- Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing deniedPTAB · Oct 7, 2025 · IPR2024-01462 · APJ Jo-Anne M Kokoski · IPR · Rehearing
The Board denied Solus’s rehearing request, leaving institution denied for claims 1–8 because the petition did not adequately show motivation to combine Hanafusa and Dobashi.
RulingsRehearing decision- RehearingRehearing, deniedDenied
“of the decision de novo, but instead review the decision for an abuse of discretion. 37 C.F.R. § 42.71(c). An abuse of discretion may be determined “if a decision is based on an erroneous interpretation of law, if a factual finding is not supported by substantial evidence, or if the decision represents” slip op. at 2
- Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable
“In particular, neither Petitioner nor Dr. Josefowicz adequately explain why a POSITA looking for ways to make Hanafusa’s surface roughness low-profile would look to methods to achieve Dobashi’s RSm values. Dobashi teaches that because RSm “can be adopted as the period of waviness, RSm can also be used as an indicator for judgment of the surface.” Ex. 1005, 2:66–3:1, 6:23–26. Dobashi explains that waviness is “an indicator for determining whether the fine pattern forming performance is good or bad,” and “[t]he surface has small waviness and is smooth when RSm is large, and the surface has large waviness Dobashi also teaches that surface roughness Rzjis is used as a low-profile indicator. Ex. 1005, 2:66–3:1. Dobashi, therefore, teaches that RSm is an indicator of surface waviness, which Dobashi explains is different than surface roughness. Id. at 2:66– 3:3, 6:23–29. Given these teachings in Dobashi, neither Petitioner nor Dr. Josefowicz sufficiently explains how or why a POSITA would have been motivated to implement Dobashi’s RSm values to make Hanafusa’s surface roughness low-profile. See Pet. 10–12; Ex. 1003 ¶¶ 46–52.” slip op. at 4
§ 103 obviousnessPatents in suitUS 11,346,014 - Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing deniedPTAB · Oct 7, 2025 · IPR2024-01461 · APJ Jo-Anne M Kokoski · IPR · Rehearing
The Board denied rehearing and left in place its denial of institution because Petitioner did not show that claims 1–10 were likely obvious over the asserted combinations.
RulingsRehearing decision- RehearingRehearing, deniedDenied
“II. STANDARD OF REVIEW When rehearing a decision on institution, we do not review the merits of the decision de novo, but instead review the decision for an abuse of discretion. 37 C.F.R. § 42.71(c). An abuse of discretion may be determined “if a decision is based on an erroneous interpretation of law, if a factual finding is not supported by substantial evidence, or if the decision represents an unreasonable judgment in weighing relevant factors.” Arnold Partnership v. Dudas, 362 F.3d 1338, 1340 (Fed. Cir. 2004) (citing In re 1 US 2013/0108922 A1, published May 2, 2013 (Ex. 1004, “Shinozaki”). 2 G. Khatibi, Temperature Dependent Elastic and Thermal Properties of Thin Copper Foils, Copper; Proceedings of the International Conference Copper ’06 (2006) (Ex. 1006, “Khatibi”). 3 Korean Patent Pub. No. 10-2012-0003485, published Jan. 10, 2012 (Ex. 1013; Ex. 1014 (English translation), “Toshio”). 4 US 2013/0108887 A1, published May 2, 2013 (Ex. 1012, “Kim”). 5 Griesi, M.B., Characterization of Electrodeposited Copper Foil Surface Roughness for Accurate Conductor Power Loss Modeling (2014) (Master’s Thesis, University of South Carolina) (Ex. 1015, “Griesi”). rehearing has the burden to show that the decision should be modified. 37 C.F.R. § 42.71(d). Additionally, the request for rehearing “must specifically identify all matters the party believes the Board misapprehended or overlooked, and the place where each matter was previously addressed in a motion, an opposition, or a reply.” Id.” slip op. at 2
- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Not shown unpatentable
“For example, Dr. Randall does not provide adequate explanation or objective evidence to support his opinion that Khatibi’s use of a laser speckle based dilatometer instead of the claimed thermomechanical analyzer “is unlikely to significantly impact the CTE[6] value” because “variations in equipment and a heating speed of 5° C/min would not significantly alter the results.” Ex. 1003 ¶ 58. In particular, Dr. Randall neither explains what constitutes a “significant” impact on CTE, nor provides objective evidence to support his contention that equipment variations and heating differences would not “significantly alter” the resulting measurements. And although Dr. Randall opines that “the heating rate (5°C per minute) is typical for certain devices” such as a thermomechanical analyzer or dilatometer, and “[t]ypically, these devices use temperature ramp rates between 2°C and 20°C per minutes, so the ‘5° C./min’ recited in [1d] is common and should not drastically affect the measurement results,” Dr. Randall fails to point us to any evidence showing that these temperatures are “typical” or that the claimed heating rate is “common.” Id. ¶ 59 (emphases added).” slip op. at 4
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable
“Petitioner, however, does not adequately explain why a POSITA would have been motivated to modify Kim’s copper foil surface to have a Pc value of 19.2 as reported in Griesi. In particular, neither Petitioner nor Dr. Randall points us to, nor do we discern, any teaching in Griesi that a peak count of 19.2 provides any particular benefits or properties that would have lead a POSITA to modify Kim’s copper foil surface as Petitioner proposes. Instead, Petitioner’s arguments that a POSITA would have been motivated to modify Kim’s copper foil surface with Griesi’s peak count patent itself. See KSR Int’l Co. v. Teleflex Inc., 550 U.S. 398, 421 (2007) (stating that the fact finder must be aware “of the distortion caused by hindsight bias and must be cautious of arguments reliant upon ex post reasoning”). It was Petitioner’s burden to establish that the combined teachings Kim and Griesi disclose limitation [1g] as proposed. We are not persuaded that we misapprehended Petitioner’s argument when we determined that Petitioner did not meet that burden.” slip op. at 8
- BurdenDecided for patent owner
“It was Petitioner’s burden to establish the Khatibi, alone or in combination with Shinozaki, Toshio, and Kim, discloses limitation [1d]. We concluded that Petitioner failed to meet that burden for the reasons explained in our Decision. We are not persuaded that we overlooked or misapprehended Khatibi’s disclosures, or Petitioner’s evidence and explanation thereof, in doing so.7” slip op. at 5
§ 103 obviousnesscites KSRPatents in suitUS 10,811,689 - PTAB · Sep 19, 2025 · PGR2025-00025 · APJ Kimberly Mcgraw · PGR · Institution
The Board instituted PGR on claims 1–19 and all asserted grounds, finding it more likely than not that claim 1 is anticipated by the Gatorade Label.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“if “the information presented in the petition . . . demonstrate[s] that it is more likely than not that at least 1 of the claims challenged in the petition is unpatentable.” Post-grant review is available for patents that issue from applications that at one point contained at least one claim with an effective filing date on or after March 16, 2013. See Leahy-Smith America Invents Act, Pub. L. No. 112-29, 125 Stat. 284 (2011) (“AIA”), §§ 3(n)(1), 6(f)(2)(A). After considering the briefing and the evidence of record, for the reasons set forth below, we determine that Petitioner has shown that the ’422 Patent is eligible for post-grant review and has shown it is more likely than not that at least one challenged claim of the ’422 Patent is unpatentable under § 324(a). Accordingly, we institute a post-grant review of the challenged claims of the ’422 Patent.” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“B. Level of Ordinary Skill in the Art Petitioner contends that a person of ordinary skill in the art “would possess at least (1) a Bachelor’s degree in chemistry or a related field, with (2) five years of experience in material identification and characterization using multiple analytical methods and field sampling, or equivalent research or professional experience.” Pet. 12 (citing Ex. 1014 ¶ 24). Patent Owner does not dispute Petitioner’s definition for one of ordinary skill in the art nor provide a proposed definition of its own. See generally Prelim. Resp. For the purposes of this Decision, we adopt Petitioner’s undisputed proposal regarding the level of one of ordinary skill in the art.” slip op. at 7
- Claim Construction › Intrinsic evidence (Phillips canons) › Prosecution history disclaimer / disavowalDisclaimer foundDecided for patent owner
“336. The applicant explained that not all combinations of shrink films and light blocking materials are recyclable. Id. at 335. The applicant explained that films can be compatible with PET recycling in two ways, (1) the film can float in water and be separated from PET that sinks in water or (2) the PET films crystallize and “can be recovered with the PET stream.” Id. at 336 (citing “A Resource Document by the Association of Plastic Recyclers (APR)”) (found at Ex. 1002, 323–332) (emphasis omitted). The applicant explained that “removing the label before or during the recycling process is not evidence of the recyclability of the label” and that “[r]emoving the label during the recycling process is not equivalent to actually recycling the label.” Id. at 335. As such, a POSITA reading the prosecution history would understand that a label is not recyclable with a PET container, as recited by the independent claims, by removing the label from the PET recycle stream before or during the recycling process.” slip op. at 10
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed board ownOther
“To determine how a person skill in the art would determine if a shrink label is “recyclable” as recited in the independent claims, we look to how the Specification of the ’422 Patent describes or defines recyclable shrink labels. For example, the ’422 Patent states that PET shrink films are generally considered recyclable if no inks are retained on the film after a caustic wash cycle typically used in PET reclaiming processes. Ex. 1001, 6:61–65. The ’422 Patent further states that labels are fully recyclable if the polymers used are clear, preferably clear PET, and the labels include inks that can be washed off in a “typical PET recycling wash (caustic wash).” Id. at 11:44– 49; see also id. at 11:49–54 (describing embodiments in which the labels are free or substantially free of inks that cannot be washed off in a caustic wash or where the labels are free or substantially free of color plastics that cannot be recycled). The ’422 Patent further discusses “industry standards” for determining whether various embodiments of shrink labels are recyclable. See, e.g., id. at 11:29–53. For example, the Specification states that the “Association for Plastic Recyclers (APR) Critical Guidance Protocol for Clear PET Articles with Labels and Closures (PET-CG-02)” (Ex. 1005) can certify that a film is fully recyclable with a container or bottle. Id. at 11:34– 38. Additionally, the Specification states that labels “are recyclable according to the Evaluation of the Near Infrared (NIR) Sorting Potential of a Whole Plastic Article (SORT-B-01)” (Ex. 1010) and/or the “Evaluation of Sorting Potential for Plastic Articles Utilizing Metal, Metalized, or Metallic Printed Components (SORT-B-03)” (Ex. 1011). Ex. 1001, 11:39–44. The ’422 Patent further states that embodiments of the labels “are fully recyclable. For example, the labels may include inks that can be washed off in a typical PET recycling wash (caustic wash) and the polymers” are preferably clear PET. Id. at 11:44–48. The ’422 Patent thus provides various descriptions or standards to determine the recyclability of shrink labels. For the purposes of addressing the anticipation and obviousness grounds, we determine that any of these standards can be used to determine if a shrink label is “recyclable.” We note that our construction is preliminary and is based on the present record. We invite the parties to further the address the construction of “wherein the recyclable shrink label is recyclable with a PET container” during trial.” slip op. at 12
Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · NautilusPatents in suitUS 11,961,422 - Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing deniedPTAB · Sep 15, 2025 · IPR2025-00005 · APJ John G New · IPR · Rehearing
Denied Solus’s rehearing request; the Board maintained its denial of institution because the petition did not show a reasonable likelihood of prevailing on the challenged claims.
RulingsRehearing decision- RehearingRehearing, deniedDenied
“of the decision de novo, but instead review the decision for an abuse of discretion. 37 C.F.R. § 42.71(c). An abuse of discretion may be determined “if a decision is based on an erroneous interpretation of law, if a factual finding is not supported by substantial evidence, or if the decision represents an unreasonable judgment in weighing relevant factors.” Arnold” slip op. at 2
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable
“[O]f the 44 specimens tested by Ye, as revealed in Ye’s Table II, only a single specimen, specimen 15, meets the required TC ratios recited in challenged claim 1 of the ’541 patent. Furthermore, none of the references cited by Petitioner teach, or even remotely suggest, the four requisite TC ratios recited by challenged claim 1. We find Petitioner’s argument that a person of ordinary skill in the art would have been motivated to exclusively select Ye’s sample 15, out of the remaining 43, to which to apply the teachings of Hara and Otsuka concerning the requisite tensile strength and weight deviation ranges in the hope of arriving at the claimed invention, is implausible. Indeed, only the ’541 patent, among all of the evidence of record, that actually mentions the required texture coefficient ratios recited in challenged claim 1. Petitioner provides no convincing argument as to why a skilled artisan would have selected sample 15 for combination with Hara and Otsuka.” slip op. at 10
- Expert testimonyPetitioner expert discountedDecided for patent owner
“At the heart of this flaw is Petitioner’s argument, and Dr. Josefowicz’s opinion, that it would have been conventional in the art at the time of filing to vary the electrolyte concentration, electrolysis plating parameters, temperature, and the use of organic and inorganic additives, in order to obtain a copper foil with tensile strength and elongation values falling within the claimed ranges as these ranges were well known, at least since 1974. Ex. 1003 ¶ 63. This statement is largely unsupported by evidence of record, with the sole exception of Table 2 of Lowenheim, which, as Patent Owner points out, provides tensile strengths well outside the claimed range. Petitioner provides insufficient guidance as to how a person of ordinary skill in the art would have known which parameters to vary, or how to vary them, to provide the foil of Hirose with a tensile strength or weight deviation within the claimed range. Dr. Josefowicz’s statement that this would result from routine optimization, and was “conventional” may or may not be true, but it is insufficiently supported by evidence of record to be persuasive.” slip op. at 6
§ 103 obviousnessPatents in suitUS 9,457,541 - Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing deniedPTAB · Sep 15, 2025 · IPR2025-00005 · APJ John G New · IPR · Rehearing
The Board denied rehearing and left in place its denial of institution because Petitioner did not show a reasonable likelihood of prevailing on claims 1-4.
RulingsRehearing decision- RehearingRehearing, deniedDenied
“In summary, we again conclude that Petitioner has failed to provide sufficient evidence to demonstrate that a person of ordinary skill in the art would have had a reasonable expectation of success in combining the cited prior art references, in combination with Dr. Josefowicz’s relatively unsupported testimony concerning a skilled artisan’s ability to optimize various constituents and conditions, to arrive at the claimed invention. Petitioner has not pointed to any argument or unconsidered evidence of record that is sufficient to show that, in reaching its conclusion, the Board abused its discretion by basing its Decision on an erroneous interpretation of law, a factual finding not supported by substantial evidence, or an unreasonable judgment in weighing relevant factors. Arnold, 362 F.3d at 1340.” slip op. at 8
- Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable
“teaches the tensile strengths of various types of copper-electroplated steel electrical cable wire of different properties, including high strength, hardness, low electrical resistivity, near zero strength, good leveling, and thermal stability, some of which fall within the claimed range of tensile strength of 30 to 40 kgf/mm2. Lowenheim, 196, Table II. However, none of these categories correspond to those copper foil properties recited in the claims, and Dr. Josefowicz’s testimony provides little guidance as to how a person of ordinary skill in the art would have known how to optimize the recited properties, and particularly so in combination with the teachings of Hirose and the other cited prior art references. Furthermore, as we noted in our Decision:” slip op. at 7
- Expert testimonyPetitioner expert discountedDecided for patent owner
“At the heart of this flaw is Petitioner’s argument, and Dr. Josefowicz’s opinion, that it would have been conventional in the art at the time of filing to vary the electrolyte concentration, electrolysis plating parameters, temperature, and the use of organic and inorganic additives, in order to obtain a copper foil with tensile strength and elongation values falling within the claimed ranges as these ranges were well known, at least since 1974. Ex. 1003 ¶ 63. This statement is largely unsupported by evidence of record, with the sole exception of Table 2 of Lowenheim, which, as Patent Owner points out, provides tensile strengths well outside the claimed range. Petitioner provides insufficient guidance as to how a person of ordinary skill in the art would have known which parameters to vary, or how to vary them, to provide the foil of Hirose with a tensile strength or weight deviation within the claimed range. Dr. Josefowicz’s statement that this would result from routine optimization, and was “conventional” may or may not be true, but it is insufficiently supported by evidence of record to be persuasive. Id. (emphasis added) (footnote omitted).” slip op. at 6
§ 103 obviousnessPatents in suitUS 9,457,541 - Zhuhai Cosmx Battery Co., Ltd. v. Ninge Amperex Technology LimitedInstitution deniedPTAB · Aug 20, 2025 · IPR2025-00385 · APJ Debra L Dennett · IPR · Institution
The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–10 were anticipated by Nishikawa or obvious over the asserted combinations.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied
“review under 35 U.S.C. § 314 (2018); 37 C.F.R. § 42.4(a). The standard for instituting an inter partes review is set forth in 35 U.S.C. § 314(a), which provides that an inter partes review may not be instituted “unless the Director determines . . . there is a reasonable likelihood that the petitioner would prevail with respect to at least [one] of the claims challenged in the petition.” For the reasons set forth below, upon considering the Petition and Preliminary Response, we determine that Petitioner has not established a reasonable likelihood of prevailing with respect to at least one challenged claim. Accordingly, we deny the Petition and decline to institute an inter partes review.” slip op. at 2
- Skill levelSkill level petitioner adoptedOther
“Petitioner contends that A person of ordinary skill in the relevant art would typically hold an advanced degree in chemistry, material science, and/or a related discipline, and have at least two years of experience with designing and/or fabricating battery separators or have an equivalent level of education, training, and experience. Pet. 5. Patent Owner “adopts the definition proposed by Petitioner” for the purposes of the Preliminary Response. Prelim. Resp. 22. In light of the record before us, and for purposes of this Decision, we adopt Petitioner’s unopposed definition because it is consistent with the specification. We note that neither party indicated that the result would change under any different definition.” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Absolute plastic deformation rate” and “relative plastic deformation rate” are the only claim terms disputed in this proceeding, and are clearly defined in the Specification and in claim 1. See Spec. 4:22–27, 4:47–54; 25:31–37. Because we determine that claim construction is not necessary to decide whether to institute, we do not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review). slip op. at 11
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable
“Petitioner’s arguments are unconvincing. Petitioner points to nothing in Nishikawa that allows a POSITA to determine L2 (defined as “a length of 4 Tensile strength is measured as force per units area, such as MPa or psi. One MPa equals one N/mm2. Nishikawa Table 1 discloses tensile strength in N/cm. Ex. 1004 Table 1. Petitioner makes calculations to convert the reported N/cm into N/m2 and then to GPa, but provides no explanation for why tensile strength is reported in N/cm or how it was measured. See Pet. 31. the porous substrate after the porous substrate is stretched to breakage and docked along the fracture caused by the breakage and flattened”) or L2 – L0. See generally Pet., Ex. 1004. Petitioner and its expert, Dr. Pecht, fail to adequately explain why tensile strength divided by Young’s modulus is “a proxy for L1 – L2” or why such a proxy is sufficient to disclose the limitation as stated. Instead, we are required to rely on “approximations” and “estimates” with insufficient explanation of why such they are appropriate or adequate. See Pet. 26, 30, 32; see also Ex. 1003 ¶¶ 97, 105–108, 111.” slip op. at 13
Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,964,927 - Luminex International Co., Ltd. / Menard, Inc. v. Signify Holdings B.V.Some claims unpatentablePTAB · Aug 13, 2025 · IPR2024-01469 · APJ Steven M Amundson · IPR · Final written decision
Claims 1–7, 9–15, and 18–20 are unpatentable; claims 8, 16, and 17 are not determined unpatentable under the asserted prior-art grounds.
RulingsFinal written decision- PTAB / AIA Trials › §315(b) time barNot time barredDecided for petitioner
“G. Analysis 1. REAL PARTY IN INTEREST Based on the record before us and for the reasons explained below, we disagree with Patent Owner that Menard is a “real party in interest” under § 315(b). See Resp. 77–82; Sur-reply 27–28. First, the circumstances here differ materially from the circumstances in Ventex. There, two agreements defined the relationship between Ventex (the petitioner and manufacturer of Heatwave fabric) and Seirus (the alleged real party in interest and purchaser of Heatwave fabric). Ventex, IPR2017- 00651, Paper 152 at 7 & n.8. First, a 2013 Supplier Agreement “prevented Ventex from selling to Seirus competitors” and included an indemnity provision requiring Ventex to indemnify Seirus for losses arising from Ventex’s failure to perform certain obligations. Id. at 7, 14. Second, a 2016 Exclusive Manufacturing Agreement provided that Ventex would manufacture the Heatwave fabric only for Seirus in exchange for Seirus’s payment of an exclusivity fee. Id. at 7. Columbia (the patent owner) accused Seirus products incorporating the Heatwave fabric of infringing the patent at issue, and Columbia served Seirus with a complaint alleging patent infringement in 2014 more than two years before Ventex filed a petition in 2017. Id. at 5, 7. When determining that Seirus was a “real party in interest” under § 315(b), the Board reasoned that “Ventex and Seirus had a specially structured, preexisting, and well established business relationship with one another, including indemnification and exclusivity arrangements.” Ventex, IPR2017-00651, Paper 152 at 10; see id. at 12. Additionally, the Board noted that certain evidence “suggest[ed] that” slip op. at 32
- PTAB / AIA Trials › Real party in interest / privityRpi dispute resolved for petitionerDecided for petitioner
“G. Analysis 1. REAL PARTY IN INTEREST Based on the record before us and for the reasons explained below, we disagree with Patent Owner that Menard is a “real party in interest” under § 315(b). See Resp. 77–82; Sur-reply 27–28. First, the circumstances here differ materially from the circumstances in Ventex. There, two agreements defined the relationship between Ventex (the petitioner and manufacturer of Heatwave fabric) and Seirus (the alleged real party in interest and purchaser of Heatwave fabric). Ventex, IPR2017- 00651, Paper 152 at 7 & n.8. First, a 2013 Supplier Agreement “prevented Ventex from selling to Seirus competitors” and included an indemnity provision requiring Ventex to indemnify Seirus for losses arising from Ventex’s failure to perform certain obligations. Id. at 7, 14. Second, a 2016 Exclusive Manufacturing Agreement provided that Ventex would manufacture the Heatwave fabric only for Seirus in exchange for Seirus’s payment of an exclusivity fee. Id. at 7. Columbia (the patent owner) accused Seirus products incorporating the Heatwave fabric of infringing the patent at issue, and Columbia served Seirus with a complaint alleging patent infringement in 2014 more than two years before Ventex filed a petition in 2017. Id. at 5, 7. When determining that Seirus was a “real party in interest” under § 315(b), the Board reasoned that “Ventex and Seirus had a specially structured, preexisting, and well established business relationship with one another, including indemnification and exclusivity arrangements.” Ventex, IPR2017-00651, Paper 152 at 10; see id. at 12. Additionally, the Board noted that certain evidence “suggest[ed] that” slip op. at 32
- Skill levelOther
“C. Level of Ordinary Skill in the Art Factors pertinent to determining the level of ordinary skill in the art include (1) the educational level of the inventor; (2) the type of problems encountered in the art; (3) prior-art solutions to those problems; (4) the rapidity with which innovations are made; (5) the sophistication of the technology; and (6) the educational level of workers active in the field. Envtl. Designs, Ltd. v. Union Oil Co., 713 F.2d 693, 696–97 (Fed. Cir. 1983). Not all factors may exist in every case, and one or more of these or other factors may predominate in a particular case. Id. These factors are not exhaustive, but merely a guide to determining the level of ordinary skill in the art. Daiichi Sankyo Co. v. Apotex, Inc., 501 F.3d 1254, 1256 (Fed. Cir. 2007). Moreover, the prior art itself may reflect an appropriate skill level. Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001). Petitioner asserts that a person of ordinary skill in the art at the ’336 patent’s effective filing date would have had “a bachelor’s degree in mechanical engineering, electrical engineering, optics, or physics with at least three years of experience working in the design of LED lights or lighting fixtures; a master’s degree in one of the above disciplines with at least two years of experience; or equivalent experience.” Pet. 14 (citing Ex. 1004 ¶¶ 26–29). Dr. Eden’s testimony supports Petitioner’s assertion. See Ex. 1004 ¶¶ 27–28. Patent Owner “adopts for purposes of this proceeding only” Petitioner’s description of an ordinarily skilled artisan. Resp. 10 (citing Pet. 14). We adopt Petitioner’s description of an ordinarily skilled artisan because it comports with the technology and claims of the ’336 patent as” slip op. at 40
- Obviousness (§103) › Objective indicia / secondary considerationsObjective indicia no nexusDecided for petitioner
“Alleged Objective Indicia of Nonobviousness (i) General Principles Before reaching a conclusion about obviousness, we consider evidence concerning objective indicia of nonobviousness. See Apple, 839 F.3d at 1048. For such evidence to have substantial weight, “its proponent must establish a nexus between the evidence and the merits of the claimed invention.” ClassCo, Inc. v. Apple, Inc., 838 F.3d 1214, 1220 (Fed. Cir. 2016); see Ancora Techs., Inc. v. Roku, Inc., 140 F.4th 1351, 1361 (Fed. Cir. 2025) (noting that the Board did not err by requiring “a nexus to the challenged claims as opposed to the patent as a whole”). “[T]here is no nexus unless the evidence presented is ‘reasonably commensurate with the scope of the claims.’” ClassCo, 838 F.3d at 1220 (quoting Rambus Inc. v. Rea, 731 F.3d 1248, 1257 (Fed. Cir. 2013)). The patentee “bears the burden of showing that a nexus exists.” WMS Gaming, Inc. v. Int’l Game Tech., 184 F.3d 1339, 1359 (Fed. Cir. 1999). A rebuttable presumption of nexus arises “when the patentee shows that the asserted objective evidence is tied to a specific product and that product ‘embodies the claimed features, and is coextensive with them.’” Fox Factory, Inc. v. SRAM, LLC, 944 F.3d 1366, 1373 (Fed. Cir. 2019) (quoting Polaris Indus., Inc. v. Arctic Cat, Inc., 882 F.3d 1056, 1072 (Fed. Cir. 2018)). Whether a rebuttable presumption of nexus arises “turns on the nature of the claims and the specific facts.” Teva Pharms. Int’l GmbH v. Eli Lilly & Co., 8 F.4th 1349, 1362 (Fed. Cir. 2021). The presumption analysis should consider the unclaimed features in the product tied to the objective evidence to assess their significance and impact on the correspondence between the patented invention and the product. Quanergy Sys., Inc. v. Velodyne Lidar USA, Inc., 24 F.4th 1406, 1418 (Fed. Cir. 2022). When, “for example, the patented invention is only a small component of the product tied to the objective evidence, there is no presumption of nexus.” Henny Penny Corp. v. Frymaster LLC, 938 F.3d 1324, 1333 (Fed. Cir. 2019). Absent a presumption of nexus, the patentee may prove nexus by” slip op. at 76
Patent outcomesUS 10,299,336 mixed§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,299,336 - Luminex International Co., Ltd. / Menard, Inc. v. Signify Holdings B.V.Some claims unpatentablePTAB · Aug 13, 2025 · IPR2024-00101 · APJ Steven M Amundson · IPR · Final written decision
Claims 1–7, 9–15, and 18–20 are unpatentable; claims 8, 16, and 17 are not shown unpatentable under the asserted grounds.
RulingsFinal written decision- PTAB / AIA Trials › Real party in interest / privityRpi dispute resolved for patent ownerDecided for patent owner
“G. Analysis 1. REAL PARTY IN INTEREST Based on the record before us and for the reasons explained below, we” slip op. at 32
- PTAB / AIA Trials › §315(b) time barDecided for patent owner
“III. WHETHER THE PETITION IS TIME BARRED The parties dispute whether the Petition is time barred based on a” slip op. at 18
- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“vacated the panel’s decision denying institution. Paper 12, 6. Among other things, the Director determined based on a “review of the current record” that (1) Menard is not a real party in interest in this proceeding and (2) Menard is not a privy of Petitioner. Id. at 5. Further, the Director remanded the case to the panel and instructed the panel “to determine whether the Petition presents a reasonable likelihood of prevailing with respect to at least one of the challenged claims under 35 U.S.C. § 314(a), and to determine whether to institute inter partes review accordingly.” Id. at 5–6.” slip op. at 3
- BurdenMixed
“U.S. Patent No. 10,299,336 B2 (“the ’336 patent”) (Exhibit 1001). For the reasons explained below, a preponderance of the evidence shows that claims 1–7, 9–15, and 18–20 in the ’336 patent are unpatentable and does not show that claims 8, 16, and 17 are unpatentable. See 35 U.S.C. § 316(e) (2024).” slip op. at 2
Patent outcomesUS 10,299,336 mixed§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,299,336 - PTAB · Jul 10, 2025 · IPR2025-00175 · APJ Jo-Anne M Kokoski · IPR · Institution
The Board instituted review of claims 1–17 on all asserted grounds, finding a reasonable likelihood of unpatentability on at least one challenged claim.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“Institution of an inter partes review is authorized by statute when “the information presented in the petition . . . and any response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314 (2018); see also 37 C.F.R. § 42.4 (2023). For the reasons discussed below, we determine that Petitioner establishes a reasonable likelihood of prevailing with respect to the patentability of at least one claim of the ’562 patent. Accordingly, we institute an inter partes review of claims 1–17 of the ’562 patent.” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“(“POSITA”) would have had “at least a four-year degree in electrical engineering or a closely related field, and at least two years of experience in semiconductor device design,” and “[a]dditional education could substitute for professional experience and vice versa.” Pet. 6 (citing Ex. 1002 ¶¶ 80–” slip op. at 6
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached
“customary meaning of such claim as understood by one of ordinary skill in the art and the prosecution history pertaining to the patent.” 37 C.F.R. § 42.100(b). Under this standard, claim terms are generally given their plain and ordinary meaning as would have been understood by a person of ordinary skill in the art at the time of the invention and in the context of the entire patent disclosure. Phillips v. AWH Corp., 415 F.3d 1303, 1313 (Fed. Cir. 2005) (en banc). Only those terms in controversy need to be construed, and only to the extent necessary to resolve the controversy. Realtime Data LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019). Neither party proposes any explicit construction of any term. See Pet. 7 (“For the purposes of this IPR, the plain meaning of each term can be applied.”). We do not expressly construe any term for purposes of this Decision.” slip op. at 7
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Instituted
“On this record, we are persuaded that Petitioner adequately establishes that Usui discloses all of the limitations of claim 1. Usui discloses that aluminum or aluminum alloy layer 15 is in electrical contact with titanium underlayer 13, and titanium nitride layer 14 is located “intermediate the [titanium underlayer] 13 and the aluminum or aluminum alloy layer 15” to prevent “reaction between the aluminum layer 15 and underlayer 13.” Ex. 1004, 3:27–29, 3:38–41, 3:58–63. Usui further discloses that “a capping layer is provided above layer 15,” and that “[p]referred capping layers are titanium nitride and combinations of as layer 18 of a group IVA metal, preferably titanium with a titanium nitride layer 19.” Id. at 3:67–4:6. Usui teaches that titanium nitride layer 19 is about 150 to 800 Å thick, and that the thickness of titanium underlayer 13 is between about 90 to 110 Å. Id. at 3:31–33, 4:6–8. Usui also teaches that the interconnect metallurgy structures described therein “exhibit[] enhanced electromigration characteristics” and “are especially useful for forming electrical connections or wiring such as between active and/or passive devices of an integrated circuit structure.” Id. at 1:8–14. Usui’s description of a plurality of metal layers (layers 13–18) and a capping layer formed over the plurality of metal layers (layer 19), along with its description of the structure’s usefulness for forming electrical connections in an integrated circuit structure, is sufficient, on this record, to establish that Usui discloses “an electrode stack including a plurality of metal layers and a capping layer formed over said plurality of metal layers” as recited in claim 1. Usui’s teaching that the capping layer is a refractory metal nitride (titanium nitride) that has a thickness (150–800 Å) greater than the bottommost layer of the plurality of metal layers (layer 13, 90–110 Å), sufficiently establishes, on this record, that Usui discloses the “said capping layer consisting only of a refractory metal nitride, said refractory metal nitride forming a top of said electrical contact and having a thickness greater than that of a bottommost layer of said plurality of metal layers” limitation of claim 1.” slip op. at 11
Claim construction§ 102 anticipation§ 103 obviousnesscites PhillipsPatents in suitUS 8,686,562 - PTAB · Jul 9, 2025 · IPR2025-00094 · APJ Christopher M Kaiser · IPR · Institution
The Board instituted IPR on claims 1–16 and all asserted grounds, finding a reasonable likelihood that claim 1 is obvious over Bonn and Mizuta.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“At this preliminary stage, we determine whether the information presented shows a reasonable likelihood that Petitioner would prevail in establishing that at least one of the challenged claims would have been unpatentable over the proposed prior art. We analyze the asserted grounds with the above-noted principles in mind.” slip op. at 7
- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that one of ordinary skill in the art “would have possessed at least a four-year degree in electrical engineering or a closely related field, and at least two years of experience in semiconductor device design.” Pet. 5 (citing Ex. 1003 ¶¶ 67–69). Petitioner also argues that “[a]dditional education could substitute for professional experience and vice versa.” Id. On the present record, Patent Owner does not dispute Petitioner’s proposed level of ordinary skill. Prelim. Resp. 1–52. Neither party explains why the outcome of this case would be affected by the adoption of any of the proffered definitions of a person of ordinary skill in the art. For purposes of this Decision, we adopt Petitioner’s assessment of the level of ordinary skill in the art, as it appears to be consistent with the ’003 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“We apply the same claim-construction standard used in the federal courts—in other words, the claim-construction standard that would be used to construe the claim in a civil action under 35 U.S.C. § 282(b), which is articulated in Phillips. See 37 C.F.R. § 42.100(b). Under the Phillips standard, the “words of a claim ‘are generally given their ordinary and customary meaning,’” which “is the meaning that the term would have to a person of ordinary skill in the art in question at the time of the invention, i.e., as of the effective filing date of the patent application.” Phillips, 415 F.3d at 1312–13. Neither party proposes construing any claim terms. Pet. 6; Prelim. Resp. 1–52. On the present record, we agree. As discussed below, we are able to determine whether to institute inter partes review of the ’003 patent without expressly construing any terms. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 9
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundInstituted
“Patent Owner argues that Petitioner does not show sufficiently that a person of ordinary skill in the art would have had a reason to modify Bonn to remove local oscillator 55. Prelim. Resp. 13–15. We disagree. Petitioner argues that, “[i]n addition to using Figure 7’s ‘dual gate FET structure in high frequency signal mixing’ applications . . . , Bonn discloses using this dual gate FET in ‘other applications such as high frequency signal amplification.’” Pet. 22 (quoting Ex. 1006, 11:26–37). Indeed, Bonn does suggest using its structure for signal amplification. Ex. 1006, 11:26–37 (“the dual gate FET structure of the present invention can be tailored to provide superior performance . . . in . . . other applications such as high frequency signal amplification”). On the present record, this appears to have provided the motivation for a person of ordinary skill in the art to use Bonn for amplification instead of for signal mixing. Petitioner relies on the testimony of Dr. Bernstein to show the modifications that a person of ordinary skill in the art would have considered necessary in order to convert Bonn’s structure for signal-amplification use. Pet. 23–25 (citing Ex. 1003 ¶¶ 98–109). In particular, Petitioner cites Dr. Bernstein’s testimony that a person of ordinary skill in the art “would have found it obvious to remove Figure 1’s LO (local oscillator) port 55 and its associated impedance matching components because the LO signal is no longer being mixed.” Ex. 1003 ¶ 98; see Pet. 23. Dr. Bernstein supports this testimony with citations to Bonn and with reasoning regarding why a person of ordinary skill in the art would have made this modification. Ex. 1003 ¶ 98 (citing Ex. 1006, 1:20–23, 3:19–21, 3:30–41). Accordingly, on the present record, we are persuaded that Petitioner has shown sufficiently that a person of ordinary skill in the art would have had reason to modify Bonn’s structure to remove the connection between a local oscillator and the gate of the second transistor. Finally, Patent Owner argues that Petitioner’s proposed modification would have rendered Bonn inoperable for its intended purpose because the modification would eliminate the ability of Bonn’s structure to conduct high frequency signal mixing. Prelim. Resp. 26–27. As Patent Owner notes, one purpose of Bonn is to mix high-frequency signals. Ex. 1006, 11:33–36. But Bonn itself teaches using its structure for “other applications,” including “high frequency signal amplification.” Id. at 11:33–37. Thus, on the present record, we are persuaded that Petitioner’s proposed modification does not render Bonn inoperable for its intended purpose so much as it acknowledges the modifications necessary to convert Bonn from one of its intended purposes to another. Thus, Petitioner has shown sufficiently for the purpose of the present Decision that a person of ordinary skill in the art would have had reason to combine Bonn and Mizuta and that the combination of Bonn and Mizuta teaches or suggests the disputed limitation of claim 1. We encourage the parties to develop the arguments and the record surrounding this issue further during the trial.” slip op. at 14
Claim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 8,264,003
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.