proposed definition of POSITA. PO Resp. 4. We adopt Petitioner’s proposed definition of a POSITA because the proposed level of ordinary skill in the art appears to be consistent with the cited prior art and is undisputed on this record. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (indicating that the prior art itself may reflect an appropriate skill level).” slip op. at 11
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“the Board need not construe any terms. Pet. 9. Patent Owner agrees. PO Resp. 4. We determine that no express construction of any claim term is necessary to resolve the dispute between the parties. Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (“[W]e need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))). Nevertheless, in our analysis of the asserted grounds of unpatentability below, we discuss the scope of certain claim terms, e.g., “the computer” and “the processor.” C. Level of Ordinary Skill in the Art” slip op. at 11
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable
“Accordingly, to show obviousness, Petitioner must show in Orbach that either (a) remote server 140’s output to viewing station 150 constitutes “display” within the meaning of the claim, or (b) viewing station 150 receives data “over cell towers” notwithstanding the intervening server. We determine that Petitioner has failed to do so on this record. Our analysis follows.” slip op. at 33
Patent outcomesUS 11,690,512 not shown unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 11,690,512 - Resmed Corp. v. Cleveland Medical Devices, Inc.No claims unpatentablePTAB · May 18, 2026 · IPR2025-00159 · APJ Cynthia M Hardman · IPR · Final written decision
Claims 1, 2, 4, 5, 7–9, 11–14, and 16 were not shown unpatentable under either § 103 ground because Petitioner did not establish the proposed remote internet site modification.
RulingsFinal written decision- PTAB / AIA Trials › Real party in interest / privityRpi dispute resolved for patent ownerDecided for patent owner
“Patent Owner filed an authorized Motion to Terminate, alleging that Petitioner failed to name a real party in interest (namely, Petitioner’s corporate parent, Resmed Inc.). Paper 37. Petitioner filed an opposition. Paper 38. Patent Owner filed a reply. Paper 39. We denied the Motion to Terminate. Paper 44.” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“understanding of a person of ordinary skill in the art at the time the invention was made.8 See Graham, 383 U.S. at 17–18. The parties agree that a person of ordinary skill in the art (sometimes referred to herein as a POSITA) would have had: at least a bachelor’s degree in mechanical engineering, electrical engineering, computer science, biomedical engineering, or a similar technical field, with at least two years of relevant product design experience working with diagnostic sensor systems and network data systems, such as networked PAP machines. Additional experience could substitute for less education, and additional education could likewise substitute for less experience. Pet. 12–13 (citing Ex. 1003 (Kirkness Decl.) ¶¶ 44–46); PO Resp. 7–8. Because the proposed level of ordinary skill in the art is consistent with the cited prior art and is undisputed on this record, we adopt it for purposes of this Decision. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (indicating that the prior art itself may reflect an appropriate skill level).” slip op. at 11
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“We find it unnecessary to construe any claim term to resolve the issues in this case. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (noting that “we need only construe terms ‘that are in controversy, and only to the extent necessary to resolve the controversy’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 12
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable
“its burden of explaining why a person of ordinary skill in the art would have implemented a remote internet site in Toge’s system in the specific fashion Petitioner asserts (i.e., using the physician-side computer as a web server). As Patent Owner aptly states, the operative question is not merely whether a person of ordinary skill in the art would have modified Toge’s system to include a remote internet site, but whether the artisan would have modified Toge’s system to include a remote internet site “on a physician’s client computer” in accordance with the specific implementation argued by Petitioner. Sur-reply 2. On this critical question, Petitioner’s arguments are thin. Petitioner’s declarant Dr. Kirkness states that a person of ordinary skill in the art “would have understood that one common way to access data transmitted over the internet, like the data from Toge’s wireless PAP device, is via a remote internet site.” Ex. 1003 ¶ 214. This assertion is reasonable. Indeed, prior art of record, such as Kumar, illustrates use of a central server that hosts a browser-based engine that can be accessed through web pages. See, e.g., Ex. 1008 (Kumar) Fig. 1A, ¶¶ 67, 72, 79, Pet. 10. Petitioner, however, elected to argue a specific implementation, namely that the skilled artisan would have modified Toge’s physician-side computer to operate as a web server. See, e.g., Pet. 15; Ex. 1005 (Chatterjee Decl.) ¶ 146; Reply 4. We find that this implementation is unsupported on this record. Petitioner has not pointed us to any disclosure in Toge, Burton, or Kumar (or any other prior art reference of record) that teaches or suggests “that a doctor’s computer should act a web server hosting sensitive patient data.” PO Resp. 9 (emphasis added). And critically, the Petition is silent as to why a person of ordinary skill in the art would have selected this implementation in particular. See, e.g., Pet. 49.” slip op. at 25
Patent outcomesUS 11,375,921 not shown unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 11,375,921 - Samsung Electronics Co., Ltd. / Samsung Electronics America, Inc. v. Ouraring, Inc.No claims unpatentablePTAB · Jan 30, 2026 · IPR2024-01078 · APJ Neil T Powell · IPR · Final written decision
Claims 1–6, 11–15, and 38–43 were not shown unpatentable because Petitioner failed to establish obviousness over the asserted combinations, including the feasibility and motivation to use curved batteries in a ring.
RulingsFinal written decision- Skill levelSkill level board ownDecided for petitioner
“Patent Owner agrees with Petitioner’s proposed definition of a person of ordinary skill in the art. PO Resp. 22; see also Ex. 2018 ¶ 27. We adopt this uncontested definition of the level of ordinary skill in the art. This definition is supported by the record and consistent with the disclosure in the ’953 patent and the references cited in the Petition.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Petitioner expresses that it “does not believe that any term requires express construction.” Pet. 8. “Patent Owner agrees with Petitioner that no terms need to be construed.” PO Resp. 22. We agree with the parties that resolution of their dispute does not require us to construe any claim terms. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (holding that only claim terms in controversy controversy) (citing Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 9
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundReasonable expectation not foundNot shown unpatentable
“be improper hindsight in Petitioner’s position. Petitioner and Dr. Anthony assume that a POSITA would position the battery between Schröder’s ring halves and implement Mestas’s curved battery because it “allows a larger battery to conform to a ring’s circular shape without stressing the battery or ring housing.” Pet. 60, 64–65; Ex. 1002 ¶¶ 337, 351–354. That position, however, ignores alternative designs that are at least equally supported by Schröder’s disclosure (see Ex. 1007, Fig. 3), but would not result in a ring configured as recited in the challenged claims. Petitioner attempts to downplay this concern by characterizing the modification of Schröder’s ring to include Mestas’s curved battery as an obvious “matter of choice” in design. See Reply 10–11 (citing Ex. 1079 ¶¶ 71–77). We disagree. As explained above, the record supports Patent Owner’s argument that Mestas’s batteries are much too large to fit within a ring form factor because they are “5 to 10 times” the size that would be required for a finger ring. PO Resp. 27 (quoting Ex. 2021, 313:12). Petitioner argues that it “does not propose bodily incorporating Mestas’s battery into Schröder’s ring,” which on the surface is correct. See Reply 10. But this does not help Petitioner meet its burden because its actual obviousness theory that “a POSITA would have found it trivial to implement Mestas’s teachings into a ring like Schröder’s ‘finger-ring’” is not persuasive. See Pet. 60 (citing Ex. 1002 ¶ 338). For the same reasons explained in Section II.D.1 above in our analysis of Ground 1, Dr. Mestas’s teaching of a curved battery (Ex. 1002 ¶ 338) in the much smaller form factor of Schröder’s ring is not credible. See Ex. 2021, 315:9–318:9 (acknowledging that it would have been beyond the level of ordinary skill to miniaturize Mestas’s battery, but that a POSITA could try to procure one); 321:5–10 (conceding that he did not try to ascertain whether such a battery was available in the relevant time frame). Instead, we credit Dr. Mercier’s testimony that Petitioner’s proposed modification would have presented intractable practical challenges. Ex. 2018 ¶¶ 228, 230–240 (describing various aspects of battery design that Dr. Anthony did not consider). As before, Dr. Mercier’s testimony is further supported by evidence showing a consistent pattern of flat battery use in prior art finger-ring devices. See, e.g., Ex. 1005 (Niwa), Figs. 22, 29; Ex. 2025 (Asada ’701 patent), Fig. 4; Ex. 1035 (Rhee), Figs. 7-1, 8-1, 8-2; Ex. 1037 (Asada article), Fig. 9; Ex. 1034 (Asada ’199 patent), Fig. 2; Ex. 1028 (Kimura), Fig. 24; Ex. 2018 ¶¶ 57–67. In sum, Petitioner’s showing for limitation 1[c] is deficient in multiple respects. First, Petitioner assumes that an ordinarily-skilled artisan would have been motivated to implement Mestas’s curved battery in the much smaller interior space occupied by Schröder’s inlay 12 without sufficiently considering the feasibility of that modification or alternative designs suggested by Schröder. Second, even if we accept Petitioner’s purported rationale for the combination (which we do not because we find it that it is predicated on improper hindsight), Petitioner has not shown that an ordinarily-skilled artisan would have had a reasonable expectation of successfully implementing the proposed modification.” slip op. at 46
- Obviousness (§103) › Objective indicia / secondary considerations › NexusObjective indicia with nexusDecided for patent owner
“We find that the evidence presented by Patent Owner is sufficient to establish that the Oura Ring Gen. 3 Horizon and Gen. 4 products are commercial embodiments of claim 1 of the ’953 patent and that claim 1 is coextensive in that it encompasses the entire structural apparatus of these products. See PO Resp. 82–92; Ex. 2018 ¶¶ 322–346 (comparing these products to claim 1); Ex. 2029; Ex. 2030; Ex. 2118; Ex. 2119.9 Indeed, Petitioner does not challenge any aspect of Dr. Mercier’s limitation-by-limitation analysis showing that these products practice claim 1. But more than just practicing the claimed invention, Patent Owner’s evidence supports that claim 1 recites the overall structure that provides for the particular form factor of the Oura Ring Gen. 3 Horizon and Gen. 4 products, i.e., a fingerring “wedding band” design that allows for the electronic components to be entirely contained within the ring housing with a curved external surface having no protrusions or bulges. Ex. 2018 ¶¶ 359–360; see also id. ¶¶ 322–346 (pictures depicting wedding band design of the Oura Ring Gen. 3 Horizon and Gen. 4 products); Ex. 2019 ¶¶ 47–49 (“[Patent Owner’s] decision to highlight the ring form factor indicates this feature’s importance to the marketplace success of the Oura Ring.”). We disagree with Petitioner’s assertion that the Oura Ring Application and/or Oura Membership are essential, unclaimed features such that a presumption of nexus is not appropriate. The Oura Application functions in conjunction with the Oura Ring to form a “complete solution” 9 Patent Owner and Dr. Mercier only compare these products to claim 1. Patent Owner has not demonstrated a nexus to independent claim 38. ¶¶ 20–21. The Oura Application cannot receive or display any information absent the Oura Ring’s ability to collect the information from the user. Id. Even though the Oura Application may provide additional unclaimed functionality, such as displaying activity, sleep, and readiness scores based on the data collected by the Oura ring that allow “a user to take advantage of the ring’s offerings,” this functionality is secondary to the ring’s ability to collect that data, without which, the Oura Application would serve no purpose. See Ex. 2019 ¶ 21; Ex. 2024, 93:22–95:22. As the Federal Circuit has explained, “there is rarely a perfect correspondence between the claimed invention and the product.” Fox Factory, 944 F.3d at 1374. Here, we find that on the spectrum of “unclaimed features,” the Oura Ring Application is closer to the “insignificant features” end because, while it allows the user to access and interpret data tracked by their Oura Ring, it does not materially impact the functionality of the Oura Ring or its structure.10 See Teva 8 F.4th at 1361 (explaining that “like the coextensiveness requirement itself, the concept of unclaimed features is best viewed as part of a spectrum”).” slip op. at 27
Patent outcomesUS 10,281,953 not shown unpatentableClaim construction§ 103 obviousnesscites PhillipsPatents in suitUS 10,281,953 - 3d Diagnostix, Inc. v. Watson Guide IP, LLCAll claims unpatentablePTAB · Jan 27, 2026 · PGR2024-00040 · APJ James A Tartal · PGR · Final written decision
Claims 1–3, 5–7, 10, 12, 14, 16, and 17 are unpatentable under § 103, including over Llop ’126 and Sichuan, and over Llop ’126, Sichuan, and Scherer for claims 5, 6, and 12.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for patent owner
“B. Level of Ordinary Skill in the Art Petitioner contends that a person of ordinary skill in the art as of the earliest priority date of the ’209 patent “would at least have had a doctoral degree in dentistry and at least three to four years of experience working with guided dental surgery for installing dental implants and prostheses.” Pet. 13 (citing Ex. 1003 ¶ 49). Patent Owner agrees with Petitioner’s proposed definition of a person of ordinary skill in the art. Resp. 4. Based on our review of the record before us, we adopt Petitioner’s uncontested definition of a person of ordinary skill in the art, because it is supported by the evidence of record and consistent with the disclosure in the ’209 patent and in the asserted prior art.” slip op. at 11
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached
“1. “drill guide” and “fixation base” Petitioner contends that the claim terms “drill guide” and “fixation base” require construction “to resolve certain of the unpatentability grounds presented.” Pet. 13–14. In particular, Petitioner proposes that “drill guide” means “drill guide made from metal or metallic alloy without traditional plastic or acrylic,” and that “fixation base” means “fixation base made from metal, metallic alloy or other strong material without traditional plastic or acrylic.” Id. According to Petitioner, the Specification “teaches that the composition of the drill guide is ‘a metal or metallic alloy,’” and provides no other alternatives. Id. at 14 (citing Ex. 1001, 5:35–36). Petitioner similarly alleges that “fixation base” is described as “being fabricated from a metal, metal alloy, or other strong material,” and that “traditional plastic or acrylic” is excluded in light of disclosures in a provisional application. Id. at 21–24. According to Petitioner, its proposed constructions should be adopted “based on disclaimer of claim scope in the provisional application incorporated into the [’209] patent specification.” Id. at 14–24. Patent Owner contends that we need not address the constructions proposed by Petitioner because the issues addressed by Petitioner’s proposed constructions only concern allegations of unpatentability directed to claims 11 and 13, which Patent Owner disclaimed. Resp. 4–5; Disclaimer 1. In Reply, Petitioner argues that its proposed constructions are relevant to Patent Owner’s evidence of objective indicia of non-obviousness, including the alleged nexus. Reply 18–19 n.3. In light of our analysis below, because no determination in this Decision turns on whether we adopt Petitioner’s proposed constructions of “drill guide” and “fixation base,” we find that no express construction of these terms is required. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 12
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for petitioner
“substitution of the word ‘enclose’ for the term ‘surround.’” Sur-reply 6. We noted in the Institution Decision that “construing the claim term ‘surround’ to mean ‘enclose’ does not further inform or clarify to a person of ordinary skill in the art what is encompassed by the claim limitation.” Dec. 15. We reach the same conclusion here on the full record and find no basis to rewrite the Challenged Claims to replace “surround” with “enclose.” To the extent Patent Owner can be understood to suggest that we import additional limitations into the claims based on the exemplary figures in the ’209 patent, we decline to do so. Regardless, given the recognition by the Parties that “surround” and “enclose” are synonymous, our determinations in this Decision would have been the same had we adopted Patent Owner’s proposed definition of “surround” to mean “enclose.” Further, with regard to the claim language “configured and dimensioned to surround at least a portion of the teeth of the patient,” Patent Owner proposes construing “a portion of the teeth” as “at least some teeth.” Resp. 9 (citing Ex. 2007 ¶ 44). Patent Owner, however, offers no sufficient explanation in its Response to explain how why a “portion of the teeth” means “at least some teeth.” The Specification does not provide an explicit definition of “a portion of the teeth” and does not suggest an intention to use a meaning of the term “a portion of the teeth” that is particular to the ’209 patent. To the extent Patent Owner can be understood to imply that we should import additional limitations into the Challenged Claims based on the exemplary figures in the ’209 patent, we decline to do so. For that reason, alone, we decline to adopt Patent Owner’s proposed construction.” slip op. at 17
- Obviousness (§103) › Analogous artAnalogous artDecided for petitioner
“38; Sur-reply 9–10. First, Patent Owner argues that Sichuan is non-analogous art. Resp. 34–38. “To be considered within the prior art for purposes of the obviousness analysis, a reference must be analogous.” Circuit Check Inc. v. QXQ Inc., 795 F.3d 1331, 1335 (Fed. Cir. 2015) (citing Wang Labs., Inc. v. Toshiba Corp., 993 F.2d 858, 864 (Fed. Cir. 1993)). “Two separate tests define the scope of analogous prior art: (1) whether the art is from the same field of endeavor, regardless of the problem addressed and, (2) if the reference is not within the field of the inventor’s endeavor, whether the reference still is reasonably pertinent to the particular problem with which the inventor is involved.” Sanofi-Aventis Deutschland GmbH v. Mylan Pharms. Inc., 66 F.4th 1373, 1377 (Fed. Cir. 2023) (quoting In re Bigio, 381 F.3d 1320, 1325 (Fed. Cir. 2004)).” slip op. at 36
Patent outcomesUS 11,806,209 unpatentableClaim construction§ 103 obviousnesscites KSR · GrahamPatents in suitUS 11,806,209 - PTAB · Dec 16, 2025 · IPR2025-01046 · APJ Neil T Powell · IPR · Institution
The Board instituted IPR on claims 2–15, finding a reasonable likelihood that the 1946 Cyclopedia, Lindström, and Wong render at least claim 2 obvious; claim 1 was disclaimed.
RulingsInstitution decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Patent Owner responds that Petitioner’s proposed level of ordinary skill in the art is incorrect, “because design or analysis experience with other industrial wheeled vehicles would not necessarily be applicable to the art of the ’892 Patent.” Prelim. Resp. 12 (citing Ex. 2035 ¶¶ 38–39). According to Patent Owner, a person of ordinary skill in the art “would have at least a bachelor’s degree in a discipline related to mechanical engineering, physics, structural design, or an equivalent discipline, and at least two years of experience designing or analyzing rail cars.” Id. (citing Ex. 2035 ¶¶ 34, 38). The parties agree that one of ordinary skill in the art “would have had at least a bachelor’s degree in a discipline related to mechanical engineering, physics, structural design, or an equivalent discipline, and at least two years 5 Because Patent Owner statutorily disclaimed claim 1, this ground is moot. Patent Owner, however, disagrees that the experience should include designing or analyzing “similar vehicles.” Prelim. Resp. 12. At this stage, for the reasons below, limiting the ordinary skill in the art to “at least two years of experience designing or analyzing rail cars” does not affect our analysis of the parties’ dispute or our determination that there is a reasonable likelihood that Petitioner would prevail with respect to at least one of the challenged claims. Thus, based on the preliminary record, we adopt Petitioner’s proposed level of ordinary skill to determine whether review should be instituted.” slip op. at 12
- Expert testimonyPetitioner expert creditedDecided for petitioner
“Patent Owner also argues that Petitioner’s declarant does not have “actual industry experience with railcar structures” and, thus, “makes the wrong conclusions and conflates various concepts that a [person of ordinary skill in the art] with practical industry experience and knowledge would not.” Prelim. Resp. 12–13 (citing Ex. 2035 ¶ 39). For the reasons discussed below, in our preliminary analysis, we give credit to the cited testimony of Petitioner’s declarant, because it finds support in the relied-upon portions of the record.” slip op. at 13
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“At this stage, we need not construe expressly any claim term to resolve the parties’ dispute regarding whether Petitioner has demonstrated a reasonable likelihood of prevailing on at least one challenged claim. Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms that . . . are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))” slip op. at 14
- Obviousness (§103) › Analogous artAnalogous artDecided for petitioner
“been obvious over the 1946 Cyclopedia and Wong. Weighing the parties’ arguments and evidence, we find Petitioner provides sufficient rational underpinning for its assertion that it would have been obvious in view of Wong to implement a cross-wise extending beam to reinforce the 1946 Cyclopedia’s NSC ore car’s end slope sheet. Pet. 52–53; Prelim. Resp. 28– 30. In response to Petitioner’s assertion that “[t]he upper, outboard end of [Wong’s slope sheet 26] is reinforced by a cross-wise, L-shaped beam positioned under the slope sheet,” Patent Owner argues that “Wong does not provide reinforcement, but simply shows two sheets being connected for lading containment and load transfer.” Pet. 52; Prelim. Resp. 29. At this stage, we find Petitioner has the better position. Although we agree with Patent Owner that Wong shows two sheets connected to one another, that does not negate Petitioner’s correct observation that Wong shows an upper end of its end slope sheet 26 resting on an L-shaped structure, which apparently would reinforce end slope sheet. Pet. 52; Ex. 1003 ¶ 56. reason to look to Wong in the first place,” we again find that Petitioner has the better position at this stage. Prelim. Resp. 29. For example, Wong’s disclosure of “hopper railcar 10” (Ex. 1006, 3:6–9) and the 1946 Cyclopedia’s disclosure of “Freight Cars: Hopper Ore” (Ex. 1004, 27–28; Ex. 1054, 27–28) support Petitioner’s position that “Wong and the 1946 Cyclopedia are in the same field.” Pet. 52; see also id. at 76 (“Wong discloses a rail road hopper car (‘hopper railcar’ 10)”), 18–19 (“The ore-car section of the 1946 Cyclopedia—entitled ‘Freight Cars: Hopper Ore’— contains drawings and a photograph of an ore car manufactured by Patent Owner NSC.”); Ex. 1003 ¶ 56 (“Wong and the 1946 Cyclopedia are in the same field of hopper railcars”) (citing Ex. 1004, 27–28; Ex. 1006, code [57]). This position is not persuasively rebutted by Patent Owner’s argument that Wong’s hopper railcar 10 uses aluminum and steel together for certain reasons. Prelim. Resp. 28–29.” slip op. at 23
Claim construction§ 103 obviousnesscites Phillips · KSRPatents in suitUS 8,166,892 - PTAB · Dec 16, 2025 · IPR2025-01047 · APJ Hyun J Jung · IPR · Institution
The Board instituted IPR of claims 1–44 on all presented challenges, finding a reasonable likelihood that FreightCar would prevail on at least one claim based on Hart, the 1906 Cyclopedia, and Wong.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“instituted “unless . . . there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” Upon consideration of the Petition and for the reasons explained below, we determine that Petitioner has shown a reasonable likelihood of prevailing with respect to at least one of the challenged claims. Thus, we institute an inter partes review of claims 1–44 of the ’515 patent on all presented challenges. 37 C.F.R. § 42.108(a) (2024) (“When instituting . . . review, the Board will authorize the review to proceed on all of the challenged claims and on all grounds of unpatentability asserted for each claim.”); see also SAS Inst. Inc. v. Iancu, 138 S. Ct. 1348, 1359–60 (2018).” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“The parties agree that one of ordinary skill in the art “would have had at least a bachelor’s degree in a discipline related to mechanical engineering, physics, structural design, or an equivalent discipline, and at least two years of experience designing or analyzing rail cars.” Pet. 29; Prelim. Resp. 9. Patent Owner, however, disagrees that the experience should include designing or analyzing “similar vehicles.” Prelim. Resp. 9. At this stage, for the reasons below, limiting the ordinary skill in the art to “at least two years of experience designing or analyzing rail cars” does not affect our analysis of the parties’ dispute or our determination that there is a reasonable likelihood that Petitioner would prevail with respect to at least one of the challenged claims. Thus, based on the preliminary record, we adopt Petitioner’s proposed level of ordinary skill to determine whether review should be instituted. Patent Owner also argues that Petitioner’s declarant does not have “actual industry experience with railcar structures” and, thus, “makes the wrong conclusions and conflates various concepts that a [person of ordinary skill in the art] with practical industry experience and knowledge of rail cars would not.” Prelim. Resp. 9–10 (citing Ex. 2035 ¶ 35). For the reasons discussed below, in our preliminary analysis, we give credit to the cited testimony of Petitioner’s declarant, because it finds support in the relied-upon portions of the record.” slip op. at 10
- Expert testimonyPetitioner expert creditedDecided for petitioner
“Patent Owner also argues that Petitioner’s declarant does not have “actual industry experience with railcar structures” and, thus, “makes the wrong conclusions and conflates various concepts that a [person of ordinary skill in the art] with practical industry experience and knowledge of rail cars would not.” Prelim. Resp. 9–10 (citing Ex. 2035 ¶ 35). For the reasons discussed below, in our preliminary analysis, we give credit to the cited testimony of Petitioner’s declarant, because it finds support in the relied-upon portions of the record.” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundInstituted
“to further support the upper, outboard end of the slope sheet with a crosswise, L-shaped beam as in Wong,” and one of ordinary skill in the art would have been motivated to do so, because of “the benefits of reinforcing the slope sheet at its upper end, where its connection with another structure creates a stress concentration.” Pet. 63 (citing Ex. 1003 ¶ 108). Petitioner points to Hart’s transverse beam b3 and argues that it suggests using a transverse beam like Wong if Hart is modified so that upper beam b3 no longer supports the slope sheet. Id. (citing Ex. 1008, Fig. 1). Petitioner also argues that the references are in the same field and that there would have been a reasonable expectation of success. Id. at 63–64 (citing Ex. 1003 ¶ 108; Ex. 1008, Fig. 1). Based on the preliminary record, Petitioner shows that its proposed combination of Hart, the 1906 Cyclopedia, and Wong teaches or suggests the above-quoted limitations of claim 24 and that one of ordinary skill in the art would have combined those references in the manner asserted with a reasonable expectation of success.” slip op. at 19
§ 103 obviousnesscites Phillips · KSRPatents in suitUS 8,132,515 - Samsung Electronics Co., Ltd. / Samsung Electronics America, Inc. v. Ouraring, Inc.All claims unpatentablePTAB · Dec 2, 2025 · IPR2024-00928 · APJ Neil T Powell · IPR · Final written decision
Claims 1–5, 11–13, and 16–18 are unpatentable as obvious over Schröder and Yuen, LeBoeuf, or LeBoeuf and Wissmar; Schröder alone did not render its challenged claims unpatentable.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedOther
“Patent Owner agrees with Petitioner’s proposed definition of a person of ordinary skill in the art. PO Resp. 14. We adopt this uncontested definition of the level of ordinary skill in the art. This definition is supported by the record and consistent with the disclosure in the ’034 patent and the references cited in the Petition.” slip op. at 9
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner
“Petitioner has the better position, as we agree with Petitioner that the ’034 patent discloses an embodiment that uses transparent potting as a window, rather than to form the overall form factor and encapsulate components: [Figure] 16C is a perspective view of the WCD with potting material 1630. As described above, the PCB, battery, and components can be disposed within the space. Once disposed therein, a potting 1630 can be provided atop the components and within the cutaway portion 1616. The potting 1630 can be transparent to allow for transmission of light through the cutaway portions 1616. Ex. 1001, 20:51–57. This configuration is shown below in Figure 16C. “[Figure] 16C is a perspective view of the WCD with potting material.” Ex. 1001, 6:1–2. As Figure 16C shows, potting material 1616 forms a window in only a portion of the WCD’s exterior. can be used to encapsulate components and form the overall form factor in some embodiments. E.g., Ex. 1001, 17:4–8, 18:61–62. But Patent Owner does not persuade us that claim 12 is limited to those embodiments. PO Resp. 29; SuperGuide Corp. v. DirecTV Enters., Inc., 358 F.3d 870, 875 (Fed. Cir. 2004) (“Though understanding the claim language may be aided by the explanations contained in the written description, it is important not to import into a claim limitations that are not part of the claim.”). Accordingly, we do not construe claim 12’s “external transparent potting” as requiring material that “forms the ‘overall form factor of the WCD 120, in addition to providing a housing for one or more electronic components,’” as suggested by Patent Owner. PO Resp. 29. Nor do we construe the claim language as requiring material that “also fills the space and encapsulates the components,” as suggested by Patent Owner. Id.” slip op. at 11
- Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable
“We are not persuaded by Petitioner’s arguments and find that Patent Owner has the better position. Although Schröder describes some aspects that are similar to those of a printed circuit board, Petitioner has not sufficiently demonstrated that a person having ordinary skill in the art would understand Schröder’s inlay 12 or carrier foil to be a “printed circuit board,” as recited in independent claims 1, 11, and 16. As an initial matter, while Schröder refers to a “circuit board” in another context, it never refers to the carrier foil or inlay in its finger-ring embodiment as such. See Ex. 1007, 22:48–49; see also Ex. 1079 ¶ 21 (Dr. Anthony acknowledging that Schröder’s only reference to a “circuit board” is “unrelated to Schröder’s finger-ring teachings”). Instead, Schröder describes features of that inlay, explaining that “[t]he carrier foil itself consists of a flexible plastic material, e.g.[,] PET or Kapton” and “antenna coil 8 can for example be printed on the carrier foil by means of a conductive paste” and “a depression is manufactured in the carrier foil, e.g.[,] by milling, lasering, etching, before the chip module 10, the antenna coil 8 and optional further electronic devices are inserted into the depression.” Ex. 1007, 13:26–31, 13:35–37. Schröder further describes that “[a]t least one further foil can be applied to the carrier foil or the ring blank on at least one side” to produce a “multilayer foil composite” that can be “interconnected” by means of “glue” slip op. at 23
- Expert testimonyPetitioner expert discountedOther
“show that Schröder’s inlay 12 is a PCB. Relying on testimony from Dr. Anthony, Petitioner asserts that Schröder’s inlay 12 serves as a flexible carrier made of materials “commonly understood to be printed circuit board materials” such as PET and Kapton. Pet. 23 (citing Ex. 1002 ¶ 172; Ex. 1006, 12:28–29). Dr. Anthony did not provide a clear explanation of a person of ordinary skill in the art’s understanding of a PCB in his direct testimony. article describing a PCB as a “laminated sandwich structure of conductive and insulating layers” was an accurate description of a PCB: Q. So is the first sentence of this Wiki page, in your mind, an accurate description of a printed circuit board? A. So, the first sentence, “A printed circuit board (PCB)[] also called [a] printed wiring board, []is a laminated sandwich structure of conductive and insulating layers, each with a pattern of traces, planes, and other features (similar to wires on a flat surface) etched from one or more sheets of copper laminated onto or between sheet layers of nonconductive substrate.” And so your question again was? Q. Is that a fair definition of printed circuit board in your mind? A. It’s a fair description of the general process for circuit boards, layers of conductive traces.” slip op. at 21
Patent outcomesUS 9,582,034 unpatentableClaim construction§ 103 obviousnessPatents in suitUS 9,582,034
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.