• Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing denied
  PTAB · Oct 7, 2025 · IPR2024-01462 · APJ Jo-Anne M Kokoski · IPR · Rehearing

  The Board denied Solus’s rehearing request, leaving institution denied for claims 1–8 because the petition did not adequately show motivation to combine Hanafusa and Dobashi.

  RulingsRehearing decision

  • RehearingRehearing, deniedDenied

    “of the decision de novo, but instead review the decision for an abuse of discretion. 37 C.F.R. § 42.71(c). An abuse of discretion may be determined “if a decision is based on an erroneous interpretation of law, if a factual finding is not supported by substantial evidence, or if the decision represents” slip op. at 2

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable

    “In particular, neither Petitioner nor Dr. Josefowicz adequately explain why a POSITA looking for ways to make Hanafusa’s surface roughness low-profile would look to methods to achieve Dobashi’s RSm values. Dobashi teaches that because RSm “can be adopted as the period of waviness, RSm can also be used as an indicator for judgment of the surface.” Ex. 1005, 2:66–3:1, 6:23–26. Dobashi explains that waviness is “an indicator for determining whether the fine pattern forming performance is good or bad,” and “[t]he surface has small waviness and is smooth when RSm is large, and the surface has large waviness Dobashi also teaches that surface roughness Rzjis is used as a low-profile indicator. Ex. 1005, 2:66–3:1. Dobashi, therefore, teaches that RSm is an indicator of surface waviness, which Dobashi explains is different than surface roughness. Id. at 2:66– 3:3, 6:23–29. Given these teachings in Dobashi, neither Petitioner nor Dr. Josefowicz sufficiently explains how or why a POSITA would have been motivated to implement Dobashi’s RSm values to make Hanafusa’s surface roughness low-profile. See Pet. 10–12; Ex. 1003 ¶¶ 46–52.” slip op. at 4

  § 103 obviousness
  Patents in suitUS 11,346,014
• Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Rehearing denied
  PTAB · Oct 7, 2025 · IPR2024-01461 · APJ Jo-Anne M Kokoski · IPR · Rehearing

  The Board denied rehearing and left in place its denial of institution because Petitioner did not show that claims 1–10 were likely obvious over the asserted combinations.

  RulingsRehearing decision

  • RehearingRehearing, deniedDenied

    “II. STANDARD OF REVIEW When rehearing a decision on institution, we do not review the merits of the decision de novo, but instead review the decision for an abuse of discretion. 37 C.F.R. § 42.71(c). An abuse of discretion may be determined “if a decision is based on an erroneous interpretation of law, if a factual finding is not supported by substantial evidence, or if the decision represents an unreasonable judgment in weighing relevant factors.” Arnold Partnership v. Dudas, 362 F.3d 1338, 1340 (Fed. Cir. 2004) (citing In re 1 US 2013/0108922 A1, published May 2, 2013 (Ex. 1004, “Shinozaki”). 2 G. Khatibi, Temperature Dependent Elastic and Thermal Properties of Thin Copper Foils, Copper; Proceedings of the International Conference Copper ’06 (2006) (Ex. 1006, “Khatibi”). 3 Korean Patent Pub. No. 10-2012-0003485, published Jan. 10, 2012 (Ex. 1013; Ex. 1014 (English translation), “Toshio”). 4 US 2013/0108887 A1, published May 2, 2013 (Ex. 1012, “Kim”). 5 Griesi, M.B., Characterization of Electrodeposited Copper Foil Surface Roughness for Accurate Conductor Power Loss Modeling (2014) (Master’s Thesis, University of South Carolina) (Ex. 1015, “Griesi”). rehearing has the burden to show that the decision should be modified. 37 C.F.R. § 42.71(d). Additionally, the request for rehearing “must specifically identify all matters the party believes the Board misapprehended or overlooked, and the place where each matter was previously addressed in a motion, an opposition, or a reply.” Id.” slip op. at 2

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Not shown unpatentable

    “For example, Dr. Randall does not provide adequate explanation or objective evidence to support his opinion that Khatibi’s use of a laser speckle based dilatometer instead of the claimed thermomechanical analyzer “is unlikely to significantly impact the CTE[6] value” because “variations in equipment and a heating speed of 5° C/min would not significantly alter the results.” Ex. 1003 ¶ 58. In particular, Dr. Randall neither explains what constitutes a “significant” impact on CTE, nor provides objective evidence to support his contention that equipment variations and heating differences would not “significantly alter” the resulting measurements. And although Dr. Randall opines that “the heating rate (5°C per minute) is typical for certain devices” such as a thermomechanical analyzer or dilatometer, and “[t]ypically, these devices use temperature ramp rates between 2°C and 20°C per minutes, so the ‘5° C./min’ recited in [1d] is common and should not drastically affect the measurement results,” Dr. Randall fails to point us to any evidence showing that these temperatures are “typical” or that the claimed heating rate is “common.” Id. ¶ 59 (emphases added).” slip op. at 4

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable

    “Petitioner, however, does not adequately explain why a POSITA would have been motivated to modify Kim’s copper foil surface to have a Pc value of 19.2 as reported in Griesi. In particular, neither Petitioner nor Dr. Randall points us to, nor do we discern, any teaching in Griesi that a peak count of 19.2 provides any particular benefits or properties that would have lead a POSITA to modify Kim’s copper foil surface as Petitioner proposes. Instead, Petitioner’s arguments that a POSITA would have been motivated to modify Kim’s copper foil surface with Griesi’s peak count patent itself. See KSR Int’l Co. v. Teleflex Inc., 550 U.S. 398, 421 (2007) (stating that the fact finder must be aware “of the distortion caused by hindsight bias and must be cautious of arguments reliant upon ex post reasoning”). It was Petitioner’s burden to establish that the combined teachings Kim and Griesi disclose limitation [1g] as proposed. We are not persuaded that we misapprehended Petitioner’s argument when we determined that Petitioner did not meet that burden.” slip op. at 8

  • BurdenDecided for patent owner

    “It was Petitioner’s burden to establish the Khatibi, alone or in combination with Shinozaki, Toshio, and Kim, discloses limitation [1d]. We concluded that Petitioner failed to meet that burden for the reasons explained in our Decision. We are not persuaded that we overlooked or misapprehended Khatibi’s disclosures, or Petitioner’s evidence and explanation thereof, in doing so.7” slip op. at 5

  § 103 obviousnesscites KSR
  Patents in suitUS 10,811,689
• Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Institution denied
  PTAB · Apr 25, 2025 · IPR2024-01462 · APJ Jo-Anne M Kokoski · IPR · Institution

  The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–8 were unpatentable under the asserted obviousness grounds.

  RulingsInstitution decision

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “experience working on the development of materials or components for electronic devices such as batteries.” Pet. 2. Petitioner further contends that “[a]dditional education, such as a graduate degree, could compensate for less work experience, and additional work experience could compensate for less formal education.” Id. Patent Owner states that, “[f]or purposes of this Preliminary Response, Patent Owner applies Petitioner’s level of skill for a person of ordinary skill in the art.” Prelim. Resp. 4. For purposes of this Decision, we adopt Petitioner’s undisputed proposed definition because it appears to be consistent with the cited prior art and the disclosure of the ’014 patent. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (explaining that specific findings regarding ordinary skill level are not required “where the prior art itself reflects an appropriate level and a need for testimony is not shown” (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163 (Fed. Cir. 1985))).” slip op. at 8

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “customary meaning of such claim as understood by one of ordinary skill in the art and the prosecution history pertaining to the patent.” 37 C.F.R. § 42.100(b). Under this standard, claim terms are generally given their plain and ordinary meaning as would have been understood by a person of ordinary skill in the art at the time of the invention and in the context of the entire patent disclosure. Phillips v. AWH Corp., 415 F.3d 1303, 1313 (Fed. Cir. 2005) (en banc). Only those terms in controversy need to be construed, and only to the extent necessary to resolve the controversy. Realtime Data LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019). in this proceeding.” Pet. 3. Patent Owner contends that “[t]he Board need not construe any term in order to determine that institution should be denied.” Prelim. Resp. 4. Based on the record before us, we determine that no claim term requires express construction for purposes of this Decision. See Realtime Data, 912 F.3d at 1375.” slip op. at 8

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied

    “For these reasons, we are not persuaded that Petitioner sufficiently establishes that a POSITA would have been motivated to modify Hanafusa in light of Dobashi with a reasonable expectation of success as Petitioner contends. Accordingly, we determine that Petitioner fails to demonstrate a reasonable likelihood of prevailing in its assertion that the subject matter of claim 1, and claims 4 and 8 that depend therefrom, would have been obvious over the combined teachings of Hanafusa and Dobashi.” slip op. at 18

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable

    “Petitioner also focuses on Hanafusa’s teaching that all known methods can be used to make a rough surface low-profile, and Dobashi’s teaching that RSm can be used as an indicator for judgment of the surface, to support its contention that a POSITA would have been motivated to apply Dobashi’s RSm to further achieve Hanafusa’s purpose, without explaining how and why that would be the case. In particular, neither Petitioner nor Dr. Josefowicz adequately explain why a POSITA looking for ways to make Hanafusa’s surface roughness low-profile would look to methods to achieve as the period of waviness, RSm can also be used as an indicator for judgment of the surface.” Ex. 1005, 2:66–3:1, 6:23–26. Dobashi explains that waviness is “an indicator for determining whether the fine pattern forming performance is good or bad,” and “[t]he surface has small waviness and is smooth when RSm is large, and the surface has large waviness and is rough when RSm is small.” Id. at 3:1–3, 6:27–29. Dobashi also teaches that surface roughness Rzjis is used as a low-profile indicator. Ex. 1005, 2:66– 3:1. Dobashi, therefore, teaches that RSm is an indicator of surface waviness, which Dobashi explains is different than surface roughness. Id. at 2:66–3:3, 6:23–29. Given these teachings in Dobashi, neither Petitioner nor Dr. Josefowicz sufficiently explains how or why a POSITA would have been motivated to implement Dobashi’s RSm values to make Hanafusa’s surface roughness low-profile. See Pet. 10–12; Ex. 1003 ¶¶ 46–52.” slip op. at 14

  Claim construction§ 103 obviousnesscites Phillips · KSR
  Patents in suitUS 11,346,014
• Solus Advanced Materials Co., Ltd. v. SK Nexilis Co., Ltd.Institution denied
  PTAB · Apr 23, 2025 · IPR2024-01461 · APJ Jo-Anne M Kokoski · IPR · Institution

  The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–10 were unpatentable over either asserted § 103 ground.

  RulingsInstitution decision

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied

    “Institution of an inter partes review is authorized by statute when “the information presented in the petition . . . and any response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314 (2018); see also 37 C.F.R. § 42.4 (2023). For the reasons discussed below, we deny the Petition and do not institute an inter partes review.” slip op. at 2

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “II. ANALYSIS A. Level of Ordinary Skill in the Art Petitioner contends that a person of ordinary skill in the art (“POSITA”) “would have had at least an undergraduate degree in materials science, chemical engineering, electrical engineering, or related field, or equivalent knowledge, training, or experience, with at least two years of experience working on the development of materials or components for electronic devices such as batteries.” Pet. 4. Petitioner further contends that “[a]dditional education, such as a graduate degree, could compensate for less 7 We refer to the page numbers added by Petitioner to the bottom-center of the page. formal education.” Id. (citing Ex. 1003 ¶ 10). Patent Owner states that, “[f]or purposes of this Preliminary Response, Patent Owner applies Petitioner’s level of skill for a person of ordinary skill in the art.” Prelim. Resp. 4. For purposes of this Decision, we adopt Petitioner’s undisputed proposed definition because it appears to be consistent with the cited prior art and the disclosure of the ’689 patent. See Okajima v. Bourdeau, 261 F.3d 1350, 1355 (Fed. Cir. 2001) (explaining that specific findings regarding ordinary skill level are not required “where the prior art itself reflects an appropriate level and a need for testimony is not shown” (quoting Litton Indus. Prods., Inc. v. Solid State Sys. Corp., 755 F.2d 158, 163–64 (Fed. Cir. 1985))).” slip op. at 10

  • Expert testimonyPetitioner expert discountedDecided for patent owner

    “We are not persuaded, on this record, that Petitioner adequately establishes that Khatibi discloses a CTE in the claimed range of 16 to 22 µm/(m·°C.). Petitioner’s argument that Khatibi’s reported values meet this claim limitation are based solely on Dr. Randall’s testimony that Khatibi’s measurement method would produce results that would not significantly differ from results determined using the claimed method. See Pet. 16–18 (citing Ex. 1003 ¶¶ 56–60). Dr. Randall’s testimony, however, is largely conclusory and unsupported by adequate explanation and/or objective evidence. For example, Dr. Randall does not provide adequate explanation or objective evidence to support his opinion that Khatibi’s use of a laser speckle based dilatometer instead of the claimed thermomechanical analyzer “is unlikely to significantly impact the CTE value” because “variations in equipment and a heating speed of 5° C/min would not significantly alter the results.” Ex. 1003 ¶ 58. In particular, Dr. Randall neither explains what constitutes a “significant” impact on CTE, nor provides objective evidence to support his contention that equipment variations and heating differences would not “significantly alter” the resulting measurements. And although Dr. Randall opines that “the heating rate (5°C per minute) is typical for certain devices” such as a thermomechanical analyzer or dilatometer, and “[t]ypically, these devices use temperature ramp rates between 2°C and 20°C per minutes, so the ‘5° C./min’ recited in [1d] is common and should not drastically affect the measurement results,” Dr. Randall fails to point us to any evidence showing that these temperatures are “typical” or that the claimed heating rate is “common.” Id. ¶ 59 (emphases added). to little weight. See 37 C.F.R. § 42.65(a) (“Expert testimony that does not disclose the underlying facts or data on which the opinion is based is entitled to little or no weight.”); Xerox Corp. v. Bytemark, Inc., IPR2022-00624, Paper 12 at 5 (PTAB Feb. 10, 2023) (finding that “the Board was correct in giving little weight to Petitioner’s expert because the expert declaration merely offered conclusory assertions without underlying factual support”); Upjohn Co. v. Mova Pharm. Corp., 225 F.3d 1306, 1311 (Fed. Cir. 2000) (“Lack of factual support for expert opinion to factual determinations, however, may render the testimony of little probative value in a validity determination.” (quoting Ashland Oil, Inc. v. Delta Resins and Refractories, Inc., 776 F.2d 281, 294 (Fed. Cir. 1985))); see also In re Ethicon, Inc., 844 F.3d 1344, 1348, 1352 (Fed. Cir. 2017) (concluding that the Board properly gave “little weight” to conclusory expert testimony of objective indicia). Because Petitioner offers Dr. Randall’s testimony to supply a limitation missing from the prior art, namely, the CTE measurement method, and we give Dr. Randall’s unsupported and conclusory testimony little weight, we are not persuaded that Petitioner establishes a reasonable likelihood of showing that Khatibi discloses limitation [1d].” slip op. at 17

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable

    “second surfaces of the electrolytic copper foil ranges from 3 to 92.” Ex. 1001, 13:62–63. Petitioner contends that “Kim teaches that the electrolytic copper foil (e.g., untreated or treated copper foil) having Rz less than 2 µm is advantageous toward battery efficiency and performance,” and, similarly, Griesi describes the use of untreated electrolytic copper foil with an Rz value less than 2 µm in printed circuit boards that are compatible with secondary batteries. Pet. 58–59 (citing Ex. 1012, claim 2, ¶¶ 13, 25, 27; Ex. 1003 ¶ 157). In particular, Petitioner notes that Griesi’s Figure 3.16 describes an “Rz value of 1.2 µm.” Id. at 59 (citing Ex. 1015, 53–54; Ex. 1003 ¶ 158). Petitioner asserts that “Dr. Randall explains that a POSITA would have also recognized another surface roughness-related parameter, Rpc, in Griesi as a potentially useful parameter that can be optimized to further enhance uniformity or generally improve Kim’s copper foil surface, for example, to prevent wrinkles or achieve other advantageous effects.” Id. (citing Ex. 1003 ¶ 159). Although Dr. Randall demonstrates that Griesi’s Pc (or Rpc) value is 19.2 over a 4 mm sampling length (Ex. 1003 ¶ 155), Petitioner does not contend that Griesi addresses this value, or indicates any benefit that might be derived from its use. Instead, Griesi’s Pc value appears to be an incidental finding, which is not discussed or analyzed in the reference. See incidental, unexamined finding would lead a POSITA to import Griesi’s Pc value into Kim’s copper foil, absent a hindsight desire to reconstruct the claimed invention. As such, Petitioner’s arguments with respect to Kim and Griesi are not persuasive. See Cheese Sys. Inc. v. Tetra Pak Cheese and Powder Sys., Inc., 725 F.3d 1341, 1352 (Fed. Cir. 2013) (“Obviousness cannot be based on the hindsight combination of components selectively culled from the prior art to fit the parameters of the patented invention.” (internal quotations marks omitted)). Thus, we are not persuaded, on this record, that the combined disclosures of Kim and Griesi teach all of the elements of limitation [1g].” slip op. at 23

  § 103 obviousnesscites Phillips
  Patents in suitUS 10,811,689
• AT&T Services Inc. / T-Mobile USA, Inc. et al. v. Innovative Sonic Ltd.Institution denied
  PTAB · Dec 12, 2024 · IPR2024-00991 · APJ Juliet Mitchell Dirba · IPR · Institution

  The Board denied institution because Petitioner did not show a reasonable likelihood of prevailing on any asserted anticipation or obviousness ground for claims 1–11.

  RulingsInstitution decision

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied

    “An inter partes review may not be instituted unless “the information presented in the petition . . . and any response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a). Having reviewed the parties’ papers and the evidence of record, we determine that Petitioner has not shown a reasonable likelihood it will prevail in establishing the unpatentability of any of the challenged claims. Accordingly, we do not institute an inter partes review.” slip op. at 2

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “Patent Owner responds that “a person with the 3-year experience proposed by Petitioner would not have the intimate knowledge of the existing standardized cellular system” required to understand “how a proposed change would impact the rest of the system.” Prelim. Resp. 7. But Patent Owner also states that engineers participating in the development of the relevant cellular specifications “would not be expected to be familiar with all relevant aspects of the specifications” given their length and complexity. Id. at 7–8. For purposes of this Decision, we adopt Petitioner’s proposed level of skill, as articulated above, because we are satisfied that it generally comports with the level of skill necessary to understand and implement the teachings of the ’883 patent and the asserted prior art. To the extent Patent Owner disagrees (see Prelim. Resp. 6–8), it fails to sufficiently explain its contrary position by, for example, providing its own proposed level of skill.” slip op. at 9

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “Petitioner states that “the Board does not need to expressly construe any terms” in this proceeding because “the prior art in this Petition discloses all limitations under any plausible construction.” Pet. 10–11. Patent Owner similarly states that “all terms are entitled to their plain and ordinary meaning.” Prelim. Resp. 21. We agree with the parties that it is not necessary to construe any claim terms or phrases in this Decision. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe only those terms that are in controversy, and only to the extent necessary to resolve the controversy.”) (cleaned up).” slip op. at 9

  • Novelty / Anticipation (§102) › Anticipation standard (single reference, every element)Not shown unpatentableNot shown unpatentable

    “(step 406) discloses the claimed “second request” (Pet. 44–45),9 but Petitioner fails to show that this message discloses a request. See Prelim. Resp. 46–48. Han explains that the dual connection setup response in step 406 is a “dual connection setup request acknowledge (ACK)” message sent in response to “dual connection setup request” received in step 404. Ex. 1007 ¶¶ 40–42; accord Pet. 42–44. An acknowledgement is not a request, and Petitioner fails to sufficiently support its contention to the contrary (see Pet. 44–45). According to Petitioner, the acknowledgement message is “a request to change a data path” because the data path is “change[d] . . . based on this message” (id. at 45 (citing Ex. 1007 ¶¶ 42–47; Ex. 1003 ¶ 202)); however, this is faulty reasoning. At most, Petitioner’s argument shows that the acknowledgement is a message “to change a data 9 We note that this is the same message relied upon by Petitioner to teach the claimed “accept message” recited earlier in claim 1. Compare Pet. 44– 45, with id. at 43–44. We need not (and do not) decide whether Petitioner has sufficiently shown that this message discloses two separate claim elements. path,” not that it is a request to do so. In other words, even if Han’s acknowledgement message (in step 406) is a condition precedent to changing the data path, this does not make the message a “request.” Although Dr. Mahon agrees with Petitioner, his analysis mirrors Petitioner’s arguments and suffers from the same deficiencies. See Ex. 1003 ¶¶ 202– 203; see also Motorola, Inc. v. Interdigital Tech. Corp., 121 F.3d 1461, 1473 (Fed. Cir. 1997) (“An expert’s conclusory testimony, unsupported by the documentary evidence, cannot supplant the requirement of anticipatory disclosure in the prior art reference itself.”).” slip op. at 14

  Claim construction§ 102 anticipation§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,736,883
• Honeywell International Inc. v. DSM IP Assets B.V.Institution denied
  PTAB · Aug 21, 2024 · IPR2024-00493 · APJ Erica A Franklin · IPR · Institution

  The Board denied institution because Honeywell did not show a reasonable likelihood that claims 1–9 were unpatentable over any of its three obviousness combinations.

  RulingsInstitution decision

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied

    “Accordingly, we determine that Petitioner has not shown a reasonable likelihood of prevailing in its obviousness challenge of independent claim 1 or dependent claims 2–9 over the combination of Simmelink and Section 73.1015.” slip op. at 23

  • Skill levelOther

    “PHOSITA) at the time of the ’532 patent “would have had at least a Bachelor’s degree in the field of chemistry, chemical engineering, polymer chemistry, or materials science and at least three years of relevant work experience in the field of high strength fibers.” Pet. 8 (citing Ex. 1003 ¶ 18). Petitioner adds that individuals with different educational backgrounds could still be of ordinary skill in the art if they have “additional experience [that] compensates for a deficit in their education and experience stated above.” Id. According to Patent Owner, a person or ordinary skill in the art, would have (i) a bachelor’s degree in chemistry, polymer chemistry, materials science, chemical engineering, or biomedical engineering and (ii) three years of experience in designing and manufacturing gel-spun UHMWPE yarns. At this level of skill, a PHOSITA would have a detailed understanding of the information provided in the Technology Background, Section II, supra, including (i) the differences between linear HDPE and UHMWPE, (ii) the history underlying Section 73.1015 and the early failures of the 1960s-era blue, melt-extruded polyethylene sutures, (iii) why the molecular orientation of polyethylene molecules leads to strong yarns in the special case of gel-spun UHMWPE, and (iv) the challenges associated with coloring gel-spun UHMWPE yarns, especially for end-use medical applications. Prelim. Resp. 33–34. We note that the parties’ proposed definitions are largely similar, except that Patent Owner additionally recognizes a Bachelor’s degree in biomedical engineering and requires experience in designing and manufacturing gel-spun UHMWPE yarns. In any event, we do not need to the same under either proposed definition.” slip op. at 6

  • Claim Construction › Intrinsic evidence (Phillips canons) › Lexicography (patentee as own lexicographer)Term construed patent owner constructionDecided for patent owner

    “a skilled artisan would have understood that the “gel spinning” process recited in the claims requires the use of a solvent during the spinning process. Indeed, the Specification describes this term, as follows: Gel spinning is understood to include at least the steps of spinning filaments from a solution of ultra-high molecular weight polyethylene in a spin solvent; cooling the filament obtained to form a gel filament removing at least partly the spin solvent from the gel filament; removing at least partly the spin solvent from the gel filament; and drawing the filament in at least one drawing step before during or after removing spin solvent. Ex. 1001, 2:31–37. We recognize the inventor’s lexicography as dispositive with respect to the meaning of the term “gel spinning.” See Phillips v. AWHCorp., 415 F.3d 1303, 1316 (Fed. Cir. 2005); SciMed Life Sys., Inc. v. Advanced Cardiovascular Sys., Inc., 242 F.3d 1337, 1343–44 (Fed. Cir.” slip op. at 8

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITADecided for patent owner

    “Claim 1 describes gel spinning as the manner by which the filaments comprised in the claimed colored multi-filament yarn are obtained. This, on its face, is a product-by-process claim element because it describes the filament structure being obtained in a particular way, i.e., by gel spinning. See Kamstrup A/S v. Axioma Metering UAB, 43 F.4th 1374, 1382 (Fed. Cir. 2022) (agreeing with the Board that “cast in one piece” is a product-by-process claim element as it describes the structure being cast “in a particular way”). For this element to be limiting, it must impart “structural and functional differences” that distinguish the claimed product from the prior art. See Amgen Inc. v. F. Hoffman-La Roche Ltd, 580 F.3d 1340, 1365–67 (Fed. Cir. 2009). Patent Owner argues persuasively that gel spinning imparts structural and functional differences to the claimed product because the process “creates overlap between polyethylene molecules within the UHMWPE filaments that maximizes the intermolecular Van der Waals interactions, resulting in highly crystalline filaments with high tensile strength.” Prelim. Resp. 38, 22 (citing Ex. 1014, 62–66). According to Patent Owner, “the structure of the gel spun UHMWPE is substantially different from other types of UHMWPE such as compression-molded and ram-extruded UHMWPE used to make joint replacements and other orthopedic implants.” Id. at 38.” slip op. at 9

  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 10,280,532
• Alertus Technologies, LLC v. Desktop Alert, Inc.Institution denied
  PTAB · Jun 28, 2024 · IPR2024-00363 · APJ Andrew L Nalven · IPR · Institution

  The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–13 were unpatentable over the asserted obviousness combinations.

  RulingsInstitution decision

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied

    “Pursuant to 35 U.S.C. § 314(a), an inter partes review may not be instituted “unless . . . there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” For the reasons that follow, we determine that Petitioner has not demonstrated a reasonable likelihood of prevailing in demonstrating the unpatentability of any of the challenged claims. Accordingly, we do not institute an inter partes review.” slip op. at 2

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

    “Although claims 1 and 10 recite slightly different language, both clearly recite a “first triggering step” that precedes two subsequent polling steps. In the case of claim 1, the “first triggering step” precedes the “second step” and “fifth step.” See id. The explicit use of “second” and “fifth” supports limiting the steps to the recited order. See Mformation Techs., Inc. v. Research in Motion Ltd., 764 F.3d 1392, 1398 (Fed. Cir. 2014) (“[A] claim requires an ordering of steps when the claim language, as a matter of logic or grammar, requires that the steps be performed in the order written, or the specification directly or implicitly requires an order of steps.” (cleaned up)).” slip op. at 10

  • Skill levelSkill level petitioner adoptedDecided for petitioner

    “(“POSITA”) “would have (i) a bachelor’s degree or equivalent in electrical engineering, computer engineering, network engineering, computer science, and/or a related field and (ii) 1-3 years of experience relating to computer and networking systems and/or methods including systems and methods for messaging.” Pet. 4–5 (citing Ex. 1003 ¶¶ 25–26). Patent Owner does not offer a position as to the level of ordinary skill in the art. See generally Prelim. Resp. For purposes of this Decision, we adopt Petitioner’s assessment, which appears consistent with the level of skill reflected in the Specification and asserted prior art.” slip op. at 12

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentable

    “with Patent Owner that Dillon discloses time-stamps as “alternatives.” Prelim. Resp. 21 (citing Ex. 1005, 4:36–41). Dillon explains that “[t]he time-stamp . . . may represent the status of the subscriber’s e-mail account in various ways . . . [m]ost commonly, it is an indication of an actual time.” Ex. 1005, 7:19–21. However, Dillon explicitly states that “[a]lternatively, a time-stamp may be a number, such as a version number . . . or it may be a binary indication of whether or not e-mail . . . has been received.” Id. at 7:23–28 (emphasis added). Petitioner has not identified any portion of Dillon that suggests using more than one type of time-stamp in the same process. See generally Pet. 30–36. Dillon’s lack of disclosure of using multiple time-stamps appears consistent with Dillon’s description of the time-stamp as providing “the status of the subscriber’s e-mail account.” Ex. 1005, 7:19–21. Each disclosed alternative — time, version number, or binary indication — provides status information for the same purpose, namely, to indicate “whether or not e-mail for the given e-mail alert service subscriber has been received by the e-mail server 12 at any given time.” Id. at 7:27–29, 9:7–17. Because each of Dillon’s alternatives for a time-stamp serves the same purpose, we are not persuaded that Petitioner has provided sufficient reasoning to demonstrate that a POSITA would have been motivated to modify Dillon to both add a new polling step requesting a first time-stamp as a Boolean time-stamp and then request a second time-stamp as a version number or time indication. Indeed, Petitioner’s asserted rationale to modify Dillon here is conclusory and fails to explain sufficiently how using a second time-stamp will achieve the asserted benefits of reducing messaging bandwidth or uniquely identifying a particular message. See Pet. 31. Because Dr. Mangione-Smith’s declaration testimony mirrors Petitioner’s argument, his supporting testimony is similarly insufficient. Compare Pet. 31, with Ex. 1003 ¶ 62. See 37 C.F.R. § 42.65(a) (“Expert testimony that does not disclose the underlying facts or data on which the opinion is based is entitled to little or no weight.”); see also In re Am. Acad. of Sci. Tech Ctr., 367 F.3d 1359, 1368 (Fed. Cir. 2004) (noting that “the Board is entitled to weigh the declarations and conclude that the lack of factual corroboration warrants discounting the opinions expressed in the declarations”).” slip op. at 21

  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 9,172,765
• Nespresso USA, Inc. v. K-Fee System GmbHInstitution denied
  PTAB · Jun 10, 2024 · IPR2024-00239 · APJ Jon B Tornquist · IPR · Institution

  The Board denied institution because Petitioner did not show a reasonable likelihood that claims 1–20 would have been obvious over either asserted combination.

  RulingsInstitution decision

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied

    “review. 35 U.S.C. § 314 (2018); 37 C.F.R. § 42.4(a) (2022). The standard for institution is set forth in 35 U.S.C. § 314(a), which provides that an inter partes review may not be instituted “unless the Director determines . . . there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” For the reasons set forth below, Petitioner does not demonstrate a reasonable likelihood of prevailing with respect to any of claims 1–20 of the ’094 patent. Accordingly, we do not institute an inter partes review.” slip op. at 2

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed patent owner constructionDecided for patent owner

    “The express language of the claim, however, does not support using the “central axis” as the measuring point for determining if one object is laterally offset from another. For example, the term “central axis” is not used in the relevant claim phrase and the dictionary definitions of “lateral” relied upon by Petitioner and Mr. Jobin to show the ordinary meaning of the claim term do not suggest that the “central axis” is the reference point for determining whether a first object is “laterally offset” from a second object. As such, we determine that the claim language supports Patent Owner’s construction requiring that the “groove” be “off to the side” of the entire mandrel, and not merely the “central axis” of the mandrel. Prelim. Resp. 54. We must also resolve whether the entire groove is required to be laterally offset from the chamfered mandrel, or only a portion of it. On this point, the claims do not use the term “portion,” but rather specify that the “groove” is “laterally offset from the chamfered mandrel.” Ex. 1001, 14:4– 5, 15:19–20. This suggests that the entire “groove” must be offset from the “chamfered mandrel.”” slip op. at 10

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successMotivation not foundNot shown unpatentableNot shown unpatentable

    “That argument, however, does not explain why it would have been obvious to laterally offset the groove of Yoakim from the chamfered mandrel. Rather, as demonstrated by Mr. Jobin’s testimony, this argument relates to the general use of a sealing member in a groove, to the extent it was ultimately determined that such a configuration is not expressly disclosed in Yoakim. Id.; Ex. 1003 ¶ 296 (“It would have been obvious to one skilled in the art to position a sealing member in a groove to solidify the between counter-force portion 161 and engaging portion 157 in Figure 35 of Yoakim is more appropriately identified as the claimed “groove.” Prelim. Resp. 60–61. We need not resolve this issue, however, as Petitioner does not persuasively demonstrate that either potential “groove” is “laterally offset” from the chamfered mandrel. placement of the seal and improve its sealing stability and strength. Furthermore, it would have been obvious to one skilled in the art to utilize a groove and seal configuration in the brewing head . . . .”) (emphasis added). Even if we interpret the recited portion of the Petition as an argument for placing the groove entirely to the side of the mandrel in Yoakim, the Petition does not persuasively explain why one of ordinary skill in the art would have sought to do so. In Figure 35 of Yoakim, the seal and groove, as well as an elastic loading means, act as a valve means to control the level of pressure exerted in the capsule and “optimize interaction of water and the ground coffee particles to obtain a good extraction of the coffee and aroma compounds.” Ex. 1004 ¶¶ 370–372, 382, 396–398, 434–436, 445; Ex. 1003 ¶¶ 286–290; Pet. 63. These are the same beneficial properties relied upon by Petitioner to support the proposed combination, and Petitioner does not persuasively explain why one of ordinary skill in the art would have modified Yoakim in order to achieve results that are already obtained in the identified embodiment. Pet. 63. In view of the foregoing, we determine that Petitioner does not demonstrate a reasonable likelihood that claims 1 and 12 would have been obvious over the combined disclosures of Yoakim, Jarisch 929, and Rossi.” slip op. at 20

  Claim construction§ 103 obviousnesscites Phillips · KSR · Graham
  Patents in suitUS 11,542,094
• Mahle Behr Charleston Inc. v. Frank Amidio CatalanoOther
  PTAB · May 24, 2024 · IPR2023-00861 · APJ Christopher M Kaiser · IPR · Remand

  The Board denied institution because Petitioner did not show a reasonable likelihood that any challenged claim was unpatentable under any asserted ground.

  RulingsRemand decision

  • RemandOther

    “Accordingly, the Director instructed us to “determine whether Petitioner has demonstrated that Figure 1 of Godefroy ‘is clear on its face’ or would have reasonably suggested the placement of Godefroy’s sacrificial anode ‘within 10 inches’ of the hot liquid inlet.” Id. at 9. “In making this determination,” the Director instructed us to “consider whether the expert testimony provides sufficient ‘technical detail, explanation, or statements supporting why the expert determines that the feature in question was required or would have been obvious based on the prior art disclosure.’” Id. In addition, although the Director’s decision “is limited to [our] application of Hockerson to the grounds in the Petition involving Godefroy,” the Director instructed us also to “consider what effect, if any, this decision has on the other asserted grounds.” Id. Finally, the Director instructed us to “set forth [our] interpretation” of “the limitation ‘within 10 inches of a hot liquid inlet to the radiator.’” Id. at 8 n.4.” slip op. at 4

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied

    “original decision, the Director’s decision, and the evidence currently of record, we determine that Petitioner has not shown a reasonable likelihood that it will prevail in showing that at least one of the challenged claims is unpatentable. Accordingly, we do not institute an inter partes review of any challenged claim based on any ground asserted in the Petition. IV. ORDER For the reasons given, it is: ORDERED that, pursuant to 35 U.S.C. § 314, the Petition is denied, and no inter partes review is instituted.” slip op. at 19

  • Claim Construction › Intrinsic evidence (Phillips canons) › Plain and ordinary meaning to a POSITATerm construed petitioner constructionDecided for petitioner

    “evidence. The challenged claims require that a sacrificial anode be placed within a certain distance—10 inches—of the hot liquid inlet, and, because the inlet has some non-zero size, it might be possible for an anode to be within that distance from some parts, but not from all parts, of the inlet. Accordingly, specifying the center axis of the inlet as the point from which to measure the distance to the anode improves on the plain words of the claim in terms of achieving the claim’s objective of placing the anode within a specified distance of the inlet. Moreover, when discussing the distance from the inlet to the anode, the specification of the ’494 patent uses the language “within 10 inches in any direction of the center axis of the inlet connection.” Ex. 1001, 7:61–64. Thus, the intrinsic evidence supports adopting Petitioner’s claim construction. Petitioner’s declarant, Dr. Medlin, relies on Petitioner’s proposed construction. See, e.g., Ex. 1004 ¶¶ 20 (noting that the construction “within 10 inches of the center axis of [a] hot liquid inlet” “ha[s] been adopted by Petitioner”), 96 (“the sacrificial anodes contained in each of the turbulators 2 would be placed within 10 inches of a center axis of a hot liquid inlet to the radiator of Tomosada”), 144 (“A POSITA would understand from Figure 1 that the sacrificial anode 14 is within 10 inches of a center axis of a hot liquid inlet”), 267 (“These teachings would further motivate a POSITA to located the sacrificial anode 12 within 10 inches of a center axis of the hot liquid inlet.”). This support for Petitioner’s proposed construction provides further reason for us to adopt it. Because it is supported by the intrinsic evidence of record, because Patent Owner proposes no alternative construction, and because Petitioner’s expert supports it, we adopt the construction of “within 10 inches of a hot liquid inlet to the radiator” that Petitioner proposes. Thus, we construe this term as “within 10 inches of the center axis of a hot liquid inlet to the radiator.” In other words, when discussing the distance between a hot liquid inlet and a sacrificial anode, we interpret “hot liquid inlet” as “center axis of the hot liquid inlet.”” slip op. at 5

  • BurdenNot shown unpatentable

    “Inherency may be relied upon in arguing either anticipation or obviousness. Schering, 339 F.3d at 1377 (applying inherency in an anticipation context); Par Pharma. Inc. v. TWI Pharma., Inc., 773 F.3d 1186, 1195–96 (Fed. Cir. 2014) (applying inherency in an obviousness context). In both cases, however, “[t]he mere fact that a certain thing may result from a given set of circumstances is not sufficient.” Therasense, Inc. v. Becton, Dickinson & Co., 593 F.3d 1325, 1332 (Fed. Cir. 2010). Instead, “the limitation at issue necessarily must be present, or the natural result of the combination of elements expressly disclosed by the prior art.” Par Pharma., 773 F.3d at 1195–96. Here, Petitioner has not shown sufficiently that, in Godefroy, the sacrificial anode necessarily is placed within 10 inches of the center axis of the hot liquid inlet. Dr. Medlin testifies that Figure 1 of Godefroy shows that “an entirety . . . or at least a significant portion of the sacrificial anode 14, is within 10 inches of a center axis of the inlet.” Ex. 1004 ¶ 144. But we cannot say that Figure 1 of Godefroy is clear on its face, or reasonably suggests, that this is necessarily the case. There are no dimensions shown on Figure 1, so it is unclear from the figure what the diameter of pipe 12 is. If that diameter is larger than 20 inches, then it simply is untrue that “sacrificial anode 14 is . . . necessarily placed within 10 inches of a center axis of a hot liquid inlet to the radiator,” as Dr. Medlin testifies. Id. ¶ 361. As noted above, neither Petitioner nor Dr. Medlin relies on the hot liquid inlet of Godefroy having any particular diameter, and Godefroy is silent as to the diameter of its inlet. Pet. 69–70; Ex. 1004 ¶¶ 144, 359–361, 381–382, 406–408; Ex. 1008, 1–15. Moreover, as Patent Owner notes, there is a wide range of sizes of radiators, including automobile radiators, available. Prelim. Resp. 3–5; Exs. 2001–2003. In the absence of any testimony or other evidence that tends to show that radiator inlet pipes necessarily have diameters less than 20 inches, Petitioner has not shown sufficiently that the diameter of Godefroy’s inlet pipe is small enough to ensure that any portion of the anode necessarily is within 10 inches of the center axis of the inlet.” slip op. at 11

  Claim constructioncites Phillips
• Aylo Freesites Ltd. v. DISH Technologies L.L.C.Institution denied
  PTAB · Apr 25, 2024 · IPR2024-00147 · APJ Juliet Mitchell Dirba · IPR · Institution

  The Board denied institution on all challenged claims because Petitioner did not show a reasonable likelihood that any claim was obvious over the asserted grounds.

  RulingsInstitution decision

  • PTAB / AIA Trials › Institution threshold (reasonable likelihood / more likely than not)Institution denied meritsInstitution denied

    “An inter partes review may not be instituted unless “the information presented in the petition . . . and any response . . . shows that there is a reasonable likelihood that the petitioner would prevail with respect to at least 1 of the claims challenged in the petition.” 35 U.S.C. § 314(a). Having reviewed the parties’ papers and the evidence of record, we determine that Petitioner has not shown a reasonable likelihood it will prevail in establishing the unpatentability of any of the challenged claims. Accordingly, we do not institute an inter partes review.” slip op. at 2

  • Skill levelSkill level petitioner adoptedOther

    “to either: (1) “a B.S. degree in computer science or electrical engineering (or comparable degree) and two years of experience in networking or streaming media,” or (2) “a M.S. in computer science or electrical engineering (or comparable degree).” Pet. 8 (citing Ex. 1003 ¶ 42). At this stage, Patent Owner “disputes Petitioner’s definition,” but does not explain what it disputes. Prelim. Resp. 2. For purposes of this Decision, we adopt Petitioner’s proposed level of skill, as articulated above. We are satisfied that it comports with the level of skill necessary to understand and implement the teachings of the ’156 patent and the asserted prior art.” slip op. at 8

  • Claim Construction › Threshold & procedure › Whether a term needs construction (O2 Micro)No construction neededOther

    “We determine that it is not necessary to expressly construe any claim terms or phrases for purposes of this Decision. See Realtime Data, LLC v. Iancu, 912 F.3d 1368, 1375 (Fed. Cir. 2019) (“The Board is required to construe ‘only those terms . . . that are in controversy, and only to the extent necessary to resolve the controversy.’”) (quoting Vivid Techs., Inc. v. Am. Sci. & Eng’g, Inc., 200 F.3d 795, 803 (Fed. Cir. 1999))).” slip op. at 9

  • Obviousness (§103) › Motivation to combine / reasonable expectation of successNot shown unpatentableMotivation not foundNot shown unpatentable

    “Petitioner fails to provide a sufficient basis for that contention. See Pet. 20– 21; PAR Pharm., Inc. v. TWI Pharms., Inc., 773 F.3d 1186, 1196 (Fed. Cir. 2014) (explaining that inherency requires a showing that “the limitation at issue necessarily must be present”). Moreover, Petitioner does not contend that Ogdon suggests (or renders obvious) element 1[A][3]. See Pet. 19–21. Further, even if the Petition could be read as including such a contention, we would preliminarily find, on this record, that Ogdon does not suggest storing multiple copies of the same video encoded at different bitrates, and that Petitioner fails to provide any rationale to support a theory that element 1[A][3] would have been obvious over Ogdon alone.11 In other words, even if an ordinarily skilled artisan could have modified Ogdon to store multiple copies of the same video encoded at different bitrates, Petitioner does not provide any rationale to support a contention that an ordinary artisan would have been motivated to implement Ogdon in this 11 The Board instituted inter partes review in other proceedings in which Petitioner contends that claim limitations including some of the same subject matter are taught or suggested by a combination of Ogdon and WO 02/075482 A2 (Allen). E.g., IPR2024-00044, Paper 1 at 21–24. There is no tension between this Decision and those other decisions because Petitioner’s contentions in those other proceedings are based on materially different arguments and evidence. manner. See, e.g., Belden Inc. v. Berk-Tek LLC, 805 F.3d 1064, 1073 (Fed. Cir. 2015) (“[O]bviousness concerns whether a skilled artisan not only could have made but would have been motivated to make the combinations or modifications of prior art to arrive at the claimed invention.”) (citing InTouch Techs., Inc. v. VGO Commc’ns, Inc., 751 F.3d 1327, 1352 (Fed. Cir. 2014)). Accordingly, we determine that Petitioner fails to show a reasonable likelihood that it will prevail on its contention that Ogdon discloses “the video server stores multiple different copies of the video encoded at different bit rates as multiple sets of streamlets,” as required by claim 1. Ex. 1001, 13:58–61 (element 1[A][3]). Consequently, Petitioner does not show that there is a reasonable likelihood that it would prevail in establishing that the subject matter of claim 1 would have been obvious over Ogdon.” slip op. at 20

  Claim construction§ 103 obviousnesscites Phillips · Graham
  Patents in suitUS 10,757,156

Holdings, summaries, rulings, issues, outcomes, winners and claim constructions shown for a decision were generated by a large language model reading the opinion. They are a guide to the decision, not the decision. Confirm every one against the court's own text before relying on it. Outcomes read from the patent owner’s side. Party names are extracted from the decision and are missing on about 900 short Director denials and scans, which carry the trial number instead.