• Savant Technologies LLC D/B/A GE Lighting / Elong International USA Inc. et al. v. Feit Electric Company, Inc.All claims unpatentable
  PTAB · Sep 14, 2026 · IPR2025-00698 · APJ Kevin W Cherry · IPR · Final written decision

  Claims 1–11, 18–20, 23–25, and 28 are unpatentable as obvious over the two combinations of prior art.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Thus, we adopt Petitioner’s articulation of the level of ordinary skill in the art, which is consistent with the ’539 patent and the asserted prior art, and we apply it in our obviousness analysis below.” slip op. at 9

  • Expert testimonyPetitioner expert creditedDecided for petitioner

    “¶ 39). Petitioner further relies on Stokes to teach an average particle size that preferentially scatter blue . . . LED light as compared to yellow . . . light from the luminescent material.” Id. at 26–27 (citing Ex. 1108, 7:1–4). Petitioner argues that “a POSA would have been motivated to apply this principle to Krummacher, because it would increase the conversion of blue light to yellow light and improve the uniformity of the light source.” Id. at 27 (citing Ex. 1102 ¶ 237). Petitioner notes that “[c]onversion of blue light to yellow light is improved by maximizing the scattering of blue light.” Id. In addition, Petitioner asserts that “[u]niformity is improved by preferentially scattering the concentrated light from the blue-light LED chip instead of the disperse light emitted by the phosphor.” Id. at 28 (citing Ex. 1102 ¶ 237). Petitioner contends that “[a] POSA would have had a reasonable expectation of success applying this principle to Krummacher, because the relevant particle size range includes the range disclosed by Krummacher.” Id. Petitioner argues that “[a] POSA would have recognized selecting an average particle size as a design decision to be made based on a number of factors, including the light scattering properties of the particles, and well within the skill of the art.” Id. (citing Ex. 1102 ¶ 238). We find this explanation and the supporting testimony of Dr. Doolittle well-reasoned and supported and entitled to significant weight. Thus, we find that Petitioner has shown by a preponderance of the evidence that the combination of Krummacher and Stokes teaches limitation 1[c], and that a person of ordinary skill in the art would have been motivated to combine the references in the manner proposed.” slip op. at 40

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “¶ 39). Petitioner further relies on Stokes to teach an average particle size that preferentially scatter blue . . . LED light as compared to yellow . . . light from the luminescent material.” Id. at 26–27 (citing Ex. 1108, 7:1–4). Petitioner argues that “a POSA would have been motivated to apply this principle to Krummacher, because it would increase the conversion of blue light to yellow light and improve the uniformity of the light source.” Id. at 27 (citing Ex. 1102 ¶ 237). Petitioner notes that “[c]onversion of blue light to yellow light is improved by maximizing the scattering of blue light.” Id. In addition, Petitioner asserts that “[u]niformity is improved by preferentially scattering the concentrated light from the blue-light LED chip instead of the disperse light emitted by the phosphor.” Id. at 28 (citing Ex. 1102 ¶ 237). Petitioner contends that “[a] POSA would have had a reasonable expectation of success applying this principle to Krummacher, because the relevant particle size range includes the range disclosed by Krummacher.” Id. Petitioner argues that “[a] POSA would have recognized selecting an average particle size as a design decision to be made based on a number of factors, including the light scattering properties of the particles, and well within the skill of the art.” Id. (citing Ex. 1102 ¶ 238). We find this explanation and the supporting testimony of Dr. Doolittle well-reasoned and supported and entitled to significant weight. Thus, we find that Petitioner has shown by a preponderance of the evidence that the combination of Krummacher and Stokes teaches limitation 1[c], and that a person of ordinary skill in the art would have been motivated to combine the references in the manner proposed.” slip op. at 40

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightMotivation foundDecided for petitioner

    “Finally, we do not agree with Patent Owner that “quantum efficiency” would have dissuaded a person of ordinary skill from making the combination. PO Resp. 36–38. To begin with, “[i]t’s not necessary to show that a combination is the best option, only that it be a suitable option.” Intel Corp. v. Qualcomm Inc., 21 F.4th 784, 800 (Fed. Cir. 2021). Here, as demonstrated by, at least, Shimizu and Stokes, blue LEDs in this wavelength range were known to work as light sources for white-light LEDs. See Pet. 30–31. Additionally, we find persuasive Petitioner’s evidence that a person of ordinary skill in the art would not have been concerned solely with quantum efficiency, but also with overall luminous efficacy of a complete white LED package. Reply 9. As Dr. Schubert’s textbook explains, A fundamental drawback of UV pumped white LEDs is the energy loss (Stoke’s shift). The potential luminous efficacy of UV pumped white LED lamps is, therefore, markedly lower than that of white sources based on a blue LED exciting a yellow phosphor. Ex. 2014, 358–59; see also Ex. 1148, 87:5–88:4 (acknowledging Stokes shift). Thus, the evidence shows that, whatever gain in quantum efficiency a lower wavelength might offer, there were other drawbacks that a person of ordinary skill would have to balance. But “a given course of action often has simultaneous advantages and disadvantages, and this does not necessarily obviate motivation to combine.” Medichem, 437 F.3d at 1165. Indeed, Petitioner has shown several references—including, Shimizu and Stokes—that made this tradeoff. Moreover, “[o]bviousness does not require absolute predictability of success. . . . [A]ll that is required is a reasonable expectation of success.” In re O’Farrell, 853 F.2d 894, 903–04 (Fed. Cir. 1988). We find that the prior art of record demonstrates that a person of ordinary skill in the art at the time of the invention would have such an expectation in making the combination of Krummacher, Stokes, and Shimizu. Accordingly, we find that Petitioner has shown by a preponderance of the evidence that there would have been motivation to combine Krummacher, Stokes, and Shimizu with a reasonable expectation of success.” slip op. at 43

  Patent outcomesUS 8,614,539 unpatentable
  § 103 obviousnesscites Phillips · Graham
  Patents in suitUS 8,614,539
• Tesla, Inc. v. Charge Fusion Technologies, LLCAll claims unpatentable
  PTAB · Jul 13, 2026 · IPR2025-00153 · APJ Carl M Defranco · IPR · Final written decision

  Claims 1–30 are unpatentable as obvious under § 103 over the asserted combinations of prior art.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “understanding of one of ordinary skill in the art at the time of the invention. Tesla submits that one of ordinary skill in the art would have had at least a bachelor’s degree in electrical or mechanical engineering (or an equivalent field) and at least two years of work experience involving automotive systems, including electric vehicle power management. . . . Additional industry 1 US 2009/0313034 A1, pub. Dec. 17, 2009 (Ex. 1004, “Ferro”). 2 EP 1,920,968 A1, pub. May 14, 2008 (Ex. 1005, “Oyobe”). 3 US 7,124,691 B2, iss. Oct. 24, 2006 (Ex. 1006, “Donnelly”). 4 Steven E. Letendre, The V2G Concept: A New Model for Power? PUBLIC UTILITIES FORTNIGHTLY, Feb. 15, 2002, at 16 (Ex. 1007, “Letendre”). 5 US 5,654,621, iss. Aug. 5, 1997 (Ex. 1078, “Seelig”). 6 US 6,662,083 B1, iss. Sep. 16, 2003 (Ex. 1010, “Knockeart”). experience or technical training may offset less formal education, while advanced degrees or additional formal education may offset lesser levels of industry experience. Pet. 2 (citing Ex. 1003 ¶¶ 14–15). Charge Fusion “takes no position with respect to Petitioner’s proposed level of ordinary skill.” PO Resp. 17. For purposes of our analysis, we apply Tesla’s proposed level of ordinary skill, which we find to be consistent with the problems addressed in the ’987 patent and the prior art. B. Claim Interpretation” slip op. at 6

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “1. “dynamic attribute of an electric charge provider” In the Petition, Tesla proposes that we construe “dynamic attribute of an electric charge provider,” as recited in every independent claim, to mean “a changing or otherwise fluctuating cost (or price) of electricity for purchase from an electric charge provider.” Pet. 4–5. Charge Fusion responds that Tesla improperly narrows the meaning of this claim limitation. PO Resp. 15 (arguing this claim term “is not just limited to ‘changing or otherwise fluctuating cost (or price)’ as alleged by the Petition” (emphasis added)). Although we consider Tesla’s proposed construction to identify an exemplary “dynamic attribute of an electric charge provider,” we see no need to limit the meaning of this limitation as proposed by Tesla. Indeed, Tesla agrees. See Pet. Reply. 7 (arguing only that this claim limitation “at least includes” such an example). And Charge Fusion does not contend otherwise. See PO Resp 15 (arguing only that this limitation “is not just limited to” cost fluctuations). As such, we see no need to further construe this claim limitation. 2. “determine . . . a charging schedule for the vehicle” Limitation 1[g] recites “determine, based at least on the one or more charging preferences and at least one current value of a dynamic attribute of an electric charge provider, a charging schedule for the vehicle.” Independent claim 8, 15, and 22 recite a materially identical limitation. Tesla submits that this limitation should not be construed as a means-plus- function limitation under 35 U.S.C. § 112(6). See Pet. 5. Charge Fusion agrees that “nothing in the claim invokes [§] 112(6).” PO Resp. 16. As such, we discern no dispute regarding the meaning of this claim limitation.” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “Initially, we note that, as claimed, there is no express restriction on the manner in which the “amount” or “charge” is specified or otherwise expressed. Indeed, the Specification uses both “desired charge percent level” and “desired charge range level” as alternative ways for a user to specify an “amount of charge.” Ex. 1001, 14:53–15:8 (emphases added). The Specification defines “desired charge range level” as meaning “a desired distance to travel.” Id. at 15:3–8. Elsewhere, the Specification describes that a user may specify the amount of charge as follows: “the user may indicate a desired charging level (and/or a desired charging level may be automatically calculated) based on a desired distance of travel.” Id. at 19:49–57 (emphasis added). More specifically, annotated Figure 7 of the ’987 patent, reproduced below, demonstrates how a user may select “amount of charge” in terms of a desired mileage range 720 or a percentage level 718. See Pet. Reply 2. As shown in red, annotated Figure 7 illustrates that a user selects “desired charge level 720” on “vehicle charge indicator 714” by moving a slider to a value specified in “miles” (e.g., 110 miles). The Specification, after discussing selecting a desired charge percent level 718, explains: The user may also or alternatively view and/or change the desired charge range level 720. An estimate of how far the vehicle can travel on a given charge amount (which may be a general average and/or may be computed based on a specific itinerary and/or past driving habits) can be determined, for example, and utilized to express the desired charge level in terms of distance capable of being traveled. In such a manner, for example, a user may determine a desired distance to travel (e.g., how far it is from home to work or vice versa) and may set the desired charge range level 720 to match the desired distance. Ex. 1001, 14:65–15:8. Thus, the Specification confirms that “amount of charge” may be expressed in terms of a desired mileage as well as a desired percentage level.” slip op. at 11

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightMotivation foundDecided for petitioner

    “We disagree. Charge Fusion’s reliance on Wonderland is misplaced and does not support the proposition for which it is cited. In Wonderland, the district court denied the accused infringer’s motion for summary judgment of invalidity, in part, because genuine issues of material fact existed as to whether there was sufficient motivation to combine the prior art. Wonderland, 988 F. Supp. 2d at 511. As such, the district court’s Wonderland decision does not constitute a final ruling on the motivation to combine issue, and the Federal Circuit’s summary affirmance of the district court’s ruling neither addresses the issue nor reflects how the issue was resolved at trial. See Wonderland NurseryGoods Co. v. Thorley Indus., LLC, 644 F. App’x 1011 (Fed. Cir. 2016). Moreover, contrary to Charge Fusion’s assertion, Tesla correctly notes that although Ferro refers to wireless charging, it provides no implementation details. Ex. 1004 ¶ 36; Ex. 2006, 54:8–55:9. Nonetheless, Ferro does describe manual options for initiating charging, and Tesla’s expert credibly testifies that one of ordinary skill in the art would have been motivated to apply Oyobe’s vehicle sensor to allow a user to initiate Ferro’s charging methods more easily without having to leave the vehicle. See Ex. 1003 ¶¶ 146, 151, 152 (citing Ex. 1004 ¶ 109). Accordingly, we find that Tesla establishes that one of ordinary skill in the art would have been motivated to incorporate Oyobe’s use of a sensor to establish presence of a vehicle near a charging station into Ferro’s system.” slip op. at 17

  Patent outcomesUS 11,631,987 unpatentable
  Claim construction§ 103 obviousnesscites Phillips
  Patents in suitUS 11,631,987
• Tesla, Inc. v. Charge Fusion Technologies, LLCAll claims unpatentable
  PTAB · Jul 13, 2026 · IPR2025-00152 · APJ Carl M Defranco · IPR · Final written decision

  Claims 1–17 are unpatentable as obvious: claims 1–4, 6–9, and 11–14 over Sutardja, Donnelly, and Letendre; claims 5, 10, and 15 with Seelig; claims 16 and 17 with Knockeart.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “understanding of one of ordinary skill in the art at the time of the invention. Tesla submits that one of ordinary skill in the art would have had at least a bachelor’s degree in electrical or mechanical engineering (or an equivalent field) and at least two years of work experience involving automotive systems, including electric vehicle power management. . . . Additional industry experience or technical training may offset less formal education, 1 US 2008/0136371 A1, pub. Jun. 12, 2008 (Ex. 1011, “Sutardja”). 2 US 7,124,691 B2, iss. Oct. 24, 2006 (Ex. 1006, “Donnelly”). 3 Steven E. Letendre, The V2G Concept: A New Model for Power? PUBLIC UTILITIES FORTNIGHTLY, Feb. 15, 2002, at 16 (Ex. 1007, “Letendre”). 4 US 5,654,621, iss. Aug. 5, 1997 (Ex. 1078, “Seelig”). 5 US 6,622,083 B1, iss. Sep. 16, 2003 (Ex. 1010, “Knockeart”). while advanced degrees or additional formal education may offset lesser levels of industry experience. Pet. 2–3 (citing Ex. 1003 ¶ 29). Charge Fusion “takes no position with respect to Petitioner’s proposed level of ordinary skill in the art.” PO Resp. 9. For purposes of our analysis, we apply Tesla’s proposed level of ordinary skill, which we find to be consistent with the problems addressed in the ’788 patent and the prior art. B. Claim Interpretation” slip op. at 6

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

    “shown in Figure 7 of the ’788 patent. Pet. 4–5. Charge Fusion responds that Tesla’s proposed construction should be rejected because it “wrongly import[s] embodiments from the specification.” PO Resp. 14–16. We discern no dispute over the meaning of “unitary vehicle charge indicator” because, contrary to what Charge Fusion argues, Tesla does not contend that this limitation is “required to be limited to” the bar graph embodiment of Figure 7, only that it “at least includes” that embodiment. Compare Pet. 5, with PO Resp. 14–16. Tesla also argues that the “first” and “second” portions of the unitary vehicle charge indicator—which indicate the charged and uncharged capacities of the battery—recite merely “communicative content,” and thus, are “not entitled to any patentable weight” because they are directed to nonfunctional printed matter. Pet. 5–7 (citing various case law). At the same time, however, Tesla maintains that “[r]egardless, Donnelly teaches a bar graph indicating the amount of charge and uncharged capacity.” Pet. Reply 11–12 (citing Pet. 33–34); see also Hrg. Tr. 74:22–25, 75:9–11. For reasons expressed below, we agree that Tesla persuasively demonstrates that the asserted combination teaches the “unitary vehicle charge indicator element” as claimed and construed by Charge Fusion. Accordingly, we need not decide the printed matter issue.” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “Initially, we note that, as claimed, there is no express restriction on the manner in which the “amount” or “charge” is specified or otherwise expressed. Indeed, the Specification uses both “desired charge percent level” and “desired charge range level” as alternative ways for a user to specify an “amount of charge.” Ex. 1001, 14:63–15:18 (emphases added). In particular, the Specification defines “desired charge range level” as meaning “a desired distance to travel.” Id. at 15:8–18. Elsewhere, the Specification describes that a user may specify the amount of charge as follows: “the user may indicate a desired charging level (and/or a desired charging level may be automatically calculated) based on a desired distance of travel.” Id. at 19:59–67 (emphasis added).” slip op. at 9

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable

    “full charge” for the battery, and thus, Tesla fails to explain how the combination of Sutardja with Donnelly’s battery bar graph image “would allow a user to select a specific amount of charge or how this would result in a unitary vehicle charge indicator,” as claimed. PO Resp. 30. According to Charge Fusion, “[l]imiting the single option of ‘full charge’ as described in Sutardja would defeat the purpose of implementing a slider” as taught by Donnelly. Id. (citing Ex. 2008 ¶ 72). We disagree. Charge Fusion’s argument rests on the mistaken premise that Sutardja only contemplates selecting a full amount of charge for the battery and not an amount below a full charge, i.e., a partial charge. But that is not what Sutardja says. More accurately, Sutardja teaches that the user specifies the amount of charge—"The user interface module 108 may comprise a key pad, a display, a microphone, and/or a speaker (all not shown). A user of the vehicle 102-1 may use the user interface module 108 to set charging parameters for charging the battery 14.” Ex. 1011 ¶ 243. Elsewhere, Sutardja teaches that the user may set a “predetermined level” of charge— The charge monitoring module 150 may inform the control module 112 when the battery 14 is charged to a predetermined level (e.g., full charge) that may be indicated in the charging parameters. Subsequently, the charge monitoring module 150 may stop charging the battery 14 by deactivating the converter 156 and the charging module 152. The power meter 24 may measure the amount of power received from the utility company 23 during the charging operation. Id. ¶ 270 (emphases added). Although that passage indicates that a “full charge” is an example of a “predetermined level” of charge, nowhere does it exclude the selection of a lesser amount. Indeed, the passage contemplates the ability to “stop charging the battery,” which indicates that selection of the predetermined level may be less than a full charge. Id. Thus, we are not persuaded by Charge Fusion’s argument to the contrary. Rather, in our view, Tesla demonstrates by a preponderance of the evidence that the Sutardja-Donnelly combination teaches a “unitary vehicle charge indicator” that includes at least “first” and “second” portions and that one of ordinary skill in the art would have had reason to successfully combine their respective teachings in a manner that allows a user to predetermine, i.e., specify, an amount of charge. slip op. at 17

  Patent outcomesUS 11,990,788 unpatentable
  Claim construction§ 103 obviousnesscites Phillips
  Patents in suitUS 11,990,788
• Resmed Corp. v. Cleveland Medical Devices, Inc.All claims unpatentable
  PTAB · Jun 29, 2026 · IPR2025-00246 · APJ Cynthia M Hardman · IPR · Final written decision

  Claims 15–29 are unpatentable as obvious over the asserted combinations; the contingent motion to amend claims 30–41 is denied for lack of written-description support.

  RulingsFinal written decision

  • PTAB / AIA Trials › Real party in interest / privityRpi dispute resolved for petitionerDecided for petitioner

    “Patent Owner filed an authorized Motion to Terminate, alleging that Petitioner failed to name its corporate parent, ResMed Inc., as a real party in interest. Paper 39. Petitioner filed an opposition. Paper 42. Patent Owner filed a reply. Paper 43. We denied the Motion to Terminate. Paper 51.” slip op. at 3

  • Skill levelSkill level board ownOther

    “understanding of a person of ordinary skill in the art at the time the invention was made.10 See Graham, 383 U.S. at 17–18. The parties agree that a person of ordinary skill in the art (sometimes referred to herein as “POSITA”) would have had: at least a bachelor’s degree in mechanical engineering, electrical engineering, computer science, biomedical engineering, or a similar technical field, with at least two years of relevant product design experience working with diagnostic sensor systems and network data systems, such as networked PAP machines. Additional experience could substitute for less education, and additional education could likewise substitute for less experience. Pet. 3–4 (citing Ex. 1003 (Kirkness Decl.) ¶ 44); PO Resp. 4. 9 Patent Owner does not assert any objective indicia of nonobviousness. See generally PO Resp. 10 For purposes of this Decision, we apply a priority date of November 4, 2005. See supra n.4. Because the proposed level of ordinary skill in the art is consistent with the cited prior art and is undisputed on this record, we adopt it for purposes of this Decision. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (indicating that the prior art itself may reflect an appropriate skill level).” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Patent Owner does not persuade us to construe the term as “a value [or calculated value] that indicates how dire a patient’s symptoms are.” Patent Owner points to nothing in the intrinsic record that purportedly supports this construction, and we agree with Petitioner that “the patent specification’s disclosures regarding determining a level of symptom severity are broad, establishing that it can generally be derived from any sensor data and/or breathing events.” Pet. Reply 3–4; see also Ex. 1001, 3:44–46 (“Signals from the[] sensors are then analyzed to determine the level of severity of the symptoms of the subject’s sleep disorder.”). Patent Owner relies only on expert declarations to support its construction. But as indicated by the Federal Circuit, extrinsic evidence is “less significant than the intrinsic record in determining ‘the legally operative meaning of claim language.’” Phillips v. AWH Corp., 415 F.3d 1303, 1317 (Fed. Cir. 2005). This is especially applicable here, where neither Dr. D’Ambrosio’s nor Dr. Schwartz’s declaration was prepared for this proceeding, and neither declarant was subject to cross examination on their opinions. Moreover, neither of the declarants was opining on claim construction; rather, they were addressing indefiniteness and/or written description issues. See Ex. 1058 at 7 (heading addressing definiteness); Ex. 2026 at 18 (heading addressing written description). Further, Dr. Schwartz appears to have been making an argument about certain patent claims (not the challenged ’333 patent) based on Patent Owner’s own statements made during prosecution of a separate patent application. See Ex. 2026 ¶ 47 (“[T]he similar term used in the ’284 patent claims (‘data of severity of sleep disorder symptoms’) does not find written description support in the specification by a disclosure of the same statistics disclosed in Wright, because CleveMed argued those statistics are not related to severity of sleep disorder symptoms.” (emphasis added)). Patent Owner has not persuaded us that Dr. Schwartz’s testimony has direct applicability to the claim term at issue here. Dr. Borkholder’s testimony is likewise unpersuasive. Aside from citing Dr. D’Ambrosio’s and Dr. Schwartz’s declarations, Dr. Borkholder cites Exhibits 2027 and 2016. These exhibits discuss indices such as AHI and RDI that are used to assess the severity of a patient’s symptoms, but Patent Owner has not adequately explained how they bear on construction of the claim term at issue here, which is not addressed in these exhibits. Ex. 2022 ¶¶ 32–33. Accordingly, we accord Dr. Borkholder’s claim construction opinions little weight, because they are unsupported by reference to objective, corroborating evidence of record. See, e.g., Ashland Oil, Inc. v. Delta Resins & Refractories, Inc., 776 F.2d 281, 294 (Fed. Cir. 1985) (“Lack of factual support for expert opinion going to factual determinations . . . may render the testimony of little probative value in a validity determination.”); Xerox Corp. v. Bytemark, IPR2022-00624, Paper 9, 15 (PTAB 2023) (precedential) (explaining that declaration testimony that “is conclusory and unsupported” and which “adds little to the conclusory assertion for which it is offered to support . . . is entitled to little weight”).” slip op. at 23

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable

    “We find that Petitioner has the better argument. Tidal volume refers to “the volume of air that is inspired or expired during a respiratory cycle.” Ex. 2028, 13–14; PO Resp. 10. “[H]ypopnea events are defined as a reduction of ≥50 % or 74 % in tidal volume from baseline and apnea events as absence of tidal volume for at least 10s.” Ex. 2028, 13–14 (emphasis omitted). Toge teaches that a control unit analyzes collected data (e.g., the flow rate) and calculates tidal volume. Ex. 1044 (Toge) ¶¶ 34–38. The calculated tidal volume is “a quantified level of severity data based on the subject’s sleep apnea symptoms during the therapy” because it represents, e.g., the “level of airway obstruction the patient experiences during the sleep apnea treatment using the PAP device.” Pet. 15. As Dr. Chatterjee explains: Toge discloses that tidal volume Fp is a quantified level of data because Toge discloses that Fp is monitored with respect to threshold values (id., [0051]) and because Fp is a function of Ft, Fa, and Fb, which are quantitative values. Toge discloses that tidal volume Fp is severity data because Toge discloses that tidal volume is indicative of whether the patient’s breathing warrants “emergency measures” (id., [0039]) and whether to “send an alert” in “an emergency where the patient’s breathing has drastically weakened” (id., [0055]). . . . . Because Toge discloses determining tidal volume (determine a quantified level of severity data) based on Ft, Fa, and Fb (id., [0035]), which corresponds to the subject’s condition (subject’s sleep apnea symptoms) while using the device (during the therapy) (id., [0036], [0037]), Toge discloses determin[ing] a quantified level of severity data based on the subject’s sleep apnea symptoms during the therapy. Ex. 1005 (Chatterjee Decl.) ¶¶ 122–125. Patent Owner’s attempt to dismiss tidal volume as a mere “breathing metric” is unavailing. First, Petitioner correctly “notes that in the paragraph PO cites to in Dr. Schwartz’s declaration, he indicates that breathing metrics are a level of severity data.” Pet. Reply 8 (citing Ex. 2026 ¶ 46 (“standard sleep disordered breathing metrics” [ ] were well validated indicators of the type and severity of sleep disordered breathing”)). Second, Dr. Kirkness explains that tidal volume represents the level of airway obstruction, e.g., apnea “is the most severe form of reduction in airflow [and] the absence of airflow results in quantified tidal volume of zero milliliters per breath.” Ex. 1003 (Kirkness Decl.) ¶¶ 157, 159; see also PO Resp. 10–11 (Patent Owner recognizing that an apnea is defined as absence of tidal volume for at least 10 seconds). The calculated tidal volume thus indicates severity because it is used to adjust the PAP system, e.g., in the case of decreasing tidal volume, a medical professional can change the airflow settings “to counter/treat the more severe level of airway obstruction observed from the decreasing tidal volume.” Ex. 1003 (Kirkness Decl.) ¶ 158; Pet. 15–16; Ex. 1044 (Toge) ¶ 39.” slip op. at 26

  Patent outcomesUS 11,857,333 unpatentable
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,857,333
• Nxtgen Toys, LLC v. Zipstring, LLCAll claims unpatentable
  PTAB · Feb 20, 2026 · IPR2024-01213 · APJ Richard H Marschall · IPR · Final written decision

  Claims 1–4, 12, and 15–17 are unpatentable; substitute claim 27 is allowed, while substitute claims 21–26 and 28 are denied as obvious.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person having ordinary skill in the art at the time of the invention “was typically a person with a bachelor’s degree in mechanical engineering, aerospace engineering, physics, or other science or 6 Patent Owner does not rely on any objective indicia of nonobviousness in this proceeding. engineering based degree that [was] familiar with general principles of mechanics and aerodynamics with at least two years of experience in product design and development in the field of toys or other amusement type devices.” Pet. 32 (citing Ex. 1002 ¶¶ 2–6, 22–26). Patent Owner states that it submitted the following proposal for a POSITA in the related district court litigation: “[a POSITA] would have had at least a B.S. degree in Mechanical Engineering, Electrical Engineering, Aerospace Engineering, Industrial Design, Product Design, or similar field, with at least two years industry experience in one of these fields, and such POSITA would have been familiar with general principles of mechanics, fluid mechanics and aerodynamics.” PO Resp. 4–5. We note that the parties’ proposals overlap considerably, and neither party argues the inadequacy of the other party’s proposal or that any patentability issue in this case turns on the resolution of this issue. We find Petitioner’s definition consistent with the problems and solutions disclosed in the ’774 patent and prior art of record, and adopt it as our own. See, e.g., GPAC, 57 F.3d at 1579 (approving the determination of the level of ordinary skill in the art by appeal to the references of record). We would arrive at the same findings and conclusions in this Decision if we adopted Patent Owner’s proposal.” slip op. at 7

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Id. at 1312–13. Only terms in controversy need be construed, and only to the extent necessary to resolve the controversy. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). Petitioner contends that no “term requires construction to resolve the invalidity grounds presented in this Petition since the prior art renders claims 1–4, 12, and 15–17 unpatentable under any reasonable interpretation of the claims.” Pet. 7. Patent Owner argues that it “does not believe express claim constructions are necessary during this proceeding because the claims can readily be given their ordinary and customary meaning in the context of the patent at the time it was filed.” PO Resp. 5. Based on the parties’ positions and our view of the record, we need not expressly construe any claim limitations to resolve the issues in this Decision. To the extent that any implicit claim construction issues relate to the issues raised by the parties, we address them in the context of the parties’ patentability arguments below.” slip op. at 9

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentableUnpatentable

    “string, and that adding Scorch’s slot removes this arguably inconvenient process by allowing insertion and removal of a string without removing and reinstalling any aspects of the housing. See Pet 85–86 (citing Ex. 1002 ¶¶ 174–175; Ex. 1007, 3:30–3:53, 6:03; Ex. 1008, 3:46–4:45); Pet. Reply 18–20 (citing in part Ex. 2002 ¶ 187 (Dr. Janét’s testimony that Wagner’s removal and reinstallation of a cover “may be viewed as an inconvenient process”)). Making insertion and removal of the string easier and quicker provides a notable advantage over Wagner’s existing device. See id. Scorch itself supports this argument and the related expert testimony because it discusses insertion and removal of strings and stated that the slot allows a user to “swap them out really quick.” Ex. 1007, 3:30–53. Petitioner also persuasively argues that a POSITA would know how to add the slot while maintaining the proper operation of the device, such as allowing insertion and removal of the string and avoiding inadvertent exiting of the string from the device. See Pet. 86–87 (citing Ex. 1002 ¶¶ 175–176; Ex. 1007, 4:00–30, Ex. 1008, 2:49–52); Pet. Reply 19, 21 (citing Ex. 1002 ¶¶ 174–176). We find Petitioner’s arguments and reasoning in support of adding Scorch’s slot to Wagner’s housing straightforward and persuasive. Patent Owner’s arguments against the combination do not directly refute Petitioner’s reasoning or cast doubt on Scorch’s statement that its slot enables “quick” insertion and removal of a string—quicker than Wagner’s method that requires removal and replacement of a cover on its housing. See PO Resp. 16–22; PO Sur-reply 14–20; Ex. 2002 ¶ 187 (acknowledging inconvenience of Wagner’s existing process for insertion and removal of a string). Patent Owner suggests that Petitioner’s proposed combination fails to take into consideration certain drawbacks such as the risk of inadvertent string exit from the housing or slot, but Petitioner expressly addresses such concerns in the Petition. See PO Resp. 18 (stating that Scorch’s slotted funnel may allow the string to “shoot out the slot” and that Scorch addresses this by adding “a bent wire” to “prevent the string from coming out the side”); PO Sur-reply 16–17; Pet. 86–87 (arguing that Wagner’s flanges would help to trap the string in place, but if not, Scorch’s additional structures could be used to restring the string and “to further reduce the risk of a string inadvertently exiting” the device). We agree with Petitioner that a POSITA would understand how to incorporate Scorch’s slot without causing inadvertent removal of the string—using structures already present in Wagner and Scorch—and the need to add such unclaimed structurers does not teach away from the combination as Patent Owner suggests. See Pet. 86–87; PO Resp. 22. We also agree with Petitioner that a POSITA would understand how to make minor modifications, if necessary, to allow insertion and removal of the string around Wagner’s flanges. See Pet. Reply 21 (citing Ex. 1002 ¶¶ 174–176).” slip op. at 26

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner

    “refute Petitioner’s reasoning or cast doubt on Scorch’s statement that its slot enables “quick” insertion and removal of a string—quicker than Wagner’s method that requires removal and replacement of a cover on its housing. See PO Resp. 16–22; PO Sur-reply 14–20; Ex. 2002 ¶ 187 (acknowledging inconvenience of Wagner’s existing process for insertion and removal of a string). Patent Owner suggests that Petitioner’s proposed combination fails to take into consideration certain drawbacks such as the risk of inadvertent string exit from the housing or slot, but Petitioner expressly addresses such concerns in the Petition. See PO Resp. 18 (stating that Scorch’s slotted funnel may allow the string to “shoot out the slot” and that Scorch addresses this by adding “a bent wire” to “prevent the string from coming out the side”); PO Sur-reply 16–17; Pet. 86–87 (arguing that Wagner’s flanges would help to trap the string in place, but if not, Scorch’s additional structures could be used to restring the string and “to further reduce the risk of a string inadvertently exiting” the device). We agree with Petitioner that a POSITA would understand how to incorporate Scorch’s slot without causing inadvertent removal of the string—using structures already present in Wagner and Scorch—and the need to add such unclaimed structurers does not teach away from the combination as Patent Owner suggests. See Pet. 86–87; PO Resp. 22. We also agree with Petitioner that a POSITA would understand how to make minor modifications, if necessary, to allow insertion and removal of the string around Wagner’s flanges. See Pet. Reply 21 (citing Ex. 1002 ¶¶ 174–176). At best, Patent Owner’s arguments on this issue establish potential drawbacks in Petitioner’s proposed combination, but drawbacks alone do not defeat Petitioner’s obviousness rationale that includes readily apparent benefits. See Winner Int’l Royalty Corp. v. Wang, 202 F.3d 1340, 1349 n.8 (Fed. Cir. 2000) (“The fact that the motivating benefit comes at the expense of another benefit . . . should not nullify its use as a basis to modify the disclosure of one reference with the teachings of another.”); Medichem, S.A. v. Rolabo, S.L., 437 F.3d 1157, 1165 (Fed. Cir. 2006) (“a given course of action often has simultaneous advantages and disadvantages, and this does not necessarily obviate motivation to combine “). In addition, even if Patent Owner were correct that Wagner’s existing design works as well as Petitioner’s proposed combination, given all of the tradeoffs involved, that would not fatally undermine Petitioner’s showing. In re Fulton, 391 F.3d 1195, 1200 (Fed. Cir. 2004) (obviousness does not require that the proposed combination “is the preferred, or most desirable, combination”). On this record, Petitioner’s (and Scorch’s) stated advantages that are achieved when adding Scorch’s slot to Wagner’s housing adequately support Petitioner’s motivation to combine rationale.” slip op. at 26

  Patent outcomesUS 11,674,774 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · KSR · Nautilus
  Patents in suitUS 11,674,774
• Boe Technology Group Co., Ltd. v. Optronic Sciences LLCAll claims unpatentable
  PTAB · Feb 17, 2026 · IPR2024-01132 · APJ Kevin W Cherry · IPR · Final written decision

  Claims 1–7 are unpatentable: claims 1–3 and 5 are anticipated by Anzai, claim 4 is obvious over Anzai and Yamazaki, and claims 1–7 are obvious over Yamazaki and Anzai.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner describes a person of ordinary skill in the art (“POSITA” or “ordinarily skilled artisan”) at the time of the invention as having “a Bachelors’ degree in electrical engineering or a comparable field of study, plus approximately two to three years of professional experience with electronic and optoelectronic device design” and notes that “[a]dditional graduate education could substitute for professional experience, and significant experience in the field could substitute for formal education.” Pet. 5–6 (citing Ex. 1002, Neikirk Decl., ¶ 23). Patent Owner’s expert, Dr. Bretschneider testifies that In my opinion, the field of “electronic and optoelectronic device design” is too broad. A POSITA of the ’121, had at least a Bachelors’ degree in a field of engineering or physics and at least two to three years of professional experience related to the design and manufacture of the relevant aspects of flat panel displays. Additional relevant graduate education related [sic] could reduce but not eliminate the time requirement for professional experience. While Dr. Neikirk proposes a different definition of a POSITA, the differences do not have material effect on my opinions rendered below. Regardless of which definition of a POSITA were used, my conclusions would remain the same Ex. 2005, Bretschneider Decl., ¶ 39. We agree with and will apply Petitioner’s statement of the level of ordinary skill in the art. This level of ordinary skill is reflective of the education and experience that would have been required to understand the problems and solutions identified in the ’121 patent and the prior art. Okajima v. Bourdeau, 261 F.3d 1350 (Fed. Cir. 2001). We note that our conclusions would be the same even if we applied Patent Owner’s slightly narrower definition of a POSITA.” slip op. at 11

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “We find these definitions to be of some help in construing this term. We find that the common thread is that a “passivation layer” is an insulating layer that provides protection from the environment to the layers below it. See Ex. 1012, 140; Ex. 1013, 542, Ex. 1014, 798; Ex. 2010, 3; Ex. 2013, 1. We find this construction to be most consistent with the broad claim language and the disclosure in the Specification. Although “tying up dangling bonds,” may be a mechanism by which some materials provide such protection, nothing in the Specification or the extrinsic evidence provided appears to require that. Also, while chemical protection may be one kind of protection none of the evidence suggests that is the only protection that is provided. Moreover, nothing in the Specification supports reading a chemical protection requirement into the construction. Thus, we decline to adopt that portion of Patent Owner’s construction. Instead, we construe passivation layer as “an insulating layer that provides protection from the environment to the layers below it.” We need not construe the term any further to resolve the parties’ dispute over this claim language. See Realtime, 912 F.3d at 1375.” slip op. at 19

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

    “constructions for “passivation layer” and “capping layer.” We find that Petitioner has presented sufficient evidence to show that Anzai discloses both a “passivation layer” and a “capping layer.” As we explained above, we have construed “passivation layer” to mean “an insulating layer that provides protection from the environment to the layers below it.” Petitioner has shown that “first planarization film 17” is an insulating layer. See Ex. 1002 ¶¶ 62–65. We further find that Petitioner has shown sufficiently that “first planarization film 17” is “formed over the entire surface for flattening, which will protect the semiconductor surface from the surrounding environment.” Id. ¶ 63. We have rejected Patent Owner’s contentions that the film must tie up “dangling bonds,” and instead determined that protecting the surface from the environment is sufficient. Thus, we find that Petitioner has shown by a preponderance of the evidence that Anzai discloses the “passivation layer” of claim 3. As we explained above, we have construed “capping layer” to be “an insulation layer covering (i.e., capping) an underlying layer or structure.” Here, Petitioner has shown that Anzai’s planarization film 19 meets the claimed “capping layer.” See Pet. 20. We find that Petitioner has shown that it is more likely than not that “planarization film 19” is made of insulating material. As Dr. Neikirk persuasively testifies, Anzai discloses that planarization layer 17 may be made of an organic resin for flattening the surface. EX1003, 4:20-24. While Anzai does not disclose the material for planarization layer 19, it must be made of an insulation material because in the embodiment of Fig. 3A, it is the sole layer between electrode layer 71 and cathode layer 65 forming the second capacitor. Id., 6:3–8; Fig. 3A. Moreover, Anzai discloses that the first planarization film 17 and the second planarization film 19 for the first embodiment “function as the capacitance insulating film for this configuration.” Id., 5:62–67. Ex. 1002, Neikirk Decl., ¶ 62. We find this testimony well-reasoned and entitled to substantial weight. We further agree with Dr. Neikirk that a “POSITA would further understand that the second planarization film 19 is then further disposed on the first planarization film 17 (capping the passivation layer).” Id. ¶ 63 (citing Ex. 1003, 5:3–13; Figs. 2A–B, 3A–B). Thus, we find that Petitioner has shown by a preponderance of the evidence that Anzai discloses the claimed “capping layer.” Accordingly, we find that Petitioner has shown by a preponderance of” slip op. at 32

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “motivation to combine Anzai and Yamazaki. See Pet. 25–27; Ex. 1002, Neikirk Decl., ¶¶ 78–79. First, Patent Owner argues that essentially silicon nitride is an inferior material to use for Anzai’s planarization layer 17 compared with organic resin. PO Resp. 13–15. However, “[i]t’s not necessary to show that a combination is the best option, only that it be a suitable option.” Intel Corp. v. Qualcomm Inc., 21 F.4th 797, 800 (Fed. Cir. 2021) (emphasis in original). Patent Owner does not argue that silicon nitride would not work, but rather that it would be more difficult and more expensive to use. See PO Resp. 14. But “the fact that the two disclosed apparatus[es] would not be combined by businessmen for economic reasons is not the same as saying that it could not be done because skilled persons in the art felt that there was some technological incompatibility that prevented their combination. Only the latter is telling on the issue of nonobviousness.” Grit Energy Solutions LLC v. Oren Techs., LLC, 957 F.3d 1309, 1323 (Fed. Cir. 2020) (quoting Orthopedic Equip. Co., Inc. v. United States, 702 F.2d 1005, 1013 (Fed. Cir. 1983)). “Likewise, a given course of action often has simultaneous advantages and disadvantages, and this does not necessarily obviate motivation to combine.” Medichem, S.A. v. Rolabo, S.L., 437 F.3d 1157, 1165 (Fed. Cir. 2006). Here, Petitioner explains that “a POSITA would have known that organic materials usually have lower dielectric constants than inorganic materials, such as SiN, and a higher dielectric constant is desirable for the insulator in a capacitor since that leads to higher capacitance per unit area.” Pet. 26 (citing Ex. 1002, Neikirk Decl., ¶ 78). Petitioner further explains that this “then allows a reduced area storage capacitance element, one of the objectives of Anzai.” Id. (citing Ex. 1003, code (57)). Patent Owner’s focus mainly on planarization (PO Sur-reply 16–17) ignores that the Anzai’s planarization layers 17 and 19 also “function as the capacitance insulating film.” Ex. 1003, 5:65–67. Thus, although there are tradeoffs, Petitioner has shown sufficiently that a POSITA would have been motivated to incorporate the teachings of Yamazaki regarding potential materials for planarization layers 17 and 19. Second, Patent Owner argues that a Petitioner has failed to provide an adequate reason to select silicon nitride from Yamazaki’s list of potential materials. We disagree. Petitioner has explained the benefits of selecting a high dielectric inorganic material. Pet. 26. Yamazaki provides only three potential options—silicon oxide, silicon nitride, and silicon oxynitride. See Ex. 1004, 11:45–50. Moreover, Dr. Neikirk testified, supported by multiple references, that using silicon nitride was well known in the prior art at the time of the invention. See Ex. 1002, Neikirk Decl., ¶ 75 (citing Ex. 1007; Ex. 1008; Ex. 1009). “When there is a design need or market pressure to solve a problem and there are a finite number of identified, predictable solutions, a person of ordinary skill has good reason to pursue the known options within his or her technical grasp.” KSR, 550 U.S. at 421. Indeed, “[i]f a person of ordinary skill can implement a predictable variation, § 103 likely bars its patentability.” Id. at 417. This is the case here. Petitioner has shown that a person of ordinary skill seeking to improve the capacitance of Anzai’s planarization layers 17 and 19, without increasing the size of the capacitor, would have looked at the inorganic materials identified in Yamazaki as suitable for the purpose, and it would have been would obvious to choose silicon nitride, a well-known, and predictable material for the application. Thus, we disagree with Patent Owner that Petitioner has failed to show a sufficient reason for selecting silicon nitride from Yamazaki’s list of suitable materials. Third, Patent Owner argues that Petitioner’s contentions only support” slip op. at 37

  Patent outcomesUS 7,586,121 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 7,586,121
• 3d Diagnostix, Inc. v. Watson Guide IP, LLCAll claims unpatentable
  PTAB · Jan 27, 2026 · PGR2024-00040 · APJ James A Tartal · PGR · Final written decision

  Claims 1–3, 5–7, 10, 12, 14, 16, and 17 are unpatentable under § 103, including over Llop ’126 and Sichuan, and over Llop ’126, Sichuan, and Scherer for claims 5, 6, and 12.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for patent owner

    “B. Level of Ordinary Skill in the Art Petitioner contends that a person of ordinary skill in the art as of the earliest priority date of the ’209 patent “would at least have had a doctoral degree in dentistry and at least three to four years of experience working with guided dental surgery for installing dental implants and prostheses.” Pet. 13 (citing Ex. 1003 ¶ 49). Patent Owner agrees with Petitioner’s proposed definition of a person of ordinary skill in the art. Resp. 4. Based on our review of the record before us, we adopt Petitioner’s uncontested definition of a person of ordinary skill in the art, because it is supported by the evidence of record and consistent with the disclosure in the ’209 patent and in the asserted prior art.” slip op. at 11

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “1. “drill guide” and “fixation base” Petitioner contends that the claim terms “drill guide” and “fixation base” require construction “to resolve certain of the unpatentability grounds presented.” Pet. 13–14. In particular, Petitioner proposes that “drill guide” means “drill guide made from metal or metallic alloy without traditional plastic or acrylic,” and that “fixation base” means “fixation base made from metal, metallic alloy or other strong material without traditional plastic or acrylic.” Id. According to Petitioner, the Specification “teaches that the composition of the drill guide is ‘a metal or metallic alloy,’” and provides no other alternatives. Id. at 14 (citing Ex. 1001, 5:35–36). Petitioner similarly alleges that “fixation base” is described as “being fabricated from a metal, metal alloy, or other strong material,” and that “traditional plastic or acrylic” is excluded in light of disclosures in a provisional application. Id. at 21–24. According to Petitioner, its proposed constructions should be adopted “based on disclaimer of claim scope in the provisional application incorporated into the [’209] patent specification.” Id. at 14–24. Patent Owner contends that we need not address the constructions proposed by Petitioner because the issues addressed by Petitioner’s proposed constructions only concern allegations of unpatentability directed to claims 11 and 13, which Patent Owner disclaimed. Resp. 4–5; Disclaimer 1. In Reply, Petitioner argues that its proposed constructions are relevant to Patent Owner’s evidence of objective indicia of non-obviousness, including the alleged nexus. Reply 18–19 n.3. In light of our analysis below, because no determination in this Decision turns on whether we adopt Petitioner’s proposed constructions of “drill guide” and “fixation base,” we find that no express construction of these terms is required. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 12

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for petitioner

    “substitution of the word ‘enclose’ for the term ‘surround.’” Sur-reply 6. We noted in the Institution Decision that “construing the claim term ‘surround’ to mean ‘enclose’ does not further inform or clarify to a person of ordinary skill in the art what is encompassed by the claim limitation.” Dec. 15. We reach the same conclusion here on the full record and find no basis to rewrite the Challenged Claims to replace “surround” with “enclose.” To the extent Patent Owner can be understood to suggest that we import additional limitations into the claims based on the exemplary figures in the ’209 patent, we decline to do so. Regardless, given the recognition by the Parties that “surround” and “enclose” are synonymous, our determinations in this Decision would have been the same had we adopted Patent Owner’s proposed definition of “surround” to mean “enclose.” Further, with regard to the claim language “configured and dimensioned to surround at least a portion of the teeth of the patient,” Patent Owner proposes construing “a portion of the teeth” as “at least some teeth.” Resp. 9 (citing Ex. 2007 ¶ 44). Patent Owner, however, offers no sufficient explanation in its Response to explain how why a “portion of the teeth” means “at least some teeth.” The Specification does not provide an explicit definition of “a portion of the teeth” and does not suggest an intention to use a meaning of the term “a portion of the teeth” that is particular to the ’209 patent. To the extent Patent Owner can be understood to imply that we should import additional limitations into the Challenged Claims based on the exemplary figures in the ’209 patent, we decline to do so. For that reason, alone, we decline to adopt Patent Owner’s proposed construction.” slip op. at 17

  • Obviousness (§103) › Analogous artAnalogous artDecided for petitioner

    “38; Sur-reply 9–10. First, Patent Owner argues that Sichuan is non-analogous art. Resp. 34–38. “To be considered within the prior art for purposes of the obviousness analysis, a reference must be analogous.” Circuit Check Inc. v. QXQ Inc., 795 F.3d 1331, 1335 (Fed. Cir. 2015) (citing Wang Labs., Inc. v. Toshiba Corp., 993 F.2d 858, 864 (Fed. Cir. 1993)). “Two separate tests define the scope of analogous prior art: (1) whether the art is from the same field of endeavor, regardless of the problem addressed and, (2) if the reference is not within the field of the inventor’s endeavor, whether the reference still is reasonably pertinent to the particular problem with which the inventor is involved.” Sanofi-Aventis Deutschland GmbH v. Mylan Pharms. Inc., 66 F.4th 1373, 1377 (Fed. Cir. 2023) (quoting In re Bigio, 381 F.3d 1320, 1325 (Fed. Cir. 2004)).” slip op. at 36

  Patent outcomesUS 11,806,209 unpatentable
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,806,209
• Boe Technology Group Co., Ltd. v. Optronic Sciences, LLCAll claims unpatentable
  PTAB · Jan 26, 2026 · IPR2024-01133 · APJ Thu A Dang · IPR · Final written decision

  Claims 1–13 are unpatentable: claims 1–5, 9, and 12–13 as anticipated by Weaver, and claims 6–8 and 10–11 as obvious over the stated combinations.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “prior art of record. See Okajima v. Bourdeau, 261 F.3d 1350, 1354–55 (Fed. Cir. 2001) (holding that absent evidence to the contrary, “the prior art itself [may] reflect[] an appropriate level” of ordinary skill in the art). In general, we agree with the areas of agreement in the parties’ proposals. In particular, Patent Owner proposes “at least a Bachelors’ degree in a field of engineering or physics,” which includes “electrical engineering or a comparable field of study” as Petitioner proposes. Pet. 4 (emphasis added); PO Resp. 10. We agree with Petitioner that by defining the engineering field as “electrical” or “comparable,” we can exclude engineering fields “having nothing to do with displays, such as biomedical, civil, chemical or environmental engineering.” Pet. Reply 1. Petitioner also proposes approximately “one or more years of professional experience” which includes Patent Owner’s “at least two years of professional experience.” Pet. 4; PO Resp. 10. Furthermore, both parties agree that “[a]dditional graduate education could [reduce . . . the time requirement] for professional experience.” Id. Thus, we adopt both parties’ proposed POSITA of having a Bachelors’ degree in electrical engineering or a comparable field of study, plus at least two years of professional experience, wherein additional graduate education could reduce the time requirement for professional experience. Id. Such proposal comports with the level of ordinary skill in the art reflected in the prior art of record.” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed board ownOther

    “The plain language in claim 1 of “auxiliary electrode” does not preclude that the “electrode” may be a power line, bus line, or resistor. Ex. 1001, 8:47–52. Nothing in the Specification clearly precludes “auxiliary electrode” from being a “bus line” or “power line,” as Patent Owner proposes. PO Resp. 25–27. We are unpersuaded by Patent Owner’s contention that the Specification discloses that “the power line ‘PL’ is shown in Figure 1, but the power line PL is not an electrode that is shown in Figure 2.” Id. at 26–27. Here, Patent Owner points to no portions in the Specification that provide the requisite “reasonable clarity, deliberateness, and precision” to warrant interpreting the claim language at issue as supporting Patent Owner’s contention that an auxiliary electrode cannot be a power line, bus line, or resistor. Id.; In re Paulsen, 30 F.3d 1475, 1480 (Fed. Cir. 1984). That is, although Patent Owner points to Figures 1 and 2 of the Specification for support of its contention, Figures 1 and 2 of the Specification merely show various examples of power line and an auxiliary electrode. PO Resp. 26–27. Thus, although the referenced portions of the Specification discuss various examples wherein an auxiliary electrode may be implemented, nothing in these referenced portions of the Specification clearly precludes the “auxiliary electrode” from being a power line or any electrode that is “the road to get to an end point,” as Patent Owner contends. Id. Patent Owner points to no special definition, implicit or explicit, for “auxiliary electrode” that is set forth in the Specification which supports Patent Owner’s construction with reasonable clarity, deliberateness, and precision. Paulsen, 30 F.3d at 1480.” slip op. at 15

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

    “We find Patent Owner’s arguments unavailing. In particular, we find unavailing Patent Owner’s contention that “‘bus line 430’ is not an ‘auxiliary electrode’” (PO Resp. 28–33), because Patent Owner is relying on a claim construction of “auxiliary electrode” as precluding “essential” elements and requiring “more than the end structure of a conductor” (id.), that is not adopted by our construction discussed above. Here, we are persuaded by Petitioner’s reliance on Weaver’s bus line 430 for providing the claimed “electrode,” that is “supplemental to other electrodes in the structure.” Pet. 18; see also Ex. 1004 ¶ 26, Fig. 4; Ex. 1003 ¶ 92. We find availing Petitioner’s contention, supported by Dr. Baker’s testimony, that a POSITA would have understood that “anode 406 and bus line 430 are connected in parallel,” which means that “bus line 430 is a supplemental electrode that reduces the total resistance of the pixel structure.” Pet. 19; Ex. 1003 ¶ 94. Thus, we find availing Petitioner’s contention, supported by Dr. Baker’s testimony, that Weaver’s bus line 430 is an electrode supplemental to other electrodes in the structure that is electrically insulated from transistor 410 by passivation layer 409, wherein OLED 400, which includes cathode 422, organic layer 424, and anode 406, is disposed above bus line 430, and wherein anode 406 of OLED 400 is electrically connected to bus line 430 by via 428. Pet. 16–19; Ex. 1003 ¶¶ 89–94. That is, we find availing Petitioner’s contention that, like the ’509 patent’s auxiliary electrode 120, bus line 430 is electrically insulated from transistor 410, wherein OLED 400 is disposed above bus line 430 and anode 406 electrically connected with bus line 430. Compare Pet. 2–3 (annotated” slip op. at 26

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “We also find unavailing Patent Owner’s contention that the proposed modifications to Weaver would involve changing the process. PO Resp. 33– 34. We agree with Petitioner, whose contentions are supported by Dr. Baker’s testimony, that “to provide additional components from the same layer is a layout change that a POSITA would have been able to perform without changing the process.” Pet. Reply 17–18 (citing Ex 1003 ¶ 157; Ex. 1020 ¶ 45). Further, contrary to Patent Owner’s contention that POSITA would not have combined Weaver with Lee ’053, Song, Lee ’149, or Bae without the use of hindsight (PO Resp. 33–45), as Petitioner points out, Lee ’149, for example, “explicitly teaches that ‘the electrode pattern 45 serves to lower the resistance of the first electrode 41.” Pet. Reply 58 (citing Ex. 1011 ¶ 38). Similarly, Bae “explicitly teaches that the “auxiliary electrodes 139 contact the first electrode 132 to commonly apply a voltage to the sub-pixels” and “reduces the resistance of the first electrode.” Id. at 66 (citing Ex. 1012 ¶¶ 37, 59). As such, Petitioner’s proposed combinations are supported by at least by Lee ’149’s and Bae’s teachings of applying a second electrode to lower the resistance and voltage drop between anode 406 and the VDD line of Weaver. See, e.g., Ex. 1011 ¶ 38; Ex. 1012 ¶¶ 37, 59. We are persuaded by Dr. Baker’s testimony that a POSITA would have understood that higher resistance between the power or ground line to the light emitting device would consume more power and require higher operating voltages, and thus, would have been motivated to implement the solutions of Lee ’053, Song, Lee ’149, or Bae to lower the resistance between anode 406 and voltage source VDD in Weaver. Ex. 1003 ¶¶ 145, 158, 184, 203. We agree with Petitioner, supported by Dr. Baker’s testimony, that a POSITA would have had a reasonable expectation of success the combining the references as suggested, wherein such modification “involves modifications of only routine skill in the art,” which “involve known method,” and “would have yielded predictable results. Pet. 42, 48–49, 59, 67–68; Ex. 1003 ¶¶ 145, 158, 184, 203. That is, we determine that Petitioner has set forth reasoning with rational underpinning explaining why it would have been obvious to combine the teachings with a reasonable expectation of success. Based on the complete record presented, we determine Petitioner has shown by a preponderance of the evidence that claims 6–8 would have been obvious over the combination of Weaver and Lee ’053 or alternatively over the combination of Weaver and Song, and that claims 10 and 11 would have been obvious over the combination of Weaver and Lee ’149 or alternatively over the combination of Weaver and Bae.” slip op. at 33

  Patent outcomesUS 9,263,509 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,263,509
• Samsung Electronics Co., Ltd. / Samsung Electronics America, Inc. v. Ouraring, Inc.All claims unpatentable
  PTAB · Dec 2, 2025 · IPR2024-00928 · APJ Neil T Powell · IPR · Final written decision

  Claims 1–5, 11–13, and 16–18 are unpatentable as obvious over Schröder and Yuen, LeBoeuf, or LeBoeuf and Wissmar; Schröder alone did not render its challenged claims unpatentable.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedOther

    “Patent Owner agrees with Petitioner’s proposed definition of a person of ordinary skill in the art. PO Resp. 14. We adopt this uncontested definition of the level of ordinary skill in the art. This definition is supported by the record and consistent with the disclosure in the ’034 patent and the references cited in the Petition.” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “Petitioner has the better position, as we agree with Petitioner that the ’034 patent discloses an embodiment that uses transparent potting as a window, rather than to form the overall form factor and encapsulate components: [Figure] 16C is a perspective view of the WCD with potting material 1630. As described above, the PCB, battery, and components can be disposed within the space. Once disposed therein, a potting 1630 can be provided atop the components and within the cutaway portion 1616. The potting 1630 can be transparent to allow for transmission of light through the cutaway portions 1616. Ex. 1001, 20:51–57. This configuration is shown below in Figure 16C. “[Figure] 16C is a perspective view of the WCD with potting material.” Ex. 1001, 6:1–2. As Figure 16C shows, potting material 1616 forms a window in only a portion of the WCD’s exterior. can be used to encapsulate components and form the overall form factor in some embodiments. E.g., Ex. 1001, 17:4–8, 18:61–62. But Patent Owner does not persuade us that claim 12 is limited to those embodiments. PO Resp. 29; SuperGuide Corp. v. DirecTV Enters., Inc., 358 F.3d 870, 875 (Fed. Cir. 2004) (“Though understanding the claim language may be aided by the explanations contained in the written description, it is important not to import into a claim limitations that are not part of the claim.”). Accordingly, we do not construe claim 12’s “external transparent potting” as requiring material that “forms the ‘overall form factor of the WCD 120, in addition to providing a housing for one or more electronic components,’” as suggested by Patent Owner. PO Resp. 29. Nor do we construe the claim language as requiring material that “also fills the space and encapsulates the components,” as suggested by Patent Owner. Id.” slip op. at 11

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable

    “We are not persuaded by Petitioner’s arguments and find that Patent Owner has the better position. Although Schröder describes some aspects that are similar to those of a printed circuit board, Petitioner has not sufficiently demonstrated that a person having ordinary skill in the art would understand Schröder’s inlay 12 or carrier foil to be a “printed circuit board,” as recited in independent claims 1, 11, and 16. As an initial matter, while Schröder refers to a “circuit board” in another context, it never refers to the carrier foil or inlay in its finger-ring embodiment as such. See Ex. 1007, 22:48–49; see also Ex. 1079 ¶ 21 (Dr. Anthony acknowledging that Schröder’s only reference to a “circuit board” is “unrelated to Schröder’s finger-ring teachings”). Instead, Schröder describes features of that inlay, explaining that “[t]he carrier foil itself consists of a flexible plastic material, e.g.[,] PET or Kapton” and “antenna coil 8 can for example be printed on the carrier foil by means of a conductive paste” and “a depression is manufactured in the carrier foil, e.g.[,] by milling, lasering, etching, before the chip module 10, the antenna coil 8 and optional further electronic devices are inserted into the depression.” Ex. 1007, 13:26–31, 13:35–37. Schröder further describes that “[a]t least one further foil can be applied to the carrier foil or the ring blank on at least one side” to produce a “multilayer foil composite” that can be “interconnected” by means of “glue” slip op. at 23

  • Expert testimonyPetitioner expert discountedOther

    “show that Schröder’s inlay 12 is a PCB. Relying on testimony from Dr. Anthony, Petitioner asserts that Schröder’s inlay 12 serves as a flexible carrier made of materials “commonly understood to be printed circuit board materials” such as PET and Kapton. Pet. 23 (citing Ex. 1002 ¶ 172; Ex. 1006, 12:28–29). Dr. Anthony did not provide a clear explanation of a person of ordinary skill in the art’s understanding of a PCB in his direct testimony. article describing a PCB as a “laminated sandwich structure of conductive and insulating layers” was an accurate description of a PCB: Q. So is the first sentence of this Wiki page, in your mind, an accurate description of a printed circuit board? A. So, the first sentence, “A printed circuit board (PCB)[] also called [a] printed wiring board, []is a laminated sandwich structure of conductive and insulating layers, each with a pattern of traces, planes, and other features (similar to wires on a flat surface) etched from one or more sheets of copper laminated onto or between sheet layers of nonconductive substrate.” And so your question again was? Q. Is that a fair definition of printed circuit board in your mind? A. It’s a fair description of the general process for circuit boards, layers of conductive traces.” slip op. at 21

  Patent outcomesUS 9,582,034 unpatentable
  Claim construction§ 103 obviousness
  Patents in suitUS 9,582,034
• Samsung Electronics Co., Ltd. / Samsung Electronics America, Inc. et al. v. Eyesmatch Ltd.All claims unpatentable
  PTAB · Nov 21, 2025 · IPR2024-00810 · APJ Neil T Powell · IPR · Final written decision

  Claims 1–18 are unpatentable: claims 1–6 and 10–12 over Rosenberg and Park, and claims 3, 4, 7–9, and 11–18 over Rosenberg, Park, and Geisner.

  RulingsFinal written decision

  • Prior constructionPrior construction adoptedDecided for patent owner

    “Turning to the substantive issues, we find the District Court’s “mirror tracking mode” construction to be well-reasoned and supported by the record, and we therefore adopt that construction and its reasoning. As the District Court points out, both the “double the distance” and “same size” aspects of its construction are expressly discussed in the ’109 patent, which is incorporated in the ’110 patent. See Ex. 2008, 16 (citing Ex. 1021, 2:5–27, Figs. 5A, 5B), 40 (citing “same reasons set forth regarding the term ‘it appears to mimic a reflection of a mirror’” in support of construction of “mirror tracking mode”). So, too, is “flipping” or reversing of the image disclosed. Id. at 17 (citing Ex. 1021, 14:46–51, 15:41–47), 40.” slip op. at 14

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable

    “persuasively address limitation 1[f]’s “mirror tracking mode.” In particular, Petitioner does not address persuasively the requirement, as explained in Section II.B above, that mirror tracking mode involves processing camera-captured images in a way that “maintains roughly the same size regardless of the user movement.” At odds with this requirement, Petitioner founds its case on an assertion that “Haan teaches the claimed mirror tracking mode” because “if the viewer is within 35 cm of the camera, a tracking mode is entered, applying resizing transformation.” Pet. 44 (emphasis added) (citing Ex. 1005 ¶¶ 75–76, 80–82, 90–94, 97; Ex. 1003 ¶¶ 205–210). The resizing transformation Petitioner references actually involves magnifying the user’s image by an amount that changes based on the user’s position relative to the camera, quite the opposite of maintaining image size regardless of the user movement. Ex. 1005 ¶¶ 75–76, Fig. 8. Thus, Petitioner’s initial position is unpersuasive. Petitioner’s shift to Haan’s “reflective mirror mode and conventional mirror period in the dual mode” is also unavailing. Reply 8. Consistent with Patent Owner’s arguments, Petitioner does not provide persuasive evidence that these operating states of Haan’s device involve any processing of camera-captured images. Sur-reply 13–14. To the contrary, Haan suggests that anytime its device provides an unmagnified image, it comes from a reflection off a physical reflective surface. See, e.g., Ex.1005 ¶ 76 (“This can be done for instance by using the device as a simple mirror, i.e. not displaying an image on the display device, but using the device in the reflective mode.”) (emphasis added), ¶ 92 (“a simple reflective mode, to act as a mirror”), ¶ 29 (“for a first range of positions, no image is displayed, whereby the reflective layer acts as a mirror, and for a second range of positions, the recorded image is displayed.”) (emphasis added). We also find unpersuasive Petitioner’s Reply arguments based on Haan’s disclosure of smoothly transitioning from “using the device as a simple mirror” (i.e., using a physical reflecting surface) to displaying a magnified image. Reply 11 (citing Ex. 1005 ¶¶ 76, 80). To the extent this may establish a point around the transition at which Haan’s system displays an image with relatively little magnification, it does not establish that Haan teaches, suggests, or renders obvious holding the displayed size roughly constant, “regardless of the user movement.” Indeed, given Haan’s focus on helping the user see things more clearly with image magnification, Petitioner’s argument that it would have been obvious to hold the size of the image constant is not persuasive. See, e.g., Ex. 1005 ¶ 4. Thus, on the whole, Petitioner’s shifting, scattered arguments do not persuasively address limitation 1[f]. Accordingly, Petitioner has not shown by a preponderance of the evidence that claim 1 would have been obvious over Haan and Francois. And Petitioner’s arguments and evidence addressing claims 2–6, 10–12, 16, and 17 do not cure the foregoing deficiencies in the challenge of claim 1. Pet. 46–52. Accordingly, Petitioner has not shown by a preponderance of the evidence that any of claims 1–6, 10–12, 16, and 17 would have been obvious over Haan and Francois.” slip op. at 23

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner

    “We do not agree. Petitioner demonstrates persuasively that a person of ordinary skill would have combined these references “to correct image distortions and provide a more realistic mirror image.” Pet. 52–55; Ex. 1003 ¶¶ 242–249. We are not persuaded by Patent Owner that by specifically disclosing “flipping” the image, Rosenberg is discouraging or teaching away from performing other transformations to achieve its objective of “replicat[ing] the performance of a standard household mirror.” See PO Resp. 35, 38–39 (Patent Owner asserting lack of motivation to combine the references). A reference may be said to “teach away” “when a person of ordinary skill, upon reading the reference, would be discouraged from following the path set out in the reference, or would be led in a direction divergent from the path that was taken by the applicant.” Galderma Lab'ys, L.P. v. Tolmar, Inc., 737 F.3d 731, 738 (Fed. Cir. 2013) (quoting DePuy Spine, Inc. v. Medtronic Sofamor Danek, Inc., 567 F.3d 1314, 1327 (Fed.Cir.2009)). “A reference does not teach away, however, if it merely expresses a general preference for an alternative invention but does not criticize, discredit, or otherwise discourage investigation into the invention claimed.” Id. Further, when conducting an obviousness analysis, the Board must consider a prior art reference “not only for what it expressly teaches, but also for what it fairly suggests.” Bradium Techs. LLC v. Iancu, 923 F.3d 1032, 1049 (Fed. Cir. 2019) (quoting In re Baird, 16 F.3d 380, 383 (Fed. Cir. 1994)). We are not convinced that the references before us “teach away” from performing the other transformations. In sum, we find for the reasons given that Petitioner has demonstrated by a preponderance of evidence that to a person of ordinary skill, Rosenberg alone or with Park teaches or suggests limitation 1[f].” slip op. at 44

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable

    “shows by a preponderance of the evidence that limitations 1[c] and 1[e] are taught or suggested by Rosenberg and Park, in combination. Pet. 58–64; PO Resp. 39–40; Reply 19–20; Sur-reply 19. Petitioner persuades us that limitations 1[c] and 1[e], would have been obvious over Rosenberg and Park, in combination. Pet. 58–64; Reply 19–20. Patent Owner’s counter arguments are unavailing for multiple reasons. Patent Owner’s arguments fail because they improperly attack Rosenberg’s teachings individually, rather than addressing Petitioner’s combination of the references. PO Resp. 39–40; Sur-reply 19. This is fatal to Patent Owner’s arguments. In re Merck & Co., 800 F.2d 1091, 1097 (Fed. Cir. 1986). Moreover, Petitioner presents persuasive arguments and evidence that the references, in combination, teach limitations 1[c] and 1[e], including persuasive evidence that the references’ tilting, resizing, and zooming meet the claim limitations’ “adaptive transformation mapping . . . to generate modified images that appear to be captured from a different point of view” that “corresponds to an image taken from a different angle and a different distance.” Pet. 58–64 (citing Ex. 1001, 3:26–28; Ex. 1003 ¶¶ 65–67, 253–268; Ex. 1006 ¶¶ 26–28, 50, 52, 61, 75 ; Ex. 1011 ¶¶ 50–51, 59, Figs. 6A–6B, 7, 8, 14, 15; Ex. 1019, 16–20; Ex. 1021, 2:19–27, 17:19–24, 21:60, 23:65–24:9, 25:46–48, 30:4–11, Fig. 11); Reply 19–20 (citing Ex. 1003 ¶¶ 253–268; Ex. 1021, 17:17–23; Ex. 2012, 63:13–22, 111:13–21). Regarding tilting, after noting the ’110 patent’s disclosure (incorporated from the ’109 patent) of performing tilt transformations (Pet. 10–11), Petitioner advances persuasive evidence that Park discloses such a tilting transformation, thereby teaching the claimed “different angle” (id. at 61–63). Regarding resizing and zooming, citing extensive discussion in the ’110 patent (incorporated from the ’109 patent) of resizing and/or zooming to address the effects of varying distance between an object and a camera, Petitioner and Dr. Karam explain that the prior art’s zooming and resizing meet the claimed “different distance.” Pet. 63 (Ex. 1001, 3:26–28; Ex. 1021, 17:19–23, 21:57–60, 23:65–24:9, 25:46–48, 30:4–11, Fig. 11); Ex. 1003 ¶ 265 (citing Ex. 1001, 3:26–28; Ex. 1021, 17:19–23, 21:57–60, 23:65–24:9, 25:46–48, 30:4–11, Fig. 11). In its counterarguments, Patent Owner suggests that zooming and resizing do not account for “occlusion effects,” but Patent Owner does not persuasively tie this argument to the ’110 patent, failing to cite any portion of the ’110 patent that evinces its invention addresses such effects. PO Resp. 23–25, 39–40.” slip op. at 39

  Patent outcomesUS 8,982,110 unpatentable
  Claim construction§ 103 obviousnesscites Phillips
  Patents in suitUS 8,982,110

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.