• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00187 · APJ Debra L Dennett · IPR · Final written decision

  Claims 1–17 are unpatentable under § 103, principally because Chang in view of Jin renders them obvious; the Jin/Feldmann grounds were not shown.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49).” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11

  • Expert testimonyPatent owner expert creditedDecided for patent owner

    “gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard. Without an apparent reason to modify the teachings of Jin and Feldmann to” slip op. at 19

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 17

  Patent outcomesUS 10,230,009 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,230,009
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00006 · APJ Debra L Dennett · IPR · Final written decision

  Claims 1–17 are unpatentable under § 103, principally over Chang and Jin; the Board rejected the Jin and Feldmann combinations for lack of a reason to combine.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’009 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’009 patent and the prior art.” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 26. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 116 with Pet. 26). Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” See Magnum, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard.” slip op. at 19

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” Resp. 42 (citing Ex. 1013 ¶ 76). In so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Id. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Chang ¶ 62; Tr. 15:20–17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 73, 217 (citing Ex. 1023 § 1). Chang also discloses that the emitter area may be formed by thermal diffusion, ion implantation or the like. Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding a tunneling layer and a base surface field area from periphery region and isolation region. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” slip op. at 32

  Patent outcomesUS 10,230,009 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,230,009
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00918 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board rejected the Jin and Feldmann based grounds for lack of a reason to combine without hindsight.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “Patent Owner focuses on Chang’s description in paragraph 76 of a single configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” PO Resp. 42–43 (citing Ex. 1013 ¶ 76). But, in so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Ex. 1013 ¶ 62; Tr. 15:20– 17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 70–81, 91–96, 200 (citing Ex. 1026 § 1 and stating that “[b]oth Chang and Jin likewise teach backside isolation regions”). Chang also discloses that the emitter area may be formed by “thermal diffusion, ion implantation or the like.” Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Pet. Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding the second tunneling layer and a base surface field area from periphery region and isolation portion. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art “reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” Ex. 1003 ¶ 201.” slip op. at 33

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00186 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board found the combination disclosed the claimed isolation portion and supported the challenged claims.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “C. Claim Construction We construe claim terms according to the standard set forth in Phillips v. AWH Corp., 415 F.3d 1303, 1312–17 (Fed. Cir. 2005) (en banc); 37 C.F.R. § 42.100(b). Under Phillips, we give claim terms “their ordinary and customary meaning.” Phillips, 415 F.3d at 1312. “[T]he ordinary and customary meaning of a claim term is the meaning that the term would have to a person of ordinary skill in the art in question at the time of the invention.” Id. at 1313. “Importantly, the person of ordinary skill in the art is deemed to read the claim term not only in the context of the particular claim in which the disputed term appears, but in the context of the entire patent, including the specification.” Id. Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Expert testimonyPetitioner expert discountedPatent owner expert creditedMixed

    “edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001” slip op. at 18

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00007 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under §103 over Chang and Jin because the combination teaches the claimed isolation portion and the claimed tapering.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedOther

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightTeaching away not foundNot shown unpatentable

    “On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  • Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner

    “However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide.” slip op. at 18

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• Bio-Rad Laboratories, Inc. v. California Institute Of TechnologyNo claims unpatentable
  PTAB · Mar 23, 2026 · IPR2024-01451 · APJ Tawen Chang · IPR · Final written decision

  Claims 1–19 were not shown unpatentable: Larson did not establish the claimed detection in a single sample volume, and the asserted obviousness combinations did not cure the deficiencies.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Patent Owner states that, “[f]or purposes of this IPR proceeding, PO does not contest Petitioner’s description of qualifications for a person of ordinary skill in the art (POSA) set forth [above].” PO Resp. 23. In view of the above, and because Petitioner’s uncontested description of one of ordinary skill in the art is reasonable and consistent with the ’921 patent and the cited art, we adopt Petitioner’s definition of a POSA for purposes of this Decision, except that we replace the phrase “at least a year of experience in quantitative and/or dPCR and fluorescence-based analyte detection” with “around a year of experience in quantitative and/or dPCR and fluorescence-based analyte detection.” Pet. 9 (emphasis added).13” slip op. at 14

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

    “We begin with “the context in which a term is used in the asserted claim,” which can be “highly instructive.” Phillips, 415 F.3d at 1314. In this case, claim 1 recites that the claimed assay is “capable of unambiguously detecting the presence or absence of each of said at least M analytes, in any combination of presence or absence, in a single sample volume, . . . wherein the analytes are amplified in the single sample 15 In this regard, we note that Petitioner’s claim construction position is not predicated on the collection of droplets being reconstituted into its original, pre-partition form prior to amplification; rather, the droplets remain compartmentalized from each other in the PCR thermal cycling tube. Tr. 65:21–66:9 (Petitioner’s counsel explaining that the droplets do not combine in the PCR thermal cycling tube but, rather, are “suspended in an immiscible fluid and analyzed en masse”). indicates that the first instance of single sample volume, i.e., the single sample volume in which the presence or absence of each M analytes are to be detected, is the antecedent basis for the second instance of “single sample volume,” i.e., the single sample volume in which the analytes are amplified. Thus, as the parties appear to agree, the single sample volume in which amplification takes places must be the same single sample volume in which the presence or absence of analytes are to be detected. We are not persuaded that, when accorded its plain and ordinary meaning, a single sample volume divided into a collection of droplets would be considered the “same” single sample volume prior to its partition.” slip op. at 17

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

    “With respect to the limitation, “wherein the analytes are amplified in the single sample volume,” Petitioner asserts that “Larson discloses PCR assays that amplify target polynucleotide in a single sample volume, specifically a portion of the reaction mixture that is subsequently partitioned into droplets.” Pet. 31 (emphasis added). There is no dispute that the amplification of the analytes in Larson occurs in the droplets. Larson ¶¶ 6–7 (explaining that “[d]igital PCR (dPCR) is an alternative quantitation method in which dilute sample are divided into many separate reactions” and that “[t]he template is amplified in the droplet for detection”) (emphasis added). Because the claims require that amplification of the analytes be in the same sample volume in which the at least M analytes, in any combination of presence or absence, is unambiguously detected, and because the pre-partition single sample volume is not the same single sample volume as the collection of droplets after partition under our claim construction set forth above, we find Petitioner has not shown, by a preponderance of evidence, that claims 1–10 and 13–19 are anticipated by Larson.17 Tr. 68:12–69:14 (Petitioner’s counsel” slip op. at 27

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable

    “Although we agree with Petitioner that Larson contemplates scenarios in which droplets may contain more than one target molecule and does not require the exclusion of such multiple occupancy droplets in all embodiments, we are nevertheless not persuaded Petitioner has shown, based on a preponderance of evidence, that Larson renders obvious an assay capable of unambiguously detecting, in such multiple occupancy droplets, the presence or absence of each of at least M analytes, in any combination of presence or absence, when M is greater than F and F is at least 2.” slip op. at 32

  Patent outcomesUS 11,827,921 not shown unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 11,827,921
• Shenzhen Root Technology Co., Ltd. v. Willow Blossom Holdco LimitedAll claims unpatentable
  PTAB · Feb 18, 2026 · IPR2024-01296 · APJ Barry L Grossman · IPR · Final written decision

  Claims 1–46 are unpatentable as obvious under § 103 over the asserted combinations of Chang, Fang, Yuen, Khalil, Park, and Chen.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner asserts that before the effective filing date of the claimed invention a person of ordinary skill in the art (“POSITA”) “would have had at least a bachelor’s degree in mechanical engineering or a similar field and at least two years of experience designing human breast pump equipment” and that “[m]ore education could substitute for experience and vice versa.” Pet. 2 (citing Ex. 1003 ¶¶ 15–18). Mr. Bauer’s cited testimony supports Petitioner’s assertion.” slip op. at 16

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “[parent application to the application that matured into the ’380 patent], the Examiner construed the term ‘self-contained, in-bra wearable device’ to mean ‘complete, or having all that is needed, in itself’ and is capable of being worn in a bra.” Pet. 3 (citing Ex. 1005, 2290) (emphasis omitted). According to Petitioner, “PO did not dispute this construction, and Petitioner applies it herein.” Id. Petitioner also states that “[o]ther terms of the Challenged Claims should receive their plain and ordinary meaning, and no formal claim constructions are necessary in this proceeding because ‘claim terms need only be construed to the extent necessary to resolve the controversy.’” Id. (citing Wellman, Inc. v. Eastman Chem. Co., 642 F.3d 1355, 1361 (Fed. Cir. 2011); Ex. 1003 ¶¶ 69–70). Again, because Patent Owner did not file a Response, we exercise our discretion and look to Patent Owner’s Preliminary Response. We note that in the Preliminary Response Patent Owner states that “[f]or purposes of this Preliminary Response, no claim terms require construction to resolve the prior art grounds raised in the Petition.” Prelim. Resp. 19. According to specific construction, any such terms should be accorded their plain and ordinary meaning in light of the specification.” Id. Construction is needed only for those terms “that are in controversy, and only to the extent necessary to resolve the controversy.” See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). There are no claim terms in controversy. Accordingly, we need not construe any terms for our analysis.” slip op. at 17

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundUnpatentable

    “Petitioner contends (Pet. 17) that a person of ordinary skill in the art “would have been motivated to implement Chang’s breast pump device as suggested by Fang” to achieve four benefits: (1) “to facilitate convenient cleaning and maintenance” (Pet. 19 (citing Ex, 1003 ¶ 102)); (2) “to facilitate more rapid assembly and disassembly (e.g., during use)” (id. at 20–21 (citing Ex. 1003 ¶ 105)); (3) “as a particularly effective and suitable option to generate negative” slip op. at 34

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable

    “a breast pump device having “a diaphragm pump that generates negative air pressure.” Pet. 33; see also id. at 38. Petitioner explains Chang’s pump “generates suction by cyclical compression and decompression of a conduit or flex-tube, and expressly notes that other configurations were known and suitable.” Id. at 17 (citing Ex. 1007 ¶¶ 22, 25, 28, 68, 79, 84–86). Chang, however, does not mention, specifically, that Chang’s pump is a “diaphragm” pump. We note, however, that this claim clause does not state or require any specific type of pump. It merely requires a “pump.” Clause 1[e]/29[e], discussed below, however, does require a “diaphragm” pump. Petitioner here merely lays the foundation for this later clause by asserting that “Fang provides a straightforward suggestion of a diaphragm pump including a diaphragm housing component formed in a wall of the pump housing.” Id. at 18 (citing Ex. 1009 ¶¶ 24–25, Fig. 7; Ex. 1003 ¶ 97). Thus, Petitioner asserts, Fang teaches “an ‘air pump’ in pneumatic connection with the diaphragm that serves to generate negative air pressure,” and Chang teaches “the location of pump components (e.g., ‘motor’ [46]).” Pet. 33 (citing Ex. 1007 ¶¶ 72, 80, Fig, 6A; Ex. 1009 ¶¶ 19, 24). Petitioner then asserts that “the ‘air pump’ components of the combined device are positioned within the pump housing,” and the air pump is powered by Chang’s rechargeable battery. Id. (citing Ex. 1007 ¶¶ 72, 80).” slip op. at 34

  Patent outcomesUS 11,413,380 unpatentable
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,413,380
• Samsung Display Co., Ltd. v. Pictiva Displays International Ltd.All claims unpatentable
  PTAB · Jan 22, 2026 · IPR2024-01093 · APJ Grace Karaffa Obermann · IPR · Final written decision

  Claims 1–16 are unpatentable: claims 1–13 and 15–16 on anticipation and obviousness grounds, and claim 14 on obviousness over Choulis.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “A person of ordinary skill in the art (“POSITA”) at the time of the alleged invention of the ’164 patent would have had a Bachelor’s degree in chemistry, physics, or a comparable field of study, and at least three years of research or industrial experience with organic optoelectronic light-emitting devices. An individual with additional education could have less research or industrial experience and vice versa. Pet. 12. Patent Owner repeatedly refers to “a POSITA” without addressing the definition of that term or contesting Petitioner’s proposed definition. See Resp. 1, 2 n.1, 3, 8, 9, 15–21, 23, 26, 29, 32–33, 35, 37, 38, 40, 41, 44–49, 51–57, 61, 62 (bare references to “a POSITA”). Neither party indicates that the ultimate result on patentability would change depending on the definition selected. We adopt Petitioner’s proposed definition, which is not contested, because it is consistent with the disclosures of the asserted prior art. See Ex. 1004, (code 57); Ex. 1006, code (57); Ex. 1008, code (57); Ex. 1009, code (57) (abstracts of the references asserted in the patentability challenges).” slip op. at 7

  • Claim Construction › Intrinsic evidence (Phillips canons) › Specification disavowal / 'present invention' languageDisclaimer not foundTerm construed board ownDecided for petitioner

    “because no information raised during the trial phase of this review changes the calculus: First and foremost, the plain terms of claim 1 include no language from which we reasonably can impose limits on the phrase “matrix material” as urged by Patent Owner. In addition, the specification includes no special definition of that phrase that supports importing Patent Owner’s proposed narrowing limitation into the claim. Furthermore, we are directed to no disclaimer of claim scope during patent prosecution that would support Patent Owner’s twice-rejected argument that the phrase “matrix material” in claim 1 excludes embedded dopants and dispersed agglomerations. And the extrinsic evidence advanced by Patent Owner during this review is ineffective to override the clear interpretation of “matrix material” that is established by the intrinsic evidence. Reply 1–7.10” slip op. at 8

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableNot shown unpatentableMixed

    “We find that Petitioner establishes by a preponderance of the evidence that Choulis anticipates claim 13. We agree with Petitioner, in that regard, that Choulis explicitly teaches “using spin-coating as a method for depositing materials, which involves a simultaneous application process” as required by claim 13. Reply 16 (citing Pet. 40–41; Ex. 1044 ¶ 45).16 We 15 Petitioner raises Djobo as a background reference supporting that Choulis anticipates deposition of PVK by evaporation. Pet. 41. Patent Owner counters that Djobo, to the contrary, shows that Choulis does not teach deposition of PVK by evaporation. Resp. 48. In other words, both parties cite Djobo in connection with the ground based on anticipation by Choulis. Against that backdrop, we determine that Patent Owner waives any argument that Petitioner improperly cites Djobo as a background reference in support of the anticipation challenge, which is based on Choulis alone. Resp. 48 (nowhere asserting that the challenge is deficient on that basis). That waiver arises because no argument, in that regard, is raised in Patent Owner’s Response see Inst. Dec. 34 (“The Board shall deemed waived any issue not raised by Patent Owner in a timely response to the Petition . . . .”). 16 Patent Owner’s statement that “spin coating tends to cause phase separation” is not developed adequately on this record and, therefore, is further agree with Petitioner that Patent Owner “has not contested this point.” Resp. 48. “Therefore, there is no genuine dispute regarding the unpatentability of claim 13,” although Patent Owner raises “arguments concerning evaporation, which is a distinct process from spin-coating” relevant to the additional limitations of claim 14. Reply 16. We determine that Petitioner establishes by a preponderance of the evidence that Choulis anticipates claim 13. Patent Owner, however, has the better position on whether Choulis anticipates claim 14, which “includes the requirement of applying matrix materials via evaporation coating.” Reply 16. Petitioner seems to abandon that challenge in the Reply by raising arguments that appear, on this record, to bear exclusively on whether the subject matter of claim 14 would have been obvious over Choulis.17 Id. at 16–17. Those arguments are insufficient to counter Patent Owner’s reasons why Choulis does not anticipate the “evaporation coating” limitation of claim 14. Compare id., with Resp. 48. On this record, therefore, we determine that Petitioner does not establish by a preponderance of the evidence that Choulis anticipates claim 14. unpersuasive to persuade us “that Choulis does not have three matrix materials.” Sur-reply 15. That argument runs counter to Choulis’s explicit, intrinsic disclosures, which illustrate (Ex. 1004, Fig. 4) and describe (id. ¶ 30) an organic light emitting layer composed of three matrix materials. See Pet. 24–25 (citing Ex. 1004, Fig. 4, ¶ 30); see also Ex. 1003 ¶¶ 85–88 (persuasive declaration testimony of Dr. Holmes, cited at Pet. 24–25). 17 There is some confusion on this point, given that both parties sometimes collapse, into a single argument, whether Choulis anticipates or renders obvious claim 1. Compare Resp. 48, with Reply 16–17.” slip op. at 35

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “On this record, therefore, we determine that Choulis, at minimum, suggests that a person of ordinary skill in the art at the time of the invention would have recognized PMMA as a suitable alternative to PVK in Choulis’s Figure 4 embodiment, notwithstanding any differences raised by Patent Owner. Ex. 1004 ¶ 44. Patent Owner’s argument that no disclosure in Choulis suggests that an ordinarily skilled artisan “would have found it desirable to use PMMA in place of PVK in Choulis’s devices” misses the mark, where Choulis includes both PMMA and PVK in lists of materials suitable for use as host or matrix materials. Resp. 38; Ex. 1004 ¶ 44. “Our caselaw is clear. It’s not necessary to show that a combination is ‘the best option, only that it is a suitable option.’” Intel Corp. v. Qualcomm Inc., 21 F.4th 784, 800 (Fed. Cir. 2021). Even if Choulis does not expressly disclose substituting PMMA for PVK in the Figure 4 embodiment, “an ordinarily skilled artisan would have found it obvious to make that substitution.” Reply 10 (citing Pet. 31 (citing Ex. 1003 ¶ 100; Ex. 1044 ¶ 23)). The suggestion for that substitution is set forth unambiguously in Choulis’s listing of both “PVK” and “PMMA” as materials suitable for use as a first “host” material in Choulis’s organic functional layer; that is, “the light emitting layer” that is “described above” in Figure 4. Ex. 1004 ¶ 44. ii. Alternative Reasoning for Replacing PVK with PMMA Patent Owner counterargues that using PPMA in place of PVK would have been understood to “upset the hole and electron balance,” as well as “affect hole-charge recombination,” and “degrade the performance of the resulting OLED system.” Resp. 37. Petitioner responds with evidence that “it would have been a routine task for” an ordinarily skilled artisan “to optimize the composition of each component within the light-emitting layer to achieve the desired charge balance.” Reply 11 (citing Ex. 1004 ¶ 24). Petitioner’s response brings to light a second reason why an ordinarily” slip op. at 40

  Patent outcomesUS 8,723,164 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 8,723,164
• Advancell Pty Ltd. v. Sciencons As And Artbio, Inc.Instituted
  PTAB · Nov 6, 2025 · PGR2025-00040 · APJ Kimberly Mcgraw · PGR · Institution

  The Board instituted PGR on claims 1–9, 11–33, and 35–38 on all petition grounds, finding it more likely than not that Hassfjell-Hoff anticipates at least claim 1.

  RulingsInstitution decision

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted

    “Under 35 U.S.C. § 324(a), a post-grant review may be instituted only if “the information presented in the petition . . . demonstrate[s] that it is more likely than not that at least 1 of the claims challenged in the petition is unpatentable.” Post-grant review is available for patents that issue from applications that at one point contained at least one claim with an effective filing date on or after March 16, 2013. See Leahy-Smith America Invents Act, Pub. L. No. 112-29, 125 Stat. 284 (2011) (“AIA”), §§ 3(n)(1), 6(f)(2)(A). After considering the briefing and the evidence of record, for the reasons set forth below, we determine that Petitioner has shown that the ’437 patent is eligible for post-grant review and that it is more likely than not that at least one challenged claim of the ’437 patent is unpatentable under § 324(a). Accordingly, we institute a post-grant review of all challenged claims of the ’437 patent.” slip op. at 2

  • Adverse judgmentAdverse judgmentOther

    “Here, Patentee Sciencons AS filed a statutory disclaimer of claims 10 and 34 of the ’437 patent. Ex. 2001; Prelim. Resp. 43. Based on our review of Exhibit 2001 and the Office’s public records, we find that the disclaimer of claims 10 and 34 complies with the above-listed requirements of 37 C.F.R. § 1.321(a). Accordingly, we treat claims 10 and 34 as having never been part of the ’437 patent. See Vectra Fitness, Inc. v. TNWK Corp., 162 F.3d 1379, 1383 (Fed. Cir. 1998) (“This court has interpreted the term ‘considered as part of the original patent’ in [35 U.S.C.] § 253 to mean that the patent is treated as though the disclaimed claims never existed.”). Because post-grant review cannot be instituted based on disclaimed claims, claims 10 and 34 are outside the scope of this proceeding. 37 C.F.R. § 42.207(e) (“No post-grant review will be instituted based on disclaimed claims.”); General Elec. Co. v. United Techs. Corp., IPR2017-00491, Paper 9 (PTAB July 6, 2017) (precedential) (denying institution in view of a statutory disclaimer of all the challenged claims). Thus, we confine our analysis in this Decision to claims 1–9, 11–33, and 35– 38, the remaining challenged claims that have not been disclaimed.” slip op. at 6

  • PTAB / AIA Trials › Real party in interest / privityGranted

    “Sciencons AS also states that ARTBIO, Inc. is responsible for defending the ’437 patent in this proceeding and requests that ARTBIO, Inc. be included in the caption for this proceeding.2 Paper 4, 1. ARTBIO, Inc. has signed powers of attorney appointing the same practitioners that were appointed by Sciencons AS to transact all business associated with the instant post-grant review review of the ’437 patent. See Paper 3. To date, no objection has been raised to Patent Owner’s request. Given Sciencons AS’s representation that ARTBIO, Inc. is currently the exclusive licensee of the ’437 patent and is responsible for defending the ’437 patent, we grant Sciencons AS’s unopposed request that ARTBIO, Inc. be included in the caption. For convenience we refer to Sciencons AS and the purported exclusive licensee ARTBIO, Inc. collectively as “Patent Owner.” As stated supra, to the extent any party disputes ARTBIO, Inc.’s right to participate in this proceeding or to be included in the caption, the party shall request authorization to brief the issue within 10 business days of this Decision.” slip op. at 3

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “nuclear chemistry, radiochemistry, or materials science, or a comparable field of study, plus approximately two to three years of professional experience with radioisotope generators, radiopharmaceutical chemistry, nuclear medicine, or other relevant industry experience” and that “[a]dditional graduate education could substitute for professional experience, and significant experience in the field could substitute for formal education.” Pet. 2–3 (citing Ex. 1002 ¶ 33; Ex. 1019 ¶ 27). At this stage of the proceeding, Patent Owner does not dispute Petitioner’s proposed definition nor provide a proposed definition of its own. See generally Prelim. Resp. For the purposes of this Decision, we adopt Petitioner’s undisputed proposed definition of a POSITA.” slip op. at 10

  Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips
  Patents in suitUS 12,249,437
• Kohler Co. v. Delta Faucet Co.Some claims unpatentable
  PTAB · Oct 1, 2025 · IPR2024-00700 · APJ Jane E Inglese · IPR · Final written decision

  Claims 1, 2, and 9 are unpatentable as obvious; claims 3–8 and 10–24 were not shown unpatentable because the asserted references failed to establish limitations including the claimed light pipe features.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “For purposes of this Decision, we adopt Petitioner’s definition of a POSITA. Petitioner’s witness (Mr. Cook) qualifies as a POSITA under this definition, and, therefore, is qualified to opine from the perspective of a POSITA on technical matters included within the areas of expertise prescribed by the definition. As indicated above, Petitioner’s definition of a POSITA does not require education in the field of optics and professional experience designing or analyzing optical apparatus, unlike Patent Owner’s definition. We are aware, however, that Patent Owner’s witness (Dr. Klopp) has more extensive experience with optical systems and methods than Petitioner’s witness (Mr. Cook). Compare Ex 1003 ¶¶ 8–14, Ex. 2005, 39:21–59:17, with Ex. 2003 ¶¶ 3–20, Ex. 2004, 1–2, Ex. 1015, 10:22–13:25. Although Mr. Cook possesses excellent credentials in the field of mechanical engineering, his experience in the design and analysis of optical systems and methods is sparse and insubstantial compared to that of Dr. Klopp. Id. Due to this difference in experience levels, in instances where the witnesses express differing views on factual issues related to optical systems and methods, we will accord more weight to Dr. Klopp’s testimony than to Mr. Cook’s.” slip op. at 8

  • Expert testimonyPetitioner expert discountedPatent owner expert creditedMixed

    “through the light transmission portion and bottom output face 313 of light conductor 38, which teaches transmitting light in parallel with the longitudinal axis of the housing. Tseng does not disclose or teach that light is emitted through the side surface of annular protrusion 383 in a direction perpendicular to the longitudinal axis of the housing. Ex. 1004 ¶ 97. Petitioner’s assertions that this would be the case consist solely of conclusory statements, supported only by citations to Mr. Cook’s declaration. Mr. Cook, however, simply repeats Petitioner’s conclusory statements, without providing sound technical reasoning supported by objective evidence to explain and support his opinions. Ex. 2003 ¶¶ 101– 102, 105, 195–198, 202. We, therefore, accord little weight to Mr. Cook’s opinion on this particular matter because it “merely repeats, verbatim, the conclusory assertion for which it is offered to support,” and “does not cite to any additional supporting evidence or provide any technical reasoning [in] support.” Xerox Corp. v. Bytemark, Inc., IPR2022-00624, Paper 9 at 15 (PTAB Aug. 24, 2022) (precedential). Furthermore, Mr. Cook’s opinion conflicts with that of Patent Owner’s witness, Dr. Klopp, who opines that a “POSITA would understand from Tseng’s third embodiment that light from the LED would bypass the annular protrusion 383 of outer cliff 381, while transmitting downwardly toward the output face 313.” Compare Ex. 1003 ¶¶ 174–175, 190–194, with Ex. 2003 ¶¶ 101–102, 105. As discussed above, Mr. Cook is qualified to opine from the perspective of a POSITA on technical matters included within the expertise of a person meeting Petitioner’s definition of a POSITA, which do not include optics and optical apparatus. We, therefore, credit Dr. Klopp’s opinion over that of Mr. Cook on this particular factual issue of how it is directly related to optical systems and methods about which Mr. Cook possesses limited relevant experience. See Ex. 1003 ¶¶ 6–15 (experience in communication systems and electronics); Ex. 2005, 55:16–58:19 (design experience with electronics that use indicator lights or fiber-optic communications; no professional experience with light pipes, diffusers, or plumbing fixtures). Dr. Klopp possesses substantial research and professional experience with optical methods, fiber optic light pipes, light guides, diffusers, prisms, and analysis of faucets, spray heads, and plumbing fixtures. See Ex. 2003 ¶¶ 6–10 Supra 8 (discussing weight accorded to conflicting witness testimony); see also Resp. 2–3 (arguing that “Petitioner’s expert, Mr. Cook, is a mechanical engineer with substantial professional experience in electronics for high-voltage power systems and communications, but he has limited experience with the claimed subject matter.”).” slip op. at 34

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction needed

    “would be used to construe the claim[s] in a civil action [held] under 35 U.S.C. 282(b).” 37 C.F.R. § 42.100(b). Under that standard, claim terms generally are given their plain and ordinary meaning as would have been understood by the ordinarily skilled artisan at the time of the invention when read in the context of the specification and prosecution history. Phillips v. AWH Corp., 415 F.3d 1303, 1313 (Fed. Cir. 2005) (en banc). We construe terms in controversy only to the extent necessary to resolve the controversy. Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). Petitioner asserts that the claim terms do not require construction and should be afforded their plain and ordinary meaning. Pet. 13. Patent Owner contends that it applies the plain and ordinary meaning of the claim terms. Resp. 7. Taking into consideration the information presented, we determine that none of the claim terms requires express construction for purposes of resolving the dispute before us.” slip op. at 9

  • BurdenMixed

    “perpendicular to the longitudinal axis of Tseng’s housing (internal 33 and external 34 sleeves). “In an inter partes review, the burden of persuasion is on the petitioner to prove ‘unpatentability by a preponderance of the evidence,’ 35 U.S.C. § 316(e), and that burden never shifts to the patentee.” In re Magnum Oil Tools Int’l Ltd., 829 F.3d 1364, 1375 (Fed. Cir. 2016) (quoting Dynamic Drinkware, LLC v. Nat’l Graphics, Inc., 800 F.3d 1375, 1378 (Fed. Cir. 2015)); see also Aqua Products, Inc. v. Matal, 872 F.3d 1290, 1306 (Fed. Cir. 2017 (en banc (quoting Magnum Oil)).” slip op. at 40

  Patent outcomesUS 10,393,363 mixed
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,393,363

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.