• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00187 · APJ Debra L Dennett · IPR · Final written decision

  Claims 1–17 are unpatentable under § 103, principally because Chang in view of Jin renders them obvious; the Jin/Feldmann grounds were not shown.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49).” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11

  • Expert testimonyPatent owner expert creditedDecided for patent owner

    “gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard. Without an apparent reason to modify the teachings of Jin and Feldmann to” slip op. at 19

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 17

  Patent outcomesUS 10,230,009 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,230,009
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00006 · APJ Debra L Dennett · IPR · Final written decision

  Claims 1–17 are unpatentable under § 103, principally over Chang and Jin; the Board rejected the Jin and Feldmann combinations for lack of a reason to combine.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’009 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’009 patent and the prior art.” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 26. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 116 with Pet. 26). Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” See Magnum, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard.” slip op. at 19

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” Resp. 42 (citing Ex. 1013 ¶ 76). In so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Id. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Chang ¶ 62; Tr. 15:20–17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 73, 217 (citing Ex. 1023 § 1). Chang also discloses that the emitter area may be formed by thermal diffusion, ion implantation or the like. Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding a tunneling layer and a base surface field area from periphery region and isolation region. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” slip op. at 32

  Patent outcomesUS 10,230,009 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,230,009
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00918 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board rejected the Jin and Feldmann based grounds for lack of a reason to combine without hindsight.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “Patent Owner focuses on Chang’s description in paragraph 76 of a single configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” PO Resp. 42–43 (citing Ex. 1013 ¶ 76). But, in so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Ex. 1013 ¶ 62; Tr. 15:20– 17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 70–81, 91–96, 200 (citing Ex. 1026 § 1 and stating that “[b]oth Chang and Jin likewise teach backside isolation regions”). Chang also discloses that the emitter area may be formed by “thermal diffusion, ion implantation or the like.” Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Pet. Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding the second tunneling layer and a base surface field area from periphery region and isolation portion. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art “reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” Ex. 1003 ¶ 201.” slip op. at 33

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00186 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board found the combination disclosed the claimed isolation portion and supported the challenged claims.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “C. Claim Construction We construe claim terms according to the standard set forth in Phillips v. AWH Corp., 415 F.3d 1303, 1312–17 (Fed. Cir. 2005) (en banc); 37 C.F.R. § 42.100(b). Under Phillips, we give claim terms “their ordinary and customary meaning.” Phillips, 415 F.3d at 1312. “[T]he ordinary and customary meaning of a claim term is the meaning that the term would have to a person of ordinary skill in the art in question at the time of the invention.” Id. at 1313. “Importantly, the person of ordinary skill in the art is deemed to read the claim term not only in the context of the particular claim in which the disputed term appears, but in the context of the entire patent, including the specification.” Id. Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Expert testimonyPetitioner expert discountedPatent owner expert creditedMixed

    “edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001” slip op. at 18

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00007 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under §103 over Chang and Jin because the combination teaches the claimed isolation portion and the claimed tapering.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedOther

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightTeaching away not foundNot shown unpatentable

    “On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  • Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner

    “However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide.” slip op. at 18

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• Innoscience (Zhuhai) Technology Company, Ltd. / Innoscience America, Inc. v. Efficient Power Conversion CorporationAll claims unpatentable
  PTAB · Mar 25, 2025 · IPR2023-01384 · APJ Jeffrey W Abraham · IPR · Final written decision

  Claims 1–7 are unpatentable as obvious over Yoshida and Saxler; the Board did not reach the alternative grounds.

  RulingsFinal written decision

  • Skill levelOther

    “In light of the record before us, we determine that we do not need to reach a specific finding regarding the level of ordinary skill in the art. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (explaining that specific findings regarding ordinary skill level are not required “where the prior art itself reflects an appropriate level and a need for testimony is not shown”) (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163 (Fed. Cir. 1985)).” slip op. at 13

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for petitioner

    “In the Institution Decision, we declined to adopt Petitioner’s proposed construction of the “side surfaces” limitation and determined that it was not necessary to further construe this term because “[t]he parties do not dispute that the language ‘side surfaces extending horizontally’ encompasses a gate material with sloped side surfaces as depicted in Figure 5 of the ’335 patent.” Inst. Dec. 11–16 (citing Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017); Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)). We invited the parties to address this limitation further during the course of this trial, but neither party provided additional evidence or argument regarding the “side surfaces” limitation. Inst. Dec. 16; see generally PO Resp.; Reply; Sur-reply. Accordingly, we maintain our determination from the Institution Decision that we do not need to construe the “side surfaces” limitation. Inst. Dec. 15– 16.” slip op. at 14

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “This evidence, particularly the language in the ’335 patent itself, undermines Patent Owner’s argument that “[t]he process for forming gate ledges using separate masks instead of the self-aligned process disclosed in the ’335 patent cannot produce ledges that are ‘substantially symmetric.’” PO Resp. 39 (emphasis added); see also PO Resp. 42–43 (arguing that a gate structure with ledges having substantially equal widths is “not achievable” without using a single photo-mask process). We have considered the evidence presented by Patent Owner and Dr. Schubert in support of Patent Owner’s arguments. PO Resp. 38–43; Ex. 2005 ¶¶ 49–51. We, however, are unable to discern sufficient evidence supporting a conclusion that using separate masks cannot produce ledges that are substantially symmetric, particularly when the ’335 patent suggests otherwise. See Ex. 1001, 4:60– 63 (referring only to the “possibility of misalignment”). Even if, as Patent Owner and Dr. Schubert contend, misalignment “naturally” occurs when using a two-mask process, that does not foreclose the possibility that the” slip op. at 18

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner

    “It is well settled that “[a] reference does not teach away . . . if it merely expresses a general preference for an alternative invention but does not ‘criticize, discredit or otherwise discourage’ investigation into the invention claimed.” DePuy Spine, Inc. v. Medtronic Sofamor Danek, Inc., 567 F.3d 1314, 1327 (Fed. Cir. 2009) (quoting In re Fulton, 391 F.3d 1195, 1201 (Fed. Cir. 2004)). Furthermore, “teaching that a composition may be optimal or standard does not criticize, discredit, or otherwise discourage” slip op. at 31

  Patent outcomesUS 10,312,335 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,312,335
• Amphenol Corp. v. PPC Broadband, Inc.All claims unpatentable
  PTAB · Feb 19, 2025 · IPR2023-01363 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 1, 2, and 10–13 are unpatentable as obvious over the stated combinations of Holmberg, Battey, Blankenship, and Cowen.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends a person of ordinary skill in the art “would have had at least a bachelor’s degree in electrical engineering, computer engineering, or a related field, and at least 1 year of experience related to communication networks or the equivalent.” Pet. 7. Petitioner further contends that “[a]dditional education could substitute for professional experience or significant experience in the field could substitute for formal education.” Id. at 7–8 (citing Ex. 1003 ¶¶ 29–31). Dr. Eldering agrees that one of ordinary skill in the art “would have had at least a bachelor’s degree in electrical engineering, computer engineering, or a related field, and at least one year of experience related to communication networks or the equivalent.” Ex. 2001 ¶ 24. According to Dr. Eldering, “[a] person with less relevant practical experience but with additional experience would also qualify.” Id. Patent Owner contends that” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “Although Patent Owner disagrees with Petitioner’s construction, it contends “the Board need not resolve this claim construction dispute because Petitioner’s proposed grounds 1-5 are all insufficient under either construction.” PO Resp. 19. Upon review of the parties’ arguments and the prior art of record, we determine that no claim terms require express construction for purposes of this decision. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)). For example, we discuss below in Section III.G why we do not reach the claim construction issue presented by Petitioner.” slip op. at 11

  • Expert testimonyPetitioner expert creditedDecided for petitioner

    “We find that Holmberg expressly contemplates using its wall box within multi-dwelling units, notes that multi-dwelling wall boxes in the prior art were “typically provided” on every floor, and discloses that the multi-dwelling wall boxes would contain optical couplings for each resident on a given floor. Ex. 1004 ¶¶ 7, 34; Pet. Reply 8–10. In view of these disclosures, we credit the testimony of Dr. Kiaei that one of ordinary skill in the art would have sought to use Holmberg’s wall box in multi-dwelling units and would have seen a need to access the area behind spice tray 230 to connect and disconnect subscribers. Ex. 1003 ¶ 92; Ex. 1033 ¶¶ 7–8. Moreover, even if Holmberg were limited to mid-span locations and distributing drop cables, as opposed to distribution cables for individual subscribers, as asserted by Patent Owner, Patent Owner does not dispute that a technician would still need periodic access to the area behind splice tray 230 in these mid-span devices. Tr. 38:3–39:1 (counsel agreeing that one would need to access the area behind splice tray 230 in Holmberg, albeit in “rare occasions”); Ex. 1003 ¶¶ 90–92; Ex. 1033 ¶¶ 7–8. Thus, whether used in the manner contemplated by Petitioner or Patent Owner, Petitioner persuasively demonstrates that access to the space behind splice tray 230 in Holmberg would be necessary. With access behind splice tray 230 required, Petitioner persuasively demonstrates that one of ordinary skill in the art would have seen a benefit to replacing Holmberg’s fasteners or screws with a hinged connection, such as that disclosed in Battey, to allow easier access to the area behind the splice tray. Pet. 41 (citing Ex. 1005 ¶ 39 (disclosing that a rotatable splice tray or shelf would “provide[] full and convenient access to the splice tray”)). First, Petitioner and Dr. Kiaei persuasively demonstrate that once the fibers of Holmberg are routed from behind splice tray 230 and the distribution cables spooled on this tray, a technician could not reasonably access fiber optic cables stored behind splice tray 230 without releasing or opening splice tray 230. Pet. Reply 14–15 (citing Ex. 1023, 60:20–61:15); Ex. 1033 ¶¶ 31–32. Second, Petitioner persuasively demonstrates that without a hinged connection, the technician would have to either hold the splice tray of Holmberg with one hand while performing the necessary routing and splicing steps, two screws would need to remain in place (essentially replicating a hinge), or the tray would have to be left to dangle, supported only by the routed and spliced fibers. Pet. Reply 19–20.” slip op. at 22

  • Strike new argumentNew argument consideredDecided for petitioner

    “Allegedly New Arguments on Reply Patent Owner contends that Petitioner’s arguments regarding the benefits of a hinged connection when performing the splicing and routing steps should be dismissed or ignored because they were improperly raised for the first time on reply. Sur-reply 19–20. We disagree. The Petition asserts that one of ordinary skill in the art would have sought to add a hinged connection, such as that disclosed in Battey, in Holmberg and would have seen a benefit to so doing. Pet. 40–44. Petitioner did not change its proposed combination or its stated rationale in its Reply. Rather, in response to Patent Owner’s counter-arguments, Petitioner expands upon the benefits of its proposed combination, i.e., the substitution of a hinged connection in place of fasteners. Pet. Reply 15–21. This is permissible, as a reply may properly expand on or extend previously raised arguments relating to the motivation to make the proposed changes to the prior art. See Rembrandt Diagnostics, LP v. Alere, Inc., 76 F.4th 1376, 1385 (Fed. Cir. 2023) (explaining that the reply arguments properly relied on the same legal ground, the same prior art references, and same legal argument—the motivation to make the proposed changes to the prior art reference).” slip op. at 25

  Patent outcomesUS 9,008,483 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,008,483
• Apple Inc. v. RJ Technology LLCSome claims unpatentable
  PTAB · Feb 18, 2025 · IPR2023-01350 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 5–10 are unpatentable as obvious; claims 11–14 were not shown unpatentable because the evidence did not establish the claimed capacity retention after 400 cycles.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends a person of ordinary skill in the art “would have held a Bachelor’s degree in chemistry or chemical engineering, with at least 4 years of experience in cell design, electrochemical techniques, and battery materials development.” Pet. 4. Petitioner further contends that a “Master’s Degree can substitute[] for some of the relevant experience,” and “[e]quivalent training with battery specific experience can accommodate other degreed fields.” Id. 9 The parties here do not address objective evidence of nonobviousness. Patent Owner does not dispute Petitioner’s definition of the ordinarily skilled artisan. PO Resp. 20. We adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the ’641 patent, the prior art of record, and the parties’ arguments.” slip op. at 6

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “The parties agree that the term “charge cut-off voltage” is “the maximum voltage to which the battery is configured to be charged.” PO Resp 21–22; Pet. Reply 1. The parties dispute, however, whether the “charge cut-off voltage” is a “battery property” or “the voltage applied to the battery during charging.” PO Resp. 21–24; Pet. Reply 1–6. We need not resolve the precise meaning of “charge cut-off voltage” because there is no dispute that Yamaki discloses this limitation under either party’s interpretation of the claim term. Upon review of the prior art and the parties’ arguments, we determine that no terms of the ’641 patent require express construction. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’” (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))); Pet. Reply 1 (asserting that the challenged claims are unpatentable under either parties’ construction of “charge cut-off voltage”).” slip op. at 7

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “Patent Owner’s arguments do not persuasively undermine Petitioner’s position. Sakamoto expressly discloses setting the ratio of negative to positive electrode active material in the range of 1.05 to 1.30. Ex. 1005 ¶ 8. Sakamoto also explains why this range is preferable, i.e., if the ratio is roughly equal “the charge-discharge cycle performance is insufficient due to significant deterioration from charging and discharging,” and if the ratio is 10 Citations to the prosecution history of Yamaki are to the page numbers added to the lower right corner of the document. too high “too much of the compound does not participate in charging and discharging.” Id. ¶¶ 6, 8. These disclosures are sufficient to explain why one of ordinary skill in the art would have found it obvious to select the ratios disclosed in Sakamoto in Yamaki. Id. ¶ 8 (providing a secondary battery with a capacity ratio between 1.05 and 1.30 and noting that by setting the ratio within this range the resulting secondary lithium battery is “safe due to low risk of heat being generated and an explosion occurring”). We also disagree that Sakamoto teaches away from elevated voltages or from increasing the amount of lithium in circulation. See PO Resp. 29. Contrary to Patent Owner’s arguments, Sakamoto provides no general teaching against using a charge cut-off voltage above 4.2 V, or against increasing the level of lithium in circulation. Nor does Sakamoto “criticize, discredit, or otherwise discourage” the claimed invention. In re Fulton, 391 F.3d 1195, 1201 (Fed. Cir. 2004). Rather, Sakamoto warns against setting the reversible capacities of the positive and negative electrode substantially equal as this may result in excess lithium plating on the surface of the electrode. Ex. 1005 ¶¶ 6, 8. We agree with Petitioner that this disclosure would lead one of ordinary skill in the art to design a battery with a higher capacity in the negative electrode active material than the positive electrode active material. Pet. 11–12.” slip op. at 14

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › Teaching awayTeaching away not foundDecided for petitioner

    “We also disagree that Sakamoto teaches away from elevated voltages or from increasing the amount of lithium in circulation. See PO Resp. 29. Contrary to Patent Owner’s arguments, Sakamoto provides no general teaching against using a charge cut-off voltage above 4.2 V, or against increasing the level of lithium in circulation. Nor does Sakamoto “criticize, discredit, or otherwise discourage” the claimed invention. In re Fulton, 391 F.3d 1195, 1201 (Fed. Cir. 2004). Rather, Sakamoto warns against setting the reversible capacities of the positive and negative electrode substantially equal as this may result in excess lithium plating on the surface of the electrode. Ex. 1005 ¶¶ 6, 8. We agree with Petitioner that this disclosure would lead one of ordinary skill in the art to design a battery with a higher capacity in the negative electrode active material than the positive electrode active material. Pet. 11–12.” slip op. at 15

  Patent outcomesUS 7,749,641 mixed
  Claim construction§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 7,749,641
• Opticis Co., Ltd. v. Inneos LLCAll claims unpatentable
  PTAB · Jan 29, 2025 · IPR2023-01256 · APJ Terry J Owens · IPR · Final written decision

  Claims 1, 2, 6, 7, and 9 are unpatentable as obvious over Kurita and Lemoff, with the Board declining to reach the remaining grounds.

  RulingsFinal written decision

  • Skill levelSkill level board ownDecided for petitioner

    “We accept the level of ordinary skill in the art stated by Petitioner and agreed with by Patent Owner with the exception of the open-ended language appears consistent with the ’416 patent and the prior art of record.” slip op. at 7

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “describe elements that are not affirmatively recited in the claims, and in view of the “bedrock principle of patent law that the claims of a patent define the invention,” we conclude that none of the unrecited limitations identified by Patent Owner are required by the claims. See Thorner v. Sony Entm’t Am. LLC, 669 F.3d 1362, 1366 (Fed. Cir. 2012) (explaining that the standard for disavowal is “exacting,” and the use of “the present invention” is not necessarily sufficient to meet this standard).” slip op. at 12

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundDecided for petitioner

    “art would not have modified Kurita in view of Lemoff because Lemoff positions the signal emitters near the fiber to emulate WDM without the need for an external optical multiplexer or a similar device and discourages using optical wavelength multiplexers for short distances because the complexity of the design is often cost prohibitive (PO Resp. 47–48), Lemoff does not appear to limit the usefulness of the fiber connector to any particular optical signal transmission distance. Petitioner relies upon Lemoff for a suggestion to combine Lemoff’s fiber connector configuration teachings with Kurita’s multiplexer teachings to enable fibers to be plugged Fig. 2) (Pet 29, 31; Reply 17–18). Regarding Patent Owner’s argument that one of ordinary skill in the art would not have combined Lemoff’s receptacle and ferrule with discrete components in Kurita because the fiber would need to be manually fixed and aligned with or without a ferrule and, therefore, would serve no purpose (PO Resp. 48), Lemoff’s fiber connector appears to fix and align the fiber adequately for wavelength division multiplexing without manual fixation or alignment being required (Ex. 1006, 5:65–6:2, Fig. 2; Reply 18). The challenged claims do not require any greater degree of fixing and alignment than that provided by Lemoff’s fiber connector. Regarding Patent Owner argument that Lemoff’s device is not physically combinable with Kurita’s WDM multiplexer due to Lemoff’s device’s small size (PO Resp. 47–48; Reply 17–18), “[t]he test for obviousness is not whether the features of a secondary reference may be bodily incorporated into the structure of the primary reference.... Rather, the test is what the combined teachings of the references would have suggested to those of ordinary skill in the art” (In re Keller, 642 F.2d 413, 425 (CCPA 1981)). Accordingly, we are not persuaded by Patent Owner’s argument.” slip op. at 26

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)UnpatentableUnpatentable

    “stopped single optical fiber because fixing it in place does not passively align it with the optical components (PO Resp. at 35–37) is not persuasive because fixing Kurita’s fiber (40) in place in accord with Lemoff’s teaching regarding the ferrule (255) inserted until being stopped by the receptacle (260) (Ex. 1006, 5:50–6:15, Fig. 2) would align Kurita’s optical array (20), and lens (30)) (Ex. 1004 Fig. 3) passively in the same manner that Lemoff’s ferrule (255), after being inserted until stopped by the receptacle (260), passively aligns the optical fiber (250) with the optical components (optical imaging element 220 and light emitters within emission apertures 120) (Ex. 1006, 5:50–6:15, Fig. 2; Reply 15–16). Regarding Patent Owner’s argument that the light from each of Kurita’s lasers (11) depicted in Figure 3 cannot pass through a separate focusing lens (30) pie shaped sector because the lasers (11) and collimating lenses (21) are arranged linearly rather than being arranged about a circular axis (PO Resp. at 37–42), we do not agree. Claim 1 requires “focusing means having n separate radial sectors on its surface, and each of said n collimated beams passes through a separate one of said n sectors of said focusing means” (Ex. 1001, 5:34–37), claim 2 requires “four lasers and four collimating lenses are each formed in a two-dimensional, two by two array [centered on the focal axis of lens 30], wherein said focusing means is a single focusing lens, and wherein each radial sector is a pie-shaped quadrant” (id. at 5:41–44), and claim 7 requires “focusing means having four separate quadrants on its surface, and each of said four collimated beams passes through a separate one of said quadrants of said focusing means” (id. at 6:35–38). Kurita meets those claim requirements. Kurita’s two by two array (10A) of lasers (11), collimating lens (21) array (20), and focusing lens (30) are shown in Kurita’s Figure 3 (cropped) as follows: The image is a portion of Kurita’s Figure 3 showing Kurita’s laser array, collimating lens array, and focusing lens (30). Relative to a point at the center of the laser array (10A) or the collimating lens array (20), each laser (11) and each collimating lens (21) is in a separate quadrant that can be a quadrant of a circle (pie-shape) on lens 30 (Reply 12– 13, Ex. 1003 ¶¶ 85–91).” slip op. at 23

  Patent outcomesUS 7,198,416 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 7,198,416
• Samsung Electronics Co., Ltd. / Apple Inc. v. RJ Technology LLCSome claims unpatentable
  PTAB · Jan 17, 2025 · IPR2024-00597 · APJ Jon B Tornquist · IPR · Final written decision

  Claims 2–4 and 6–18 are unpatentable as obvious over Abe and Guyomard, with claims 9–10 also obvious over Iwaizono; claims 1 and 5 were not shown unpatentable.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art “would have had a Master’s degree in material science, chemical engineering, chemistry, or similar field with four years of experience designing testing, and building secondary lithium batteries.” Pet. 11 (citing Ex. 1002 ¶ 51). Petitioner further contends that a person of ordinary skill in the art would have been aware of “(1) positive electrode materials, (2) negative electrode materials, (3) separators, (4) electrolytes, (5) charge-discharge parameters, and (6) protection circuits, as well as ‘battery failure modes’ such as plating and the formation of dendrites.” Id. (citing Ex. 1002 ¶¶ 50–51). Patent Owner “does not dispute Petitioner’s level of ordinary skill.” PO Resp. 17. Upon review of the prior art of record and the parties’ arguments, we adopt Petitioner’s unopposed definition of the person of ordinary skill in the art as it is consistent with the disclosures of the ’641 patent and the prior art of record.” slip op. at 9

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed board ownDecided for petitioner

    “We also agree with Patent Owner that the charge cut-off voltage is not necessarily the applied voltage during charging. PO Resp. 20. Rather, depending on the charging protocol used and when in the charging cycle the voltage is applied, the applied voltage could be higher than the battery voltage. Ex. 2013; Ex. 2006 ¶ 91. For example, as discussed in more detail below with respect to the Uemura grounds, when fast charging using constant current is used and the charging rate is not slow, the applied voltage will be higher than the battery voltage when the constant current charging phase is stopped. Ex. 2006 ¶ 91; Ex. 2013. Likewise, during constant current/constant voltage charging, the applied voltage approximates the battery voltage only when the battery is nearly completely charged. Ex. 2013; Ex. 2006 ¶ 91. Thus, the applied voltage may be, but is not necessarily, the charge cut-off voltage. In view of the foregoing, we construe “charge cut-off voltage” in claims 1 and 5 as “the maximum value to which the battery is configured to be charged.” PO Resp. 18; Ex. 2008, 217:6–11; Pet. Reply 5. Contrary to Patent Owner’s arguments, however, we do not understand the phrase “configured to be charged” to necessarily represent a single voltage for the battery that is determined based on the structure and chemistry of the battery. Pet. Reply 4–5. Rather, the charge cut-off voltage is a selected potential, or voltage, of the battery or cell at the end of charging that is controlled by a circuit or device, such as a charger or control circuit within the battery. Ex. 1001, 9:50–55; Ex. 1048, 2, 7–8; Ex. 1008, 3:9–13. And, for the reasons discussed herein, the charge cut-off voltage may be, but is not necessarily, the same as the applied voltage during charging. PO Resp. 20.” slip op. at 15

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “charge cut-off voltage “greater than 4.2 V but less than 5.8 V” and calculating a specific or theoretic capacity “with a charge cut-off voltage limited to 4.2” (claim 1) or “with a charge cut-off voltage set at 4.2 V” (claim 5). Ex. 1001, 16:56–61, 17:6–11. Although the parties dispute the precise scope of these claim terms, the parties agree that the first use of “charge cut-off voltage” in claims 1 and 5 refers to the potential of the battery as a whole (between the cathode and the anode), and not a half-cell voltage using lithium metal as a counter electrode.10 Tr. 17:1–3 (agreeing 10 With respect to the phrase “as calculated by a theoretic capacity with a charge cut-off voltage set at 4.2 V,” the parties in fact appear to be in that the first use of “charge cut-off voltage” in claim 5 refers to a full-cell voltage); Sur-reply 5; PO Resp. 22. We need not further construe the claims to resolve the disputes between the parties. See Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (“[O]nly those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy.”)).” slip op. at 16

  • Expert testimonyPatent owner expert creditedDecided for patent owner

    “Given Mr. Juzkow’s unambiguous testimony that Uemura uses constant current charging that would stop when the applied voltage reached 11 The chart is reproduced from SAFT, Charging your lithium-ion batteries: 5 expert tips for a longer lifespan, (https://www.saft.com/energizing-iot/charging-your-lithium-ion-batteries-5-expert-tips-longerlifespan#:~: text=When%20the%20battery%20provides%20current,This%20restore s%20the%20battery's%20capacity). 4.3 V, as well as Dr. Yao’s persuasive testimony that Uemura’s constant charging rate is not slow, we credit the testimony of Dr. Yao that one of ordinary skill in the art would have understood that the internal voltage to which the battery of Uemura was charged is less than 4.3 V. Ex. 2006 ¶ 119. In particular, Dr. Yao persuasively testifies that one of ordinary skill in the art would have believed that the charge cut-off voltage was no more than 4.2 V, and most likely equal to “about 4 V.” Id. ¶¶ 119–122.” slip op. at 21

  Patent outcomesUS 7,749,641 mixed
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 7,749,641

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.