• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00187 · APJ Debra L Dennett · IPR · Final written decision

  Claims 1–17 are unpatentable under § 103, principally because Chang in view of Jin renders them obvious; the Jin/Feldmann grounds were not shown.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49).” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11

  • Expert testimonyPatent owner expert creditedDecided for patent owner

    “gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard. Without an apparent reason to modify the teachings of Jin and Feldmann to” slip op. at 19

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 17

  Patent outcomesUS 10,230,009 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,230,009
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00006 · APJ Debra L Dennett · IPR · Final written decision

  Claims 1–17 are unpatentable under § 103, principally over Chang and Jin; the Board rejected the Jin and Feldmann combinations for lack of a reason to combine.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’009 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’009 patent and the prior art.” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 26. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 116 with Pet. 26). Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” See Magnum, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard.” slip op. at 19

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” Resp. 42 (citing Ex. 1013 ¶ 76). In so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Id. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Chang ¶ 62; Tr. 15:20–17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 73, 217 (citing Ex. 1023 § 1). Chang also discloses that the emitter area may be formed by thermal diffusion, ion implantation or the like. Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding a tunneling layer and a base surface field area from periphery region and isolation region. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” slip op. at 32

  Patent outcomesUS 10,230,009 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,230,009
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00918 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board rejected the Jin and Feldmann based grounds for lack of a reason to combine without hindsight.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “Patent Owner focuses on Chang’s description in paragraph 76 of a single configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” PO Resp. 42–43 (citing Ex. 1013 ¶ 76). But, in so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Ex. 1013 ¶ 62; Tr. 15:20– 17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 70–81, 91–96, 200 (citing Ex. 1026 § 1 and stating that “[b]oth Chang and Jin likewise teach backside isolation regions”). Chang also discloses that the emitter area may be formed by “thermal diffusion, ion implantation or the like.” Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Pet. Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding the second tunneling layer and a base surface field area from periphery region and isolation portion. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art “reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” Ex. 1003 ¶ 201.” slip op. at 33

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00186 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board found the combination disclosed the claimed isolation portion and supported the challenged claims.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “C. Claim Construction We construe claim terms according to the standard set forth in Phillips v. AWH Corp., 415 F.3d 1303, 1312–17 (Fed. Cir. 2005) (en banc); 37 C.F.R. § 42.100(b). Under Phillips, we give claim terms “their ordinary and customary meaning.” Phillips, 415 F.3d at 1312. “[T]he ordinary and customary meaning of a claim term is the meaning that the term would have to a person of ordinary skill in the art in question at the time of the invention.” Id. at 1313. “Importantly, the person of ordinary skill in the art is deemed to read the claim term not only in the context of the particular claim in which the disputed term appears, but in the context of the entire patent, including the specification.” Id. Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Expert testimonyPetitioner expert discountedPatent owner expert creditedMixed

    “edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001” slip op. at 18

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00007 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under §103 over Chang and Jin because the combination teaches the claimed isolation portion and the claimed tapering.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedOther

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightTeaching away not foundNot shown unpatentable

    “On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  • Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner

    “However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide.” slip op. at 18

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• Bio-Rad Laboratories, Inc. v. California Institute Of TechnologyNo claims unpatentable
  PTAB · Mar 23, 2026 · IPR2024-01451 · APJ Tawen Chang · IPR · Final written decision

  Claims 1–19 were not shown unpatentable: Larson did not establish the claimed detection in a single sample volume, and the asserted obviousness combinations did not cure the deficiencies.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Patent Owner states that, “[f]or purposes of this IPR proceeding, PO does not contest Petitioner’s description of qualifications for a person of ordinary skill in the art (POSA) set forth [above].” PO Resp. 23. In view of the above, and because Petitioner’s uncontested description of one of ordinary skill in the art is reasonable and consistent with the ’921 patent and the cited art, we adopt Petitioner’s definition of a POSA for purposes of this Decision, except that we replace the phrase “at least a year of experience in quantitative and/or dPCR and fluorescence-based analyte detection” with “around a year of experience in quantitative and/or dPCR and fluorescence-based analyte detection.” Pet. 9 (emphasis added).13” slip op. at 14

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

    “We begin with “the context in which a term is used in the asserted claim,” which can be “highly instructive.” Phillips, 415 F.3d at 1314. In this case, claim 1 recites that the claimed assay is “capable of unambiguously detecting the presence or absence of each of said at least M analytes, in any combination of presence or absence, in a single sample volume, . . . wherein the analytes are amplified in the single sample 15 In this regard, we note that Petitioner’s claim construction position is not predicated on the collection of droplets being reconstituted into its original, pre-partition form prior to amplification; rather, the droplets remain compartmentalized from each other in the PCR thermal cycling tube. Tr. 65:21–66:9 (Petitioner’s counsel explaining that the droplets do not combine in the PCR thermal cycling tube but, rather, are “suspended in an immiscible fluid and analyzed en masse”). indicates that the first instance of single sample volume, i.e., the single sample volume in which the presence or absence of each M analytes are to be detected, is the antecedent basis for the second instance of “single sample volume,” i.e., the single sample volume in which the analytes are amplified. Thus, as the parties appear to agree, the single sample volume in which amplification takes places must be the same single sample volume in which the presence or absence of analytes are to be detected. We are not persuaded that, when accorded its plain and ordinary meaning, a single sample volume divided into a collection of droplets would be considered the “same” single sample volume prior to its partition.” slip op. at 17

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

    “With respect to the limitation, “wherein the analytes are amplified in the single sample volume,” Petitioner asserts that “Larson discloses PCR assays that amplify target polynucleotide in a single sample volume, specifically a portion of the reaction mixture that is subsequently partitioned into droplets.” Pet. 31 (emphasis added). There is no dispute that the amplification of the analytes in Larson occurs in the droplets. Larson ¶¶ 6–7 (explaining that “[d]igital PCR (dPCR) is an alternative quantitation method in which dilute sample are divided into many separate reactions” and that “[t]he template is amplified in the droplet for detection”) (emphasis added). Because the claims require that amplification of the analytes be in the same sample volume in which the at least M analytes, in any combination of presence or absence, is unambiguously detected, and because the pre-partition single sample volume is not the same single sample volume as the collection of droplets after partition under our claim construction set forth above, we find Petitioner has not shown, by a preponderance of evidence, that claims 1–10 and 13–19 are anticipated by Larson.17 Tr. 68:12–69:14 (Petitioner’s counsel” slip op. at 27

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable

    “Although we agree with Petitioner that Larson contemplates scenarios in which droplets may contain more than one target molecule and does not require the exclusion of such multiple occupancy droplets in all embodiments, we are nevertheless not persuaded Petitioner has shown, based on a preponderance of evidence, that Larson renders obvious an assay capable of unambiguously detecting, in such multiple occupancy droplets, the presence or absence of each of at least M analytes, in any combination of presence or absence, when M is greater than F and F is at least 2.” slip op. at 32

  Patent outcomesUS 11,827,921 not shown unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 11,827,921
• Samsung Display Co., Ltd. v. Pictiva Displays International Ltd.All claims unpatentable
  PTAB · Jan 22, 2026 · IPR2024-01093 · APJ Grace Karaffa Obermann · IPR · Final written decision

  Claims 1–16 are unpatentable: claims 1–13 and 15–16 on anticipation and obviousness grounds, and claim 14 on obviousness over Choulis.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “A person of ordinary skill in the art (“POSITA”) at the time of the alleged invention of the ’164 patent would have had a Bachelor’s degree in chemistry, physics, or a comparable field of study, and at least three years of research or industrial experience with organic optoelectronic light-emitting devices. An individual with additional education could have less research or industrial experience and vice versa. Pet. 12. Patent Owner repeatedly refers to “a POSITA” without addressing the definition of that term or contesting Petitioner’s proposed definition. See Resp. 1, 2 n.1, 3, 8, 9, 15–21, 23, 26, 29, 32–33, 35, 37, 38, 40, 41, 44–49, 51–57, 61, 62 (bare references to “a POSITA”). Neither party indicates that the ultimate result on patentability would change depending on the definition selected. We adopt Petitioner’s proposed definition, which is not contested, because it is consistent with the disclosures of the asserted prior art. See Ex. 1004, (code 57); Ex. 1006, code (57); Ex. 1008, code (57); Ex. 1009, code (57) (abstracts of the references asserted in the patentability challenges).” slip op. at 7

  • Claim Construction › Intrinsic evidence (Phillips canons) › Specification disavowal / 'present invention' languageDisclaimer not foundTerm construed board ownDecided for petitioner

    “because no information raised during the trial phase of this review changes the calculus: First and foremost, the plain terms of claim 1 include no language from which we reasonably can impose limits on the phrase “matrix material” as urged by Patent Owner. In addition, the specification includes no special definition of that phrase that supports importing Patent Owner’s proposed narrowing limitation into the claim. Furthermore, we are directed to no disclaimer of claim scope during patent prosecution that would support Patent Owner’s twice-rejected argument that the phrase “matrix material” in claim 1 excludes embedded dopants and dispersed agglomerations. And the extrinsic evidence advanced by Patent Owner during this review is ineffective to override the clear interpretation of “matrix material” that is established by the intrinsic evidence. Reply 1–7.10” slip op. at 8

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableNot shown unpatentableMixed

    “We find that Petitioner establishes by a preponderance of the evidence that Choulis anticipates claim 13. We agree with Petitioner, in that regard, that Choulis explicitly teaches “using spin-coating as a method for depositing materials, which involves a simultaneous application process” as required by claim 13. Reply 16 (citing Pet. 40–41; Ex. 1044 ¶ 45).16 We 15 Petitioner raises Djobo as a background reference supporting that Choulis anticipates deposition of PVK by evaporation. Pet. 41. Patent Owner counters that Djobo, to the contrary, shows that Choulis does not teach deposition of PVK by evaporation. Resp. 48. In other words, both parties cite Djobo in connection with the ground based on anticipation by Choulis. Against that backdrop, we determine that Patent Owner waives any argument that Petitioner improperly cites Djobo as a background reference in support of the anticipation challenge, which is based on Choulis alone. Resp. 48 (nowhere asserting that the challenge is deficient on that basis). That waiver arises because no argument, in that regard, is raised in Patent Owner’s Response see Inst. Dec. 34 (“The Board shall deemed waived any issue not raised by Patent Owner in a timely response to the Petition . . . .”). 16 Patent Owner’s statement that “spin coating tends to cause phase separation” is not developed adequately on this record and, therefore, is further agree with Petitioner that Patent Owner “has not contested this point.” Resp. 48. “Therefore, there is no genuine dispute regarding the unpatentability of claim 13,” although Patent Owner raises “arguments concerning evaporation, which is a distinct process from spin-coating” relevant to the additional limitations of claim 14. Reply 16. We determine that Petitioner establishes by a preponderance of the evidence that Choulis anticipates claim 13. Patent Owner, however, has the better position on whether Choulis anticipates claim 14, which “includes the requirement of applying matrix materials via evaporation coating.” Reply 16. Petitioner seems to abandon that challenge in the Reply by raising arguments that appear, on this record, to bear exclusively on whether the subject matter of claim 14 would have been obvious over Choulis.17 Id. at 16–17. Those arguments are insufficient to counter Patent Owner’s reasons why Choulis does not anticipate the “evaporation coating” limitation of claim 14. Compare id., with Resp. 48. On this record, therefore, we determine that Petitioner does not establish by a preponderance of the evidence that Choulis anticipates claim 14. unpersuasive to persuade us “that Choulis does not have three matrix materials.” Sur-reply 15. That argument runs counter to Choulis’s explicit, intrinsic disclosures, which illustrate (Ex. 1004, Fig. 4) and describe (id. ¶ 30) an organic light emitting layer composed of three matrix materials. See Pet. 24–25 (citing Ex. 1004, Fig. 4, ¶ 30); see also Ex. 1003 ¶¶ 85–88 (persuasive declaration testimony of Dr. Holmes, cited at Pet. 24–25). 17 There is some confusion on this point, given that both parties sometimes collapse, into a single argument, whether Choulis anticipates or renders obvious claim 1. Compare Resp. 48, with Reply 16–17.” slip op. at 35

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “On this record, therefore, we determine that Choulis, at minimum, suggests that a person of ordinary skill in the art at the time of the invention would have recognized PMMA as a suitable alternative to PVK in Choulis’s Figure 4 embodiment, notwithstanding any differences raised by Patent Owner. Ex. 1004 ¶ 44. Patent Owner’s argument that no disclosure in Choulis suggests that an ordinarily skilled artisan “would have found it desirable to use PMMA in place of PVK in Choulis’s devices” misses the mark, where Choulis includes both PMMA and PVK in lists of materials suitable for use as host or matrix materials. Resp. 38; Ex. 1004 ¶ 44. “Our caselaw is clear. It’s not necessary to show that a combination is ‘the best option, only that it is a suitable option.’” Intel Corp. v. Qualcomm Inc., 21 F.4th 784, 800 (Fed. Cir. 2021). Even if Choulis does not expressly disclose substituting PMMA for PVK in the Figure 4 embodiment, “an ordinarily skilled artisan would have found it obvious to make that substitution.” Reply 10 (citing Pet. 31 (citing Ex. 1003 ¶ 100; Ex. 1044 ¶ 23)). The suggestion for that substitution is set forth unambiguously in Choulis’s listing of both “PVK” and “PMMA” as materials suitable for use as a first “host” material in Choulis’s organic functional layer; that is, “the light emitting layer” that is “described above” in Figure 4. Ex. 1004 ¶ 44. ii. Alternative Reasoning for Replacing PVK with PMMA Patent Owner counterargues that using PPMA in place of PVK would have been understood to “upset the hole and electron balance,” as well as “affect hole-charge recombination,” and “degrade the performance of the resulting OLED system.” Resp. 37. Petitioner responds with evidence that “it would have been a routine task for” an ordinarily skilled artisan “to optimize the composition of each component within the light-emitting layer to achieve the desired charge balance.” Reply 11 (citing Ex. 1004 ¶ 24). Petitioner’s response brings to light a second reason why an ordinarily” slip op. at 40

  Patent outcomesUS 8,723,164 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 8,723,164
• Kohler Co. v. Delta Faucet Co.Some claims unpatentable
  PTAB · Oct 1, 2025 · IPR2024-00700 · APJ Jane E Inglese · IPR · Final written decision

  Claims 1, 2, and 9 are unpatentable as obvious; claims 3–8 and 10–24 were not shown unpatentable because the asserted references failed to establish limitations including the claimed light pipe features.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “For purposes of this Decision, we adopt Petitioner’s definition of a POSITA. Petitioner’s witness (Mr. Cook) qualifies as a POSITA under this definition, and, therefore, is qualified to opine from the perspective of a POSITA on technical matters included within the areas of expertise prescribed by the definition. As indicated above, Petitioner’s definition of a POSITA does not require education in the field of optics and professional experience designing or analyzing optical apparatus, unlike Patent Owner’s definition. We are aware, however, that Patent Owner’s witness (Dr. Klopp) has more extensive experience with optical systems and methods than Petitioner’s witness (Mr. Cook). Compare Ex 1003 ¶¶ 8–14, Ex. 2005, 39:21–59:17, with Ex. 2003 ¶¶ 3–20, Ex. 2004, 1–2, Ex. 1015, 10:22–13:25. Although Mr. Cook possesses excellent credentials in the field of mechanical engineering, his experience in the design and analysis of optical systems and methods is sparse and insubstantial compared to that of Dr. Klopp. Id. Due to this difference in experience levels, in instances where the witnesses express differing views on factual issues related to optical systems and methods, we will accord more weight to Dr. Klopp’s testimony than to Mr. Cook’s.” slip op. at 8

  • Expert testimonyPetitioner expert discountedPatent owner expert creditedMixed

    “through the light transmission portion and bottom output face 313 of light conductor 38, which teaches transmitting light in parallel with the longitudinal axis of the housing. Tseng does not disclose or teach that light is emitted through the side surface of annular protrusion 383 in a direction perpendicular to the longitudinal axis of the housing. Ex. 1004 ¶ 97. Petitioner’s assertions that this would be the case consist solely of conclusory statements, supported only by citations to Mr. Cook’s declaration. Mr. Cook, however, simply repeats Petitioner’s conclusory statements, without providing sound technical reasoning supported by objective evidence to explain and support his opinions. Ex. 2003 ¶¶ 101– 102, 105, 195–198, 202. We, therefore, accord little weight to Mr. Cook’s opinion on this particular matter because it “merely repeats, verbatim, the conclusory assertion for which it is offered to support,” and “does not cite to any additional supporting evidence or provide any technical reasoning [in] support.” Xerox Corp. v. Bytemark, Inc., IPR2022-00624, Paper 9 at 15 (PTAB Aug. 24, 2022) (precedential). Furthermore, Mr. Cook’s opinion conflicts with that of Patent Owner’s witness, Dr. Klopp, who opines that a “POSITA would understand from Tseng’s third embodiment that light from the LED would bypass the annular protrusion 383 of outer cliff 381, while transmitting downwardly toward the output face 313.” Compare Ex. 1003 ¶¶ 174–175, 190–194, with Ex. 2003 ¶¶ 101–102, 105. As discussed above, Mr. Cook is qualified to opine from the perspective of a POSITA on technical matters included within the expertise of a person meeting Petitioner’s definition of a POSITA, which do not include optics and optical apparatus. We, therefore, credit Dr. Klopp’s opinion over that of Mr. Cook on this particular factual issue of how it is directly related to optical systems and methods about which Mr. Cook possesses limited relevant experience. See Ex. 1003 ¶¶ 6–15 (experience in communication systems and electronics); Ex. 2005, 55:16–58:19 (design experience with electronics that use indicator lights or fiber-optic communications; no professional experience with light pipes, diffusers, or plumbing fixtures). Dr. Klopp possesses substantial research and professional experience with optical methods, fiber optic light pipes, light guides, diffusers, prisms, and analysis of faucets, spray heads, and plumbing fixtures. See Ex. 2003 ¶¶ 6–10 Supra 8 (discussing weight accorded to conflicting witness testimony); see also Resp. 2–3 (arguing that “Petitioner’s expert, Mr. Cook, is a mechanical engineer with substantial professional experience in electronics for high-voltage power systems and communications, but he has limited experience with the claimed subject matter.”).” slip op. at 34

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction needed

    “would be used to construe the claim[s] in a civil action [held] under 35 U.S.C. 282(b).” 37 C.F.R. § 42.100(b). Under that standard, claim terms generally are given their plain and ordinary meaning as would have been understood by the ordinarily skilled artisan at the time of the invention when read in the context of the specification and prosecution history. Phillips v. AWH Corp., 415 F.3d 1303, 1313 (Fed. Cir. 2005) (en banc). We construe terms in controversy only to the extent necessary to resolve the controversy. Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). Petitioner asserts that the claim terms do not require construction and should be afforded their plain and ordinary meaning. Pet. 13. Patent Owner contends that it applies the plain and ordinary meaning of the claim terms. Resp. 7. Taking into consideration the information presented, we determine that none of the claim terms requires express construction for purposes of resolving the dispute before us.” slip op. at 9

  • BurdenMixed

    “perpendicular to the longitudinal axis of Tseng’s housing (internal 33 and external 34 sleeves). “In an inter partes review, the burden of persuasion is on the petitioner to prove ‘unpatentability by a preponderance of the evidence,’ 35 U.S.C. § 316(e), and that burden never shifts to the patentee.” In re Magnum Oil Tools Int’l Ltd., 829 F.3d 1364, 1375 (Fed. Cir. 2016) (quoting Dynamic Drinkware, LLC v. Nat’l Graphics, Inc., 800 F.3d 1375, 1378 (Fed. Cir. 2015)); see also Aqua Products, Inc. v. Matal, 872 F.3d 1290, 1306 (Fed. Cir. 2017 (en banc (quoting Magnum Oil)).” slip op. at 40

  Patent outcomesUS 10,393,363 mixed
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,393,363
• Padagis US LLC v. Neurelis, Inc.Instituted
  PTAB · Sep 16, 2025 · IPR2025-00466 · APJ Timothy G Majors · IPR · Institution

  The Board instituted IPR on claims 1–27 because Petitioner showed a reasonable likelihood of prevailing on at least one claim, including claim 1 over Gwozdz and Meezan.

  RulingsInstitution decision

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted

    “Under 35 U.S.C. § 314(a), an inter partes review may not be instituted unless it is determined that there is a reasonable likelihood that the petitioner will prevail with respect to at least one of the claims challenged in the petition. For reasons explained below, we conclude that Petitioner shows a reasonable likelihood that it will prevail with respect to at least one of the ’786 patent’s challenged claims.1 We institute inter partes review on all challenged claims. SAS Inst. Inc. v. Iancu, 584 U.S. 357, 362–63 (2018); 37 C.F.R. § 42.108(a) (“When instituting inter partes review, the Board will authorize the review to proceed on all of the challenged claims and on all grounds of unpatentability asserted for each claim.”).” slip op. at 2

  • Disclosure Requirements (§112) › Written description (Ariad)Not entitled to earlier dateDecided for petitioner

    “We find that Petitioner has made a threshold showing that the ’558 Provisional does not provide written description support for claim 1’s pharmaceutical solution consisting of each of the recited elements, including n-dodecyl beta-D-maltoside. It is true that “n-Dodecyl β-D-maltoside” can be found listed in the SIGMA Catalog. Ex. 1026, 316. But Dr. Donovan’s testimony helps put that listing in context. It is merely one among well over 100 ionic and non-ionic detergents listed in the cited six pages of the SIGMA Catalog. See 1026, 316–321; Ex. 1062 ¶ 50. When further considered in the context of paragraphs 150–152 of the ’558 Provisional, which generically suggest that “enhancer” compounds can be used in “some embodiments”—then introducing at least 15 classes of potential enhancers16 including “preferred” lysophospholipids and acyl carnitines—the listing of n-dodecyl beta-D-maltoside among at least 150 biological detergents in the SIGMA Catalog is even more remote. Moreover, although satisfaction of the written description requirement is not limited to what is exemplified in a priority application, none of the ’558 Provisional’s examples use any “enhancer,” much less any detergent, any alkyl glycoside, or n-dodecyl beta-D maltoside in particular. The 16 The ’558 Provisional suggests that whether “a given compound” will function as an “enhancer” in a formulation requires testing. Ex. 1008 ¶ 150 (indicating “an in vivo or good model test” may “determin[e] whether the uptake of the drug is enhanced to a clinically significant degree”). ethanol. See Ex. 1008 ¶¶ 172–174 (Examples 1 and 2). In short, we find no sufficient disclosure of “blaze marks” in the ’558 Provisional that point to the inventors’ possession of a pharmaceutical solution that includes n-dodecyl beta-D-maltoside as claimed. Purdue Pharma L.P. v. Faulding Inc., 230 F.3d 1320, 1326–27 (Fed. Cir. 2000) (analogizing an application’s generic disclosures to a forest of unmarked trees and explaining that, “to satisfy the written description requirement,” there must be “blaze marks directing the skilled artisan to that tree [within the forest that represents the claimed invention]” in the application).” slip op. at 28

  • PTAB / AIA Trials › §315(e) estoppelEstoppel does not applyDecided for patent owner

    “and applying collateral estoppel to vacate a claim construction in an underlying IPR). In an IPR, “a party seeking to invoke collateral estoppel must show: ‘(1) the issue is identical to one decided in the first action; (2) the issue was actually litigated in the first action; (3) resolution of the issue was essential to a final judgment in the first action; and (4) [the party against whom collateral estoppel is being asserted] had a full and fair opportunity to litigate the issue in the first action.’” Google LLC v. Hammond Development Int’l, Inc., 54 F.4th 1377, 1381 (Fed. Cir. 2022) (quoting In re Freeman, 30 F.3d 1459, 1465 (Fed. Cir. 1994)) (alteration in original).14 “It is [also] well established that patent claims need not be identical for collateral estoppel to apply.” Id. at 1381. Instead, “collateral estoppel requires the issues of patentability be identical.” Id. If “the differences between the unadjudicated patent claims and adjudicated patent claims do not materially alter the question of invalidity, collateral estoppel applies.” Ohio Willow Wood Co. v. Alps South, LLC, 735 F.3d 1333, 1342–43 (Fed. Cir. 2013) (affirming application of collateral estoppel where claims adjudicated as obvious required a “polymeric” gel whereas similar, unadjudicated claims required a “block copolymer” gel). “Collateral estoppel also applies to common issues in actions involving different but related patents.” Mycogen Plant Sci., Inc. v. Monsanto Co., 252 F.3d 1306, 1310 (Fed. Cir. 2001), vacated on other grounds, 353 U.S. 1109 (2002).” slip op. at 22

  • Novelty / Anticipation (§102) › Prior-art status of a reference › Patents / published applications (effective date, provisional support)Reference is prior artReference not prior artMixed

    “We agree that at least one portion of Gwozdz is not prior art. To establish that the cited disclosures in Gwozdz are prior art, Petitioner must show support for those disclosures in the Gwozdz Provisional. In re Riggs, 131 F.4th 1377, 1384 (Fed. Cir. 2025) (explaining that “the portion of the application relied on . . . as prior art must be supported by the provisional application”). Petitioner did not establish that Gwozdz’s disclosure of “penetration enhancers” finds support in the Gwozdz Provisional. Pet. 22. Conversely, Patent Owner shows that the phrase is absent in the Gwozdz Provisional. Prelim. Resp. 37.20 Based on this record, we determine that Gwozdz’s mention of “penetration enhancers” is not prior art to the 19 Patent Owner argues this “penetration enhancers” disclosure in Gwozdz is not prior art regardless which of the disputed priority dates (March 28, 2008, or March 27, 2009) one accords to the challenged claims. Prelim. Resp. 33. 20 We also agree that collateral estoppel does not bar Patent Owner from challenging Gwozdz’s prior-art status in this case. Patent Owner’s apparent concession that Gwozdz was prior art during the 451 IPR does not equate to the issue being actually litigated. Prelim. Resp. 34–35; Ex. 1040, 14 (“Patent Owner does not contest that Gwozdz is entitled to this filing date” of the Gwozdz Provisional). Purdue, 767 F. App’x at 922 (determining “[t]he priority date for the Joshi reference . . . cannot be determined based on collateral estoppel” where patentee could have argued, but did not in fact argue, Joshi’s prior-art status in an earlier matter).” slip op. at 35

  Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites KSR · Graham
  Patents in suitUS 11,793,786
• Inergy Technology, Inc. v. Force Mos Technology Co., Ltd.No claims unpatentable
  PTAB · May 16, 2025 · IPR2024-00093 · APJ Grace Karaffa Obermann · IPR · Final written decision

  Claims 1–9 were not proven unpatentable because the asserted references did not establish the claimed epitaxial layer or the required coverage of the trench sidewalls.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner defines a person of ordinary skill in the art as having “a Master’s degree in electrical engineering, and at least two years of relevant work experience in the field of integrated circuit design and manufacturing.” Pet. 13 (citing Ex. 1003 ¶¶ 32–37, 57). Patent Owner does not dispute Petitioner’s definition. PO Resp. 6. We adopt Petitioner’s proposed definition of the level of ordinary skill in the art because it is supported by unopposed declaration testimony and appears to be consistent with the disclosures of the ’634 patent and the asserted prior art references. See Ex. 1001, 1:6–2:33 (describing the invention and related art in terms of integrated circuit design and fabrication); see also Ex. 1006 ¶¶ 1–6 (Hirler); Ex. 1008 ¶¶ 1–37 (Kobayashi); Ex. 1009 ¶¶ 2–29 (Shiraishi). Neither party, moreover, indicates the overall result would change based on a different definition.” slip op. at 7

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “Petitioner argues that “the sidewalls of said trenches in said base layer are covered” should be construed to mean that “the entire sidewalls of” those trenches are covered. Pet. 18–19. We refer to this as “the sidewall limitation.” Petitioner shows persuasively that the disclosure and file history of the ’634 patent support its position on the sidewall limitation. Id. Patent Owner, for its part, observes that, after the filing of the Petition. two District Courts adopted the construction proposed by Petitioner.” PO Resp. 21 (citing Ex. 2010, 6–9; Ex. 2011, 23). Patent Owner also agrees to apply Petitioner’s construction for purposes of this proceeding. Id. We agree with Patent Owner that an express construction of the sidewall limitation is necessary to this Decision, id., and adopt Petitioner’s undisputed definition because it is supported by the record. No other claim term requires express construction for purposes of this Decision.” slip op. at 8

  • BurdenNot shown unpatentable

    “On this record, Petitioner fails to demonstrate that any claim is unpatentable under any ground asserted in the Petition. IV. CONCLUSION For the above reasons, we determine that Petitioner fails to establish by a preponderance of the evidence that claims 1–9 of the ’634 patent are unpatentable.” slip op. at 34

  • Expert testimonyPetitioner expert discountedPatent owner expert creditedDecided for patent owner

    “Alternatively, even if we set aside that timing issue, Dr. Liu’s bare opinion, advanced for the first time during cross-examination, that an epitaxial layer is “obvious” from Hirler’s disclosure is inadequate to support the challenges. Id. at 24–25. We accord little weight to Dr. Liu’s opinion because it is conclusory. See Xerox Corp. v. Bytemark, Inc., IPR2022-00624, Paper 9 at 15 (PTAB Aug. 24, 2022) (precedential). In any event, Petitioner does not meet, on this record, the “high standard” required to establish an inherent disclosure of an epitaxial layer in Hirler. PO Resp. 24.6 Dr. Liu opined for the first time during cross-examination “that it would have been impossible to create Hirler’s more lightly doped n- drift zone layer on top of its more heavily doped n+ substrate layer other than via epitaxy.” Id. at 25 (citing Ex. 2014, 164:16– 165:20). But Patent Owner effectively refutes that proposition with evidence that such a layer “could be created by counter-doping,” even if, as Dr. Liu contends, counter-doping may have been less ideal due to “disadvantageous mobility.” Id. (citing Ex. 2012 ¶ 133; Ex. 2014, 166:15–167:8).” slip op. at 11

  Patent outcomesUS 7,629,634 not shown unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 7,629,634

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.