- Innoscience America, Inc. v. Infineon Technologies Americas Corp.No claims unpatentablePTAB · Jun 30, 2026 · IPR2025-00175 · APJ Jo-Anne M Kokoski · IPR · Final written decision
Claims 1–17 were not shown unpatentable because Petitioner failed to establish that Usui’s interconnect structure or Yu’s metal gate stacks satisfy the construed “electrode stack” limitation.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“(“POSITA” or “POSA”) would have had “at least a four-year degree in electrical engineering or a closely related field, and at least two years of experience in semiconductor device design,” and “[a]dditional education could substitute for professional experience and vice versa.” Pet. 6 (citing Ex. 1002 ¶¶ 80–82). Patent Owner does not dispute Petitioner’s proposed level of ordinary skill. PO Resp. 1–76. Neither party explains why the outcome of this case would be affected by the adoption of the proffered definition of a person of ordinary skill in the art. In the Institution Decision, we adopted the assessment offered by Petitioner. Dec. 6–7. Because Petitioner’s definition of the level of skill in the art is consistent with the ’562 patent and the asserted prior art, we maintain Petitioner’s definition for purposes of this Final Written Decision. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir 2001).” slip op. at 9
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner
“comprises the recited metals and has the recited thickness, which forms an electrical contact for use on a semiconductor device generally or a group III- V semiconductor in particular. This is consistent with our determination that “electrode stack” is a conductor that provides a path for current entering or leaving a medium such as a semiconductor device We disagree with Patent Owner that “electrode stack” as used in the challenged claims should be limited to the specific electrodes shown in the embodiments described in the Specification. See PO Resp. 4–9. Although the Specification describes embodiments using source, drain, and Schottky gate electrodes as electrical contacts, we see no reason to construe the term “electrode stack” itself to be limited to these components as Patent Owner proposes. Claims 1 and 13 expressly recite that electrode stacks comprise the claimed “electrical contact,” without expressly including or precluding any specific type of electrode. Ex. 1001, 5:54–63, 6:37–47. The Federal Circuit advises that the Specification “is not a substitute for, nor can it be used to rewrite, the chosen claim language. ‘Specifications teach. Claims claim.’” SuperGuide, 358 F.3d at 875 (quoting SRI Int’l v. Matsushita Elec. Corp. of Am., 775 F.2d 1107, 1121 n.14 (Fed. Cir. 1985) (en banc)). The Specification does teach electrical contacts that include source, drain, and Schottky gate electrodes, but claims 1 and 13 are directed to electrical contacts that are not expressly so limited. Patent Owner’s proposed construction would effectively rewrite the claim by adding limitations, which we decline to do under the guise of claim construction. See id. (“Though understanding the claim language may be aided by the explanations contained in the written description, it is important not to import into a claim limitations that are not a part of the claim.”). In view of the foregoing, we construe the claim term “electrode stack” to mean “a conductor that provides a path for current entering or leaving a medium such as a semiconductor device.”” slip op. at 17
- Expert testimonyPetitioner expert discountedDecided for patent owner
“that the identified layers in Usui’s interconnect metallurgy structure form an “electrode stack including a plurality of metal layers and a capping layer formed over said plurality of metal layers” as recited in claim 1. See Pet. 11–12 (citing Ex. 1002 ¶¶ 89–91). Neither Petitioner nor Dr. Zhao, however, provide adequate explanation or evidence as to why Usui’s interconnect metallurgy structure forms an “electrode stack,” i.e., a conductor that provides a path for current entering or leaving a medium such as a semiconductor device. Dr. Zhao’s testimony merely repeats the disclosures in Usui and concludes, without further technical detail, explanation, or reference to objective evidence, that Usui’s Figure 8 discloses an electrode stack. Ex. 1002 ¶¶ 89–91. Dr. Zhao’s testimony sets forth Petitioner’s conclusory assertions as though they are facts, rather than setting forth facts and evidence in support of those assertions. Compare id. with Pet. 11–12. Absent underlying facts or evidence to support Dr. Zhao’s opinion, the cited testimony “adds little to the conclusory assertion for which it is offered to support, and is entitled to little weight.” Xerox Corp. v. Bytemark, Inc., IPR2022-00624, Paper 9 at 15 (PTAB Aug. 24, 2022) (precedential). In contrast, Patent Owner’s declarant Dr. Piner testifies, with evidentiary support, that interconnects (such as Usui’s interconnect metallurgy structure) and electrical contacts (such as that claimed in the ’562 patent) are not the same thing. See Ex. 2024 ¶¶ 63–70. For example, Dr. Piner explains: In other words, not all metals in a semiconductor device have the same purpose and could not be said to be interchangeable. By August 2009 it was well known to a POSA how to discern if a metal component in a transistor is an interconnect or serves as an electrical contact such as a gate contact or ohmic contact, based on the structure and functionality of the metal component. For example, interconnects are made up of metal strips and are deposited on insulators. EX-1011 (Mishra) at 216. Interconnects are low resistance conductors that can carry very high current densities. Id., 216, 217. Unlike Schottky contacts and ohmic contacts, interconnects do not provide non-linear IV response like Schottky contacts nor inject electrons and holes into semiconductors like ohmic contacts. Id., 218. As many of the references cited by Dr. Zhao illustrate, electrical contacts had their own highly complex design challenges. EX-1008 (Pearton), 41-59 (Pages 53-71 of 383) (discussing electrical contacts); EX-1017 (Kramer), 11-126 (Pages 18-130 of 151) (same). And while Dr. Zhao cites these as supporting a POSA’s knowledge of an electrical contact, none of these references describe electrical contacts as interconnects. Id. ¶ 71. Dr. Piner further testifies that Usui’s interconnect metallurgy structure is an interconnect, and not an electrical contact, because “Usui states that ‘[t]he structures fabricated by the process of the present invention are especially useful for forming electrical connections or wiring such as between active and/or passive devices of an integrated circuit structure.’” Id. ¶ 148 (citing Ex. 1004, 1:11–14) (alteration in original); see also id. ¶¶ 150– 151 (Dr. Piner testifying that Usui’s interconnect metallization structure is not an “electrode stack” under a broad definition of electrode). Dr. Piner’s testimony in this regard rebuts Petitioner’s and Dr. Zhao’s conclusory assertions to the contrary.” slip op. at 21
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable
“conductor that provides a path for current entering or leaving a medium such as a semiconductor device.” Thus, Petitioner must show that Usui’s layers 13–15, 18, and 19 provide a path for current entering or leaving a medium such as a semiconductor device. After reviewing the complete trial record, we are not persuaded that Petitioner has done so. Petitioner relies on the testimony of Dr. Zhao to support its contention that the identified layers in Usui’s interconnect metallurgy structure form an “electrode stack including a plurality of metal layers and a capping layer formed over said plurality of metal layers” as recited in claim 1. See Pet. 11–12 (citing Ex. 1002 ¶¶ 89–91). Neither Petitioner nor Dr. Zhao, however, provide adequate explanation or evidence as to why Usui’s interconnect metallurgy structure forms an “electrode stack,” i.e., a conductor that provides a path for current entering or leaving a medium such as a semiconductor device. Dr. Zhao’s testimony merely repeats the disclosures in Usui and concludes, without further technical detail, explanation, or reference to objective evidence, that Usui’s Figure 8 discloses an electrode stack. Ex. 1002 ¶¶ 89–91. Dr. Zhao’s testimony sets forth Petitioner’s conclusory assertions as though they are facts, rather than setting forth facts and evidence in support of those assertions. Compare id. with Pet. 11–12. Absent underlying facts or evidence to support Dr. Zhao’s opinion, the cited testimony “adds little to the conclusory assertion for which it is offered to support, and is entitled to little weight.” Xerox Corp. v. Bytemark, Inc., IPR2022-00624, Paper 9 at 15 (PTAB Aug. 24, 2022) (precedential).” slip op. at 21
Patent outcomesUS 8,686,562 not shown unpatentableClaim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 8,686,562 - Innoscience America, Inc. v. Infineon Technologies Americas Corp.No claims unpatentablePTAB · Jun 12, 2026 · IPR2025-00094 · APJ Christopher M Kaiser · IPR · Final written decision
Claims 1–16 were not shown unpatentable under any asserted obviousness ground because Petitioner failed to establish the proposed modifications and combinations.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that one of ordinary skill in the art “would have possessed at least a four-year degree in electrical engineering or a closely related field, and at least two years of experience in semiconductor device design.” Pet. 5 (citing Ex. 1003 ¶¶ 67–69). Petitioner also argues that “[a]dditional education could substitute for professional experience and vice versa.” Id. Patent Owner does not dispute Petitioner’s proposed level of ordinary skill. PO Resp. 1–76. Neither party explains why the outcome of this case would be affected by the adoption of the proffered definition of a person of ordinary skill in the art. Accordingly, and because it appears to be consistent with the ’003 patent and the asserted prior art, we adopt Petitioner’s assessment of the level of ordinary skill in the art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 7
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Neither party proposes construing any claim terms. Pet. 6; Prelim. Resp. 1–76. In addition, as discussed below, we are able to determine the outcome of this proceeding without expressly construing any terms. Thus, we do not construe any terms for the purposes of this Decision. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 8
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable
“challenged claim. Unigene Labs., Inc. v. Apotex, Inc., 655 F.3d 1352, 1360 (Fed. Cir. 2011). “This is so because inventions in most, if not all, instances rely upon building blocks long since uncovered, and claimed discoveries almost of necessity will be combinations of what, in some sense, is already known.” KSR, 550 U.S. at 418–419. On the other hand, an obviousness analysis “need not seek out precise teachings directed to the specific subject matter of the challenged claim, for a court can take account of the inferences and creative steps that a person of ordinary skill in the art would employ.” Id. at 418; accord In re Translogic Tech., Inc., 504 F.3d 1249, 1259 (Fed. Cir. 2007). However, a petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” In re Magnum Oil Tools Int’l, Ltd., 829 F.3d 1364, 1380 (Fed. Cir. 2016). Instead, a petitioner must articulate a reason why a person of ordinary skill in the art would have combined or modified the prior art references. In re NuVasive, Inc., 842 F.3d 1376, 1382 (Fed. Cir. 2016); see also Metalcraft of Mayville, Inc. v. The Toro Co., 848 F.3d 1358, 1366 (Fed. Cir. 2017) (“In determining whether there would have been a motivation to combine prior art references to arrive at the claimed invention, it is insufficient to simply conclude the combination would have been obvious without identifying any reason why a person of skill in the art would have made the combination.”); Belden Inc. v. Berk-Tek LLC, 805 F.3d 1064, 1073 (Fed. Cir. 2015) (“[O]bviousness concerns whether a skilled artisan not only could have made but would have been motivated to make the combinations or modifications of prior art to arrive at the claimed invention.”) (citing InTouch Techs., Inc. v. VGO Commc’ns, Inc., 751 F.3d 1327, 1352 (Fed. Cir. 2014)). In arguing for the obviousness of claim 1 over the combination of Bonn and Mizuta, Petitioner argues that a person of ordinary skill in the art would have modified Bonn to perform high-frequency signal amplification. Pet. 19–25. In particular, Petitioner argues that a person of ordinary skill in the art “would have found it obvious to modify the circuit of Figure 1 [of Bonn] and use Figure 7’s structure for high frequency signal amplification in place of mixer 40,” followed by additional modifications to the circuit of Figure 1. Id. at 22–25. These additional modifications include removing LO port 55, removing FET 20 (along with voltage source 80, capacitors 16, 26, and 34, resistor 18, and inductors 22 and 24), removing capacitor 34 and shorting gate structure 324 to ground, and removing resistors 46 and 48 and shorting terminal 51 to ground. Id. According to Petitioner, the motivation for these modifications was that “Bonn . . . teaches using its dual gate structures for signal amplification without signal mixing.” Id. at 22 (citing Ex. 1006, 11:26–37). On the record developed at trial, we disagree. Bonn does, as Petitioner argues, teach that “the dual gate FET structure of the present invention can be tailored to provide superior performance over the prior art dual gate FET structures in high frequency signal mixing as well as other applications such as high frequency signal amplification.” Ex. 1006, 11:33–37. But the tailoring that Bonn refers to relates to changes to the structure of the field-effect transistor itself, not to the circuitry surrounding that transistor. Id. (teaching that the reason that “the dual gate FET structure of the present invention can be tailored” is that “the parameters such as gate width, dopant concentration, and channel depth, under each gate of the dual gate FET are individually adjusted for optimum performance”). Thus, although Bonn might have motivated a person of ordinary skill in the art to have made changes to the dual-gate FET itself, we are not persuaded that it would have motivated the additional changes to the circuit of Bonn’s Figure 1.” slip op. at 11
- Strike new argumentNew argument disregardedDecided for patent owner
“Mishra’s Figure 5 is a second gate in favor of a new position. Petitioner’s new argument is that a person of ordinary skill in the art would have found it obvious to connect the field plate of Mishra’s Figure 5 to the source instead of the gate, converting the field plate into a second gate. Compare Pet. 83 (equating “drain side gate” with “field plate 66, Figure 5”), 86–88 (identifying field plate 66 as a “second gate”), with Reply 21–22 (identifying only the embodiment of Mishra’s Figure 10 as a source-connected field plate), 22–23 (arguing that Mishra teaches that the Figure 5 embodiment “could be arranged as ‘a single transistor with a dual gate structure’”). Although “the introduction of new evidence in the course of the trial is to be expected in inter partes review trial proceedings,” Genzyme Therapeutic Prods. LP v. Biomarin Pharm. Inc., 825 F.3d 1360, 1366 (Fed. Cir. 2016), the shifting of arguments is not, Wasica Fin. GmbH v. Cont’l Auto. Sys., Inc., 853 F.3d 1272, 1286 (Fed. Cir. 2017). Accordingly, Petitioner’s change of arguments here is inappropriate. Moreover, even if we were to consider Petitioner’s inappropriate new argument, we would conclude that Petitioner does not support the argument with sufficient evidence. “Whether [an obviousness ground] is based on combining disclosures from multiple references, combining multiple embodiments from a single reference, or selecting from large lists of elements in a single reference, there must be a motivation to make the combination and a reasonable expectation that such a combination would be successful, otherwise a skilled artisan would not arrive at the claimed combination.” In re Stepan, 868 F.3d 1342, 1346 n.1 (Fed. Cir. 2017). Petitioner’s new argument relies on a person of ordinary skill in the art modifying the Figure 5 embodiment of Mishra to connect the field plate to the source rather than the gate. Reply 21–24. Petitioner does not, however, show that a person of ordinary skill in the art would have had a motivation to make this modification or a reasonable expectation that this combination would be successful. Id. Petitioner argues instead that “[n]o ‘reason’ is needed.” Id. at 24. Thus, Petitioner does not show by a preponderance of the evidence that claim 1 would have been obvious over the combination of Mishra and Ren.” slip op. at 19
Patent outcomesUS 8,264,003 not shown unpatentableClaim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 8,264,003 - Shenzhen Tuozhu Technology Co., Ltd. v. Stratasys, Inc.No claims unpatentablePTAB · Jun 9, 2026 · IPR2025-00321 · APJ Christopher M Kaiser · IPR · Final written decision
The Board held claims 1, 2, 5–7, 9, 16, and 17 not unpatentable because the asserted combinations did not establish the required purge-tower teachings or prior-art status.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that one of ordinary skill in the art “would have had (1) at least a bachelor’s degree in Mechanical Engineering, Computer Engineering, Chemical Engineering, Materials Science, or a related field, and (2) at least two years of research or industry experience in 3D printing or materials used for 3D printing.” Pet. 5 (citing Ex. 1003 ¶¶ 14–16). Petitioner also argues that “[a]dditional experience could substitute for a formal degree or formal training (and vice versa).” Id. Patent Owner proposes a slightly different level of skill, arguing that a person of ordinary skill in the art “would have had a bachelor’s degree in Mechanical Engineering, Computer Engineering, Chemical Engineering, Materials Science, or a comparable field and at least two years of experience related to 3D printing, with additional experience potentially being a substitute for a formal degree or training (and vice versa).” Prelim. Resp. 24. Neither party explains why the outcome of this case would be affected by the adoption of any of the proffered definitions of a person of ordinary skill in the art. We adopt Petitioner’s assessment of the level of ordinary skill in the art, as it appears consistent with the ’324 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 8
- Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownOther
“According to the ’713 patent, “[p]urge tower 24 itself may be . . . recycled or otherwise discarded as desired.” Ex. 1001, 8:27–28. This description provides some support for Patent Owner’s view, because a purge tower too intimately integrated with the part would be difficult or impossible to recycle or discard. This is further supported by the ’713 patent’s statement that “purge tower 24 may be printed at any suitable location on build substrate 44 (i.e., at any location in the x-y build plane not occupied by 3D part 20 or support structure 22).” Id. at 8:30–34. It also is supported by Dr. Hickner’s testimony that the ’713 patent “clearly shows . . . the 24 purge tower separated from the part” and that “the purge tower is a separate physical object.” Ex. 2016, 28:8–10, 64:1–9. On the other hand, there is evidence supporting Petitioner’s view that, as long as the purge tower is generally separate from the part and the support structure, it may still make contact with those portions of the print. As noted above, “purge tower 24 may be printed at any suitable location on build substrate 44 (i.e., at any location in the x-y build plane not occupied by 3D part 20 or support structure 22).” Ex. 1001, 8:30–34. This language does not exclude locations adjacent to or in contact with the part or the support structure. Thus, determine that a “purge tower,” as that term is used in the context of the ’713 patent, may not be an integrated portion of a printed part or support structure but need not be free of all contact with the printed part or support structure.” slip op. at 9
- BurdenNot shown unpatentable
“There is evidence of record to support both Petitioner’s view and Patent Owner’s view. On the record developed at trial, however, we cannot say that the preponderance of the evidence favors Petitioner, who bears the burden of proof. See 35 U.S.C. § 316(e). Accordingly, Petitioner has not shown by a preponderance of the evidence that KISSlicer teaches printing a layer of a purge tower each time the printer switches one extruder to the operating mode. Because proving the obviousness of claims 1 and 16 requires such a showing, Petitioner has not shown by a preponderance of the evidence that claims 1 and 16 would have been obvious over the combination of Priedeman and KISSlicer. 5. Analysis of Remaining Claims Claims 2, 6, 7, 9, and 17 all depend, directly or indirectly, from claim 1 or claim 16. Accordingly, they all include the limitations of either claim 1 or claim 16. Because, as discussed above, Petitioner has not shown that the combination of Priedeman and KISSlicer teaches or suggests all the limitations of claims 1 and 16, Petitioner also has not proven by a preponderance of the evidence that claims 2, 6, 7, 9, and 17 would have been obvious over that combination of references.” slip op. at 21
- Obviousness (§103) › Analogous artAnalogous artOther
“On the record developed at trial, we agree with Petitioner. According to several industry forum posts, people interested in three-dimensional printing located the website where KISSlicer was posted between February 2012 and April 2012. Ex. 1028, 1 (post discussing and directing others to KISSlicer on April 11, 2012); Ex. 1031, 1 (two posts discussing KISSlicer on March 16, 2012, and March 21, 2012); Ex. 1032, 1 (two posts discussing KISSlicer on February 11, 2012, and February 14, 2012). Thus, not only was it possible for people of ordinary skill in the art to locate KISSlicer; people of ordinary skill in the art actually did locate it. Accordingly, Petitioner has shown by a preponderance of the evidence that KISSlicer was publicly accessible.” slip op. at 19
Patent outcomesUS 9,421,713 not shown unpatentableClaim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 9,421,713 - PTAB · Dec 12, 2025 · IPR2025-01116 · APJ Christopher M Kaiser · IPR · Institution
The Board instituted IPR of claims 1–15 on all asserted grounds, finding a reasonable likelihood that claim 1 would have been obvious over Sudre, Lee, and Penven.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“determine whether to institute an inter partes review under 35 U.S.C. § 314 and 37 C.F.R. § 42.4(a). Inter partes review may not be instituted unless “the information presented in the petition filed under [35 U.S.C.] section 311 and any response filed under [35 U.S.C.] section 313 shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a). “When instituting inter partes review, the Board will authorize the review to proceed on all of the challenged claims and on all grounds of unpatentability asserted for each claim.” 37 C.F.R. § 42.108(a) (2023). In other words, a decision to institute under § 314 may not institute on fewer than all claims challenged in the petition. SAS Inst., Inc. v. Iancu, 138 S. Ct. 1348, 1359–60 (2018). In addition, if the Board institutes trial, it will “institute . . . on all grounds in the petition.” PTAB Consolidated Trial Practice Guide, 5–6 (Nov. 2019)1 (“CTPG”); see also PGS Geophysical AS v. Iancu, 891 F.3d 1354, 1360 (Fed. Cir. 2018) (interpreting the statute to require “a simple yes-” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“had at least (1) a Bachelor’s Degree (or higher) in material science, materials engineering, mechanical engineering, textile engineering, or a related field, and (2) a minimum of two years of working experience in textiles engineering, fibers and textiles manufacturing, or a related field.” Pet. 4 (citing Ex. 1003 ¶¶ 21–22). Petitioner also argues that “[a]dditional education could substitute for professional experience, and vice versa.” Id. On the present record, Patent Owner does not contest Petitioner’s proposed level of ordinary skill. Prelim. Resp. 25–26. For purposes of this Decision, we adopt Petitioner’s assessment of the level of ordinary skill in the art, as it appears consistent with the ’566 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 9
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“Both parties argue that no claim terms require express construction at this stage of the proceeding. Pet. 3; Prelim. Resp. 26. On the present record, we agree. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))). To the extent the parties’ arguments regarding unpatentability do address claim construction issues, we address these issues below.” slip op. at 10
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundDecided for petitioner
“articulated a reason why a person of ordinary skill in the art would have combined the teachings of Sudre, Lee, and Penven. Prelim. Resp. 60–63. In particular, Patent Owner argues that a person of ordinary skill in the art “would not have been motivated to look into Penven to modify the teachings of Lee because Lee and Penven disclose substantially different structures.” Id. at 60–61. This argument does not address Petitioner’s proposed reason to combine, which looks to Lee and Penven each to modify Sudre, not to Penven to modify Lee. See Pet. 79–81. In addition, “[c]ombining the teachings of references does not involve an ability to combine their specific structures.” In re Nievelt, 482 F.2d 965, 968 (CCPA 1973). In other words, “[t]he test for obviousness is not whether the features of a secondary reference may be bodily incorporated into the structure of the primary reference . . . . Rather, the test is what the combined teachings of the references would have suggested to those of ordinary skill in the art.” In re Keller, 642 F.2d 413, 425–26 (CCPA 1981). Petitioner provides “some articulated reasoning with some rational underpinning” to combine the teachings of Sudre with those of Lee and Penven. KSR Int’l Co. v. Teleflex Inc., 550 U.S. 398, 418 (2007). In particular, Petitioner directs us to Sudre’s teaching of “a method for manufacturing PMC,” to Sudre’s lack of teaching of “specific parameters, such as warp thread size and spacing” to satisfy the “particular requirements” of its fabric. Pet. 79 (citing Ex. 1003 ¶¶ 248–250; Ex. 1004, 1:2–5, 6:14–17). As Petitioner points out, id. at 79–80, Lee and Penven provided yarn diameters and loop diameters that were conventional, and there is evidence of record that a person of ordinary skill in the art would have used these conventional diameters in constructing Sudre’s paper machine clothing. Ex. 1003 ¶¶ 258–261, 263–266; Ex. 1006, 3:64–66.” slip op. at 14
Claim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 11,261,566 - PTAB · Nov 10, 2025 · IPR2025-00878 · APJ Carl M Defranco · IPR · Institution
The Board instituted review of claims 1–3 and 11 after finding a reasonable likelihood that claim 1 is anticipated by Cleveland or obvious over Nakagawa.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“contentions, the cited portions of Cleveland, and the testimony of Clearwater’s expert), we find, preliminarily, that Cleveland discloses each claim element in the manner recited by claim 1. Thus, on the current record, Clearwater demonstrates a reasonable likelihood that challenged claim 1 is unpatentable as anticipated by Cleveland.” slip op. at 6
- Novelty / Anticipation (§102) › Prior-art status of a reference › Patents / published applications (effective date, provisional support)Reference is prior artDecided for petitioner
“5 Clearwater argues that Cleveland qualifies as prior art under 35 U.S.C. § 102(e)(1) “based on both its provisional and non-provisional filing dates.” Pet. 17. In support, Clearwater asserts that Cleveland’s provisional (Ex. 1006) is “virtually identical” to Cleveland itself (id. at 18) and submits claim charts to demonstrate that the Cleveland provisional provides written support for: (1) at least claim 1 of Cleveland (id. at 18–21); and (2) the subject matter relied upon in Cleveland (id. at 21–40 (citing Ex. 1006 throughout)). Based on our review of the Cleveland provisional, as well as Clearwater’s claim charts, we are persuaded that the current record demonstrates that Cleveland is prior art to the challenged patent. See Dynamic Drinkware, LLC v. Nat’l Graphics, Inc., 800 F.3d 1375, 1381 (Fed. Cir. 2015).” slip op. at 4
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Instituted
“satisfies each claim element as identified above in Section I.D, i.e., elements [1.pre]–[1.6]. See id. at 22–40. Clearwater also submits annotated Figure 3 of Cleveland, reproduced below, to further illustrate the specific laminate structure of Cleveland’s coffee cup. See id. at 39.” slip op. at 5
- Obviousness (§103) › Motivation to combine / reasonable expectation of successInstituted
“protective layers have “a coat weight of from 5 to 30 lbs/3000 ft2,” Clearwater submits the declaration of its expert, who explains that, because Nakagawa identifies the specific polymers and the thickness of the coat used for the plastic layers and one skilled in the art “would recognize that the disclosed polymers have a given density,” then “[w]ith these known parameters, the coat weight is easily calculated to be 23.04 lbs./ 3000 ft2 — falling squarely within the claimed range.” Pet. 53–54 (citing Ex. 1003 ¶¶ 132–133; Ex. 1008 ¶ 24; Ex. 1024, at 4). At this stage, we find that testimony credible and supported by the evidence presently of record. After reviewing the preliminary record (including Clearwater’s contentions, the cited portions of Nakagawa, and the testimony of Clearwater’s expert), we find, preliminarily, that Nakagawa discloses or otherwise suggests each claim element in the manner recited by claim 1. Thus, on the current record, Clearwater demonstrates a reasonable likelihood that challenged claim 1 is unpatentable as obvious over Nakagawa. We need not decide Clearwater’s challenge of the dependent claims based on Nakagawa alone nor its challenge of claims 1–3 based on Nakagawa and Tanner. Our analysis of these challenges, in our view, is best left for trial after full development of the record.” slip op. at 8
Claim construction§ 102 anticipation§ 103 obviousnesscites PhillipsPatents in suitUS 8,637,126 - PTAB · Jul 10, 2025 · IPR2025-00175 · APJ Jo-Anne M Kokoski · IPR · Institution
The Board instituted review of claims 1–17 on all asserted grounds, finding a reasonable likelihood of unpatentability on at least one challenged claim.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“Institution of an inter partes review is authorized by statute when “the information presented in the petition . . . and any response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314 (2018); see also 37 C.F.R. § 42.4 (2023). For the reasons discussed below, we determine that Petitioner establishes a reasonable likelihood of prevailing with respect to the patentability of at least one claim of the ’562 patent. Accordingly, we institute an inter partes review of claims 1–17 of the ’562 patent.” slip op. at 2
- Skill levelSkill level petitioner adoptedDecided for petitioner
“(“POSITA”) would have had “at least a four-year degree in electrical engineering or a closely related field, and at least two years of experience in semiconductor device design,” and “[a]dditional education could substitute for professional experience and vice versa.” Pet. 6 (citing Ex. 1002 ¶¶ 80–” slip op. at 6
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached
“customary meaning of such claim as understood by one of ordinary skill in the art and the prosecution history pertaining to the patent.” 37 C.F.R. § 42.100(b). Under this standard, claim terms are generally given their plain and ordinary meaning as would have been understood by a person of ordinary skill in the art at the time of the invention and in the context of the entire patent disclosure. Phillips v. AWH Corp., 415 F.3d 1303, 1313 (Fed. Cir. 2005) (en banc). Only those terms in controversy need to be construed, and only to the extent necessary to resolve the controversy. Realtime Data LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019). Neither party proposes any explicit construction of any term. See Pet. 7 (“For the purposes of this IPR, the plain meaning of each term can be applied.”). We do not expressly construe any term for purposes of this Decision.” slip op. at 7
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Instituted
“On this record, we are persuaded that Petitioner adequately establishes that Usui discloses all of the limitations of claim 1. Usui discloses that aluminum or aluminum alloy layer 15 is in electrical contact with titanium underlayer 13, and titanium nitride layer 14 is located “intermediate the [titanium underlayer] 13 and the aluminum or aluminum alloy layer 15” to prevent “reaction between the aluminum layer 15 and underlayer 13.” Ex. 1004, 3:27–29, 3:38–41, 3:58–63. Usui further discloses that “a capping layer is provided above layer 15,” and that “[p]referred capping layers are titanium nitride and combinations of as layer 18 of a group IVA metal, preferably titanium with a titanium nitride layer 19.” Id. at 3:67–4:6. Usui teaches that titanium nitride layer 19 is about 150 to 800 Å thick, and that the thickness of titanium underlayer 13 is between about 90 to 110 Å. Id. at 3:31–33, 4:6–8. Usui also teaches that the interconnect metallurgy structures described therein “exhibit[] enhanced electromigration characteristics” and “are especially useful for forming electrical connections or wiring such as between active and/or passive devices of an integrated circuit structure.” Id. at 1:8–14. Usui’s description of a plurality of metal layers (layers 13–18) and a capping layer formed over the plurality of metal layers (layer 19), along with its description of the structure’s usefulness for forming electrical connections in an integrated circuit structure, is sufficient, on this record, to establish that Usui discloses “an electrode stack including a plurality of metal layers and a capping layer formed over said plurality of metal layers” as recited in claim 1. Usui’s teaching that the capping layer is a refractory metal nitride (titanium nitride) that has a thickness (150–800 Å) greater than the bottommost layer of the plurality of metal layers (layer 13, 90–110 Å), sufficiently establishes, on this record, that Usui discloses the “said capping layer consisting only of a refractory metal nitride, said refractory metal nitride forming a top of said electrical contact and having a thickness greater than that of a bottommost layer of said plurality of metal layers” limitation of claim 1.” slip op. at 11
Claim construction§ 102 anticipation§ 103 obviousnesscites PhillipsPatents in suitUS 8,686,562 - PTAB · Jul 9, 2025 · IPR2025-00094 · APJ Christopher M Kaiser · IPR · Institution
The Board instituted IPR on claims 1–16 and all asserted grounds, finding a reasonable likelihood that claim 1 is obvious over Bonn and Mizuta.
RulingsInstitution decision- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“At this preliminary stage, we determine whether the information presented shows a reasonable likelihood that Petitioner would prevail in establishing that at least one of the challenged claims would have been unpatentable over the proposed prior art. We analyze the asserted grounds with the above-noted principles in mind.” slip op. at 7
- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that one of ordinary skill in the art “would have possessed at least a four-year degree in electrical engineering or a closely related field, and at least two years of experience in semiconductor device design.” Pet. 5 (citing Ex. 1003 ¶¶ 67–69). Petitioner also argues that “[a]dditional education could substitute for professional experience and vice versa.” Id. On the present record, Patent Owner does not dispute Petitioner’s proposed level of ordinary skill. Prelim. Resp. 1–52. Neither party explains why the outcome of this case would be affected by the adoption of any of the proffered definitions of a person of ordinary skill in the art. For purposes of this Decision, we adopt Petitioner’s assessment of the level of ordinary skill in the art, as it appears to be consistent with the ’003 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 8
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther
“We apply the same claim-construction standard used in the federal courts—in other words, the claim-construction standard that would be used to construe the claim in a civil action under 35 U.S.C. § 282(b), which is articulated in Phillips. See 37 C.F.R. § 42.100(b). Under the Phillips standard, the “words of a claim ‘are generally given their ordinary and customary meaning,’” which “is the meaning that the term would have to a person of ordinary skill in the art in question at the time of the invention, i.e., as of the effective filing date of the patent application.” Phillips, 415 F.3d at 1312–13. Neither party proposes construing any claim terms. Pet. 6; Prelim. Resp. 1–52. On the present record, we agree. As discussed below, we are able to determine whether to institute inter partes review of the ’003 patent without expressly construing any terms. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 9
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundInstituted
“Patent Owner argues that Petitioner does not show sufficiently that a person of ordinary skill in the art would have had a reason to modify Bonn to remove local oscillator 55. Prelim. Resp. 13–15. We disagree. Petitioner argues that, “[i]n addition to using Figure 7’s ‘dual gate FET structure in high frequency signal mixing’ applications . . . , Bonn discloses using this dual gate FET in ‘other applications such as high frequency signal amplification.’” Pet. 22 (quoting Ex. 1006, 11:26–37). Indeed, Bonn does suggest using its structure for signal amplification. Ex. 1006, 11:26–37 (“the dual gate FET structure of the present invention can be tailored to provide superior performance . . . in . . . other applications such as high frequency signal amplification”). On the present record, this appears to have provided the motivation for a person of ordinary skill in the art to use Bonn for amplification instead of for signal mixing. Petitioner relies on the testimony of Dr. Bernstein to show the modifications that a person of ordinary skill in the art would have considered necessary in order to convert Bonn’s structure for signal-amplification use. Pet. 23–25 (citing Ex. 1003 ¶¶ 98–109). In particular, Petitioner cites Dr. Bernstein’s testimony that a person of ordinary skill in the art “would have found it obvious to remove Figure 1’s LO (local oscillator) port 55 and its associated impedance matching components because the LO signal is no longer being mixed.” Ex. 1003 ¶ 98; see Pet. 23. Dr. Bernstein supports this testimony with citations to Bonn and with reasoning regarding why a person of ordinary skill in the art would have made this modification. Ex. 1003 ¶ 98 (citing Ex. 1006, 1:20–23, 3:19–21, 3:30–41). Accordingly, on the present record, we are persuaded that Petitioner has shown sufficiently that a person of ordinary skill in the art would have had reason to modify Bonn’s structure to remove the connection between a local oscillator and the gate of the second transistor. Finally, Patent Owner argues that Petitioner’s proposed modification would have rendered Bonn inoperable for its intended purpose because the modification would eliminate the ability of Bonn’s structure to conduct high frequency signal mixing. Prelim. Resp. 26–27. As Patent Owner notes, one purpose of Bonn is to mix high-frequency signals. Ex. 1006, 11:33–36. But Bonn itself teaches using its structure for “other applications,” including “high frequency signal amplification.” Id. at 11:33–37. Thus, on the present record, we are persuaded that Petitioner’s proposed modification does not render Bonn inoperable for its intended purpose so much as it acknowledges the modifications necessary to convert Bonn from one of its intended purposes to another. Thus, Petitioner has shown sufficiently for the purpose of the present Decision that a person of ordinary skill in the art would have had reason to combine Bonn and Mizuta and that the combination of Bonn and Mizuta teaches or suggests the disputed limitation of claim 1. We encourage the parties to develop the arguments and the record surrounding this issue further during the trial.” slip op. at 14
Claim construction§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 8,264,003 - PTAB · Jun 18, 2025 · IPR2025-00321 · APJ Christopher M Kaiser · IPR · Institution
The Board instituted IPR on claims 1, 2, 5–7, 9, 16, and 17, finding a reasonable likelihood that claim 1 is anticipated by Boyer.
RulingsInstitution decision- PTAB / AIA Trials › Discretionary denial › Fintiv (parallel litigation)Denied
“approximately two weeks before the statutory deadline for a final written decision, but the most recent median time-to-trial statistics for Judge Gilstrap in the Eastern District of Texas indicate that the actual trial date will likely be in July 2026, which is later than the statutory deadline to issue a final written decision in this proceeding in mid-June 2026. See Ex. 2001, 7 (median time from filing to trial of 23.2 months); Prelim. Resp. 10. Thus, we find this factor is neutral or weighs slightly against discretionary denial.” slip op. at 10
- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“At this preliminary stage, we determine whether the information presented shows a reasonable likelihood that Petitioner would prevail in establishing that at least one of the challenged claims would have been unpatentable over the proposed prior art. We analyze the asserted grounds with the above-noted principles in mind.” slip op. at 7
- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner contends that one of ordinary skill in the art “would have had (1) at least a bachelor’s degree in Mechanical Engineering, Computer Engineering, Chemical Engineering, Materials Science, or a related field, and (2) at least two years of research or industry experience in 3D printing or materials used for 3D printing.” Pet. 5 (citing Ex. 1003 ¶¶ 14–16). Petitioner also argues that “[a]dditional experience could substitute for a formal degree or formal training (and vice versa).” Id. Patent Owner proposes a slightly different level of skill, arguing that a person of ordinary skill in the art “would have had a bachelor’s degree in Mechanical Engineering, Computer Engineering, Chemical Engineering, Materials Science, or a comparable field and at least two years of experience related to 3D printing, with additional experience potentially being a substitute for a formal degree or training (and vice versa).” Prelim. Resp. 24. Neither party explains why the outcome of this case would be affected by the adoption of any of the proffered definitions of a person of ordinary skill in the art. For purposes of this Decision, we adopt Petitioner’s assessment of the level of ordinary skill in the art, as it appears to be consistent with the ’713 patent and the asserted prior art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 16
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction needed
“We note that, as discussed below, we are able to determine whether to institute inter partes review of the ’713 patent without expressly construing the term “from multiple print heads or deposition lines.” See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))). As for Patent Owner’s argument that Petitioner has failed to carry its burden to identify how the claims are to be construed, we disagree on the present record. Although Petitioner does not provide a preferred construction for the single term it proposes requires construction, Petitioner does identify which of its two alternative constructions applies to each of its asserted grounds of unpatentability. Pet. 6 (“Under the first construction, [the obviousness grounds] are applicable, and [the anticipation ground] would be excluded from the claim scope. Under the alternative construction, all of [the asserted grounds] are applicable.”). In our view, this approach does not fail to satisfy Petitioner’s burden under 37 U.S.C. § 42.104(b)(3).” slip op. at 17
Claim construction§ 102 anticipationDiscretionary denialcites PhillipsPatents in suitUS 9,421,713 - PTAB · Jun 18, 2025 · IPR2025-00311 · APJ Christopher M Kaiser · IPR · Institution
The Board instituted IPR of claims 1, 3–11, and 17–22 on all asserted grounds because Petitioner showed a reasonable likelihood of prevailing on claim 1 over Mazumder and Mori.
RulingsInstitution decision- PTAB / AIA Trials › Discretionary denial › Fintiv (parallel litigation)Decided for petitioner
“based on Petitioner’s first stipulation filed on December 18, 2024.15 Prelim. Resp. 13–15. Patent Owner does not address Petitioner’s updated second stipulation filed on April 8, 2025. This updated second stipulation mitigates any concerns of duplicative efforts between the district court and the Board, as well as concerns of any potentially conflicting decisions. See Sand at 12. We therefore find that this factor weighs against exercising discretion to deny institution. See id., n.5. 5. Whether Petitioner and the Defendant in the Parallel Proceeding are the Same Party Whereas Petitioner does not address factor 5, Patent Owner argues that the parties to this proceeding are both in the related district court litigation. Pet. 98–99; Prelim. Resp. 15. While it is common in IPR proceedings for the petitioner and patent owner to also be parties in a related district court proceeding, this factor weighs slightly in favor of discretionary denial. Fintiv, Paper 11 at 13–14.” slip op. at 15
- PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)InstitutedInstituted
“c) Conclusion Regarding Claim 1 Based on the current record, we determine that there is a reasonable likelihood that Petitioner will prevail in demonstrating that claim 1 is unpatentable as obvious over the combination of Mazumder and Mori. Accordingly, we institute inter partes review with respect to all claims and all grounds asserted in the Petition. 5. Claims 3, 5–7, 9, 10, and 19–22 Because Petitioner demonstrates a reasonable likelihood of success in proving that at least one claim of the ’324 patent is unpatentable, we institute on all grounds and all claims raised in the Petition. See 37 C.F.R. § 42.108(a). Therefore, at this stage of the proceeding, it is not necessary for us to provide an assessment of every challenge raised by Petitioner, especially, as in this case, when Patent Owner does not separately argue those claims. See Prelim. Resp. 28–46. Those challenges, in our view, are best left for trial after full development of the record.” slip op. at 27
- Obviousness (§103) › Analogous artAnalogous artDecided for petitioner
“reference must be analogous art to the claimed invention. In re Bigio, 381 F.3d 1320, 1325 (Fed. Cir. 2004). For a reference to be analogous art, it must be “either in the field of the applicant's endeavor or [be] reasonably pertinent to the problem with which the inventor was concerned.” In re Kahn, 441 F.3d 977, 986-87 (Fed. Cir. 2006) (citing In re Oetiker, 977 F.2d 1443, 1447 (Fed. Cir. 1992)). “A reference is reasonably pertinent if, even though it may be in a different field from that of the inventor's endeavor, it is one which, because of the matter with which it deals, logically would have commended itself to an inventor's attention in considering his problem.” In re Clay, 966 F.2d 656, 659 (Fed. Cir. 1992).” slip op. at 20
- Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundInstituted
“Mazumder because “the presentation of both image types would have beneficially aided the remote user to more easily visually compare the actual image and virtual image to quickly identify any defects or problems with the fabrication process.” Pet. 23–24 (citing Ex. 1003 ¶ 113). Patent Owner argues that “it is hindsight to use ‘the invention to define the problem the invention solves.’” Prelim. Resp. 43 (quoting Mintz v. Dietz & Watson, Inc., 679 F.3d 1372, 1377 (Fed. Cir. 2012); citing AT&T Services Inc. et. al. v. Innovative Sonic Ltd., IPR2024-001143 (PTAB Feb. 11, 2025)). According to Patent Owner, because neither Mazumder nor Mori teaches visual comparison of image types, the idea to improve the Mazumder-Mori combination by simultaneously displaying different image types and thus permitting visual comparison must be driven by hindsight. Id. at 44–45. But Petitioner cites evidence other than the ’324 patent to support the person of ordinary skill in the art having a desire to visually compare the different images presented in the Mazumder-Mori combination. Pet. 23–24 (citing Ex. 1003 ¶ 113). Specifically, Dr. Wolfe testifies that “the presentation of the actual images captured by the camera and the virtual images simultaneously within the user interface would have beneficially aided the remote user to more easily visually compare the actual image and virtual image to quickly identify any defects or problems with the fabrication process” and that a person of ordinary skill in the art would have recognized this. Ex. 1003 ¶ 113. Thus, Petitioner has shown sufficiently for the purpose of the present decision that Mori teaches or suggests the disputed limitation of claim 1. We encourage the parties to develop the arguments and the record surrounding this issue further during the trial.” slip op. at 26
Claim construction§ 103 obviousnessDiscretionary denialcites Phillips · KSR · GrahamPatents in suitUS 8,562,324 - Njoy, LLC / Njoy Holdings, Inc. v. Juul Labs, Inc.No claims unpatentablePTAB · Jun 10, 2025 · IPR2024-00231 · APJ Avelyn M Ross · IPR · Final written decision
Claims 14–16, 18, 27–29, 31, and 32 were not proven unpatentable because the asserted references failed to establish the claimed airflow path or a reason to make the proposed combinations.
RulingsFinal written decision- Skill levelSkill level petitioner adoptedDecided for petitioner
“Petitioner’s and Patent Owner’s proposed levels of skill are similar and differ in that Petitioner’s relevant degrees and corresponding two years of experience additionally includes “industrial design” and “product design” and familiarity with “electrically powered vaporizing articles, their components or the underlying technologies” where Patent Owner requires two years of experience “designing electro-mechanical consumer products or an advanced degree.” Compare Pet. 7, with PO Resp. 2. Patent Owner alleges that “Petitioner has failed to establish unpatentability under either standard,” indicating that the level of skill in the art is not a dispositive issue. PO Resp. 3. In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’123 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’123 patent and the prior art. We note that the outcome of this Decision would be the same under Patent Owner’s proposed definition.” slip op. at 11
- Expert testimonyPetitioner expert creditedOther
“In this case, Mr. McAlexander meets both Petitioner’s and Patent Owner’s proposed level of skill in the art. As a result, we are persuaded Mr. McAlexander has the requisite skill and relevant expertise to offer testimony in this matter. For example, Mr. McAlexander has a Bachelor’s Degree in Electrical Engineering and far more than 2 years of experience in the electrical engineering field. Ex. 1027, 3–6, 7. In addition, Mr. McAlexander has provided expert consulting services in a wide range of technology areas involving the process and design of electro-mechanical consumer products. Ex. 1003 ¶ 5. Through one of Mr. McAlexander’s business ventures, his laboratory has “performed detailed airflow analyses, designing and constructing specialized apparatuses to emulate human breath, allowing for precise activation testing of ENDS devices.” Ex. 1043 ¶ 16. That said, a declarant’s expertise, even clothed as a skilled artisan, does not entitle a naked opinion persuasive weight. Ashland Oil, Inc. v. Delta Resins & Refractories, Inc., 776 F.2d 281, 294 (Fed. Cir. 1985). Here, Patent Owner had the opportunity to, and in fact did, thoroughly cross examine Mr. McAlexander about the purported deficiencies in his testimony. See, e.g., Exs. 2052, 2054; Daubert v. Merrell Dow Pharm., Inc., 509 U.S. 579, 595 (1993) (“Vigorous cross examination [and] presentation of contrary evidence . . . are the traditional and appropriate means of attacking shaky but admissible evidence.”). Therefore, to the extent Patent Owner credibly identifies deficiencies in Mr. McAlexander’s testimony or that testimony lacks factual support or is based on broad, conclusory assertions, we will assign appropriate weight. See Velander v. Garner, 348 F.3d 1359, 1371 (Fed. Cir. 2003) (explaining that it is within the Board’s discretion, as the trier of fact, to accord appropriate weight to the evidence presented).” slip op. at 12
- Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached
“Petitioner contends that the parties proposed a construction for “pressure valve,” a limitation appearing in claims 18 and 31, during the ITC investigation. Pet. 7 (citing Ex. 1001, 41:58–65). Patent Owner contends that the terms of the ’123 patent should be given their plain and ordinary meaning. PO Resp. 4. Because resolution of the issues presented in this case do not require construction of the term “pressure valve,” we do not expressly construe this claim term. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 14
- Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable
“We agree with Patent Owner. To anticipate a claim, a reference “must not only disclose all elements of the claim within the four corners of the document, but must also disclose those elements ‘arranged as in the claim.’” Net MoneyIN, 545 F.3d at 1369. “The requirement that the prior art elements themselves be arranged as in the claim means that the claims cannot be treated . . . as mere catalogs of separate parts, in disregard of the part-to-part relationships set forth in the claims.” Therasense, Inc. v. Becton, Dickinson & Co., 593 F.3d 1325, 1332 (Fed. Cir. 2010). Indeed, the prior art reference “must clearly and unequivocally disclose the claimed [invention] or direct those skilled in the art to the [invention] without any need for picking, choosing, and combining various disclosures not directly related to each other by the teachings of the cited reference.” Net MoneyIN, 545 F.3d at 1371 (citation omitted). “[D]ifferences between the prior art reference and the claimed invention, however slight, invoke the question of obviousness, not anticipation.” Id.” slip op. at 20
Patent outcomesUS 10,130,123 not shown unpatentableClaim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · GrahamPatents in suitUS 10,130,123
Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.