• Uatp IP LLC v. Slick Slide LLCSome claims unpatentable
  PTAB · Oct 2, 2026 · PGR2024-00054 · APJ Brian D Range · PGR · Final written decision

  Claims 22–26 are unpatentable based on obviousness; claims 1–17, 27, and 28 were not shown unpatentable. Patent Owner’s motion to terminate was denied.

  RulingsFinal written decision

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed board ownDecided for patent owner

    “1. Mesh Layer Petitioner contends “no formal claim construction is necessary in this” slip op. at 13

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

    “5. Analysis On this complete record, we determine that Petitioner’s arguments do” slip op. at 31

  • Obviousness (§103) › Graham factors (scope of art, differences, level of skill)Not shown unpatentableNot shown unpatentable

    “form of nylon and some form of Teflon (and possible combinations thereof) having the specific coefficient of friction range given in limitation [1c] breaks down, because the building blocks of the obviousness argument are not sufficiently identified in Phillips alone, nor in the supporting testimony. Accordingly, we determine that Petitioner’s arguments and evidence fail to show that Phillips renders the challenged claims obvious. 6. Conclusion Based on the foregoing, we determine that Petitioner has not established by a preponderance of the evidence that claims 1–4, 6, and 7 would have been anticipated by or obvious in view of Phillips.” slip op. at 33

  • Obviousness (§103) › Objective indicia / secondary considerations › NexusObjective indicia no nexusDecided for petitioner

    “2. Products and Nexus We first consider the issue of whether certain evidence relied upon by” slip op. at 20

  Patent outcomesUS 11,998,854 mixed
  Claim construction§ 102 anticipation§ 103 obviousness§ 112 disclosurecites Phillips · Graham · Nautilus
  Patents in suitUS 11,998,854
• Posco Co., Ltd. v. ArcelormittalAll claims unpatentable
  PTAB · Jul 16, 2026 · IPR2025-00371 · APJ Brian D Range · IPR · Final written decision

  Claims 1–25 are unpatentable as obvious under § 103 over the asserted combinations of Takagi, Cornette, Suehiro, GMW14400, Laurent, and Vaissiere.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art (POSITA) “would have had an undergraduate degree in materials science, manufacturing engineering, mechanical engineering, or equivalent knowledge, training, or experience, with two years of experience working in metallurgy.” Pet. 6 (citing Ex. 1003 ¶ 15). Patent Owner does not challenge Petitioner’s definition of a POSITA for this proceeding. PO Resp. 8. Because the parties agree and because Petitioner’s proposal is reasonable and consistent with the ’227 patent specification and the prior art, we adopt Petitioner’s proposal. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art).” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITAPlain and ordinary meaningDecided for patent owner

    “1. superficial layer The only independent claim at issue, claim 1, recites a “Superficial layer.” Ex. 1001, 15:6. Patent Owner argues that, based on plain and ordinary meaning, the term “superficial layer” refers to a “surface layer” or “top layer.” PO Resp. 8–9. Petitioner does not dispute this construction. See Pet. Reply 21–22 (arguing that the relevant layer of the Suehiro reference is a superficial layer because it is outermost and present at the surface). Because the parties are in agreement and because that agreement is consistent with plain language, claim language, and the ’227 specification, we construe “superficial layer” as referring to a surface layer or top layer.” slip op. at 10

  • Claim Construction › Extrinsic evidence (dictionaries, experts)Term construed petitioner constructionDecided for petitioner

    “defined stoichiometry” (Ex. 2037, 527) but the word may also be a “generic term for phases . . . which may have a narrow or extended compositional stability range” (id.). The first glossary meaning is consistent with Patent Owner’s position. The second, broader, glossary meaning is consistent with Petitioner’s position. Some of the extrinsic sources before us support the broad definition, and some support the narrow definition. See PO Sur-Reply 3–4 (arguing that Dr. Miles admitted that various treatises distinguish intermetallic compounds from alloys and solid solutions). Thus, neither Dr. Miles or Dr. Raabe is “wrong scientifically” in how they use the term “intermetallic” in this proceeding. Id. at 2 (noting that Dr. Miles agreed that Dr. Raabe’s construction is not wrong scientifically). As explained below, however, only one of these meanings is appropriate here. To decide which possible meaning applies to the ’227 patent, we focus on the patent claims and specification. Claim 1 indicates that the intermetallic layer has a “mean composition” (emphasis added). Ex. 1001, 15:1–10. This indicates, albeit weakly, that iron composition across the layer may vary rather than having ordered stoichiometry—consistent with Petitioner’s position. The specification also indicates that “intermetallic alloying” is a possibility—again, consistent with Petitioner’s position. Ex. 1001, 2:47–50. Meanwhile, nothing in the ’227 specification explicitly (or implicitly) suggests that “intermetallic layer” must be limited to elements atomically joined with defined stoichiometry in an ordered crystal structure. We also find that Dr. Miles’s testimony regarding the meaning of “intermetallic” is more credible than Dr. Rabbe’s testimony. Dr. Rabbe, in deposition, stated that Figure 2 of the challenged patent “does not show a layer that meets [his] construction of intermetallic.” Ex. 1078, 129:21–24. The ’227 patent, however, states that Figure 2 includes an “Al-rich Intermetallic layer.” Ex. 1001, Fig. 2, 3:60–64 (“FIG 2. Illustrates a coating … which does not correspond to the invention. This succession of layers (interdiffusion layer and intermetallic layer) yields inferior results in resistance spot welding.”). Also, Dr. Raabe previously referred to a layer of Takagi as having “intermetallic phase layering and structure.” Pet. Reply 4 (citing Ex. 1076 ¶ 166; Ex ¶ 1075, 17) (emphasis omitted). Thus, Dr. Raabe’s construction of “intermetallic” for this proceeding does not fully account for the ’227 patent usage of the word “intermetallic” and does not fully account for Dr. Raabe’s prior usage of the word “intermetallic.” Patent Owner argues that Petitioner’s construction “erases the meaningful distinction” between the claimed layers. PO Resp. 11. Patent Owner further argues that Petitioner’s construction renders the word “intermetallic” superfluous because allowing the intermetallic layer to be “merely a multi-element alloy erases the meaningful distinction among these layers.” Id. We disagree. The word intermetallic serves to require that the layer be composed of two or more metals or a metal and a metalloid. The word intermetallic also serves as a label to differentiate each of the four claimed layers. For example, in claim 1, the word “intermetallic” is used much like the words “interdiffusion” and “intermediate” to give each of the four layers (each having differently mean compositions) different labels.” slip op. at 16

  • Novelty / Anticipation (§102) › Prior-art status of a reference › Printed publication / public accessibilityPrinted publication establishedDecided for petitioner

    “Because IHS was a company that created an online database with the purpose of providing (selling) standards including General Motors standards to the public, we determine that a person of ordinary skill in the art would have known to look to this database and would have been able to find GMW14400. Patent Owner presents no evidence to the contrary. Because a preponderance of the evidence supports Petitioner, we determine Petitioner establishes GMW14400 is qualifies as prior art.” slip op. at 21

  Patent outcomesUS 11,326,227 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 11,326,227
• Posco Co., Ltd. v. ArcelormittalAll claims unpatentable
  PTAB · Jul 16, 2026 · IPR2025-00370 · APJ Brian D Range · IPR · Final written decision

  Claims 1–30 are unpatentable as obvious under § 103 over the asserted combinations of prior art.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art (POSITA) “would have had an undergraduate degree in materials science, manufacturing engineering, mechanical engineering, or equivalent knowledge, training, or experience, with two years of experience working in metallurgy.” Pet. 6 (citing Ex. 1003 ¶¶ 13–16). Patent Owner does not challenge Petitioner’s definition of a POSITA for this proceeding. PO Resp. 8. Because the parties agree and because Petitioner’s proposal is reasonable and consistent with the ’602 patent specification and the prior art, we adopt Petitioner’s proposal. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (the prior art may reflect an appropriate level of skill in the art).” slip op. at 8

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededDecided for patent owner

    “1. superficial layer All independent claims at issue, claims 1, 21, and 24, recite a “superficial layer.” Ex. 1001, 15:11, 16:60, 17:21. Patent Owner argues that, based on plain and ordinary meaning, the term “superficial layer” refers to a “surface layer” or “top layer.” PO Resp. 8–9. Petitioner does not dispute this construction. See Pet. Reply 21–22 (arguing that the relevant layer of the Suehiro reference is a superficial layer because it is outermost and present at the surface). Because the parties are in agreement and because that agreement is consistent with plain language, claim language, and the ’602 specification, we construe “superficial layer” as referring to a surface layer or top layer.” slip op. at 10

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “defined stoichiometry” (Ex. 2037, 527) but the word may also be a “generic term for phases . . . which may have a narrow or extended compositional stability range” (id.). The first glossary meaning is consistent with Patent Owner’s position. The second, broader, glossary meaning is consistent with Petitioner’s position. Some of the sources before us support the broad definition, and some support the narrow definition. See PO Sur-Reply 3–4 (arguing that Dr. Miles admitted that various treatises distinguish intermetallic compounds from alloys and solid solutions) Thus, neither Dr. Miles or Dr. Raabe is “wrong scientifically” in how they use the term “intermetallic” in this proceeding. Id. at 2 (noting that Dr. Miles agreed that Dr. Raabe’s construction is not wrong scientifically). As explained below, however, only one of these meanings is appropriate here. To decide which possible meaning applies to the ’602 patent, we focus on the patent claims and specification. The claims indicate that the intermetallic layer has a “mean iron composition” (emphasis added). Ex. 1001, 15:6–10. This indicates, albeit weakly, that the iron composition across the layer may vary rather than having ordered stoichiometry— consistent with Petitioner’s position. The specification also indicates that “intermetallic alloying” is a possibility—again, consistent with Petitioner’s position. Id. at 2:50–54. Meanwhile, nothing in the ’602 specification explicitly (or implicitly) suggests that “intermetallic layer” must be limited to elements atomically joined with defined stoichiometry in an ordered crystal structure. We also find that Dr. Miles’s testimony regarding the meaning of “intermetallic” is more credible than Dr. Raabe’s testimony. Dr. Raabe, in deposition, stated that Figure 2 of the challenged patent “does not show a layer that meets [his] construction of intermetallic.” Ex. 1078, 129:21–24. The ’602 patent, however, states that Figure 2 includes an “Al-rich Intermetallic layer.” Ex. 1001, Fig. 2, 3:57–61 (“FIG 2. Illustrates a coating . . . which does not correspond to the invention. This succession of layers (interdiffusion layer and intermetallic layer) yields inferior results in resistance spot welding.”). Also, Dr. Raabe previously referred to a layer of Takagi as having “intermetallic phase layering and structure.” Pet. Reply 4 (citing Ex. 1076, 166; Ex. 1075, 17) (emphasis omitted). Thus, Dr. Raabe’s definition of “intermetallic” does not fully account for the ’602 patent usage of the word “intermetallic” and does not fully account for Dr. Raabe’s prior usage of the word “intermetallic.” Patent Owner argues that Petitioner’s construction “erases the meaningful distinction” between the claimed layers. PO Resp. 11. Patent Owner further argues that Petitioner’s construction renders the word “intermetallic” superfluous because allowing the intermetallic layer to be “merely a multi-element alloy erases the meaningful distinction among these layers.” Id. We disagree. The word intermetallic serves to require that the layer be composed of two or more metals or a metal and a metalloid. The word intermetallic also serves as a label to differentiate each of the four claimed layers. For example, in claim 1, the word “intermetallic” is used much like the words “interdiffusion” and “intermediate” to give each of the four layers (each having differently defined mean iron compositions) different labels.” slip op. at 16

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundDecided for petitioner

    “have had reason to combine teachings of Takagi and Cornette with a reasonable expectation of success. Pet. 11–20 (citing, e.g., Ex. 1003 ¶¶ 28– 42; Ex. 1016 ¶ 35; Ex. 1014, 9; Ex. 1025, 5:17–20; Ex. 1026, 7; Ex. 1034 ¶ 13). In particular, Petitioner argues that Takagi discloses a pre-coating thickness of 10–20 µm but does not explicitly disclose a post hot-stamping coating thickness corresponding to the pre-coating thickness. Pet. 11. Cornette teaches that the hot-stamping thickness causes coating expansion from 25 µm to about 40 µm, an increase of 60%. Id. (citations omitted). Petitioner and Dr. Miles reason that, when hot stamping Takagi’s product, the thickness would be 32 µm. Id. (citing Ex. 1003 ¶ 32); see also Pet. Reply 20–21. Thus, Patent Owner argues that Cornette evidences Takagi’s finally coating thickness without requiring modification of Takagi. Petitioner further argues that Takagi and Cornette teach that post hot- stamping thickness could be varied and optimized as a result effective variable. Id. at 12–13; see also Pet. Reply 17–18. Cornette teaches, for example, that “[t]he average [pre-coating] layer thickness showing the best compromise between corrosion protection and weldability is 25 µm” and links this pre-coating thickness to a final thickness of “about 40 µm at the steel surface.” Ex. 1014, 9. Petitioner also argues that it would have been obvious to fill in other details of Takagi including, for example, selecting USIBOR 1500 steel, based on the teachings of Cornette. Pet. 14. Patent Owner argues that there is no reason to combine Takagi with the teachings of Cornette. PO Resp. 26. Patent Owner makes seven related arguments. Patent Owner first argues that the Petitioner’s position is speculative and lacks basis. Id. at 26–27. We disagree. Cornette evidences a final coating thickness for Takagi, and the references also suggest that final coating thickness is result effective. Second, Patent Owner argues that there would have been no incentive to seek a motivation to seek a thicker coating post-hot stamping. Id. at 28– 35. This argument does not undermine Petitioner’s position that Takagi, by itself, would have reached a thicker coating after stamping as evidenced by Cornette. Pet. 11–12. Petitioner takes the position, with evidence, that practice of Takagi alone would reach the recited thickness. No motivation to modify Takagi is required under this position.” slip op. at 25

  Patent outcomesUS 10,961,602 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites KSR · Graham
  Patents in suitUS 10,961,602
• First Quality Retail Services, LLC / First Quality Consumer Products, LLC et al. v. Essity Hygiene And Health ABAll claims unpatentable
  PTAB · May 12, 2026 · IPR2024-01487 · APJ Kristina M Kalan · IPR · Final written decision

  Claims 1–5, 7, 8, 20–22, 24, and 25 are unpatentable, based on anticipation by Bergstrom and obviousness over the stated combinations.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “In the Institution Decision, we adopted Petitioner’s definition. Dec. 9–10. In its Response, Patent Owner cites to Petitioner’s definition and states that Patent Owner “applies Petitioners’ definition.” PO Resp. 7. Because Petitioner’s definition of the level of skill in the art is consistent with the ’138 patent and the asserted prior art, we maintain it for purposes of this Final Written Decision. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001).” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)Term construed board ownDecided for petitioner

    “We begin our analysis with the language of the claims. Phillips, 415 F.3d at 1312; see also SuperGuide Corp. v. DirecTV Enterprises, Inc., 358 F.3d 870, 874–875 (Fed. Cir. 2004) (“There is a ‘heavy presumption’ that the terms used in the claims ‘mean what they say and have the ordinary meaning that would be attributed to those words by persons skilled in the relevant art.’”). Claim 1 recites, in relevant part, “said fluid flow control structure being a layered structure comprising a non-perforated fibrous polymeric layer and a first perforated polymeric layer.” Ex. 1001, 13:62–64 (limitation [1h]). The plain language of claim 1 does not address additional properties of the perforated polymeric layer; the language of the dependent claims, however, imposes additional limitations on the properties of the perforated polymeric layer such as a particular basis weight (claim 2), a particular makeup (claim 3), a particular aperture size (claim 7), a particular open area (claim 8), and that it “is a three-dimensionally formed layer having penetrating apertures extending from a first surface of the first perforated polymeric layer towards a second surface of the first perforated polymeric layer and forming protrusions on said second surface” (claim 4). The dependent claims’ additional language indicates that the term “perforated” within the term “perforated polymeric layer” in claim 1 is not limited in the manner asserted by Patent Owner’s proposed construction.” slip op. at 12

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)UnpatentableUnpatentable

    “layer pierced through with holes or apertures,” we are persuaded that Petitioner meets its burden as to this limitation. Petitioner argues that under our construction, Bergstrom’s express disclosure of forming element 60, and Bergstrom’s explanation of the properties of forming element 60, meets the claimed “perforated polymeric layer” limitation. Pet. 38–41 (citing Ex. 1002 ¶¶ 114–117). Even under Patent Owner’s proposed construction, Petitioner argues, forming element 60 would also allow free flow of liquid bodily waste. Pet. Reply 3– 4 (citing Ex. 1021 ¶¶ 20–23). Importantly, Bergstrom expressly discloses: “suitable materials for the forming element 60 are plastic films, perforated plastic films and reinforced tissue or reinforced nonwoven materials.” Ex. 1004, 10:1–4. This express disclosure is clear. Even though the forming element 60 in Bergstrom might be “typically” liquid-impermeable (Ex. 1004, 9:24–30), that does not preclude a layer that is perforated, particularly where Bergstrom expressly discloses a perforated plastic film as one of the possibilities for forming element 60. Ex. 1004, 10:1–4. Additionally, although Patent Owner focuses on Bergstrom’s disclosure that forming element 60 is “typically liquid-impermeable” (PO Resp. 58–60; Ex. 1004, 9:24–30), we do not view Bergstrom’s use of the word “typically” as mandating that the forming element always be liquid impermeable. We agree that the word “typically” does not mean “always” and that such a reading would render “typically” superfluous. Pet. Reply. 5. We do not find any ambiguity in Bergstrom’s disclosure regarding possible use of perforated plastic films for its forming element 60; whether or not the forming element 60 provides other functions (like stiffness) does not dictate whether it may also be perforated, or be part of a fluid flow control structure. On this point, we credit Petitioner’s arguments and explanation, as supported by Dr. Pourdeyhimi’s testimony. Pet. Reply 6–7; Ex. 1021 ¶ 27–28 (“components of absorbent articles could be multifunctional”).” slip op. at 20

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “from the start” (PO Resp. 29), and that “using all or part of [Glaug’s] fluid-acquisition system in place of [Nakazawa’s] diffusion sheet would be antithetical to the teachings of both references” (id. at 35), we agree that the proposed combination of Nakazawa’s structure with the layers of Glaug is sufficiently motivated and reasonably expected to result in a successful article, for the reasons articulated by Petitioner. See, e.g., Pet. 59–65; Ex. 1002 ¶¶ 176–192. Namely, although fluid may flow in both Z directions in Nakazawa (PO Resp. 30), that does not foreclose the combination with Glaug in the manner proposed by Petitioner. See generally Ex. 1002 ¶¶ 176–192; see id. ¶ 184 (detailing the mechanics of the proposed combinations), ¶¶ 188–191 (discussing motivation to combine), ¶ 192 (discussing reasonable expectation of success). The combination can be achieved “either by adding the lower acquisition layer 64 [of Glaug] to diffusion sheet 63 [of Nakazawa], or by replacing diffusion sheet 63 [of Nakazawa] with the two-layer fluid acquisition system 34 [of Glaug],” and as persuasively explained by Dr. Pourdeyhimi, the arrangement constitutes a “fluid flow control structure.” See Ex. 1021 ¶¶ 45–47. Additionally, the diffusion sheet in Nakazawa can be made from the same material as used in Glaug, namely, AquiDry™. Id. ¶¶ 53–55; see also Tr. 17:25–18:3 (“although Glaug does not specify the name AquiDry in its disclosure, Patent Owner’s expert testified that it’s his understanding that Glaug is discussing the AquiDry material, the same material that is in Nakazawa . . . . they disclose using the same material, and Nakazawa says this material work[s]”). When asked if Patent Owner’s expert had any concerns that AquiDry was not the same as between Nakazawa and Glaug, Patent Owner’s counsel replied “They are the same, Your Honor. And we embrace that.” Tr. 46:8–12; see also id. at 58:19 (Petitioner’s counsel commenting about Patent Owner’s counsel: “they agree, AquiDry is used in both Nakazawa and Glaug”). Thus, Patent Owner’s argument that Nakazawa’s diffusion sheet and Glaug’s fluid acquisition layer have different purposes because Nakazawa’s diffusion sheet allegedly must promote fluid flow in the Z-directions, both toward and away from the body (PO Resp. 29–37; Ex. 2004 ¶¶ 26–28, 30– 35)) is not clearly supported by Nakazawa, and is also contravened by the shared disclosure of Nakazawa and Glaug as to the composition of the disputed layer. We have reviewed the complete record, including Patent Owner’s and Mr. Sheldon’s assertions that Nakazawa requires promoting fluid flow in both Z-directions (see id.), but find that Petitioner carries its burden to demonstrate that one of ordinary skill in the art would have been motivated to combine Nakazawa and Glaug with a reasonable expectation of success. On this complete record, Petitioner explains sufficiently why and how a person of ordinary skill would modify Nakazawa’s diffusion sheet, i.e., to use Glaug’s fluid acquisition system, or the lower non-perforated layer of its fluid acquisition system, in Nakazawa, and Petitioner provides well-supported reasons for doing so.” slip op. at 36

  Patent outcomesUS 9,308,138 unpatentable
  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,308,138
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00187 · APJ Debra L Dennett · IPR · Final written decision

  Claims 1–17 are unpatentable under § 103, principally because Chang in view of Jin renders them obvious; the Jin/Feldmann grounds were not shown.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49).” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11

  • Expert testimonyPatent owner expert creditedDecided for patent owner

    “gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard. Without an apparent reason to modify the teachings of Jin and Feldmann to” slip op. at 19

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 17

  Patent outcomesUS 10,230,009 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,230,009
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00006 · APJ Debra L Dennett · IPR · Final written decision

  Claims 1–17 are unpatentable under § 103, principally over Chang and Jin; the Board rejected the Jin and Feldmann combinations for lack of a reason to combine.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “In light of the record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’009 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’009 patent and the prior art.” slip op. at 10

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 24. Patent Owner does not address claim construction. See generally Resp.; Sur-reply. For purposes of this Decision, we need not expressly construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 11

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 26. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 116 with Pet. 26). Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” See Magnum, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 116 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001 ¶ 159. Neither Petitioner nor Dr. Banerjee address or dispute this testimony. See generally Reply; Ex. 1037. We credit Dr. Peckerar’s testimony in this regard.” slip op. at 19

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” Resp. 42 (citing Ex. 1013 ¶ 76). In so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Id. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Chang ¶ 62; Tr. 15:20–17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 73, 217 (citing Ex. 1023 § 1). Chang also discloses that the emitter area may be formed by thermal diffusion, ion implantation or the like. Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding a tunneling layer and a base surface field area from periphery region and isolation region. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” slip op. at 32

  Patent outcomesUS 10,230,009 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,230,009
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00918 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board rejected the Jin and Feldmann based grounds for lack of a reason to combine without hindsight.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successUnpatentableMotivation foundUnpatentable

    “Patent Owner focuses on Chang’s description in paragraph 76 of a single configuration in which the emitter area and back surface field area are not adjacent to each other, thus eliminating “the necessity of performing an isolation process when the emitter area [] and the back surface field are [] are formed to be adjacent to each other.” PO Resp. 42–43 (citing Ex. 1013 ¶ 76). But, in so doing, Patent Owner side steps Chang’s unambiguous definition that “‘entirely formed’ means that an element such as a layer is formed over an entire surface without an empty area or a non-coverage area, or is formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62 (emphasis added). Chang discloses that a first tunneling layer, a first portion of an emitter area, a second tunneling layer, and a back surface field area may each be “formed over an entire area excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like.” Ex. 1013 ¶¶ 45, 51, 56, 62. Chang’s definition of “entirely formed” (“excluding pre-designated or inevitably formed regions such as periphery region, isolation region or the like”) implies use of a mask. See Ex. 1013 ¶ 62; Tr. 15:20– 17:11. Dr. Banerjee testifies that the need to electrically isolate the emitter region from the back surface field was well known in the field, and both Chang and Jin teach backside isolation regions. Ex. 1003 ¶¶ 70–81, 91–96, 200 (citing Ex. 1026 § 1 and stating that “[b]oth Chang and Jin likewise teach backside isolation regions”). Chang also discloses that the emitter area may be formed by “thermal diffusion, ion implantation or the like.” Ex. 1013 ¶ 98. Petitioner persuasively argues that Chang’s disclosure of thermal diffusion of the emitter layer would result in dopants diffused into not only the top surface of the substrate, but also the exposed lateral surfaces, a problem also noted in Jin. See Pet. 11–12; Pet. Reply 6–7; Ex. 1003 ¶ 71; Ex. 1009 ¶¶ 57–58. Jin discloses avoiding shorting of the emitter layer and back surface field layer by edge isolation on the back surface field layer using a mask to create a “gap-T.” Ex. 1009 ¶¶ 57–58, 83. Chang discloses excluding the second tunneling layer and a base surface field area from periphery region and isolation portion. Ex. 1013 ¶¶ 56, 62. Using a mask, as implied in Chang and explicitly disclosed in Jin, would “pre-designate” and/or “inevitably form” the regions where the tunneling layer and back surface field area are excluded. We credit Dr. Banerjee’s testimony that one of ordinary skill in the art “reviewing Chang would therefore understand the importance of implementing the isolation region in Chang’s device, and would therefore be motivated to look to other references, such as Jin (which was assigned to the same original assignee as Chang, LG Electronics, EX1009-Jin, face; EX1013-Chang, face) to understand details regarding Chang’s isolation region.” Ex. 1003 ¶ 201.” slip op. at 33

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00186 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under § 103 over Chang and Jin; the Board found the combination disclosed the claimed isolation portion and supported the challenged claims.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededNot reached

    “C. Claim Construction We construe claim terms according to the standard set forth in Phillips v. AWH Corp., 415 F.3d 1303, 1312–17 (Fed. Cir. 2005) (en banc); 37 C.F.R. § 42.100(b). Under Phillips, we give claim terms “their ordinary and customary meaning.” Phillips, 415 F.3d at 1312. “[T]he ordinary and customary meaning of a claim term is the meaning that the term would have to a person of ordinary skill in the art in question at the time of the invention.” Id. at 1313. “Importantly, the person of ordinary skill in the art is deemed to read the claim term not only in the context of the particular claim in which the disputed term appears, but in the context of the entire patent, including the specification.” Id. Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Expert testimonyPetitioner expert discountedPatent owner expert creditedMixed

    “edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide. Ex. 2001 ¶ 152 (referring to Ex. 2001 ¶¶ 149–151). Moreover, Dr. Peckerar testifies that “Dr. Banerjee also appears to be arguing that incorporation of impurities into the oxide will produce a MOSFET-like structure, with the contaminated oxide acting as a MOS gate leading to enhanced leakage,” but, for that to occur, “the source and drain areas would need to be of the same type.” Ex. 2001 ¶ 159. Here however, “the tunnel oxide layer is located between an n-type polysilicon layer and p-type frontside emitter layer” so “[n]o MOSFET-like structure can form because the source and drain are of different types.” Ex. 2001” slip op. at 18

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightNot shown unpatentableMotivation not foundNot shown unpatentable

    “base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• Runergy Alabama Inc. / Runergy USA Inc. et al. v. Trina Solar Co., Ltd.All claims unpatentable
  PTAB · Apr 15, 2026 · IPR2025-00007 · APJ Avelyn M Ross · IPR · Final written decision

  Claims 1–11 are unpatentable under §103 over Chang and Jin because the combination teaches the claimed isolation portion and the claimed tapering.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedOther

    “Petitioner contends that a person of ordinary skill in the art would have been someone with an advanced degree involving the disciplines of electrical engineering, applied physics, chemistry, or materials science, and at least two years of experience designing, developing, or researching in the field. Alternatively, that person would have had a bachelor’s degree in electrical engineering, applied physics, or materials science, and at least three years of experience designing, developing, or researching in the field. Pet. 4 (citing Ex. 1003 ¶ 49). Patent Owner does not address the level of ordinary skill in the art. See generally PO Resp; Sur-reply. In light of the complete trial record before us, we adopt Petitioner’s proposal regarding the level of ordinary skill in the art. Based on our review of the ’104 patent and the prior art of record, we determine that the definition offered by Petitioner comports with the qualifications a person would have needed to understand the ’104 patent and the prior art.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner contends that “[n]o claim construction is believed to be necessary to resolve this Petition.” Pet. 23. And, Patent Owner does not address claim construction. See generally PO Resp. As neither party proposes an express construction for our consideration and because we determine that an express claim construction is not necessary for us to render a decision in this matter, we do not construe any claim terms. See Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999) (holding that “only those terms need be construed that are in controversy, and only to the extent necessary to resolve the controversy”); see also Nidec Motor Corp. v. Zhongshan Broad Ocean Motor Co., 868 F.3d 1013, 1017 (Fed. Cir. 2017) (citing Vivid Techs. in the context of an inter partes review).” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of success › HindsightTeaching away not foundNot shown unpatentable

    “On this complete trial record, we agree with Patent Owner. It is improper to base a conclusion of obviousness upon facts gleaned only through hindsight. “The invention must be viewed not after the blueprint has been drawn by the inventor, but as it would have been perceived in the state of the art that existed at the time the invention was made.” Sensonics, Inc. v. Aerosonic Corp., 81 F.3d 1566, 1570 (Fed. Cir. 1996) (citing Interconnect Planning Corp. v. Feil, 774 F.2d 1132, 1138 (Fed. Cir. 1985)). Therefore, “to establish a prima facie case of obviousness based on a combination of elements disclosed in the prior art, the [Petitioner] must articulate the basis on which it concludes that it would have been obvious to make the claimed invention.” Id. Impermissible hindsight is inferred when the specific understanding or principle within the knowledge of one of ordinary skill in the art that would motivate one (with no knowledge of the claimed invention) to make the proposed combination has not been explained. In re Rouffet, 149 F.3d 1350, 1358 (Fed. Cir. 1998).” slip op. at 16

  • Expert testimonyPatent owner expert creditedPetitioner expert discountedDecided for patent owner

    “However, Petitioner proposes to remove the tunnel oxide layer from the edge and offers little explanation of why the skilled artisan would apply Jin’s gap- T isolation region to both of Feldmann’s polysilicon and tunnel oxide layers. As noted above, Petitioner states that the skilled artisan would have included Jin’s gap-T isolation region in order to prevent shorting. Pet. 25. Petitioner’s reasoning is questionable—supported only by the conclusory testimony of Dr. Banerjee. Dr. Banerjee’s testimony offers no more evidentiary support than provided in the Petition. Compare Ex. 1003 ¶ 113, with Pet. 25. Petitioner cannot satisfy its burden of proving obviousness by employing “mere conclusory statements.” Magnum Oil, 829 F.3d at 1380. We acknowledge Dr. Banerjee’s testimony that the combination of Jin’s gap-T isolation region would prevent shorting and that extending the tunnel oxide layer the edge “could trap impurities and create negative fixed oxide charges, which could then create a p-type inversion in the n-type base substrate, leading to a leakage path to the p-type emitter on the front of the solar cell” (Ex. 1003 ¶ 113 (emphasis added)) but are not convinced by his equivocal testimony. Notably too, neither Jin nor Feldmann discuss issues relating to trapped impurities and Petitioner, as well as Dr. Banerjee, fail to direct our attention to any record evidence to support their contentions. Rather, we are persuaded by Dr. Peckerar’s testimony that as a general rule in semiconductor process technology, a bare silicon surface should not be left unpassivated after processing. Elemental silicon is highly chemically reactive. As such, the bare surface is a “magnet” for defects and contamination. Leaving the tunnel oxide in place across the entire substrate backside would reduce this problem. Ex. 2001 ¶ 142. Dr. Peckerar further explains that a person of ordinary skill in the art would have known how to avoid shorting and leakage. In particular, he testifies that the manner by which charge is transported through a tunnel oxide can be controlled by adjusting manufacturing parameters such as time, temperature, thickness, and ambient impurities. A POSITA would plainly have adjusted these parameters to ensure that the tunnel oxide operates as intended (i.e., minimizes recombinant losses while transporting charge carriers to the backside of the solar cell) while avoiding undesirable leakage current. Because unwanted leakage charge can be avoided via other means during manufacture, there would have been no reason to reduce the physical extent of the tunnel oxide.” slip op. at 18

  Patent outcomesUS 9,722,104 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,722,104
• R.J. Reynolds Vapor Company v. Healthier Choices Management Corp.All claims unpatentable
  PTAB · Mar 9, 2026 · IPR2024-01458 · APJ Kristina M Kalan · IPR · Final written decision

  Claims 1, 7, 8, and 11 are unpatentable as obvious over Lee-based combinations; the Gilbert-based grounds did not establish unpatentability.

  RulingsFinal written decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Pet. 15 (citing Ex. 1003 ¶ 18). Petitioner further argues a “POSA would have been familiar with electrically powered cigarettes and their components and underlying technologies or similar components and technologies.” Id. “For the purposes of this Response,” Patent Owner “does not dispute Petitioner’s proposed level of skill in the art.” Resp. 17. On this complete record, we adopt Petitioner’s unopposed definition because it appears consistent with the’788 patent and the prior art of record. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (holding that the prior art itself can reflect the appropriate level of ordinary skill in the art).” slip op. at 8

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Patent Owner states that “Petitioner and [Petitioner’s declarant] Mr. Kodama interpret the meaning of the claims based on [Patent Owner’s] construction of the claims by its allegations of infringement in the ongoing litigation.” Resp. 18. Patent Owner further states that for “the purposes of this response,” it “agrees on how the claims are to be construed.” Id. Upon review of the record, we determine that no claim terms require express construction. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999)).” slip op. at 9

  • Expert testimonyPetitioner expert creditedDecided for petitioner

    “the combination of proposed references would operate. As shown in Petitioner’s proposed modification, the Gilbert bulb would have been modified to fit the Lee device. Pet. 57 (annotated Figure); Ex. 1003 ¶ 123 (stating that the combination would work “by merely replacing [Lee’s] heating element (133) with this bulb heater inside of the vaporization unit (14)” and the “bulb heater could be connected to [Lee’s] electric circuit board (111) and battery assembly (11) in a very similar fashion to the nichrome wire heater represented in Lee”); Reply 29–30 (explaining Petitioner’s annotated figure wherein “the fiber rod is not encapsulated inside the bulb”); Ex. 1026 ¶¶ 29–30 (clarifying how the fiber in Petitioner’s proposed combination from its annotated Figure in the Petition extends to, and makes contact with, the outside of the bulb, putting the fluid into direct contact with the bulb; explaining various simple ways a POSA would understand to accomplish this). We credit Petitioner’s proposal and Mr. Kodama’s testimony in this regard. Therefore, we agree that Lee would not have to be “significantly modified or reimagined” as alleged by Patent Owner, nor would the inclusion of a bulb in the Lee device “render Lee inoperable” in view of the modifications to the Gilbert bulb included in Lee, as proposed by Petitioner. Resp. 30–31.” slip op. at 25

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation foundReasonable expectation foundUnpatentable

    “art would not have combined Lee and Gilbert or Levin, particularly with respect to element [1d], we are persuaded by Petitioner’s arguments that one of ordinary skill in the art would have been motivated to make the combination with a reasonable expectation of success. Petitioner states that the motivation to make the combination would have come from issues “with e-cigarettes at the time, such as metallic taste issues or inhalation risks associated with the use of a metal wire heating element,” and would have explored “heat conducting materials that could vaporize the nicotine liquid without making direct contact with the heating wire.” Pet. 57 (citing Ex. 1003 ¶ 117 (discussing the metallic flavor “dry hit” problem)); see also Reply 18–19. Additionally, Petitioner argues that one of ordinary skill in the art would have implemented “a heating element within a glass bulb to increase the life of the heating element and prevent failure of a device.” Id. at 57–58 (citing Ex. 1009 ¶ 4; Ex. 1003 ¶ 119), 59 (a “POSA would have been motivated to implement a heating element within a glass bulb like that described in Levin for all of the reasons described above” in connection with Gilbert). Petitioner depicts one example of how its proposed combination would incorporate the Gilbert bulb into the Lee device. Pet. 57 (citing Ex. 1003 ¶ 118)). Petitioner additionally relies on Levin’s disclosure that using a bulb will “allow for a consistent and reliable heat source” and “achieve a desired operating temperature when compared to conventional devices.” Id. at 59 (citing Ex. 1009 ¶¶ 56, 49). Mr. Kodama also notes the age and ubiquity of bulb heaters, credibly testifying that “a POSA would have been motivated to implement a bulb heater in the Lee device, and, due at least to the ubiquitous nature of such heaters, the implementation of such a heater would have been well within the knowledge and skill of a POSA.” Pet. 59; Reply 20; Ex. 1003 ¶¶ 39–48, 123. Petitioner also provides sufficient explanation as to “how” and “why” the combination of proposed references would operate. As shown in Petitioner’s proposed modification, the Gilbert bulb would have been modified to fit the Lee device. Pet. 57 (annotated Figure); Ex. 1003 ¶ 123 (stating that the combination would work “by merely replacing [Lee’s] heating element (133) with this bulb heater inside of the vaporization unit (14)” and the “bulb heater could be connected to [Lee’s] electric circuit board (111) and battery assembly (11) in a very similar fashion to the nichrome wire heater represented in Lee”); Reply 29–30 (explaining Petitioner’s annotated figure wherein “the fiber rod is not encapsulated inside the bulb”); Ex. 1026 ¶¶ 29–30 (clarifying how the fiber in Petitioner’s proposed combination from its annotated Figure in the Petition extends to, and makes contact with, the outside of the bulb, putting the fluid into direct contact with the bulb; explaining various simple ways a POSA would understand to accomplish this). We credit Petitioner’s proposal and Mr. Kodama’s testimony in this regard. Therefore, we agree that Lee would not have to be “significantly modified or reimagined” as alleged by Patent Owner, nor would the inclusion of a bulb in the Lee device “render Lee inoperable” in view of the modifications to the Gilbert bulb included in Lee, as proposed by Petitioner. Resp. 30–31.” slip op. at 24

  Patent outcomesUS 9,538,788 unpatentable
  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,538,788

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.